Skip to contentSkip to conversation

AT91: Add SD/MMC controller support

PATCH Superseded Albin Tonnerre 5 participants 16 messages Sep 5, 2009 – May 26, 2010 7 messages not in the archive Arm/Microchip (AT91) SoC support

lore
Share & tools
lore
#0 lore raw

PATCH v2 1/1 AT91: Add SD/MMC controller support

This patch allows to use the atmel_mci SD/MMC driver on the at91 architecture. It contains:
- initialization code for the MCI controller for all the supported AT91. It allows the use of only one controller even if a SoC has two controllers (anyway there's no support for it in atmel_mci as of now)
- the necessary get_mci_clk_rate function
- definition of MMCI_BASE for use in atmel_mci
- the cpu_mmc_init function. As of now this is not used, but will be required when atmel_mci is ported to the new generic mmc API.

---
Changes since v1 (http://lists.denx.de/pipermail/u-boot/2009-September/059665.html):
- Fix the MCI controller ID in the init code for CAP9, SAM9263 and SAM9G45
- Move AT91_BASE_MCI* define to soc header
- define AT91_BASE_MCI{0,1} instead of AT91_BASE_MCI for boards which have 2 controllers
- rework the way MMCI_BASE is defined accordingly

Note: I am fully aware that MMCI0_BASE and MMCI1_BASE should be defined, instead of MMCI_BASE. However, I'd rather wait until the patch that switches atmel_mci to the generic mmc API is accepted, as it will be easier to do it then.

 cpu/arm926ejs/at91/at91cap9_devices.c       |   37 ++++++++++++++++++
 cpu/arm926ejs/at91/at91sam9260_devices.c    |   27 +++++++++++++
 cpu/arm926ejs/at91/at91sam9261_devices.c    |   18 +++++++++
 cpu/arm926ejs/at91/at91sam9263_devices.c    |   55 +++++++++++++++++++++++++++
 cpu/arm926ejs/at91/at91sam9m10g45_devices.c |   55 +++++++++++++++++++++++++++
 cpu/arm926ejs/at91/at91sam9rl_devices.c     |   22 +++++++++++
 cpu/arm926ejs/at91/cpu.c                    |    7 +++
 include/asm-arm/arch-at91/at91_common.h     |    2 +
 include/asm-arm/arch-at91/at91cap9.h        |    3 +
 include/asm-arm/arch-at91/at91sam9260.h     |    2 +
 include/asm-arm/arch-at91/at91sam9261.h     |    1 +
 include/asm-arm/arch-at91/at91sam9263.h     |    3 +
 include/asm-arm/arch-at91/at91sam9g45.h     |    3 +
 include/asm-arm/arch-at91/at91sam9rl.h      |    1 +
 include/asm-arm/arch-at91/clk.h             |    5 ++
 include/asm-arm/arch-at91/memory-map.h      |    6 +++
 16 files changed, 247 insertions(+), 0 deletions(-)
cpu/arm926ejs/at91/at91cap9_devices.c +37 -0
index 39e405f..53a58a9 100644
@@ -79,6 +79,43 @@ void at91_serial_hw_init(void)
 #endif
 }
 
+#ifdef CONFIG_ATMEL_MCI
+#ifdef CONFIG_AT91_MCI0
+void at91_mci0_hw_init(unsigned long mask)
+{
+	at91_sys_write(AT91_PMC_PCER, 1 << AT91CAP9_ID_MCI0);
+	at91_set_A_periph(AT91_PIN_PA2, 0);
+
+	if (mask & (1 << 0)) {
+		at91_set_A_periph(AT91_PIN_PA0, 1);
+		at91_set_A_periph(AT91_PIN_PA1, 1);
+		if (mask & (1 << 1)) {
+			at91_set_A_periph(AT91_PIN_PA3, 1);
+			at91_set_A_periph(AT91_PIN_PA4, 1);
+			at91_set_A_periph(AT91_PIN_PA5, 1);
+		}
+	}
+}
+#endif
+#ifdef CONFIG_AT91_MCI1
+void at91_mci1_hw_init(unsigned long mask)
+{
+	at91_sys_write(AT91_PMC_PCER, 1 << AT91CAP9_ID_MCI1);
+	at91_set_A_periph(AT91_PIN_PA16, 0);
+
+	if (mask & (1 << 0)) {
+		at91_set_A_periph(AT91_PIN_PA17, 1);
+		at91_set_A_periph(AT91_PIN_PA18, 1);
+		if (mask & (1 << 1)) {
+			at91_set_A_periph(AT91_PIN_PA19, 1);
+			at91_set_A_periph(AT91_PIN_PA20, 1);
+			at91_set_A_periph(AT91_PIN_PA21, 1);
+		}
+	}
+}
+#endif
+#endif
+
 #ifdef CONFIG_HAS_DATAFLASH
 void at91_spi0_hw_init(unsigned long cs_mask)
 {
cpu/arm926ejs/at91/at91sam9260_devices.c +27 -0
index f86cb99..ea22030 100644
@@ -75,6 +75,33 @@ void at91_serial_hw_init(void)
 #endif
 }
 
+#ifdef CONFIG_ATMEL_MCI
+void at91_mci0_hw_init(unsigned long mask)
+{
+	at91_sys_write(AT91_PMC_PCER, 1 << AT91SAM9260_ID_MCI);
+	at91_set_A_periph(AT91_PIN_PA8, 0);
+
+	if (mask & (1 << 0)) {
+		at91_set_A_periph(AT91_PIN_PA6, 1);
+		at91_set_A_periph(AT91_PIN_PA7, 1);
+		if (mask & (1 << 1)) {
+			at91_set_A_periph(AT91_PIN_PA9, 1);
+			at91_set_A_periph(AT91_PIN_PA10, 1);
+			at91_set_A_periph(AT91_PIN_PA11, 1);
+		}
+	}
+	if (mask & (1 << 2)) {
+		at91_set_B_periph(AT91_PIN_PA0, 1);
+		at91_set_B_periph(AT91_PIN_PA1, 1);
+		if (mask & (1 << 3)) {
+			at91_set_B_periph(AT91_PIN_PA3, 1);
+			at91_set_B_periph(AT91_PIN_PA4, 1);
+			at91_set_B_periph(AT91_PIN_PA5, 1);
+		}
+	}
+}
+#endif /* ATMEL_MCI */
+
 #if defined(CONFIG_HAS_DATAFLASH) || defined(CONFIG_ATMEL_SPI)
 void at91_spi0_hw_init(unsigned long cs_mask)
 {
cpu/arm926ejs/at91/at91sam9261_devices.c +18 -0
index 16d411f..7ee573c 100644
@@ -75,6 +75,24 @@ void at91_serial_hw_init(void)
 #endif
 }
 
