Skip to contentSkip to conversation

Add support for the KwikByte KBOC OMAP35xx board

PATCH New christian at kwikbyte.com 5 participants 15 messages Jul 9, 2009 – Jul 12, 2009 Kbuild

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 Add support for the KwikByte KBOC OMAP35xx board

Subject: [PATCH] Add support for the KwikByte KBOC OMAP35xx board

---
  MAINTAINERS                  |    4 +
  MAKEALL                      |    1 +
  Makefile                     |    3 +
  board/omap3/common/Makefile  |    1 +
  board/omap3/kboc/Makefile    |   49 ++++++
  board/omap3/kboc/config.mk   |   33 ++++
  board/omap3/kboc/kboc.c      |  106 ++++++++++++
  board/omap3/kboc/kboc.h      |  382  
++++++++++++++++++++++++++++++++++++++++++
  include/configs/omap3_kboc.h |  317 +++++++++++++++++++++++++++++++++++
  9 files changed, 896 insertions(+), 0 deletions(-)

create mode 100644 board/omap3/kboc/Makefile
create mode 100644 board/omap3/kboc/config.mk
create mode 100644 board/omap3/kboc/kboc.c
create mode 100644 board/omap3/kboc/kboc.h
create mode 100644 include/configs/omap3_kboc.h

MAINTAINERS +4 -0
index 0041112..cc55df9 100644
@@ -686,6 +686,10 @@ Alex Z
  	lart		SA1100
  	dnp1110		SA1110
 
+Christian Owens <[email protected]>
+
+	omap3_kboc	ARM CORTEX-A8 (OMAP35xx SoC)
+
  -------------------------------------------------------------------------
 
  Unknown / orphaned boards:
MAKEALL +1 -0
index 41f1445..ac0c5d9 100755
@@ -572,6 +572,7 @@ LIST_ARM_CORTEX_A8="		\
  	omap3_pandora		\
  	omap3_zoom1		\
  	omap3_zoom2		\
+	omap3_kboc		\
  "
 
  #########################################################################
Makefile +3 -0
index 2a06440..b204917 100644
@@ -3040,6 +3040,9 @@ omap3_zoom1_config :	unconfig
  omap3_zoom2_config :	unconfig
  	@$(MKCONFIG) $(@:_config=) arm arm_cortexa8 zoom2 omap3 omap3
 
+omap3_kboc_config :	unconfig
+	@$(MKCONFIG) $(@:_config=) arm arm_cortexa8 kboc omap3 omap3
+
  #########################################################################
  ## XScale Systems
  #########################################################################
board/omap3/common/Makefile +1 -0
index b8a0b14..4f7a20b 100644
@@ -34,6 +34,7 @@ COBJS-$(CONFIG_OMAP3_OVERO) += power.o
  COBJS-$(CONFIG_OMAP3_PANDORA) += power.o
  COBJS-$(CONFIG_OMAP3_ZOOM1) += power.o
  COBJS-$(CONFIG_OMAP3_ZOOM2) += power.o
+COBJS-$(CONFIG_OMAP3_KBOC) += power.o
 
  COBJS	:= $(COBJS-y)
  SRCS	:= $(COBJS:.o=.c)
board/omap3/kboc/Makefile new file +49 -0

49 lines not on this page · raw message

board/omap3/kboc/config.mk new file +33 -0
new file mode 100644
index 0000000..879b2e2
@@ -0,0 +1,33 @@
+#
+# (C) Copyright 2006
+# Texas Instruments, <www.ti.com>
+#
+# Beagle Board uses OMAP3 (ARM-CortexA8) cpu
+# see http://www.ti.com/ for more information on Texas Instruments
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+# Physical Address:
+# 8000'0000 (bank0)
+# A000/0000 (bank1)
+# Linux-Kernel is expected to be at 8000'8000, entry 8000'8000
+# (mem base + reserved)
+
+# For use with external or internal boots.
+TEXT_BASE = 0x80e80000
board/omap3/kboc/kboc.c new file +106 -0

106 lines not on this page · raw message

board/omap3/kboc/kboc.h new file +382 -0

382 lines not on this page · raw message

include/configs/omap3_kboc.h new file +317 -0

317 lines not on this page · raw message

Signature · 1 line
1.5.4.3
#1 lore raw

PATCH 1/1 Add support for the KwikByte KBOC OMAP35xx board

Quoted 1 line · On Thu, Jul 9, 2009 at 6:03 PM, <[email protected]> wrote:

Subject: [PATCH] Add support for the KwikByte KBOC OMAP35xx board

Do you have some link that you can point us to what is KwikByte KBOC board? give us some explanation..

Quoted 134 lines

---

?MAINTAINERS ? ? ? ? ? ? ? ? ?| ? ?4 +
?MAKEALL ? ? ? ? ? ? ? ? ? ? ?| ? ?1 +
?Makefile ? ? ? ? ? ? ? ? ? ? | ? ?3 +
?board/omap3/common/Makefile ?| ? ?1 +
?board/omap3/kboc/Makefile ? ?| ? 49 ++++++
?board/omap3/kboc/config.mk ? | ? 33 ++++
?board/omap3/kboc/kboc.c ? ? ?| ?106 ++++++++++++
?board/omap3/kboc/kboc.h ? ? ?| ?382

++++++++++++++++++++++++++++++++++++++++++
?include/configs/omap3_kboc.h | ?317 +++++++++++++++++++++++++++++++++++ ?9 files changed, 896 insertions(+), 0 deletions(-)
?create mode 100644 board/omap3/kboc/Makefile
?create mode 100644 board/omap3/kboc/config.mk
?create mode 100644 board/omap3/kboc/kboc.c
?create mode 100644 board/omap3/kboc/kboc.h
?create mode 100644 include/configs/omap3_kboc.h

MAINTAINERS +0 -0
index 0041112..cc55df9 100644
@@ -686,6 +686,10 @@ Alex Z

? ? ? ?lart ? ? ? ? ? ?SA1100
? ? ? ?dnp1110 ? ? ? ? SA1110

MAINTAINERS +4 -0
+Christian Owens <[email protected]>
+
+ ? ? ? omap3_kboc ? ? ?ARM CORTEX-A8 (OMAP35xx SoC)
+

?-------------------------------------------------------------------------

?Unknown / orphaned boards:

MAKEALL +1 -0
index 41f1445..ac0c5d9 100755
@@ -572,6 +572,7 @@ LIST_ARM_CORTEX_A8=" ? ? ? ? ? ? ? ?\
 ? ? ? ?omap3_pandora ? ? ? ? ? \
 ? ? ? ?omap3_zoom1 ? ? ? ? ? ? \
 ? ? ? ?omap3_zoom2 ? ? ? ? ? ? \
+ ? ? ? omap3_kboc ? ? ? ? ? ? ?\

?"

?#########################################################################

Makefile +0 -0
index 2a06440..b204917 100644
@@ -3040,6 +3040,9 @@ omap3_zoom1_config : ? ? ?unconfig

?omap3_zoom2_config : ?unconfig
? ? ? ?@$(MKCONFIG) $(@:_config=) arm arm_cortexa8 zoom2 omap3 omap3

Makefile +3 -0
+omap3_kboc_config : ? ?unconfig
+ ? ? ? @$(MKCONFIG) $(@:_config=) arm arm_cortexa8 kboc omap3 omap3
+

?######################################################################### ?## XScale Systems ?#########################################################################

board/omap3/common/Makefile +0 -0
index b8a0b14..4f7a20b 100644
@@ -34,6 +34,7 @@ COBJS-$(CONFIG_OMAP3_OVERO) += power.o

?COBJS-$(CONFIG_OMAP3_PANDORA) += power.o
?COBJS-$(CONFIG_OMAP3_ZOOM1) += power.o
?COBJS-$(CONFIG_OMAP3_ZOOM2) += power.o
+COBJS-$(CONFIG_OMAP3_KBOC) += power.o

?COBJS := $(COBJS-y)
?SRCS ?:= $(COBJS:.o=.c)

board/omap3/kboc/Makefile new file +49 -0
new file mode 100644
index 0000000..2c77444
@@ -0,0 +1,49 @@
+#
+# (C) Copyright 2000, 2001, 2002
+# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. ?See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB ? ?= $(obj)lib$(BOARD).a
+
+COBJS ?:= kboc.o
+
+SRCS ? := $(COBJS:.o=.c)
+OBJS ? := $(addprefix $(obj),$(COBJS))
+
+$(LIB): ? ? ? ?$(obj).depend $(OBJS)
+ ? ? ? $(AR) $(ARFLAGS) $@ $(OBJS)
+
+clean:
+ ? ? ? rm -f $(OBJS)
+
+distclean: ? ? clean
+ ? ? ? rm -f $(LIB) core *.bak $(obj).depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
board/omap3/kboc/config.mk new file +0 -0
new file mode 100644
index 0000000..879b2e2

board/omap3/kboc/config.mk line 6

Quoted 6 lines
board/omap3/kboc/config.mk new file +6 -0
@@ -0,0 +1,33 @@
+#
+# (C) Copyright 2006
+# Texas Instruments, <www.ti.com>
+#
+# Beagle Board uses OMAP3 (ARM-CortexA8) cpu
+# see http://www.ti.com/ for more information on Texas Instruments

is this board beagleboard? should this be here? mebbe you could take state copyrights right?

Quoted 33 lines
board/omap3/kboc/config.mk new file +27 -0
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. ?See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+# Physical Address:
+# 8000'0000 (bank0)
+# A000/0000 (bank1)
+# Linux-Kernel is expected to be at 8000'8000, entry 8000'8000
+# (mem base + reserved)
+
+# For use with external or internal boots.
+TEXT_BASE = 0x80e80000
board/omap3/kboc/kboc.c new file +0 -0
new file mode 100644
index 0000000..5fc9b96

board/omap3/kboc/kboc.c line 4

Quoted 4 lines
board/omap3/kboc/kboc.c new file +4 -0
@@ -0,0 +1,106 @@
+/*
+ * (C) Copyright 2009
+ * KwikByte <www.kwikbyte.com>
+ *

bit more info on the board is so useful for someone to read - remember you would be selling your board this way too.. give us more info and we can hopefully help..

Quoted 76 lines
board/omap3/kboc/kboc.c new file +76 -0
+ * Author :
+ * ?Christian Owens <[email protected]>
+ *
+ * Derived from the following:
+ *
+ * (C) Copyright 2004-2008
+ * Texas Instruments, <www.ti.com>
+ *
+ * Author :
+ * ? ? Sunil Kumar <[email protected]>
+ * ? ? Shashi Ranjan <[email protected]>
+ *
+ * Derived from Beagle Board and 3430 SDP code by
+ * ? ? Richard Woodruff <[email protected]>
+ * ? ? Syed Mohammed Khasim <[email protected]>
+ *
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. ?See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/mux.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/gpio.h>
+#include <asm/mach-types.h>
+#include "kboc.h"
+
+/*
+ * Routine: board_init
+ * Description: Early hardware init.
+ */
+int board_init(void)
+{
+ ? ? ? DECLARE_GLOBAL_DATA_PTR;
+
+ ? ? ? gpmc_init(); /* in SRAM or SDRAM, finish GPMC */
+ ? ? ? /* board id for Linux */
+ ? ? ? gd->bd->bi_arch_number = MACH_TYPE_OMAP3_KBOC;
+ ? ? ? /* boot param addr */
+ ? ? ? gd->bd->bi_boot_params = (OMAP34XX_SDRC_CS0 + 0x100);
+
+ ? ? ? return 0;
+}
+
+/*
+ * Routine: misc_init_r
+ * Description: Configure board specific parts
+ */
+int misc_init_r(void)
+{
+ ? ? ? gpio_t *gpio1_base = (gpio_t *)OMAP34XX_GPIO1_BASE;
+ ? ? ? gpio_t *gpio5_base = (gpio_t *)OMAP34XX_GPIO5_BASE;
+ ? ? ? gpio_t *gpio6_base = (gpio_t *)OMAP34XX_GPIO6_BASE;
+
+ ? ? ? power_init_r();
+
+ ? ? ? /* Configure GPIOs to output */
+ ? ? ? writel(~(GPIO23 | GPIO17 | GPIO12 | GPIO11 | GPIO10 | GPIO8 | GPIO2),
+ ? ? ? ? ? ? ? &gpio6_base->oe);
+ ? ? ? writel(~(GPIO31 | GPIO30 | GPIO29 | GPIO28 | GPIO22 | GPIO21 |

board/omap3/kboc/kboc.c

Quoted 10 lines
board/omap3/kboc/kboc.c new file +10 -0
+ ? ? ? ? ? ? ? GPIO13 | GPIO12), &gpio5_base->oe);
+ ? ? ? writel(~(GPIO22 | GPIO13), &gpio1_base->oe);
+
+ ? ? ? /* Set GPIOs */
+ ? ? ? writel(GPIO23 | GPIO17 | GPIO10 | GPIO8 | GPIO2,
+ ? ? ? ? ? ? ? &gpio6_base->setdataout);
+ ? ? ? writel(GPIO31 | GPIO29 | GPIO28 | GPIO22 | GPIO21 | GPIO13 | GPIO12,
+ ? ? ? ? ? ? ? &gpio5_base->setdataout);
+ ? ? ? writel(GPIO22 | GPIO13,
+ ? ? ? ? ? ? ? &gpio1_base->setdataout);

Aieeeee....... what are these gpios and why do they need to be set high?

normally you might want to do setdataout followed by oe?

Quoted 53 lines
board/omap3/kboc/kboc.c new file +16 -0
+
+ ? ? ? dieid_num_r();
+
+ ? ? ? return 0;
+}
+
+/*
+ * Routine: set_muxconf_regs
+ * Description: Setting up the configuration Mux registers specific to the
+ * ? ? ? ? ? ? hardware. Many pins need to be moved from protect to primary
+ * ? ? ? ? ? ? mode.
+ */
+void set_muxconf_regs(void)
+{
+ ? ? ? MUX_KBOC();
+}
board/omap3/kboc/kboc.h new file +31 -0
new file mode 100644
index 0000000..41c3b9e
@@ -0,0 +1,382 @@
+/*
+ * (C) Copyright 2009
+ * KwikByte <www.kwikbyte.com>
+ *
+ * Author :
+ * ?Christian Owens <[email protected]>
+ *
+ * Derived from the following:
+ *
+ * (C) Copyright 2008
+ * Dirk Behme <[email protected]>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. ?See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+#ifndef _KBOC_H_

board/omap3/kboc/kboc.h line 41

Quoted 10 lines
board/omap3/kboc/kboc.h new file +10 -0
+#define _KBOC_H_
+
+const omap3_sysinfo sysinfo = {
+ ? ? ? DDR_STACKED,
+ ? ? ? "OMAP3 KBOC board",
+#if defined(CONFIG_ENV_IS_IN_ONENAND)
+ ? ? ? "OneNAND",
+#else
+ ? ? ? "NAND",
+#endif

err... CONFIG_ENV_IS_IN_NAND is defined as 1 in config header.. means never support onenand?

