Skip to contentSkip to conversation

New ark3116 driver - testers needed

DISCUSSION Ondrej Zary 2 participants 3 messages Aug 23, 2009 – Aug 31, 2009 1 message not in the archive

lore
Share & tools
lore

A message that is not in the archive (sent off-list or not yet received): [email protected]

#1 lore raw
Quoted 18 lines · On Sunday 23 August 2009 14:46:16 Bart Hartgers wrote:

Hi All,

I managed to write an improved ark3116 driver after I figured out that it is just an 16450 UART with some USB glue logic.

Compared to the old ark3116 driver it offers the following improvements:
- cts/rts handshake support
- break signalling
- line error detection

Since it is a big step from the previous driver, it made little sense to modify that one, so I created new driver, named ark316new. Also this means that both could coexist if the new one doesn't work for someone.

I have no datasheet, so the driver is entirely based on reverse engineering, and some testing by others would be a good idea.

Quoted 6 lines

I also tried to include the IrDA fixes for the old ark3116.c driver that were posted on this list recently, but I could not test if these work, since I don't have the proper hardware.

Because of this, I would appreciate reports of both success and failure in using this driver.

Good work. I'll try the driver during the week with that USB-to-IrDA thing.

Added LKML to CC.

Signature · 1 line
Ondrej Zary
#2 lore raw
In reply to a message not in the archive
Quoted 18 lines · On Sunday 23 August 2009 14:46:16 Bart Hartgers wrote:

Hi All,

I managed to write an improved ark3116 driver after I figured out that it is just an 16450 UART with some USB glue logic.

Compared to the old ark3116 driver it offers the following improvements:
- cts/rts handshake support
- break signalling
- line error detection

Since it is a big step from the previous driver, it made little sense to modify that one, so I created new driver, named ark316new. Also this means that both could coexist if the new one doesn't work for someone.

I have no datasheet, so the driver is entirely based on reverse engineering, and some testing by others would be a good idea.

Quoted 6 lines

I also tried to include the IrDA fixes for the old ark3116.c driver that were posted on this list recently, but I could not test if these work, since I don't have the proper hardware.

Because of this, I would appreciate reports of both success and failure in using this driver.

Tested the driver today with that Gembird UIR-22.

It did not compile neither in 2.6.30.1 nor in 2.6.31-rc8 with the following error:

ark3116new.c:790: error: unknown field shutdown specified in initializer ark3116new/ark3116new.c:790: warning: initialization from incompatible pointer type

Commenting that line produced a module that worked:
usb 1-1: new full speed USB device using uhci_hcd and address 2 usb 1-1: configuration #0 chosen from 1 choice
usb 1-1: config 0 descriptor??
usbcore: registered new interface driver usbserial
usbserial: USB Serial Driver core
USB Serial support registered for ARK3116 RS232/IrDA ark3116new 1-1:0.0: ARK3116 RS232/IrDA converter detected usb 1-1: ark3116new using IrDA mode
usb 1-1: ARK3116 RS232/IrDA converter now attached to ttyUSB0
usbcore: registered new interface driver ark3116new ark3116new:v0.1:USB ARK3116 serial/IrDA driver
usb 1-1: ark3116new don't know how to do software flow control
NET: Registered protocol family 23

Ran "irattach /dev/ttyUSB0 -s" and then "obexftp -i -l" to list files on Nokia 6230i. It worked fine and file transfer too. So the IrDA mode works.

When I unplugged the device, irattach remained running and some error message was written to console every few seconds (sorry, I haven't recorded it). Killing irattach then resulted in oops. But this might be expected as the shutdown function was commented out.

I think that this driver should replace current ark3116 driver. Having two drivers for the same hardware is a bad thing.

Signature · 1 line
Ondrej Zary
#3 lore raw

2009/8/29 Ondrej Zary <[email protected]>:

Quoted 50 lines · On Sunday 23 August 2009 14:46:16 Bart Hartgers wrote:
Quoted 18 lines

Hi All,

I managed to write an improved ark3116 driver after I figured out that it is just an 16450 UART with some USB glue logic.

Compared to the old ark3116 driver it offers the following improvements:
- cts/rts handshake support
- break signalling
- line error detection

Since it is a big step from the previous driver, it made little sense to modify that one, so I created new driver, named ark316new. Also this means that both could coexist if the new one doesn't work for someone.

I have no datasheet, so the driver is entirely based on reverse engineering, and some testing by others would be a good idea.

Quoted 6 lines

I also tried to include the IrDA fixes for the old ark3116.c driver that were posted on this list recently, but I could not test if these work, since I don't have the proper hardware.

Because of this, I would appreciate reports of both success and failure in using this driver.

Tested the driver today with that Gembird UIR-22.

It did not compile neither in 2.6.30.1 nor in 2.6.31-rc8 with the following error:

ark3116new.c:790: error: unknown field shutdown specified in initializer ark3116new/ark3116new.c:790: warning: initialization from incompatible pointer type

Commenting that line produced a module that worked:
usb 1-1: new full speed USB device using uhci_hcd and address 2 usb 1-1: configuration #0 chosen from 1 choice
usb 1-1: config 0 descriptor??
usbcore: registered new interface driver usbserial
usbserial: USB Serial Driver core
USB Serial support registered for ARK3116 RS232/IrDA ark3116new 1-1:0.0: ARK3116 RS232/IrDA converter detected usb 1-1: ark3116new using IrDA mode
usb 1-1: ARK3116 RS232/IrDA converter now attached to ttyUSB0
usbcore: registered new interface driver ark3116new ark3116new:v0.1:USB ARK3116 serial/IrDA driver
usb 1-1: ark3116new don't know how to do software flow control
NET: Registered protocol family 23

Quoted 8 lines

Ran "irattach /dev/ttyUSB0 -s" and then "obexftp -i -l" to list files on Nokia 6230i. It worked fine and file transfer too. So the IrDA mode works.

When I unplugged the device, irattach remained running and some error message was written to console every few seconds (sorry, I haven't recorded it). Killing irattach then resulted in oops. But this might be expected as the shutdown function was commented out.

Hi Ondrej,

Thanks for testing this!

I later discovered that there is a change with respect to shutdown-functionality between 2.6.28 (on which I made the driver) and 2.6.31. I have to update the driver to 2.6.current anyway.

Quoted 2 lines

I think that this driver should replace current ark3116 driver. Having two drivers for the same hardware is a bad thing.

I agree. However, given the experimental nature of the driver, I would prefer some more testing. Then again, the original driver is lacks some features, and making ark3116new default would increase its exposure ;-).

Groeten,
Bart

Quoted 4 lines

--
Ondrej Zary

Signature · 1 line
Bart Hartgers - New e-mail: [email protected]