+#ifdef CONFIG_ATMEL_MCI
+void at91_mci0_hw_init(unsigned long mask)
+{
+	at91_sys_write(AT91_PMC_PCER, 1 << AT91SAM9261_ID_MCI);
+	at91_set_B_periph(AT91_PIN_PA2, 0);
+
+	if (mask & (1 << 0)) {
+		at91_set_B_periph(AT91_PIN_PA0, 1);
+		at91_set_B_periph(AT91_PIN_PA1, 1);
+		if (mask & (1 << 1)) {
+			at91_set_B_periph(AT91_PIN_PA4, 1);
+			at91_set_B_periph(AT91_PIN_PA5, 1);
+			at91_set_B_periph(AT91_PIN_PA6, 1);
+		}
+	}
+}
+#endif /* ATMEL_MCI */
+
 #ifdef CONFIG_HAS_DATAFLASH
 void at91_spi0_hw_init(unsigned long cs_mask)
 {
cpu/arm926ejs/at91/at91sam9263_devices.c +55 -0

61 lines not on this page · raw message

cpu/arm926ejs/at91/at91sam9m10g45_devices.c +55 -0

61 lines not on this page · raw message

cpu/arm926ejs/at91/at91sam9rl_devices.c +22 -0
index ebed193..41ae4a8 100644
@@ -75,6 +75,28 @@ void at91_serial_hw_init(void)
 #endif
 }
 
+/* 
+ * The AT91SAM9RL64 is said to have 2 slots, but the datasheet doesn't
+ * seem to mention to what pins the second slot is assigned
+ */
+#ifdef CONFIG_ATMEL_MCI
+void at91_mci0_hw_init(unsigned long mask)
+{
+	at91_sys_write(AT91_PMC_PCER, 1 << AT91SAM9260_ID_MCI);
+	at91_set_A_periph(AT91_PIN_PA2, 0);
+
+	if (mask & (1 << 0)) {
+		at91_set_A_periph(AT91_PIN_PA0, 1);
+		at91_set_A_periph(AT91_PIN_PA1, 1);
+		if (mask & (1 << 1)) {
+			at91_set_A_periph(AT91_PIN_PA3, 1);
+			at91_set_A_periph(AT91_PIN_PA4, 1);
+			at91_set_A_periph(AT91_PIN_PA5, 1);
+		}
+	}
+}
+#endif /* ATMEL_MCI */
+
 #ifdef CONFIG_HAS_DATAFLASH
 void at91_spi0_hw_init(unsigned long cs_mask)
 {
cpu/arm926ejs/at91/cpu.c +7 -0
index f2f7b62..f96b715 100644
@@ -52,3 +52,10 @@ int print_cpuinfo(void)
 	return 0;
 }
 #endif
+
+#ifdef CONFIG_GENERIC_MMC
+int cpu_mmc_init(bd_t *bis)
+{
+	atmel_mci_init(bis);
+}
+#endif /* GENERIC_MMC */
include/asm-arm/arch-at91/at91_common.h +2 -0
index 01840ee..01fcdd6 100644
@@ -32,6 +32,8 @@ void at91_serial0_hw_init(void);
 void at91_serial1_hw_init(void);
 void at91_serial2_hw_init(void);
 void at91_serial3_hw_init(void);
+void at91_mci0_hw_init(unsigned long mask);
+void at91_mci1_hw_init(unsigned long mask);
 void at91_spi0_hw_init(unsigned long cs_mask);
 void at91_spi1_hw_init(unsigned long cs_mask);
 void at91_uhp_hw_init(void);
include/asm-arm/arch-at91/at91cap9.h +3 -0
index b128ac5..2ad3280 100644
@@ -109,6 +109,9 @@
 #define AT91_USART1	AT91CAP9_BASE_US1
 #define AT91_USART2	AT91CAP9_BASE_US2
 
+#define AT91_BASE_MCI0	AT91CAP9_BASE_MCI0
+#define AT91_BASE_MCI1	AT91CAP9_BASE_MCI1
+
 /*
  * SCKCR flags
  */
include/asm-arm/arch-at91/at91sam9260.h +2 -0
index 73975f4..b92f0ee 100644
@@ -105,6 +105,8 @@
 #define AT91_USART4	AT91SAM9260_BASE_US4
 #define AT91_USART5	AT91SAM9260_BASE_US5
 
+#define AT91_BASE_MCI0	AT91SAM9260_BASE_MCI
+
 /*
  * Internal Memory.
  */
include/asm-arm/arch-at91/at91sam9261.h +1 -0
index b303e07..11fdc3e 100644
@@ -88,6 +88,7 @@
 #define AT91_USART1	AT91SAM9261_BASE_US1
 #define AT91_USART2	AT91SAM9261_BASE_US2
 
+#define AT91_BASE_MCI0	AT91SAM9261_BASE_MCI
 
 /*
  * Internal Memory.
include/asm-arm/arch-at91/at91sam9263.h +3 -0
index 966a683..6bf124b 100644
@@ -108,6 +108,9 @@
 #define AT91_SMC	AT91_SMC0
 #define AT91_SDRAMC	AT91_SDRAMC0
 
+#define AT91_BASE_MCI0	AT91SAM9263_BASE_MCI0
+#define AT91_BASE_MCI1	AT91SAM9263_BASE_MCI1
+
 /*
  * Internal Memory.
  */
include/asm-arm/arch-at91/at91sam9g45.h +3 -0
index 0feed9c..16deadc 100644
@@ -114,6 +114,9 @@
 #define AT91_USART2	AT91SAM9G45_BASE_US2
 #define AT91_USART3	AT91SAM9G45_BASE_US3
 
+#define AT91_BASE_MCI0	AT91SAM9G45_BASE_MCI0
+#define AT91_BASE_MCI1	AT91SAM9G45_BASE_MCI1
+
 /*
  * Internal Memory.
  */
include/asm-arm/arch-at91/at91sam9rl.h +1 -0
index 4dd8037..f0da7a2 100644
@@ -99,6 +99,7 @@
 #define AT91_USART2	AT91SAM9RL_BASE_US2
 #define AT91_USART3	AT91SAM9RL_BASE_US3
 