Quoted 329 lines
board/omap3/kboc/kboc.h new file +329 -0
+};
+
+/*
+ * IEN ?- Input Enable
+ * IDIS - Input Disable
+ * PTD ?- Pull type Down
+ * PTU ?- Pull type Up
+ * DIS ?- Pull type selection is inactive
+ * EN ? - Pull type selection is active
+ * M0 ? - Mode 0
+ * The commented string gives the final mux configuration for that pin
+ */
+#define MUX_KBOC() \
+ /*SDRC*/\
+ MUX_VAL(CP(SDRC_D0), ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*SDRC_D0*/\
+ MUX_VAL(CP(SDRC_D1), ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*SDRC_D1*/\
+ MUX_VAL(CP(SDRC_D2), ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*SDRC_D2*/\
+ MUX_VAL(CP(SDRC_D3), ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*SDRC_D3*/\
+ MUX_VAL(CP(SDRC_D4), ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*SDRC_D4*/\
+ MUX_VAL(CP(SDRC_D5), ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*SDRC_D5*/\
+ MUX_VAL(CP(SDRC_D6), ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*SDRC_D6*/\
+ MUX_VAL(CP(SDRC_D7), ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*SDRC_D7*/\
+ MUX_VAL(CP(SDRC_D8), ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*SDRC_D8*/\
+ MUX_VAL(CP(SDRC_D9), ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*SDRC_D9*/\
+ MUX_VAL(CP(SDRC_D10), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*SDRC_D10*/\
+ MUX_VAL(CP(SDRC_D11), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*SDRC_D11*/\
+ MUX_VAL(CP(SDRC_D12), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*SDRC_D12*/\
+ MUX_VAL(CP(SDRC_D13), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*SDRC_D13*/\
+ MUX_VAL(CP(SDRC_D14), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*SDRC_D14*/\
+ MUX_VAL(CP(SDRC_D15), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*SDRC_D15*/\
+ MUX_VAL(CP(SDRC_D16), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*SDRC_D16*/\
+ MUX_VAL(CP(SDRC_D17), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*SDRC_D17*/\
+ MUX_VAL(CP(SDRC_D18), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*SDRC_D18*/\
+ MUX_VAL(CP(SDRC_D19), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*SDRC_D19*/\
+ MUX_VAL(CP(SDRC_D20), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*SDRC_D20*/\
+ MUX_VAL(CP(SDRC_D21), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*SDRC_D21*/\
+ MUX_VAL(CP(SDRC_D22), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*SDRC_D22*/\
+ MUX_VAL(CP(SDRC_D23), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*SDRC_D23*/\
+ MUX_VAL(CP(SDRC_D24), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*SDRC_D24*/\
+ MUX_VAL(CP(SDRC_D25), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*SDRC_D25*/\
+ MUX_VAL(CP(SDRC_D26), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*SDRC_D26*/\
+ MUX_VAL(CP(SDRC_D27), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*SDRC_D27*/\
+ MUX_VAL(CP(SDRC_D28), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*SDRC_D28*/\
+ MUX_VAL(CP(SDRC_D29), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*SDRC_D29*/\
+ MUX_VAL(CP(SDRC_D30), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*SDRC_D30*/\
+ MUX_VAL(CP(SDRC_D31), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*SDRC_D31*/\
+ MUX_VAL(CP(SDRC_CLK), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*SDRC_CLK*/\
+ MUX_VAL(CP(SDRC_DQS0), ? ? ? ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*SDRC_DQS0*/\
+ MUX_VAL(CP(SDRC_DQS1), ? ? ? ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*SDRC_DQS1*/\
+ MUX_VAL(CP(SDRC_DQS2), ? ? ? ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*SDRC_DQS2*/\
+ MUX_VAL(CP(SDRC_DQS3), ? ? ? ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*SDRC_DQS3*/\
+ /*GPMC*/\
+ MUX_VAL(CP(GPMC_A1), ? ? ? ? ?(IDIS | PTD | DIS | M0)) /*GPMC_A1*/\
+ MUX_VAL(CP(GPMC_A2), ? ? ? ? ?(IDIS | PTD | DIS | M0)) /*GPMC_A2*/\
+ MUX_VAL(CP(GPMC_A3), ? ? ? ? ?(IDIS | PTD | DIS | M0)) /*GPMC_A3*/\
+ MUX_VAL(CP(GPMC_A4), ? ? ? ? ?(IDIS | PTD | DIS | M0)) /*GPMC_A4*/\
+ MUX_VAL(CP(GPMC_A5), ? ? ? ? ?(IDIS | PTD | DIS | M0)) /*GPMC_A5*/\
+ MUX_VAL(CP(GPMC_A6), ? ? ? ? ?(IDIS | PTD | DIS | M0)) /*GPMC_A6*/\
+ MUX_VAL(CP(GPMC_A7), ? ? ? ? ?(IDIS | PTD | DIS | M0)) /*GPMC_A7*/\
+ MUX_VAL(CP(GPMC_A8), ? ? ? ? ?(IDIS | PTD | DIS | M0)) /*GPMC_A8*/\
+ MUX_VAL(CP(GPMC_A9), ? ? ? ? ?(IDIS | PTD | DIS | M0)) /*GPMC_A9*/\
+ MUX_VAL(CP(GPMC_A10), ? ? ? ? (IDIS | PTD | DIS | M0)) /*GPMC_A10*/\
+ MUX_VAL(CP(GPMC_D0), ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*GPMC_D0*/\
+ MUX_VAL(CP(GPMC_D1), ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*GPMC_D1*/\
+ MUX_VAL(CP(GPMC_D2), ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*GPMC_D2*/\
+ MUX_VAL(CP(GPMC_D3), ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*GPMC_D3*/\
+ MUX_VAL(CP(GPMC_D4), ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*GPMC_D4*/\
+ MUX_VAL(CP(GPMC_D5), ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*GPMC_D5*/\
+ MUX_VAL(CP(GPMC_D6), ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*GPMC_D6*/\
+ MUX_VAL(CP(GPMC_D7), ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*GPMC_D7*/\
+ MUX_VAL(CP(GPMC_D8), ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*GPMC_D8*/\
+ MUX_VAL(CP(GPMC_D9), ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*GPMC_D9*/\
+ MUX_VAL(CP(GPMC_D10), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*GPMC_D10*/\
+ MUX_VAL(CP(GPMC_D11), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*GPMC_D11*/\
+ MUX_VAL(CP(GPMC_D12), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*GPMC_D12*/\
+ MUX_VAL(CP(GPMC_D13), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*GPMC_D13*/\
+ MUX_VAL(CP(GPMC_D14), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*GPMC_D14*/\
+ MUX_VAL(CP(GPMC_D15), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*GPMC_D15*/\
+ MUX_VAL(CP(GPMC_NCS0), ? ? ? ? ? ? ? ?(IDIS | PTU | EN ?| M0)) /*GPMC_nCS0*/\
+ MUX_VAL(CP(GPMC_NCS1), ? ? ? ? ? ? ? ?(IDIS | PTU | EN ?| M0)) /*GPMC_nCS1*/\
+ MUX_VAL(CP(GPMC_NCS2), ? ? ? ? ? ? ? ?(IDIS | PTU | EN ?| M0)) /*GPMC_nCS2*/\
+ MUX_VAL(CP(GPMC_NCS3), ? ? ? ? ? ? ? ?(IDIS | PTU | EN ?| M0)) /*GPMC_nCS3*/\
+ MUX_VAL(CP(GPMC_NCS4), ? ? ? ? ? ? ? ?(IDIS | PTU | EN ?| M0)) /*GPMC_nCS4*/\
+ MUX_VAL(CP(GPMC_NCS5), ? ? ? ? ? ? ? ?(IDIS | PTD | DIS | M0)) /*GPMC_nCS5*/\
+ MUX_VAL(CP(GPMC_NCS6), ? ? ? ? ? ? ? ?(IEN ?| PTD | DIS | M1)) /*SYS_nDMA_REQ2*/\
+ MUX_VAL(CP(GPMC_NCS7), ? ? ? ? ? ? ? ?(IEN ?| PTU | EN ?| M1)) /*SYS_nDMA_REQ3*/\
+ MUX_VAL(CP(GPMC_NBE1), ? ? ? ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*GPMC_nBE1*/\
+ MUX_VAL(CP(GPMC_WAIT2), ? ? ? (IEN ?| PTU | EN ?| M0)) /*GPMC_WAIT2*/\
+ MUX_VAL(CP(GPMC_WAIT3), ? ? ? (IEN ?| PTU | EN ?| M0)) /*GPMC_WAIT3*/\
+ MUX_VAL(CP(GPMC_CLK), ? ? ? ? (IDIS | PTD | DIS | M0)) /*GPMC_CLK*/\
+ MUX_VAL(CP(GPMC_NADV_ALE), ? ?(IDIS | PTD | DIS | M0)) /*GPMC_nADV_ALE*/\
+ MUX_VAL(CP(GPMC_NOE), ? ? ? ? (IDIS | PTD | DIS | M0)) /*GPMC_nOE*/\
+ MUX_VAL(CP(GPMC_NWE), ? ? ? ? (IDIS | PTD | DIS | M0)) /*GPMC_nWE*/\
+ MUX_VAL(CP(GPMC_NBE0_CLE), ? ?(IDIS | PTD | DIS | M0)) /*GPMC_nBE0_CLE*/\
+ MUX_VAL(CP(GPMC_NWP), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*GPMC_nWP*/\
+ MUX_VAL(CP(GPMC_WAIT0), ? ? ? (IEN ?| PTU | EN ?| M0)) /*GPMC_WAIT0*/\
+ MUX_VAL(CP(GPMC_WAIT1), ? ? ? (IEN ?| PTU | EN ?| M0)) /*GPMC_WAIT1*/\
+ /*DSS*/\
+ MUX_VAL(CP(DSS_PCLK), ? ? ? ? (IDIS | PTD | DIS | M0)) /*DSS_PCLK*/\
+ MUX_VAL(CP(DSS_HSYNC), ? ? ? ? ? ? ? ?(IDIS | PTD | DIS | M0)) /*DSS_HSYNC*/\
+ MUX_VAL(CP(DSS_VSYNC), ? ? ? ? ? ? ? ?(IDIS | PTD | DIS | M0)) /*DSS_VSYNC*/\
+ MUX_VAL(CP(DSS_ACBIAS), ? ? ? (IDIS | PTD | DIS | M0)) /*DSS_ACBIAS*/\
+ MUX_VAL(CP(DSS_DATA0), ? ? ? ? ? ? ? ?(IDIS | PTD | DIS | M0)) /*DSS_DATA0*/\
+ MUX_VAL(CP(DSS_DATA1), ? ? ? ? ? ? ? ?(IDIS | PTD | DIS | M0)) /*DSS_DATA1*/\
+ MUX_VAL(CP(DSS_DATA2), ? ? ? ? ? ? ? ?(IDIS | PTD | DIS | M0)) /*DSS_DATA2*/\
+ MUX_VAL(CP(DSS_DATA3), ? ? ? ? ? ? ? ?(IDIS | PTD | DIS | M0)) /*DSS_DATA3*/\
+ MUX_VAL(CP(DSS_DATA4), ? ? ? ? ? ? ? ?(IDIS | PTD | DIS | M0)) /*DSS_DATA4*/\
+ MUX_VAL(CP(DSS_DATA5), ? ? ? ? ? ? ? ?(IDIS | PTD | DIS | M0)) /*DSS_DATA5*/\
+ MUX_VAL(CP(DSS_DATA6), ? ? ? ? ? ? ? ?(IDIS | PTD | DIS | M0)) /*DSS_DATA6*/\
+ MUX_VAL(CP(DSS_DATA7), ? ? ? ? ? ? ? ?(IDIS | PTD | DIS | M0)) /*DSS_DATA7*/\
+ MUX_VAL(CP(DSS_DATA8), ? ? ? ? ? ? ? ?(IDIS | PTD | DIS | M0)) /*DSS_DATA8*/\
+ MUX_VAL(CP(DSS_DATA9), ? ? ? ? ? ? ? ?(IDIS | PTD | DIS | M0)) /*DSS_DATA9*/\
+ MUX_VAL(CP(DSS_DATA10), ? ? ? (IDIS | PTD | DIS | M0)) /*DSS_DATA10*/\
+ MUX_VAL(CP(DSS_DATA11), ? ? ? (IDIS | PTD | DIS | M0)) /*DSS_DATA11*/\
+ MUX_VAL(CP(DSS_DATA12), ? ? ? (IDIS | PTD | DIS | M0)) /*DSS_DATA12*/\
+ MUX_VAL(CP(DSS_DATA13), ? ? ? (IDIS | PTD | DIS | M0)) /*DSS_DATA13*/\
+ MUX_VAL(CP(DSS_DATA14), ? ? ? (IDIS | PTD | DIS | M0)) /*DSS_DATA14*/\
+ MUX_VAL(CP(DSS_DATA15), ? ? ? (IDIS | PTD | DIS | M0)) /*DSS_DATA15*/\
+ MUX_VAL(CP(DSS_DATA16), ? ? ? (IDIS | PTD | DIS | M0)) /*DSS_DATA16*/\
+ MUX_VAL(CP(DSS_DATA17), ? ? ? (IDIS | PTD | DIS | M0)) /*DSS_DATA17*/\
+ MUX_VAL(CP(DSS_DATA18), ? ? ? (IDIS | PTD | DIS | M0)) /*DSS_DATA18*/\
+ MUX_VAL(CP(DSS_DATA19), ? ? ? (IDIS | PTD | DIS | M0)) /*DSS_DATA19*/\
+ MUX_VAL(CP(DSS_DATA20), ? ? ? (IDIS | PTD | DIS | M0)) /*DSS_DATA20*/\
+ MUX_VAL(CP(DSS_DATA21), ? ? ? (IDIS | PTD | DIS | M0)) /*DSS_DATA21*/\
+ MUX_VAL(CP(DSS_DATA22), ? ? ? (IDIS | PTD | DIS | M0)) /*DSS_DATA22*/\
+ MUX_VAL(CP(DSS_DATA23), ? ? ? (IDIS | PTD | DIS | M0)) /*DSS_DATA23*/\
+ /*CAMERA*/\
+ MUX_VAL(CP(CAM_HS), ? ? ? ? ? (IEN ?| PTU | EN ?| M0)) /*CAM_HS */\
+ MUX_VAL(CP(CAM_VS), ? ? ? ? ? (IEN ?| PTU | EN ?| M0)) /*CAM_VS */\
+ MUX_VAL(CP(CAM_XCLKA), ? ? ? ? ? ? ? ?(IDIS | PTD | DIS | M0)) /*CAM_XCLKA*/\
+ MUX_VAL(CP(CAM_PCLK), ? ? ? ? (IEN ?| PTU | EN ?| M0)) /*CAM_PCLK*/\
+ MUX_VAL(CP(CAM_FLD), ? ? ? ? ?(IDIS | PTD | DIS | M4)) /*GPIO_98*/\
+ MUX_VAL(CP(CAM_D0), ? ? ? ? ? (IEN ?| PTD | DIS | M0)) /*CAM_D0*/\
+ MUX_VAL(CP(CAM_D1), ? ? ? ? ? (IEN ?| PTD | DIS | M0)) /*CAM_D1*/\
+ MUX_VAL(CP(CAM_D2), ? ? ? ? ? (IEN ?| PTD | DIS | M0)) /*CAM_D2*/\
+ MUX_VAL(CP(CAM_D3), ? ? ? ? ? (IEN ?| PTD | DIS | M0)) /*CAM_D3*/\
+ MUX_VAL(CP(CAM_D4), ? ? ? ? ? (IEN ?| PTD | DIS | M0)) /*CAM_D4*/\
+ MUX_VAL(CP(CAM_D5), ? ? ? ? ? (IEN ?| PTD | DIS | M0)) /*CAM_D5*/\
+ MUX_VAL(CP(CAM_D6), ? ? ? ? ? (IEN ?| PTD | DIS | M0)) /*CAM_D6*/\
+ MUX_VAL(CP(CAM_D7), ? ? ? ? ? (IEN ?| PTD | DIS | M0)) /*CAM_D7*/\
+ MUX_VAL(CP(CAM_D8), ? ? ? ? ? (IEN ?| PTD | DIS | M0)) /*CAM_D8*/\
+ MUX_VAL(CP(CAM_D9), ? ? ? ? ? (IEN ?| PTD | DIS | M0)) /*CAM_D9*/\
+ MUX_VAL(CP(CAM_D10), ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*CAM_D10*/\
+ MUX_VAL(CP(CAM_D11), ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*CAM_D11*/\
+ MUX_VAL(CP(CAM_XCLKB), ? ? ? ? ? ? ? ?(IDIS | PTD | DIS | M0)) /*CAM_XCLKB*/\
+ MUX_VAL(CP(CAM_WEN), ? ? ? ? ?(IEN ?| PTD | DIS | M4)) /*GPIO_167*/\
+ MUX_VAL(CP(CAM_STROBE), ? ? ? (IDIS | PTD | DIS | M0)) /*CAM_STROBE*/\
+ MUX_VAL(CP(CSI2_DX0), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*CSI2_DX0*/\
+ MUX_VAL(CP(CSI2_DY0), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*CSI2_DY0*/\
+ MUX_VAL(CP(CSI2_DX1), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*CSI2_DX1*/\
+ MUX_VAL(CP(CSI2_DY1), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*CSI2_DY1*/\
+ /*Audio Interface */\
+ MUX_VAL(CP(MCBSP2_FSX), ? ? ? (IEN ?| PTD | DIS | M0)) /*McBSP2_FSX*/\
+ MUX_VAL(CP(MCBSP2_CLKX), ? ? ?(IEN ?| PTD | DIS | M0)) /*McBSP2_CLKX*/\
+ MUX_VAL(CP(MCBSP2_DR), ? ? ? ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*McBSP2_DR*/\
+ MUX_VAL(CP(MCBSP2_DX), ? ? ? ? ? ? ? ?(IDIS | PTD | DIS | M0)) /*McBSP2_DX*/\
+ /*Expansion card */\
+ MUX_VAL(CP(MMC1_CLK), ? ? ? ? (IDIS | PTU | EN ?| M0)) /*MMC1_CLK*/\
+ MUX_VAL(CP(MMC1_CMD), ? ? ? ? (IEN ?| PTU | EN ?| M0)) /*MMC1_CMD*/\
+ MUX_VAL(CP(MMC1_DAT0), ? ? ? ? ? ? ? ?(IEN ?| PTU | EN ?| M0)) /*MMC1_DAT0*/\
+ MUX_VAL(CP(MMC1_DAT1), ? ? ? ? ? ? ? ?(IEN ?| PTU | EN ?| M0)) /*MMC1_DAT1*/\
+ MUX_VAL(CP(MMC1_DAT2), ? ? ? ? ? ? ? ?(IEN ?| PTU | EN ?| M0)) /*MMC1_DAT2*/\
+ MUX_VAL(CP(MMC1_DAT3), ? ? ? ? ? ? ? ?(IEN ?| PTU | EN ?| M0)) /*MMC1_DAT3*/\
+ MUX_VAL(CP(MMC1_DAT4), ? ? ? ? ? ? ? ?(IEN ?| PTU | EN ?| M0)) /*MMC1_DAT4*/\
+ MUX_VAL(CP(MMC1_DAT5), ? ? ? ? ? ? ? ?(IEN ?| PTU | EN ?| M0)) /*MMC1_DAT5*/\
+ MUX_VAL(CP(MMC1_DAT6), ? ? ? ? ? ? ? ?(IEN ?| PTU | EN ?| M0)) /*MMC1_DAT6*/\
+ MUX_VAL(CP(MMC1_DAT7), ? ? ? ? ? ? ? ?(IEN ?| PTU | EN ?| M0)) /*MMC1_DAT7*/\
+ /*Wireless LAN */\
+ MUX_VAL(CP(MMC2_CLK), ? ? ? ? (IEN ?| PTU | EN ?| M4)) /*GPIO_130*/\
+ MUX_VAL(CP(MMC2_CMD), ? ? ? ? (IEN ?| PTU | EN ?| M4)) /*GPIO_131*/\
+ MUX_VAL(CP(MMC2_DAT0), ? ? ? ? ? ? ? ?(IEN ?| PTU | EN ?| M4)) /*GPIO_132*/\
+ MUX_VAL(CP(MMC2_DAT1), ? ? ? ? ? ? ? ?(IEN ?| PTU | EN ?| M4)) /*GPIO_133*/\
+ MUX_VAL(CP(MMC2_DAT2), ? ? ? ? ? ? ? ?(IEN ?| PTU | EN ?| M4)) /*GPIO_134*/\
+ MUX_VAL(CP(MMC2_DAT3), ? ? ? ? ? ? ? ?(IEN ?| PTU | EN ?| M4)) /*GPIO_135*/\
+ MUX_VAL(CP(MMC2_DAT4), ? ? ? ? ? ? ? ?(IEN ?| PTU | EN ?| M4)) /*GPIO_136*/\
+ MUX_VAL(CP(MMC2_DAT5), ? ? ? ? ? ? ? ?(IEN ?| PTU | EN ?| M4)) /*GPIO_137*/\
+ MUX_VAL(CP(MMC2_DAT6), ? ? ? ? ? ? ? ?(IEN ?| PTU | EN ?| M4)) /*GPIO_138*/\
+ MUX_VAL(CP(MMC2_DAT7), ? ? ? ? ? ? ? ?(IEN ?| PTU | EN ?| M4)) /*GPIO_139*/\
+ /*Bluetooth*/\
+ MUX_VAL(CP(MCBSP3_DX), ? ? ? ? ? ? ? ?(IEN ?| PTD | DIS | M1)) /*UART2_CTS*/\
+ MUX_VAL(CP(MCBSP3_DR), ? ? ? ? ? ? ? ?(IDIS | PTD | DIS | M1)) /*UART2_RTS*/\
+ MUX_VAL(CP(MCBSP3_CLKX), ? ? ?(IDIS | PTD | DIS | M1)) /*UART2_TX*/\
+ MUX_VAL(CP(MCBSP3_FSX), ? ? ? (IEN ?| PTD | DIS | M1)) /*UART2_RX*/\
+ MUX_VAL(CP(UART2_CTS), ? ? ? ? ? ? ? ?(IEN ?| PTD | DIS | M4)) /*GPIO_144*/\
+ MUX_VAL(CP(UART2_RTS), ? ? ? ? ? ? ? ?(IEN ?| PTD | DIS | M4)) /*GPIO_145*/\
+ MUX_VAL(CP(UART2_TX), ? ? ? ? (IEN ?| PTD | DIS | M4)) /*GPIO_146*/\
+ MUX_VAL(CP(UART2_RX), ? ? ? ? (IEN ?| PTD | DIS | M4)) /*GPIO_147*/\
+ /*Modem Interface */\
+ MUX_VAL(CP(UART1_TX), ? ? ? ? (IDIS | PTD | DIS | M0)) /*UART1_TX*/\
+ MUX_VAL(CP(UART1_RTS), ? ? ? ? ? ? ? ?(IDIS | PTD | DIS | M4)) /*GPIO_149*/ \
+ MUX_VAL(CP(UART1_CTS), ? ? ? ? ? ? ? ?(IDIS | PTD | DIS | M4)) /*GPIO_150*/ \
+ MUX_VAL(CP(UART1_RX), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*UART1_RX*/\
+ MUX_VAL(CP(MCBSP4_CLKX), ? ? ?(IEN ?| PTD | DIS | M1)) /*SSI1_DAT_RX*/\
+ MUX_VAL(CP(MCBSP4_DR), ? ? ? ? ? ? ? ?(IEN ?| PTD | DIS | M1)) /*SSI1_FLAG_RX*/\
+ MUX_VAL(CP(MCBSP4_DX), ? ? ? ? ? ? ? ?(IEN ?| PTD | DIS | M1)) /*SSI1_RDY_RX*/\
+ MUX_VAL(CP(MCBSP4_FSX), ? ? ? (IEN ?| PTD | DIS | M1)) /*SSI1_WAKE*/\
+ MUX_VAL(CP(MCBSP1_CLKR), ? ? ?(IDIS | PTU | EN ?| M4)) /*GPIO_156*/\
+ MUX_VAL(CP(MCBSP1_FSR), ? ? ? (IDIS | PTU | EN ?| M4)) /*GPIO_157*/\
+ MUX_VAL(CP(MCBSP1_DX), ? ? ? ? ? ? ? ?(IDIS | PTD | EN ?| M4)) /*GPIO_158*/\
+ MUX_VAL(CP(MCBSP1_DR), ? ? ? ? ? ? ? ?(IDIS | PTU | EN ?| M4)) /*GPIO_159*/\
+ MUX_VAL(CP(MCBSP_CLKS), ? ? ? (IEN ?| PTU | DIS | M0)) /*McBSP_CLKS*/\
+ MUX_VAL(CP(MCBSP1_FSX), ? ? ? (IEN ?| PTD | DIS | M4)) /*GPIO_161*/\
+ MUX_VAL(CP(MCBSP1_CLKX), ? ? ?(IDIS | PTD | DIS | M4)) /*GPIO_162*/\
+ /*Serial Interface*/\
+ MUX_VAL(CP(UART3_CTS_RCTX), ? (IEN ?| PTD | EN ?| M0)) /*UART3_CTS_RCTX*/\
+ MUX_VAL(CP(UART3_RTS_SD), ? ? (IDIS | PTD | DIS | M0)) /*UART3_RTS_SD */\
+ MUX_VAL(CP(UART3_RX_IRRX), ? ?(IEN ?| PTD | DIS | M0)) /*UART3_RX_IRRX*/\
+ MUX_VAL(CP(UART3_TX_IRTX), ? ?(IDIS | PTD | DIS | M0)) /*UART3_TX_IRTX*/\
+ MUX_VAL(CP(HSUSB0_CLK), ? ? ? (IEN ?| PTD | DIS | M0)) /*HSUSB0_CLK*/\
+ MUX_VAL(CP(HSUSB0_STP), ? ? ? (IDIS | PTU | EN ?| M0)) /*HSUSB0_STP*/\
+ MUX_VAL(CP(HSUSB0_DIR), ? ? ? (IEN ?| PTD | DIS | M0)) /*HSUSB0_DIR*/\
+ MUX_VAL(CP(HSUSB0_NXT), ? ? ? (IEN ?| PTD | DIS | M0)) /*HSUSB0_NXT*/\
+ MUX_VAL(CP(HSUSB0_DATA0), ? ? (IEN ?| PTD | DIS | M0)) /*HSUSB0_DATA0*/\
+ MUX_VAL(CP(HSUSB0_DATA1), ? ? (IEN ?| PTD | DIS | M0)) /*HSUSB0_DATA1*/\
+ MUX_VAL(CP(HSUSB0_DATA2), ? ? (IEN ?| PTD | DIS | M0)) /*HSUSB0_DATA2*/\
+ MUX_VAL(CP(HSUSB0_DATA3), ? ? (IEN ?| PTD | DIS | M0)) /*HSUSB0_DATA3*/\
+ MUX_VAL(CP(HSUSB0_DATA4), ? ? (IEN ?| PTD | DIS | M0)) /*HSUSB0_DATA4*/\
+ MUX_VAL(CP(HSUSB0_DATA5), ? ? (IEN ?| PTD | DIS | M0)) /*HSUSB0_DATA5*/\
+ MUX_VAL(CP(HSUSB0_DATA6), ? ? (IEN ?| PTD | DIS | M0)) /*HSUSB0_DATA6*/\
+ MUX_VAL(CP(HSUSB0_DATA7), ? ? (IEN ?| PTD | DIS | M0)) /*HSUSB0_DATA7*/\
+ MUX_VAL(CP(I2C1_SCL), ? ? ? ? (IEN ?| PTU | EN ?| M0)) /*I2C1_SCL*/\
+ MUX_VAL(CP(I2C1_SDA), ? ? ? ? (IEN ?| PTU | EN ?| M0)) /*I2C1_SDA*/\
+ MUX_VAL(CP(I2C2_SCL), ? ? ? ? (IEN ?| PTU | EN ?| M4)) /*GPIO_168*/\
+ MUX_VAL(CP(I2C2_SDA), ? ? ? ? (IEN ?| PTU | EN ?| M4)) /*GPIO_183*/\
+ MUX_VAL(CP(I2C3_SCL), ? ? ? ? (IEN ?| PTU | EN ?| M0)) /*I2C3_SCL*/\
+ MUX_VAL(CP(I2C3_SDA), ? ? ? ? (IEN ?| PTU | EN ?| M0)) /*I2C3_SDA*/\
+ MUX_VAL(CP(I2C4_SCL), ? ? ? ? (IEN ?| PTU | EN ?| M0)) /*I2C4_SCL*/\
+ MUX_VAL(CP(I2C4_SDA), ? ? ? ? (IEN ?| PTU | EN ?| M0)) /*I2C4_SDA*/\
+ MUX_VAL(CP(HDQ_SIO), ? ? ? ? ?(IDIS | PTU | EN ?| M4)) /*GPIO_170*/\
+ MUX_VAL(CP(MCSPI1_CLK), ? ? ? (IDIS | PTU | EN ?| M0)) /*SPI1_CLK*/\
+ MUX_VAL(CP(MCSPI1_SIMO), ? ? ?(IDIS | PTU | DIS | M0)) /*SPI1_SIMO*/\
+ MUX_VAL(CP(MCSPI1_SOMI), ? ? ?(IEN ?| PTD | DIS | M0)) /*McSPI1_SOMI*/\
+ MUX_VAL(CP(MCSPI1_CS0), ? ? ? (IEN ?| PTD | EN ?| M0)) /*McSPI1_CS0*/\
+ MUX_VAL(CP(MCSPI1_CS1), ? ? ? (IDIS | PTD | EN ?| M0)) /*McSPI1_CS1*/\
+ MUX_VAL(CP(MCSPI1_CS2), ? ? ? (IDIS | PTD | DIS | M4)) /*GPIO_176*/\
+ /* USB EHCI (port 2) */\
+ MUX_VAL(CP(MCSPI1_CS3), ? ? ? (IDIS | PTU | EN ?| M0)) /*SPI1_CS3*/\
+ MUX_VAL(CP(MCSPI2_CLK), ? ? ? (IEN ?| PTU | DIS | M3)) /*HSUSB2_DATA7*/\
+ MUX_VAL(CP(MCSPI2_SIMO), ? ? ?(IEN ?| PTU | DIS | M3)) /*HSUSB2_DATA4*/\
+ MUX_VAL(CP(MCSPI2_SOMI), ? ? ?(IEN ?| PTU | DIS | M3)) /*HSUSB2_DATA5*/\
+ MUX_VAL(CP(MCSPI2_CS0), ? ? ? (IEN ?| PTU | DIS | M3)) /*HSUSB2_DATA6*/\
+ MUX_VAL(CP(MCSPI2_CS1), ? ? ? (IEN ?| PTU | DIS | M3)) /*HSUSB2_DATA3*/\
+ MUX_VAL(CP(ETK_D10_ES2), ? ? ?(IDIS | PTU | DIS | M3)) /*HSUSB2_CLK*/\
+ MUX_VAL(CP(ETK_D11_ES2), ? ? ?(IDIS | PTU | DIS | M3)) /*HSUSB2_STP*/\
+ MUX_VAL(CP(ETK_D12_ES2), ? ? ?(IEN ?| PTU | DIS | M3)) /*HSUSB2_DIR*/\
+ MUX_VAL(CP(ETK_D13_ES2), ? ? ?(IEN ?| PTU | DIS | M3)) /*HSUSB2_NXT*/\
+ MUX_VAL(CP(ETK_D14_ES2), ? ? ?(IEN ?| PTU | DIS | M3)) /*HSUSB2_DATA0*/\
+ MUX_VAL(CP(ETK_D15_ES2), ? ? ?(IEN ?| PTU | DIS | M3)) /*HSUSB2_DATA1*/\
+ /*Control and debug */\
+ MUX_VAL(CP(SYS_32K), ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*SYS_32K*/\
+ MUX_VAL(CP(SYS_CLKREQ), ? ? ? (IEN ?| PTD | DIS | M0)) /*SYS_CLKREQ*/\
+ MUX_VAL(CP(SYS_NIRQ), ? ? ? ? (IEN ?| PTU | EN ?| M0)) /*SYS_nIRQ*/\
+ MUX_VAL(CP(SYS_BOOT0), ? ? ? ? ? ? ? ?(IEN ?| PTD | DIS | M4)) /*GPIO_2*/\
+ MUX_VAL(CP(SYS_BOOT1), ? ? ? ? ? ? ? ?(IEN ?| PTD | DIS | M4)) /*GPIO_3*/\
+ MUX_VAL(CP(SYS_BOOT2), ? ? ? ? ? ? ? ?(IEN ?| PTD | DIS | M4)) /*GPIO_4 - MMC1_WP*/\
+ MUX_VAL(CP(SYS_BOOT3), ? ? ? ? ? ? ? ?(IEN ?| PTD | DIS | M4)) /*GPIO_5*/\
+ MUX_VAL(CP(SYS_BOOT4), ? ? ? ? ? ? ? ?(IEN ?| PTD | DIS | M4)) /*GPIO_6*/\
+ MUX_VAL(CP(SYS_BOOT5), ? ? ? ? ? ? ? ?(IEN ?| PTD | DIS | M4)) /*GPIO_7*/\
+ MUX_VAL(CP(SYS_BOOT6), ? ? ? ? ? ? ? ?(IDIS | PTD | DIS | M4)) /*GPIO_8*/ \
+ MUX_VAL(CP(SYS_OFF_MODE), ? ? (IEN ?| PTD | DIS | M0)) /*SYS_OFF_MODE*/\
+ MUX_VAL(CP(SYS_CLKOUT1), ? ? ?(IEN ?| PTD | DIS | M0)) /*SYS_CLKOUT1*/\
+ MUX_VAL(CP(SYS_CLKOUT2), ? ? ?(IEN ?| PTU | EN ?| M4)) /*GPIO_186*/\
+ MUX_VAL(CP(ETK_CLK_ES2), ? ? ?(IDIS | PTU | EN ?| M3)) /*HSUSB1_STP*/\
+ MUX_VAL(CP(ETK_CTL_ES2), ? ? ?(IDIS | PTU | EN ?| M4)) /*GPIO_13*/\
+ MUX_VAL(CP(ETK_D0_ES2), ? ? ? (IEN ?| PTU | DIS | M3)) /*HSUSB1_DATA0*/\
+ MUX_VAL(CP(ETK_D1_ES2), ? ? ? (IEN ?| PTU | DIS | M3)) /*HSUSB1_DATA1*/\
+ MUX_VAL(CP(ETK_D2_ES2), ? ? ? (IEN ?| PTU | DIS | M3)) /*HSUSB1_DATA2*/\
+ MUX_VAL(CP(ETK_D3_ES2), ? ? ? (IEN ?| PTU | DIS | M3)) /*HSUSB1_DATA7*/\
+ MUX_VAL(CP(ETK_D4_ES2), ? ? ? (IEN ?| PTU | DIS | M3)) /*HSUSB1_DATA4*/\
+ MUX_VAL(CP(ETK_D5_ES2), ? ? ? (IEN ?| PTU | DIS | M3)) /*HSUSB1_DATA5*/\
+ MUX_VAL(CP(ETK_D6_ES2), ? ? ? (IEN ?| PTU | DIS | M3)) /*HSUSB1_DATA6*/\
+ MUX_VAL(CP(ETK_D7_ES2), ? ? ? (IEN ?| PTU | DIS | M3)) /*HSUSB1_DATA3*/\
+ MUX_VAL(CP(ETK_D8_ES2), ? ? ? (IDIS | PTU | EN ?| M4)) /*GPIO_22*/\
+ MUX_VAL(CP(ETK_D9_ES2), ? ? ? (IEN ?| PTU | DIS | M3)) /*HSUSB1_NXT*/\
+ MUX_VAL(CP(D2D_MCAD1), ? ? ? ? ? ? ? ?(IEN ?| PTD | EN ?| M0)) /*d2d_mcad1*/\
+ MUX_VAL(CP(D2D_MCAD2), ? ? ? ? ? ? ? ?(IEN ?| PTD | EN ?| M0)) /*d2d_mcad2*/\
+ MUX_VAL(CP(D2D_MCAD3), ? ? ? ? ? ? ? ?(IEN ?| PTD | EN ?| M0)) /*d2d_mcad3*/\
+ MUX_VAL(CP(D2D_MCAD4), ? ? ? ? ? ? ? ?(IEN ?| PTD | EN ?| M0)) /*d2d_mcad4*/\
+ MUX_VAL(CP(D2D_MCAD5), ? ? ? ? ? ? ? ?(IEN ?| PTD | EN ?| M0)) /*d2d_mcad5*/\
+ MUX_VAL(CP(D2D_MCAD6), ? ? ? ? ? ? ? ?(IEN ?| PTD | EN ?| M0)) /*d2d_mcad6*/\
+ MUX_VAL(CP(D2D_MCAD7), ? ? ? ? ? ? ? ?(IEN ?| PTD | EN ?| M0)) /*d2d_mcad7*/\
+ MUX_VAL(CP(D2D_MCAD8), ? ? ? ? ? ? ? ?(IEN ?| PTD | EN ?| M0)) /*d2d_mcad8*/\
+ MUX_VAL(CP(D2D_MCAD9), ? ? ? ? ? ? ? ?(IEN ?| PTD | EN ?| M0)) /*d2d_mcad9*/\
+ MUX_VAL(CP(D2D_MCAD10), ? ? ? (IEN ?| PTD | EN ?| M0)) /*d2d_mcad10*/\
+ MUX_VAL(CP(D2D_MCAD11), ? ? ? (IEN ?| PTD | EN ?| M0)) /*d2d_mcad11*/\
+ MUX_VAL(CP(D2D_MCAD12), ? ? ? (IEN ?| PTD | EN ?| M0)) /*d2d_mcad12*/\
+ MUX_VAL(CP(D2D_MCAD13), ? ? ? (IEN ?| PTD | EN ?| M0)) /*d2d_mcad13*/\
+ MUX_VAL(CP(D2D_MCAD14), ? ? ? (IEN ?| PTD | EN ?| M0)) /*d2d_mcad14*/\
+ MUX_VAL(CP(D2D_MCAD15), ? ? ? (IEN ?| PTD | EN ?| M0)) /*d2d_mcad15*/\
+ MUX_VAL(CP(D2D_MCAD16), ? ? ? (IEN ?| PTD | EN ?| M0)) /*d2d_mcad16*/\
+ MUX_VAL(CP(D2D_MCAD17), ? ? ? (IEN ?| PTD | EN ?| M0)) /*d2d_mcad17*/\
+ MUX_VAL(CP(D2D_MCAD18), ? ? ? (IEN ?| PTD | EN ?| M0)) /*d2d_mcad18*/\
+ MUX_VAL(CP(D2D_MCAD19), ? ? ? (IEN ?| PTD | EN ?| M0)) /*d2d_mcad19*/\
+ MUX_VAL(CP(D2D_MCAD20), ? ? ? (IEN ?| PTD | EN ?| M0)) /*d2d_mcad20*/\
+ MUX_VAL(CP(D2D_MCAD21), ? ? ? (IEN ?| PTD | EN ?| M0)) /*d2d_mcad21*/\
+ MUX_VAL(CP(D2D_MCAD22), ? ? ? (IEN ?| PTD | EN ?| M0)) /*d2d_mcad22*/\
+ MUX_VAL(CP(D2D_MCAD23), ? ? ? (IEN ?| PTD | EN ?| M0)) /*d2d_mcad23*/\
+ MUX_VAL(CP(D2D_MCAD24), ? ? ? (IEN ?| PTD | EN ?| M0)) /*d2d_mcad24*/\
+ MUX_VAL(CP(D2D_MCAD25), ? ? ? (IEN ?| PTD | EN ?| M0)) /*d2d_mcad25*/\
+ MUX_VAL(CP(D2D_MCAD26), ? ? ? (IEN ?| PTD | EN ?| M0)) /*d2d_mcad26*/\
+ MUX_VAL(CP(D2D_MCAD27), ? ? ? (IEN ?| PTD | EN ?| M0)) /*d2d_mcad27*/\
+ MUX_VAL(CP(D2D_MCAD28), ? ? ? (IEN ?| PTD | EN ?| M0)) /*d2d_mcad28*/\
+ MUX_VAL(CP(D2D_MCAD29), ? ? ? (IEN ?| PTD | EN ?| M0)) /*d2d_mcad29*/\
+ MUX_VAL(CP(D2D_MCAD30), ? ? ? (IEN ?| PTD | EN ?| M0)) /*d2d_mcad30*/\
+ MUX_VAL(CP(D2D_MCAD31), ? ? ? (IEN ?| PTD | EN ?| M0)) /*d2d_mcad31*/\
+ MUX_VAL(CP(D2D_MCAD32), ? ? ? (IEN ?| PTD | EN ?| M0)) /*d2d_mcad32*/\
+ MUX_VAL(CP(D2D_MCAD33), ? ? ? (IEN ?| PTD | EN ?| M0)) /*d2d_mcad33*/\
+ MUX_VAL(CP(D2D_MCAD34), ? ? ? (IEN ?| PTD | EN ?| M0)) /*d2d_mcad34*/\
+ MUX_VAL(CP(D2D_MCAD35), ? ? ? (IEN ?| PTD | EN ?| M0)) /*d2d_mcad35*/\
+ MUX_VAL(CP(D2D_MCAD36), ? ? ? (IEN ?| PTD | EN ?| M0)) /*d2d_mcad36*/\
+ MUX_VAL(CP(D2D_CLK26MI), ? ? ?(IEN ?| PTD | DIS | M0)) /*d2d_clk26mi*/\
+ MUX_VAL(CP(D2D_NRESPWRON), ? ?(IEN ?| PTD | EN ?| M0)) /*d2d_nrespwron*/\
+ MUX_VAL(CP(D2D_NRESWARM), ? ? (IEN ?| PTU | EN ?| M0)) /*d2d_nreswarm */\
+ MUX_VAL(CP(D2D_ARM9NIRQ), ? ? (IEN ?| PTD | DIS | M0)) /*d2d_arm9nirq */\
+ MUX_VAL(CP(D2D_UMA2P6FIQ), ? ?(IEN ?| PTD | DIS | M0)) /*d2d_uma2p6fiq*/\
+ MUX_VAL(CP(D2D_SPINT), ? ? ? ? ? ? ? ?(IEN ?| PTD | EN ?| M0)) /*d2d_spint*/\
+ MUX_VAL(CP(D2D_FRINT), ? ? ? ? ? ? ? ?(IEN ?| PTD | EN ?| M0)) /*d2d_frint*/\
+ MUX_VAL(CP(D2D_DMAREQ0), ? ? ?(IEN ?| PTD | DIS | M0)) /*d2d_dmareq0*/\
+ MUX_VAL(CP(D2D_DMAREQ1), ? ? ?(IEN ?| PTD | DIS | M0)) /*d2d_dmareq1*/\
+ MUX_VAL(CP(D2D_DMAREQ2), ? ? ?(IEN ?| PTD | DIS | M0)) /*d2d_dmareq2*/\
+ MUX_VAL(CP(D2D_DMAREQ3), ? ? ?(IEN ?| PTD | DIS | M0)) /*d2d_dmareq3*/\
+ MUX_VAL(CP(D2D_N3GTRST), ? ? ?(IEN ?| PTD | DIS | M0)) /*d2d_n3gtrst*/\
+ MUX_VAL(CP(D2D_N3GTDI), ? ? ? (IEN ?| PTD | DIS | M0)) /*d2d_n3gtdi*/\
+ MUX_VAL(CP(D2D_N3GTDO), ? ? ? (IEN ?| PTD | DIS | M0)) /*d2d_n3gtdo*/\
+ MUX_VAL(CP(D2D_N3GTMS), ? ? ? (IEN ?| PTD | DIS | M0)) /*d2d_n3gtms*/\
+ MUX_VAL(CP(D2D_N3GTCK), ? ? ? (IEN ?| PTD | DIS | M0)) /*d2d_n3gtck*/\
+ MUX_VAL(CP(D2D_N3GRTCK), ? ? ?(IEN ?| PTD | DIS | M0)) /*d2d_n3grtck*/\
+ MUX_VAL(CP(D2D_MSTDBY), ? ? ? (IEN ?| PTU | EN ?| M0)) /*d2d_mstdby*/\
+ MUX_VAL(CP(D2D_SWAKEUP), ? ? ?(IEN ?| PTD | EN ?| M0)) /*d2d_swakeup*/\

