hwmon: Add driver for Texas
PATCH v2 1/2 hwmon: Add driver for Texas
Add support for Texas Instruments TMP421/422/423 temperature sensor IC.
TI's TMP421/422/423 are I2C temperature sensor chips. These chips are similar to TI's TMP401/411 chips, but with reduced functionality (only temperature measurement). The chips have one local sensor and up to three (TMP423) remote sensors.
Changes in v2:
Jean, I've fixed all the issues from your review. Biggest change is introducing a sysfs group with the is_visible() calllback. Now only the supported temperature files appears in sysfs.
--- Kconfig | 10 + Makefile | 1 tmp421.c | 349 +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 360 insertions(+)
Index: linux-2.6/drivers/hwmon/tmp421.c
=================================--- /dev/null 1970-01-01 00:00:00.000000000 +0000
+++ linux-2.6/drivers/hwmon/tmp421.c 2009-06-23 19:58:56.000000000 +0200
@@ -0,0 +1,349 @@
+/* tmp421.c
+ *
+ * Copyright (C) 2009 Andre Prendel <[email protected]>
+ * Preliminary support by:
+ * Melvin Rook, Raymond Ng
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+/*
+ * Driver for the Texas Instruments TMP421 SMBus temperature sensor IC.
+ * Supported models: TMP421, TMP422, TMP423
+ */
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/slab.h>
+#include <linux/jiffies.h>
+#include <linux/i2c.h>
+#include <linux/hwmon.h>
+#include <linux/hwmon-sysfs.h>
+#include <linux/err.h>
+#include <linux/mutex.h>
+#include <linux/sysfs.h>
+
+/* Addresses to scan */
+static unsigned short normal_i2c[] = { 0x2a, 0x4c, 0x4d, 0x4e, 0x4f,
+ I2C_CLIENT_END };
+
+/* Insmod parameters */
+I2C_CLIENT_INSMOD_3(tmp421, tmp422, tmp423);
+
+/* The TMP421 registers */
+#define TMP421_CONFIG_REG_1 0x09
+#define TMP421_CONVERSION_RATE_REG 0x0B
+#define TMP421_MANUFACTURER_ID_REG 0xFE
+#define TMP421_DEVICE_ID_REG 0xFF
+
+static const u8 TMP421_TEMP_MSB[4] = { 0x00, 0x01, 0x02, 0x03 };
+static const u8 TMP421_TEMP_LSB[4] = { 0x10, 0x11, 0x12, 0x13 };
+
+/* Flags */
+#define TMP421_CONFIG_SHUTDOWN 0x40
+#define TMP421_CONFIG_RANGE 0x04
+
+/* Manufacturer / Device ID's */
+#define TMP421_MANUFACTURER_ID 0x55
+#define TMP421_DEVICE_ID 0x21
+#define TMP422_DEVICE_ID 0x22
+#define TMP423_DEVICE_ID 0x23
+
+static const struct i2c_device_id tmp421_id[] = {
+ { "tmp421", tmp421 },
+ { "tmp422", tmp422 },
+ { "tmp423", tmp423 },
+ { }
+};
+MODULE_DEVICE_TABLE(i2c, tmp421_id);
+
+struct tmp421_data {
+ struct device *hwmon_dev;
+ struct mutex update_lock;
+ char valid;
+ unsigned long last_updated;
+ int kind;
+ u8 config;
+ s16 temp[4];
+};
+
+static int temp_from_s16(s16 reg)
+{
+ int temp = reg;
+
+ return (temp * 1000 + 128) / 256;
+}
+
+static int temp_from_u16(u16 reg)
+{
+ int temp = reg;
+
+ /* Add offset for extended temperature range. */
+ temp -= 64 * 256;
+
+ return (temp * 1000 + 128) / 256;
+}
+
+static struct tmp421_data *tmp421_update_device(struct device *dev) +{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct tmp421_data *data = i2c_get_clientdata(client);
+ int i;
+
+ mutex_lock(&data->update_lock);
+
+ if (time_after(jiffies, data->last_updated + 2 * HZ) || !data->valid) {
+ data->config = i2c_smbus_read_byte_data(client,