+#define AT91_BASE_MCI0	AT91SAM9RL_BASE_MCI
 
 /*
  * Internal Memory.
include/asm-arm/arch-at91/clk.h +5 -0
index f642dd9..457e6c9 100644
@@ -59,5 +59,10 @@ static inline unsigned long get_twi_clk_rate(unsigned int dev_id)
 	return get_mck_clk_rate();
 }
 
+static inline unsigned long get_mci_clk_rate(void)
+{
+	return get_mck_clk_rate();
+}
+
 int at91_clock_init(unsigned long main_clock);
 #endif /* __ASM_ARM_ARCH_CLK_H__ */
include/asm-arm/arch-at91/memory-map.h +6 -0
index f605f37..445d128 100644
@@ -32,4 +32,10 @@
 #define USART3_BASE (AT91_BASE_SYS + AT91_DBGU)
 #define SPI0_BASE	AT91_BASE_SPI
 
+#ifndef (CONFIG_AT91_MCI1)
+#  define MMCI_BASE AT91_BASE_MCI0
+#else
+#  define MMCI_BASE AT91_BASE_MCI1
+#endif
+
 #endif /* __ASM_ARM_ARCH_MEMORYMAP_H__ */
Signature · 1 line
1.6.3.3
#1 lore raw

PATCH v3 1/1 AT91: Add SD/MMC controller support

This patch allows to use the atmel_mci SD/MMC driver on the at91 architecture. It contains:
- initialization code for the MCI controller for all the supported AT91. It allows the use of only one controller even if a SoC has two controllers (anyway there's no support for it in atmel_mci as of now)
- the necessary get_mci_clk_rate function
- definition of MMCI_BASE for use in atmel_mci
- the cpu_mmc_init function. As of now this is not used, but will be required when atmel_mci is ported to the new generic mmc API.

---
Changes since v1
- Fix the MCI controller ID in the init code for CAP9, SAM9263 and SAM9G45
- Move AT91_BASE_MCI* define to soc header
- define AT91_BASE_MCI{0,1} instead of AT91_BASE_MCI for boards which have 2 controllers
- rework the way MMCI_BASE is defined accordingly

Changes since v2
- allow using 8-bit bus width on CPUs that support it
- change the arguments of atmel_mciX_hw_init to (slot, bus) so that it's more meaningful than (bitmask)

 cpu/arm926ejs/at91/at91cap9_devices.c       |   40 +++++++++++++++
 cpu/arm926ejs/at91/at91sam9260_devices.c    |   37 ++++++++++++++
 cpu/arm926ejs/at91/at91sam9261_devices.c    |   21 ++++++++
 cpu/arm926ejs/at91/at91sam9263_devices.c    |   72 +++++++++++++++++++++++++++
 cpu/arm926ejs/at91/at91sam9m10g45_devices.c |   56 +++++++++++++++++++++
 cpu/arm926ejs/at91/at91sam9rl_devices.c     |   25 +++++++++
 include/asm-arm/arch-at91/at91_common.h     |    2 +
 include/asm-arm/arch-at91/at91cap9.h        |    2 +
 include/asm-arm/arch-at91/at91sam9260.h     |    1 +
 include/asm-arm/arch-at91/at91sam9261.h     |    1 +
 include/asm-arm/arch-at91/at91sam9263.h     |    2 +
 include/asm-arm/arch-at91/at91sam9g45.h     |    2 +
 include/asm-arm/arch-at91/at91sam9rl.h      |    1 +
 include/asm-arm/arch-at91/clk.h             |    5 ++
 include/asm-arm/arch-at91/memory-map.h      |    6 ++
 15 files changed, 273 insertions(+), 0 deletions(-)
cpu/arm926ejs/at91/at91cap9_devices.c +40 -0
index 39e405f..de7048b 100644
@@ -79,6 +79,46 @@ void at91_serial_hw_init(void)
 #endif
 }
 
+#ifdef CONFIG_ATMEL_MCI
+void at91_mci0_hw_init(int slot, int bus_width)
+{
+	at91_sys_write(AT91_PMC_PCER, 1 << AT91CAP9_ID_MCI0);
+
+	/* CLK */
+	at91_set_A_periph(AT91_PIN_PA2, 0);
+
+	/* CMD */
+	at91_set_A_periph(AT91_PIN_PA1, 1);
+
+	/* DAT0, maybe DAT1..DAT3 */
+	at91_set_A_periph(AT91_PIN_PA0, 1);
+	if (bus_width == 4) {
+		at91_set_A_periph(AT91_PIN_PA3, 1);
+		at91_set_A_periph(AT91_PIN_PA4, 1);
+		at91_set_A_periph(AT91_PIN_PA5, 1);
+	}
+}
+
+void at91_mci1_hw_init(int slot, int bus_width)
+{
+	at91_sys_write(AT91_PMC_PCER, 1 << AT91CAP9_ID_MCI0);
+
+	/* CLK */
+	at91_set_A_periph(AT91_PIN_PA16, 0);
+
+	/* CMD */
+	at91_set_A_periph(AT91_PIN_PA17, 1);
+
+	/* DAT0, maybe DAT1..DAT3 */
+	at91_set_A_periph(AT91_PIN_PA18, 1);
+	if (bus_width == 4) {
+		at91_set_A_periph(AT91_PIN_PA19, 1);
+		at91_set_A_periph(AT91_PIN_PA20, 1);
+		at91_set_A_periph(AT91_PIN_PA21, 1);
+	}
+}
+#endif
+
 #ifdef CONFIG_HAS_DATAFLASH
 void at91_spi0_hw_init(unsigned long cs_mask)
 {
cpu/arm926ejs/at91/at91sam9260_devices.c +37 -0
index f86cb99..f724f58 100644
@@ -75,6 +75,43 @@ void at91_serial_hw_init(void)
 #endif
 }
 