board/omap3/kboc/kboc.h line 380

Quoted 10 lines
board/omap3/kboc/kboc.h new file +10 -0
+ MUX_VAL(CP(D2D_IDLEREQ), ? ? ?(IEN ?| PTD | DIS | M0)) /*d2d_idlereq*/\
+ MUX_VAL(CP(D2D_IDLEACK), ? ? ?(IEN ?| PTU | EN ?| M0)) /*d2d_idleack*/\
+ MUX_VAL(CP(D2D_MWRITE), ? ? ? (IEN ?| PTD | DIS | M0)) /*d2d_mwrite*/\
+ MUX_VAL(CP(D2D_SWRITE), ? ? ? (IEN ?| PTD | DIS | M0)) /*d2d_swrite*/\
+ MUX_VAL(CP(D2D_MREAD), ? ? ? ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*d2d_mread*/\
+ MUX_VAL(CP(D2D_SREAD), ? ? ? ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*d2d_sread*/\
+ MUX_VAL(CP(D2D_MBUSFLAG), ? ? (IEN ?| PTD | DIS | M0)) /*d2d_mbusflag*/\
+ MUX_VAL(CP(D2D_SBUSFLAG), ? ? (IEN ?| PTD | DIS | M0)) /*d2d_sbusflag*/\
+ MUX_VAL(CP(SDRC_CKE0), ? ? ? ? ? ? ? ?(IDIS | PTU | EN ?| M0)) /*sdrc_cke0*/\
+ MUX_VAL(CP(SDRC_CKE1), ? ? ? ? ? ? ? ?(IDIS | PTU | EN ?| M0)) /*sdrc_cke1*/

one more reason why the mux needs a big change in mux handling :( I think we will end up with 1/2 a dozen crazy and code repetition for each board... Arrggghhh...

Quoted 334 lines
board/omap3/kboc/kboc.h new file +2 -0
+
+#endif
include/configs/omap3_kboc.h new file +317 -1
new file mode 100644
index 0000000..8a59612
@@ -0,0 +1,317 @@
+/*
+ * (C) Copyright 2009
+ * KwikByte <www.kwikbyte.com>
+ *
+ * Author :
+ * ?Christian Owens <[email protected]>
+ *
+ * Configuration settings for the KwikByte OMAP3530 KBOC Module.
+ *
+ * Derived from the following:
+ *
+ * (C) Copyright 2006-2008
+ * Texas Instruments.
+ * Richard Woodruff <[email protected]>
+ * Syed Mohammed Khasim <[email protected]>
+ *
+ * Configuration settings for the TI OMAP3530 Beagle board.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. ? ? ? ? See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+#include <asm/sizes.h>
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_ARMCORTEXA8 ? ? 1 ? ? ? /* This is an ARM V7 CPU core */
+#define CONFIG_OMAP ? ? ? ? ? ? ? ? ? ?1 ? ? ? /* in a TI OMAP core */
+#define CONFIG_OMAP34XX ? ? ? ? ? ? ? ?1 ? ? ? /* which is a 34XX */
+#define CONFIG_OMAP3430 ? ? ? ? ? ? ? ?1 ? ? ? /* which is in a 3430 */
+#define CONFIG_OMAP3_KBOC ? ? ?1 ? ? ? /* working with KBOC */
+
+#include <asm/arch/cpu.h> ? ? ? ? ? ? ?/* get chip and board defs */
+#include <asm/arch/omap3.h>
+
+/*
+ * Display CPU and Board information
+ */
+#define CONFIG_DISPLAY_CPUINFO ? ? ? ? 1
+#define CONFIG_DISPLAY_BOARDINFO ? ? ? 1
+
+/* Clock Defines */
+#define V_OSCK ? ? ? ? ? ? ? ? 26000000 ? ? ? ?/* Clock output from T2 */
+#define V_SCLK ? ? ? ? ? ? ? ? (V_OSCK >> 1)
+
+#undef CONFIG_USE_IRQ ? ? ? ? ? ? ? ? ? ? ? ? ?/* no support for IRQs */
+#define CONFIG_MISC_INIT_R
+
+#define CONFIG_CMDLINE_TAG ? ? ? ? ? ? 1 ? ? ? /* enable passing of ATAGs */
+#define CONFIG_SETUP_MEMORY_TAGS ? ? ? 1
+#define CONFIG_INITRD_TAG ? ? ? ? ? ? ?1
+#define CONFIG_REVISION_TAG ? ? ? ? ? ?1
+
+/*
+ * Size of malloc() pool
+ */
+#define CONFIG_ENV_SIZE ? ? ? ? ? ? ? ? ? ? ? ?SZ_128K /* Total Size Environment */
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? /* Sector */
+#define CONFIG_SYS_MALLOC_LEN ? ? ? ? ?(CONFIG_ENV_SIZE + SZ_128K)
+#define CONFIG_SYS_GBL_DATA_SIZE ? ? ? 128 ? ? /* bytes reserved for */
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? /* initial data */
+
+/*
+ * Hardware drivers
+ */
+
+/*
+ * NS16550 Configuration
+ */
+#define V_NS16550_CLK ? ? ? ? ? ? ? ? ?48000000 ? ? ? ?/* 48MHz (APLL96/2) */
+
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE ? ?(-4)
+#define CONFIG_SYS_NS16550_CLK ? ? ? ? V_NS16550_CLK
+
+/*
+ * select serial console configuration
+ */
+#define CONFIG_CONS_INDEX ? ? ? ? ? ? ?3
+#define CONFIG_SYS_NS16550_COM3 ? ? ? ? ? ? ? ?OMAP34XX_UART3
+#define CONFIG_SERIAL3 ? ? ? ? ? ? ? ? 3 ? ? ? /* UART3 on KBOC Rev 0.90 */
+
+/* allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+#define CONFIG_BAUDRATE ? ? ? ? ? ? ? ? ? ? ? ?115200
+#define CONFIG_SYS_BAUDRATE_TABLE ? ? ?{4800, 9600, 19200, 38400, 57600,\
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? 115200}
+#define CONFIG_MMC ? ? ? ? ? ? ? ? ? ? 1
+#define CONFIG_OMAP3_MMC ? ? ? ? ? ? ? 1
+#define CONFIG_DOS_PARTITION ? ? ? ? ? 1
+
+/* commands to include */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_EXT2 ? ? ? ? ? ? ? ?/* EXT2 Support ? ? ? ? ? ? ? ? */
+#define CONFIG_CMD_FAT ? ? ? ? /* FAT support ? ? ? ? ? ? ? ? ?*/
+#define CONFIG_CMD_JFFS2 ? ? ? /* JFFS2 Support ? ? ? ? ? ? ? ?*/
+#define CONFIG_CMD_MTDPARTS ? ?/* Enable MTD parts commands */
+#define CONFIG_MTD_DEVICE ? ? ?/* needed for mtdparts commands */
+#define MTDIDS_DEFAULT ? ? ? ? ? ? ? ? "nand0=nand"
+#define MTDPARTS_DEFAULT ? ? ? ? ? ? ? "mtdparts=nand:512k(x-loader),"\
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? "1920k(u-boot),128k(u-boot-env),"\
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? "4m(kernel),-(fs)"
+
+#define CONFIG_CMD_I2C ? ? ? ? /* I2C serial bus support ? ? ? */
+#define CONFIG_CMD_MMC ? ? ? ? /* MMC support ? ? ? ? ? ? ? ? ?*/
+#define CONFIG_CMD_NAND ? ? ? ? ? ? ? ?/* NAND support ? ? ? ? ? ? ? ? */
+
+#undef CONFIG_CMD_FLASH ? ? ? ? ? ? ? ?/* flinfo, erase, protect ? ? ? */
+#undef CONFIG_CMD_FPGA ? ? ? ? /* FPGA configuration Support ? */
+#undef CONFIG_CMD_IMI ? ? ? ? ?/* iminfo ? ? ? ? ? ? ? ? ? ? ? */
+#undef CONFIG_CMD_IMLS ? ? ? ? /* List all found images ? ? ? ?*/
+#undef CONFIG_CMD_NET ? ? ? ? ?/* bootp, tftpboot, rarpboot ? ?*/
+#undef CONFIG_CMD_NFS ? ? ? ? ?/* NFS support ? ? ? ? ? ? ? ? ?*/
+
+#define CONFIG_SYS_NO_FLASH
+#define CONFIG_SYS_I2C_SPEED ? ? ? ? ? 100000
+#define CONFIG_SYS_I2C_SLAVE ? ? ? ? ? 1
+#define CONFIG_SYS_I2C_BUS ? ? ? ? ? ? 0
+#define CONFIG_SYS_I2C_BUS_SELECT ? ? ?1
+#define CONFIG_DRIVER_OMAP34XX_I2C ? ? 1
+
+/*
+ * Board NAND Info.
+ */
+#define CONFIG_NAND_OMAP_GPMC
+#define CONFIG_SYS_NAND_ADDR ? ? ? ? ? NAND_BASE ? ? ? /* physical address */
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? /* to access nand */
+#define CONFIG_SYS_NAND_BASE ? ? ? ? ? NAND_BASE ? ? ? /* physical address */
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? /* to access nand at */
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? /* CS0 */
+#define GPMC_NAND_ECC_LP_x16_LAYOUT ? ?1
+
+#define CONFIG_SYS_MAX_NAND_DEVICE ? ? 1 ? ? ? ? ? ? ? /* Max number of NAND */
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? /* devices */
+
+#define CONFIG_JFFS2_NAND
+/* nand device jffs2 lives on */
+#define CONFIG_JFFS2_DEV ? ? ? ? ? ? ? "nand0"
+/* start of jffs2 partition */
+#define CONFIG_JFFS2_PART_OFFSET ? ? ? 0x680000
+#define CONFIG_JFFS2_PART_SIZE ? ? ? ? 0xf980000 ? ? ? /* size of jffs2 */
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? /* partition */
+
+/* Environment information */
+#define CONFIG_BOOTDELAY ? ? ? ? ? ? ? 3
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ ? ? ? "loadaddr=0x82000000\0" \
+ ? ? ? "console=ttyS2,115200n8\0" \
+ ? ? ? "videomode=1024x768 at 60,vxres=1024,vyres=768\0" \
+ ? ? ? "videospec=omapfb:vram:2M,vram:4M\0" \
+ ? ? ? "mmcargs=setenv bootargs console=${console} " \
+ ? ? ? ? ? ? ? "video=${videospec},mode:${videomode} " \
+ ? ? ? ? ? ? ? "root=/dev/mmcblk0p2 rw " \
+ ? ? ? ? ? ? ? "rootfstype=ext3 rootwait " \
+ ? ? ? ? ? ? ? "${optargs}\0" \
+ ? ? ? "nandargs=setenv bootargs console=${console} " \
+ ? ? ? ? ? ? ? "video=${videospec},mode:${videomode} " \
+ ? ? ? ? ? ? ? "root=/dev/mtdblock4 rw " \
+ ? ? ? ? ? ? ? "rootfstype=jffs2 " \
+ ? ? ? ? ? ? ? "${optargs}\0" \
+ ? ? ? "loadbootscript=fatload mmc 0 ${loadaddr} boot.scr\0" \
+ ? ? ? "bootscript=echo Running bootscript from mmc ...; " \
+ ? ? ? ? ? ? ? "source ${loadaddr}\0" \
+ ? ? ? "loaduimage=fatload mmc 0 ${loadaddr} uImage\0" \
+ ? ? ? "mmcboot=echo Booting from mmc ...; " \
+ ? ? ? ? ? ? ? "run mmcargs; " \
+ ? ? ? ? ? ? ? "bootm ${loadaddr}\0" \
+ ? ? ? "nandboot=echo Booting from nand ...; " \
+ ? ? ? ? ? ? ? "run nandargs; " \
+ ? ? ? ? ? ? ? "nand read ${loadaddr} 280000 400000; " \
+ ? ? ? ? ? ? ? "bootm ${loadaddr}\0" \
+
+#define CONFIG_BOOTCOMMAND \
+ ? ? ? "if mmc init; then " \
+ ? ? ? ? ? ? ? "if run loadbootscript; then " \
+ ? ? ? ? ? ? ? ? ? ? ? "run bootscript; " \
+ ? ? ? ? ? ? ? "else " \
+ ? ? ? ? ? ? ? ? ? ? ? "if run loaduimage; then " \
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? "run mmcboot; " \
+ ? ? ? ? ? ? ? ? ? ? ? "else run nandboot; " \
+ ? ? ? ? ? ? ? ? ? ? ? "fi; " \
+ ? ? ? ? ? ? ? "fi; " \
+ ? ? ? "else run nandboot; fi"
+
+#define CONFIG_AUTO_COMPLETE ? ? ? ? ? 1
+/*
+ * Miscellaneous configurable options
+ */
+#define V_PROMPT ? ? ? ? ? ? ? ? ? ? ? "OMAP3_KBOC # "
+
+#define CONFIG_SYS_LONGHELP ? ? ? ? ? ?/* undef to save memory */
+#define CONFIG_SYS_HUSH_PARSER ? ? ? ? /* use "hush" command parser */
+#define CONFIG_SYS_PROMPT_HUSH_PS2 ? ? "> "
+#define CONFIG_SYS_PROMPT ? ? ? ? ? ? ?V_PROMPT
+#define CONFIG_SYS_CBSIZE ? ? ? ? ? ? ?256 ? ? /* Console I/O Buffer Size */
+/* Print Buffer Size */
+#define CONFIG_SYS_PBSIZE ? ? ? ? ? ? ?(CONFIG_SYS_CBSIZE + \
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_MAXARGS ? ? ? ? ? ? 16 ? ? ?/* max number of command args */
+/* Boot Argument Buffer Size */
+#define CONFIG_SYS_BARGSIZE ? ? ? ? ? ?(CONFIG_SYS_CBSIZE)
+
+#define CONFIG_SYS_MEMTEST_START ? ? ? (OMAP34XX_SDRC_CS0) ? ? /* memtest */
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? /* works on */
+#define CONFIG_SYS_MEMTEST_END ? ? ? ? (OMAP34XX_SDRC_CS0 + \
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? 0x01F00000) /* 31MB */
+
+#define CONFIG_SYS_LOAD_ADDR ? ? ? ? ? (OMAP34XX_SDRC_CS0) ? ? /* default */
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? /* load address */
+
+/*
+ * OMAP3 has 12 GP timers, they can be driven by the system clock
+ * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK).
+ * This rate is divided by a local divisor.
+ */
+#define CONFIG_SYS_TIMERBASE ? ? ? ? ? (OMAP34XX_GPT2)
+#define CONFIG_SYS_PTV ? ? ? ? ? ? ? ? 2 ? ? ? /* Divisor: 2^(PTV+1) => 8 */
+#define CONFIG_SYS_HZ ? ? ? ? ? ? ? ? ?1000
+
+/*-----------------------------------------------------------------------
+ * Stack sizes
+ *
+ * The stack sizes are set up in start.S using the settings below
+ */
+#define CONFIG_STACKSIZE ? ? ? SZ_128K /* regular stack */
+#ifdef CONFIG_USE_IRQ
+#define CONFIG_STACKSIZE_IRQ ? SZ_4K ? /* IRQ stack */
+#define CONFIG_STACKSIZE_FIQ ? SZ_4K ? /* FIQ stack */
+#endif
+
+/*-----------------------------------------------------------------------
+ * Physical Memory Map
+ */
+#define CONFIG_NR_DRAM_BANKS ? 2 ? ? ? /* CS1 may or may not be populated */
+#define PHYS_SDRAM_1 ? ? ? ? ? OMAP34XX_SDRC_CS0
+#define PHYS_SDRAM_1_SIZE ? ? ?SZ_32M ?/* at least 32 meg */
+#define PHYS_SDRAM_2 ? ? ? ? ? OMAP34XX_SDRC_CS1
+
+/* SDRAM Bank Allocation method */
+#define SDRC_R_B_C ? ? ? ? ? ? 1
+
+/*-----------------------------------------------------------------------
+ * FLASH and environment organization
+ */
+
+/* **** PISMO SUPPORT *** */
+
+/* Configure the PISMO */
+#define PISMO1_NAND_SIZE ? ? ? ? ? ? ? GPMC_SIZE_128M
+#define PISMO1_ONEN_SIZE ? ? ? ? ? ? ? GPMC_SIZE_128M
+
+#define CONFIG_SYS_MAX_FLASH_SECT ? ? ?520 ? ? /* max number of sectors on */
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? /* one chip */
+#define CONFIG_SYS_MAX_FLASH_BANKS ? ? 2 ? ? ? /* max number of flash banks */
+#define CONFIG_SYS_MONITOR_LEN ? ? ? ? SZ_256K /* Reserve 2 sectors */
+
+#define CONFIG_SYS_FLASH_BASE ? ? ? ? ?boot_flash_base
+
+/* Monitor at start of flash */
+#define CONFIG_SYS_MONITOR_BASE ? ? ? ? ? ? ? ?CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_ONENAND_BASE ? ? ? ? ? ? ? ?ONENAND_MAP
+
+#define CONFIG_ENV_IS_IN_NAND ? ? ? ? ?1
+#define ONENAND_ENV_OFFSET ? ? ? ? ? ? 0x260000 /* environment starts here */
+#define SMNAND_ENV_OFFSET ? ? ? ? ? ? ?0x260000 /* environment starts here */
+
+#define CONFIG_SYS_ENV_SECT_SIZE ? ? ? boot_flash_sec
+#define CONFIG_ENV_OFFSET ? ? ? ? ? ? ?boot_flash_off
+#define CONFIG_ENV_ADDR ? ? ? ? ? ? ? ? ? ? ? ?SMNAND_ENV_OFFSET
+
+/*-----------------------------------------------------------------------
+ * CFI FLASH driver setup
+ */
+/* timeout values are in ticks */
+#define CONFIG_SYS_FLASH_ERASE_TOUT ? ?(100 * CONFIG_SYS_HZ)
+#define CONFIG_SYS_FLASH_WRITE_TOUT ? ?(100 * CONFIG_SYS_HZ)
+
+/* Flash banks JFFS2 should use */
+#define CONFIG_SYS_MAX_MTD_BANKS ? ? ? (CONFIG_SYS_MAX_FLASH_BANKS + \
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? CONFIG_SYS_MAX_NAND_DEVICE)
+#define CONFIG_SYS_JFFS2_MEM_NAND
+/* use flash_info[2] */
+#define CONFIG_SYS_JFFS2_FIRST_BANK ? ?CONFIG_SYS_MAX_FLASH_BANKS
+#define CONFIG_SYS_JFFS2_NUM_BANKS ? ? 1
+
+#ifndef __ASSEMBLY__
+extern gpmc_csx_t *nand_cs_base;
+extern gpmc_t *gpmc_cfg_base;
+extern unsigned int boot_flash_base;
+extern volatile unsigned int boot_flash_env_addr;
+extern unsigned int boot_flash_off;
+extern unsigned int boot_flash_sec;
+extern unsigned int boot_flash_type;
+#endif
+
+#endif /* __CONFIG_H */
--

