AVerTV MCE 116 Plus radio
PATCH 1/1 AVerTV MCE 116 Plus radio
Added FM radio support to Avermedia AVerTV MCE 116 Plus card
linux/drivers/media/video/ivtv/ivtv-cards.c +1 -0
@@ -965,6 +965,7 @@ { IVTV_CARD_INPUT_AUD_TUNER, CX25840_AUDIO5 }, { IVTV_CARD_INPUT_LINE_IN1, CX25840_AUDIO_SERIAL, 1 }, }, + .radio_input = { IVTV_CARD_INPUT_AUD_TUNER, CX25840_AUDIO5 },/* enable line-in */ .gpio_init = { .direction = 0xe000, .initial_value = 0x4000 }, .xceive_pin = 10,
Quoted 2 lines · Aleksandr V. Piskunov
Added FM radio support to Avermedia AVerTV MCE 116 Plus card
What leaves me puzzled, radio only works ok with ivtv newi2c=1
With default newi2c audio is tinny, metallic, with some strange static. Similar problem with pvr-150 was reported years ago, guess issue is still unresolved, perhaps something with cx25840..
Quoted 9 lines · Aleksandr V. Piskunov
Quoted 2 lines · Aleksandr V. Piskunov
Added FM radio support to Avermedia AVerTV MCE 116 Plus card
What leaves me puzzled, radio only works ok with ivtv newi2c=1
With default newi2c audio is tinny, metallic, with some strange static. Similar problem with pvr-150 was reported years ago, guess issue is still unresolved, perhaps something with cx25840..
This particular "tinny" audio problem is definitely I2C speed related, to be more precise, audio only goes bad if i2c-algo-bit is being run with udelay less than 15, i.e. i2c bus frequency is higher than 30 KHz.
So with default udelay=10 or udelay=5 (optimal for IR reciever on that board) radio goes bad. Running with newi2c=1 is ok, but again it isn't optimal for IR reciever on AVerTV M116.
I2C reads/writes to cx25840 themself are ok, verified using register readback after each write/write4. Problem seems to be that with cx25840 register writes coming too fast on higher i2c bus speed, switching register 0x808 _from_ TV standard autodetection mode (0xff) _to_ FM radio mode (0xf9) leaves chip audio detection routine in inconsistent state.
The only solution I found is to do standard routine (assert_reset + write + deassert_reset) followed by 50ms delay and another reset.
Following patch works_for_me, can be improved to only delay/doublereset when really needed, etc. Andy, could you comment/review?
linux/drivers/media/video/cx25840/cx25840-core.c +7 -1
@@ -626,7 +642,13 @@if (state->radio) {cx25840_write (client,0x808 ,0xf9 );cx25840_write (client,0x80b ,0x00 ); - } +/* Double reset cx2384x after setting FM radio mode, helps to +avoid "tinny" audio when ivtv I2C bus is being run on +frequency higher than 30 KHz */ +cx25840_and_or (client,0x810 , ~0x01 ,0 ); +msleep (50 ); +cx25840_and_or (client,0x810 , ~0x01 ,1 ); + }else if (std &V4L2_STD_525_60 ) {/* Certain Hauppauge PVR150 models have a hardware bug that causes audio to drop out. For these models the
Quoted 25 lines · Aleksandr V. Piskunov
Quoted 9 lines · Aleksandr V. Piskunov
Quoted 2 lines · Aleksandr V. Piskunov
Added FM radio support to Avermedia AVerTV MCE 116 Plus card
What leaves me puzzled, radio only works ok with ivtv newi2c=1
With default newi2c audio is tinny, metallic, with some strange static. Similar problem with pvr-150 was reported years ago, guess issue is still unresolved, perhaps something with cx25840..
This particular "tinny" audio problem is definitely I2C speed related, to be more precise, audio only goes bad if i2c-algo-bit is being run with udelay less than 15, i.e. i2c bus frequency is higher than 30 KHz.
So with default udelay=10 or udelay=5 (optimal for IR reciever on that board) radio goes bad. Running with newi2c=1 is ok, but again it isn't optimal for IR reciever on AVerTV M116.
I2C reads/writes to cx25840 themself are ok, verified using register readback after each write/write4. Problem seems to be that with cx25840 register writes coming too fast on higher i2c bus speed, switching register
0x808_from_ TV standard autodetection mode (0xff) _to_ FM radio mode (0xf9) leaves chip audio detection routine in inconsistent state.
