ixgbe: add support for 82599 based Express Module X520-P2
Subsystems (2)
PATCH 1/2 ixgbe: add support for 82599 based Express Module X520-P2
From: Don Skidmore <[email protected]>
This patch will add the device ID for the 82599-based Ethernet Express Module X520-P2 SFI card.
---
drivers/net/ixgbe/ixgbe_82599.c | 1 + drivers/net/ixgbe/ixgbe_main.c | 2 ++ drivers/net/ixgbe/ixgbe_type.h | 1 + 3 files changed, 4 insertions(+), 0 deletions(-)
drivers/net/ixgbe/ixgbe_82599.c +1 -0
@@ -337,6 +337,7 @@ static enum ixgbe_media_type ixgbe_get_media_type_82599(struct ixgbe_hw *hw) media_type = ixgbe_media_type_backplane;break ;case IXGBE_DEV_ID_82599_SFP : +case IXGBE_DEV_ID_82599_SFP_EM : media_type = ixgbe_media_type_fiber;break ;case IXGBE_DEV_ID_82599_CX4 :
drivers/net/ixgbe/ixgbe_main.c +2 -0
@@ -97,6 +97,8 @@ static struct pci_device_id ixgbe_pci_tbl[] = { board_82599 }, {PCI_VDEVICE (INTEL ,IXGBE_DEV_ID_82599_SFP ), board_82599 }, + {PCI_VDEVICE(INTEL, IXGBE_DEV_ID_82599_SFP_EM), + board_82599 }, {PCI_VDEVICE(INTEL, IXGBE_DEV_ID_82599_KX4_MEZZ), board_82599 }, {PCI_VDEVICE(INTEL, IXGBE_DEV_ID_82599_CX4),
drivers/net/ixgbe/ixgbe_type.h +1 -0
@@ -52,6 +52,7 @@#define IXGBE_DEV_ID_82599_KX4_MEZZ 0x1514#define IXGBE_DEV_ID_82599_CX4 0x10F9#define IXGBE_DEV_ID_82599_SFP 0x10FB +#define IXGBE_DEV_ID_82599_SFP_EM 0x1507#define IXGBE_DEV_ID_82599_XAUI_LOM 0x10FC#define IXGBE_DEV_ID_82599_COMBO_BACKPLANE 0x10F8
PATCH 2/2 ixgbe: Fix KR to KX fail over for Mezzanine cards
From: Don Skidmore <[email protected]>
This patch allows the recently added backplane device IDs that support KR to fail over to KX during link setup. This is accomplished by the new MAC link setup function ixgbe_setup_mac_link_smartspeed(). Comments were also updated to better document the reason for the delays chosen for KX, KX4, BX, BX4 and KR connections.
---
drivers/net/ixgbe/ixgbe_82599.c | 127 ++++++++++++++++++++++++++++++++++++++- drivers/net/ixgbe/ixgbe_type.h | 10 +++ 2 files changed, 134 insertions(+), 3 deletions(-)
drivers/net/ixgbe/ixgbe_82599.c +124 -3
@@ -42,6 +42,10 @@ s32 ixgbe_setup_mac_link_multispeed_fiber(struct ixgbe_hw *hw,ixgbe_link_speed speed, bool autoneg, bool autoneg_wait_to_complete); +static s32 ixgbe_setup_mac_link_smartspeed (struct ixgbe_hw *hw, +ixgbe_link_speed speed, +bool autoneg, +bool autoneg_wait_to_complete);s32 ixgbe_start_mac_link_82599 (struct ixgbe_hw *hw,bool autoneg_wait_to_complete); s32 ixgbe_setup_mac_link_82599(struct ixgbe_hw *hw,
@@ -64,7 +68,13 @@ static void ixgbe_init_mac_link_ops_82599(struct ixgbe_hw *hw)/* Set up dual speed SFP+ support */ mac->ops.setup_link = &ixgbe_setup_mac_link_multispeed_fiber; }else { - mac->ops.setup_link = &ixgbe_setup_mac_link_82599; +if ((mac->ops.get_media_type (hw) == + ixgbe_media_type_backplane) && + (hw->phy.smart_speed == ixgbe_smart_speed_auto || + hw->phy.smart_speed == ixgbe_smart_speed_on)) + mac->ops.setup_link = &ixgbe_setup_mac_link_smartspeed; +else + mac->ops.setup_link = &ixgbe_setup_mac_link_82599; } }