1.5.4.3

_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot

#2 lore raw

PATCH 1/1 Add support for the KwikByte KBOC OMAP35xx board

Quoting Nishanth Menon <[email protected]>:

Quoted 4 lines · On Thu, Jul 9, 2009 at 6:03 PM, <[email protected]> wrote:
Quoted 1 line

Subject: [PATCH] Add support for the KwikByte KBOC OMAP35xx board

Do you have some link that you can point us to what is KwikByte KBOC board? give us some explanation..

The KBOC <www.kwikbyte.com/KBOC.html> is a system module intended to help users transition easily from from single boards to larger production volume. By design, the hardware is very much like the BeagleBoard which explains the code similarities.

Quoted 135 lines
Quoted 135 lines

---

?MAINTAINERS ? ? ? ? ? ? ? ? ?| ? ?4 +
?MAKEALL ? ? ? ? ? ? ? ? ? ? ?| ? ?1 +
?Makefile ? ? ? ? ? ? ? ? ? ? | ? ?3 +
?board/omap3/common/Makefile ?| ? ?1 +
?board/omap3/kboc/Makefile ? ?| ? 49 ++++++
?board/omap3/kboc/config.mk ? | ? 33 ++++
?board/omap3/kboc/kboc.c ? ? ?| ?106 ++++++++++++
?board/omap3/kboc/kboc.h ? ? ?| ?382

++++++++++++++++++++++++++++++++++++++++++
?include/configs/omap3_kboc.h | ?317 +++++++++++++++++++++++++++++++++++ ?9 files changed, 896 insertions(+), 0 deletions(-)
?create mode 100644 board/omap3/kboc/Makefile
?create mode 100644 board/omap3/kboc/config.mk
?create mode 100644 board/omap3/kboc/kboc.c
?create mode 100644 board/omap3/kboc/kboc.h
?create mode 100644 include/configs/omap3_kboc.h

MAINTAINERS +0 -0
index 0041112..cc55df9 100644
@@ -686,6 +686,10 @@ Alex Z

? ? ? ?lart ? ? ? ? ? ?SA1100
? ? ? ?dnp1110 ? ? ? ? SA1110

MAINTAINERS +4 -0
+Christian Owens <[email protected]>
+
+ ? ? ? omap3_kboc ? ? ?ARM CORTEX-A8 (OMAP35xx SoC)
+

?-------------------------------------------------------------------------

?Unknown / orphaned boards:

MAKEALL +1 -0
index 41f1445..ac0c5d9 100755
@@ -572,6 +572,7 @@ LIST_ARM_CORTEX_A8=" ? ? ? ? ? ? ? ?\
 ? ? ? ?omap3_pandora ? ? ? ? ? \
 ? ? ? ?omap3_zoom1 ? ? ? ? ? ? \
 ? ? ? ?omap3_zoom2 ? ? ? ? ? ? \
+ ? ? ? omap3_kboc ? ? ? ? ? ? ?\

?"

?#########################################################################

Makefile +0 -0
index 2a06440..b204917 100644
@@ -3040,6 +3040,9 @@ omap3_zoom1_config : ? ? ?unconfig

?omap3_zoom2_config : ?unconfig
? ? ? ?@$(MKCONFIG) $(@:_config=) arm arm_cortexa8 zoom2 omap3 omap3

Makefile +3 -0
+omap3_kboc_config : ? ?unconfig
+ ? ? ? @$(MKCONFIG) $(@:_config=) arm arm_cortexa8 kboc omap3 omap3
+

?######################################################################### ?## XScale Systems ?#########################################################################

board/omap3/common/Makefile +0 -0
index b8a0b14..4f7a20b 100644
@@ -34,6 +34,7 @@ COBJS-$(CONFIG_OMAP3_OVERO) += power.o

?COBJS-$(CONFIG_OMAP3_PANDORA) += power.o
?COBJS-$(CONFIG_OMAP3_ZOOM1) += power.o
?COBJS-$(CONFIG_OMAP3_ZOOM2) += power.o
+COBJS-$(CONFIG_OMAP3_KBOC) += power.o

?COBJS := $(COBJS-y)
?SRCS ?:= $(COBJS:.o=.c)

board/omap3/kboc/Makefile new file +49 -0
new file mode 100644
index 0000000..2c77444
@@ -0,0 +1,49 @@
+#
+# (C) Copyright 2000, 2001, 2002
+# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. ?See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB ? ?= $(obj)lib$(BOARD).a
+
+COBJS ?:= kboc.o
+
+SRCS ? := $(COBJS:.o=.c)
+OBJS ? := $(addprefix $(obj),$(COBJS))
+
+$(LIB): ? ? ? ?$(obj).depend $(OBJS)
+ ? ? ? $(AR) $(ARFLAGS) $@ $(OBJS)
+
+clean:
+ ? ? ? rm -f $(OBJS)
+
+distclean: ? ? clean
+ ? ? ? rm -f $(LIB) core *.bak $(obj).depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
board/omap3/kboc/config.mk new file +0 -0
new file mode 100644
index 0000000..879b2e2
@@ -0,0 +1,33 @@
Quoted 8 lines

board/omap3/kboc/config.mk line 6

Quoted 6 lines
board/omap3/kboc/config.mk new file +6 -0
+#
+# (C) Copyright 2006
+# Texas Instruments, <www.ti.com>
+#
+# Beagle Board uses OMAP3 (ARM-CortexA8) cpu
+# see http://www.ti.com/ for more information on Texas Instruments

is this board beagleboard? should this be here? mebbe you could take state copyrights right?

We use the same (copy of) file in the new directory. Without any changes, I assume the original copyrights should remain?

Quoted 32 lines
Quoted 32 lines
board/omap3/kboc/config.mk new file +27 -0
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. ?See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+# Physical Address:
+# 8000'0000 (bank0)
+# A000/0000 (bank1)
+# Linux-Kernel is expected to be at 8000'8000, entry 8000'8000
+# (mem base + reserved)
+
+# For use with external or internal boots.
+TEXT_BASE = 0x80e80000
board/omap3/kboc/kboc.c new file +0 -0
new file mode 100644
index 0000000..5fc9b96
Quoted 8 lines

board/omap3/kboc/kboc.c line 4

Quoted 5 lines
board/omap3/kboc/kboc.c new file +4 -0
@@ -0,0 +1,106 @@
+/*
+ * (C) Copyright 2009
+ * KwikByte <www.kwikbyte.com>
+ *

bit more info on the board is so useful for someone to read - remember you would be selling your board this way too.. give us more info and we can hopefully help..

Thanks. I can add more description.

Quoted 90 lines
Quoted 78 lines
board/omap3/kboc/kboc.c new file +76 -0
+ * Author :
+ * ?Christian Owens <[email protected]>
+ *
+ * Derived from the following:
+ *
+ * (C) Copyright 2004-2008
+ * Texas Instruments, <www.ti.com>
+ *
+ * Author :
+ * ? ? Sunil Kumar <[email protected]>
+ * ? ? Shashi Ranjan <[email protected]>
+ *
+ * Derived from Beagle Board and 3430 SDP code by
+ * ? ? Richard Woodruff <[email protected]>
+ * ? ? Syed Mohammed Khasim <[email protected]>
+ *
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. ?See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/mux.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/gpio.h>
+#include <asm/mach-types.h>
+#include "kboc.h"
+
+/*
+ * Routine: board_init
+ * Description: Early hardware init.
+ */
+int board_init(void)
+{
+ ? ? ? DECLARE_GLOBAL_DATA_PTR;
+
+ ? ? ? gpmc_init(); /* in SRAM or SDRAM, finish GPMC */
+ ? ? ? /* board id for Linux */
+ ? ? ? gd->bd->bi_arch_number = MACH_TYPE_OMAP3_KBOC;
+ ? ? ? /* boot param addr */
+ ? ? ? gd->bd->bi_boot_params = (OMAP34XX_SDRC_CS0 + 0x100);
+
+ ? ? ? return 0;
+}
+
+/*
+ * Routine: misc_init_r
+ * Description: Configure board specific parts
+ */
+int misc_init_r(void)
+{
+ ? ? ? gpio_t *gpio1_base = (gpio_t *)OMAP34XX_GPIO1_BASE;
+ ? ? ? gpio_t *gpio5_base = (gpio_t *)OMAP34XX_GPIO5_BASE;
+ ? ? ? gpio_t *gpio6_base = (gpio_t *)OMAP34XX_GPIO6_BASE;
+
+ ? ? ? power_init_r();
+
+ ? ? ? /* Configure GPIOs to output */
+ ? ? ? writel(~(GPIO23 | GPIO17 | GPIO12 | GPIO11 | GPIO10 | GPIO8  
 | GPIO2),
+ ? ? ? ? ? ? ? &gpio6_base->oe);
+ ? ? ? writel(~(GPIO31 | GPIO30 | GPIO29 | GPIO28 | GPIO22 | GPIO21 |

board/omap3/kboc/kboc.c

Quoted 10 lines
board/omap3/kboc/kboc.c new file +10 -0
+ ? ? ? ? ? ? ? GPIO13 | GPIO12), &gpio5_base->oe);
+ ? ? ? writel(~(GPIO22 | GPIO13), &gpio1_base->oe);
+
+ ? ? ? /* Set GPIOs */
+ ? ? ? writel(GPIO23 | GPIO17 | GPIO10 | GPIO8 | GPIO2,
+ ? ? ? ? ? ? ? &gpio6_base->setdataout);
+ ? ? ? writel(GPIO31 | GPIO29 | GPIO28 | GPIO22 | GPIO21 | GPIO13 | GPIO12,
+ ? ? ? ? ? ? ? &gpio5_base->setdataout);
+ ? ? ? writel(GPIO22 | GPIO13,
+ ? ? ? ? ? ? ? &gpio1_base->setdataout);

Aieeeee....... what are these gpios and why do they need to be set high?

Quoted 1 line

normally you might want to do setdataout followed by oe?

This format is taken directly from the existing code for BeagleBoard. The pins are a little different and I can add some comments.

Quoted 58 lines
Quoted 58 lines
board/omap3/kboc/kboc.c new file +16 -0
+
+ ? ? ? dieid_num_r();
+
+ ? ? ? return 0;
+}
+
+/*
+ * Routine: set_muxconf_regs
+ * Description: Setting up the configuration Mux registers specific to the
+ * ? ? ? ? ? ? hardware. Many pins need to be moved from protect to primary
+ * ? ? ? ? ? ? mode.
+ */
+void set_muxconf_regs(void)
+{
+ ? ? ? MUX_KBOC();
+}
board/omap3/kboc/kboc.h new file +36 -0
new file mode 100644
index 0000000..41c3b9e
@@ -0,0 +1,382 @@
+/*
+ * (C) Copyright 2009
+ * KwikByte <www.kwikbyte.com>
+ *
+ * Author :
+ * ?Christian Owens <[email protected]>
+ *
+ * Derived from the following:
+ *
+ * (C) Copyright 2008
+ * Dirk Behme <[email protected]>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. ?See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+#ifndef _KBOC_H_
+#define _KBOC_H_
+
+const omap3_sysinfo sysinfo = {
+ ? ? ? DDR_STACKED,
+ ? ? ? "OMAP3 KBOC board",
Quoted 8 lines

board/omap3/kboc/kboc.h line 41

Quoted 5 lines
board/omap3/kboc/kboc.h new file +5 -0
+#if defined(CONFIG_ENV_IS_IN_ONENAND)
+ ? ? ? "OneNAND",
+#else
+ ? ? ? "NAND",
+#endif

err... CONFIG_ENV_IS_IN_NAND is defined as 1 in config header.. means never support onenand?

This is also taken from existing BeagleBoard code. I can remove the conditional.

Quoted 407 lines
Quoted 407 lines
board/omap3/kboc/kboc.h new file +48 -0
+};
+
+/*
+ * IEN ?- Input Enable
+ * IDIS - Input Disable
+ * PTD ?- Pull type Down
+ * PTU ?- Pull type Up
+ * DIS ?- Pull type selection is inactive
+ * EN ? - Pull type selection is active
+ * M0 ? - Mode 0
+ * The commented string gives the final mux configuration for that pin
+ */
+#define MUX_KBOC() \
+ /*SDRC*/\
+ MUX_VAL(CP(SDRC_D0), ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*SDRC_D0*/\
+ MUX_VAL(CP(SDRC_D1), ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*SDRC_D1*/\
+ MUX_VAL(CP(SDRC_D2), ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*SDRC_D2*/\
+ MUX_VAL(CP(SDRC_D3), ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*SDRC_D3*/\
+ MUX_VAL(CP(SDRC_D4), ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*SDRC_D4*/\
+ MUX_VAL(CP(SDRC_D5), ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*SDRC_D5*/\
+ MUX_VAL(CP(SDRC_D6), ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*SDRC_D6*/\
+ MUX_VAL(CP(SDRC_D7), ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*SDRC_D7*/\
+ MUX_VAL(CP(SDRC_D8), ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*SDRC_D8*/\
+ MUX_VAL(CP(SDRC_D9), ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*SDRC_D9*/\
+ MUX_VAL(CP(SDRC_D10), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*SDRC_D10*/\
+ MUX_VAL(CP(SDRC_D11), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*SDRC_D11*/\
+ MUX_VAL(CP(SDRC_D12), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*SDRC_D12*/\
+ MUX_VAL(CP(SDRC_D13), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*SDRC_D13*/\
+ MUX_VAL(CP(SDRC_D14), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*SDRC_D14*/\
+ MUX_VAL(CP(SDRC_D15), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*SDRC_D15*/\
+ MUX_VAL(CP(SDRC_D16), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*SDRC_D16*/\
+ MUX_VAL(CP(SDRC_D17), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*SDRC_D17*/\
+ MUX_VAL(CP(SDRC_D18), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*SDRC_D18*/\
+ MUX_VAL(CP(SDRC_D19), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*SDRC_D19*/\
+ MUX_VAL(CP(SDRC_D20), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*SDRC_D20*/\
+ MUX_VAL(CP(SDRC_D21), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*SDRC_D21*/\
+ MUX_VAL(CP(SDRC_D22), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*SDRC_D22*/\
+ MUX_VAL(CP(SDRC_D23), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*SDRC_D23*/\
+ MUX_VAL(CP(SDRC_D24), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*SDRC_D24*/\
+ MUX_VAL(CP(SDRC_D25), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*SDRC_D25*/\
+ MUX_VAL(CP(SDRC_D26), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*SDRC_D26*/\
+ MUX_VAL(CP(SDRC_D27), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*SDRC_D27*/\
+ MUX_VAL(CP(SDRC_D28), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*SDRC_D28*/\
+ MUX_VAL(CP(SDRC_D29), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*SDRC_D29*/\
+ MUX_VAL(CP(SDRC_D30), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*SDRC_D30*/\
+ MUX_VAL(CP(SDRC_D31), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*SDRC_D31*/\
+ MUX_VAL(CP(SDRC_CLK), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*SDRC_CLK*/\
+ MUX_VAL(CP(SDRC_DQS0), ? ? ? ? ? ? ? ?(IEN ?| PTD | DIS | M0))   

/*SDRC_DQS0*/\
+ MUX_VAL(CP(SDRC_DQS1), ? ? ? ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*SDRC_DQS1*/\
+ MUX_VAL(CP(SDRC_DQS2), ? ? ? ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*SDRC_DQS2*/\
+ MUX_VAL(CP(SDRC_DQS3), ? ? ? ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*SDRC_DQS3*/\
+ /*GPMC*/\

+ MUX_VAL(CP(GPMC_A1), ? ? ? ? ?(IDIS | PTD | DIS | M0)) /*GPMC_A1*/\
+ MUX_VAL(CP(GPMC_A2), ? ? ? ? ?(IDIS | PTD | DIS | M0)) /*GPMC_A2*/\
+ MUX_VAL(CP(GPMC_A3), ? ? ? ? ?(IDIS | PTD | DIS | M0)) /*GPMC_A3*/\
+ MUX_VAL(CP(GPMC_A4), ? ? ? ? ?(IDIS | PTD | DIS | M0)) /*GPMC_A4*/\
+ MUX_VAL(CP(GPMC_A5), ? ? ? ? ?(IDIS | PTD | DIS | M0)) /*GPMC_A5*/\
+ MUX_VAL(CP(GPMC_A6), ? ? ? ? ?(IDIS | PTD | DIS | M0)) /*GPMC_A6*/\
+ MUX_VAL(CP(GPMC_A7), ? ? ? ? ?(IDIS | PTD | DIS | M0)) /*GPMC_A7*/\
+ MUX_VAL(CP(GPMC_A8), ? ? ? ? ?(IDIS | PTD | DIS | M0)) /*GPMC_A8*/\
+ MUX_VAL(CP(GPMC_A9), ? ? ? ? ?(IDIS | PTD | DIS | M0)) /*GPMC_A9*/\
+ MUX_VAL(CP(GPMC_A10), ? ? ? ? (IDIS | PTD | DIS | M0)) /*GPMC_A10*/\
+ MUX_VAL(CP(GPMC_D0), ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*GPMC_D0*/\
+ MUX_VAL(CP(GPMC_D1), ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*GPMC_D1*/\
+ MUX_VAL(CP(GPMC_D2), ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*GPMC_D2*/\
+ MUX_VAL(CP(GPMC_D3), ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*GPMC_D3*/\
+ MUX_VAL(CP(GPMC_D4), ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*GPMC_D4*/\
+ MUX_VAL(CP(GPMC_D5), ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*GPMC_D5*/\
+ MUX_VAL(CP(GPMC_D6), ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*GPMC_D6*/\
+ MUX_VAL(CP(GPMC_D7), ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*GPMC_D7*/\
+ MUX_VAL(CP(GPMC_D8), ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*GPMC_D8*/\
+ MUX_VAL(CP(GPMC_D9), ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*GPMC_D9*/\
+ MUX_VAL(CP(GPMC_D10), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*GPMC_D10*/\
+ MUX_VAL(CP(GPMC_D11), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*GPMC_D11*/\
+ MUX_VAL(CP(GPMC_D12), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*GPMC_D12*/\
+ MUX_VAL(CP(GPMC_D13), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*GPMC_D13*/\
+ MUX_VAL(CP(GPMC_D14), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*GPMC_D14*/\
+ MUX_VAL(CP(GPMC_D15), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*GPMC_D15*/\

