rt2500pci is spamming syslogd since upgrade to 2.6.31
A message that is not in the archive (sent off-list or not yet received): 20090915174233.7db381cd@varda
Hi,
Quoted 11 lines
Hi; my syslog has many entries like this since the upgrade to 2.6.31
phy0 ->
rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).Sometimes the driver just start spamming like crazy sometimes is at less rate sometimes it does not appear.
I'm running 2.6.31 with a revert [1] config follows. If more info is needed just ask
Try disabling powersaving,
iwconfig wlan0 power off
Ivo
2009/9/16 Ivo van Doorn <[email protected]>:
Quoted 9 lines
Hi,
Quoted 7 lines
Hi; my syslog has many entries like this since the upgrade to 2.6.31
phy0 ->
rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).Sometimes the driver just start spamming like crazy sometimes is at less rate sometimes it does not appear.
Quoted 8 lines
Quoted 4 lines
I'm running 2.6.31 with a revert [1] config follows. If more info is needed just ask
Try disabling powersaving,
iwconfig wlan0 power off
I have an identical problem, which is fixed by this command.
It is possible to detect that the chip doesn't, for whatever reason, support powersaving and disable it in the driver?
Thanks,
Signature · 4 lines
Julian Calaby Email: [email protected] .Plan: http://sites.google.com/site/juliancalaby/
Quoted 15 lines · Julian Calaby
2009/9/16 Ivo van Doorn <[email protected]>:
Quoted 14 lines
Hi,
Quoted 11 lines
Hi; my syslog has many entries like this since the upgrade to 2.6.31
phy0 ->
rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).Sometimes the driver just start spamming like crazy sometimes is at less rate sometimes it does not appear.
I'm running 2.6.31 with a revert [1] config follows. If more info is needed just ask
Quoted 8 lines
Quoted 3 lines
Try disabling powersaving,
iwconfig wlan0 power off
I have an identical problem, which is fixed by this command.
It is possible to detect that the chip doesn't, for whatever reason, support powersaving and disable it in the driver?
Well I simply have to:
a) fix the driver to handle powersaving better
b) disable powersaving support for the driver
It will probably be (b) first followed by (a) much later if I ever get the time to look into the issue.
Ivo
Quoted 25 lines · Ivo Van Doorn
Quoted 15 lines · Julian Calaby
2009/9/16 Ivo van Doorn <[email protected]>:
Quoted 14 lines
Hi,
Quoted 11 lines
Hi; my syslog has many entries like this since the upgrade to 2.6.31
phy0 ->
rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).Sometimes the driver just start spamming like crazy sometimes is at less rate sometimes it does not appear.
I'm running 2.6.31 with a revert [1] config follows. If more info is needed just ask
Quoted 8 lines
Quoted 3 lines
Try disabling powersaving,
iwconfig wlan0 power off
I have an identical problem, which is fixed by this command.
It is possible to detect that the chip doesn't, for whatever reason, support powersaving and disable it in the driver?
Quoted 6 lines
Well I simply have to:
a) fix the driver to handle powersaving better
b) disable powersaving support for the driverIt will probably be (b) first followed by (a) much later if I ever get the time to look into the issue.
Fair enough.
I'll take a look if I get an opportunity.
Thanks,
Signature · 4 lines
Julian Calaby Email: [email protected] .Plan: http://sites.google.com/site/juliancalaby/