+ TMP421_CONFIG_REG_1);
+
+ for (i = 0; i <= data->kind; i++) {
+ data->temp[i] = i2c_smbus_read_byte_data(client,
+ TMP421_TEMP_MSB[i]) << 8;
+ data->temp[i] |= i2c_smbus_read_byte_data(client,
+ TMP421_TEMP_LSB[i]);
+ }
+ data->last_updated = jiffies;
+ data->valid = 1;
+ }
+
+ mutex_unlock(&data->update_lock);
+
+ return data;
+}
+
+static ssize_t show_temp_value(struct device *dev,
+ struct device_attribute *devattr, char *buf)
+{
+ int index = to_sensor_dev_attr(devattr)->index;
+ struct tmp421_data *data = tmp421_update_device(dev);
+ int temp;
+
+ mutex_lock(&data->update_lock);
+ if (data->config & TMP421_CONFIG_RANGE)
+ temp = temp_from_u16(data->temp[index]);
+ else
+ temp = temp_from_s16(data->temp[index]);
+ mutex_unlock(&data->update_lock);
+
+ return sprintf(buf, "%d\n", temp);
+}
+
+static ssize_t show_fault(struct device *dev,
+ struct device_attribute *devattr, char *buf)
+{
+ int index = to_sensor_dev_attr(devattr)->index;
+ struct tmp421_data *data = tmp421_update_device(dev);
+
+ /*
+ * The OPEN bit signals a fault. This is bit 0 of the temperature
+ * register (low byte).
+ */
+ if (data->temp[index] & 0x01)
+ return sprintf(buf, "1\n");
+ else
+ return sprintf(buf, "0\n");
+}
+
+static mode_t tmp421_is_visible(struct kobject *kobj, struct attribute *a,
+ int n)
+{
+ struct device *dev = container_of(kobj, struct device, kobj);
+ struct i2c_client *client = to_i2c_client(dev);
+ struct tmp421_data *data = i2c_get_clientdata(client);
+ struct device_attribute *devattr;
+ unsigned int index;
+
+ devattr = container_of(a, struct device_attribute, attr);
+ index = to_sensor_dev_attr(devattr)->index;
+
+ if (data->kind > index)
+ return a->mode;
+
+ return 0;
+}
+
+static SENSOR_DEVICE_ATTR(temp1_input, S_IRUGO, show_temp_value, NULL, 0); +static SENSOR_DEVICE_ATTR(temp2_input, S_IRUGO, show_temp_value, NULL, 1); +static SENSOR_DEVICE_ATTR(temp2_fault, S_IRUGO, show_fault, NULL, 1); +static SENSOR_DEVICE_ATTR(temp3_input, S_IRUGO, show_temp_value, NULL, 2); +static SENSOR_DEVICE_ATTR(temp3_fault, S_IRUGO, show_fault, NULL, 2); +static SENSOR_DEVICE_ATTR(temp4_input, S_IRUGO, show_temp_value, NULL, 3); +static SENSOR_DEVICE_ATTR(temp4_fault, S_IRUGO, show_fault, NULL, 3); +
+static struct attribute *tmp421_attr[] = {
+ &sensor_dev_attr_temp1_input.dev_attr.attr,
+ &sensor_dev_attr_temp2_input.dev_attr.attr,
+ &sensor_dev_attr_temp2_fault.dev_attr.attr,
+ &sensor_dev_attr_temp3_input.dev_attr.attr,
+ &sensor_dev_attr_temp3_fault.dev_attr.attr,
+ &sensor_dev_attr_temp4_input.dev_attr.attr,
+ &sensor_dev_attr_temp4_fault.dev_attr.attr,
+ NULL
+};
+
+static const struct attribute_group tmp421_group = {
+ .attrs = tmp421_attr,
+ .is_visible = tmp421_is_visible,
+};
+
+static int tmp421_init_client(struct i2c_client *client)
+{
+ int config, config_orig;
+
+ /* Set the conversion rate to 2 Hz */
+ i2c_smbus_write_byte_data(client, TMP421_CONVERSION_RATE_REG, 0x05);
+
+ /* Start conversions (disable shutdown if necessary) */
+ config = i2c_smbus_read_byte_data(client, TMP421_CONFIG_REG_1);
+ if (config < 0) {
+ dev_err(&client->dev, "Could not read configuration"
+ " register (%d)\n", config);
+ return -ENODEV;
+ }
+
+ config_orig = config;