+ MUX_VAL(CP(GPMC_NCS0), ? ? ? ? ? ? ? ?(IDIS | PTU | EN ?| M0)) /*GPMC_nCS0*/\
+ MUX_VAL(CP(GPMC_NCS1), ? ? ? ? ? ? ? ?(IDIS | PTU | EN ?| M0)) /*GPMC_nCS1*/\
+ MUX_VAL(CP(GPMC_NCS2), ? ? ? ? ? ? ? ?(IDIS | PTU | EN ?| M0)) /*GPMC_nCS2*/\
+ MUX_VAL(CP(GPMC_NCS3), ? ? ? ? ? ? ? ?(IDIS | PTU | EN ?| M0)) /*GPMC_nCS3*/\
+ MUX_VAL(CP(GPMC_NCS4), ? ? ? ? ? ? ? ?(IDIS | PTU | EN ?| M0)) /*GPMC_nCS4*/\
+ MUX_VAL(CP(GPMC_NCS5), ? ? ? ? ? ? ? ?(IDIS | PTD | DIS | M0)) /*GPMC_nCS5*/\
+ MUX_VAL(CP(GPMC_NCS6), ? ? ? ? ? ? ? ?(IEN ?| PTD | DIS | M1)) /*SYS_nDMA_REQ2*/\
+ MUX_VAL(CP(GPMC_NCS7), ? ? ? ? ? ? ? ?(IEN ?| PTU | EN ?| M1)) /*SYS_nDMA_REQ3*/\
+ MUX_VAL(CP(GPMC_NBE1), ? ? ? ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*GPMC_nBE1*/\

+ MUX_VAL(CP(GPMC_WAIT2), ? ? ? (IEN ?| PTU | EN ?| M0)) /*GPMC_WAIT2*/\
+ MUX_VAL(CP(GPMC_WAIT3), ? ? ? (IEN ?| PTU | EN ?| M0)) /*GPMC_WAIT3*/\
+ MUX_VAL(CP(GPMC_CLK), ? ? ? ? (IDIS | PTD | DIS | M0)) /*GPMC_CLK*/\
+ MUX_VAL(CP(GPMC_NADV_ALE), ? ?(IDIS | PTD | DIS | M0)) /*GPMC_nADV_ALE*/\
+ MUX_VAL(CP(GPMC_NOE), ? ? ? ? (IDIS | PTD | DIS | M0)) /*GPMC_nOE*/\
+ MUX_VAL(CP(GPMC_NWE), ? ? ? ? (IDIS | PTD | DIS | M0)) /*GPMC_nWE*/\
+ MUX_VAL(CP(GPMC_NBE0_CLE), ? ?(IDIS | PTD | DIS | M0)) /*GPMC_nBE0_CLE*/\
+ MUX_VAL(CP(GPMC_NWP), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*GPMC_nWP*/\
+ MUX_VAL(CP(GPMC_WAIT0), ? ? ? (IEN ?| PTU | EN ?| M0)) /*GPMC_WAIT0*/\
+ MUX_VAL(CP(GPMC_WAIT1), ? ? ? (IEN ?| PTU | EN ?| M0)) /*GPMC_WAIT1*/\

+ /*DSS*/\
+ MUX_VAL(CP(DSS_PCLK), ? ? ? ? (IDIS | PTD | DIS | M0)) /*DSS_PCLK*/\
+ MUX_VAL(CP(DSS_HSYNC), ? ? ? ? ? ? ? ?(IDIS | PTD | DIS | M0)) /*DSS_HSYNC*/\
+ MUX_VAL(CP(DSS_VSYNC), ? ? ? ? ? ? ? ?(IDIS | PTD | DIS | M0)) /*DSS_VSYNC*/\
+ MUX_VAL(CP(DSS_ACBIAS), ? ? ? (IDIS | PTD | DIS | M0)) /*DSS_ACBIAS*/\
+ MUX_VAL(CP(DSS_DATA0), ? ? ? ? ? ? ? ?(IDIS | PTD | DIS | M0)) /*DSS_DATA0*/\
+ MUX_VAL(CP(DSS_DATA1), ? ? ? ? ? ? ? ?(IDIS | PTD | DIS | M0)) /*DSS_DATA1*/\
+ MUX_VAL(CP(DSS_DATA2), ? ? ? ? ? ? ? ?(IDIS | PTD | DIS | M0)) /*DSS_DATA2*/\
+ MUX_VAL(CP(DSS_DATA3), ? ? ? ? ? ? ? ?(IDIS | PTD | DIS | M0)) /*DSS_DATA3*/\
+ MUX_VAL(CP(DSS_DATA4), ? ? ? ? ? ? ? ?(IDIS | PTD | DIS | M0)) /*DSS_DATA4*/\
+ MUX_VAL(CP(DSS_DATA5), ? ? ? ? ? ? ? ?(IDIS | PTD | DIS | M0)) /*DSS_DATA5*/\
+ MUX_VAL(CP(DSS_DATA6), ? ? ? ? ? ? ? ?(IDIS | PTD | DIS | M0)) /*DSS_DATA6*/\
+ MUX_VAL(CP(DSS_DATA7), ? ? ? ? ? ? ? ?(IDIS | PTD | DIS | M0)) /*DSS_DATA7*/\
+ MUX_VAL(CP(DSS_DATA8), ? ? ? ? ? ? ? ?(IDIS | PTD | DIS | M0)) /*DSS_DATA8*/\
+ MUX_VAL(CP(DSS_DATA9), ? ? ? ? ? ? ? ?(IDIS | PTD | DIS | M0)) /*DSS_DATA9*/\

+ MUX_VAL(CP(DSS_DATA10), ? ? ? (IDIS | PTD | DIS | M0)) /*DSS_DATA10*/\
+ MUX_VAL(CP(DSS_DATA11), ? ? ? (IDIS | PTD | DIS | M0)) /*DSS_DATA11*/\
+ MUX_VAL(CP(DSS_DATA12), ? ? ? (IDIS | PTD | DIS | M0)) /*DSS_DATA12*/\
+ MUX_VAL(CP(DSS_DATA13), ? ? ? (IDIS | PTD | DIS | M0)) /*DSS_DATA13*/\
+ MUX_VAL(CP(DSS_DATA14), ? ? ? (IDIS | PTD | DIS | M0)) /*DSS_DATA14*/\
+ MUX_VAL(CP(DSS_DATA15), ? ? ? (IDIS | PTD | DIS | M0)) /*DSS_DATA15*/\
+ MUX_VAL(CP(DSS_DATA16), ? ? ? (IDIS | PTD | DIS | M0)) /*DSS_DATA16*/\
+ MUX_VAL(CP(DSS_DATA17), ? ? ? (IDIS | PTD | DIS | M0)) /*DSS_DATA17*/\
+ MUX_VAL(CP(DSS_DATA18), ? ? ? (IDIS | PTD | DIS | M0)) /*DSS_DATA18*/\
+ MUX_VAL(CP(DSS_DATA19), ? ? ? (IDIS | PTD | DIS | M0)) /*DSS_DATA19*/\
+ MUX_VAL(CP(DSS_DATA20), ? ? ? (IDIS | PTD | DIS | M0)) /*DSS_DATA20*/\
+ MUX_VAL(CP(DSS_DATA21), ? ? ? (IDIS | PTD | DIS | M0)) /*DSS_DATA21*/\
+ MUX_VAL(CP(DSS_DATA22), ? ? ? (IDIS | PTD | DIS | M0)) /*DSS_DATA22*/\
+ MUX_VAL(CP(DSS_DATA23), ? ? ? (IDIS | PTD | DIS | M0)) /*DSS_DATA23*/\
+ /*CAMERA*/\
+ MUX_VAL(CP(CAM_HS), ? ? ? ? ? (IEN ?| PTU | EN ?| M0)) /*CAM_HS */\
+ MUX_VAL(CP(CAM_VS), ? ? ? ? ? (IEN ?| PTU | EN ?| M0)) /*CAM_VS */\
+ MUX_VAL(CP(CAM_XCLKA), ? ? ? ? ? ? ? ?(IDIS | PTD | DIS | M0))   
/*CAM_XCLKA*/\
+ MUX_VAL(CP(CAM_PCLK), ? ? ? ? (IEN ?| PTU | EN ?| M0)) /*CAM_PCLK*/\
+ MUX_VAL(CP(CAM_FLD), ? ? ? ? ?(IDIS | PTD | DIS | M4)) /*GPIO_98*/\
+ MUX_VAL(CP(CAM_D0), ? ? ? ? ? (IEN ?| PTD | DIS | M0)) /*CAM_D0*/\
+ MUX_VAL(CP(CAM_D1), ? ? ? ? ? (IEN ?| PTD | DIS | M0)) /*CAM_D1*/\
+ MUX_VAL(CP(CAM_D2), ? ? ? ? ? (IEN ?| PTD | DIS | M0)) /*CAM_D2*/\
+ MUX_VAL(CP(CAM_D3), ? ? ? ? ? (IEN ?| PTD | DIS | M0)) /*CAM_D3*/\
+ MUX_VAL(CP(CAM_D4), ? ? ? ? ? (IEN ?| PTD | DIS | M0)) /*CAM_D4*/\
+ MUX_VAL(CP(CAM_D5), ? ? ? ? ? (IEN ?| PTD | DIS | M0)) /*CAM_D5*/\
+ MUX_VAL(CP(CAM_D6), ? ? ? ? ? (IEN ?| PTD | DIS | M0)) /*CAM_D6*/\
+ MUX_VAL(CP(CAM_D7), ? ? ? ? ? (IEN ?| PTD | DIS | M0)) /*CAM_D7*/\
+ MUX_VAL(CP(CAM_D8), ? ? ? ? ? (IEN ?| PTD | DIS | M0)) /*CAM_D8*/\
+ MUX_VAL(CP(CAM_D9), ? ? ? ? ? (IEN ?| PTD | DIS | M0)) /*CAM_D9*/\
+ MUX_VAL(CP(CAM_D10), ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*CAM_D10*/\
+ MUX_VAL(CP(CAM_D11), ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*CAM_D11*/\
+ MUX_VAL(CP(CAM_XCLKB), ? ? ? ? ? ? ? ?(IDIS | PTD | DIS | M0))   
/*CAM_XCLKB*/\
+ MUX_VAL(CP(CAM_WEN), ? ? ? ? ?(IEN ?| PTD | DIS | M4)) /*GPIO_167*/\
+ MUX_VAL(CP(CAM_STROBE), ? ? ? (IDIS | PTD | DIS | M0)) /*CAM_STROBE*/\
+ MUX_VAL(CP(CSI2_DX0), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*CSI2_DX0*/\
+ MUX_VAL(CP(CSI2_DY0), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*CSI2_DY0*/\
+ MUX_VAL(CP(CSI2_DX1), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*CSI2_DX1*/\
+ MUX_VAL(CP(CSI2_DY1), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*CSI2_DY1*/\
+ /*Audio Interface */\
+ MUX_VAL(CP(MCBSP2_FSX), ? ? ? (IEN ?| PTD | DIS | M0)) /*McBSP2_FSX*/\
+ MUX_VAL(CP(MCBSP2_CLKX), ? ? ?(IEN ?| PTD | DIS | M0)) /*McBSP2_CLKX*/\

+ MUX_VAL(CP(MCBSP2_DR), ? ? ? ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*McBSP2_DR*/\
+ MUX_VAL(CP(MCBSP2_DX), ? ? ? ? ? ? ? ?(IDIS | PTD | DIS | M0)) /*McBSP2_DX*/\
+ /*Expansion card */\

+ MUX_VAL(CP(MMC1_CLK), ? ? ? ? (IDIS | PTU | EN ?| M0)) /*MMC1_CLK*/\
+ MUX_VAL(CP(MMC1_CMD), ? ? ? ? (IEN ?| PTU | EN ?| M0)) /*MMC1_CMD*/\

+ MUX_VAL(CP(MMC1_DAT0), ? ? ? ? ? ? ? ?(IEN ?| PTU | EN ?| M0)) /*MMC1_DAT0*/\
+ MUX_VAL(CP(MMC1_DAT1), ? ? ? ? ? ? ? ?(IEN ?| PTU | EN ?| M0)) /*MMC1_DAT1*/\
+ MUX_VAL(CP(MMC1_DAT2), ? ? ? ? ? ? ? ?(IEN ?| PTU | EN ?| M0)) /*MMC1_DAT2*/\
+ MUX_VAL(CP(MMC1_DAT3), ? ? ? ? ? ? ? ?(IEN ?| PTU | EN ?| M0)) /*MMC1_DAT3*/\
+ MUX_VAL(CP(MMC1_DAT4), ? ? ? ? ? ? ? ?(IEN ?| PTU | EN ?| M0)) /*MMC1_DAT4*/\
+ MUX_VAL(CP(MMC1_DAT5), ? ? ? ? ? ? ? ?(IEN ?| PTU | EN ?| M0)) /*MMC1_DAT5*/\
+ MUX_VAL(CP(MMC1_DAT6), ? ? ? ? ? ? ? ?(IEN ?| PTU | EN ?| M0)) /*MMC1_DAT6*/\
+ MUX_VAL(CP(MMC1_DAT7), ? ? ? ? ? ? ? ?(IEN ?| PTU | EN ?| M0)) /*MMC1_DAT7*/\
+ /*Wireless LAN */\

+ MUX_VAL(CP(MMC2_CLK), ? ? ? ? (IEN ?| PTU | EN ?| M4)) /*GPIO_130*/\
+ MUX_VAL(CP(MMC2_CMD), ? ? ? ? (IEN ?| PTU | EN ?| M4)) /*GPIO_131*/\

+ MUX_VAL(CP(MMC2_DAT0), ? ? ? ? ? ? ? ?(IEN ?| PTU | EN ?| M4)) /*GPIO_132*/\
+ MUX_VAL(CP(MMC2_DAT1), ? ? ? ? ? ? ? ?(IEN ?| PTU | EN ?| M4)) /*GPIO_133*/\
+ MUX_VAL(CP(MMC2_DAT2), ? ? ? ? ? ? ? ?(IEN ?| PTU | EN ?| M4)) /*GPIO_134*/\
+ MUX_VAL(CP(MMC2_DAT3), ? ? ? ? ? ? ? ?(IEN ?| PTU | EN ?| M4)) /*GPIO_135*/\
+ MUX_VAL(CP(MMC2_DAT4), ? ? ? ? ? ? ? ?(IEN ?| PTU | EN ?| M4)) /*GPIO_136*/\
+ MUX_VAL(CP(MMC2_DAT5), ? ? ? ? ? ? ? ?(IEN ?| PTU | EN ?| M4)) /*GPIO_137*/\
+ MUX_VAL(CP(MMC2_DAT6), ? ? ? ? ? ? ? ?(IEN ?| PTU | EN ?| M4)) /*GPIO_138*/\
+ MUX_VAL(CP(MMC2_DAT7), ? ? ? ? ? ? ? ?(IEN ?| PTU | EN ?| M4)) /*GPIO_139*/\
+ /*Bluetooth*/\
+ MUX_VAL(CP(MCBSP3_DX), ? ? ? ? ? ? ? ?(IEN ?| PTD | DIS | M1)) /*UART2_CTS*/\
+ MUX_VAL(CP(MCBSP3_DR), ? ? ? ? ? ? ? ?(IDIS | PTD | DIS | M1)) /*UART2_RTS*/\

+ MUX_VAL(CP(MCBSP3_CLKX), ? ? ?(IDIS | PTD | DIS | M1)) /*UART2_TX*/\
+ MUX_VAL(CP(MCBSP3_FSX), ? ? ? (IEN ?| PTD | DIS | M1)) /*UART2_RX*/\

+ MUX_VAL(CP(UART2_CTS), ? ? ? ? ? ? ? ?(IEN ?| PTD | DIS | M4)) /*GPIO_144*/\
+ MUX_VAL(CP(UART2_RTS), ? ? ? ? ? ? ? ?(IEN ?| PTD | DIS | M4)) /*GPIO_145*/\

+ MUX_VAL(CP(UART2_TX), ? ? ? ? (IEN ?| PTD | DIS | M4)) /*GPIO_146*/\
+ MUX_VAL(CP(UART2_RX), ? ? ? ? (IEN ?| PTD | DIS | M4)) /*GPIO_147*/\

+ /*Modem Interface */\
+ MUX_VAL(CP(UART1_TX), ? ? ? ? (IDIS | PTD | DIS | M0)) /*UART1_TX*/\
+ MUX_VAL(CP(UART1_RTS), ? ? ? ? ? ? ? ?(IDIS | PTD | DIS | M4)) /*GPIO_149*/ \
+ MUX_VAL(CP(UART1_CTS), ? ? ? ? ? ? ? ?(IDIS | PTD | DIS | M4)) /*GPIO_150*/ \

+ MUX_VAL(CP(UART1_RX), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*UART1_RX*/\
+ MUX_VAL(CP(MCBSP4_CLKX), ? ? ?(IEN ?| PTD | DIS | M1)) /*SSI1_DAT_RX*/\

+ MUX_VAL(CP(MCBSP4_DR), ? ? ? ? ? ? ? ?(IEN ?| PTD | DIS | M1)) /*SSI1_FLAG_RX*/\
+ MUX_VAL(CP(MCBSP4_DX), ? ? ? ? ? ? ? ?(IEN ?| PTD | DIS | M1)) /*SSI1_RDY_RX*/\

+ MUX_VAL(CP(MCBSP4_FSX), ? ? ? (IEN ?| PTD | DIS | M1)) /*SSI1_WAKE*/\
+ MUX_VAL(CP(MCBSP1_CLKR), ? ? ?(IDIS | PTU | EN ?| M4)) /*GPIO_156*/\
+ MUX_VAL(CP(MCBSP1_FSR), ? ? ? (IDIS | PTU | EN ?| M4)) /*GPIO_157*/\

+ MUX_VAL(CP(MCBSP1_DX), ? ? ? ? ? ? ? ?(IDIS | PTD | EN ?| M4)) /*GPIO_158*/\
+ MUX_VAL(CP(MCBSP1_DR), ? ? ? ? ? ? ? ?(IDIS | PTU | EN ?| M4)) /*GPIO_159*/\

