PCI: Use generic cacheline sizing instead of per-vendor tests.
Instead of the PCI code needing to have code to determine the cacheline size of each processor, use the data the cpu identification code should have already determined during early boot.
(The vendor checks are also incomplete, and don't take into account
modern CPUs)
I've been carrying a variant of this code in Fedora for a while, that prints debug information. There are a number of cases where we are currently setting the PCI cacheline size to 32 bytes, when the CPU cacheline size is 64 bytes. With this patch, we set them both the same.
arch/x86/pci/common.c +12 -7
@@ -422,15 +422,20 @@ int __init pcibios_init(void) }/* -* Assume PCI cacheline size of 32 bytes for all x86s except K7/K8 -* and P4. It's also good for 386/486s (which actually have 16) +* Set PCI cacheline size to that of the CPU if the CPU has reported it. +* (For older CPUs that don't support cpuid, we se it to 32 bytes +* It's also good for 386/486s (which actually have 16) * as quite a few PCI devices do not support smaller values. */ - pci_cache_line_size =32 >>2 ; -if (c->x86 >=6 && c->x86_vendor ==X86_VENDOR_AMD ) - pci_cache_line_size =64 >>2 ;/* K7 & K8 */ -else if (c->x86 >6 && c->x86_vendor ==X86_VENDOR_INTEL ) - pci_cache_line_size =128 >>2 ;/* P4 */ + +if (c->x86_clflush_size >0 ) { + pci_cache_line_size = c->x86_clflush_size >>2 ; +printk (KERN_DEBUG "PCI: pci_cache_line_size set to %d bytes\n" , + pci_cache_line_size <<2 ); + }else { + pci_cache_line_size =32 >>2 ; +printk (KERN_DEBUG "PCI: Unknown cacheline size. Setting to 32 bytes\n" ); + }pcibios_resource_survey ();
Quoted 7 lines · On Wed, 14 Oct 2009 16:31:39 -0400 Dave Jones <[email protected]> wrote:
Instead of the PCI code needing to have code to determine the cacheline size of each processor, use the data the cpu identification code should have already determined during early boot.
(The vendor checks are also incomplete, and don't take into account
modern CPUs)
Quoted 8 lines
I've been carrying a variant of this code in Fedora for a while, that prints debug information. There are a number of cases where we are currently setting the PCI cacheline size to 32 bytes, when the CPU cacheline size is 64 bytes. With this patch, we set them both the same.
Signed-off-by Dave Jones <[email protected]>
Does this improve performance enough to warrant putting it into the current cycle? Or is queuing it for 2.6.33 sufficient?
Thanks,
Signature · 1 line
Jesse Barnes, Intel Open Source Technology Center
Quoted 16 lines · Jesse Barnes
Quoted 13 lines · On Wed, 14 Oct 2009 16:31:39 -0400 Dave Jones <[email protected]> wrote:
Instead of the PCI code needing to have code to determine the cacheline size of each processor, use the data the cpu identification code should have already determined during early boot.
(The vendor checks are also incomplete, and don't take into account
modern CPUs)I've been carrying a variant of this code in Fedora for a while, that prints debug information. There are a number of cases where we are currently setting the PCI cacheline size to 32 bytes, when the CPU cacheline size is 64 bytes. With this patch, we set them both the same.
Quoted 5 lines
Quoted 2 lines
Signed-off-by Dave Jones <[email protected]>Does this improve performance enough to warrant putting it into the current cycle? Or is queuing it for 2.6.33 sufficient?
I haven't done any performance testing with/without. My intentions were purely from a correctness standpoint.
It's not critical, and we've lived with this bug for a long time, so waiting is fine.
Dave
Quoted 4 lines · Dave Jones
I've been carrying a variant of this code in Fedora for a while, that prints debug information. There are a number of cases where we are currently setting the PCI cacheline size to 32 bytes, when the CPU cacheline size is 64 bytes. With this patch, we set them both the same.
In case anyone is curious, here's the version we carried in Fedora for a while..
Dave
arch/x86/pci/common.c +16 -0
@@ -432,6 +432,22 @@ int __init pcibios_init(void)else if (c->x86 >6 && c->x86_vendor ==X86_VENDOR_INTEL ) pci_cache_line_size =128 >>2 ;/* P4 */ +if (c->x86_clflush_size != (pci_cache_line_size <<2 )) +printk (KERN_DEBUG "PCI: old code would have set cacheline " +"size to %d bytes, but clflush_size = %d\n" , + pci_cache_line_size <<2 , + c->x86_clflush_size); + +/* Once we know this logic works, all the above code can be deleted. */ +if (c->x86_clflush_size >0 ) { + pci_cache_line_size = c->x86_clflush_size >>2 ; +printk (KERN_DEBUG "PCI: pci_cache_line_size set to %d bytes\n" , + pci_cache_line_size <<2 ); + }else { + pci_cache_line_size =32 >>2 ; +printk (KERN_DEBUG "PCI: Unknown cacheline size. Setting to 32 bytes\n" ); + } +pcibios_resource_survey ();if (pci_bf_sort >= pci_force_bf)
Jesse Barnes
AppliedQuoted 7 lines · On Wed, 14 Oct 2009 16:31:39 -0400 Dave Jones <[email protected]> wrote:
Instead of the PCI code needing to have code to determine the cacheline size of each processor, use the data the cpu identification code should have already determined during early boot.
(The vendor checks are also incomplete, and don't take into account
modern CPUs)
Quoted 7 lines
I've been carrying a variant of this code in Fedora for a while, that prints debug information. There are a number of cases where we are currently setting the PCI cacheline size to 32 bytes, when the CPU cacheline size is 64 bytes. With this patch, we set them both the same.
Signed-off-by Dave Jones <[email protected]>
Applied this; had to fix up a few conflicts due to Tejun's recent CLS improvements though...
Signature · 1 line
Jesse Barnes, Intel Open Source Technology Center