tracing: kprobe-based event tracer and x86 instruction decoder

Hi,

Here are the patches of kprobe-based event tracer for x86, version 14, which allows you to probe various kernel events through ftrace interface. The tracer supports per-probe filtering which allows you to set filters on each probe and shows formats of each probe.

This version includes below fixes.
- Define remove_subsystem_dir() always (patch 6/12)
- Modify syscall_tracer because of ftrace_event_call change (patch 6/12)
- Support 'sa' argument for stack address (patch 8/12)
- Use call->data instead of container_of() macro. (patch 8/12)
- Assign new event id for each event. (patch 11/12)

Lai, this version still can not be applied on your patch ('use defined fields to print formats') yet, since I couldn't update your patch on the latest -tip tree.

This patchset also includes x86(-64) instruction decoder which supports non-SSE/FP opcodes and includes x86 opcode map. The decoder is used for finding the instruction boundaries when inserting new kprobes. I think it will be possible to share this opcode map with KVM's decoder.
The decoder is tested when building kernel, the test compares the results of objdump and the decoder right after building vmlinux. You can enable that test by CONFIG_X86_DECODER_SELFTEST=y.

This series can be applied on the latest linux-2.6.31-rc5-tip.

This supports only x86(-32/-64) (but porting it on other arch just needs kprobes/kretprobes and register and stack access APIs).

I also made two tools for this tracer.
- Kprobe stress test script which tests kprobes on all kernel symbols to find symbols which should be blacklisted.
- C expression to kprobes event format converter which helps you to define kprobes events by C source code line number or function name, and local variable name.

Enhancement ideas will be added after merging:
- .init function tracing support.
- Support primitive types(long, ulong, int, uint, etc) for args.

Kprobe-based Event Tracer
=========================

Overview
--------
This tracer is similar to the events tracer which is based on Tracepoint infrastructure. Instead of Tracepoint, this tracer is based on kprobes(kprobe and kretprobe). It probes anywhere where kprobes can probe(this means, all functions body except for __kprobes functions).

Unlike the function tracer, this tracer can probe instructions inside of kernel functions. It allows you to check which instruction has been executed.

Unlike the Tracepoint based events tracer, this tracer can add new probe points on the fly.

Similar to the events tracer, this tracer doesn't need to be activated via current_tracer, instead of that, just set probe points via /sys/kernel/debug/tracing/kprobe_events. And you can set filters on each probe events via /sys/kernel/debug/tracing/events/kprobes/<EVENT>/filter.

Synopsis of kprobe_events
-------------------------
p[:EVENT] SYMBOL[+offs|-offs]|MEMADDR [FETCHARGS] : Set a probe
r[:EVENT] SYMBOL[+0] [FETCHARGS] : Set a return probe

EVENT : Event name. If omitted, the event name is generated
based on SYMBOL+offs or MEMADDR.
SYMBOL[+offs|-offs] : Symbol+offset where the probe is inserted.
MEMADDR : Address where the probe is inserted.

FETCHARGS : Arguments. Each probe can have up to 128 args.
%REG : Fetch register REG
sN : Fetch Nth entry of stack (N >= 0)
sa : Fetch stack address.
@ADDR : Fetch memory at ADDR (ADDR should be in kernel)
@SYM[+|-offs] : Fetch memory at SYM +|- offs (SYM should be a data symbol)
aN : Fetch function argument. (N >= 0)(*)
rv : Fetch return value.(**)
ra : Fetch return address.(**)
+|-offs(FETCHARG) : fetch memory at FETCHARG +|- offs address.(***)

(*) aN may not correct on asmlinkaged functions and at the middle of
function body.
(**) only for return probe.
(***) this is useful for fetching a field of data structures.

Per-Probe Event Filtering
-------------------------
Per-probe event filtering feature allows you to set different filter on each
probe and gives you what arguments will be shown in trace buffer. If an event name is specified right after 'p:' or 'r:' in kprobe_events, the tracer adds an event under tracing/events/kprobes/<EVENT>, at the directory you can see 'id', 'enabled', 'format' and 'filter'.

enabled:
You can enable/disable the probe by writing 1 or 0 on it.

format:
It shows the format of this probe event. It also shows aliases of arguments
which you specified to kprobe_events.

filter:
You can write filtering rules of this event. And you can use both of aliase
names and field names for describing filters.

Event Profiling
---------------
You can check the total number of probe hits and probe miss-hits via
/sys/kernel/debug/tracing/kprobe_profile.
The first column is event name, the second is the number of probe hits,
the third is the number of probe miss-hits.

Usage examples
--------------
To add a probe as a new event, write a new definition to kprobe_events as below.

echo p:myprobe do_sys_open a0 a1 a2 a3 > /sys/kernel/debug/tracing/kprobe_events

This sets a kprobe on the top of do_sys_open() function with recording
1st to 4th arguments as "myprobe" event.

echo r:myretprobe do_sys_open rv ra >> /sys/kernel/debug/tracing/kprobe_events

This sets a kretprobe on the return point of do_sys_open() function with
recording return value and return address as "myretprobe" event.
You can see the format of these events via
/sys/kernel/debug/tracing/events/kprobes/<EVENT>/format.

cat /sys/kernel/debug/tracing/events/kprobes/myprobe/format
name: myprobe
ID: 23
format:

	field:unsigned short common_type;	offset:0;	size:2;
	field:unsigned char common_flags;	offset:2;	size:1;
	field:unsigned char common_preempt_count;	offset:3;	size:1;
	field:int common_pid;	offset:4;	size:4;
	field:int common_tgid;	offset:8;	size:4;

	field: unsigned long ip;	offset:16;tsize:8;
	field: int nargs;	offset:24;tsize:4;
	field: unsigned long arg0;	offset:32;tsize:8;
	field: unsigned long arg1;	offset:40;tsize:8;
	field: unsigned long arg2;	offset:48;tsize:8;
	field: unsigned long arg3;	offset:56;tsize:8;

	alias: a0;	original: arg0;
	alias: a1;	original: arg1;
	alias: a2;	original: arg2;
	alias: a3;	original: arg3;

print fmt: "%lx: 0x%lx 0x%lx 0x%lx 0x%lx", ip, arg0, arg1, arg2, arg3

You can see that the event has 4 arguments and alias expressions
corresponding to it.

echo > /sys/kernel/debug/tracing/kprobe_events

This clears all probe points. and you can see the traced information via
/sys/kernel/debug/tracing/trace.

cat /sys/kernel/debug/tracing/trace
# tracer: nop
#
# TASK-PID CPU# TIMESTAMP FUNCTION
# | | | | |

           <...>-1447  [001] 1038282.286875: do_sys_open+0x0/0xd6: 0x3 0x7fffd1ec4440 0x8000 0x0
           <...>-1447  [001] 1038282.286878: sys_openat+0xc/0xe <- do_sys_open: 0xfffffffffffffffe 0xffffffff81367a3a
           <...>-1447  [001] 1038282.286885: do_sys_open+0x0/0xd6: 0xffffff9c 0x40413c 0x8000 0x1b6
           <...>-1447  [001] 1038282.286915: sys_open+0x1b/0x1d <- do_sys_open: 0x3 0xffffffff81367a3a
           <...>-1447  [001] 1038282.286969: do_sys_open+0x0/0xd6: 0xffffff9c 0x4041c6 0x98800 0x10
           <...>-1447  [001] 1038282.286976: sys_open+0x1b/0x1d <- do_sys_open: 0x3 0xffffffff81367a3a

Each line shows when the kernel hits a probe, and <- SYMBOL means kernel
returns from SYMBOL(e.g. "sys_open+0x1b/0x1d <- do_sys_open" means kernel returns from do_sys_open to sys_open+0x1b).

Thank you,

---

Masami Hiramatsu (12):
tracing: Add kprobes event profiling interface
tracing: Kprobe tracer assigns new event ids for each event
tracing: Generate names for each kprobe event automatically
tracing: Kprobe-tracer supports more than 6 arguments
tracing: add kprobe-based event tracer
tracing: Introduce TRACE_FIELD_ZERO() macro
tracing: ftrace dynamic ftrace_event_call support
x86: add pt_regs register and stack access APIs
kprobes: cleanup fix_riprel() using insn decoder on x86
kprobes: checks probe address is instruction boudary on x86
x86: x86 instruction decoder build-time selftest
x86: instruction decoder API

 Documentation/trace/kprobetrace.txt  |  148 ++++
 arch/x86/Kconfig.debug               |    9 
 arch/x86/Makefile                    |    3 
 arch/x86/include/asm/inat.h          |  188 +++++
 arch/x86/include/asm/inat_types.h    |   29 +
 arch/x86/include/asm/insn.h          |  143 ++++
 arch/x86/include/asm/ptrace.h        |   62 ++
 arch/x86/kernel/kprobes.c            |  197 +++--
 arch/x86/kernel/ptrace.c             |  112 +++
 arch/x86/lib/Makefile                |   13 
 arch/x86/lib/inat.c                  |   78 ++
 arch/x86/lib/insn.c                  |  464 +++++++++++++
 arch/x86/lib/x86-opcode-map.txt      |  719 ++++++++++++++++++++
 arch/x86/tools/Makefile              |   15 
 arch/x86/tools/distill.awk           |   42 +
 arch/x86/tools/gen-insn-attr-x86.awk |  314 +++++++++
 arch/x86/tools/test_get_len.c        |  113 +++
 include/linux/ftrace_event.h         |   14 
 include/linux/syscalls.h             |    4 
 include/trace/ftrace.h               |   19 -
 include/trace/syscall.h              |    8 
 kernel/trace/Kconfig                 |   12 
 kernel/trace/Makefile                |    1 
 kernel/trace/trace.h                 |   23 +
 kernel/trace/trace_event_types.h     |    4 
 kernel/trace/trace_events.c          |  119 ++-
 kernel/trace/trace_export.c          |   39 +
 kernel/trace/trace_kprobe.c          | 1234 ++++++++++++++++++++++++++++++++++
 kernel/trace/trace_syscalls.c        |   16 
 29 files changed, 3949 insertions(+), 193 deletions(-)
 create mode 100644 Documentation/trace/kprobetrace.txt
 create mode 100644 arch/x86/include/asm/inat.h
 create mode 100644 arch/x86/include/asm/inat_types.h
 create mode 100644 arch/x86/include/asm/insn.h
 create mode 100644 arch/x86/lib/inat.c
 create mode 100644 arch/x86/lib/insn.c
 create mode 100644 arch/x86/lib/x86-opcode-map.txt
 create mode 100644 arch/x86/tools/Makefile
 create mode 100644 arch/x86/tools/distill.awk
 create mode 100644 arch/x86/tools/gen-insn-attr-x86.awk
 create mode 100644 arch/x86/tools/test_get_len.c
 create mode 100644 kernel/trace/trace_kprobe.c

Masami Hiramatsu

Software Engineer
Hitachi Computer Products (America), Inc.
Software Solutions Division

e-mail: [email protected]

Add x86 instruction decoder to arch-specific libraries. This decoder can decode x86 instructions used in kernel into prefix, opcode, modrm, sib, displacement and immediates. This can also show the length of instructions.

This version introduces instruction attributes for decoding instructions. The instruction attribute tables are generated from the opcode map file (x86-opcode-map.txt) by the generator script(gen-insn-attr-x86.awk).

Currently, the opcode maps are based on opcode maps in Intel(R) 64 and IA-32 Architectures Software Developers Manual Vol.2: Appendix.A, and consist of below two types of opcode tables.

1-byte/2-bytes/3-bytes opcodes, which has 256 elements, are written as below;

Table: table-name
Referrer: escaped-name
opcode: mnemonic|GrpXXX [operand1[,operand2...]] [(extra1)[,(extra2)...] [| 2nd-mnemonic ...]
(or)
opcode: escape # escaped-name
EndTable

Group opcodes, which has 8 elements, are written as below;

GrpTable: GrpXXX
reg: mnemonic [operand1[,operand2...]] [(extra1)[,(extra2)...] [| 2nd-mnemonic ...] EndTable

These opcode maps include a few SSE and FP opcodes (for setup), because those opcodes are used in the kernel.

---

 arch/x86/include/asm/inat.h          |  188 +++++++++
 arch/x86/include/asm/inat_types.h    |   29 +
 arch/x86/include/asm/insn.h          |  143 +++++++
 arch/x86/lib/Makefile                |   13 +
 arch/x86/lib/inat.c                  |   78 ++++
 arch/x86/lib/insn.c                  |  464 ++++++++++++++++++++++
 arch/x86/lib/x86-opcode-map.txt      |  719 ++++++++++++++++++++++++++++++++++
 arch/x86/tools/gen-insn-attr-x86.awk |  314 +++++++++++++++
 8 files changed, 1948 insertions(+), 0 deletions(-)
 create mode 100644 arch/x86/include/asm/inat.h
 create mode 100644 arch/x86/include/asm/inat_types.h
 create mode 100644 arch/x86/include/asm/insn.h
 create mode 100644 arch/x86/lib/inat.c
 create mode 100644 arch/x86/lib/insn.c
 create mode 100644 arch/x86/lib/x86-opcode-map.txt
 create mode 100644 arch/x86/tools/gen-insn-attr-x86.awk