+ config &= ~TMP421_CONFIG_SHUTDOWN;
+
+ if (config != config_orig) {
+ dev_info(&client->dev, "Enable monitoring chip\n");
+ i2c_smbus_write_byte_data(client, TMP421_CONFIG_REG_1, config);
+ }
+
+ return 0;
+}
+
+static int tmp421_detect(struct i2c_client *client, int kind,
+ struct i2c_board_info *info)
+{
+ struct i2c_adapter *adapter = client->adapter;
+ const char *names[] = { "TMP421", "TMP422", "TMP423" };
+
+ if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA))
+ return -ENODEV;
+
+ if (kind <= 0) {
+ u8 reg;
+
+ reg = i2c_smbus_read_byte_data(client,
+ TMP421_MANUFACTURER_ID_REG);
+ if (reg != TMP421_MANUFACTURER_ID)
+ return -ENODEV;
+
+ reg = i2c_smbus_read_byte_data(client,
+ TMP421_DEVICE_ID_REG);
+ switch (reg) {
+ case TMP421_DEVICE_ID:
+ kind = tmp421;
+ break;
+ case TMP422_DEVICE_ID:
+ kind = tmp422;
+ break;
+ case TMP423_DEVICE_ID:
+ kind = tmp423;
+ break;
+ default:
+ return -ENODEV;
+ }
+ }
+ strlcpy(info->type, tmp421_id[kind - 1].name, I2C_NAME_SIZE);
+ dev_info(&adapter->dev, "Detected TI %s chip\n", names[kind - 1]);
+
+ return 0;
+}
+
+static int tmp421_remove(struct i2c_client *client)
+{
+ struct tmp421_data *data = i2c_get_clientdata(client);
+
+ if (data->hwmon_dev)
+ hwmon_device_unregister(data->hwmon_dev);
+
+ sysfs_remove_group(&client->dev.kobj, &tmp421_group);
+
+ i2c_set_clientdata(client, NULL);
+ kfree(data);
+
+ return 0;
+}
+
+static int tmp421_probe(struct i2c_client *client,
+ const struct i2c_device_id *id)
+{
+ struct tmp421_data *data;
+ int err;
+
+ data = kzalloc(sizeof(struct tmp421_data), GFP_KERNEL);
+ if (!data)
+ return -ENOMEM;
+
+ i2c_set_clientdata(client, data);
+ mutex_init(&data->update_lock);
+ data->kind = id->driver_data;
+
+ err = tmp421_init_client(client);
+ if (err)
+ goto exit_free;
+
+ err = sysfs_create_group(&client->dev.kobj, &tmp421_group);
+ if (err)
+ goto exit_free;
+
+ data->hwmon_dev = hwmon_device_register(&client->dev);
+ if (IS_ERR(data->hwmon_dev)) {
+ err = PTR_ERR(data->hwmon_dev);
+ data->hwmon_dev = NULL;
+ goto exit_remove;
+ }
+ return 0;
+
+exit_remove:
+ sysfs_remove_group(&client->dev.kobj, &tmp421_group);
+
+exit_free:
+ i2c_set_clientdata(client, NULL);
+ kfree(data);
+
+ return err;
+}
+
+static struct i2c_driver tmp421_driver = {
+ .class = I2C_CLASS_HWMON,
+ .driver = {
+ .name = "tmp421",
+ },
+ .probe = tmp421_probe,
+ .remove = tmp421_remove,
+ .id_table = tmp421_id,
+ .detect = tmp421_detect,
+ .address_data = &addr_data,
+};
+
+static int __init tmp421_init(void)
+{
+ return i2c_add_driver(&tmp421_driver);
+}
+
+static void __exit tmp421_exit(void)
+{
+ i2c_del_driver(&tmp421_driver);
+}
+
+MODULE_AUTHOR("Andre Prendel <[email protected]>"); +MODULE_DESCRIPTION("Texas Instruments TMP421/422/423 temperature sensor"
+ " driver");
+MODULE_LICENSE("GPL");
+
+module_init(tmp421_init);
+module_exit(tmp421_exit);
Index: linux-2.6/drivers/hwmon/Kconfig
=================================--- linux-2.6.orig/drivers/hwmon/Kconfig 2009-06-18 19:45:08.000000000 +0200
+++ linux-2.6/drivers/hwmon/Kconfig 2009-06-18 19:54:36.000000000 +0200
@@ -797,6 +797,16 @@
This driver can also be built as a module. If so, the module will be called tmp401.