Quoted 5 lines
The only solution I found is to do standard routine (
assert_reset+ write +deassert_reset) followed by 50ms delay and another reset.Following patch
works_for_me, can be improved to only delay/doublereset when really needed, etc. Andy, could you comment/review?
Aleksandr,
I will when I get time. This past week and next few weeks are very busy for me for personal (non-linux) reasons. I'll try to get caught up with the patches I still have to rework and then look at this.
Obviously, your patch is fairly straightforward and looks OK. I just haven't checked for any implications. The "general" tinny audio problem with the CX25840 on ivtv boards is *always* resolved with an audio microcontroller reset.
The problem is the microcontroller may restart its detection loop and tinny audio may return. Can you run FM radio for a long time (a day ?), and see if it ever goes back to tinny audio?
Regards,
Andy
Quoted 20 lines
linux/drivers/media/video/cx25840/cx25840-core.c +7
-1@@ -626,7 +642,13 @@if (state->radio) {cx25840_write (client,0x808 ,0xf9 );cx25840_write (client,0x80b ,0x00 ); - } +/* Double reset cx2384x after setting FM radio mode, helps to +avoid "tinny" audio when ivtv I2C bus is being run on +frequency higher than 30 KHz */ +cx25840_and_or (client,0x810 , ~0x01 ,0 ); +msleep (50 ); +cx25840_and_or (client,0x810 , ~0x01 ,1 ); + }else if (std &V4L2_STD_525_60 ) {/* Certain Hauppauge PVR150 models have a hardware bug that causes audio to drop out. For these models the
Quoted 25 lines · Aleksandr V. Piskunov
Quoted 9 lines · Aleksandr V. Piskunov
Quoted 2 lines · Aleksandr V. Piskunov
Added FM radio support to Avermedia AVerTV MCE 116 Plus card
What leaves me puzzled, radio only works ok with ivtv newi2c=1
With default newi2c audio is tinny, metallic, with some strange static. Similar problem with pvr-150 was reported years ago, guess issue is still unresolved, perhaps something with cx25840..
This particular "tinny" audio problem is definitely I2C speed related, to be more precise, audio only goes bad if i2c-algo-bit is being run with udelay less than 15, i.e. i2c bus frequency is higher than 30 KHz.
So with default udelay=10 or udelay=5 (optimal for IR reciever on that board) radio goes bad. Running with newi2c=1 is ok, but again it isn't optimal for IR reciever on AVerTV M116.
I2C reads/writes to cx25840 themself are ok, verified using register readback after each write/write4. Problem seems to be that with cx25840 register writes coming too fast on higher i2c bus speed, switching register
0x808_from_ TV standard autodetection mode (0xff) _to_ FM radio mode (0xf9) leaves chip audio detection routine in inconsistent state.
Quoted 5 lines
The only solution I found is to do standard routine (
assert_reset+ write +deassert_reset) followed by 50ms delay and another reset.Following patch
works_for_me, can be improved to only delay/doublereset when really needed, etc. Andy, could you comment/review?
Aleksandr,
Could you provide your Signed-off-by for this patch? I'm going to commit it as is.
Thanks,
Andy
Quoted 24 lines
linux/drivers/media/video/cx25840/cx25840-core.c +7
-2@@ -626,7 +642,13 @@if (state->radio) {cx25840_write (client,0x808 ,0xf9 );cx25840_write (client,0x80b ,0x00 ); - } +/* Double reset cx2384x after setting FM radio mode, helps to +avoid "tinny" audio when ivtv I2C bus is being run on +frequency higher than 30 KHz */ +cx25840_and_or (client,0x810 , ~0x01 ,0 ); +msleep (50 ); +cx25840_and_or (client,0x810 , ~0x01 ,1 ); + }else if (std &V4L2_STD_525_60 ) {/* Certain Hauppauge PVR150 models have a hardware bug that causes audio to drop out. For these models the -- To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Hi Andy,
This patch has never been applied or nacked. From your last comment, it seems that you're waiting for Aleksandr Signed-of-by:.
If this is still the case, I suggest you to wait for a couple days. If he doesn't send it, it is safe to add it without his SOB, since it is really a trivial change.
Cheers,
Mauro.