+#ifdef CONFIG_ATMEL_MCI
+void at91_mci0_hw_init(int slot, int bus_width)
+{
+	at91_sys_write(AT91_PMC_PCER, 1 << AT91SAM9260_ID_MCI);
+
+	/* CLK */
+	at91_set_A_periph(AT91_PIN_PA8, 0);
+
+	switch (slot) {
+		case 0:
+			/* CMD */
+			at91_set_A_periph(AT91_PIN_PA7, 1);
+
+			/* DAT0, maybe DAT1..DAT3 */
+			at91_set_A_periph(AT91_PIN_PA6, 1);
+			if (bus_width == 4) {
+				at91_set_A_periph(AT91_PIN_PA9, 1);
+				at91_set_A_periph(AT91_PIN_PA10, 1);
+				at91_set_A_periph(AT91_PIN_PA11, 1);
+			}
+			break;
+		case 1:
+			/* CMD */
+			at91_set_B_periph(AT91_PIN_PA1, 1);
+
+			/* DAT0, maybe DAT1..DAT3 */
+			at91_set_B_periph(AT91_PIN_PA0, 1);
+			if (bus_width == 4) {
+				at91_set_B_periph(AT91_PIN_PA3, 1);
+				at91_set_B_periph(AT91_PIN_PA4, 1);
+				at91_set_B_periph(AT91_PIN_PA5, 1);
+			}
+			break;
+	}
+}
+#endif /* ATMEL_MCI */
+
 #if defined(CONFIG_HAS_DATAFLASH) || defined(CONFIG_ATMEL_SPI)
 void at91_spi0_hw_init(unsigned long cs_mask)
 {
cpu/arm926ejs/at91/at91sam9261_devices.c +21 -0
index 16d411f..be76acf 100644
@@ -75,6 +75,27 @@ void at91_serial_hw_init(void)
 #endif
 }
 
+#ifdef CONFIG_ATMEL_MCI
+void at91_mci0_hw_init(int slot, int bus_width)
+{
+	at91_sys_write(AT91_PMC_PCER, 1 << AT91SAM9261_ID_MCI);
+
+	/* CLK */
+	at91_set_B_periph(AT91_PIN_PA2, 0);
+
+	/* CMD */
+	at91_set_B_periph(AT91_PIN_PA1, 1);
+
+	/* DAT0, maybe DAT1..DAT3 */
+	at91_set_B_periph(AT91_PIN_PA0, 1);
+	if (bus_width == 4) {
+		at91_set_B_periph(AT91_PIN_PA4, 1);
+		at91_set_B_periph(AT91_PIN_PA5, 1);
+		at91_set_B_periph(AT91_PIN_PA6, 1);
+	}
+}
+#endif /* ATMEL_MCI */
+
 #ifdef CONFIG_HAS_DATAFLASH
 void at91_spi0_hw_init(unsigned long cs_mask)
 {
cpu/arm926ejs/at91/at91sam9263_devices.c +72 -0

78 lines not on this page · raw message

cpu/arm926ejs/at91/at91sam9m10g45_devices.c +56 -0

62 lines not on this page · raw message

cpu/arm926ejs/at91/at91sam9rl_devices.c +25 -0
index ebed193..3945e13 100644
@@ -75,6 +75,31 @@ void at91_serial_hw_init(void)
 #endif
 }
 
+/* 
+ * The AT91SAM9RL64 is said to have 2 slots, but the datasheet doesn't
+ * seem to mention to what pins the second slot is assigned
+ */
+#ifdef CONFIG_ATMEL_MCI
+void at91_mci0_hw_init(int slot, int bus_width)
+{
+	at91_sys_write(AT91_PMC_PCER, 1 << AT91SAM9RL_ID_MCI);
+
+	/* CLK */
+	at91_set_A_periph(AT91_PIN_PA2, 0);
+
+	/* CMD */
+	at91_set_A_periph(AT91_PIN_PA1, 1);
+
+	/* DAT0, maybe DAT1..DAT3 */
+	at91_set_A_periph(AT91_PIN_PA0, 1);
+	if (bus_width == 4) {
+		at91_set_A_periph(AT91_PIN_PA3, 1);
+		at91_set_A_periph(AT91_PIN_PA4, 1);
+		at91_set_A_periph(AT91_PIN_PA5, 1);
+	}
+}
+#endif /* ATMEL_MCI */
+
 #ifdef CONFIG_HAS_DATAFLASH
 void at91_spi0_hw_init(unsigned long cs_mask)
 {
include/asm-arm/arch-at91/at91_common.h +2 -0
index 01840ee..1c96b40 100644
@@ -32,6 +32,8 @@ void at91_serial0_hw_init(void);
 void at91_serial1_hw_init(void);
 void at91_serial2_hw_init(void);
 void at91_serial3_hw_init(void);
+void at91_mci0_hw_init(int slot, int bus_width);
+void at91_mci1_hw_init(int slot, int bus_width);
 void at91_spi0_hw_init(unsigned long cs_mask);
 void at91_spi1_hw_init(unsigned long cs_mask);
 void at91_uhp_hw_init(void);
include/asm-arm/arch-at91/at91cap9.h +2 -0
index 98bfcc7..de731ac 100644
@@ -112,6 +112,8 @@
 #define AT91_BASE_SPI	AT91CAP9_BASE_SPI0
 #define AT91_ID_UHP	AT91CAP9_ID_UHP
 #define AT91_PMC_UHP	AT91CAP9_PMC_UHP
+#define AT91_BASE_MCI0	AT91CAP9_BASE_MCI0
+#define AT91_BASE_MCI1	AT91CAP9_BASE_MCI1
 
 /*
  * SCKCR flags
include/asm-arm/arch-at91/at91sam9260.h +1 -0
index f2aef8a..6b26140 100644
@@ -108,6 +108,7 @@
 #define AT91_BASE_SPI	AT91SAM9260_BASE_SPI0
 #define AT91_ID_UHP	AT91SAM9260_ID_UHP
 #define AT91_PMC_UHP	AT91SAM926x_PMC_UHP
+#define AT91_BASE_MCI0	AT91SAM9260_BASE_MCI
 
 /*
  * Internal Memory.
include/asm-arm/arch-at91/at91sam9261.h +1 -0
index 55bd49a..48fb8f4 100644
@@ -91,6 +91,7 @@
 #define AT91_BASE_SPI	AT91SAM9261_BASE_SPI0
 #define AT91_ID_UHP	AT91SAM9261_ID_UHP
 #define AT91_PMC_UHP	AT91SAM926x_PMC_UHP
+#define AT91_BASE_MCI0	AT91SAM9261_BASE_MCI
 
 /*
  * Internal Memory.
include/asm-arm/arch-at91/at91sam9263.h +2 -0
index d862129..4f29e65 100644
@@ -111,6 +111,8 @@
 #define AT91_BASE_SPI	AT91SAM9263_BASE_SPI0
 #define AT91_ID_UHP	AT91SAM9263_ID_UHP
 #define AT91_PMC_UHP	AT91SAM926x_PMC_UHP
+#define AT91_BASE_MCI0	AT91SAM9263_BASE_MCI0
+#define AT91_BASE_MCI1	AT91SAM9263_BASE_MCI1
 