+config SENSORS_TMP421
+ tristate "Texas Instruments TMP421, TMP422 and TMP423"
+ depends on I2C && EXPERIMENTAL
+ help
+ If you say yes here you get support for Texas Instruments TMP421
+ temperature sensor chips.
+
+ This driver can also be built as a module. If so, the module
+ will be called tmp421.
+
config SENSORS_VIA686A
tristate "VIA686A"
depends on PCI
Index: linux-2.6/drivers/hwmon/Makefile
=================================--- linux-2.6.orig/drivers/hwmon/Makefile 2009-06-18 19:45:08.000000000 +0200
+++ linux-2.6/drivers/hwmon/Makefile 2009-06-18 19:54:36.000000000 +0200
@@ -83,6 +83,7 @@
obj-$(CONFIG_SENSORS_SMSC47M192)+= smsc47m192.o
obj-$(CONFIG_SENSORS_THMC50) += thmc50.o
obj-$(CONFIG_SENSORS_TMP401) += tmp401.o
+obj-$(CONFIG_SENSORS_TMP421) += tmp421.o
obj-$(CONFIG_SENSORS_VIA686A) += via686a.o
obj-$(CONFIG_SENSORS_VT1211) += vt1211.o
obj-$(CONFIG_SENSORS_VT8231) += vt8231.o
_______________________________________________
lm-sensors mailing list
[email protected]
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
Hi Andre,
Quoted 13 lines · Andre Prendel
Add support for Texas Instruments TMP421/422/423 temperature sensor IC.
TI's TMP421/422/423 are I2C temperature sensor chips. These chips are similar to TI's TMP401/411 chips, but with reduced functionality (only temperature measurement). The chips have one local sensor and up to three (TMP423) remote sensors.
Changes in v2:
Jean, I've fixed all the issues from your review. Biggest change is introducing a sysfs group with the
is_visible()calllback. Now only the supported temperature files appears in sysfs.
Quoted 6 lines
Signed-off-by Andre Prendel <[email protected]>--- Kconfig | 10 + Makefile | 1 tmp421.c | 349 +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 360 insertions(+)
Looks mostly OK now. I have a few comments remaining, see below. But I will fix these myself, no need to resend.
Quoted 159 lines
Index:
linux-2.6/drivers/hwmon/tmp421.c
=================================> ---/dev/null1970-01-01 00:00:00.000000000 +0000
+++linux-2.6/drivers/hwmon/tmp421.c2009-06-23 19:58:56.000000000 +0200(quoted diff) +154
-0@@ -0,0 +1,349 @@ +/* tmp421.c + * + * Copyright (C) 2009 Andre Prendel <[email protected]> + * Preliminary support by: + * Melvin Rook, Raymond Ng + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + */ + +/* + * Driver for the Texas Instruments TMP421 SMBus temperature sensor IC. + * Supported models: TMP421, TMP422, TMP423 + */ + +#include <linux/module.h> +#include <linux/init.h> +#include <linux/slab.h> +#include <linux/jiffies.h> +#include <linux/i2c.h> +#include <linux/hwmon.h> +#include <linux/hwmon-sysfs.h> +#include <linux/err.h> +#include <linux/mutex.h> +#include <linux/sysfs.h> + +/* Addresses to scan */ +static unsigned short normal_i2c[] = { 0x2a, 0x4c, 0x4d, 0x4e, 0x4f, + I2C_CLIENT_END }; + +/* Insmod parameters */ +I2C_CLIENT_INSMOD_3(tmp421, tmp422, tmp423); + +/* The TMP421 registers */ +#define TMP421_CONFIG_REG_1 0x09 +#define TMP421_CONVERSION_RATE_REG 0x0B +#define