+ MUX_VAL(CP(MCBSP_CLKS), ? ? ? (IEN ?| PTU | DIS | M0)) /*McBSP_CLKS*/\
+ MUX_VAL(CP(MCBSP1_FSX), ? ? ? (IEN ?| PTD | DIS | M4)) /*GPIO_161*/\
+ MUX_VAL(CP(MCBSP1_CLKX), ? ? ?(IDIS | PTD | DIS | M4)) /*GPIO_162*/\
+ /*Serial Interface*/\
+ MUX_VAL(CP(UART3_CTS_RCTX), ? (IEN ?| PTD | EN ?| M0)) /*UART3_CTS_RCTX*/\
+ MUX_VAL(CP(UART3_RTS_SD), ? ? (IDIS | PTD | DIS | M0)) /*UART3_RTS_SD */\
+ MUX_VAL(CP(UART3_RX_IRRX), ? ?(IEN ?| PTD | DIS | M0)) /*UART3_RX_IRRX*/\
+ MUX_VAL(CP(UART3_TX_IRTX), ? ?(IDIS | PTD | DIS | M0)) /*UART3_TX_IRTX*/\
+ MUX_VAL(CP(HSUSB0_CLK), ? ? ? (IEN ?| PTD | DIS | M0)) /*HSUSB0_CLK*/\
+ MUX_VAL(CP(HSUSB0_STP), ? ? ? (IDIS | PTU | EN ?| M0)) /*HSUSB0_STP*/\
+ MUX_VAL(CP(HSUSB0_DIR), ? ? ? (IEN ?| PTD | DIS | M0)) /*HSUSB0_DIR*/\
+ MUX_VAL(CP(HSUSB0_NXT), ? ? ? (IEN ?| PTD | DIS | M0)) /*HSUSB0_NXT*/\
+ MUX_VAL(CP(HSUSB0_DATA0), ? ? (IEN ?| PTD | DIS | M0)) /*HSUSB0_DATA0*/\
+ MUX_VAL(CP(HSUSB0_DATA1), ? ? (IEN ?| PTD | DIS | M0)) /*HSUSB0_DATA1*/\
+ MUX_VAL(CP(HSUSB0_DATA2), ? ? (IEN ?| PTD | DIS | M0)) /*HSUSB0_DATA2*/\
+ MUX_VAL(CP(HSUSB0_DATA3), ? ? (IEN ?| PTD | DIS | M0)) /*HSUSB0_DATA3*/\
+ MUX_VAL(CP(HSUSB0_DATA4), ? ? (IEN ?| PTD | DIS | M0)) /*HSUSB0_DATA4*/\
+ MUX_VAL(CP(HSUSB0_DATA5), ? ? (IEN ?| PTD | DIS | M0)) /*HSUSB0_DATA5*/\
+ MUX_VAL(CP(HSUSB0_DATA6), ? ? (IEN ?| PTD | DIS | M0)) /*HSUSB0_DATA6*/\
+ MUX_VAL(CP(HSUSB0_DATA7), ? ? (IEN ?| PTD | DIS | M0)) /*HSUSB0_DATA7*/\
+ MUX_VAL(CP(I2C1_SCL), ? ? ? ? (IEN ?| PTU | EN ?| M0)) /*I2C1_SCL*/\
+ MUX_VAL(CP(I2C1_SDA), ? ? ? ? (IEN ?| PTU | EN ?| M0)) /*I2C1_SDA*/\
+ MUX_VAL(CP(I2C2_SCL), ? ? ? ? (IEN ?| PTU | EN ?| M4)) /*GPIO_168*/\
+ MUX_VAL(CP(I2C2_SDA), ? ? ? ? (IEN ?| PTU | EN ?| M4)) /*GPIO_183*/\
+ MUX_VAL(CP(I2C3_SCL), ? ? ? ? (IEN ?| PTU | EN ?| M0)) /*I2C3_SCL*/\
+ MUX_VAL(CP(I2C3_SDA), ? ? ? ? (IEN ?| PTU | EN ?| M0)) /*I2C3_SDA*/\
+ MUX_VAL(CP(I2C4_SCL), ? ? ? ? (IEN ?| PTU | EN ?| M0)) /*I2C4_SCL*/\
+ MUX_VAL(CP(I2C4_SDA), ? ? ? ? (IEN ?| PTU | EN ?| M0)) /*I2C4_SDA*/\
+ MUX_VAL(CP(HDQ_SIO), ? ? ? ? ?(IDIS | PTU | EN ?| M4)) /*GPIO_170*/\
+ MUX_VAL(CP(MCSPI1_CLK), ? ? ? (IDIS | PTU | EN ?| M0)) /*SPI1_CLK*/\
+ MUX_VAL(CP(MCSPI1_SIMO), ? ? ?(IDIS | PTU | DIS | M0)) /*SPI1_SIMO*/\
+ MUX_VAL(CP(MCSPI1_SOMI), ? ? ?(IEN ?| PTD | DIS | M0)) /*McSPI1_SOMI*/\
+ MUX_VAL(CP(MCSPI1_CS0), ? ? ? (IEN ?| PTD | EN ?| M0)) /*McSPI1_CS0*/\
+ MUX_VAL(CP(MCSPI1_CS1), ? ? ? (IDIS | PTD | EN ?| M0)) /*McSPI1_CS1*/\
+ MUX_VAL(CP(MCSPI1_CS2), ? ? ? (IDIS | PTD | DIS | M4)) /*GPIO_176*/\
+ /* USB EHCI (port 2) */\
+ MUX_VAL(CP(MCSPI1_CS3), ? ? ? (IDIS | PTU | EN ?| M0)) /*SPI1_CS3*/\
+ MUX_VAL(CP(MCSPI2_CLK), ? ? ? (IEN ?| PTU | DIS | M3)) /*HSUSB2_DATA7*/\
+ MUX_VAL(CP(MCSPI2_SIMO), ? ? ?(IEN ?| PTU | DIS | M3)) /*HSUSB2_DATA4*/\
+ MUX_VAL(CP(MCSPI2_SOMI), ? ? ?(IEN ?| PTU | DIS | M3)) /*HSUSB2_DATA5*/\
+ MUX_VAL(CP(MCSPI2_CS0), ? ? ? (IEN ?| PTU | DIS | M3)) /*HSUSB2_DATA6*/\
+ MUX_VAL(CP(MCSPI2_CS1), ? ? ? (IEN ?| PTU | DIS | M3)) /*HSUSB2_DATA3*/\
+ MUX_VAL(CP(ETK_D10_ES2), ? ? ?(IDIS | PTU | DIS | M3)) /*HSUSB2_CLK*/\
+ MUX_VAL(CP(ETK_D11_ES2), ? ? ?(IDIS | PTU | DIS | M3)) /*HSUSB2_STP*/\
+ MUX_VAL(CP(ETK_D12_ES2), ? ? ?(IEN ?| PTU | DIS | M3)) /*HSUSB2_DIR*/\
+ MUX_VAL(CP(ETK_D13_ES2), ? ? ?(IEN ?| PTU | DIS | M3)) /*HSUSB2_NXT*/\
+ MUX_VAL(CP(ETK_D14_ES2), ? ? ?(IEN ?| PTU | DIS | M3)) /*HSUSB2_DATA0*/\
+ MUX_VAL(CP(ETK_D15_ES2), ? ? ?(IEN ?| PTU | DIS | M3)) /*HSUSB2_DATA1*/\
+ /*Control and debug */\
+ MUX_VAL(CP(SYS_32K), ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*SYS_32K*/\
+ MUX_VAL(CP(SYS_CLKREQ), ? ? ? (IEN ?| PTD | DIS | M0)) /*SYS_CLKREQ*/\
+ MUX_VAL(CP(SYS_NIRQ), ? ? ? ? (IEN ?| PTU | EN ?| M0)) /*SYS_nIRQ*/\
+ MUX_VAL(CP(SYS_BOOT0), ? ? ? ? ? ? ? ?(IEN ?| PTD | DIS | M4)) /*GPIO_2*/\
+ MUX_VAL(CP(SYS_BOOT1), ? ? ? ? ? ? ? ?(IEN ?| PTD | DIS | M4)) /*GPIO_3*/\
+ MUX_VAL(CP(SYS_BOOT2), ? ? ? ? ? ? ? ?(IEN ?| PTD | DIS | M4))   
/*GPIO_4 - MMC1_WP*/\
+ MUX_VAL(CP(SYS_BOOT3), ? ? ? ? ? ? ? ?(IEN ?| PTD | DIS | M4)) /*GPIO_5*/\
+ MUX_VAL(CP(SYS_BOOT4), ? ? ? ? ? ? ? ?(IEN ?| PTD | DIS | M4)) /*GPIO_6*/\
+ MUX_VAL(CP(SYS_BOOT5), ? ? ? ? ? ? ? ?(IEN ?| PTD | DIS | M4)) /*GPIO_7*/\
+ MUX_VAL(CP(SYS_BOOT6), ? ? ? ? ? ? ? ?(IDIS | PTD | DIS | M4))   
/*GPIO_8*/ \
+ MUX_VAL(CP(SYS_OFF_MODE), ? ? (IEN ?| PTD | DIS | M0)) /*SYS_OFF_MODE*/\
+ MUX_VAL(CP(SYS_CLKOUT1), ? ? ?(IEN ?| PTD | DIS | M0)) /*SYS_CLKOUT1*/\
+ MUX_VAL(CP(SYS_CLKOUT2), ? ? ?(IEN ?| PTU | EN ?| M4)) /*GPIO_186*/\
+ MUX_VAL(CP(ETK_CLK_ES2), ? ? ?(IDIS | PTU | EN ?| M3)) /*HSUSB1_STP*/\
+ MUX_VAL(CP(ETK_CTL_ES2), ? ? ?(IDIS | PTU | EN ?| M4)) /*GPIO_13*/\
+ MUX_VAL(CP(ETK_D0_ES2), ? ? ? (IEN ?| PTU | DIS | M3)) /*HSUSB1_DATA0*/\
+ MUX_VAL(CP(ETK_D1_ES2), ? ? ? (IEN ?| PTU | DIS | M3)) /*HSUSB1_DATA1*/\
+ MUX_VAL(CP(ETK_D2_ES2), ? ? ? (IEN ?| PTU | DIS | M3)) /*HSUSB1_DATA2*/\
+ MUX_VAL(CP(ETK_D3_ES2), ? ? ? (IEN ?| PTU | DIS | M3)) /*HSUSB1_DATA7*/\
+ MUX_VAL(CP(ETK_D4_ES2), ? ? ? (IEN ?| PTU | DIS | M3)) /*HSUSB1_DATA4*/\
+ MUX_VAL(CP(ETK_D5_ES2), ? ? ? (IEN ?| PTU | DIS | M3)) /*HSUSB1_DATA5*/\
+ MUX_VAL(CP(ETK_D6_ES2), ? ? ? (IEN ?| PTU | DIS | M3)) /*HSUSB1_DATA6*/\
+ MUX_VAL(CP(ETK_D7_ES2), ? ? ? (IEN ?| PTU | DIS | M3)) /*HSUSB1_DATA3*/\
+ MUX_VAL(CP(ETK_D8_ES2), ? ? ? (IDIS | PTU | EN ?| M4)) /*GPIO_22*/\
+ MUX_VAL(CP(ETK_D9_ES2), ? ? ? (IEN ?| PTU | DIS | M3)) /*HSUSB1_NXT*/\

+ MUX_VAL(CP(D2D_MCAD1), ? ? ? ? ? ? ? ?(IEN ?| PTD | EN ?| M0)) /*d2d_mcad1*/\
+ MUX_VAL(CP(D2D_MCAD2), ? ? ? ? ? ? ? ?(IEN ?| PTD | EN ?| M0)) /*d2d_mcad2*/\
+ MUX_VAL(CP(D2D_MCAD3), ? ? ? ? ? ? ? ?(IEN ?| PTD | EN ?| M0)) /*d2d_mcad3*/\
+ MUX_VAL(CP(D2D_MCAD4), ? ? ? ? ? ? ? ?(IEN ?| PTD | EN ?| M0)) /*d2d_mcad4*/\
+ MUX_VAL(CP(D2D_MCAD5), ? ? ? ? ? ? ? ?(IEN ?| PTD | EN ?| M0)) /*d2d_mcad5*/\
+ MUX_VAL(CP(D2D_MCAD6), ? ? ? ? ? ? ? ?(IEN ?| PTD | EN ?| M0)) /*d2d_mcad6*/\
+ MUX_VAL(CP(D2D_MCAD7), ? ? ? ? ? ? ? ?(IEN ?| PTD | EN ?| M0)) /*d2d_mcad7*/\
+ MUX_VAL(CP(D2D_MCAD8), ? ? ? ? ? ? ? ?(IEN ?| PTD | EN ?| M0)) /*d2d_mcad8*/\
+ MUX_VAL(CP(D2D_MCAD9), ? ? ? ? ? ? ? ?(IEN ?| PTD | EN ?| M0)) /*d2d_mcad9*/\

+ MUX_VAL(CP(D2D_MCAD10), ? ? ? (IEN ?| PTD | EN ?| M0)) /*d2d_mcad10*/\
+ MUX_VAL(CP(D2D_MCAD11), ? ? ? (IEN ?| PTD | EN ?| M0)) /*d2d_mcad11*/\
+ MUX_VAL(CP(D2D_MCAD12), ? ? ? (IEN ?| PTD | EN ?| M0)) /*d2d_mcad12*/\
+ MUX_VAL(CP(D2D_MCAD13), ? ? ? (IEN ?| PTD | EN ?| M0)) /*d2d_mcad13*/\
+ MUX_VAL(CP(D2D_MCAD14), ? ? ? (IEN ?| PTD | EN ?| M0)) /*d2d_mcad14*/\
+ MUX_VAL(CP(D2D_MCAD15), ? ? ? (IEN ?| PTD | EN ?| M0)) /*d2d_mcad15*/\
+ MUX_VAL(CP(D2D_MCAD16), ? ? ? (IEN ?| PTD | EN ?| M0)) /*d2d_mcad16*/\
+ MUX_VAL(CP(D2D_MCAD17), ? ? ? (IEN ?| PTD | EN ?| M0)) /*d2d_mcad17*/\
+ MUX_VAL(CP(D2D_MCAD18), ? ? ? (IEN ?| PTD | EN ?| M0)) /*d2d_mcad18*/\
+ MUX_VAL(CP(D2D_MCAD19), ? ? ? (IEN ?| PTD | EN ?| M0)) /*d2d_mcad19*/\
+ MUX_VAL(CP(D2D_MCAD20), ? ? ? (IEN ?| PTD | EN ?| M0)) /*d2d_mcad20*/\
+ MUX_VAL(CP(D2D_MCAD21), ? ? ? (IEN ?| PTD | EN ?| M0)) /*d2d_mcad21*/\
+ MUX_VAL(CP(D2D_MCAD22), ? ? ? (IEN ?| PTD | EN ?| M0)) /*d2d_mcad22*/\
+ MUX_VAL(CP(D2D_MCAD23), ? ? ? (IEN ?| PTD | EN ?| M0)) /*d2d_mcad23*/\
+ MUX_VAL(CP(D2D_MCAD24), ? ? ? (IEN ?| PTD | EN ?| M0)) /*d2d_mcad24*/\
+ MUX_VAL(CP(D2D_MCAD25), ? ? ? (IEN ?| PTD | EN ?| M0)) /*d2d_mcad25*/\
+ MUX_VAL(CP(D2D_MCAD26), ? ? ? (IEN ?| PTD | EN ?| M0)) /*d2d_mcad26*/\
+ MUX_VAL(CP(D2D_MCAD27), ? ? ? (IEN ?| PTD | EN ?| M0)) /*d2d_mcad27*/\
+ MUX_VAL(CP(D2D_MCAD28), ? ? ? (IEN ?| PTD | EN ?| M0)) /*d2d_mcad28*/\
+ MUX_VAL(CP(D2D_MCAD29), ? ? ? (IEN ?| PTD | EN ?| M0)) /*d2d_mcad29*/\
+ MUX_VAL(CP(D2D_MCAD30), ? ? ? (IEN ?| PTD | EN ?| M0)) /*d2d_mcad30*/\
+ MUX_VAL(CP(D2D_MCAD31), ? ? ? (IEN ?| PTD | EN ?| M0)) /*d2d_mcad31*/\
+ MUX_VAL(CP(D2D_MCAD32), ? ? ? (IEN ?| PTD | EN ?| M0)) /*d2d_mcad32*/\
+ MUX_VAL(CP(D2D_MCAD33), ? ? ? (IEN ?| PTD | EN ?| M0)) /*d2d_mcad33*/\
+ MUX_VAL(CP(D2D_MCAD34), ? ? ? (IEN ?| PTD | EN ?| M0)) /*d2d_mcad34*/\
+ MUX_VAL(CP(D2D_MCAD35), ? ? ? (IEN ?| PTD | EN ?| M0)) /*d2d_mcad35*/\
+ MUX_VAL(CP(D2D_MCAD36), ? ? ? (IEN ?| PTD | EN ?| M0)) /*d2d_mcad36*/\
+ MUX_VAL(CP(D2D_CLK26MI), ? ? ?(IEN ?| PTD | DIS | M0)) /*d2d_clk26mi*/\
+ MUX_VAL(CP(D2D_NRESPWRON), ? ?(IEN ?| PTD | EN ?| M0)) /*d2d_nrespwron*/\
+ MUX_VAL(CP(D2D_NRESWARM), ? ? (IEN ?| PTU | EN ?| M0)) /*d2d_nreswarm */\
+ MUX_VAL(CP(D2D_ARM9NIRQ), ? ? (IEN ?| PTD | DIS | M0)) /*d2d_arm9nirq */\
+ MUX_VAL(CP(D2D_UMA2P6FIQ), ? ?(IEN ?| PTD | DIS | M0)) /*d2d_uma2p6fiq*/\

+ MUX_VAL(CP(D2D_SPINT), ? ? ? ? ? ? ? ?(IEN ?| PTD | EN ?| M0)) /*d2d_spint*/\
+ MUX_VAL(CP(D2D_FRINT), ? ? ? ? ? ? ? ?(IEN ?| PTD | EN ?| M0)) /*d2d_frint*/\

+ MUX_VAL(CP(D2D_DMAREQ0), ? ? ?(IEN ?| PTD | DIS | M0)) /*d2d_dmareq0*/\
+ MUX_VAL(CP(D2D_DMAREQ1), ? ? ?(IEN ?| PTD | DIS | M0)) /*d2d_dmareq1*/\
+ MUX_VAL(CP(D2D_DMAREQ2), ? ? ?(IEN ?| PTD | DIS | M0)) /*d2d_dmareq2*/\
+ MUX_VAL(CP(D2D_DMAREQ3), ? ? ?(IEN ?| PTD | DIS | M0)) /*d2d_dmareq3*/\
+ MUX_VAL(CP(D2D_N3GTRST), ? ? ?(IEN ?| PTD | DIS | M0)) /*d2d_n3gtrst*/\
+ MUX_VAL(CP(D2D_N3GTDI), ? ? ? (IEN ?| PTD | DIS | M0)) /*d2d_n3gtdi*/\
+ MUX_VAL(CP(D2D_N3GTDO), ? ? ? (IEN ?| PTD | DIS | M0)) /*d2d_n3gtdo*/\
+ MUX_VAL(CP(D2D_N3GTMS), ? ? ? (IEN ?| PTD | DIS | M0)) /*d2d_n3gtms*/\
+ MUX_VAL(CP(D2D_N3GTCK), ? ? ? (IEN ?| PTD | DIS | M0)) /*d2d_n3gtck*/\
+ MUX_VAL(CP(D2D_N3GRTCK), ? ? ?(IEN ?| PTD | DIS | M0)) /*d2d_n3grtck*/\
+ MUX_VAL(CP(D2D_MSTDBY), ? ? ? (IEN ?| PTU | EN ?| M0)) /*d2d_mstdby*/\
+ MUX_VAL(CP(D2D_SWAKEUP), ? ? ?(IEN ?| PTD | EN ?| M0)) /*d2d_swakeup*/\
+ MUX_VAL(CP(D2D_IDLEREQ), ? ? ?(IEN ?| PTD | DIS | M0)) /*d2d_idlereq*/\
+ MUX_VAL(CP(D2D_IDLEACK), ? ? ?(IEN ?| PTU | EN ?| M0)) /*d2d_idleack*/\
+ MUX_VAL(CP(D2D_MWRITE), ? ? ? (IEN ?| PTD | DIS | M0)) /*d2d_mwrite*/\
+ MUX_VAL(CP(D2D_SWRITE), ? ? ? (IEN ?| PTD | DIS | M0)) /*d2d_swrite*/\

+ MUX_VAL(CP(D2D_MREAD), ? ? ? ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*d2d_mread*/\
+ MUX_VAL(CP(D2D_SREAD), ? ? ? ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*d2d_sread*/\

+ MUX_VAL(CP(D2D_MBUSFLAG), ? ? (IEN ?| PTD | DIS | M0)) /*d2d_mbusflag*/\
+ MUX_VAL(CP(D2D_SBUSFLAG), ? ? (IEN ?| PTD | DIS | M0)) /*d2d_sbusflag*/\
Quoted 8 lines
Quoted 4 lines

+ MUX_VAL(CP(SDRC_CKE0), ? ? ? ? ? ? ? ?(IDIS | PTU | EN ?| M0)) /*sdrc_cke0*/\
+ MUX_VAL(CP(SDRC_CKE1), ? ? ? ? ? ? ? ?(IDIS | PTU | EN ?| M0)) /*sdrc_cke1*/

one more reason why the mux needs a big change in mux handling :( I think we will end up with 1/2 a dozen crazy and code repetition for each board... Arrggghhh...

There are a couple subtle differences. For now, we have to use the format available.

Quoted 347 lines
Quoted 347 lines
board/omap3/kboc/kboc.h new file +2 -0
+
+#endif
include/configs/omap3_kboc.h new file +67 -0
new file mode 100644
index 0000000..8a59612
@@ -0,0 +1,317 @@
+/*
+ * (C) Copyright 2009
+ * KwikByte <www.kwikbyte.com>
+ *
+ * Author :
+ * ?Christian Owens <[email protected]>
+ *
+ * Configuration settings for the KwikByte OMAP3530 KBOC Module.
+ *
+ * Derived from the following:
+ *
+ * (C) Copyright 2006-2008
+ * Texas Instruments.
+ * Richard Woodruff <[email protected]>
+ * Syed Mohammed Khasim <[email protected]>
+ *
+ * Configuration settings for the TI OMAP3530 Beagle board.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. ? ? ? ? See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+#include <asm/sizes.h>
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_ARMCORTEXA8 ? ? 1 ? ? ? /* This is an ARM V7 CPU core */
+#define CONFIG_OMAP ? ? ? ? ? ? ? ? ? ?1 ? ? ? /* in a TI OMAP core */
+#define CONFIG_OMAP34XX ? ? ? ? ? ? ? ?1 ? ? ? /* which is a 34XX */
+#define CONFIG_OMAP3430 ? ? ? ? ? ? ? ?1 ? ? ? /* which is in a 3430 */
+#define CONFIG_OMAP3_KBOC ? ? ?1 ? ? ? /* working with KBOC */
+
+#include <asm/arch/cpu.h> ? ? ? ? ? ? ?/* get chip and board defs */
+#include <asm/arch/omap3.h>
+
+/*
+ * Display CPU and Board information
+ */
+#define CONFIG_DISPLAY_CPUINFO ? ? ? ? 1
+#define CONFIG_DISPLAY_BOARDINFO ? ? ? 1
+
+/* Clock Defines */
+#define V_OSCK ? ? ? ? ? ? ? ? 26000000 ? ? ? ?/* Clock output from T2 */
+#define V_SCLK ? ? ? ? ? ? ? ? (V_OSCK >> 1)
+
+#undef CONFIG_USE_IRQ ? ? ? ? ? ? ? ? ? ? ? ? ?/* no support for IRQs */
+#define CONFIG_MISC_INIT_R
+
+#define CONFIG_CMDLINE_TAG ? ? ? ? ? ? 1 ? ? ? /* enable passing   

of ATAGs */

include/configs/omap3_kboc.h new file +8 -0
+#define CONFIG_SETUP_MEMORY_TAGS ? ? ? 1
+#define CONFIG_INITRD_TAG ? ? ? ? ? ? ?1
+#define CONFIG_REVISION_TAG ? ? ? ? ? ?1
+
+/*
+ * Size of malloc() pool
+ */
+#define CONFIG_ENV_SIZE ? ? ? ? ? ? ? ? ? ? ? ?SZ_128K /* Total   

Size Environment */
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? /* Sector */

include/configs/omap3_kboc.h new file +12 -0
+#define CONFIG_SYS_MALLOC_LEN ? ? ? ? ?(CONFIG_ENV_SIZE + SZ_128K)
+#define CONFIG_SYS_GBL_DATA_SIZE ? ? ? 128 ? ? /* bytes reserved for */
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? /* initial data */
+
+/*
+ * Hardware drivers
+ */
+
+/*
+ * NS16550 Configuration
+ */
+#define V_NS16550_CLK ? ? ? ? ? ? ? ? ?48000000 ? ? ? ?/* 48MHz   