@@ -480,7 +490,12 @@ s32 ixgbe_setup_mac_link_multispeed_fiber(struct ixgbe_hw *hw, hw->mac.autotry_restart = false; } -/* The controller may take up to 500ms at 10g to acquire link */ +/* +* Wait for the controller to acquire link. Per IEEE 802.3ap, +* Section 73.10.2, we may have to wait up to 500ms if KR is +* attempted. 82599 uses the same timing for 10g SFI. +*/ +for (i =0 ; i <5 ; i++) {/* Wait for the link partner to also set speed */ msleep (100 );
@@ -568,6 +583,111 @@ out: }/** +* ixgbe_setup_mac_link_smartspeed - Set MAC link speed using SmartSpeed +* @hw: pointer to hardware structure +* @speed: new link speed +* @autoneg: true if autonegotiation enabled +* @autoneg_wait_to_complete: true when waiting for completion is needed +* +* Implements the Intel SmartSpeed algorithm. +**/ +static s32 ixgbe_setup_mac_link_smartspeed (struct ixgbe_hw *hw, +ixgbe_link_speed speed,bool autoneg, +bool autoneg_wait_to_complete) +{ +s32 status =0 ; +ixgbe_link_speed link_speed; +s32 i, j; +bool link_up = false; +u32 autoc_reg =IXGBE_READ_REG (hw,IXGBE_AUTOC ); + +hw_dbg (hw,"ixgbe_setup_mac_link_smartspeed.\n" ); + +/* Set autoneg_advertised value based on input link speed */ + hw->phy.autoneg_advertised =0 ; + +if (speed &IXGBE_LINK_SPEED_10GB_FULL ) + hw->phy.autoneg_advertised |=IXGBE_LINK_SPEED_10GB_FULL ; + +if (speed &IXGBE_LINK_SPEED_1GB_FULL ) + hw->phy.autoneg_advertised |=IXGBE_LINK_SPEED_1GB_FULL ; + +if (speed &IXGBE_LINK_SPEED_100_FULL ) + hw->phy.autoneg_advertised |=IXGBE_LINK_SPEED_100_FULL ; + +/* +* Implement Intel SmartSpeed algorithm. SmartSpeed will reduce the +* autoneg advertisement if link is unable to be established at the +* highest negotiated rate. This can sometimes happen due to integrity +* issues with the physical media connection. +*/ + +/* First, try to get link with full advertisement */ + hw->phy.smart_speed_active = false; +for (j =0 ; j <IXGBE_SMARTSPEED_MAX_RETRIES ; j++) { + status =ixgbe_setup_mac_link_82599 (hw, speed, autoneg, + autoneg_wait_to_complete); +if (status) + goto out; + +/* +* Wait for the controller to acquire link. Per IEEE 802.3ap, +* Section 73.10.2, we may have to wait up to 500ms if KR is +* attempted, or 200ms if KX/KX4/BX/BX4 is attempted, per +* Table 9 in the AN MAS. +*/ +for (i =0 ; i <5 ; i++) { +mdelay (100 ); + +/* If we have link, just jump out */ + hw->mac.ops.check_link (hw, &link_speed, + &link_up, false); +if (link_up) + goto out; + } + } + +/* +* We didn't get link. If we advertised KR plus one of KX4/KX +* (or BX4/BX), then disable KR and try again. +*/ +if (((autoc_reg &IXGBE_AUTOC_KR_SUPP ) ==0 ) || + ((autoc_reg &IXGBE_AUTOC_KX4_KX_SUPP_MASK ) ==0 )) + goto out; + +/* Turn SmartSpeed on to disable KR support */ + hw->phy.smart_speed_active = true; + status =ixgbe_setup_mac_link_82599 (hw, speed, autoneg, + autoneg_wait_to_complete); +if (status) + goto out; + +/* +* Wait for the controller to acquire link. 600ms will allow for +* the AN link_fail_inhibit_timer as well for multiple cycles of +* parallel detect, both 10g and 1g. This allows for the maximum +* connect attempts as defined in the AN MAS table 73-7. +*/ +for (i =0 ; i <6 ; i++) { +mdelay (100 ); + +/* If we have link, just jump out */ + hw->mac.ops.check_link (hw, &link_speed, + &link_up, false); +if (link_up) + goto out; + } + +/* We didn't get link. Turn SmartSpeed back off. */ + hw->phy.smart_speed_active = false; + status =ixgbe_setup_mac_link_82599 (hw, speed, autoneg, + autoneg_wait_to_complete); + +out: +return status; +} + +/** * ixgbe_check_mac_link_82599 - Determine link and speed status * @hw: pointer to hardware structure * @speed: pointer to link speed
@@ -670,7 +790,8 @@ s32 ixgbe_setup_mac_link_82599(struct ixgbe_hw *hw,if (speed &IXGBE_LINK_SPEED_10GB_FULL )if (orig_autoc &IXGBE_AUTOC_KX4_SUPP ) autoc |=IXGBE_AUTOC_KX4_SUPP ; -if (orig_autoc &IXGBE_AUTOC_KR_SUPP ) +if ((orig_autoc &IXGBE_AUTOC_KR_SUPP ) && + (hw->phy.smart_speed_active == false)) autoc |=IXGBE_AUTOC_KR_SUPP ;if (speed &IXGBE_LINK_SPEED_1GB_FULL ) autoc |=IXGBE_AUTOC_KX_SUPP ;
drivers/net/ixgbe/ixgbe_type.h +10 -0
@@ -2172,6 +2172,14 @@ enum ixgbe_fc_mode {ixgbe_fc_default }; +/* Smart Speed Settings */ +#define IXGBE_SMARTSPEED_MAX_RETRIES 3 +enum ixgbe_smart_speed { + ixgbe_smart_speed_auto =0 , + ixgbe_smart_speed_on, + ixgbe_smart_speed_off +}; +/* PCI bus types */ enum ixgbe_bus_type { ixgbe_bus_type_unknown =0 ,
@@ -2432,6 +2440,8 @@ struct ixgbe_phy_info {enum ixgbe_media_type media_type;bool reset_disable;ixgbe_autoneg_advertised autoneg_advertised; +enum ixgbe_smart_speed smart_speed; +bool smart_speed_active;bool multispeed_fiber; };
Re: [net-next-2.6 PATCH 2/2] ixgbe: Fix KR to KX fail over for Mezzanine cards
From: Jeff Kirsher <[email protected]>
Date: Thu, 08 Oct 2009 18:36:22 -0700
Quoted 10 lines
From: Don Skidmore <[email protected]>
This patch allows the recently added backplane device IDs that support KR to fail over to KX during link setup. This is accomplished by the new MAC link setup function
ixgbe_setup_mac_link_smartspeed(). Comments were also updated to better document the reason for the delays chosen for KX, KX4, BX, BX4 and KR connections.Signed-off-by Don Skidmore <[email protected]>Signed-off-by Jeff Kirsher <[email protected]>
Applied.
From: Jeff Kirsher <[email protected]>
Date: Thu, 08 Oct 2009 18:35:58 -0700
Quoted 8 lines
From: Don Skidmore <[email protected]>
This patch will add the device ID for the 82599-based Ethernet Express Module X520-P2 SFI card.
Signed-off-by Don Skidmore <[email protected]>Signed-off-by Jeff Kirsher <[email protected]>
Applied.