new file mode 100644
index 0000000..2866fdd
@@ -0,0 +1,188 @@
+#ifndef _ASM_X86_INAT_H
+#define _ASM_X86_INAT_H
+/*
+ * x86 instruction attributes
+ *
+ * Written by Masami Hiramatsu <[email protected]>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
+ *
+ */
+#include <asm/inat_types.h>
+
+/*
+ * Internal bits. Don't use bitmasks directly, because these bits are
+ * unstable. You should use checking functions.
+ */
+
+#define INAT_OPCODE_TABLE_SIZE 256
+#define INAT_GROUP_TABLE_SIZE 8
+
+/* Legacy instruction prefixes */
+#define INAT_PFX_OPNDSZ	1	/* 0x66 */ /* LPFX1 */
+#define INAT_PFX_REPNE	2	/* 0xF2 */ /* LPFX2 */
+#define INAT_PFX_REPE	3	/* 0xF3 */ /* LPFX3 */
+#define INAT_PFX_LOCK	4	/* 0xF0 */
+#define INAT_PFX_CS	5	/* 0x2E */
+#define INAT_PFX_DS	6	/* 0x3E */
+#define INAT_PFX_ES	7	/* 0x26 */
+#define INAT_PFX_FS	8	/* 0x64 */
+#define INAT_PFX_GS	9	/* 0x65 */
+#define INAT_PFX_SS	10	/* 0x36 */
+#define INAT_PFX_ADDRSZ	11	/* 0x67 */
+
+#define INAT_LPREFIX_MAX	3
+
+/* Immediate size */
+#define INAT_IMM_BYTE		1
+#define INAT_IMM_WORD		2
+#define INAT_IMM_DWORD		3
+#define INAT_IMM_QWORD		4
+#define INAT_IMM_PTR		5
+#define INAT_IMM_VWORD32	6
+#define INAT_IMM_VWORD		7
+
+/* Legacy prefix */
+#define INAT_PFX_OFFS	0
+#define INAT_PFX_BITS	4
+#define INAT_PFX_MAX    ((1 << INAT_PFX_BITS) - 1)
+#define INAT_PFX_MASK	(INAT_PFX_MAX << INAT_PFX_OFFS)
+/* Escape opcodes */
+#define INAT_ESC_OFFS	(INAT_PFX_OFFS + INAT_PFX_BITS)
+#define INAT_ESC_BITS	2
+#define INAT_ESC_MAX	((1 << INAT_ESC_BITS) - 1)
+#define INAT_ESC_MASK	(INAT_ESC_MAX << INAT_ESC_OFFS)
+/* Group opcodes (1-16) */
+#define INAT_GRP_OFFS	(INAT_ESC_OFFS + INAT_ESC_BITS)
+#define INAT_GRP_BITS	5
+#define INAT_GRP_MAX	((1 << INAT_GRP_BITS) - 1)
+#define INAT_GRP_MASK	(INAT_GRP_MAX << INAT_GRP_OFFS)
+/* Immediates */
+#define INAT_IMM_OFFS	(INAT_GRP_OFFS + INAT_GRP_BITS)
+#define INAT_IMM_BITS	3
+#define INAT_IMM_MASK	(((1 << INAT_IMM_BITS) - 1) << INAT_IMM_OFFS)
+/* Flags */
+#define INAT_FLAG_OFFS	(INAT_IMM_OFFS + INAT_IMM_BITS)
+#define INAT_REXPFX	(1 << INAT_FLAG_OFFS)
+#define INAT_MODRM	(1 << (INAT_FLAG_OFFS + 1))
+#define INAT_FORCE64	(1 << (INAT_FLAG_OFFS + 2))
+#define INAT_SCNDIMM	(1 << (INAT_FLAG_OFFS + 3))
+#define INAT_MOFFSET	(1 << (INAT_FLAG_OFFS + 4))
+#define INAT_VARIANT	(1 << (INAT_FLAG_OFFS + 5))
+/* Attribute making macros for attribute tables */
+#define INAT_MAKE_PREFIX(pfx)	(pfx << INAT_PFX_OFFS)
+#define INAT_MAKE_ESCAPE(esc)	(esc << INAT_ESC_OFFS)
+#define INAT_MAKE_GROUP(grp)	((grp << INAT_GRP_OFFS) | INAT_MODRM)
+#define INAT_MAKE_IMM(imm)	(imm << INAT_IMM_OFFS)
+
+/* Attribute search APIs */
+extern insn_attr_t inat_get_opcode_attribute(insn_byte_t opcode);
+extern insn_attr_t inat_get_escape_attribute(insn_byte_t opcode,
+					     insn_byte_t last_pfx,
+					     insn_attr_t esc_attr);
+extern insn_attr_t inat_get_group_attribute(insn_byte_t modrm,
+					    insn_byte_t last_pfx,
+					    insn_attr_t esc_attr);
+
+/* Attribute checking functions */
+static inline int inat_is_prefix(insn_attr_t attr)
+{
+	return attr & INAT_PFX_MASK;
+}
+
+static inline int inat_is_address_size_prefix(insn_attr_t attr)
+{
+	return (attr & INAT_PFX_MASK) == INAT_PFX_ADDRSZ;
+}
+
+static inline int inat_is_operand_size_prefix(insn_attr_t attr)
+{
+	return (attr & INAT_PFX_MASK) == INAT_PFX_OPNDSZ;
+}
+
+static inline int inat_last_prefix_id(insn_attr_t attr)
+{
+	if ((attr & INAT_PFX_MASK) > INAT_LPREFIX_MAX)
+		return 0;
+	else
+		return attr & INAT_PFX_MASK;
+}
+
+static inline int inat_is_escape(insn_attr_t attr)
+{
+	return attr & INAT_ESC_MASK;
+}
+
+static inline int inat_escape_id(insn_attr_t attr)
+{
+	return (attr & INAT_ESC_MASK) >> INAT_ESC_OFFS;
+}
+
+static inline int inat_is_group(insn_attr_t attr)
+{
+	return attr & INAT_GRP_MASK;
+}
+
+static inline int inat_group_id(insn_attr_t attr)
+{
+	return (attr & INAT_GRP_MASK) >> INAT_GRP_OFFS;
+}
+
+static inline int inat_group_common_attribute(insn_attr_t attr)
+{
+	return attr & ~INAT_GRP_MASK;
+}
+
+static inline int inat_has_immediate(insn_attr_t attr)
+{
+	return attr & INAT_IMM_MASK;
+}
+
+static inline int inat_immediate_size(insn_attr_t attr)
+{
+	return (attr & INAT_IMM_MASK) >> INAT_IMM_OFFS;
+}
+
+static inline int inat_is_rex_prefix(insn_attr_t attr)
+{
+	return attr & INAT_REXPFX;
+}
+
+static inline int inat_has_modrm(insn_attr_t attr)
+{
+	return attr & INAT_MODRM;
+}
+
+static inline int inat_is_force64(insn_attr_t attr)
+{
+	return attr & INAT_FORCE64;
+}
+
+static inline int inat_has_second_immediate(insn_attr_t attr)
+{
+	return attr & INAT_SCNDIMM;
+}
+
+static inline int inat_has_moffset(insn_attr_t attr)
+{
+	return attr & INAT_MOFFSET;
+}
+
+static inline int inat_has_variant(insn_attr_t attr)
+{
+	return attr & INAT_VARIANT;
+}
+
+#endif

new file mode 100644
index 0000000..cb3c20c
@@ -0,0 +1,29 @@
+#ifndef _ASM_X86_INAT_TYPES_H
+#define _ASM_X86_INAT_TYPES_H
+/*
+ * x86 instruction attributes
+ *
+ * Written by Masami Hiramatsu <[email protected]>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
+ *
+ */
+
+/* Instruction attributes */
+typedef unsigned int insn_attr_t;
+typedef unsigned char insn_byte_t;
+typedef signed int insn_value_t;
+
+#endif

index 07c3189..c77f8a7 100644
@@ -2,12 +2,25 @@
 # Makefile for x86 specific library files.
 #
 
+inat_tables_script = $(srctree)/arch/x86/tools/gen-insn-attr-x86.awk
+inat_tables_maps = $(srctree)/arch/x86/lib/x86-opcode-map.txt
+quiet_cmd_inat_tables = GEN     $@
+      cmd_inat_tables = $(AWK) -f $(inat_tables_script) $(inat_tables_maps) > $@
+
+$(obj)/inat-tables.c: $(inat_tables_script) $(inat_tables_maps)
+	$(call cmd,inat_tables)
+
+$(obj)/inat.o: $(obj)/inat-tables.c
+
+clean-files := inat-tables.c
+
 obj-$(CONFIG_SMP) := msr.o
 
 lib-y := delay.o
 lib-y += thunk_$(BITS).o
 lib-y += usercopy_$(BITS).o getuser.o putuser.o
 lib-y += memcpy_$(BITS).o
+lib-y += insn.o inat.o
 
 ifeq ($(CONFIG_X86_32),y)
         obj-y += atomic64_32.o

Masami Hiramatsu

Software Engineer
Hitachi Computer Products (America), Inc.
Software Solutions Division

e-mail: [email protected]

I'm getting the following build error on an old K7 box:

arch/x86/lib/inat.c: In function ‘inat_get_opcode_attribute’:
arch/x86/lib/inat.c:29: erreur: ‘inat_primary_table’ undeclared (first use in this function) arch/x86/lib/inat.c:29: erreur: (Each undeclared identifier is reported only once arch/x86/lib/inat.c:29: erreur: for each function it appears in.)

I've attached my config. I haven't such problem on a dual x86-64 box.

#
# Automatically generated make config: don't edit # Linux kernel version: 2.6.31-rc5
# Fri Jun 11 05:59:12 2010
#
# CONFIG_64BIT is not set
CONFIG_X86_32=y
# CONFIG_X86_64 is not set
CONFIG_X86=y
CONFIG_OUTPUT_FORMAT="elf32-i386" CONFIG_ARCH_DEFCONFIG="arch/x86/configs/i386_defconfig" CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_CMOS_UPDATE=y CONFIG_CLOCKSOURCE_WATCHDOG=y CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_CLOCKEVENTS_BROADCAST=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_HAVE_LATENCYTOP_SUPPORT=y CONFIG_FAST_CMPXCHG_LOCAL=y
CONFIG_MMU=y
CONFIG_ZONE_DMA=y
CONFIG_GENERIC_ISA_DMA=y
CONFIG_GENERIC_IOMAP=y
CONFIG_GENERIC_BUG=y
CONFIG_GENERIC_HWEIGHT=y CONFIG_ARCH_MAY_HAVE_PC_FDC=y
# CONFIG_RWSEM_GENERIC_SPINLOCK is not set CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_ARCH_HAS_CPU_IDLE_WAIT=y CONFIG_GENERIC_CALIBRATE_DELAY=y
# CONFIG_GENERIC_TIME_VSYSCALL is not set CONFIG_ARCH_HAS_CPU_RELAX=y CONFIG_ARCH_HAS_DEFAULT_IDLE=y CONFIG_ARCH_HAS_CACHE_LINE_SIZE=y CONFIG_HAVE_SETUP_PER_CPU_AREA=y CONFIG_HAVE_DYNAMIC_PER_CPU_AREA=y
# CONFIG_HAVE_CPUMASK_OF_CPU_MAP is not set CONFIG_ARCH_HIBERNATION_POSSIBLE=y CONFIG_ARCH_SUSPEND_POSSIBLE=y
# CONFIG_ZONE_DMA32 is not set CONFIG_ARCH_POPULATES_NODE_MAP=y
# CONFIG_AUDIT_ARCH is not set CONFIG_ARCH_SUPPORTS_OPTIMIZED_INLINING=y CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y CONFIG_GENERIC_HARDIRQS=y CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y CONFIG_GENERIC_IRQ_PROBE=y CONFIG_GENERIC_PENDING_IRQ=y CONFIG_USE_GENERIC_SMP_HELPERS=y CONFIG_X86_32_SMP=y
CONFIG_X86_HT=y
CONFIG_X86_TRAMPOLINE=y
CONFIG_X86_32_LAZY_GS=y
CONFIG_KTIME_SCALAR=y CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" CONFIG_CONSTRUCTORS=y

#
# General setup
#
CONFIG_EXPERIMENTAL=y
CONFIG_LOCK_KERNEL=y
CONFIG_INIT_ENV_ARG_LIMIT=32
CONFIG_LOCALVERSION=""
# CONFIG_LOCALVERSION_AUTO is not set
CONFIG_HAVE_KERNEL_GZIP=y
CONFIG_HAVE_KERNEL_BZIP2=y
CONFIG_HAVE_KERNEL_LZMA=y
CONFIG_KERNEL_GZIP=y
# CONFIG_KERNEL_BZIP2 is not set
# CONFIG_KERNEL_LZMA is not set
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
CONFIG_SYSVIPC_SYSCTL=y
CONFIG_POSIX_MQUEUE=y
CONFIG_POSIX_MQUEUE_SYSCTL=y
CONFIG_BSD_PROCESS_ACCT=y
CONFIG_BSD_PROCESS_ACCT_V3=y
# CONFIG_TASKSTATS is not set
CONFIG_AUDIT=y
# CONFIG_AUDITSYSCALL is not set

#
# RCU Subsystem
#
CONFIG_CLASSIC_RCU=y
# CONFIG_TREE_RCU is not set
# CONFIG_PREEMPT_RCU is not set
# CONFIG_TREE_RCU_TRACE is not set
# CONFIG_PREEMPT_RCU_TRACE is not set
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_LOG_BUF_SHIFT=17
CONFIG_HAVE_UNSTABLE_SCHED_CLOCK=y
# CONFIG_GROUP_SCHED is not set
# CONFIG_CGROUPS is not set
CONFIG_SYSFS_DEPRECATED=y
CONFIG_SYSFS_DEPRECATED_V2=y
CONFIG_RELAY=y
CONFIG_NAMESPACES=y
# CONFIG_UTS_NS is not set
# CONFIG_IPC_NS is not set
# CONFIG_USER_NS is not set
# CONFIG_PID_NS is not set
# CONFIG_NET_NS is not set
CONFIG_BLK_DEV_INITRD=y
CONFIG_INITRAMFS_SOURCE=""
CONFIG_RD_GZIP=y
CONFIG_RD_BZIP2=y
CONFIG_RD_LZMA=y
# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
CONFIG_SYSCTL=y
CONFIG_ANON_INODES=y
# CONFIG_EMBEDDED is not set
CONFIG_UID16=y
CONFIG_SYSCTL_SYSCALL=y
CONFIG_KALLSYMS=y
CONFIG_KALLSYMS_ALL=y
# CONFIG_KALLSYMS_EXTRA_PASS is not set
CONFIG_HOTPLUG=y
CONFIG_PRINTK=y
CONFIG_BUG=y
CONFIG_ELF_CORE=y
CONFIG_PCSPKR_PLATFORM=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
CONFIG_EPOLL=y
CONFIG_SIGNALFD=y
CONFIG_TIMERFD=y
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_AIO=y
CONFIG_HAVE_PERF_COUNTERS=y

#
# Performance Counters
#
CONFIG_PERF_COUNTERS=y
CONFIG_EVENT_PROFILE=y
CONFIG_VM_EVENT_COUNTERS=y
CONFIG_PCI_QUIRKS=y
# CONFIG_STRIP_ASM_SYMS is not set
CONFIG_COMPAT_BRK=y
CONFIG_SLAB=y
# CONFIG_SLUB is not set
# CONFIG_SLOB is not set
CONFIG_PROFILING=y
CONFIG_TRACEPOINTS=y
CONFIG_MARKERS=y
CONFIG_OPROFILE=y
# CONFIG_OPROFILE_IBS is not set
CONFIG_HAVE_OPROFILE=y
CONFIG_KPROBES=y
CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS=y
CONFIG_KRETPROBES=y
CONFIG_HAVE_IOREMAP_PROT=y
CONFIG_HAVE_KPROBES=y
CONFIG_HAVE_KRETPROBES=y
CONFIG_HAVE_ARCH_TRACEHOOK=y
CONFIG_HAVE_DMA_ATTRS=y
CONFIG_HAVE_DMA_API_DEBUG=y

#
# GCOV-based kernel profiling
#
# CONFIG_GCOV_KERNEL is not set
# CONFIG_SLOW_WORK is not set
CONFIG_HAVE_GENERIC_DMA_COHERENT=y
CONFIG_SLABINFO=y
CONFIG_RT_MUTEXES=y
CONFIG_BASE_SMALL=0
CONFIG_MODULES=y
# CONFIG_MODULE_FORCE_LOAD is not set
# CONFIG_MODULE_UNLOAD is not set
# CONFIG_MODVERSIONS is not set
# CONFIG_MODULE_SRCVERSION_ALL is not set
CONFIG_STOP_MACHINE=y
CONFIG_BLOCK=y
CONFIG_LBDAF=y
# CONFIG_BLK_DEV_BSG is not set
# CONFIG_BLK_DEV_INTEGRITY is not set