TMP421_MANUFACTURER_ID_REG 0xFE +#define TMP421_DEVICE_ID_REG 0xFF + +static const u8 TMP421_TEMP_MSB[4] = { 0x00, 0x01, 0x02, 0x03 }; +static const u8 TMP421_TEMP_LSB[4] = { 0x10, 0x11, 0x12, 0x13 }; + +/* Flags */ +#define TMP421_CONFIG_SHUTDOWN 0x40 +#define TMP421_CONFIG_RANGE 0x04 + +/* Manufacturer / Device ID's */ +#define TMP421_MANUFACTURER_ID 0x55 +#define TMP421_DEVICE_ID 0x21 +#define TMP422_DEVICE_ID 0x22 +#define TMP423_DEVICE_ID 0x23 + +static const struct i2c_device_id tmp421_id[] = { + { "tmp421", tmp421 }, + { "tmp422", tmp422 }, + { "tmp423", tmp423 }, + { } +}; +MODULE_DEVICE_TABLE(i2c, tmp421_id); + +struct tmp421_data { + struct device *hwmon_dev; + struct mutex update_lock; + char valid; + unsigned long last_updated; + int kind; + u8 config; + s16 temp[4]; +}; + +static int temp_from_s16(s16 reg) +{ + int temp = reg; + + return (temp * 1000 + 128) / 256; +} + +static int temp_from_u16(u16 reg) +{ + int temp = reg; + + /* Add offset for extended temperature range. */ + temp -= 64 * 256; + + return (temp * 1000 + 128) / 256; +} + +static struct tmp421_data *tmp421_update_device(struct device *dev) +{ + struct i2c_client *client = to_i2c_client(dev); + struct tmp421_data *data = i2c_get_clientdata(client); + int i; + + mutex_lock(&data->update_lock); + + if (time_after(jiffies, data->last_updated + 2 * HZ) || !data->valid) { + data->config = i2c_smbus_read_byte_data(client, + TMP421_CONFIG_REG_1); + + for (i = 0; i <= data->kind; i++) { + data->temp[i] = i2c_smbus_read_byte_data(client, + TMP421_TEMP_MSB[i]) << 8; + data->temp[i] |= i2c_smbus_read_byte_data(client, + TMP421_TEMP_LSB[i]); + } + data->last_updated = jiffies; + data->valid = 1; + } + + mutex_unlock(&data->update_lock); + + return data; +} + +static ssize_t show_temp_value(struct device *dev, + struct device_attribute *devattr, char *buf) +{ + int index = to_sensor_dev_attr(devattr)->index; + struct tmp421_data *data = tmp421_update_device(dev); + int temp; + + mutex_lock(&data->update_lock); + if (data->config & TMP421_CONFIG_RANGE) + temp = temp_from_u16(data->temp[index]); + else + temp = temp_from_s16(data->temp[index]); + mutex_unlock(&data->update_lock); + + return sprintf(buf, "%d\n", temp); +} + +static ssize_t show_fault(struct device *dev, + struct device_attribute *devattr, char *buf) +{ + int index = to_sensor_dev_attr(devattr)->index; + struct tmp421_data *data = tmp421_update_device(dev); + + /* + * The OPEN bit signals a fault. This is bit 0 of the temperature + * register (low byte). + */ + if (data->temp[index] & 0x01) + return sprintf(buf, "1\n");
Review line 164
Quoted 10 lines
(quoted diff) +10
-0+ else + return sprintf(buf, "0\n"); +} + +static mode_t tmp421_is_visible(struct kobject *kobj, struct attribute *a, + int n) +{ + struct device *dev = container_of(kobj, struct device, kobj); + struct i2c_client *client = to_i2c_client(dev); + struct tmp421_data *data = i2c_get_clientdata(client);
If you don't need client for anything else, you can take a shortcut with data = dev_get_drvdata(dev).