(APLL96/2) */

include/configs/omap3_kboc.h new file +61 -0
+
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE ? ?(-4)
+#define CONFIG_SYS_NS16550_CLK ? ? ? ? V_NS16550_CLK
+
+/*
+ * select serial console configuration
+ */
+#define CONFIG_CONS_INDEX ? ? ? ? ? ? ?3
+#define CONFIG_SYS_NS16550_COM3 ? ? ? ? ? ? ? ?OMAP34XX_UART3
+#define CONFIG_SERIAL3 ? ? ? ? ? ? ? ? 3 ? ? ? /* UART3 on KBOC Rev 0.90 */
+
+/* allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+#define CONFIG_BAUDRATE ? ? ? ? ? ? ? ? ? ? ? ?115200
+#define CONFIG_SYS_BAUDRATE_TABLE ? ? ?{4800, 9600, 19200, 38400, 57600,\
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? 115200}
+#define CONFIG_MMC ? ? ? ? ? ? ? ? ? ? 1
+#define CONFIG_OMAP3_MMC ? ? ? ? ? ? ? 1
+#define CONFIG_DOS_PARTITION ? ? ? ? ? 1
+
+/* commands to include */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_EXT2 ? ? ? ? ? ? ? ?/* EXT2 Support ? ? ? ? ? ? ? ? */
+#define CONFIG_CMD_FAT ? ? ? ? /* FAT support ? ? ? ? ? ? ? ? ?*/
+#define CONFIG_CMD_JFFS2 ? ? ? /* JFFS2 Support ? ? ? ? ? ? ? ?*/
+#define CONFIG_CMD_MTDPARTS ? ?/* Enable MTD parts commands */
+#define CONFIG_MTD_DEVICE ? ? ?/* needed for mtdparts commands */
+#define MTDIDS_DEFAULT ? ? ? ? ? ? ? ? "nand0=nand"
+#define MTDPARTS_DEFAULT ? ? ? ? ? ? ? "mtdparts=nand:512k(x-loader),"\
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? "1920k(u-boot),128k(u-boot-env),"\
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? "4m(kernel),-(fs)"
+
+#define CONFIG_CMD_I2C ? ? ? ? /* I2C serial bus support ? ? ? */
+#define CONFIG_CMD_MMC ? ? ? ? /* MMC support ? ? ? ? ? ? ? ? ?*/
+#define CONFIG_CMD_NAND ? ? ? ? ? ? ? ?/* NAND support ? ? ? ? ? ? ? ? */
+
+#undef CONFIG_CMD_FLASH ? ? ? ? ? ? ? ?/* flinfo, erase, protect ? ? ? */
+#undef CONFIG_CMD_FPGA ? ? ? ? /* FPGA configuration Support ? */
+#undef CONFIG_CMD_IMI ? ? ? ? ?/* iminfo ? ? ? ? ? ? ? ? ? ? ? */
+#undef CONFIG_CMD_IMLS ? ? ? ? /* List all found images ? ? ? ?*/
+#undef CONFIG_CMD_NET ? ? ? ? ?/* bootp, tftpboot, rarpboot ? ?*/
+#undef CONFIG_CMD_NFS ? ? ? ? ?/* NFS support ? ? ? ? ? ? ? ? ?*/
+
+#define CONFIG_SYS_NO_FLASH
+#define CONFIG_SYS_I2C_SPEED ? ? ? ? ? 100000
+#define CONFIG_SYS_I2C_SLAVE ? ? ? ? ? 1
+#define CONFIG_SYS_I2C_BUS ? ? ? ? ? ? 0
+#define CONFIG_SYS_I2C_BUS_SELECT ? ? ?1
+#define CONFIG_DRIVER_OMAP34XX_I2C ? ? 1
+
+/*
+ * Board NAND Info.
+ */
+#define CONFIG_NAND_OMAP_GPMC
+#define CONFIG_SYS_NAND_ADDR ? ? ? ? ? NAND_BASE ? ? ? /* physical  
 address */
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? /* to access nand */
+#define CONFIG_SYS_NAND_BASE ? ? ? ? ? NAND_BASE ? ? ? /* physical  
 address */
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? /* to   

access nand at */
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? /* CS0 */

include/configs/omap3_kboc.h new file +3 -0
+#define GPMC_NAND_ECC_LP_x16_LAYOUT ? ?1
+
+#define CONFIG_SYS_MAX_NAND_DEVICE ? ? 1 ? ? ? ? ? ? ? /* Max   

number of NAND */
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? /* devices */

include/configs/omap3_kboc.h new file +62 -0
+
+#define CONFIG_JFFS2_NAND
+/* nand device jffs2 lives on */
+#define CONFIG_JFFS2_DEV ? ? ? ? ? ? ? "nand0"
+/* start of jffs2 partition */
+#define CONFIG_JFFS2_PART_OFFSET ? ? ? 0x680000
+#define CONFIG_JFFS2_PART_SIZE ? ? ? ? 0xf980000 ? ? ? /* size of jffs2 */
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? /* partition */
+
+/* Environment information */
+#define CONFIG_BOOTDELAY ? ? ? ? ? ? ? 3
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ ? ? ? "loadaddr=0x82000000\0" \
+ ? ? ? "console=ttyS2,115200n8\0" \
+ ? ? ? "videomode=1024x768 at 60,vxres=1024,vyres=768\0" \
+ ? ? ? "videospec=omapfb:vram:2M,vram:4M\0" \
+ ? ? ? "mmcargs=setenv bootargs console=${console} " \
+ ? ? ? ? ? ? ? "video=${videospec},mode:${videomode} " \
+ ? ? ? ? ? ? ? "root=/dev/mmcblk0p2 rw " \
+ ? ? ? ? ? ? ? "rootfstype=ext3 rootwait " \
+ ? ? ? ? ? ? ? "${optargs}\0" \
+ ? ? ? "nandargs=setenv bootargs console=${console} " \
+ ? ? ? ? ? ? ? "video=${videospec},mode:${videomode} " \
+ ? ? ? ? ? ? ? "root=/dev/mtdblock4 rw " \
+ ? ? ? ? ? ? ? "rootfstype=jffs2 " \
+ ? ? ? ? ? ? ? "${optargs}\0" \
+ ? ? ? "loadbootscript=fatload mmc 0 ${loadaddr} boot.scr\0" \
+ ? ? ? "bootscript=echo Running bootscript from mmc ...; " \
+ ? ? ? ? ? ? ? "source ${loadaddr}\0" \
+ ? ? ? "loaduimage=fatload mmc 0 ${loadaddr} uImage\0" \
+ ? ? ? "mmcboot=echo Booting from mmc ...; " \
+ ? ? ? ? ? ? ? "run mmcargs; " \
+ ? ? ? ? ? ? ? "bootm ${loadaddr}\0" \
+ ? ? ? "nandboot=echo Booting from nand ...; " \
+ ? ? ? ? ? ? ? "run nandargs; " \
+ ? ? ? ? ? ? ? "nand read ${loadaddr} 280000 400000; " \
+ ? ? ? ? ? ? ? "bootm ${loadaddr}\0" \
+
+#define CONFIG_BOOTCOMMAND \
+ ? ? ? "if mmc init; then " \
+ ? ? ? ? ? ? ? "if run loadbootscript; then " \
+ ? ? ? ? ? ? ? ? ? ? ? "run bootscript; " \
+ ? ? ? ? ? ? ? "else " \
+ ? ? ? ? ? ? ? ? ? ? ? "if run loaduimage; then " \
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? "run mmcboot; " \
+ ? ? ? ? ? ? ? ? ? ? ? "else run nandboot; " \
+ ? ? ? ? ? ? ? ? ? ? ? "fi; " \
+ ? ? ? ? ? ? ? "fi; " \
+ ? ? ? "else run nandboot; fi"
+
+#define CONFIG_AUTO_COMPLETE ? ? ? ? ? 1
+/*
+ * Miscellaneous configurable options
+ */
+#define V_PROMPT ? ? ? ? ? ? ? ? ? ? ? "OMAP3_KBOC # "
+
+#define CONFIG_SYS_LONGHELP ? ? ? ? ? ?/* undef to save memory */
+#define CONFIG_SYS_HUSH_PARSER ? ? ? ? /* use "hush" command parser */
+#define CONFIG_SYS_PROMPT_HUSH_PS2 ? ? "> "
+#define CONFIG_SYS_PROMPT ? ? ? ? ? ? ?V_PROMPT
+#define CONFIG_SYS_CBSIZE ? ? ? ? ? ? ?256 ? ? /* Console I/O   

Buffer Size */

include/configs/omap3_kboc.h new file +4 -0
+/* Print Buffer Size */
+#define CONFIG_SYS_PBSIZE ? ? ? ? ? ? ?(CONFIG_SYS_CBSIZE + \
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_MAXARGS ? ? ? ? ? ? 16 ? ? ?/* max number of   

command args */

include/configs/omap3_kboc.h new file +4 -0
+/* Boot Argument Buffer Size */
+#define CONFIG_SYS_BARGSIZE ? ? ? ? ? ?(CONFIG_SYS_CBSIZE)
+
+#define CONFIG_SYS_MEMTEST_START ? ? ? (OMAP34XX_SDRC_CS0) ? ? /*   

memtest */
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? /* works on */

include/configs/omap3_kboc.h new file +4 -0
+#define CONFIG_SYS_MEMTEST_END ? ? ? ? (OMAP34XX_SDRC_CS0 + \
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? 0x01F00000) /* 31MB */
+
+#define CONFIG_SYS_LOAD_ADDR ? ? ? ? ? (OMAP34XX_SDRC_CS0) ? ? /*   

default */
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? /* load address */

include/configs/omap3_kboc.h new file +8 -0
+
+/*
+ * OMAP3 has 12 GP timers, they can be driven by the system clock
+ * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK).
+ * This rate is divided by a local divisor.
+ */
+#define CONFIG_SYS_TIMERBASE ? ? ? ? ? (OMAP34XX_GPT2)
+#define CONFIG_SYS_PTV ? ? ? ? ? ? ? ? 2 ? ? ? /* Divisor:   

2^(PTV+1) => 8 */

include/configs/omap3_kboc.h new file +17 -0
+#define CONFIG_SYS_HZ ? ? ? ? ? ? ? ? ?1000
+
+/*-----------------------------------------------------------------------
+ * Stack sizes
+ *
+ * The stack sizes are set up in start.S using the settings below
+ */
+#define CONFIG_STACKSIZE ? ? ? SZ_128K /* regular stack */
+#ifdef CONFIG_USE_IRQ
+#define CONFIG_STACKSIZE_IRQ ? SZ_4K ? /* IRQ stack */
+#define CONFIG_STACKSIZE_FIQ ? SZ_4K ? /* FIQ stack */
+#endif
+
+/*-----------------------------------------------------------------------
+ * Physical Memory Map
+ */
+#define CONFIG_NR_DRAM_BANKS ? 2 ? ? ? /* CS1 may or may not be   

populated */

include/configs/omap3_kboc.h new file +18 -0
+#define PHYS_SDRAM_1 ? ? ? ? ? OMAP34XX_SDRC_CS0
+#define PHYS_SDRAM_1_SIZE ? ? ?SZ_32M ?/* at least 32 meg */
+#define PHYS_SDRAM_2 ? ? ? ? ? OMAP34XX_SDRC_CS1
+
+/* SDRAM Bank Allocation method */
+#define SDRC_R_B_C ? ? ? ? ? ? 1
+
+/*-----------------------------------------------------------------------
+ * FLASH and environment organization
+ */
+
+/* **** PISMO SUPPORT *** */
+
+/* Configure the PISMO */
+#define PISMO1_NAND_SIZE ? ? ? ? ? ? ? GPMC_SIZE_128M
+#define PISMO1_ONEN_SIZE ? ? ? ? ? ? ? GPMC_SIZE_128M
+
+#define CONFIG_SYS_MAX_FLASH_SECT ? ? ?520 ? ? /* max number of   

sectors on */
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? /* one chip */ +#define CONFIG_SYS_MAX_FLASH_BANKS ? ? 2 ? ? ? /* max number of flash banks */

include/configs/omap3_kboc.h new file +10 -0
+#define CONFIG_SYS_MONITOR_LEN ? ? ? ? SZ_256K /* Reserve 2 sectors */
+
+#define CONFIG_SYS_FLASH_BASE ? ? ? ? ?boot_flash_base
+
+/* Monitor at start of flash */
+#define CONFIG_SYS_MONITOR_BASE ? ? ? ? ? ? ? ?CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_ONENAND_BASE ? ? ? ? ? ? ? ?ONENAND_MAP
+
+#define CONFIG_ENV_IS_IN_NAND ? ? ? ? ?1
+#define ONENAND_ENV_OFFSET ? ? ? ? ? ? 0x260000 /* environment   

starts here */
+#define SMNAND_ENV_OFFSET ? ? ? ? ? ? ?0x260000 /* environment starts here */

include/configs/omap3_kboc.h new file +31 -1
+
+#define CONFIG_SYS_ENV_SECT_SIZE ? ? ? boot_flash_sec
+#define CONFIG_ENV_OFFSET ? ? ? ? ? ? ?boot_flash_off
+#define CONFIG_ENV_ADDR ? ? ? ? ? ? ? ? ? ? ? ?SMNAND_ENV_OFFSET
+
+/*-----------------------------------------------------------------------
+ * CFI FLASH driver setup
+ */
+/* timeout values are in ticks */
+#define CONFIG_SYS_FLASH_ERASE_TOUT ? ?(100 * CONFIG_SYS_HZ)
+#define CONFIG_SYS_FLASH_WRITE_TOUT ? ?(100 * CONFIG_SYS_HZ)
+
+/* Flash banks JFFS2 should use */
+#define CONFIG_SYS_MAX_MTD_BANKS ? ? ? (CONFIG_SYS_MAX_FLASH_BANKS + \
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? CONFIG_SYS_MAX_NAND_DEVICE)
+#define CONFIG_SYS_JFFS2_MEM_NAND
+/* use flash_info[2] */
+#define CONFIG_SYS_JFFS2_FIRST_BANK ? ?CONFIG_SYS_MAX_FLASH_BANKS
+#define CONFIG_SYS_JFFS2_NUM_BANKS ? ? 1
+
+#ifndef __ASSEMBLY__
+extern gpmc_csx_t *nand_cs_base;
+extern gpmc_t *gpmc_cfg_base;
+extern unsigned int boot_flash_base;
+extern volatile unsigned int boot_flash_env_addr;
+extern unsigned int boot_flash_off;
+extern unsigned int boot_flash_sec;
+extern unsigned int boot_flash_type;
+#endif
+
+#endif /* __CONFIG_H */
--

1.5.4.3

Quoted 6 lines
Quoted 5 lines

_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot

Thanks for the comments. If my planned updates are acceptable, I will make the changes and submit a new patch.

#3 lore raw

PATCH 1/1 Add support for the KwikByte KBOC OMAP35xx board

In reply to Nishanth Menon

Could you regenerate it with the following option
git format-patch -M -B -C

Quoted 14 lines
Quoted 6 lines

+ ? ? ? /* Configure GPIOs to output */
+ ? ? ? writel(~(GPIO23 | GPIO17 | GPIO12 | GPIO11 | GPIO10 | GPIO8 | GPIO2),
+ ? ? ? ? ? ? ? &gpio6_base->oe);
+ ? ? ? writel(~(GPIO31 | GPIO30 | GPIO29 | GPIO28 | GPIO22 | GPIO21 |
+ ? ? ? ? ? ? ? GPIO13 | GPIO12), &gpio5_base->oe);
+ ? ? ? writel(~(GPIO22 | GPIO13), &gpio1_base->oe);

Quoted 8 lines

+
+ ? ? ? /* Set GPIOs */
+ ? ? ? writel(GPIO23 | GPIO17 | GPIO10 | GPIO8 | GPIO2,
+ ? ? ? ? ? ? ? &gpio6_base->setdataout);
+ ? ? ? writel(GPIO31 | GPIO29 | GPIO28 | GPIO22 | GPIO21 | GPIO13 | GPIO12,
+ ? ? ? ? ? ? ? &gpio5_base->setdataout);
+ ? ? ? writel(GPIO22 | GPIO13,
+ ? ? ? ? ? ? ? &gpio1_base->setdataout);

Quoted 3 lines

Aieeeee....... what are these gpios and why do they need to be set high?

normally you might want to do setdataout followed by oe?

btw we have a gpio API now please use it

Quoted 9 lines
Quoted 9 lines
board/omap3/kboc/kboc.c new file +9 -0
+
+ ? ? ? dieid_num_r();
+
+ ? ? ? return 0;
+}
+
+/*
+ * Routine: set_muxconf_regs
+ * Description: Setting up the configuration Mux registers specific to the
Quoted 8 lines

board/omap3/kboc/kboc.h

Quoted 8 lines

+ * ? ? ? ? ? ? hardware. Many pins need to be moved from protect to primary
+ * ? ? ? ? ? ? mode.
+ */

board/omap3/kboc/kboc.c new file +4 -0
+void set_muxconf_regs(void)
+{
+ ? ? ? MUX_KBOC();
+}
board/omap3/kboc/kboc.h +0 -0

please create you own vendor dirent

Quoted 77 lines
Quoted 36 lines

new file mode 100644
index 0000000..41c3b9e

board/omap3/kboc/kboc.h new file +31 -0
@@ -0,0 +1,382 @@
+/*
+ * (C) Copyright 2009
+ * KwikByte <www.kwikbyte.com>
+ *
+ * Author :
+ * ?Christian Owens <[email protected]>
+ *
+ * Derived from the following:
+ *
+ * (C) Copyright 2008
+ * Dirk Behme <[email protected]>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. ?See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+#ifndef _KBOC_H_

board/omap3/kboc/kboc.h line 41

Quoted 10 lines
board/omap3/kboc/kboc.h new file +10 -0
+#define _KBOC_H_
+
+const omap3_sysinfo sysinfo = {
+ ? ? ? DDR_STACKED,
+ ? ? ? "OMAP3 KBOC board",
+#if defined(CONFIG_ENV_IS_IN_ONENAND)
+ ? ? ? "OneNAND",
+#else
+ ? ? ? "NAND",
+#endif

err... CONFIG_ENV_IS_IN_NAND is defined as 1 in config header.. means never support onenand?

Quoted 28 lines
board/omap3/kboc/kboc.h new file +28 -0
+};
+
+/*
+ * IEN ?- Input Enable
+ * IDIS - Input Disable
+ * PTD ?- Pull type Down
+ * PTU ?- Pull type Up
+ * DIS ?- Pull type selection is inactive
+ * EN ? - Pull type selection is active
+ * M0 ? - Mode 0
+ * The commented string gives the final mux configuration for that pin
+ */
+#define MUX_KBOC() \
+ /*SDRC*/\
+ MUX_VAL(CP(SDRC_D0), ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*SDRC_D0*/\
+ MUX_VAL(CP(SDRC_D1), ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*SDRC_D1*/\
+ MUX_VAL(CP(SDRC_D2), ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*SDRC_D2*/\
+ MUX_VAL(CP(SDRC_D3), ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*SDRC_D3*/\
+ MUX_VAL(CP(SDRC_D4), ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*SDRC_D4*/\
+ MUX_VAL(CP(SDRC_D5), ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*SDRC_D5*/\
+ MUX_VAL(CP(SDRC_D6), ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*SDRC_D6*/\
+ MUX_VAL(CP(SDRC_D7), ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*SDRC_D7*/\
+ MUX_VAL(CP(SDRC_D8), ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*SDRC_D8*/\
+ MUX_VAL(CP(SDRC_D9), ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*SDRC_D9*/\
+ MUX_VAL(CP(SDRC_D10), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*SDRC_D10*/\
+ MUX_VAL(CP(SDRC_D11), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*SDRC_D11*/\
+ MUX_VAL(CP(SDRC_D12), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*SDRC_D12*/\
+ MUX_VAL(CP(SDRC_D13), ? ? ? ? (IEN ?| PTD | DIS | M0)) /*SDRC_D13*/\

<snip>

Quoted 24 lines
Quoted 15 lines

+ MUX_VAL(CP(D2D_FRINT), ? ? ? ? ? ? ? ?(IEN ?| PTD | EN ?| M0)) /*d2d_frint*/\

+ MUX_VAL(CP(D2D_DMAREQ0), ? ? ?(IEN ?| PTD | DIS | M0)) /*d2d_dmareq0*/\
+ MUX_VAL(CP(D2D_DMAREQ1), ? ? ?(IEN ?| PTD | DIS | M0)) /*d2d_dmareq1*/\
+ MUX_VAL(CP(D2D_DMAREQ2), ? ? ?(IEN ?| PTD | DIS | M0)) /*d2d_dmareq2*/\
+ MUX_VAL(CP(D2D_DMAREQ3), ? ? ?(IEN ?| PTD | DIS | M0)) /*d2d_dmareq3*/\
+ MUX_VAL(CP(D2D_N3GTRST), ? ? ?(IEN ?| PTD | DIS | M0)) /*d2d_n3gtrst*/\
+ MUX_VAL(CP(D2D_N3GTDI), ? ? ? (IEN ?| PTD | DIS | M0)) /*d2d_n3gtdi*/\
+ MUX_VAL(CP(D2D_N3GTDO), ? ? ? (IEN ?| PTD | DIS | M0)) /*d2d_n3gtdo*/\
+ MUX_VAL(CP(D2D_N3GTMS), ? ? ? (IEN ?| PTD | DIS | M0)) /*d2d_n3gtms*/\
+ MUX_VAL(CP(D2D_N3GTCK), ? ? ? (IEN ?| PTD | DIS | M0)) /*d2d_n3gtck*/\
+ MUX_VAL(CP(D2D_N3GRTCK), ? ? ?(IEN ?| PTD | DIS | M0)) /*d2d_n3grtck*/\
+ MUX_VAL(CP(D2D_MSTDBY), ? ? ? (IEN ?| PTU | EN ?| M0)) /*d2d_mstdby*/\
+ MUX_VAL(CP(D2D_SWAKEUP), ? ? ?(IEN ?| PTD | EN ?| M0)) /*d2d_swakeup*/\
+ MUX_VAL(CP(D2D_IDLEREQ), ? ? ?(IEN ?| PTD | DIS | M0)) /*d2d_idlereq*/\
+ MUX_VAL(CP(D2D_IDLEACK), ? ? ?(IEN ?| PTU | EN ?| M0)) /*d2d_idleack*/\
Quoted 8 lines
+ MUX_VAL(CP(D2D_MWRITE), ? ? ? (IEN ?| PTD | DIS | M0)) /*d2d_mwrite*/\
+ MUX_VAL(CP(D2D_SWRITE), ? ? ? (IEN ?| PTD | DIS | M0)) /*d2d_swrite*/\
+ MUX_VAL(CP(D2D_MREAD), ? ? ? ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*d2d_mread*/\
+ MUX_VAL(CP(D2D_SREAD), ? ? ? ? ? ? ? ?(IEN ?| PTD | DIS | M0)) /*d2d_sread*/\
+ MUX_VAL(CP(D2D_MBUSFLAG), ? ? (IEN ?| PTD | DIS | M0)) /*d2d_mbusflag*/\
+ MUX_VAL(CP(D2D_SBUSFLAG), ? ? (IEN ?| PTD | DIS | M0)) /*d2d_sbusflag*/\
+ MUX_VAL(CP(SDRC_CKE0), ? ? ? ? ? ? ? ?(IDIS | PTU | EN ?| M0)) /*sdrc_cke0*/\
+ MUX_VAL(CP(SDRC_CKE1), ? ? ? ? ? ? ? ?(IDIS | PTU | EN ?| M0)) /*sdrc_cke1*/
Quoted 3 lines

one more reason why the mux needs a big change in mux handling :( I think we will end up with 1/2 a dozen crazy and code repetition for each board... Arrggghhh...

NM: yes, it's really not easy to follow here
do you plan to do it soon?