#
# IO Schedulers
#
CONFIG_IOSCHED_NOOP=y
CONFIG_IOSCHED_AS=y
CONFIG_IOSCHED_DEADLINE=y
CONFIG_IOSCHED_CFQ=y
# CONFIG_DEFAULT_AS is not set
# CONFIG_DEFAULT_DEADLINE is not set
# CONFIG_DEFAULT_CFQ is not set
CONFIG_DEFAULT_NOOP=y
CONFIG_DEFAULT_IOSCHED="noop"
CONFIG_FREEZER=y

#
# Processor type and features
#
CONFIG_TICK_ONESHOT=y
CONFIG_NO_HZ=y
CONFIG_HIGH_RES_TIMERS=y CONFIG_GENERIC_CLOCKEVENTS_BUILD=y CONFIG_SMP=y
# CONFIG_SPARSE_IRQ is not set CONFIG_X86_MPPARSE=y
# CONFIG_X86_BIGSMP is not set
# CONFIG_X86_EXTENDED_PLATFORM is not set CONFIG_SCHED_OMIT_FRAME_POINTER=y
# CONFIG_PARAVIRT_GUEST is not set
# CONFIG_MEMTEST is not set
# CONFIG_M386 is not set
# CONFIG_M486 is not set
# CONFIG_M586 is not set
# CONFIG_M586TSC is not set
# CONFIG_M586MMX is not set
# CONFIG_M686 is not set
# CONFIG_MPENTIUMII is not set
# CONFIG_MPENTIUMIII is not set
# CONFIG_MPENTIUMM is not set
# CONFIG_MPENTIUM4 is not set
# CONFIG_MK6 is not set
CONFIG_MK7=y
# CONFIG_MK8 is not set
# CONFIG_MCRUSOE is not set
# CONFIG_MEFFICEON is not set
# CONFIG_MWINCHIPC6 is not set
# CONFIG_MWINCHIP3D is not set
# CONFIG_MGEODEGX1 is not set
# CONFIG_MGEODE_LX is not set
# CONFIG_MCYRIXIII is not set
# CONFIG_MVIAC3_2 is not set
# CONFIG_MVIAC7 is not set
# CONFIG_MPSC is not set
# CONFIG_MCORE2 is not set
# CONFIG_GENERIC_CPU is not set
# CONFIG_X86_GENERIC is not set CONFIG_X86_CPU=y CONFIG_X86_L1_CACHE_BYTES=64 CONFIG_X86_INTERNODE_CACHE_BYTES=64 CONFIG_X86_CMPXCHG=y CONFIG_X86_L1_CACHE_SHIFT=6 CONFIG_X86_XADD=y
CONFIG_X86_WP_WORKS_OK=y
CONFIG_X86_INVLPG=y
CONFIG_X86_BSWAP=y
CONFIG_X86_POPAD_OK=y CONFIG_X86_INTEL_USERCOPY=y CONFIG_X86_USE_PPRO_CHECKSUM=y CONFIG_X86_USE_3DNOW=y
CONFIG_X86_TSC=y
CONFIG_X86_CMOV=y CONFIG_X86_MINIMUM_CPU_FAMILY=4 CONFIG_X86_DEBUGCTLMSR=y CONFIG_CPU_SUP_INTEL=y CONFIG_CPU_SUP_CYRIX_32=y CONFIG_CPU_SUP_AMD=y CONFIG_CPU_SUP_CENTAUR=y CONFIG_CPU_SUP_TRANSMETA_32=y CONFIG_CPU_SUP_UMC_32=y
# CONFIG_X86_DS is not set CONFIG_HPET_TIMER=y
CONFIG_DMI=y
# CONFIG_IOMMU_HELPER is not set
# CONFIG_IOMMU_API is not set CONFIG_NR_CPUS=2
CONFIG_SCHED_SMT=y
CONFIG_SCHED_MC=y
# CONFIG_PREEMPT_NONE is not set
# CONFIG_PREEMPT_VOLUNTARY is not set CONFIG_PREEMPT=y
CONFIG_X86_LOCAL_APIC=y
CONFIG_X86_IO_APIC=y
# CONFIG_X86_REROUTE_FOR_BROKEN_BOOT_IRQS is not set # CONFIG_X86_MCE is not set
# CONFIG_X86_ANCIENT_MCE is not set CONFIG_VM86=y
# CONFIG_TOSHIBA is not set
# CONFIG_I8K is not set CONFIG_X86_REBOOTFIXUPS=y
CONFIG_MICROCODE=y
CONFIG_MICROCODE_INTEL=y
# CONFIG_MICROCODE_AMD is not set CONFIG_MICROCODE_OLD_INTERFACE=y CONFIG_X86_MSR=y
CONFIG_X86_CPUID=y
# CONFIG_X86_CPU_DEBUG is not set CONFIG_NOHIGHMEM=y
# CONFIG_HIGHMEM4G is not set
# CONFIG_HIGHMEM64G is not set CONFIG_PAGE_OFFSET=0xC0000000
# CONFIG_X86_PAE is not set
# CONFIG_ARCH_PHYS_ADDR_T_64BIT is not set CONFIG_ARCH_FLATMEM_ENABLE=y CONFIG_ARCH_SPARSEMEM_ENABLE=y CONFIG_ARCH_SELECT_MEMORY_MODEL=y CONFIG_SELECT_MEMORY_MODEL=y CONFIG_FLATMEM_MANUAL=y
# CONFIG_DISCONTIGMEM_MANUAL is not set
# CONFIG_SPARSEMEM_MANUAL is not set CONFIG_FLATMEM=y
CONFIG_FLAT_NODE_MEM_MAP=y CONFIG_SPARSEMEM_STATIC=y CONFIG_PAGEFLAGS_EXTENDED=y CONFIG_SPLIT_PTLOCK_CPUS=4
# CONFIG_PHYS_ADDR_T_64BIT is not set CONFIG_ZONE_DMA_FLAG=1
CONFIG_BOUNCE=y
CONFIG_VIRT_TO_BUS=y
CONFIG_HAVE_MLOCK=y CONFIG_HAVE_MLOCKED_PAGE_BIT=y CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
# CONFIG_X86_CHECK_BIOS_CORRUPTION is not set CONFIG_X86_RESERVE_LOW_64K=y
# CONFIG_MATH_EMULATION is not set CONFIG_MTRR=y
CONFIG_MTRR_SANITIZER=y CONFIG_MTRR_SANITIZER_ENABLE_DEFAULT=0 CONFIG_MTRR_SANITIZER_SPARE_REG_NR_DEFAULT=1 # CONFIG_X86_PAT is not set
CONFIG_EFI=y
CONFIG_SECCOMP=y
# CONFIG_CC_STACKPROTECTOR is not set
# CONFIG_HZ_100 is not set
# CONFIG_HZ_250 is not set
# CONFIG_HZ_300 is not set
CONFIG_HZ_1000=y
CONFIG_HZ=1000
CONFIG_SCHED_HRTICK=y
# CONFIG_KEXEC is not set CONFIG_PHYSICAL_START=0x1000000
# CONFIG_RELOCATABLE is not set CONFIG_PHYSICAL_ALIGN=0x100000 CONFIG_HOTPLUG_CPU=y
CONFIG_COMPAT_VDSO=y
CONFIG_CMDLINE_BOOL=y
CONFIG_CMDLINE=""
# CONFIG_CMDLINE_OVERRIDE is not set

#
# Power management and ACPI options
#
CONFIG_PM=y
CONFIG_PM_DEBUG=y
# CONFIG_PM_VERBOSE is not set
CONFIG_CAN_PM_TRACE=y
# CONFIG_PM_TRACE_RTC is not set
CONFIG_PM_SLEEP_SMP=y
CONFIG_PM_SLEEP=y
CONFIG_SUSPEND=y
CONFIG_SUSPEND_FREEZER=y
# CONFIG_HIBERNATION is not set
CONFIG_ACPI=y
CONFIG_ACPI_SLEEP=y
# CONFIG_ACPI_PROCFS is not set
CONFIG_ACPI_PROCFS_POWER=y
CONFIG_ACPI_SYSFS_POWER=y
CONFIG_ACPI_PROC_EVENT=y
CONFIG_ACPI_AC=y
CONFIG_ACPI_BATTERY=y
CONFIG_ACPI_BUTTON=y
CONFIG_ACPI_FAN=y
# CONFIG_ACPI_DOCK is not set
CONFIG_ACPI_PROCESSOR=y
CONFIG_ACPI_HOTPLUG_CPU=y
CONFIG_ACPI_THERMAL=y
# CONFIG_ACPI_CUSTOM_DSDT is not set
CONFIG_ACPI_BLACKLIST_YEAR=2000
# CONFIG_ACPI_DEBUG is not set
# CONFIG_ACPI_PCI_SLOT is not set
CONFIG_X86_PM_TIMER=y
CONFIG_ACPI_CONTAINER=y
CONFIG_ACPI_SBS=y
CONFIG_X86_APM_BOOT=y
CONFIG_APM=y
# CONFIG_APM_IGNORE_USER_SUSPEND is not set
# CONFIG_APM_DO_ENABLE is not set
# CONFIG_APM_CPU_IDLE is not set
# CONFIG_APM_DISPLAY_BLANK is not set
# CONFIG_APM_ALLOW_INTS is not set

#
# CPU Frequency scaling
#
# CONFIG_CPU_FREQ is not set
CONFIG_CPU_IDLE=y
CONFIG_CPU_IDLE_GOV_LADDER=y
CONFIG_CPU_IDLE_GOV_MENU=y

#
# Bus options (PCI etc.)
#
CONFIG_PCI=y
# CONFIG_PCI_GOBIOS is not set
# CONFIG_PCI_GOMMCONFIG is not set
# CONFIG_PCI_GODIRECT is not set
# CONFIG_PCI_GOOLPC is not set
CONFIG_PCI_GOANY=y
CONFIG_PCI_BIOS=y
CONFIG_PCI_DIRECT=y
CONFIG_PCI_MMCONFIG=y
CONFIG_PCI_DOMAINS=y
CONFIG_PCIEPORTBUS=y
# CONFIG_HOTPLUG_PCI_PCIE is not set
CONFIG_PCIEAER=y
# CONFIG_PCIE_ECRC is not set
# CONFIG_PCIEAER_INJECT is not set
# CONFIG_PCIEASPM is not set
CONFIG_ARCH_SUPPORTS_MSI=y
# CONFIG_PCI_MSI is not set
CONFIG_PCI_LEGACY=y
# CONFIG_PCI_DEBUG is not set
CONFIG_PCI_STUB=y
CONFIG_HT_IRQ=y
# CONFIG_PCI_IOV is not set
CONFIG_ISA_DMA_API=y
# CONFIG_ISA is not set
# CONFIG_MCA is not set
# CONFIG_SCx200 is not set
# CONFIG_OLPC is not set
# CONFIG_PCCARD is not set
CONFIG_HOTPLUG_PCI=y
# CONFIG_HOTPLUG_PCI_FAKE is not set
# CONFIG_HOTPLUG_PCI_COMPAQ is not set
# CONFIG_HOTPLUG_PCI_IBM is not set
CONFIG_HOTPLUG_PCI_ACPI=y
# CONFIG_HOTPLUG_PCI_ACPI_IBM is not set
# CONFIG_HOTPLUG_PCI_CPCI is not set
CONFIG_HOTPLUG_PCI_SHPC=y

#
# Executable file formats / Emulations
#
CONFIG_BINFMT_ELF=y
# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
CONFIG_HAVE_AOUT=y
CONFIG_BINFMT_AOUT=y
CONFIG_BINFMT_MISC=y
CONFIG_HAVE_ATOMIC_IOMAP=y
CONFIG_NET=y

#
# Networking options
#
CONFIG_PACKET=y
CONFIG_PACKET_MMAP=y
CONFIG_UNIX=y
CONFIG_XFRM=y
CONFIG_XFRM_USER=y
# CONFIG_XFRM_SUB_POLICY is not set
# CONFIG_XFRM_MIGRATE is not set
# CONFIG_XFRM_STATISTICS is not set
CONFIG_XFRM_IPCOMP=y
CONFIG_NET_KEY=y
# CONFIG_NET_KEY_MIGRATE is not set
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
# CONFIG_IP_ADVANCED_ROUTER is not set
CONFIG_IP_FIB_HASH=y
# CONFIG_IP_PNP is not set
CONFIG_NET_IPIP=y
CONFIG_NET_IPGRE=y
CONFIG_NET_IPGRE_BROADCAST=y
# CONFIG_IP_MROUTE is not set
# CONFIG_ARPD is not set
CONFIG_SYN_COOKIES=y
CONFIG_INET_AH=y
CONFIG_INET_ESP=y
CONFIG_INET_IPCOMP=y
CONFIG_INET_XFRM_TUNNEL=y
CONFIG_INET_TUNNEL=y
CONFIG_INET_XFRM_MODE_TRANSPORT=y
CONFIG_INET_XFRM_MODE_TUNNEL=y
CONFIG_INET_XFRM_MODE_BEET=y
# CONFIG_INET_LRO is not set
CONFIG_INET_DIAG=y
CONFIG_INET_TCP_DIAG=y
# CONFIG_TCP_CONG_ADVANCED is not set
CONFIG_TCP_CONG_CUBIC=y
CONFIG_DEFAULT_TCP_CONG="cubic"
CONFIG_TCP_MD5SIG=y
# CONFIG_IPV6 is not set
# CONFIG_NETLABEL is not set
CONFIG_NETWORK_SECMARK=y
# CONFIG_NETFILTER is not set
# CONFIG_IP_DCCP is not set
CONFIG_IP_SCTP=y
# CONFIG_SCTP_DBG_MSG is not set
# CONFIG_SCTP_DBG_OBJCNT is not set
# CONFIG_SCTP_HMAC_NONE is not set
# CONFIG_SCTP_HMAC_SHA1 is not set
CONFIG_SCTP_HMAC_MD5=y
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_NET_DSA is not set
# CONFIG_VLAN_8021Q is not set
# CONFIG_DECNET is not set
# CONFIG_LLC2 is not set
# CONFIG_IPX is not set
# CONFIG_ATALK is not set
# CONFIG_X25 is not set
# CONFIG_LAPB is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
# CONFIG_PHONET is not set
# CONFIG_IEEE802154 is not set
# CONFIG_NET_SCHED is not set
# CONFIG_DCB is not set

#
# Network testing
#
# CONFIG_NET_PKTGEN is not set
# CONFIG_NET_TCPPROBE is not set
# CONFIG_NET_DROP_MONITOR is not set
# CONFIG_HAMRADIO is not set
# CONFIG_CAN is not set
# CONFIG_IRDA is not set
# CONFIG_BT is not set
# CONFIG_AF_RXRPC is not set
# CONFIG_WIRELESS is not set
# CONFIG_WIMAX is not set
CONFIG_RFKILL=y
CONFIG_RFKILL_INPUT=y
# CONFIG_NET_9P is not set

#
# Device Drivers
#

#
# Generic Driver Options
#
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=y
CONFIG_FIRMWARE_IN_KERNEL=y
CONFIG_EXTRA_FIRMWARE=""
# CONFIG_DEBUG_DRIVER is not set
# CONFIG_DEBUG_DEVRES is not set
# CONFIG_SYS_HYPERVISOR is not set
# CONFIG_CONNECTOR is not set
# CONFIG_MTD is not set
# CONFIG_PARPORT is not set
CONFIG_PNP=y
CONFIG_PNP_DEBUG_MESSAGES=y