Review line 172
Quoted 8 lines
(quoted diff) +8
-0+ struct device_attribute *devattr; + unsigned int index; + + devattr = container_of(a, struct device_attribute, attr); + index = to_sensor_dev_attr(devattr)->index; + + if (data->kind > index) + return a->mode;
This is still a little fragile IMHO, and might require a rework in the future.
Quoted 79 lines
(quoted diff) +79
-0+ + return 0; +} + +static SENSOR_DEVICE_ATTR(temp1_input, S_IRUGO, show_temp_value, NULL, 0); +static SENSOR_DEVICE_ATTR(temp2_input, S_IRUGO, show_temp_value, NULL, 1); +static SENSOR_DEVICE_ATTR(temp2_fault, S_IRUGO, show_fault, NULL, 1); +static SENSOR_DEVICE_ATTR(temp3_input, S_IRUGO, show_temp_value, NULL, 2); +static SENSOR_DEVICE_ATTR(temp3_fault, S_IRUGO, show_fault, NULL, 2); +static SENSOR_DEVICE_ATTR(temp4_input, S_IRUGO, show_temp_value, NULL, 3); +static SENSOR_DEVICE_ATTR(temp4_fault, S_IRUGO, show_fault, NULL, 3); + +static struct attribute *tmp421_attr[] = { + &sensor_dev_attr_temp1_input.dev_attr.attr, + &sensor_dev_attr_temp2_input.dev_attr.attr, + &sensor_dev_attr_temp2_fault.dev_attr.attr, + &sensor_dev_attr_temp3_input.dev_attr.attr, + &sensor_dev_attr_temp3_fault.dev_attr.attr, + &sensor_dev_attr_temp4_input.dev_attr.attr, + &sensor_dev_attr_temp4_fault.dev_attr.attr, + NULL +}; + +static const struct attribute_group tmp421_group = { + .attrs = tmp421_attr, + .is_visible = tmp421_is_visible, +}; + +static int tmp421_init_client(struct i2c_client *client) +{ + int config, config_orig; + + /* Set the conversion rate to 2 Hz */ + i2c_smbus_write_byte_data(client, TMP421_CONVERSION_RATE_REG, 0x05); + + /* Start conversions (disable shutdown if necessary) */ + config = i2c_smbus_read_byte_data(client, TMP421_CONFIG_REG_1); + if (config < 0) { + dev_err(&client->dev, "Could not read configuration" + " register (%d)\n", config); + return -ENODEV; + } + + config_orig = config; + config &= ~TMP421_CONFIG_SHUTDOWN; + + if (config != config_orig) { + dev_info(&client->dev, "Enable monitoring chip\n"); + i2c_smbus_write_byte_data(client, TMP421_CONFIG_REG_1, config); + } + + return 0; +} + +static int tmp421_detect(struct i2c_client *client, int kind, + struct i2c_board_info *info) +{ + struct i2c_adapter *adapter = client->adapter; + const char *names[] = { "TMP421", "TMP422", "TMP423" }; + + if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) + return -ENODEV; + + if (kind <= 0) { + u8 reg; + + reg = i2c_smbus_read_byte_data(client, + TMP421_MANUFACTURER_ID_REG); + if (reg != TMP421_MANUFACTURER_ID) + return -ENODEV; + + reg = i2c_smbus_read_byte_data(client, + TMP421_DEVICE_ID_REG); + switch (reg) { + case TMP421_DEVICE_ID: + kind = tmp421; + break; + case TMP422_DEVICE_ID: + kind = tmp422;
Review line 261
Quoted 10 lines
(quoted diff) +10
-0+ break; + case TMP423_DEVICE_ID: + kind = tmp423; + break; + default: + return -ENODEV; + } + } + strlcpy(info->type, tmp421_id[kind - 1].name, I2C_NAME_SIZE); + dev_info(&adapter->dev, "Detected TI %s chip\n", names[kind - 1]);
I suggest adding the address in the log message.
Review line 271
Quoted 10 lines
(quoted diff) +10
-0+ + return 0; +} + +static int tmp421_remove(struct i2c_client *client) +{ + struct tmp421_data *data = i2c_get_clientdata(client); + + if (data->hwmon_dev) + hwmon_device_unregister(data->hwmon_dev);
As you are no longer calling tmp421_remove() from tmp421_probe(), this test will always be successful.