Quoted 67 lines · Andy Walls
Quoted 23 lines · Aleksandr V. Piskunov
Quoted 8 lines · Aleksandr V. Piskunov
Quoted 2 lines · Aleksandr V. Piskunov
Added FM radio support to Avermedia AVerTV MCE 116 Plus card
What leaves me puzzled, radio only works ok with ivtv newi2c=1
With default newi2c audio is tinny, metallic, with some strange static. Similar problem with pvr-150 was reported years ago, guess issue is still unresolved, perhaps something with cx25840..
This particular "tinny" audio problem is definitely I2C speed related, to be more precise, audio only goes bad if i2c-algo-bit is being run with udelay less than 15, i.e. i2c bus frequency is higher than 30 KHz.
So with default udelay=10 or udelay=5 (optimal for IR reciever on that board) radio goes bad. Running with newi2c=1 is ok, but again it isn't optimal for IR reciever on AVerTV M116.
I2C reads/writes to cx25840 themself are ok, verified using register readback after each write/write4. Problem seems to be that with cx25840 register writes coming too fast on higher i2c bus speed, switching register
0x808_from_ TV standard autodetection mode (0xff) _to_ FM radio mode (0xf9) leaves chip audio detection routine in inconsistent state.Quoted 5 lines
The only solution I found is to do standard routine (
assert_reset+ write +deassert_reset) followed by 50ms delay and another reset.Following patch
works_for_me, can be improved to only delay/doublereset when really needed, etc. Andy, could you comment/review?Aleksandr,
Could you provide your Signed-off-by for this patch? I'm going to commit it as is.
Thanks,
AndyQuoted 20 lines
linux/drivers/media/video/cx25840/cx25840-core.c +7
-2@@ -626,7 +642,13 @@if (state->radio) {cx25840_write (client,0x808 ,0xf9 );cx25840_write (client,0x80b ,0x00 ); - } +/* Double reset cx2384x after setting FM radio mode, helps to +avoid "tinny" audio when ivtv I2C bus is being run on +frequency higher than 30 KHz */ +cx25840_and_or (client,0x810 , ~0x01 ,0 ); +msleep (50 ); +cx25840_and_or (client,0x810 , ~0x01 ,1 ); + }else if (std &V4L2_STD_525_60 ) {/* Certain Hauppauge PVR150 models have a hardware bug that causes audio to drop out. For these models the -- Quoted 4 lines
To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html--
To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Signature · 2 lines
Cheers, Mauro
Quoted 7 lines · Mauro Carvalho Chehab
Hi Andy,
This patch has never been applied or nacked. From your last comment, it seems that you're waiting for Aleksandr Signed-of-by:.
If this is still the case, I suggest you to wait for a couple days. If he doesn't send it, it is safe to add it without his SOB, since it is really a trivial change.
I'd like to look at this one once more. The extra 50 ms and another reset may be avoidable.
cx25840-core.c:set_input() gets called for s_frequency so I'd like not to add 50 ms if not needed.
Regards,
Andy
Quoted 73 lines
Cheers,
Mauro.Quoted 67 lines · Andy Walls
Quoted 23 lines · Aleksandr V. Piskunov
Quoted 8 lines · Aleksandr V. Piskunov
Quoted 2 lines · Aleksandr V. Piskunov
Added FM radio support to Avermedia AVerTV MCE 116 Plus card
What leaves me puzzled, radio only works ok with ivtv newi2c=1
With default newi2c audio is tinny, metallic, with some strange static. Similar problem with pvr-150 was reported years ago, guess issue is still unresolved, perhaps something with cx25840..
This particular "tinny" audio problem is definitely I2C speed related, to be more precise, audio only goes bad if i2c-algo-bit is being run with udelay less than 15, i.e. i2c bus frequency is higher than 30 KHz.
So with default udelay=10 or udelay=5 (optimal for IR reciever on that board) radio goes bad. Running with newi2c=1 is ok, but again it isn't optimal for IR reciever on AVerTV M116.
I2C reads/writes to cx25840 themself are ok, verified using register readback after each write/write4. Problem seems to be that with cx25840 register writes coming too fast on higher i2c bus speed, switching register
0x808_from_ TV standard autodetection mode (0xff) _to_ FM radio mode (0xf9) leaves chip audio detection routine in inconsistent state.Quoted 5 lines
The only solution I found is to do standard routine (
assert_reset+ write +deassert_reset) followed by 50ms delay and another reset.Following patch
works_for_me, can be improved to only delay/doublereset when really needed, etc. Andy, could you comment/review?Aleksandr,
Could you provide your Signed-off-by for this patch? I'm going to commit it as is.