#
# Protocols
#
CONFIG_PNPACPI=y
CONFIG_BLK_DEV=y
# CONFIG_BLK_DEV_FD is not set
# CONFIG_BLK_CPQ_DA is not set
# CONFIG_BLK_CPQ_CISS_DA is not set
# CONFIG_BLK_DEV_DAC960 is not set
# CONFIG_BLK_DEV_UMEM is not set
# CONFIG_BLK_DEV_COW_COMMON is not set
CONFIG_BLK_DEV_LOOP=y
CONFIG_BLK_DEV_CRYPTOLOOP=y
CONFIG_BLK_DEV_NBD=y
# CONFIG_BLK_DEV_SX8 is not set
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_COUNT=16
CONFIG_BLK_DEV_RAM_SIZE=65536
# CONFIG_BLK_DEV_XIP is not set
# CONFIG_CDROM_PKTCDVD is not set
# CONFIG_ATA_OVER_ETH is not set
# CONFIG_BLK_DEV_HD is not set
# CONFIG_MISC_DEVICES is not set
CONFIG_HAVE_IDE=y
CONFIG_IDE=y

#
# Please see Documentation/ide/ide.txt for help/info on IDE drives #
CONFIG_IDE_XFER_MODE=y
CONFIG_IDE_TIMINGS=y
# CONFIG_BLK_DEV_IDE_SATA is not set
CONFIG_IDE_GD=y
CONFIG_IDE_GD_ATA=y
# CONFIG_IDE_GD_ATAPI is not set
# CONFIG_BLK_DEV_IDECD is not set
# CONFIG_BLK_DEV_IDETAPE is not set CONFIG_BLK_DEV_IDEACPI=y
# CONFIG_IDE_TASK_IOCTL is not set
CONFIG_IDE_PROC_FS=y

#
# IDE chipset support/bugfixes
#
# CONFIG_IDE_GENERIC is not set
# CONFIG_BLK_DEV_PLATFORM is not set
# CONFIG_BLK_DEV_CMD640 is not set
CONFIG_BLK_DEV_IDEPNP=y
CONFIG_BLK_DEV_IDEDMA_SFF=y

#
# PCI IDE chipsets support
#
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_IDEPCI_PCIBUS_ORDER=y
# CONFIG_BLK_DEV_GENERIC is not set
# CONFIG_BLK_DEV_OPTI621 is not set
# CONFIG_BLK_DEV_RZ1000 is not set
CONFIG_BLK_DEV_IDEDMA_PCI=y
# CONFIG_BLK_DEV_AEC62XX is not set
# CONFIG_BLK_DEV_ALI15X3 is not set
# CONFIG_BLK_DEV_AMD74XX is not set
# CONFIG_BLK_DEV_ATIIXP is not set
# CONFIG_BLK_DEV_CMD64X is not set
# CONFIG_BLK_DEV_TRIFLEX is not set
# CONFIG_BLK_DEV_CS5520 is not set
# CONFIG_BLK_DEV_CS5530 is not set
# CONFIG_BLK_DEV_CS5535 is not set
# CONFIG_BLK_DEV_CS5536 is not set
# CONFIG_BLK_DEV_HPT366 is not set
# CONFIG_BLK_DEV_JMICRON is not set
# CONFIG_BLK_DEV_SC1200 is not set
# CONFIG_BLK_DEV_PIIX is not set
# CONFIG_BLK_DEV_IT8172 is not set
# CONFIG_BLK_DEV_IT8213 is not set
# CONFIG_BLK_DEV_IT821X is not set
# CONFIG_BLK_DEV_NS87415 is not set
# CONFIG_BLK_DEV_PDC202XX_OLD is not set
# CONFIG_BLK_DEV_PDC202XX_NEW is not set
# CONFIG_BLK_DEV_SVWKS is not set
# CONFIG_BLK_DEV_SIIMAGE is not set
# CONFIG_BLK_DEV_SIS5513 is not set
# CONFIG_BLK_DEV_SLC90E66 is not set
# CONFIG_BLK_DEV_TRM290 is not set
CONFIG_BLK_DEV_VIA82CXXX=y
# CONFIG_BLK_DEV_TC86C001 is not set
CONFIG_BLK_DEV_IDEDMA=y

#
# SCSI device support
#
# CONFIG_RAID_ATTRS is not set
CONFIG_SCSI=y
CONFIG_SCSI_DMA=y
CONFIG_SCSI_TGT=y
CONFIG_SCSI_NETLINK=y
CONFIG_SCSI_PROC_FS=y

#
# SCSI support type (disk, tape, CD-ROM)
#
CONFIG_BLK_DEV_SD=y
# CONFIG_CHR_DEV_ST is not set
# CONFIG_CHR_DEV_OSST is not set
# CONFIG_BLK_DEV_SR is not set
CONFIG_CHR_DEV_SG=y
# CONFIG_CHR_DEV_SCH is not set
# CONFIG_SCSI_MULTI_LUN is not set
# CONFIG_SCSI_CONSTANTS is not set
# CONFIG_SCSI_LOGGING is not set
# CONFIG_SCSI_SCAN_ASYNC is not set
CONFIG_SCSI_WAIT_SCAN=m

#
# SCSI Transports
#
CONFIG_SCSI_SPI_ATTRS=y
CONFIG_SCSI_FC_ATTRS=y
# CONFIG_SCSI_FC_TGT_ATTRS is not set
CONFIG_SCSI_ISCSI_ATTRS=y
CONFIG_SCSI_SAS_ATTRS=y
CONFIG_SCSI_SAS_LIBSAS=y
CONFIG_SCSI_SAS_HOST_SMP=y
# CONFIG_SCSI_SAS_LIBSAS_DEBUG is not set
# CONFIG_SCSI_SRP_ATTRS is not set
# CONFIG_SCSI_LOWLEVEL is not set
# CONFIG_SCSI_DH is not set
# CONFIG_SCSI_OSD_INITIATOR is not set
# CONFIG_ATA is not set
# CONFIG_MD is not set
# CONFIG_FUSION is not set

#
# IEEE 1394 (FireWire) support
#

#
# You can enable one or both FireWire driver stacks. #

#
# See the help texts for more information. #
# CONFIG_FIREWIRE is not set
# CONFIG_IEEE1394 is not set
# CONFIG_I2O is not set
# CONFIG_MACINTOSH_DRIVERS is not set CONFIG_NETDEVICES=y
CONFIG_DUMMY=y
CONFIG_BONDING=y
# CONFIG_MACVLAN is not set
# CONFIG_EQUALIZER is not set
# CONFIG_TUN is not set
# CONFIG_VETH is not set
# CONFIG_NET_SB1000 is not set
# CONFIG_ARCNET is not set
# CONFIG_PHYLIB is not set CONFIG_NET_ETHERNET=y
CONFIG_MII=y
# CONFIG_HAPPYMEAL is not set
# CONFIG_SUNGEM is not set
# CONFIG_CASSINI is not set
# CONFIG_NET_VENDOR_3COM is not set
# CONFIG_ETHOC is not set
# CONFIG_DNET is not set CONFIG_NET_TULIP=y
# CONFIG_DE2104X is not set
CONFIG_TULIP=y
CONFIG_TULIP_MWI=y
CONFIG_TULIP_MMIO=y
# CONFIG_TULIP_NAPI is not set
# CONFIG_DE4X5 is not set
# CONFIG_WINBOND_840 is not set
# CONFIG_DM9102 is not set
# CONFIG_ULI526X is not set
# CONFIG_HP100 is not set
# CONFIG_IBM_NEW_EMAC_ZMII is not set
# CONFIG_IBM_NEW_EMAC_RGMII is not set
# CONFIG_IBM_NEW_EMAC_TAH is not set
# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
# CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set # CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_NET_PCI is not set
# CONFIG_B44 is not set
# CONFIG_KS8842 is not set
# CONFIG_ATL2 is not set
# CONFIG_NETDEV_1000 is not set
# CONFIG_NETDEV_10000 is not set
# CONFIG_TR is not set

#
# Wireless LAN
#
# CONFIG_WLAN_PRE80211 is not set
# CONFIG_WLAN_80211 is not set

#
# Enable WiMAX (Networking options) to see the WiMAX drivers #
# CONFIG_WAN is not set
# CONFIG_FDDI is not set
# CONFIG_HIPPI is not set
# CONFIG_PPP is not set
# CONFIG_SLIP is not set
# CONFIG_NET_FC is not set
# CONFIG_NETCONSOLE is not set
# CONFIG_NETPOLL is not set
# CONFIG_NET_POLL_CONTROLLER is not set
# CONFIG_ISDN is not set
# CONFIG_PHONE is not set

#
# Input device support
#
CONFIG_INPUT=y
CONFIG_INPUT_FF_MEMLESS=y
CONFIG_INPUT_POLLDEV=y

#
# Userland interfaces
#
CONFIG_INPUT_MOUSEDEV=y
# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
# CONFIG_INPUT_JOYDEV is not set
CONFIG_INPUT_EVDEV=y
# CONFIG_INPUT_EVBUG is not set

#
# Input Device Drivers
#
CONFIG_INPUT_KEYBOARD=y
CONFIG_KEYBOARD_ATKBD=y
CONFIG_KEYBOARD_LKKBD=y
# CONFIG_KEYBOARD_LM8323 is not set
CONFIG_KEYBOARD_NEWTON=y
CONFIG_KEYBOARD_STOWAWAY=y
CONFIG_KEYBOARD_SUNKBD=y
CONFIG_KEYBOARD_XTKBD=y
# CONFIG_INPUT_MOUSE is not set
# CONFIG_INPUT_JOYSTICK is not set
# CONFIG_INPUT_TABLET is not set
# CONFIG_INPUT_TOUCHSCREEN is not set
CONFIG_INPUT_MISC=y
CONFIG_INPUT_PCSPKR=y
# CONFIG_INPUT_APANEL is not set
CONFIG_INPUT_WISTRON_BTNS=y
# CONFIG_INPUT_ATLAS_BTNS is not set
CONFIG_INPUT_UINPUT=y

#
# Hardware I/O ports
#
CONFIG_SERIO=y
CONFIG_SERIO_I8042=y
CONFIG_SERIO_SERPORT=y
CONFIG_SERIO_CT82C710=y
CONFIG_SERIO_PCIPS2=y
CONFIG_SERIO_LIBPS2=y
CONFIG_SERIO_RAW=y
CONFIG_GAMEPORT=y
CONFIG_GAMEPORT_NS558=y
CONFIG_GAMEPORT_L4=y
CONFIG_GAMEPORT_EMU10K1=y
CONFIG_GAMEPORT_FM801=y

#
# Character devices
#
CONFIG_VT=y
CONFIG_CONSOLE_TRANSLATIONS=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
CONFIG_VT_HW_CONSOLE_BINDING=y
CONFIG_DEVKMEM=y
CONFIG_SERIAL_NONSTANDARD=y
# CONFIG_COMPUTONE is not set
# CONFIG_ROCKETPORT is not set
# CONFIG_CYCLADES is not set
# CONFIG_DIGIEPCA is not set
# CONFIG_MOXA_INTELLIO is not set
# CONFIG_MOXA_SMARTIO is not set
# CONFIG_ISI is not set
# CONFIG_SYNCLINK is not set
# CONFIG_SYNCLINKMP is not set
# CONFIG_SYNCLINK_GT is not set
# CONFIG_N_HDLC is not set
# CONFIG_RISCOM8 is not set
# CONFIG_SPECIALIX is not set
# CONFIG_SX is not set
# CONFIG_RIO is not set
# CONFIG_STALDRV is not set
# CONFIG_NOZOMI is not set

#
# Serial drivers
#
# CONFIG_SERIAL_8250 is not set
CONFIG_FIX_EARLYCON_MEM=y

#
# Non-8250 serial port support
#
# CONFIG_SERIAL_JSM is not set
CONFIG_UNIX98_PTYS=y
# CONFIG_DEVPTS_MULTIPLE_INSTANCES is not set
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=256
# CONFIG_IPMI_HANDLER is not set
# CONFIG_HW_RANDOM is not set
CONFIG_NVRAM=y
# CONFIG_RTC is not set
# CONFIG_GEN_RTC is not set
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set
# CONFIG_SONYPI is not set
# CONFIG_MWAVE is not set
# CONFIG_PC8736x_GPIO is not set
# CONFIG_NSC_GPIO is not set
# CONFIG_CS5535_GPIO is not set
# CONFIG_RAW_DRIVER is not set
CONFIG_HPET=y
CONFIG_HPET_MMAP=y
# CONFIG_HANGCHECK_TIMER is not set
# CONFIG_TCG_TPM is not set
# CONFIG_TELCLOCK is not set
CONFIG_DEVPORT=y
CONFIG_I2C=y
CONFIG_I2C_BOARDINFO=y
# CONFIG_I2C_CHARDEV is not set
# CONFIG_I2C_HELPER_AUTO is not set

#
# I2C Algorithms
#
CONFIG_I2C_ALGOBIT=y
# CONFIG_I2C_ALGOPCF is not set
# CONFIG_I2C_ALGOPCA is not set

#
# I2C Hardware Bus support
#

#
# PC SMBus host controller drivers
#
# CONFIG_I2C_ALI1535 is not set
# CONFIG_I2C_ALI1563 is not set
# CONFIG_I2C_ALI15X3 is not set
# CONFIG_I2C_AMD756 is not set
# CONFIG_I2C_AMD8111 is not set
# CONFIG_I2C_I801 is not set
# CONFIG_I2C_ISCH is not set
# CONFIG_I2C_PIIX4 is not set
# CONFIG_I2C_NFORCE2 is not set
# CONFIG_I2C_SIS5595 is not set
# CONFIG_I2C_SIS630 is not set
# CONFIG_I2C_SIS96X is not set
CONFIG_I2C_VIA=y
CONFIG_I2C_VIAPRO=y

#
# I2C system bus drivers (mostly embedded / system-on-chip) #
# CONFIG_I2C_OCORES is not set
# CONFIG_I2C_SIMTEC is not set

#
# External I2C/SMBus adapter drivers
#
# CONFIG_I2C_PARPORT_LIGHT is not set
# CONFIG_I2C_TAOS_EVM is not set

#
# Graphics adapter I2C/DDC channel drivers
#
# CONFIG_I2C_VOODOO3 is not set

#
# Other I2C/SMBus bus drivers
#
# CONFIG_I2C_PCA_PLATFORM is not set
# CONFIG_I2C_STUB is not set
# CONFIG_SCx200_ACB is not set

#
# Miscellaneous I2C Chip support
#
# CONFIG_DS1682 is not set
# CONFIG_SENSORS_PCF8574 is not set
# CONFIG_PCF8575 is not set
# CONFIG_SENSORS_PCA9539 is not set
# CONFIG_SENSORS_TSL2550 is not set
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
# CONFIG_I2C_DEBUG_BUS is not set
# CONFIG_I2C_DEBUG_CHIP is not set
# CONFIG_SPI is not set