Quoted 82 lines
(quoted diff) +78
-0+ + sysfs_remove_group(&client->dev.kobj, &tmp421_group); + + i2c_set_clientdata(client, NULL); + kfree(data); + + return 0; +} + +static int tmp421_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + struct tmp421_data *data; + int err; + + data = kzalloc(sizeof(struct tmp421_data), GFP_KERNEL); + if (!data) + return -ENOMEM; + + i2c_set_clientdata(client, data); + mutex_init(&data->update_lock); + data->kind = id->driver_data; + + err = tmp421_init_client(client); + if (err) + goto exit_free; + + err = sysfs_create_group(&client->dev.kobj, &tmp421_group); + if (err) + goto exit_free; + + data->hwmon_dev = hwmon_device_register(&client->dev); + if (IS_ERR(data->hwmon_dev)) { + err = PTR_ERR(data->hwmon_dev); + data->hwmon_dev = NULL; + goto exit_remove; + } + return 0; + +exit_remove: + sysfs_remove_group(&client->dev.kobj, &tmp421_group); + +exit_free: + i2c_set_clientdata(client, NULL); + kfree(data); + + return err; +} + +static struct i2c_driver tmp421_driver = { + .class = I2C_CLASS_HWMON, + .driver = { + .name = "tmp421", + }, + .probe = tmp421_probe, + .remove = tmp421_remove, + .id_table = tmp421_id, + .detect = tmp421_detect, + .address_data = &addr_data, +}; + +static int __init tmp421_init(void) +{ + return i2c_add_driver(&tmp421_driver); +} + +static void __exit tmp421_exit(void) +{ + i2c_del_driver(&tmp421_driver); +} + +MODULE_AUTHOR("Andre Prendel <[email protected]>"); +MODULE_DESCRIPTION("Texas Instruments TMP421/422/423 temperature sensor" + " driver"); +MODULE_LICENSE("GPL"); + +module_init(tmp421_init); +module_exit(tmp421_exit);Index: linux-2.6/drivers/hwmon/Kconfig
=================================> --- linux-2.6.orig/drivers/hwmon/Kconfig 2009-06-18 19:45:08.000000000 +0200
+++ linux-2.6/drivers/hwmon/Kconfig 2009-06-18 19:54:36.000000000 +0200
Review line 805
Quoted 9 lines
(quoted diff) +6
-0@@ -797,6 +797,16 @@ This driver can also be built as a module. If so, the module will be called tmp401. +config SENSORS_TMP421 + tristate "Texas Instruments TMP421, TMP422 and TMP423" + depends on I2C && EXPERIMENTAL + help + If you say yes here you get support for Texas Instruments TMP421 + temperature sensor chips.
... as well as TMP422 and TMP423.
Quoted 18 lines
(quoted diff) +4
-0+ + This driver can also be built as a module. If so, the module + will be called tmp421. + config SENSORS_VIA686A tristate "VIA686A" depends on PCIIndex: linux-2.6/drivers/hwmon/Makefile
=================================> --- linux-2.6.orig/drivers/hwmon/Makefile 2009-06-18 19:45:08.000000000 +0200
+++ linux-2.6/drivers/hwmon/Makefile 2009-06-18 19:54:36.000000000 +0200(quoted diff) +1
-0@@ -83,6 +83,7 @@ obj-$(CONFIG_SENSORS_SMSC47M192)+= smsc47m192.o obj-$(CONFIG_SENSORS_THMC50) += thmc50.o obj-$(CONFIG_SENSORS_TMP401) += tmp401.o +obj-$(CONFIG_SENSORS_TMP421) += tmp421.o obj-$(CONFIG_SENSORS_VIA686A) += via686a.o obj-$(CONFIG_SENSORS_VT1211) += vt1211.o obj-$(CONFIG_SENSORS_VT8231) += vt8231.o
Signature · 6 lines
Jean Delvare _______________________________________________ lm-sensors mailing list [email protected] http://lists.lm-sensors.org/mailman/listinfo/lm-sensors