 /*
  * Internal Memory.
include/asm-arm/arch-at91/at91sam9g45.h +2 -0
index d02b157..f232600 100644
@@ -118,6 +118,8 @@
 #define AT91_BASE_SPI	AT91SAM9G45_BASE_SPI0
 #define AT91_ID_UHP	AT91SAM9G45_ID_UHPHS
 #define AT91_PMC_UHP	AT91SAM926x_PMC_UHP
+#define AT91_BASE_MCI0	AT91SAM9G45_BASE_MCI0
+#define AT91_BASE_MCI1	AT91SAM9G45_BASE_MCI1
 
 /*
  * Internal Memory.
include/asm-arm/arch-at91/at91sam9rl.h +1 -0
index 3638f92..d26a607 100644
@@ -101,6 +101,7 @@
 
 #define AT91_BASE_SPI	AT91SAM9RL_BASE_SPI
 #define AT91_ID_UHP	AT91SAM9RL_ID_UHP
+#define AT91_BASE_MCI0	AT91SAM9RL_BASE_MCI
 
 
 /*
include/asm-arm/arch-at91/clk.h +5 -0
index f642dd9..457e6c9 100644
@@ -59,5 +59,10 @@ static inline unsigned long get_twi_clk_rate(unsigned int dev_id)
 	return get_mck_clk_rate();
 }
 
+static inline unsigned long get_mci_clk_rate(void)
+{
+	return get_mck_clk_rate();
+}
+
 int at91_clock_init(unsigned long main_clock);
 #endif /* __ASM_ARM_ARCH_CLK_H__ */
include/asm-arm/arch-at91/memory-map.h +6 -0
index f605f37..de0aba7 100644
@@ -32,4 +32,10 @@
 #define USART3_BASE (AT91_BASE_SYS + AT91_DBGU)
 #define SPI0_BASE	AT91_BASE_SPI
 
+#ifndef CONFIG_AT91_MCI1
+#define MMCI_BASE AT91_BASE_MCI0
+#else
+#define MMCI_BASE AT91_BASE_MCI1
+#endif
+
 #endif /* __ASM_ARM_ARCH_MEMORYMAP_H__ */
Signature · 1 line
1.6.3.3
#2 lore raw

PATCH v3 1/1 AT91: Add SD/MMC controller support

Dear Albin Tonnerre,

Quoted 20 lines · In message <1252442374-25386-1-git-send-email-albin.tonnerre@free-electrons.com…

This patch allows to use the atmel_mci SD/MMC driver on the at91 architecture. It contains:
- initialization code for the MCI controller for all the supported AT91. It allows the use of only one controller even if a SoC has two controllers (anyway there's no support for it in atmel_mci as of now)
- the necessary get_mci_clk_rate function
- definition of MMCI_BASE for use in atmel_mci
- the cpu_mmc_init function. As of now this is not used, but will be required when atmel_mci is ported to the new generic mmc API.

---
Changes since v1
- Fix the MCI controller ID in the init code for CAP9, SAM9263 and SAM9G45
- Move AT91_BASE_MCI* define to soc header
- define AT91_BASE_MCI{0,1} instead of AT91_BASE_MCI for boards which have 2 controllers
- rework the way MMCI_BASE is defined accordingly

Quoted 4 lines

Changes since v2
- allow using 8-bit bus width on CPUs that support it
- change the arguments of atmel_mciX_hw_init to (slot, bus) so that it's more meaningful than (bitmask)

What's the current state of this patch? Do you consider it ripe for inclusion into mainline, or do you still have changes pending?

Best regards,

Wolfgang Denk

Signature · 10 lines
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
Q:  How many DEC repairman does it take to fix a flat?
A:  Five; four to hold the car up and one to swap tires.
Q:  How long does it take?
A:  It's indeterminate.  It will depend upon how many flats they've
    brought with them.
Q:  What happens if you've got TWO flats?
A:  They replace your generator.
#3 lore raw

PATCH v3 1/1 AT91: Add SD/MMC controller support

Quoted 23 lines · Wolfgang Denk

Dear Albin Tonnerre,

Quoted 20 lines · In message <1252442374-25386-1-git-send-email-albin.tonnerre@free-electrons.com…

This patch allows to use the atmel_mci SD/MMC driver on the at91 architecture. It contains:
- initialization code for the MCI controller for all the supported AT91. It allows the use of only one controller even if a SoC has two controllers (anyway there's no support for it in atmel_mci as of now)
- the necessary get_mci_clk_rate function
- definition of MMCI_BASE for use in atmel_mci
- the cpu_mmc_init function. As of now this is not used, but will be required when atmel_mci is ported to the new generic mmc API.

---
Changes since v1
- Fix the MCI controller ID in the init code for CAP9, SAM9263 and SAM9G45
- Move AT91_BASE_MCI* define to soc header
- define AT91_BASE_MCI{0,1} instead of AT91_BASE_MCI for boards which have 2 controllers
- rework the way MMCI_BASE is defined accordingly

Quoted 7 lines
Quoted 4 lines

Changes since v2
- allow using 8-bit bus width on CPUs that support it
- change the arguments of atmel_mciX_hw_init to (slot, bus) so that it's more meaningful than (bitmask)

What's the current state of this patch? Do you consider it ripe for inclusion into mainline, or do you still have changes pending?

I consider it ready for inclusion. Thanks for the heads-up.

Regards,

Signature · 4 lines
Albin Tonnerre, Free Electrons
Kernel, drivers and embedded Linux development,
consulting, training and support.
http://free-electrons.com

A message that is not in the archive (sent off-list or not yet received): F32E8C2599F37641BB4E3F3AC4A3C412014625AC54B7@ws

A message that is not in the archive (sent off-list or not yet received): [email protected]

#6 lore raw

PATCH v2 1/1 AT91: Add SD/MMC controller support & [PATCH v3]

Hi Albin,

Quoted 10 lines

Someone encoutered the same issue: http://lists.denx.de/pipermail/u-boot/2009-September/059684.html
This is because the patch is based on a change that was part of another patch that added support to a new >board. You can work around this easily: in at91sam9260_devices.c, simply replace

#if defined(CONFIG_HAS_DATAFLASH) || defined(CONFIG_ATMEL_SPI)

with

#if defined(CONFIG_HAS_DATAFLASH)

and the patch should then apply cleanly. Please let me know if that still doesn't work.