#
# PPS support
#
# CONFIG_PPS is not set
CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
# CONFIG_GPIOLIB is not set
# CONFIG_W1 is not set
CONFIG_POWER_SUPPLY=y
# CONFIG_POWER_SUPPLY_DEBUG is not set
# CONFIG_PDA_POWER is not set
# CONFIG_BATTERY_DS2760 is not set
# CONFIG_BATTERY_DS2782 is not set
# CONFIG_BATTERY_BQ27x00 is not set
# CONFIG_BATTERY_MAX17040 is not set
# CONFIG_HWMON is not set
CONFIG_THERMAL=y
# CONFIG_WATCHDOG is not set
CONFIG_SSB_POSSIBLE=y

#
# Sonics Silicon Backplane
#
# CONFIG_SSB is not set

#
# Multifunction device drivers
#
# CONFIG_MFD_CORE is not set
# CONFIG_MFD_SM501 is not set
# CONFIG_HTC_PASIC3 is not set
# CONFIG_TWL4030_CORE is not set
# CONFIG_MFD_TMIO is not set
# CONFIG_PMIC_DA903X is not set
# CONFIG_MFD_WM8400 is not set
# CONFIG_MFD_WM8350_I2C is not set
# CONFIG_MFD_PCF50633 is not set
# CONFIG_AB3100_CORE is not set
# CONFIG_REGULATOR is not set
# CONFIG_MEDIA_SUPPORT is not set

#
# Graphics support
#
CONFIG_AGP=y
# CONFIG_AGP_ALI is not set
# CONFIG_AGP_ATI is not set
# CONFIG_AGP_AMD is not set
# CONFIG_AGP_AMD64 is not set
# CONFIG_AGP_INTEL is not set
CONFIG_AGP_NVIDIA=y
# CONFIG_AGP_SIS is not set
# CONFIG_AGP_SWORKS is not set
CONFIG_AGP_VIA=y
# CONFIG_AGP_EFFICEON is not set
CONFIG_DRM=y
CONFIG_DRM_TDFX=y
CONFIG_DRM_R128=y
CONFIG_DRM_RADEON=y
CONFIG_DRM_MGA=y
CONFIG_DRM_SIS=y
CONFIG_DRM_VIA=y
CONFIG_DRM_SAVAGE=y
CONFIG_VGASTATE=y
# CONFIG_VIDEO_OUTPUT_CONTROL is not set
CONFIG_FB=y
CONFIG_FIRMWARE_EDID=y
CONFIG_FB_DDC=y
CONFIG_FB_BOOT_VESA_SUPPORT=y
CONFIG_FB_CFB_FILLRECT=y
CONFIG_FB_CFB_COPYAREA=y
CONFIG_FB_CFB_IMAGEBLIT=y
# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set
# CONFIG_FB_SYS_FILLRECT is not set
# CONFIG_FB_SYS_COPYAREA is not set
# CONFIG_FB_SYS_IMAGEBLIT is not set
# CONFIG_FB_FOREIGN_ENDIAN is not set
# CONFIG_FB_SYS_FOPS is not set
# CONFIG_FB_SVGALIB is not set
# CONFIG_FB_MACMODES is not set
CONFIG_FB_BACKLIGHT=y
CONFIG_FB_MODE_HELPERS=y
CONFIG_FB_TILEBLITTING=y

#
# Frame buffer hardware drivers
#
# CONFIG_FB_CIRRUS is not set
# CONFIG_FB_PM2 is not set
# CONFIG_FB_CYBER2000 is not set
# CONFIG_FB_ARC is not set
# CONFIG_FB_ASILIANT is not set
# CONFIG_FB_IMSTT is not set
CONFIG_FB_VGA16=y
CONFIG_FB_VESA=y
# CONFIG_FB_EFI is not set
# CONFIG_FB_N411 is not set
# CONFIG_FB_HGA is not set
# CONFIG_FB_S1D13XXX is not set
CONFIG_FB_NVIDIA=y
CONFIG_FB_NVIDIA_I2C=y
# CONFIG_FB_NVIDIA_DEBUG is not set
CONFIG_FB_NVIDIA_BACKLIGHT=y
# CONFIG_FB_RIVA is not set
# CONFIG_FB_LE80578 is not set
# CONFIG_FB_MATROX is not set
# CONFIG_FB_RADEON is not set
# CONFIG_FB_ATY128 is not set
# CONFIG_FB_ATY is not set
# CONFIG_FB_S3 is not set
# CONFIG_FB_SAVAGE is not set
# CONFIG_FB_SIS is not set
# CONFIG_FB_VIA is not set
# CONFIG_FB_NEOMAGIC is not set
# CONFIG_FB_KYRO is not set
# CONFIG_FB_3DFX is not set
# CONFIG_FB_VOODOO1 is not set
# CONFIG_FB_VT8623 is not set
# CONFIG_FB_TRIDENT is not set
# CONFIG_FB_ARK is not set
# CONFIG_FB_PM3 is not set
# CONFIG_FB_CARMINE is not set
# CONFIG_FB_GEODE is not set
# CONFIG_FB_VIRTUAL is not set
# CONFIG_FB_METRONOME is not set
# CONFIG_FB_MB862XX is not set
# CONFIG_FB_BROADSHEET is not set
CONFIG_BACKLIGHT_LCD_SUPPORT=y
# CONFIG_LCD_CLASS_DEVICE is not set
CONFIG_BACKLIGHT_CLASS_DEVICE=y
# CONFIG_BACKLIGHT_GENERIC is not set
# CONFIG_BACKLIGHT_PROGEAR is not set
# CONFIG_BACKLIGHT_MBP_NVIDIA is not set
# CONFIG_BACKLIGHT_SAHARA is not set

#
# Display device support
#
CONFIG_DISPLAY_SUPPORT=y

#
# Display hardware drivers
#

#
# Console display driver support
#
CONFIG_VGA_CONSOLE=y
CONFIG_VGACON_SOFT_SCROLLBACK=y
CONFIG_VGACON_SOFT_SCROLLBACK_SIZE=64
CONFIG_DUMMY_CONSOLE=y
CONFIG_FRAMEBUFFER_CONSOLE=y
CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY=y
CONFIG_FRAMEBUFFER_CONSOLE_ROTATION=y
CONFIG_FONTS=y
# CONFIG_FONT_8x8 is not set
CONFIG_FONT_8x16=y
# CONFIG_FONT_6x11 is not set
# CONFIG_FONT_7x14 is not set
# CONFIG_FONT_PEARL_8x8 is not set
# CONFIG_FONT_ACORN_8x8 is not set
# CONFIG_FONT_MINI_4x6 is not set
# CONFIG_FONT_SUN8x16 is not set
# CONFIG_FONT_SUN12x22 is not set
# CONFIG_FONT_10x18 is not set
CONFIG_LOGO=y
# CONFIG_LOGO_LINUX_MONO is not set
# CONFIG_LOGO_LINUX_VGA16 is not set
CONFIG_LOGO_LINUX_CLUT224=y
# CONFIG_SOUND is not set
# CONFIG_HID_SUPPORT is not set
# CONFIG_USB_SUPPORT is not set
# CONFIG_UWB is not set
# CONFIG_MMC is not set
# CONFIG_MEMSTICK is not set
CONFIG_NEW_LEDS=y
CONFIG_LEDS_CLASS=y

#
# LED drivers
#
# CONFIG_LEDS_ALIX2 is not set
# CONFIG_LEDS_PCA9532 is not set
# CONFIG_LEDS_LP3944 is not set
# CONFIG_LEDS_CLEVO_MAIL is not set
# CONFIG_LEDS_PCA955X is not set
# CONFIG_LEDS_BD2802 is not set

#
# LED Triggers
#
# CONFIG_LEDS_TRIGGERS is not set
# CONFIG_ACCESSIBILITY is not set
# CONFIG_INFINIBAND is not set
# CONFIG_EDAC is not set
# CONFIG_RTC_CLASS is not set
# CONFIG_DMADEVICES is not set
# CONFIG_AUXDISPLAY is not set
# CONFIG_UIO is not set

#
# TI VLYNQ
#
# CONFIG_STAGING is not set
# CONFIG_X86_PLATFORM_DEVICES is not set

#
# Firmware Drivers
#
# CONFIG_EDD is not set
CONFIG_FIRMWARE_MEMMAP=y
CONFIG_EFI_VARS=y
CONFIG_DELL_RBU=y
# CONFIG_DCDBAS is not set
CONFIG_DMIID=y
# CONFIG_ISCSI_IBFT_FIND is not set

#
# File systems
#
# CONFIG_EXT2_FS is not set
CONFIG_EXT3_FS=y
# CONFIG_EXT3_DEFAULTS_TO_ORDERED is not set
CONFIG_EXT3_FS_XATTR=y
CONFIG_EXT3_FS_POSIX_ACL=y
CONFIG_EXT3_FS_SECURITY=y
# CONFIG_EXT4_FS is not set
CONFIG_JBD=y
# CONFIG_JBD_DEBUG is not set
CONFIG_FS_MBCACHE=y
CONFIG_REISERFS_FS=y
CONFIG_REISERFS_CHECK=y
# CONFIG_REISERFS_PROC_INFO is not set
CONFIG_REISERFS_FS_XATTR=y
CONFIG_REISERFS_FS_POSIX_ACL=y
CONFIG_REISERFS_FS_SECURITY=y
# CONFIG_JFS_FS is not set
CONFIG_FS_POSIX_ACL=y
# CONFIG_XFS_FS is not set
# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
# CONFIG_BTRFS_FS is not set
CONFIG_FILE_LOCKING=y
CONFIG_FSNOTIFY=y
CONFIG_DNOTIFY=y
CONFIG_INOTIFY=y
CONFIG_INOTIFY_USER=y
# CONFIG_QUOTA is not set
CONFIG_AUTOFS_FS=y
CONFIG_AUTOFS4_FS=y
CONFIG_FUSE_FS=y
# CONFIG_CUSE is not set

#
# Caches
#
# CONFIG_FSCACHE is not set

#
# CD-ROM/DVD Filesystems
#
# CONFIG_ISO9660_FS is not set
# CONFIG_UDF_FS is not set

#
# DOS/FAT/NT Filesystems
#
# CONFIG_MSDOS_FS is not set
# CONFIG_VFAT_FS is not set
# CONFIG_NTFS_FS is not set

#
# Pseudo filesystems
#
CONFIG_PROC_FS=y
CONFIG_PROC_KCORE=y
CONFIG_PROC_SYSCTL=y
CONFIG_PROC_PAGE_MONITOR=y
CONFIG_SYSFS=y
CONFIG_TMPFS=y
# CONFIG_TMPFS_POSIX_ACL is not set
# CONFIG_HUGETLBFS is not set
# CONFIG_HUGETLB_PAGE is not set
CONFIG_CONFIGFS_FS=y
CONFIG_MISC_FILESYSTEMS=y
# CONFIG_ADFS_FS is not set
# CONFIG_AFFS_FS is not set
# CONFIG_ECRYPT_FS is not set
# CONFIG_HFS_FS is not set
# CONFIG_HFSPLUS_FS is not set
# CONFIG_BEFS_FS is not set
# CONFIG_BFS_FS is not set
# CONFIG_EFS_FS is not set
CONFIG_CRAMFS=y
# CONFIG_SQUASHFS is not set
# CONFIG_VXFS_FS is not set
# CONFIG_MINIX_FS is not set
# CONFIG_OMFS_FS is not set
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
CONFIG_ROMFS_FS=y
CONFIG_ROMFS_BACKED_BY_BLOCK=y
# CONFIG_ROMFS_BACKED_BY_MTD is not set
# CONFIG_ROMFS_BACKED_BY_BOTH is not set
CONFIG_ROMFS_ON_BLOCK=y
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
# CONFIG_NILFS2_FS is not set
CONFIG_NETWORK_FILESYSTEMS=y
CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
# CONFIG_NFS_V3_ACL is not set
CONFIG_NFS_V4=y
# CONFIG_NFS_V4_1 is not set
# CONFIG_NFSD is not set
CONFIG_LOCKD=y
CONFIG_LOCKD_V4=y
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=y
CONFIG_SUNRPC_GSS=y
CONFIG_RPCSEC_GSS_KRB5=y
CONFIG_RPCSEC_GSS_SPKM3=y
# CONFIG_SMB_FS is not set
# CONFIG_CIFS is not set
# CONFIG_NCP_FS is not set
# CONFIG_CODA_FS is not set
# CONFIG_AFS_FS is not set

#
# Partition Types
#
CONFIG_PARTITION_ADVANCED=y
# CONFIG_ACORN_PARTITION is not set
# CONFIG_OSF_PARTITION is not set
# CONFIG_AMIGA_PARTITION is not set
# CONFIG_ATARI_PARTITION is not set
# CONFIG_MAC_PARTITION is not set
CONFIG_MSDOS_PARTITION=y
# CONFIG_BSD_DISKLABEL is not set
# CONFIG_MINIX_SUBPARTITION is not set
# CONFIG_SOLARIS_X86_PARTITION is not set
# CONFIG_UNIXWARE_DISKLABEL is not set
CONFIG_LDM_PARTITION=y
# CONFIG_LDM_DEBUG is not set
CONFIG_SGI_PARTITION=y
# CONFIG_ULTRIX_PARTITION is not set
# CONFIG_SUN_PARTITION is not set
# CONFIG_KARMA_PARTITION is not set
CONFIG_EFI_PARTITION=y
# CONFIG_SYSV68_PARTITION is not set
CONFIG_NLS=y
CONFIG_NLS_DEFAULT="cp437"
CONFIG_NLS_CODEPAGE_437=y
# CONFIG_NLS_CODEPAGE_737 is not set
# CONFIG_NLS_CODEPAGE_775 is not set
CONFIG_NLS_CODEPAGE_850=y
# CONFIG_NLS_CODEPAGE_852 is not set
# CONFIG_NLS_CODEPAGE_855 is not set
# CONFIG_NLS_CODEPAGE_857 is not set
# CONFIG_NLS_CODEPAGE_860 is not set
# CONFIG_NLS_CODEPAGE_861 is not set
# CONFIG_NLS_CODEPAGE_862 is not set
# CONFIG_NLS_CODEPAGE_863 is not set
# CONFIG_NLS_CODEPAGE_864 is not set
# CONFIG_NLS_CODEPAGE_865 is not set
# CONFIG_NLS_CODEPAGE_866 is not set
# CONFIG_NLS_CODEPAGE_869 is not set
# CONFIG_NLS_CODEPAGE_936 is not set
# CONFIG_NLS_CODEPAGE_950 is not set
# CONFIG_NLS_CODEPAGE_932 is not set
# CONFIG_NLS_CODEPAGE_949 is not set
# CONFIG_NLS_CODEPAGE_874 is not set
# CONFIG_NLS_ISO8859_8 is not set
CONFIG_NLS_CODEPAGE_1250=y
# CONFIG_NLS_CODEPAGE_1251 is not set
CONFIG_NLS_ASCII=y
CONFIG_NLS_ISO8859_1=y
# CONFIG_NLS_ISO8859_2 is not set
# CONFIG_NLS_ISO8859_3 is not set
# CONFIG_NLS_ISO8859_4 is not set
# CONFIG_NLS_ISO8859_5 is not set
# CONFIG_NLS_ISO8859_6 is not set
# CONFIG_NLS_ISO8859_7 is not set
# CONFIG_NLS_ISO8859_9 is not set
# CONFIG_NLS_ISO8859_13 is not set
# CONFIG_NLS_ISO8859_14 is not set
# CONFIG_NLS_ISO8859_15 is not set
# CONFIG_NLS_KOI8_R is not set
# CONFIG_NLS_KOI8_U is not set
CONFIG_NLS_UTF8=y
# CONFIG_DLM is not set

