Skip to contentSkip to conversation

Explicitly putting a PCI device to ACPI D0

DISCUSSION Michal Witkowski 3 participants 4 messages Sep 16, 2009

lore
Share & tools
lore
#0 lore raw

Hi,

I've been searching for my answer for a while now, and since I haven't found it anywhere, I've decided to post to LKML, hoping that someone here can help me.

First, I'll explain the background of my problem. My grief is the switchable GPU in my Lenovo Ideapad U330. The BIOS supports two options "Discrete only" (only the ATI card is visible on the BUS) and "Switchable" (both ATI and Intel card visible on the bus). The problem is the lack of a third option "Integrated", in which only the Intel card would be powered off. Lenovo refused to introduce such an option into the BIOS, stating that it's a feature request and not a bug.

To save battery power I'd like to be able to run on the Intel card. However, with the "Switchable" option, powertop indicates huge power usage (24W), which can only be explained by the fact that both cards draw power.

Thus, my question is the following:
Is there a way to explicitly put a device into ACPI D0? I would like to do that to the ATI card on boot.

I've tried the following code:
http://ftp.chg.ru/pub/parallel/scyld/diag/pci-config.c
But it didn't work (the ATI card was still on).

Cheers,
Michal

#1 lore raw
Quoted 20 lines · On Wed, 16 Sep 2009 09:10:24 +0200 Michal Witkowski <[email protected]> wrote:

Hi,

I've been searching for my answer for a while now, and since I haven't found it anywhere, I've decided to post to LKML, hoping that someone here can help me.

First, I'll explain the background of my problem. My grief is the switchable GPU in my Lenovo Ideapad U330. The BIOS supports two options "Discrete only" (only the ATI card is visible on the BUS) and "Switchable" (both ATI and Intel card visible on the bus). The problem is the lack of a third option "Integrated", in which only the Intel card would be powered off. Lenovo refused to introduce such an option into the BIOS, stating that it's a feature request and not a bug.

To save battery power I'd like to be able to run on the Intel card. However, with the "Switchable" option, powertop indicates huge power usage (24W), which can only be explained by the fact that both cards draw power.

Quoted 7 lines

Thus, my question is the following:
Is there a way to explicitly put a device into ACPI D0? I would like to do that to the ATI card on boot.

I've tried the following code:
http://ftp.chg.ru/pub/parallel/scyld/diag/pci-config.c
But it didn't work (the ATI card was still on).

Your best bet might be to load a driver for the ATI card that puts it into PCI D3 state until used. There may be other ways to save power on the disabled part as well...

Alex, is this something you've looked at at all?

Signature · 1 line
Jesse Barnes, Intel Open Source Technology Center
#2 lore raw
Quoted 31 lines · Jesse Barnes
Quoted 20 lines · On Wed, 16 Sep 2009 09:10:24 +0200 Michal Witkowski <[email protected]> wrote:

Hi,

I've been searching for my answer for a while now, and since I haven't found it anywhere, I've decided to post to LKML, hoping that someone here can help me.

First, I'll explain the background of my problem. My grief is the switchable GPU in my Lenovo Ideapad U330. The BIOS supports two options "Discrete only" (only the ATI card is visible on the BUS) and "Switchable" (both ATI and Intel card visible on the bus). The problem is the lack of a third option "Integrated", in which only the Intel card would be powered off. Lenovo refused to introduce such an option into the BIOS, stating that it's a feature request and not a bug.

To save battery power I'd like to be able to run on the Intel card. However, with the "Switchable" option, powertop indicates huge power usage (24W), which can only be explained by the fact that both cards draw power.

Quoted 7 lines

Thus, my question is the following:
Is there a way to explicitly put a device into ACPI D0? I would like to do that to the ATI card on boot.

I've tried the following code:
http://ftp.chg.ru/pub/parallel/scyld/diag/pci-config.c
But it didn't work (the ATI card was still on).

Quoted 5 lines

Your best bet might be to load a driver for the ATI card that puts it into PCI D3 state until used.  There may be other ways to save power on the disabled part as well...

Alex, is this something you've looked at at all?

The xf86-video-ati ddx can turn off the displays and reduce the clocks and pcie lanes, but I haven't sorted out all the D3 stuff yet. As for the switchable graphics, you might find the page below useful. No idea if it will work or fry your hardware:
http://ubuntuforums.org/showthread.php?p=7944950

Alex

#3 lore raw
Quoted 8 lines · On Wednesday 16 of September 2009 18:33:58 you wrote:

The xf86-video-ati ddx can turn off the displays and reduce the clocks and pcie lanes, but I haven't sorted out all the D3 stuff yet. As for the switchable graphics, you might find the page below useful. No idea if it will work or fry your hardware:
http://ubuntuforums.org/showthread.php?p=7944950

Alex

Thank you very very much :)
The above kernel module worked wonders for me.

Cheers,
Michal