Yes this patch apply cleanly, but I had problems on my samg20ek to get the mmc working. On the command mmc init, it always say no mmc card foung.

So I tried now to apply your new Patch V3. What is the Base of this patch (I tried again u-boot 2009.08) Is there a better way to download the version with git?

There I have a lot of problems.

patching file cpu/arm926ejs/at91/at91cap9_devices.c
patching file cpu/arm926ejs/at91/at91sam9260_devices.c
Hunk #1 FAILED at 75.
1 out of 1 hunk FAILED -- saving rejects to file cpu/arm926ejs/at91/at91sam9260_devices.c.rej patching file cpu/arm926ejs/at91/at91sam9261_devices.c
patching file cpu/arm926ejs/at91/at91sam9263_devices.c
patching file cpu/arm926ejs/at91/at91sam9m10g45_devices.c
patching file cpu/arm926ejs/at91/at91sam9rl_devices.c
patching file include/asm-arm/arch-at91/at91_common.h
patching file include/asm-arm/arch-at91/at91cap9.h
Hunk #1 FAILED at 112.
1 out of 1 hunk FAILED -- saving rejects to file include/asm-arm/arch-at91/at91cap9.h.rej patching file include/asm-arm/arch-at91/at91sam9260.h
Hunk #1 FAILED at 108.
1 out of 1 hunk FAILED -- saving rejects to file include/asm-arm/arch-at91/at91sam9260.h.rej patching file include/asm-arm/arch-at91/at91sam9261.h
Hunk #1 FAILED at 91.
1 out of 1 hunk FAILED -- saving rejects to file include/asm-arm/arch-at91/at91sam9261.h.rej patching file include/asm-arm/arch-at91/at91sam9263.h
Hunk #1 FAILED at 111.
1 out of 1 hunk FAILED -- saving rejects to file include/asm-arm/arch-at91/at91sam9263.h.rej patching file include/asm-arm/arch-at91/at91sam9g45.h
Hunk #1 FAILED at 118.
1 out of 1 hunk FAILED -- saving rejects to file include/asm-arm/arch-at91/at91sam9g45.h.rej patching file include/asm-arm/arch-at91/at91sam9rl.h
Hunk #1 FAILED at 101.
1 out of 1 hunk FAILED -- saving rejects to file include/asm-arm/arch-at91/at91sam9rl.h.rej patching file include/asm-arm/arch-at91/clk.h
patching file include/asm-arm/arch-at91/memory-map.h

bye
Konrad

#7 lore raw

PATCH v2 1/1 AT91: Add SD/MMC controller support & [PATCH v3]

Quoted 8 lines · Konrad Mattheis

Hi Albin,

Quoted 4 lines

Someone encoutered the same issue: http://lists.denx.de/pipermail/u-boot/2009-September/059684.html
This is because the patch is based on a change that was part of another patch that added support to a new >board. You can work around this easily: in at91sam9260_devices.c, simply replace

#if defined(CONFIG_HAS_DATAFLASH) || defined(CONFIG_ATMEL_SPI)

Quoted 7 lines
Quoted 5 lines

with

#if defined(CONFIG_HAS_DATAFLASH)

and the patch should then apply cleanly. Please let me know if that still doesn't work.

Yes this patch apply cleanly, but I had problems on my samg20ek to get the mmc working. On the command mmc init, it always say no mmc card foung.

What modifications have you done to your code after applying the patch? Providing the diff would help spotting potential errors

Quoted 3 lines

So I tried now to apply your new Patch V3. What is the Base of this patch (I tried again u-boot 2009.08) Is there a better way to download the version with git?

It applies on top of http://lists.denx.de/pipermail/u-boot/2009-September/060053.html
The best base to apply those patches is the current master branch of the git repository (git://git.denx.de/u-boot.git)

Regards,

Signature · 11 lines
Albin Tonnerre, Free Electrons
Kernel, drivers and embedded Linux development,
consulting, training and support.
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 835 bytes
Desc: Digital signature
Url : http://lists.denx.de/pipermail/u-boot/attachments/20090909/4fd858ba/attachment.pgp 
#8 lore raw

PATCH v3 1/1 AT91: Problems with SD

Hi Albin,

so I describe you what I did.

Downloaded u-boot 2009.08

changed:

Quoted 1 line

#if defined(CONFIG_HAS_DATAFLASH)

to:

Quoted 1 line

#if defined(CONFIG_HAS_DATAFLASH) || defined(CONFIG_ATMEL_SPI)

applied Patch:
http://lists.denx.de/pipermail/u-boot/2009-September/060053.html

then applied Patch V3: from mail

added to:include/config/at91sam9260ek.h

#define CONFIG_CMD_MMC 1
#define CONFIG_MMC 1
#define CONFIG_ATMEL_MCI

compiled and the on the at91sam9g20ek
I can start a normal kernel,...
but if I write mmc init I get the following error:

Quoted 2 lines

mmc: clock 150000 too low; setting CLKDIV to 255
No MMC card found

After this I tried to download git://git.denx.de/u-boot.git and then I could not apply the patches. I always got this message:
Reversed (or previously applied) patch detected! Assume -R? [n]
Did you already applied the patches to the git repository?

bye Konrad

#9 lore raw

PATCH v3 1/1 AT91: Problems with SD

Quoted 18 lines · Konrad Mattheis

Hi Albin,

so I describe you what I did.

Downloaded u-boot 2009.08

changed:

Quoted 1 line

#if defined(CONFIG_HAS_DATAFLASH)

to:

Quoted 1 line

#if defined(CONFIG_HAS_DATAFLASH) || defined(CONFIG_ATMEL_SPI)

applied Patch:
http://lists.denx.de/pipermail/u-boot/2009-September/060053.html

then applied Patch V3: from mail

added to:include/config/at91sam9260ek.h

Quoted 7 lines

#define CONFIG_CMD_MMC 1
#define CONFIG_MMC 1
#define CONFIG_ATMEL_MCI

compiled and the on the at91sam9g20ek
I can start a normal kernel,...
but if I write mmc init I get the following error:

Ok, so that's what I thought: you're missing a call to at91_mciX_hw_init in your board init code. This function assigns the correst I/O pins to the MCI controller and takes care of enabling the clock. Please have a look at at91_mciX_hw_init cpu/arm926ejs/at91/at91sam9260_devices.c to see what arguments the function expects.