#
# Kernel hacking
#
CONFIG_TRACE_IRQFLAGS_SUPPORT=y
CONFIG_PRINTK_TIME=y
CONFIG_ENABLE_WARN_DEPRECATED=y
# CONFIG_ENABLE_MUST_CHECK is not set
CONFIG_FRAME_WARN=2048
CONFIG_MAGIC_SYSRQ=y
# CONFIG_UNUSED_SYMBOLS is not set
CONFIG_DEBUG_FS=y
# CONFIG_HEADERS_CHECK is not set
CONFIG_DEBUG_KERNEL=y
# CONFIG_DEBUG_SHIRQ is not set
CONFIG_DETECT_SOFTLOCKUP=y
# CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set
CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0
CONFIG_DETECT_HUNG_TASK=y
# CONFIG_BOOTPARAM_HUNG_TASK_PANIC is not set
CONFIG_BOOTPARAM_HUNG_TASK_PANIC_VALUE=0
CONFIG_SCHED_DEBUG=y
# CONFIG_SCHEDSTATS is not set
# CONFIG_TIMER_STATS is not set
# CONFIG_DEBUG_OBJECTS is not set
# CONFIG_DEBUG_SLAB is not set
# CONFIG_DEBUG_KMEMLEAK is not set
CONFIG_DEBUG_PREEMPT=y
# CONFIG_DEBUG_RT_MUTEXES is not set
# CONFIG_RT_MUTEX_TESTER is not set
CONFIG_DEBUG_SPINLOCK=y
CONFIG_DEBUG_MUTEXES=y
CONFIG_DEBUG_LOCK_ALLOC=y
CONFIG_PROVE_LOCKING=y
CONFIG_LOCKDEP=y
# CONFIG_LOCK_STAT is not set
# CONFIG_DEBUG_LOCKDEP is not set
CONFIG_TRACE_IRQFLAGS=y
CONFIG_DEBUG_SPINLOCK_SLEEP=y
# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
CONFIG_STACKTRACE=y
# CONFIG_DEBUG_KOBJECT is not set
CONFIG_DEBUG_BUGVERBOSE=y
CONFIG_DEBUG_INFO=y
# CONFIG_DEBUG_VM is not set
# CONFIG_DEBUG_VIRTUAL is not set
# CONFIG_DEBUG_WRITECOUNT is not set
CONFIG_DEBUG_MEMORY_INIT=y
# CONFIG_DEBUG_LIST is not set
# CONFIG_DEBUG_SG is not set
# CONFIG_DEBUG_NOTIFIERS is not set
CONFIG_ARCH_WANT_FRAME_POINTERS=y
CONFIG_FRAME_POINTER=y
# CONFIG_BOOT_PRINTK_DELAY is not set
# CONFIG_RCU_TORTURE_TEST is not set
CONFIG_RCU_CPU_STALL_DETECTOR=y
CONFIG_KPROBES_SANITY_TEST=y
# CONFIG_BACKTRACE_SELF_TEST is not set
# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set
# CONFIG_LKDTM is not set
# CONFIG_FAULT_INJECTION is not set
# CONFIG_LATENCYTOP is not set
# CONFIG_SYSCTL_SYSCALL_CHECK is not set
# CONFIG_DEBUG_PAGEALLOC is not set
CONFIG_USER_STACKTRACE_SUPPORT=y
CONFIG_NOP_TRACER=y
CONFIG_HAVE_FTRACE_NMI_ENTER=y
CONFIG_HAVE_FUNCTION_TRACER=y
CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
CONFIG_HAVE_FUNCTION_GRAPH_FP_TEST=y
CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST=y
CONFIG_HAVE_DYNAMIC_FTRACE=y
CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
CONFIG_HAVE_FTRACE_SYSCALLS=y
CONFIG_RING_BUFFER=y
CONFIG_FTRACE_NMI_ENTER=y
CONFIG_EVENT_TRACING=y
CONFIG_CONTEXT_SWITCH_TRACER=y
CONFIG_TRACING=y
CONFIG_GENERIC_TRACER=y
CONFIG_TRACING_SUPPORT=y
CONFIG_FTRACE=y
CONFIG_FUNCTION_TRACER=y
CONFIG_FUNCTION_GRAPH_TRACER=y
# CONFIG_IRQSOFF_TRACER is not set
# CONFIG_PREEMPT_TRACER is not set
# CONFIG_SYSPROF_TRACER is not set
# CONFIG_SCHED_TRACER is not set
# CONFIG_FTRACE_SYSCALLS is not set
# CONFIG_BOOT_TRACER is not set
CONFIG_BRANCH_PROFILE_NONE=y
# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set
# CONFIG_PROFILE_ALL_BRANCHES is not set
# CONFIG_POWER_TRACER is not set
# CONFIG_STACK_TRACER is not set
# CONFIG_KMEMTRACE is not set
# CONFIG_WORKQUEUE_TRACER is not set
# CONFIG_BLK_DEV_IO_TRACE is not set
CONFIG_KPROBE_TRACER=y
CONFIG_DYNAMIC_FTRACE=y
# CONFIG_FUNCTION_PROFILER is not set
CONFIG_FTRACE_MCOUNT_RECORD=y
CONFIG_FTRACE_SELFTEST=y
CONFIG_FTRACE_STARTUP_TEST=y
# CONFIG_MMIOTRACE is not set
# CONFIG_RING_BUFFER_BENCHMARK is not set
# CONFIG_PROVIDE_OHCI1394_DMA_INIT is not set
# CONFIG_DYNAMIC_DEBUG is not set
# CONFIG_DMA_API_DEBUG is not set
# CONFIG_SAMPLES is not set
CONFIG_HAVE_ARCH_KGDB=y
# CONFIG_KGDB is not set
CONFIG_HAVE_ARCH_KMEMCHECK=y
# CONFIG_STRICT_DEVMEM is not set
# CONFIG_X86_VERBOSE_BOOTUP is not set
CONFIG_EARLY_PRINTK=y
# CONFIG_EARLY_PRINTK_DBGP is not set
# CONFIG_DEBUG_STACKOVERFLOW is not set
# CONFIG_DEBUG_STACK_USAGE is not set
# CONFIG_DEBUG_PER_CPU_MAPS is not set
# CONFIG_X86_PTDUMP is not set
CONFIG_DEBUG_RODATA=y
CONFIG_DEBUG_RODATA_TEST=y
# CONFIG_DEBUG_NX_TEST is not set
# CONFIG_4KSTACKS is not set
CONFIG_DOUBLEFAULT=y
# CONFIG_IOMMU_STRESS is not set
CONFIG_HAVE_MMIOTRACE_SUPPORT=y
CONFIG_X86_DECODER_SELFTEST=y
CONFIG_IO_DELAY_TYPE_0X80=0
CONFIG_IO_DELAY_TYPE_0XED=1
CONFIG_IO_DELAY_TYPE_UDELAY=2
CONFIG_IO_DELAY_TYPE_NONE=3
CONFIG_IO_DELAY_0X80=y
# CONFIG_IO_DELAY_0XED is not set
# CONFIG_IO_DELAY_UDELAY is not set
# CONFIG_IO_DELAY_NONE is not set
CONFIG_DEFAULT_IO_DELAY_TYPE=0
# CONFIG_DEBUG_BOOT_PARAMS is not set
# CONFIG_CPA_DEBUG is not set
# CONFIG_OPTIMIZE_INLINING is not set

#
# Security options
#
CONFIG_KEYS=y
# CONFIG_KEYS_DEBUG_PROC_KEYS is not set CONFIG_SECURITY=y
CONFIG_SECURITYFS=y
CONFIG_SECURITY_NETWORK=y
# CONFIG_SECURITY_NETWORK_XFRM is not set
# CONFIG_SECURITY_PATH is not set
# CONFIG_SECURITY_FILE_CAPABILITIES is not set CONFIG_SECURITY_SELINUX=y CONFIG_SECURITY_SELINUX_BOOTPARAM=y CONFIG_SECURITY_SELINUX_BOOTPARAM_VALUE=0 CONFIG_SECURITY_SELINUX_DISABLE=y CONFIG_SECURITY_SELINUX_DEVELOP=y CONFIG_SECURITY_SELINUX_AVC_STATS=y CONFIG_SECURITY_SELINUX_CHECKREQPROT_VALUE=1
# CONFIG_SECURITY_SELINUX_POLICYDB_VERSION_MAX is not set # CONFIG_SECURITY_TOMOYO is not set
# CONFIG_IMA is not set
CONFIG_CRYPTO=y

#
# Crypto core or helper
#
# CONFIG_CRYPTO_FIPS is not set
CONFIG_CRYPTO_ALGAPI=y
CONFIG_CRYPTO_ALGAPI2=y
CONFIG_CRYPTO_AEAD=y
CONFIG_CRYPTO_AEAD2=y
CONFIG_CRYPTO_BLKCIPHER=y
CONFIG_CRYPTO_BLKCIPHER2=y
CONFIG_CRYPTO_HASH=y
CONFIG_CRYPTO_HASH2=y
CONFIG_CRYPTO_RNG2=y
CONFIG_CRYPTO_PCOMP=y
CONFIG_CRYPTO_MANAGER=y
CONFIG_CRYPTO_MANAGER2=y
CONFIG_CRYPTO_GF128MUL=y
CONFIG_CRYPTO_NULL=y
CONFIG_CRYPTO_WORKQUEUE=y
# CONFIG_CRYPTO_CRYPTD is not set
CONFIG_CRYPTO_AUTHENC=y
# CONFIG_CRYPTO_TEST is not set

#
# Authenticated Encryption with Associated Data
#
# CONFIG_CRYPTO_CCM is not set
# CONFIG_CRYPTO_GCM is not set
# CONFIG_CRYPTO_SEQIV is not set

#
# Block modes
#
CONFIG_CRYPTO_CBC=y
# CONFIG_CRYPTO_CTR is not set
# CONFIG_CRYPTO_CTS is not set
CONFIG_CRYPTO_ECB=y
CONFIG_CRYPTO_LRW=y
# CONFIG_CRYPTO_PCBC is not set
# CONFIG_CRYPTO_XTS is not set

#
# Hash modes
#
CONFIG_CRYPTO_HMAC=y
CONFIG_CRYPTO_XCBC=y

#
# Digest
#
CONFIG_CRYPTO_CRC32C=y
# CONFIG_CRYPTO_CRC32C_INTEL is not set
CONFIG_CRYPTO_MD4=y
CONFIG_CRYPTO_MD5=y
CONFIG_CRYPTO_MICHAEL_MIC=y
# CONFIG_CRYPTO_RMD128 is not set
# CONFIG_CRYPTO_RMD160 is not set
# CONFIG_CRYPTO_RMD256 is not set
# CONFIG_CRYPTO_RMD320 is not set
CONFIG_CRYPTO_SHA1=y
CONFIG_CRYPTO_SHA256=y
CONFIG_CRYPTO_SHA512=y
CONFIG_CRYPTO_TGR192=y
CONFIG_CRYPTO_WP512=y

#
# Ciphers
#
CONFIG_CRYPTO_AES=y
CONFIG_CRYPTO_AES_586=y
CONFIG_CRYPTO_ANUBIS=y
CONFIG_CRYPTO_ARC4=y
CONFIG_CRYPTO_BLOWFISH=y
# CONFIG_CRYPTO_CAMELLIA is not set
CONFIG_CRYPTO_CAST5=y
CONFIG_CRYPTO_CAST6=y
CONFIG_CRYPTO_DES=y
# CONFIG_CRYPTO_FCRYPT is not set
CONFIG_CRYPTO_KHAZAD=y
# CONFIG_CRYPTO_SALSA20 is not set
# CONFIG_CRYPTO_SALSA20_586 is not set
# CONFIG_CRYPTO_SEED is not set
CONFIG_CRYPTO_SERPENT=y
CONFIG_CRYPTO_TEA=y
CONFIG_CRYPTO_TWOFISH=y
CONFIG_CRYPTO_TWOFISH_COMMON=y
CONFIG_CRYPTO_TWOFISH_586=y

#
# Compression
#
CONFIG_CRYPTO_DEFLATE=y
# CONFIG_CRYPTO_ZLIB is not set
# CONFIG_CRYPTO_LZO is not set

#
# Random Number Generation
#
# CONFIG_CRYPTO_ANSI_CPRNG is not set
CONFIG_CRYPTO_HW=y
CONFIG_CRYPTO_DEV_PADLOCK=y
CONFIG_CRYPTO_DEV_PADLOCK_AES=y
CONFIG_CRYPTO_DEV_PADLOCK_SHA=y
CONFIG_CRYPTO_DEV_GEODE=y
# CONFIG_CRYPTO_DEV_HIFN_795X is not set
CONFIG_HAVE_KVM=y
CONFIG_HAVE_KVM_IRQCHIP=y
# CONFIG_VIRTUALIZATION is not set
CONFIG_BINARY_PRINTF=y

#
# Library routines
#
CONFIG_BITREVERSE=y
CONFIG_GENERIC_FIND_FIRST_BIT=y
CONFIG_GENERIC_FIND_NEXT_BIT=y
CONFIG_GENERIC_FIND_LAST_BIT=y
CONFIG_CRC_CCITT=y
CONFIG_CRC16=y
# CONFIG_CRC_T10DIF is not set
CONFIG_CRC_ITU_T=y
CONFIG_CRC32=y
# CONFIG_CRC7 is not set
CONFIG_LIBCRC32C=y
CONFIG_AUDIT_GENERIC=y
CONFIG_ZLIB_INFLATE=y
CONFIG_ZLIB_DEFLATE=y
CONFIG_DECOMPRESS_GZIP=y
CONFIG_DECOMPRESS_BZIP2=y
CONFIG_DECOMPRESS_LZMA=y
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
CONFIG_CHECK_SIGNATURE=y
CONFIG_NLATTR=y

Actually I have the same problem in x86-64
The content of my arch/x86/lib/inat-tables.c:

/* x86 opcode map generated from x86-opcode-map.txt */
/* Do not change this code. */
/* Table: one byte opcode */
/* Escape opcode map array */
const insn_attr_t const *inat_escape_tables[INAT_ESC_MAX + 1][INAT_LPREFIX_MAX + 1] = { };

/* Group opcode map array */
const insn_attr_t const *inat_group_tables[INAT_GRP_MAX + 1][INAT_LPREFIX_MAX + 1] = { };

I guess there is a problem with the generation of this file.

Aah, you may use mawk on Ubuntu 9.04, right? If so, unfortunately, mawk is still under development.

http://invisible-island.net/mawk/CHANGES

        ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^

Look, this means we can't use char-class expressions like [:lower:] until this version...

And I've found another bug in mawk-1.3.3-20090728(the latest one). it almost works, but;

$ mawk 'BEGIN {printf("0x%x\n", 0)}'
0x1
$ gawk 'BEGIN {printf("0x%x\n", 0)}'
0x0

This bug skips an array element index 0x0 in inat-tables.c :(

So, I recommend you to install gawk instead mawk until that supports all posix-awk features, since I don't think it is good idea to avoid all those bugs which depends on implementation (not specification).