Quoted 210 lines
Quoted 210 lines
board/omap3/kboc/kboc.h new file +2 -0
+
+#endif
include/configs/omap3_kboc.h new file +202 -0
new file mode 100644
index 0000000..8a59612
@@ -0,0 +1,317 @@
+/*
+ * (C) Copyright 2009
+ * KwikByte <www.kwikbyte.com>
+ *
+ * Author :
+ * ?Christian Owens <[email protected]>
+ *
+ * Configuration settings for the KwikByte OMAP3530 KBOC Module.
+ *
+ * Derived from the following:
+ *
+ * (C) Copyright 2006-2008
+ * Texas Instruments.
+ * Richard Woodruff <[email protected]>
+ * Syed Mohammed Khasim <[email protected]>
+ *
+ * Configuration settings for the TI OMAP3530 Beagle board.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. ? ? ? ? See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+#include <asm/sizes.h>
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_ARMCORTEXA8 ? ? 1 ? ? ? /* This is an ARM V7 CPU core */
+#define CONFIG_OMAP ? ? ? ? ? ? ? ? ? ?1 ? ? ? /* in a TI OMAP core */
+#define CONFIG_OMAP34XX ? ? ? ? ? ? ? ?1 ? ? ? /* which is a 34XX */
+#define CONFIG_OMAP3430 ? ? ? ? ? ? ? ?1 ? ? ? /* which is in a 3430 */
+#define CONFIG_OMAP3_KBOC ? ? ?1 ? ? ? /* working with KBOC */
+
+#include <asm/arch/cpu.h> ? ? ? ? ? ? ?/* get chip and board defs */
+#include <asm/arch/omap3.h>
+
+/*
+ * Display CPU and Board information
+ */
+#define CONFIG_DISPLAY_CPUINFO ? ? ? ? 1
+#define CONFIG_DISPLAY_BOARDINFO ? ? ? 1
+
+/* Clock Defines */
+#define V_OSCK ? ? ? ? ? ? ? ? 26000000 ? ? ? ?/* Clock output from T2 */
+#define V_SCLK ? ? ? ? ? ? ? ? (V_OSCK >> 1)
+
+#undef CONFIG_USE_IRQ ? ? ? ? ? ? ? ? ? ? ? ? ?/* no support for IRQs */
+#define CONFIG_MISC_INIT_R
+
+#define CONFIG_CMDLINE_TAG ? ? ? ? ? ? 1 ? ? ? /* enable passing of ATAGs */
+#define CONFIG_SETUP_MEMORY_TAGS ? ? ? 1
+#define CONFIG_INITRD_TAG ? ? ? ? ? ? ?1
+#define CONFIG_REVISION_TAG ? ? ? ? ? ?1
+
+/*
+ * Size of malloc() pool
+ */
+#define CONFIG_ENV_SIZE ? ? ? ? ? ? ? ? ? ? ? ?SZ_128K /* Total Size Environment */
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? /* Sector */
+#define CONFIG_SYS_MALLOC_LEN ? ? ? ? ?(CONFIG_ENV_SIZE + SZ_128K)
+#define CONFIG_SYS_GBL_DATA_SIZE ? ? ? 128 ? ? /* bytes reserved for */
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? /* initial data */
+
+/*
+ * Hardware drivers
+ */
+
+/*
+ * NS16550 Configuration
+ */
+#define V_NS16550_CLK ? ? ? ? ? ? ? ? ?48000000 ? ? ? ?/* 48MHz (APLL96/2) */
+
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE ? ?(-4)
+#define CONFIG_SYS_NS16550_CLK ? ? ? ? V_NS16550_CLK
+
+/*
+ * select serial console configuration
+ */
+#define CONFIG_CONS_INDEX ? ? ? ? ? ? ?3
+#define CONFIG_SYS_NS16550_COM3 ? ? ? ? ? ? ? ?OMAP34XX_UART3
+#define CONFIG_SERIAL3 ? ? ? ? ? ? ? ? 3 ? ? ? /* UART3 on KBOC Rev 0.90 */
+
+/* allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+#define CONFIG_BAUDRATE ? ? ? ? ? ? ? ? ? ? ? ?115200
+#define CONFIG_SYS_BAUDRATE_TABLE ? ? ?{4800, 9600, 19200, 38400, 57600,\
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? 115200}
+#define CONFIG_MMC ? ? ? ? ? ? ? ? ? ? 1
+#define CONFIG_OMAP3_MMC ? ? ? ? ? ? ? 1
+#define CONFIG_DOS_PARTITION ? ? ? ? ? 1
+
+/* commands to include */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_EXT2 ? ? ? ? ? ? ? ?/* EXT2 Support ? ? ? ? ? ? ? ? */
+#define CONFIG_CMD_FAT ? ? ? ? /* FAT support ? ? ? ? ? ? ? ? ?*/
+#define CONFIG_CMD_JFFS2 ? ? ? /* JFFS2 Support ? ? ? ? ? ? ? ?*/
+#define CONFIG_CMD_MTDPARTS ? ?/* Enable MTD parts commands */
+#define CONFIG_MTD_DEVICE ? ? ?/* needed for mtdparts commands */
+#define MTDIDS_DEFAULT ? ? ? ? ? ? ? ? "nand0=nand"
+#define MTDPARTS_DEFAULT ? ? ? ? ? ? ? "mtdparts=nand:512k(x-loader),"\
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? "1920k(u-boot),128k(u-boot-env),"\
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? "4m(kernel),-(fs)"
+
+#define CONFIG_CMD_I2C ? ? ? ? /* I2C serial bus support ? ? ? */
+#define CONFIG_CMD_MMC ? ? ? ? /* MMC support ? ? ? ? ? ? ? ? ?*/
+#define CONFIG_CMD_NAND ? ? ? ? ? ? ? ?/* NAND support ? ? ? ? ? ? ? ? */
+
+#undef CONFIG_CMD_FLASH ? ? ? ? ? ? ? ?/* flinfo, erase, protect ? ? ? */
+#undef CONFIG_CMD_FPGA ? ? ? ? /* FPGA configuration Support ? */
+#undef CONFIG_CMD_IMI ? ? ? ? ?/* iminfo ? ? ? ? ? ? ? ? ? ? ? */
+#undef CONFIG_CMD_IMLS ? ? ? ? /* List all found images ? ? ? ?*/
+#undef CONFIG_CMD_NET ? ? ? ? ?/* bootp, tftpboot, rarpboot ? ?*/
+#undef CONFIG_CMD_NFS ? ? ? ? ?/* NFS support ? ? ? ? ? ? ? ? ?*/
+
+#define CONFIG_SYS_NO_FLASH
+#define CONFIG_SYS_I2C_SPEED ? ? ? ? ? 100000
+#define CONFIG_SYS_I2C_SLAVE ? ? ? ? ? 1
+#define CONFIG_SYS_I2C_BUS ? ? ? ? ? ? 0
+#define CONFIG_SYS_I2C_BUS_SELECT ? ? ?1
+#define CONFIG_DRIVER_OMAP34XX_I2C ? ? 1
+
+/*
+ * Board NAND Info.
+ */
+#define CONFIG_NAND_OMAP_GPMC
+#define CONFIG_SYS_NAND_ADDR ? ? ? ? ? NAND_BASE ? ? ? /* physical address */
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? /* to access nand */
+#define CONFIG_SYS_NAND_BASE ? ? ? ? ? NAND_BASE ? ? ? /* physical address */
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? /* to access nand at */
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? /* CS0 */
+#define GPMC_NAND_ECC_LP_x16_LAYOUT ? ?1
+
+#define CONFIG_SYS_MAX_NAND_DEVICE ? ? 1 ? ? ? ? ? ? ? /* Max number of NAND */
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? /* devices */
+
+#define CONFIG_JFFS2_NAND
+/* nand device jffs2 lives on */
+#define CONFIG_JFFS2_DEV ? ? ? ? ? ? ? "nand0"
+/* start of jffs2 partition */
+#define CONFIG_JFFS2_PART_OFFSET ? ? ? 0x680000
+#define CONFIG_JFFS2_PART_SIZE ? ? ? ? 0xf980000 ? ? ? /* size of jffs2 */
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? /* partition */
+
+/* Environment information */
+#define CONFIG_BOOTDELAY ? ? ? ? ? ? ? 3
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ ? ? ? "loadaddr=0x82000000\0" \
+ ? ? ? "console=ttyS2,115200n8\0" \
+ ? ? ? "videomode=1024x768 at 60,vxres=1024,vyres=768\0" \
+ ? ? ? "videospec=omapfb:vram:2M,vram:4M\0" \
+ ? ? ? "mmcargs=setenv bootargs console=${console} " \
+ ? ? ? ? ? ? ? "video=${videospec},mode:${videomode} " \
+ ? ? ? ? ? ? ? "root=/dev/mmcblk0p2 rw " \
+ ? ? ? ? ? ? ? "rootfstype=ext3 rootwait " \
+ ? ? ? ? ? ? ? "${optargs}\0" \
+ ? ? ? "nandargs=setenv bootargs console=${console} " \
+ ? ? ? ? ? ? ? "video=${videospec},mode:${videomode} " \
+ ? ? ? ? ? ? ? "root=/dev/mtdblock4 rw " \
+ ? ? ? ? ? ? ? "rootfstype=jffs2 " \
+ ? ? ? ? ? ? ? "${optargs}\0" \
+ ? ? ? "loadbootscript=fatload mmc 0 ${loadaddr} boot.scr\0" \
+ ? ? ? "bootscript=echo Running bootscript from mmc ...; " \
+ ? ? ? ? ? ? ? "source ${loadaddr}\0" \
+ ? ? ? "loaduimage=fatload mmc 0 ${loadaddr} uImage\0" \
+ ? ? ? "mmcboot=echo Booting from mmc ...; " \
+ ? ? ? ? ? ? ? "run mmcargs; " \
+ ? ? ? ? ? ? ? "bootm ${loadaddr}\0" \
+ ? ? ? "nandboot=echo Booting from nand ...; " \
+ ? ? ? ? ? ? ? "run nandargs; " \
+ ? ? ? ? ? ? ? "nand read ${loadaddr} 280000 400000; " \
+ ? ? ? ? ? ? ? "bootm ${loadaddr}\0" \
+
+#define CONFIG_BOOTCOMMAND \
+ ? ? ? "if mmc init; then " \
+ ? ? ? ? ? ? ? "if run loadbootscript; then " \
+ ? ? ? ? ? ? ? ? ? ? ? "run bootscript; " \
+ ? ? ? ? ? ? ? "else " \
+ ? ? ? ? ? ? ? ? ? ? ? "if run loaduimage; then " \
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? "run mmcboot; " \
+ ? ? ? ? ? ? ? ? ? ? ? "else run nandboot; " \
+ ? ? ? ? ? ? ? ? ? ? ? "fi; " \
Quoted 8 lines

include/configs/omap3_kboc.h

Quoted 8 lines
include/configs/omap3_kboc.h new file +8 -0
+ ? ? ? ? ? ? ? "fi; " \
+ ? ? ? "else run nandboot; fi"
+
+#define CONFIG_AUTO_COMPLETE ? ? ? ? ? 1
+/*
+ * Miscellaneous configurable options
+ */
+#define V_PROMPT ? ? ? ? ? ? ? ? ? ? ? "OMAP3_KBOC # "

no need of add V_PROMPT define
please use CONFIG_SYS_PROMPT

Quoted 9 lines

include/configs/omap3_kboc.h line 219

Quoted 9 lines
include/configs/omap3_kboc.h new file +9 -0
+
+#define CONFIG_SYS_LONGHELP ? ? ? ? ? ?/* undef to save memory */
+#define CONFIG_SYS_HUSH_PARSER ? ? ? ? /* use "hush" command parser */
+#define CONFIG_SYS_PROMPT_HUSH_PS2 ? ? "> "
+#define CONFIG_SYS_PROMPT ? ? ? ? ? ? ?V_PROMPT
+#define CONFIG_SYS_CBSIZE ? ? ? ? ? ? ?256 ? ? /* Console I/O Buffer Size */
+/* Print Buffer Size */
+#define CONFIG_SYS_PBSIZE ? ? ? ? ? ? ?(CONFIG_SYS_CBSIZE + \
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? sizeof(CONFIG_SYS_PROMPT) + 16)

Best Regards,
J.

#4 lore raw

PATCH 1/1 Add support for the KwikByte KBOC OMAP35xx board

Dear Jean-Christophe,

Quoted 2 lines · Jean-Christophe PLAGNIOL-VILLARD
Quoted 1 line

board/omap3/kboc/kboc.h

Quoted 1 line
board/omap3/kboc/kboc.h +0 -0

please create you own vendor dirent

NACK. We use board/omap3/<board>/<board>.h syntax. So this is fine. Everything else would make it inconsistent.

Best regards

Dirk

#5 lore raw

PATCH 1/1 Add support for the KwikByte KBOC OMAP35xx board

Dear Dirk Behme,

Quoted 7 lines · In message <[email protected]> you wrote:
Quoted 2 lines · Jean-Christophe PLAGNIOL-VILLARD
Quoted 1 line

board/omap3/kboc/kboc.h

Quoted 1 line
board/omap3/kboc/kboc.h +0 -0

please create you own vendor dirent

NACK. We use board/omap3/<board>/<board>.h syntax. So this is fine. Everything else would make it inconsistent.

I'm not sure what you mean by "we" here. The rus is that a vendor directory shall be used when a company supports any significaant number (say, more than 2...3) of boards. So when for example company FOO who already have other boards in board/foo/* releases their first OMAP3 board, it will naturally go into board/foo/

Best regards,

Wolfgang Denk

Signature · 5 lines
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
Peace was the way.
	-- Kirk, "The City on the Edge of Forever", stardate unknown
#6 lore raw

PATCH 1/1 Add support for the KwikByte KBOC OMAP35xx board

Dear Wolfgang,

Quoted 10 lines · Wolfgang Denk

Dear Dirk Behme,

Quoted 5 lines · In message <[email protected]> you wrote:
Quoted 2 lines · Jean-Christophe PLAGNIOL-VILLARD
Quoted 1 line

board/omap3/kboc/kboc.h

Quoted 1 line
board/omap3/kboc/kboc.h +0 -0

please create you own vendor dirent

NACK. We use board/omap3/<board>/<board>.h syntax. So this is fine. Everything else would make it inconsistent.

I'm not sure what you mean by "we" here.

Most probably the maintainers of all existing board/omap3/* and board/davinci/* boards ;)

Quoted 5 lines

The rus is that a vendor
directory shall be used when a company supports any significaant number (say, more than 2...3) of boards. So when for example company FOO who already have other boards in board/foo/* releases their first OMAP3 board, it will naturally go into board/foo/

Yes, ok, fine.

I understood Jean-Christophe that he wants

board/omap3/<vendor>

and this is what I doesn't like. At least not for the first board of a company. If they, later, add some additional (OMAP3) boards, moving then to board/omap3/<vendor>/<board_A>/, board/omap3/<vendor>/<board_B>/ etc would be fine, though. But please don't make the currently used schema inconsistent just for one (the first) board (not knowing if there ever will be an additional one).

Best regards

Dirk

#7 lore raw

PATCH 1/1 Add support for the KwikByte KBOC OMAP35xx board

Dear Dirk Behme,

Quoted 8 lines · In message <[email protected]> you wrote:

I understood Jean-Christophe that he wants

board/omap3/<vendor>

and this is what I doesn't like. At least not for the first board of a company. If they, later, add some additional (OMAP3) boards, moving then to board/omap3/<vendor>/<board_A>/,

Agred - board/omap3/<vendor> is not acceptable, not for the first board, nor for any number of boards. If a vendor directory is used, then ist must go as board/<vendor>

Otherwise we will have the same "<vendor>" directories all over the place for all processors supported by a vendor - and for some active board vendors that can be a _lot_.

Best regards,

Wolfgang Denk

Signature · 6 lines
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
"The first rule of magic is simple. Don't waste your time waving your
hands and hoping when a rock or a club will do."
                                               - McCloctnik the Lucid
#8 lore raw

PATCH 1/1 Add support for the KwikByte KBOC OMAP35xx board

In reply to Dirk Behme
Quoted 9 lines · Dirk Behme

Dear Jean-Christophe,

Quoted 2 lines · Jean-Christophe PLAGNIOL-VILLARD
Quoted 1 line

board/omap3/kboc/kboc.h

Quoted 1 line
board/omap3/kboc/kboc.h +0 -0

please create you own vendor dirent

NACK. We use board/omap3/<board>/<board>.h syntax. So this is fine. Everything else would make it inconsistent.

have more board in omap3 NACK
omap3 is not a vendor it's a TI soc

I've said it multiple time

No new board will be allow to go in omap3 ditto for davinci

Best Regards,
J.

#9 lore raw

PATCH 1/1 Add support for the KwikByte KBOC OMAP35xx board

Dear Jean-Christophe,

Quoted 11 lines · Jean-Christophe PLAGNIOL-VILLARD
Quoted 8 lines · Dirk Behme

Dear Jean-Christophe,

Quoted 2 lines · Jean-Christophe PLAGNIOL-VILLARD
Quoted 1 line

board/omap3/kboc/kboc.h

Quoted 1 line
board/omap3/kboc/kboc.h +0 -0

please create you own vendor dirent

NACK. We use board/omap3/<board>/<board>.h syntax. So this is fine. Everything else would make it inconsistent.

have more board in omap3 NACK
omap3 is not a vendor it's a TI soc

Please feel free to send a patch to change directory layout as you like and then we can discuss about it.

Quoted 3 lines

I've said it multiple time

No new board will be allow to go in omap3 ditto for davinci

Giving such a statement might sound like "no more (TI?) ARM boards will be allowed to be added" which I think doesn't really help.

Best regards

Dirk

#10 lore raw

PATCH 1/1 Add support for the KwikByte KBOC OMAP35xx board

In reply to Jean-Christophe PLAGNIOL-VILLARD

Jean-Christophe PLAGNIOL-VILLARD said the following on 07/12/2009 08:13 AM:

Quoted 6 lines
Quoted 6 lines
Quoted 6 lines

_sread*/\

+ MUX_VAL(CP(D2D_MBUSFLAG),     (IEN  | PTD | DIS | M0)) /*d2d_mbusflag*/\
+ MUX_VAL(CP(D2D_SBUSFLAG),     (IEN  | PTD | DIS | M0)) /*d2d_sbusflag*/\
+ MUX_VAL(CP(SDRC_CKE0),                (IDIS | PTU | EN  | M0)) /*sdrc_cke0*/\
+ MUX_VAL(CP(SDRC_CKE1),                (IDIS | PTU | EN  | M0)) /*sdrc_cke1*/
Quoted 7 lines
Quoted 4 lines

one more reason why the mux needs a big change in mux handling :( I think we will end up with 1/2 a dozen crazy and code repetition for each board... Arrggghhh...

NM: yes, it's really not easy to follow here
do you plan to do it soon?

Been a little tied up recent days with "work load" hoping things to ease down.. will try to send out a mux cleanup rev next weekend..

Regards,
Nishanth Menon

#11 lore raw

PATCH 1/1 Add support for the KwikByte KBOC OMAP35xx board

Quoted 11 lines · Nishanth Menon

Jean-Christophe PLAGNIOL-VILLARD said the following on 07/12/2009 08:13 AM:

Quoted 10 lines
Quoted 10 lines
Quoted 6 lines

_sread*/\

+ MUX_VAL(CP(D2D_MBUSFLAG),     (IEN  | PTD | DIS | M0)) /*d2d_mbusflag*/\
+ MUX_VAL(CP(D2D_SBUSFLAG),     (IEN  | PTD | DIS | M0)) /*d2d_sbusflag*/\
+ MUX_VAL(CP(SDRC_CKE0),                (IDIS | PTU | EN  | M0)) /*sdrc_cke0*/\
+ MUX_VAL(CP(SDRC_CKE1),                (IDIS | PTU | EN  | M0)) /*sdrc_cke1*/

one more reason why the mux needs a big change in mux handling :( I think we will end up with 1/2 a dozen crazy and code repetition for each board... Arrggghhh...

Quoted 5 lines
Quoted 3 lines

NM: yes, it's really not easy to follow here
do you plan to do it soon?

Been a little tied up recent days with "work load" hoping things to ease down.. will try to send out a mux cleanup rev next weekend..

Btw, I like the way we do pin mux in U-Boot at the moment (*). Or
better: I can't imagine a way how to do it even better without introducing other disadvantages. But I will enjoy to have a look to your changes ;) Maybe you can give us already an idea of how you like to change it?

(*) What I like:

Having everything in one file for each board. With this, you can get a complete overview of board's pin mux with looking only in one file. And you can see immediately for each pin what is configured and how.

Best regards

Dirk

#12 lore raw

[U-Boot] OMAP MUX handling improvement (was: Add support for the KwikByte KBOC OMAP35xx board)

Dirk Behme said the following on 07/12/2009 09:31 AM:

Quoted 29 lines
Quoted 16 lines · Nishanth Menon

Jean-Christophe PLAGNIOL-VILLARD said the following on 07/12/2009 08:13 AM:

Quoted 14 lines
Quoted 14 lines
Quoted 10 lines

_sread*/\
+ MUX_VAL(CP(D2D_MBUSFLAG), (IEN | PTD | DIS | M0))
/*d2d_mbusflag*/\
+ MUX_VAL(CP(D2D_SBUSFLAG), (IEN | PTD | DIS | M0))
/*d2d_sbusflag*/\
+ MUX_VAL(CP(SDRC_CKE0), (IDIS | PTU | EN | M0))
/*sdrc_cke0*/\
+ MUX_VAL(CP(SDRC_CKE1), (IDIS | PTU | EN | M0))
/*sdrc_cke1*/

one more reason why the mux needs a big change in mux handling :( I think we will end up with 1/2 a dozen crazy and code repetition for each board... Arrggghhh...

Quoted 5 lines
Quoted 3 lines

NM: yes, it's really not easy to follow here
do you plan to do it soon?

Been a little tied up recent days with "work load" hoping things to ease down.. will try to send out a mux cleanup rev next weekend..

Btw, I like the way we do pin mux in U-Boot at the moment (*). Or
better: I can't imagine a way how to do it even better without introducing other disadvantages. But I will enjoy to have a look to your changes ;) Maybe you can give us already an idea of how you like to change it?

Quoted 5 lines

(*) What I like:

Having everything in one file for each board. With this, you can get a complete overview of board's pin mux with looking only in one file. And you can see immediately for each pin what is configured and how.

Here are few quick things i like and dont like about the mux handling Pros:
* Simple interface - just a #define
Cons:
* Repetition for every single board for common stuff such as Sdrc dat regs etc..
* Boards tend to enable *every* mux even if u-boot uses or not.

Proposal stage 1:
* move common mux out to a mux.h, where board files can use the defaults if they like -> i recollect having send such a patch out some time back.. but I never got the time to follow up on it.

Proposal stage 2:
* kick out mux settings from each board, which does not belong there -> e.g. if the board does not do camera at u-boot level ->move that out to kernel.

This is just my 2 cents..
Regards,
Nishanth Menon

#13 lore raw

[U-Boot] OMAP MUX handling improvement

Quoted 34 lines · Nishanth Menon

Dirk Behme said the following on 07/12/2009 09:31 AM:

Quoted 28 lines
Quoted 16 lines · Nishanth Menon

Jean-Christophe PLAGNIOL-VILLARD said the following on 07/12/2009 08:13 AM:

Quoted 14 lines
Quoted 14 lines
Quoted 10 lines

_sread*/\
+ MUX_VAL(CP(D2D_MBUSFLAG), (IEN | PTD | DIS | M0))
/*d2d_mbusflag*/\
+ MUX_VAL(CP(D2D_SBUSFLAG), (IEN | PTD | DIS | M0))
/*d2d_sbusflag*/\
+ MUX_VAL(CP(SDRC_CKE0), (IDIS | PTU | EN | M0))
/*sdrc_cke0*/\
+ MUX_VAL(CP(SDRC_CKE1), (IDIS | PTU | EN | M0))
/*sdrc_cke1*/

one more reason why the mux needs a big change in mux handling :( I think we will end up with 1/2 a dozen crazy and code repetition for each board... Arrggghhh...

Quoted 5 lines
Quoted 3 lines

NM: yes, it's really not easy to follow here
do you plan to do it soon?

Been a little tied up recent days with "work load" hoping things to ease down.. will try to send out a mux cleanup rev next weekend..

Btw, I like the way we do pin mux in U-Boot at the moment (*). Or
better: I can't imagine a way how to do it even better without introducing other disadvantages. But I will enjoy to have a look to your changes ;) Maybe you can give us already an idea of how you like to change it?

Quoted 5 lines

(*) What I like:

Having everything in one file for each board. With this, you can get a complete overview of board's pin mux with looking only in one file. And you can see immediately for each pin what is configured and how.

Quoted 6 lines

Here are few quick things i like and dont like about the mux handling Pros:
* Simple interface - just a #define
Cons:
* Repetition for every single board for common stuff such as Sdrc dat regs etc..

This isn't a con for me. Having this in each board directory, you know that it is exactly right for this board and that you don't (accidentally) use some other (generic) code from somewhere else that you never checked. And you have it in one, easy maintainable file. You don't have to search for pin mux in x files scattered around in the source tree, with chance that you miss one if you want to check the pin mux for your board.

Quoted 1 line

* Boards tend to enable *every* mux even if u-boot uses or not.

This is a very big pro for me. Again, with this, you can be sure that the pin mux, which you have in one place, is done right for exactly this board. And you don't have to rely on broken kernel pin mux of anything else. With this, you can be sure that your board boots fine without burning something due to wrong pin mux. Even if you don't use all interfaces.

Quoted 3 lines

Proposal stage 1:
* move common mux out to a mux.h, where board files can use the defaults if they like

Con:

Configuration scattered around in several files, see above.

Quoted 7 lines

-> i recollect having send such a patch out some time back.. but I never got the time to follow up on it.

Proposal stage 2:
* kick out mux settings from each board, which does not belong there -> e.g. if the board does not do camera at u-boot level ->move that out to kernel.

Then you first have to fix totally broken kernel pin mux before we can do this ;)

Best regards

Dirk

#14 lore raw

PATCH 1/1 Add support for the KwikByte KBOC OMAP35xx board

In reply to Jean-Christophe PLAGNIOL-VILLARD

Dear Jean-Christophe PLAGNIOL-VILLARD,

Quoted 3 lines · In message <[email protected]> you wrote:
Quoted 2 lines

board/omap3/kboc/kboc.h

Quoted 2 lines
board/omap3/kboc/kboc.h +0 -0

please create you own vendor dirent

This is only needed if the company is expected to release any significant number of boards.

Best regards,

Wolfgang Denk

Signature · 5 lines
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
...though his invention worked superbly -- his theory was a crock  of
sewage from beginning to end.         - Vernor Vinge, "The Peace War"