Thanks,
AndyQuoted 20 lines
linux/drivers/media/video/cx25840/cx25840-core.c +7
-2@@ -626,7 +642,13 @@if (state->radio) {cx25840_write (client,0x808 ,0xf9 );cx25840_write (client,0x80b ,0x00 ); - } +/* Double reset cx2384x after setting FM radio mode, helps to +avoid "tinny" audio when ivtv I2C bus is being run on +frequency higher than 30 KHz */ +cx25840_and_or (client,0x810 , ~0x01 ,0 ); +msleep (50 ); +cx25840_and_or (client,0x810 , ~0x01 ,1 ); + }else if (std &V4L2_STD_525_60 ) {/* Certain Hauppauge PVR150 models have a hardware bug that causes audio to drop out. For these models the -- Quoted 4 lines
To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html--
To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Quoted 6 lines · Andy Walls
Quoted 5 lines · Mauro Carvalho Chehab
Hi Andy,
This patch has never been applied or nacked. From your last comment, it seems that you're waiting for Aleksandr Signed-of-by:.
Quoted 8 lines
Quoted 2 lines
If this is still the case, I suggest you to wait for a couple days. If he doesn't send it, it is safe to add it without his SOB, since it is really a trivial change.
I'd like to look at this one once more. The extra 50 ms and another reset may be avoidable.
cx25840-core.c:set_input() gets called for
s_frequencyso I'd like not to add 50 ms if not needed.
This patch is ugly, thats why no SOB was provided by me :) Delaying every frequency change by 50 ms is no-go.
One possible solution is to mess with audio controller registers only when its really
required: when standard has to be changed, when TV<->Radio switch occurs, etc.
I have a patch that does something like this, will mail when get to PC with that card and retest it.
As far as I remember there was another codepath that 100% triggers tinny audio, perhaps it was a change of sampling rate.
Quoted 78 lines
Regards,
AndyQuoted 73 lines
Cheers,
Mauro.Quoted 67 lines · Andy Walls
Quoted 23 lines · Aleksandr V. Piskunov
Quoted 8 lines · Aleksandr V. Piskunov
Quoted 2 lines · Aleksandr V. Piskunov
Added FM radio support to Avermedia AVerTV MCE 116 Plus card
What leaves me puzzled, radio only works ok with ivtv newi2c=1
With default newi2c audio is tinny, metallic, with some strange static. Similar problem with pvr-150 was reported years ago, guess issue is still unresolved, perhaps something with cx25840..
This particular "tinny" audio problem is definitely I2C speed related, to be more precise, audio only goes bad if i2c-algo-bit is being run with udelay less than 15, i.e. i2c bus frequency is higher than 30 KHz.
So with default udelay=10 or udelay=5 (optimal for IR reciever on that board) radio goes bad. Running with newi2c=1 is ok, but again it isn't optimal for IR reciever on AVerTV M116.
I2C reads/writes to cx25840 themself are ok, verified using register readback after each write/write4. Problem seems to be that with cx25840 register writes coming too fast on higher i2c bus speed, switching register
0x808_from_ TV standard autodetection mode (0xff) _to_ FM radio mode (0xf9) leaves chip audio detection routine in inconsistent state.Quoted 5 lines
The only solution I found is to do standard routine (
assert_reset+ write +deassert_reset) followed by 50ms delay and another reset.Following patch
works_for_me, can be improved to only delay/doublereset when really needed, etc. Andy, could you comment/review?Aleksandr,
Could you provide your Signed-off-by for this patch? I'm going to commit it as is.
Thanks,
AndyQuoted 20 lines
linux/drivers/media/video/cx25840/cx25840-core.c +7
-2@@ -626,7 +642,13 @@if (state->radio) {cx25840_write (client,0x808 ,0xf9 );cx25840_write (client,0x80b ,0x00 ); - } +/* Double reset cx2384x after setting FM radio mode, helps to +avoid "tinny" audio when ivtv I2C bus is being run on +frequency higher than 30 KHz */ +cx25840_and_or (client,0x810 , ~0x01 ,0 ); +msleep (50 ); +cx25840_and_or (client,0x810 , ~0x01 ,1 ); + }else if (std &V4L2_STD_525_60 ) {/* Certain Hauppauge PVR150 models have a hardware bug that causes audio to drop out. For these models the -- Quoted 4 lines
To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html--
To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html