Quoted 7 lines
Quoted 2 lines

mmc: clock 150000 too low; setting CLKDIV to 255
No MMC card found

After this I tried to download git://git.denx.de/u-boot.git and then I could not apply the patches. I always got this message:
Reversed (or previously applied) patch detected! Assume -R? [n]
Did you already applied the patches to the git repository?

The CONFIG_ATMEL_SPI change is in mainline, yes. Other parts of the patch aren't.

Regards,

Signature · 4 lines
Albin Tonnerre, Free Electrons
Kernel, drivers and embedded Linux development,
consulting, training and support.
http://free-electrons.com

A message that is not in the archive (sent off-list or not yet received): F32E8C2599F37641BB4E3F3AC4A3C412014625AC54DA@ws

A message that is not in the archive (sent off-list or not yet received): [email protected]

A message that is not in the archive (sent off-list or not yet received): F32E8C2599F37641BB4E3F3AC4A3C412014625AC54DB@ws

A message that is not in the archive (sent off-list or not yet received): [email protected]

A message that is not in the archive (sent off-list or not yet received): F32E8C2599F37641BB4E3F3AC4A3C412014625AC54DE@ws

#15 lore raw

PATCH v3 1/1 AT91: Problems with SD

Hi Konrad,

Quoted 2 lines · Konrad Mattheis

I will try this later on the day. What is the Base for this patch? Again 2009.08 or do I have to apply other patches?

2009.08 is fine.

Quoted 2 lines

You wrote in this message that this is a port to the new generic mmc api.
Do I also have to make different initialization? Like CONFIG_GENERIC_MMC instead of CONFIG_AT91_MMC

You need CONFIG_GENERIC_MMC in addition to CONFIG_ATMEL_MCI, not instead of.

Regards,

Signature · 4 lines
Albin Tonnerre, Free Electrons
Kernel, drivers and embedded Linux development,
consulting, training and support.
http://free-electrons.com
#16 lore raw

PATCH v3 1/1 AT91: Add SD/MMC controller support

In reply to Albin Tonnerre

Hello there,

I tried to get mmc working on a board using an at91sam9g20. The mmc-card is wired on slotb.

I applied the patches:

http://lists.denx.de/pipermail/u-boot/2009-September/060053.html
http://lists.denx.de/pipermail/u-boot/2009-August/059456.html
http://lists.denx.de/pipermail/u-boot/2009-September/060243.html

It didn't work as I always got (apart from the message of a too low clock which I avoided by setting f_min / f_max on my own):

mmc: command 8 failed (status: 0x0010c1e5)
mmc: command 55 failed (status: 0x0010c1e5)
mmc: command 1 failed (status: 0x0010c1e5)
Card did not respond to voltage select!

So I had a look at linux sources and discovered that the MCI selected the wrong slot. After modifying atmel_mci_set_ios() to set SDCR to use slotb ("mmci_writel(SDCR, sdcr | 1);") I got my card working.

Hope this helps someone.

Regards

Sebastian Heutling

#17 lore raw

[U-Boot] AT91 working SD with u-boot

Hi,

for me this is working:

Downloaded u-boot 2009.08

file cpu/arm926ejs/at91/at91sam9260_devices.c

Quoted 5 lines

changed:

Quoted 1 line

#if defined(CONFIG_HAS_DATAFLASH)

to:

Quoted 1 line

#if defined(CONFIG_HAS_DATAFLASH) || defined(CONFIG_ATMEL_SPI)

patches:

SOC headers:
http://lists.denx.de/pipermail/u-boot/2009-September/060053.html

SD Patch V3
http://lists.denx.de/pipermail/u-boot/2009-September/060243.html

MCI support
http://lists.denx.de/pipermail/u-boot/2009-August/059595.html

add to board init code:

at91_mciX_hw_init (X for mci unit 0 / 1) for parameters have a look at cpu/arm926ejs/at91/at91sam9260_devices.c

bye
Konrad Mattheis

#18 lore raw

[U-Boot] AT91 working SD with u-boot

Hi Konrad,

are you using the AT91SAM9G20-EK?

In that case the difference between us is that I'm working on a different board which is using the slotb MCI while the AT91SAM9G20-EK uses slota.

In case of slota it just worked because MCI_SDCR is 0 on reset but for slotb the SDCSEL field must be set to 1.

Regards

Sebastian Heutling

Quoted 33 lines · Konrad Mattheis

Hi,

for me this is working:

Downloaded u-boot 2009.08

file cpu/arm926ejs/at91/at91sam9260_devices.c

Quoted 5 lines

changed:

Quoted 1 line

#if defined(CONFIG_HAS_DATAFLASH)

to:

Quoted 1 line

#if defined(CONFIG_HAS_DATAFLASH) || defined(CONFIG_ATMEL_SPI)

patches:

SOC headers:
http://lists.denx.de/pipermail/u-boot/2009-September/060053.html

SD Patch V3
http://lists.denx.de/pipermail/u-boot/2009-September/060243.html

MCI support
http://lists.denx.de/pipermail/u-boot/2009-August/059595.html

add to board init code:

at91_mciX_hw_init (X for mci unit 0 / 1) for parameters have a look at cpu/arm926ejs/at91/at91sam9260_devices.c

bye
Konrad Mattheis

#19 lore raw

[U-Boot] AT91 working SD with u-boot

Hi Sebastian,

yes I'm using an AT91SAM9G20-EK Rev.c with two SD slots. I used slot a but I think you just have to init slot b.

in PatchV3 you can read:

Quoted 6 lines

at91_mci0_hw_init(int slot, int bus_width)

switch (slot) {
		case 0:
			.....
		case 1:

So I think you just have to call at91_mci0_hw_init(1,4) for slot b.

bye
Konrad

Quoted 59 lines

-----Urspr?ngliche Nachricht-----
Von: Sebastian Heutling [mailto:heutling at who-ing.de]
Gesendet: Donnerstag, 1. Oktober 2009 10:26
An: Konrad Mattheis
Cc: u-boot at lists.denx.de
Betreff: Re: AT91 working SD with u-boot

Hi Konrad,

are you using the AT91SAM9G20-EK?

In that case the difference between us is that I'm working on a different board which is using the slotb MCI while the AT91SAM9G20-EK uses slota.

In case of slota it just worked because MCI_SDCR is 0 on reset but for slotb the SDCSEL field must be set to 1.

