Skip to contentSkip to conversation

gianfar: Fix half-duplex operation for non-MII/RMII interfaces

PATCH In review Anton Vorontsov 1 participant 1 message Jun 25, 2009

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH v2 2/2 gianfar: Fix half-duplex operation for non-MII/RMII interfaces

It appears that gianfar driver has the same problem with RGMII half-duplex mode as ucc_geth.

NFS boot using 10/half link takes about 10 minutes to complete:

eth0: Gianfar Ethernet Controller Version 1.2, 00:11:22:33:44:55
eth0: Running with NAPI enabled
eth0: 256/256 RX/TX BD ring size
[...]
Sending DHCP requests .
PHY: mdio@e0024520:02 - Link is Up - 10/Half
., OK
[...]
Looking up port of RPC 100003/2 on 10.0.0.2
Looking up port of RPC 100005/1 on 10.0.0.2
VFS: Mounted root (nfs filesystem) readonly on device 0:11. Freeing unused kernel memory: 188k init
nfs: server 10.0.0.2 not responding, still trying
nfs: server 10.0.0.2 OK
nfs: server 10.0.0.2 not responding, still trying
nfs: server 10.0.0.2 not responding, still trying
nfs: server 10.0.0.2 not responding, still trying [... few minutes of OK/not responding flood ...]

And just as with ucc_geth, statistic shows errors:

  # ethtool -S eth0 | grep -v ": 0"
  NIC statistics:
       rx-dropped-by-kernel: 2
       tx-rx-64-frames: 49
       tx-rx-65-127-frames: 1270
       tx-rx-128-255-frames: 9992
       tx-rx-256-511-frames: 75
       tx-rx-512-1023-frames: 142
       tx-rx-1024-1518-frames: 8828
       rx-bytes: 13299414
       rx-packets: 13122
       rx-jabber-frames: 9
       tx-byte-counter: 1284847
       tx-packets: 8115
       tx-broadcast-packets: 3
       tx-deferral-packets: 43
       tx-single-collision-packets: 15
       tx-multiple-collision-packets: 301
       tx-late-collision-packets: 872
       tx-total-collision: 999
       tx-undersize-frames: 6

The symptoms were observed on MPC8379E-RDB boards (eTSEC). Although I didn't find where documentation forbids clearing Full Duplex bit for non-MII/RMII modes, it's pretty distinct that the bit should be set for RGMII.

It's no wonder though, QE Ethernet and TSEC are pretty similar.

---
 drivers/net/gianfar.c |    9 +++++++--
 1 files changed, 7 insertions(+), 2 deletions(-)
drivers/net/gianfar.c +7 -2
index 8741bb0..503b455 100644
@@ -1984,13 +1984,18 @@ static void adjust_link(struct net_device *dev)
 	if (phydev->link) {
 		u32 tempval = gfar_read(&regs->maccfg2);
 		u32 ecntrl = gfar_read(&regs->ecntrl);
+		phy_interface_t phyi = phydev->interface;
 
 		/* Now we make sure that we can be in full duplex mode.
 		 * If not, we operate in half-duplex mode. */
 		if (phydev->duplex != priv->oldduplex) {
 			new_state = 1;
-			if (!(phydev->duplex))
-				tempval &= ~(MACCFG2_FULL_DUPLEX);
+			if (!phydev->duplex &&
+					(phyi == PHY_INTERFACE_MODE_MII ||
+					 phyi == PHY_INTERFACE_MODE_RMII ||
+					 (phyi == PHY_INTERFACE_MODE_GMII &&
+					  phydev->speed < 1000)))
+				tempval &= ~MACCFG2_FULL_DUPLEX;
 			else
 				tempval |= MACCFG2_FULL_DUPLEX;
 
Signature · 1 line
1.6.3.1