regulator: Add GPIO enable control to fixed voltage regulator driver

index cdc674f..0888cb7 100644
@@ -20,20 +20,45 @@
 #include <linux/platform_device.h>
 #include <linux/regulator/driver.h>
 #include <linux/regulator/fixed.h>
+#include <linux/gpio.h>
 
 struct fixed_voltage_data {
 	struct regulator_desc desc;
 	struct regulator_dev *dev;
 	int microvolts;
+	int gpio;
+	unsigned enable_high:1;
+	unsigned is_enabled:1;
 };
 
 static int fixed_voltage_is_enabled(struct regulator_dev *dev)
 {
-	return 1;
+	struct fixed_voltage_data *data = rdev_get_drvdata(dev);
+
+	return data->is_enabled;
 }
 
 static int fixed_voltage_enable(struct regulator_dev *dev)
 {
+	struct fixed_voltage_data *data = rdev_get_drvdata(dev);
+
+	if (gpio_is_valid(data->gpio)) {
+		gpio_set_value_cansleep(data->gpio, data->enable_high);
+		data->is_enabled = 1;
+	}
+
+	return 0;
+}
+
+static int fixed_voltage_disable(struct regulator_dev *dev)
+{
+	struct fixed_voltage_data *data = rdev_get_drvdata(dev);
+
+	if (gpio_is_valid(data->gpio)) {
+		gpio_set_value_cansleep(data->gpio, !data->enable_high);
+		data->is_enabled = 0;
+	}
+
 	return 0;
 }
 

@@ -58,6 +83,7 @@ static int fixed_voltage_list_voltage(struct regulator_dev *dev,
 static struct regulator_ops fixed_voltage_ops = {
 	.is_enabled = fixed_voltage_is_enabled,
 	.enable = fixed_voltage_enable,
+	.disable = fixed_voltage_disable,
 	.get_voltage = fixed_voltage_get_voltage,
 	.list_voltage = fixed_voltage_list_voltage,
 };

@@ -85,12 +111,51 @@ static int regulator_fixed_voltage_probe(struct platform_device *pdev)
 	drvdata->desc.n_voltages = 1;
 
 	drvdata->microvolts = config->microvolts;
+	drvdata->gpio = config->gpio;
+
+	if (gpio_is_valid(config->gpio)) {
+		drvdata->enable_high = config->enable_high;
+
+		/* FIXME: Remove this print warning */
+		if (!config->gpio)
+			dev_warn(&pdev->dev,
+				"using GPIO 0 for regulator enable control\n");
+
+		ret = gpio_request(config->gpio, config->supply_name);
+		if (ret) {
+			dev_err(&pdev->dev,
+			   "Could not obtain regulator enable GPIO %d: %d\n",
+							config->gpio, ret);
+			goto err_name;
+		}
+
+		/* set output direction without changing state
+		 * to prevent glitch
+		 */
+		drvdata->is_enabled = config->enabled_at_boot;
+		if (!config->enable_high)
+			drvdata->is_enabled = !drvdata->is_enabled;
+
+		ret = gpio_direction_output(config->gpio, drvdata->is_enabled);
+		if (ret) {
+			dev_err(&pdev->dev,
+			   "Could not configure regulator enable GPIO %d direction: %d\n",
+							config->gpio, ret);
+			goto err_gpio;
+		}
+
+	} else {
+		/* Regulator without GPIO control is considered
+		 * always enabled
+		 */
+		drvdata->is_enabled = 1;
+	}
 
 	drvdata->dev = regulator_register(&drvdata->desc, &pdev->dev,
 					  config->init_data, drvdata);
 	if (IS_ERR(drvdata->dev)) {
 		ret = PTR_ERR(drvdata->dev);
-		goto err_name;
+		goto err_gpio;
 	}
 
 	platform_set_drvdata(pdev, drvdata);

@@ -100,6 +165,9 @@ static int regulator_fixed_voltage_probe(struct platform_device *pdev)
 
 	return 0;
 
+err_gpio:
+	if (gpio_is_valid(config->gpio))
+		gpio_free(config->gpio);
 err_name:
 	kfree(drvdata->desc.name);
 err:

@@ -115,6 +183,9 @@ static int regulator_fixed_voltage_remove(struct platform_device *pdev)
 	kfree(drvdata->desc.name);
 	kfree(drvdata);
 
+	if (gpio_is_valid(drvdata->gpio))
+		gpio_free(drvdata->gpio);
+
 	return 0;
 }
 

index 91b4da3..bd75b18 100644
@@ -16,9 +16,30 @@
 
 struct regulator_init_data;
 
+/**
+ * struct fixed_voltage_config - fixed_voltage_config structure
+ * @supply_name:	Name of the regulator supply
+ * @microvolts:		Output voltage of regulator
+ * @gpio:		GPIO to use for enable control
+ * 			set to -EINVAL if not used
+ * @enable_high:	Polarity of enable GPIO
+ *			1 = Active high, 0 = Active low
+ * @enabled_at_boot:	Whether regulator has been enabled at
+ * 			boot or not. 1 = Yes, 0 = No
+ * 			This is used to keep the regulator at
+ * 			the default state
+ * @init_data:		regulator_init_data
+ *
+ * This structure contains fixed voltage regulator configuration
+ * information that must be passed by platform code to the fixed
+ * voltage regulator driver.
+ */
 struct fixed_voltage_config {
 	const char *supply_name;
 	int microvolts;
+	int gpio;
+	unsigned enable_high:1;
+	unsigned enabled_at_boot:1;
 	struct regulator_init_data *init_data;
 };