Regards

Sebastian Heutling

Quoted 21 lines · Konrad Mattheis

Hi,

for me this is working:

Downloaded u-boot 2009.08

file cpu/arm926ejs/at91/at91sam9260_devices.c

Quoted 5 lines

changed:

Quoted 1 line

#if defined(CONFIG_HAS_DATAFLASH)

to:

Quoted 1 line

#if defined(CONFIG_HAS_DATAFLASH) || defined(CONFIG_ATMEL_SPI)

patches:

SOC headers:
http://lists.denx.de/pipermail/u-boot/2009-September/060053.html

SD Patch V3
http://lists.denx.de/pipermail/u-boot/2009-September/060243.html

Quoted 6 lines

MCI support
http://lists.denx.de/pipermail/u-boot/2009-August/059595.html

add to board init code:

at91_mciX_hw_init (X for mci unit 0 / 1) for parameters have a look

at cpu/arm926ejs/at91/at91sam9260_devices.c

Quoted 6 lines

bye
Konrad Mattheis

#20 lore raw

[U-Boot] AT91 working SD with u-boot

Hi Konrad,

Quoted 7 lines · Konrad Mattheis

Hi Sebastian,

yes I'm using an AT91SAM9G20-EK Rev.c with two SD slots. I used slot a but I think you just have to init slot b.

in PatchV3 you can read:

Quoted 8 lines
Quoted 6 lines

at91_mci0_hw_init(int slot, int bus_width)

switch (slot) {
		case 0:
			.....
		case 1:

So I think you just have to call at91_mci0_hw_init(1,4) for slot b.

No - that is not enough. It just enables the clock for MCI and configures the pins. But the MCI itself needs to know which slot to address.

Suppose you want to use both slots at the same time (and the drivers would support that).
Then you would call:

at91_mci0_hw_init(0, 4)
at91_mci0_hw_init(1, 4)

In order to access both slots the driver (atmel_mci) needs to select which slot to address. And that is what the SDCSEL field of MCI-SDCR is for (see also Datasheet of the AT91SAM9G20 35.9.4 (probably at page 607)).

Regards

Sebastian

#21 lore raw

[U-Boot] AT91 working SD with u-boot

Quoted 28 lines · Sebastian Heutling

Hi Konrad,

Quoted 7 lines · Konrad Mattheis

Hi Sebastian,

yes I'm using an AT91SAM9G20-EK Rev.c with two SD slots. I used slot a but I think you just have to init slot b.

in PatchV3 you can read:

Quoted 8 lines
Quoted 6 lines

at91_mci0_hw_init(int slot, int bus_width)

switch (slot) {
		case 0:
			.....
		case 1:

So I think you just have to call at91_mci0_hw_init(1,4) for slot b.

No - that is not enough. It just enables the clock for MCI and configures the pins. But the MCI itself needs to know which slot to address.

Suppose you want to use both slots at the same time (and the drivers would support that).
Then you would call:

Quoted 6 lines

at91_mci0_hw_init(0, 4)
at91_mci0_hw_init(1, 4)

In order to access both slots the driver (atmel_mci) needs to select which slot to address. And that is what the SDCSEL field of MCI-SDCR is for (see also Datasheet of the AT91SAM9G20 35.9.4 (probably at page 607)).

But the driver doesn't support for the moment. I might add such support if I have some time (and if that works - has anybody ever tried doing that with Linux?). For now the best way to get it working is to select the correct slot in your board config code.

Cheers,

Signature · 11 lines
Albin Tonnerre, Free Electrons
Kernel, drivers and embedded Linux development,
consulting, training and support.
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 836 bytes
Desc: Digital signature
Url : http://lists.denx.de/pipermail/u-boot/attachments/20091004/ac8252e4/attachment.pgp 
#22 lore raw

[U-Boot] AT91 working SD with u-boot

In reply to Sebastian Heutling
Quoted 9 lines · Sebastian Heutling <heutling <at> who-ing.de> writes:

Hi Konrad,

are you using the AT91SAM9G20-EK?

In that case the difference between us is that I'm working on a different board which is using the slotb MCI while the AT91SAM9G20-EK uses slota.

Quoted 35 lines

In case of slota it just worked because MCI_SDCR is 0 on reset but for slotb the SDCSEL field must be set to 1.

Regards

Sebastian Heutling

Quoted 27 lines · Konrad Mattheis

Hi,

for me this is working:

Downloaded u-boot 2009.08

file cpu/arm926ejs/at91/at91sam9260_devices.c

Quoted 5 lines

changed:

Quoted 1 line

#if defined(CONFIG_HAS_DATAFLASH)

to:

Quoted 1 line

#if defined(CONFIG_HAS_DATAFLASH) || defined(CONFIG_ATMEL_SPI)

patches:

SOC headers:
http://lists.denx.de/pipermail/u-boot/2009-September/060053.html

SD Patch V3
http://lists.denx.de/pipermail/u-boot/2009-September/060243.html

MCI support
http://lists.denx.de/pipermail/u-boot/2009-August/059595.html

add to board init code:

at91_mciX_hw_init (X for mci unit 0 / 1) for parameters have a look at

cpu/arm926ejs/at91/at91sam9260_devices.c

Quoted 7 lines
Quoted 6 lines

bye
Konrad Mattheis

Hello,

Thanks a lot for your post. Could you please let me know what configurations are to be added to /include/configs/board.h file to enable MMC/SD support. I've added the following configurations

/* MMC/SD Support */

/* To include File system support for MMC */
#define CONFIG_DOS_PARTITION
#define CONFIG_CMD_EXT2
#define CONFIG_CMD_FAT
#define CONFIG_MMC
#define CONFIG_GENERIC_MMC
#define CONFIG_DAVINCI_MMC
#define CONFIG_CMD_MM

/* To enable Environment variables to reside on MMC. */
#define CONFIG_DOS_PARTITION 1
//#undef CONFIG_MMC
#define CONFIG_SYS_MMC_BASE 0xFFFB4000
#define CONFIG_SYS_MMC_BLOCKSIZE 512

and when I enter mmcinit, u-boot says command not found. Please find the logs:
and thanks alot for your time :)

Electrum> mmcElectrum> mmc
Usage:
MMC sub system
Electrum> mmcinit
Unknown command 'mmcinit' - try 'help'
Electrum> mmcinfo
MMC Device 0 not found

Thanks,
Kalyan.