Skip to contentSkip to conversation

ixgbe: fix for 82599 errata marking UDP checksum errors

PATCH Applied Jeff Kirsher 3 participants 3 messages Jul 24, 2009 – Jul 27, 2009

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 ixgbe: fix for 82599 errata marking UDP checksum errors

From: Don Skidmore <[email protected]>

There is an 82599 errata that UDP frames with a zero checksum are incorrectly marked as checksum invalid by the hardware. This was leading to misleading hw_csum_rx_error counts. This patch adds a test around this counter increase for this condition.

---

 drivers/net/ixgbe/ixgbe_main.c |   17 +++++++++++++++--
 1 files changed, 15 insertions(+), 2 deletions(-)
drivers/net/ixgbe/ixgbe_main.c +15 -2
index 6887759..200454f 100644
@@ -511,8 +511,11 @@ static void ixgbe_receive_skb(struct ixgbe_q_vector *q_vector,
  * @skb: skb currently being received and modified
  **/
 static inline void ixgbe_rx_checksum(struct ixgbe_adapter *adapter,
-                                     u32 status_err, struct sk_buff *skb)
+				     union ixgbe_adv_rx_desc *rx_desc,
+				     struct sk_buff *skb)
 {
+	u32 status_err = le32_to_cpu(rx_desc->wb.upper.status_error);
+
 	skb->ip_summed = CHECKSUM_NONE;
 
 	/* Rx csum disabled */
@@ -530,6 +533,16 @@ static inline void ixgbe_rx_checksum(struct ixgbe_adapter *adapter,
 		return;
 
 	if (status_err & IXGBE_RXDADV_ERR_TCPE) {
+		u16 pkt_info = rx_desc->wb.lower.lo_dword.hs_rss.pkt_info;
+
+		/*
+		 * 82599 errata, UDP frames with a 0 checksum can be marked as
+		 * checksum errors.
+		 */
+		if ((pkt_info & IXGBE_RXDADV_PKTTYPE_UDP) &&
+		    (adapter->hw.mac.type == ixgbe_mac_82599EB))
+			return;
+
 		adapter->hw_csum_rx_error++;
 		return;
 	}
@@ -803,7 +816,7 @@ static bool ixgbe_clean_rx_irq(struct ixgbe_q_vector *q_vector,
 			goto next_desc;
 		}
 
-		ixgbe_rx_checksum(adapter, staterr, skb);
+		ixgbe_rx_checksum(adapter, rx_desc, skb);
 
 		/* probably a little skewed due to removing CRC */
 		total_rx_bytes += skb->len;
maintainer Applied
#1 lore raw

From: Jeff Kirsher <[email protected]>
Date: Thu, 23 Jul 2009 21:00:39 -0700

Quoted 9 lines

From: Don Skidmore <[email protected]>

There is an 82599 errata that UDP frames with a zero checksum are incorrectly marked as checksum invalid by the hardware. This was leading to misleading hw_csum_rx_error counts. This patch adds a test around this counter increase for this condition.

Applied, thanks.

But I wonder. When you compute a checksum, and it's zero,
you have to use the complement as the checksum value. How does that relate to the problem being tackled here?

#2 lore raw
Quoted 10 lines · David Miller

From: Jeff Kirsher <[email protected]>
Date: Thu, 23 Jul 2009 21:00:39 -0700

Quoted 7 lines

From: Don Skidmore <[email protected]>

There is an 82599 errata that UDP frames with a zero checksum are incorrectly marked as checksum invalid by the hardware. This was leading to misleading hw_csum_rx_error counts. This patch adds a test around this counter increase for this condition.

Quoted 8 lines
Quoted 2 lines

Applied, thanks.

But I wonder. When you compute a checksum, and it's zero,
you have to use the complement as the checksum value. How does that relate to the problem being tackled here?

The problem is our hardware has an errata. If the packet data contains no checksum, or no checksum computed, our hardware doesn't recognize it. So when it tries to compute the checksum on Rx, it doesn't just figure out that it needs to use the one's complement. So it's not recognizing the fact the checksum is either not computed, or computes to zero.

The only place we've seen this show up is receiving from pktgen, where no checksum is computed. It is a really stupid HW errata, and is just an annoyance really (our bad checksum counter soars when doing pktgen stress testing).

Cheers,
-PJ Waskiewicz