Thank you,

Masami Hiramatsu

Software Engineer
Hitachi Computer Products (America), Inc.
Software Solutions Division

e-mail: [email protected]

Aargh...

Ouch, indeed.

Yeah, indeed. May be add a warning (or build error) in case the user uses mawk?

Anyway that works fine now with gawk, thanks!
All your patches build well :-)

Hmm, it is possible that mawk will fix those bugs and catch up soon, so, I think checking mawk is not a good idea.
(and since there will be other awk implementations, it's not fair.)

I think what all I can do now is reporting bugs to mawk and ubuntu people.:-)

Thank you for testing!

Masami Hiramatsu

Software Engineer
Hitachi Computer Products (America), Inc.
Software Solutions Division

e-mail: [email protected]

Yeah, but without your tip I couldn't be able to find the origin before some time.
And the kernel couldn't build anyway.

At least we should do something with this version of mawk.

Hm, indeed.
Maybe, we can run additional sanity check script before using awk, like this;

---
res=echo a | $AWK '/[[:lower:]]+/{print "OK"}'
[ "$res" != "OK" ] && exit 1

res=$AWK 'BEGIN {printf("%x", 0)}'
[ "$res" != "0" ] && exit 1

exit 0
---

Thanks,

Masami Hiramatsu

Software Engineer
Hitachi Computer Products (America), Inc.
Software Solutions Division

e-mail: [email protected]

Yeah, that looks good.

Thanks.

Thanks for reporting!
Hmm, it seems that inat-tables.c is not correctly generated. Could you tell me which awk you used and send the inat-tables.c?

Thank you,

Masami Hiramatsu

Software Engineer
Hitachi Computer Products (America), Inc.
Software Solutions Division

e-mail: [email protected]

Sure:

$ awk -Wv
mawk 1.3.3 Nov 1996, Copyright (C) Michael D. Brennan

compiled limits:
max NF 32767
sprintf buffer 2040

And I've sent you the content of inat_tables.c in the other answer :)

Add a user-space selftest of x86 instruction decoder at kernel build time. When CONFIG_X86_DECODER_SELFTEST=y, Kbuild builds a test harness of x86 instruction decoder and performs it after building vmlinux. The test compares the results of objdump and x86 instruction decoder code and check there are no differences.

---

 arch/x86/Kconfig.debug        |    9 +++
 arch/x86/Makefile             |    3 +
 arch/x86/tools/Makefile       |   15 +++++
 arch/x86/tools/distill.awk    |   42 +++++++++++++++
 arch/x86/tools/test_get_len.c |  113 +++++++++++++++++++++++++++++++++++++++++
 5 files changed, 182 insertions(+), 0 deletions(-)
 create mode 100644 arch/x86/tools/Makefile
 create mode 100644 arch/x86/tools/distill.awk
 create mode 100644 arch/x86/tools/test_get_len.c

index d105f29..7d0b681 100644
@@ -186,6 +186,15 @@ config X86_DS_SELFTEST
 config HAVE_MMIOTRACE_SUPPORT
 	def_bool y
 
+config X86_DECODER_SELFTEST
+     bool "x86 instruction decoder selftest"
+     depends on DEBUG_KERNEL
+	---help---
+	 Perform x86 instruction decoder selftests at build time.
+	 This option is useful for checking the sanity of x86 instruction
+	 decoder code.
+	 If unsure, say "N".
+
 #
 # IO delay types:
 #

index 1f3851a..f79580c 100644
@@ -154,6 +154,9 @@ all: bzImage
 KBUILD_IMAGE := $(boot)/bzImage
 
 bzImage: vmlinux
+ifeq ($(CONFIG_X86_DECODER_SELFTEST),y)
+	$(Q)$(MAKE) $(build)=arch/x86/tools posttest
+endif
 	$(Q)$(MAKE) $(build)=$(boot) $(KBUILD_IMAGE)
 	$(Q)mkdir -p $(objtree)/arch/$(UTS_MACHINE)/boot
 	$(Q)ln -fsn ../../x86/boot/bzImage $(objtree)/arch/$(UTS_MACHINE)/boot/$@

new file mode 100644
index 0000000..3dd626b
@@ -0,0 +1,15 @@
+PHONY += posttest
+quiet_cmd_posttest = TEST    $@
+      cmd_posttest = $(OBJDUMP) -d $(objtree)/vmlinux | awk -f $(srctree)/arch/x86/tools/distill.awk | $(obj)/test_get_len
+
+posttest: $(obj)/test_get_len vmlinux
+	$(call cmd,posttest)
+
+hostprogs-y	:= test_get_len
+
+# -I needed for generated C source and C source which in the kernel tree.
+HOSTCFLAGS_test_get_len.o := -Wall -I$(objtree)/arch/x86/lib/ -I$(srctree)/arch/x86/include/ -I$(srctree)/arch/x86/lib/
+
+# Dependancies are also needed.
+$(obj)/test_get_len.o: $(srctree)/arch/x86/lib/insn.c $(srctree)/arch/x86/lib/inat.c $(srctree)/arch/x86/include/asm/inat_types.h $(srctree)/arch/x86/include/asm/inat.h $(srctree)/arch/x86/include/asm/insn.h $(objtree)/arch/x86/lib/inat-tables.c
+

Masami Hiramatsu

Software Engineer
Hitachi Computer Products (America), Inc.
Software Solutions Division

e-mail: [email protected]

Ensure safeness of inserting kprobes by checking whether the specified address is at the first byte of a instruction on x86.
This is done by decoding probed function from its head to the probe point.

---

 arch/x86/kernel/kprobes.c |   69 +++++++++++++++++++++++++++++++++++++++++++++
 1 files changed, 69 insertions(+), 0 deletions(-)

index b5b1848..80d493f 100644
@@ -48,6 +48,7 @@
 #include <linux/preempt.h>
 #include <linux/module.h>
 #include <linux/kdebug.h>
+#include <linux/kallsyms.h>
 
 #include <asm/cacheflush.h>
 #include <asm/desc.h>

@@ -55,6 +56,7 @@
 #include <asm/uaccess.h>
 #include <asm/alternative.h>
 #include <asm/debugreg.h>
+#include <asm/insn.h>
 
 void jprobe_return_end(void);
 

@@ -245,6 +247,71 @@ retry:
 	}
 }
 
+/* Recover the probed instruction at addr for further analysis. */
+static int recover_probed_instruction(kprobe_opcode_t *buf, unsigned long addr)
+{
+	struct kprobe *kp;
+	kp = get_kprobe((void *)addr);
+	if (!kp)
+		return -EINVAL;
+
+	/*
+	 *  Basically, kp->ainsn.insn has an original instruction.
+	 *  However, RIP-relative instruction can not do single-stepping
+	 *  at different place, fix_riprel() tweaks the displacement of
+	 *  that instruction. In that case, we can't recover the instruction
+	 *  from the kp->ainsn.insn.
+	 *
+	 *  On the other hand, kp->opcode has a copy of the first byte of
+	 *  the probed instruction, which is overwritten by int3. And
+	 *  the instruction at kp->addr is not modified by kprobes except
+	 *  for the first byte, we can recover the original instruction
+	 *  from it and kp->opcode.
+	 */
+	memcpy(buf, kp->addr, MAX_INSN_SIZE * sizeof(kprobe_opcode_t));
+	buf[0] = kp->opcode;
+	return 0;
+}
+
+/* Dummy buffers for kallsyms_lookup */
+static char __dummy_buf[KSYM_NAME_LEN];
+
+/* Check if paddr is at an instruction boundary */
+static int __kprobes can_probe(unsigned long paddr)
+{
+	int ret;
+	unsigned long addr, offset = 0;
+	struct insn insn;
+	kprobe_opcode_t buf[MAX_INSN_SIZE];
+
+	if (!kallsyms_lookup(paddr, NULL, &offset, NULL, __dummy_buf))
+		return 0;
+
+	/* Decode instructions */
+	addr = paddr - offset;
+	while (addr < paddr) {
+		kernel_insn_init(&insn, (void *)addr);
+		insn_get_opcode(&insn);
+
+		/* Check if the instruction has been modified. */
+		if (insn.opcode.bytes[0] == BREAKPOINT_INSTRUCTION) {
+			ret = recover_probed_instruction(buf, addr);
+			if (ret)
+				/*
+				 * Another debugging subsystem might insert
+				 * this breakpoint. In that case, we can't
+				 * recover it.
+				 */
+				return 0;
+			kernel_insn_init(&insn, buf);
+		}
+		insn_get_length(&insn);
+		addr += insn.length;
+	}
+
+	return (addr == paddr);
+}
+
 /*
  * Returns non-zero if opcode modifies the interrupt flag.
  */

@@ -360,6 +427,8 @@ static void __kprobes arch_copy_kprobe(struct kprobe *p)
 
 int __kprobes arch_prepare_kprobe(struct kprobe *p)
 {
+	if (!can_probe((unsigned long)p->addr))
+		return -EILSEQ;
 	/* insn: must be on special executable page on x86. */
 	p->ainsn.insn = get_insn_slot();
 	if (!p->ainsn.insn)

Masami Hiramatsu

Software Engineer
Hitachi Computer Products (America), Inc.
Software Solutions Division

e-mail: [email protected]

No, it recovers just an instruction which is probed by a kprobe, because we need to know the first byte of this instruction for decoding it.

Perhaps we'd better to have more generic interface (text_peek?) for it because another subsystem (e.g. kgdb) may want to insert int3...

Thank you,

Masami Hiramatsu

Software Engineer
Hitachi Computer Products (America), Inc.
Software Solutions Division

e-mail: [email protected]

Aah, I see now, it's to keep a sane check of the instructions boundaries without int 3 artifacts in the middle.

But in that case, you should re-arm the breakpoint after your check, right?

Or may be you could do the check without repatching? May be by doing a copy of insn.opcode.bytes and replacing bytes[0] with what a random kprobe has stolen?

Ah, sorry, it was not accurate. the function recovers an instruction on the buffer(buf), not on the real kernel text. :)

Yes, it doesn't modify kernel text, just recover an original instruction from kernel text and backup byte on a buffer.

Hm, no, this function is protected from other kprobes by kprobe_mutex.

Thank you,

Masami Hiramatsu

Software Engineer
Hitachi Computer Products (America), Inc.
Software Solutions Division

e-mail: [email protected]

Ah ok. I'll just add a small comment about that then, and apply it.

Ok.

Right, thanks!

Cleanup fix_riprel() in arch/x86/kernel/kprobes.c by using x86 instruction decoder.

---

 arch/x86/kernel/kprobes.c |  128 ++++++++-------------------------------------
 1 files changed, 23 insertions(+), 105 deletions(-)

index 80d493f..98f48d0 100644
@@ -109,50 +109,6 @@ static const u32 twobyte_is_boostable[256 / 32] = {
 	/*      -----------------------------------------------         */
 	/*      0  1  2  3  4  5  6  7  8  9  a  b  c  d  e  f          */
 };
-static const u32 onebyte_has_modrm[256 / 32] = {
-	/*      0  1  2  3  4  5  6  7  8  9  a  b  c  d  e  f          */
-	/*      -----------------------------------------------         */
-	W(0x00, 1, 1, 1, 1, 0, 0, 0, 0, 1, 1, 1, 1, 0, 0, 0, 0) | /* 00 */
-	W(0x10, 1, 1, 1, 1, 0, 0, 0, 0, 1, 1, 1, 1, 0, 0, 0, 0) , /* 10 */
-	W(0x20, 1, 1, 1, 1, 0, 0, 0, 0, 1, 1, 1, 1, 0, 0, 0, 0) | /* 20 */
-	W(0x30, 1, 1, 1, 1, 0, 0, 0, 0, 1, 1, 1, 1, 0, 0, 0, 0) , /* 30 */
-	W(0x40, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0) | /* 40 */
-	W(0x50, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0) , /* 50 */
-	W(0x60, 0, 0, 1, 1, 0, 0, 0, 0, 0, 1, 0, 1, 0, 0, 0, 0) | /* 60 */
-	W(0x70, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0) , /* 70 */
-	W(0x80, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1) | /* 80 */
-	W(0x90, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0) , /* 90 */
-	W(0xa0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0) | /* a0 */
-	W(0xb0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0) , /* b0 */
-	W(0xc0, 1, 1, 0, 0, 1, 1, 1, 1, 0, 0, 0, 0, 0, 0, 0, 0) | /* c0 */
-	W(0xd0, 1, 1, 1, 1, 0, 0, 0, 0, 1, 1, 1, 1, 1, 1, 1, 1) , /* d0 */
-	W(0xe0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0) | /* e0 */
-	W(0xf0, 0, 0, 0, 0, 0, 0, 1, 1, 0, 0, 0, 0, 0, 0, 1, 1)   /* f0 */
-	/*      -----------------------------------------------         */
-	/*      0  1  2  3  4  5  6  7  8  9  a  b  c  d  e  f          */
-};
-static const u32 twobyte_has_modrm[256 / 32] = {
-	/*      0  1  2  3  4  5  6  7  8  9  a  b  c  d  e  f          */
-	/*      -----------------------------------------------         */
-	W(0x00, 1, 1, 1, 1, 0, 0, 0, 0, 0, 0, 0, 0, 0, 1, 0, 1) | /* 0f */
-	W(0x10, 1, 1, 1, 1, 1, 1, 1, 1, 1, 0, 0, 0, 0, 0, 0, 0) , /* 1f */
-	W(0x20, 1, 1, 1, 1, 1, 0, 1, 0, 1, 1, 1, 1, 1, 1, 1, 1) | /* 2f */
-	W(0x30, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0) , /* 3f */
-	W(0x40, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1) | /* 4f */
-	W(0x50, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1) , /* 5f */
-	W(0x60, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1) | /* 6f */
-	W(0x70, 1, 1, 1, 1, 1, 1, 1, 0, 0, 0, 0, 0, 1, 1, 1, 1) , /* 7f */
-	W(0x80, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0) | /* 8f */
-	W(0x90, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1) , /* 9f */
-	W(0xa0, 0, 0, 0, 1, 1, 1, 1, 1, 0, 0, 0, 1, 1, 1, 1, 1) | /* af */
-	W(0xb0, 1, 1, 1, 1, 1, 1, 1, 1, 0, 0, 1, 1, 1, 1, 1, 1) , /* bf */
-	W(0xc0, 1, 1, 1, 1, 1, 1, 1, 1, 0, 0, 0, 0, 0, 0, 0, 0) | /* cf */
-	W(0xd0, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1) , /* df */
-	W(0xe0, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1) | /* ef */
-	W(0xf0, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 0)   /* ff */
-	/*      -----------------------------------------------         */
-	/*      0  1  2  3  4  5  6  7  8  9  a  b  c  d  e  f          */
-};
 #undef W
 
 struct kretprobe_blackpoint kretprobe_blacklist[] = {

@@ -345,68 +301,30 @@ static int __kprobes is_IF_modifier(kprobe_opcode_t *insn)
 static void __kprobes fix_riprel(struct kprobe *p)
 {
 #ifdef CONFIG_X86_64
-	u8 *insn = p->ainsn.insn;
-	s64 disp;
-	int need_modrm;
-
-	/* Skip legacy instruction prefixes.  */
-	while (1) {
-		switch (*insn) {
-		case 0x66:
-		case 0x67:
-		case 0x2e:
-		case 0x3e:
-		case 0x26:
-		case 0x64:
-		case 0x65:
-		case 0x36:
-		case 0xf0:
-		case 0xf3:
-		case 0xf2:
-			++insn;
-			continue;
-		}
-		break;
-	}
+	struct insn insn;
+	kernel_insn_init(&insn, p->ainsn.insn);
 
