Skip to contentSkip to conversation

for JEDEC flash, command of word programing should be issued relatvie to base

PATCH New Po-Yu Chuang 2 participants 4 messages Jul 7, 2009 – Jul 8, 2009 Memory technology devices (MTD)

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 for JEDEC flash, command of word programing should be issued relatvie to base

For JEDEC flash, we should issue word programming command relative to base address rather than sector base address. Original source makes SST Flash fails to program sectors which are not on the 0x10000 boundaries.

e.g.
SST39LF040 uses addr1=0x5555 and addr2=0x2AAA, however, each sector is 0x1000 bytes.

Thus, if we issue command to "sector base (0x41000) + offset(0x5555)", it sends to 0x46555 and the chip fails to recognize that address.

This patch is tested with SST39LF040.

---
 drivers/mtd/cfi_flash.c |   11 ++++++++---
 1 files changed, 8 insertions(+), 3 deletions(-)
drivers/mtd/cfi_flash.c +0 -0
index d0732f5..81ac5d3 100644
@@ -835,14 +835,19 @@ static int flash_write_cfiword (flash_info_t *

info, ulong dest,
break;
case CFI_CMDSET_AMD_EXTENDED:
case CFI_CMDSET_AMD_STANDARD:
-#ifdef CONFIG_FLASH_CFI_LEGACY
- case CFI_CMDSET_AMD_LEGACY:
-#endif
sect = find_sector(info, dest);
flash_unlock_seq (info, sect);
flash_write_cmd (info, sect, info->addr_unlock1, AMD_CMD_WRITE); sect_found = 1;
break;
+#ifdef CONFIG_FLASH_CFI_LEGACY
+ case CFI_CMDSET_AMD_LEGACY:
+ sect = find_sector(info, dest);
+ flash_unlock_seq (info, 0);
+ flash_write_cmd (info, 0, info->addr_unlock1, AMD_CMD_WRITE);
+ sect_found = 1;
+ break;
+#endif
}

switch (info->portwidth) {

Signature · 1 line
1.6.3.3
#1 lore raw

PATCH 1/1 for JEDEC flash, command of word programing should be issued relatvie to base

Quoted 8 lines · On Tuesday 07 July 2009 07:27:35 Po-Yu Chuang wrote:

For JEDEC flash, we should issue word programming command relative to base address rather than sector base address. Original source makes SST Flash fails to program sectors which are not on the 0x10000 boundaries.

e.g.
SST39LF040 uses addr1=0x5555 and addr2=0x2AAA, however, each sector is 0x1000 bytes.

Quoted 6 lines

Thus, if we issue command to "sector base (0x41000) + offset(0x5555)", it sends to 0x46555 and the chip fails to recognize that address.

This patch is tested with SST39LF040.

This patch is line wrapped and can't be applied. Please fix and resubmit. And while at it please use a somewhat shorted subject.

Thanks.

Best regards,
Stefan

=====================================================================
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office at denx.de
=====================================================================

#2 lore raw

PATCH 1/1 for JEDEC flash, command of word programing should be issued relatvie to base

Dear Stefan Roese,

2009/7/8 Stefan Roese <[email protected]>:

Quoted 2 lines

This patch is line wrapped and can't be applied. Please fix and resubmit. And while at it please use a somewhat shorted subject.

Sorry, I don't understand what does "line wrapped" mean. The source is 80 chars width max.
or... Did I send the mail in dos format?

regards,
Po-Yu Chuang

#3 lore raw

PATCH 1/1 for JEDEC flash, command of word programing should be issued relatvie to base

Quoted 6 lines · On Wednesday 08 July 2009 11:49:35 Po-Yu Chuang wrote:
Quoted 2 lines

This patch is line wrapped and can't be applied. Please fix and resubmit. And while at it please use a somewhat shorted subject.

Sorry, I don't understand what does "line wrapped" mean. The source is 80 chars width max.
or... Did I send the mail in dos format?

The problem is that you mail client wrapped too long lines into 2 lines. The patch can't be applied then anymore. Here a problematic line:

@ -835,14 +835,19 @@ static int flash_write_cfiword (flash_info_t * info, ulong dest,

This should be a single line. I suggest you send using git send-email.

Best regards,
Stefan

=====================================================================
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office at denx.de
=====================================================================