-	/* Skip REX instruction prefix.  */
-	if (is_REX_prefix(insn))
-		++insn;
-
-	if (*insn == 0x0f) {
-		/* Two-byte opcode.  */
-		++insn;
-		need_modrm = test_bit(*insn,
-				      (unsigned long *)twobyte_has_modrm);
-	} else
-		/* One-byte opcode.  */
-		need_modrm = test_bit(*insn,
-				      (unsigned long *)onebyte_has_modrm);
-
-	if (need_modrm) {
-		u8 modrm = *++insn;
-		if ((modrm & 0xc7) == 0x05) {
-			/* %rip+disp32 addressing mode */
-			/* Displacement follows ModRM byte.  */
-			++insn;
-			/*
-			 * The copied instruction uses the %rip-relative
-			 * addressing mode.  Adjust the displacement for the
-			 * difference between the original location of this
-			 * instruction and the location of the copy that will
-			 * actually be run.  The tricky bit here is making sure
-			 * that the sign extension happens correctly in this
-			 * calculation, since we need a signed 32-bit result to
-			 * be sign-extended to 64 bits when it's added to the
-			 * %rip value and yield the same 64-bit result that the
-			 * sign-extension of the original signed 32-bit
-			 * displacement would have given.
-			 */
-			disp = (u8 *) p->addr + *((s32 *) insn) -
-			       (u8 *) p->ainsn.insn;
-			BUG_ON((s64) (s32) disp != disp); /* Sanity check.  */
-			*(s32 *)insn = (s32) disp;
-		}
+	if (insn_rip_relative(&insn)) {
+		s64 newdisp;
+		u8 *disp;
+		insn_get_displacement(&insn);
+		/*
+		 * The copied instruction uses the %rip-relative addressing
+		 * mode.  Adjust the displacement for the difference between
+		 * the original location of this instruction and the location
+		 * of the copy that will actually be run.  The tricky bit here
+		 * is making sure that the sign extension happens correctly in
+		 * this calculation, since we need a signed 32-bit result to
+		 * be sign-extended to 64 bits when it's added to the %rip
+		 * value and yield the same 64-bit result that the sign-
+		 * extension of the original signed 32-bit displacement would
+		 * have given.
+		 */
+		newdisp = (u8 *) p->addr + (s64) insn.displacement.value -
+			  (u8 *) p->ainsn.insn;
+		BUG_ON((s64) (s32) newdisp != newdisp); /* Sanity check.  */
+		disp = (u8 *) p->ainsn.insn + insn_offset_displacement(&insn);
+		*(s32 *) disp = (s32) newdisp;
 	}
 #endif
 }

Masami Hiramatsu

Software Engineer
Hitachi Computer Products (America), Inc.
Software Solutions Division

e-mail: [email protected]

Add following APIs for accessing registers and stack entries from pt_regs. These APIs are required by kprobes-based event tracer on ftrace. Some other debugging tools might be able to use it too.

- regs_query_register_offset(const char *name)
Query the offset of "name" register.

- regs_query_register_name(unsigned int offset)
Query the name of register by its offset.

- regs_get_register(struct pt_regs *regs, unsigned int offset) Get the value of a register by its offset.

- regs_within_kernel_stack(struct pt_regs *regs, unsigned long addr) Check the address is in the kernel stack.

- regs_get_kernel_stack_nth(struct pt_regs *reg, unsigned int nth) Get Nth entry of the kernel stack. (N >= 0)

- regs_get_argument_nth(struct pt_regs *reg, unsigned int nth) Get Nth argument at function call. (N >= 0)

---

 arch/x86/include/asm/ptrace.h |   62 +++++++++++++++++++++++
 arch/x86/kernel/ptrace.c      |  112 +++++++++++++++++++++++++++++++++++++++++
 2 files changed, 174 insertions(+), 0 deletions(-)

index 0f0d908..a3d49dd 100644
@@ -7,6 +7,7 @@
 
 #ifdef __KERNEL__
 #include <asm/segment.h>
+#include <asm/page_types.h>
 #endif
 
 #ifndef __ASSEMBLY__

@@ -216,6 +217,67 @@ static inline unsigned long user_stack_pointer(struct pt_regs *regs)
 	return regs->sp;
 }
 
+/* Query offset/name of register from its name/offset */
+extern int regs_query_register_offset(const char *name);
+extern const char *regs_query_register_name(unsigned int offset);
+#define MAX_REG_OFFSET (offsetof(struct pt_regs, ss))
+
+/**
+ * regs_get_register() - get register value from its offset
+ * @regs:	pt_regs from which register value is gotten.
+ * @offset:	offset number of the register.
+ *
+ * regs_get_register returns the value of a register whose offset from @regs
+ * is @offset. The @offset is the offset of the register in struct pt_regs.
+ * If @offset is bigger than MAX_REG_OFFSET, this returns 0.
+ */
+static inline unsigned long regs_get_register(struct pt_regs *regs,
+					      unsigned int offset)
+{
+	if (unlikely(offset > MAX_REG_OFFSET))
+		return 0;
+	return *(unsigned long *)((unsigned long)regs + offset);
+}
+
+/**
+ * regs_within_kernel_stack() - check the address in the stack
+ * @regs:	pt_regs which contains kernel stack pointer.
+ * @addr:	address which is checked.
+ *
+ * regs_within_kenel_stack() checks @addr is within the kernel stack page(s).
+ * If @addr is within the kernel stack, it returns true. If not, returns false.
+ */
+static inline int regs_within_kernel_stack(struct pt_regs *regs,
+					   unsigned long addr)
+{
+	return ((addr & ~(THREAD_SIZE - 1))  ==
+		(kernel_stack_pointer(regs) & ~(THREAD_SIZE - 1)));
+}
+
+/**
+ * regs_get_kernel_stack_nth() - get Nth entry of the stack
+ * @regs:	pt_regs which contains kernel stack pointer.
+ * @n:		stack entry number.
+ *
+ * regs_get_kernel_stack_nth() returns @n th entry of the kernel stack which
+ * is specifined by @regs. If the @n th entry is NOT in the kernel stack,
+ * this returns 0.
+ */
+static inline unsigned long regs_get_kernel_stack_nth(struct pt_regs *regs,
+						      unsigned int n)
+{
+	unsigned long *addr = (unsigned long *)kernel_stack_pointer(regs);
+	addr += n;
+	if (regs_within_kernel_stack(regs, (unsigned long)addr))
+		return *addr;
+	else
+		return 0;
+}
+
+/* Get Nth argument at function call */
+extern unsigned long regs_get_argument_nth(struct pt_regs *regs,
+					   unsigned int n);
+
 /*
  * These are defined as per linux/ptrace.h, which see.
  */

Masami Hiramatsu

Software Engineer
Hitachi Computer Products (America), Inc.
Software Solutions Division

e-mail: [email protected]

Add dynamic ftrace_event_call support to ftrace. Trace engines can adds new ftrace_event_call to ftrace on the fly. Each operator functions of the call takes a ftrace_event_call data structure as an argument, because these functions may be shared among several ftrace_event_calls.

Changes from v13:
- Define remove_subsystem_dir() always (revirt a2ca5e03), because trace_remove_event_call() uses it.
- Modify syscall tracer because of ftrace_event_call change.

---

 include/linux/ftrace_event.h  |   14 +++--
 include/linux/syscalls.h      |    4 +
 include/trace/ftrace.h        |   19 +++----
 include/trace/syscall.h       |    8 +--
 kernel/trace/trace_events.c   |  119 +++++++++++++++++++++++++++++------------
 kernel/trace/trace_export.c   |   23 ++++----
 kernel/trace/trace_syscalls.c |   16 +++---
 7 files changed, 125 insertions(+), 78 deletions(-)

index 189806b..9af68ce 100644
@@ -112,13 +112,13 @@ struct ftrace_event_call {
 	struct dentry		*dir;
 	struct trace_event	*event;
 	int			enabled;
-	int			(*regfunc)(void *);
-	void			(*unregfunc)(void *);
+	int			(*regfunc)(struct ftrace_event_call *);
+	void			(*unregfunc)(struct ftrace_event_call *);
 	int			id;
-	int			(*raw_init)(void);
-	int			(*show_format)(struct ftrace_event_call *call,
-					       struct trace_seq *s);
-	int			(*define_fields)(void);
+	int			(*raw_init)(struct ftrace_event_call *);
+	int			(*show_format)(struct ftrace_event_call *,
+					       struct trace_seq *);
+	int			(*define_fields)(struct ftrace_event_call *);
 	struct list_head	fields;
 	int			filter_active;
 	struct event_filter	*filter;

@@ -142,6 +142,8 @@ extern int filter_current_check_discard(struct ftrace_event_call *call,
 
 extern int trace_define_field(struct ftrace_event_call *call, char *type,
 			      char *name, int offset, int size, int is_signed);
+extern int trace_add_event_call(struct ftrace_event_call *call);
+extern void trace_remove_event_call(struct ftrace_event_call *call);
 
 #define is_signed_type(type)	(((type)(-1)) < 0)
 

index 87d06c1..be59d22 100644
@@ -165,7 +165,7 @@ static void prof_sysexit_disable_##sname(struct ftrace_event_call *event_call) \
 	struct trace_event enter_syscall_print_##sname = {		\
 		.trace                  = print_syscall_enter,		\
 	};								\
-	static int init_enter_##sname(void)				\
+	static int init_enter_##sname(struct ftrace_event_call *call)	\
 	{								\
 		int num, id;						\
 		num = syscall_name_to_nr("sys"#sname);			\

@@ -201,7 +201,7 @@ static void prof_sysexit_disable_##sname(struct ftrace_event_call *event_call) \
 	struct trace_event exit_syscall_print_##sname = {		\
 		.trace                  = print_syscall_exit,		\
 	};								\
-	static int init_exit_##sname(void)				\
+	static int init_exit_##sname(struct ftrace_event_call *call)	\
 	{								\
 		int num, id;						\
 		num = syscall_name_to_nr("sys"#sname);			\

index b250b06..6c1b5b1 100644
@@ -294,10 +294,9 @@ ftrace_raw_output_##call(struct trace_iterator *iter, int flags)	\
 #undef TRACE_EVENT
 #define TRACE_EVENT(call, proto, args, tstruct, func, print)		\
 int									\
-ftrace_define_fields_##call(void)					\
+ftrace_define_fields_##call(struct ftrace_event_call *event_call)	\
 {									\
 	struct ftrace_raw_##call field;					\
-	struct ftrace_event_call *event_call = &event_##call;		\
 	int ret;							\
 									\
 	__common_field(int, type, 1);					\

@@ -411,7 +410,7 @@ static void ftrace_profile_disable_##call(struct ftrace_event_call *event_call)\
  *	event_trace_printk(_RET_IP_, "<call>: " <fmt>);
  * }
  *
- * static int ftrace_reg_event_<call>(void)
+ * static int ftrace_reg_event_<call>(struct ftrace_event_call *unused)
  * {
  *	int ret;
  *

@@ -422,7 +421,7 @@ static void ftrace_profile_disable_##call(struct ftrace_event_call *event_call)\
  *	return ret;
  * }
  *
- * static void ftrace_unreg_event_<call>(void)
+ * static void ftrace_unreg_event_<call>(struct ftrace_event_call *unused)
  * {
  *	unregister_trace_<call>(ftrace_event_<call>);
  * }

@@ -455,7 +454,7 @@ static void ftrace_profile_disable_##call(struct ftrace_event_call *event_call)\
  *	trace_current_buffer_unlock_commit(event, irq_flags, pc);
  * }
  *
- * static int ftrace_raw_reg_event_<call>(void)
+ * static int ftrace_raw_reg_event_<call>(struct ftrace_event_call *unused)
  * {
  *	int ret;
  *

@@ -466,7 +465,7 @@ static void ftrace_profile_disable_##call(struct ftrace_event_call *event_call)\
  *	return ret;
  * }
  *
- * static void ftrace_unreg_event_<call>(void)
+ * static void ftrace_unreg_event_<call>(struct ftrace_event_call *unused)
  * {
  *	unregister_trace_<call>(ftrace_raw_event_<call>);
  * }

@@ -475,7 +474,7 @@ static void ftrace_profile_disable_##call(struct ftrace_event_call *event_call)\
  *	.trace			= ftrace_raw_output_<call>, <-- stage 2
  * };
  *
- * static int ftrace_raw_init_event_<call>(void)
+ * static int ftrace_raw_init_event_<call>(struct ftrace_event_call *unused)
  * {
  *	int id;
  *

@@ -569,7 +568,7 @@ static void ftrace_raw_event_##call(proto)				\
 		trace_nowake_buffer_unlock_commit(event, irq_flags, pc); \
 }									\
 									\
-static int ftrace_raw_reg_event_##call(void *ptr)			\
+static int ftrace_raw_reg_event_##call(struct ftrace_event_call *unused)\
 {									\
 	int ret;							\
 									\

@@ -580,7 +579,7 @@ static int ftrace_raw_reg_event_##call(void *ptr)			\
 	return ret;							\
 }									\
 									\
-static void ftrace_raw_unreg_event_##call(void *ptr)			\
+static void ftrace_raw_unreg_event_##call(struct ftrace_event_call *unused)\
 {									\
 	unregister_trace_##call(ftrace_raw_event_##call);		\
 }									\

@@ -589,7 +588,7 @@ static struct trace_event ftrace_event_type_##call = {			\
 	.trace			= ftrace_raw_output_##call,		\
 };									\
 									\
-static int ftrace_raw_init_event_##call(void)				\
+static int ftrace_raw_init_event_##call(struct ftrace_event_call *unused)\
 {									\
 	int id;								\
 									\

index 0cb0362..848b4ae 100644
@@ -51,10 +51,10 @@ void set_syscall_enter_id(int num, int id);
 void set_syscall_exit_id(int num, int id);
 extern struct trace_event event_syscall_enter;
 extern struct trace_event event_syscall_exit;
-extern int reg_event_syscall_enter(void *ptr);
-extern void unreg_event_syscall_enter(void *ptr);
-extern int reg_event_syscall_exit(void *ptr);
-extern void unreg_event_syscall_exit(void *ptr);
+extern int reg_event_syscall_enter(struct ftrace_event_call *call);
+extern void unreg_event_syscall_enter(struct ftrace_event_call *call);
+extern int reg_event_syscall_exit(struct ftrace_event_call *call);
+extern void unreg_event_syscall_exit(struct ftrace_event_call *call);
 extern int
 ftrace_format_syscall(struct ftrace_event_call *call, struct trace_seq *s);
 enum print_line_t print_syscall_enter(struct trace_iterator *iter, int flags);