iwmc3200wifi: add BGN sdio device id
A message that is not in the archive (sent off-list or not yet received): [email protected]
PATCH 1/16 iwmc3200wifi: add BGN sdio device id
Add BGN SKU sdio device id.
--- drivers/net/wireless/iwmc3200wifi/sdio.c | 6 ++++-- 1 files changed, 4 insertions(+), 2 deletions(-)
drivers/net/wireless/iwmc3200wifi/sdio.c +4 -2
@@ -493,8 +493,10 @@ static void iwm_sdio_remove(struct sdio_func *func) }static const struct sdio_device_id iwm_sdio_ids[] = { - {SDIO_DEVICE (SDIO_VENDOR_ID_INTEL , -SDIO_DEVICE_ID_INTEL_IWMC3200WIFI ) }, +/* Global/AGN SKU */ + {SDIO_DEVICE (SDIO_VENDOR_ID_INTEL ,0x1403 ) }, +/* BGN SKU */ + {SDIO_DEVICE (SDIO_VENDOR_ID_INTEL ,0x1408 ) }, {/* end: all zeroes */ }, };MODULE_DEVICE_TABLE (sdio, iwm_sdio_ids);
Signature · 1 line
1.6.0.4
PATCH 2/16 iwmc3200wifi: allow joining an existed IBSS network
We used to only support creating a new IBSS network. Now joining to an existed IBSS network is supported as well.
--- drivers/net/wireless/iwmc3200wifi/cfg80211.c | 22 ++-------------------- 1 files changed, 2 insertions(+), 20 deletions(-)
drivers/net/wireless/iwmc3200wifi/cfg80211.c +2 -20
@@ -405,39 +405,21 @@ static int iwm_cfg80211_join_ibss(struct wiphy *wiphy, struct net_device *dev, {struct iwm_priv *iwm =wiphy_to_iwm (wiphy);struct ieee80211_channel *chan = params->channel; -struct cfg80211_bss *bss;if (!test_bit (IWM_STATUS_READY , &iwm->status))return -EIO ; -/* UMAC doesn't support creating IBSS network with specified bssid. -* This should be removed after we have join only mode supported. */ +/* UMAC doesn't support creating or joining an IBSS network +* with specified bssid. */ if (params->bssid)return -EOPNOTSUPP ; - bss =cfg80211_get_ibss (iwm_to_wiphy (iwm),NULL , - params->ssid, params->ssid_len); -if (!bss) { -iwm_scan_one_ssid (iwm, params->ssid, params->ssid_len); -schedule_timeout_interruptible (2 *HZ ); - bss =cfg80211_get_ibss (iwm_to_wiphy (iwm),NULL , - params->ssid, params->ssid_len); - } -/* IBSS join only mode is not supported by UMAC ATM */ -if (bss) { -cfg80211_put_bss (bss); -return -EOPNOTSUPP ; - } - iwm->channel =ieee80211_frequency_to_channel (chan->center_freq); iwm->umac_profile->ibss.band = chan->band; iwm->umac_profile->ibss.channel = iwm->channel; iwm->umac_profile->ssid.ssid_len = params->ssid_len;memcpy (iwm->umac_profile->ssid.ssid, params->ssid, params->ssid_len); -if (params->bssid) -memcpy (&iwm->umac_profile->bssid[0 ], params->bssid,ETH_ALEN ); -return iwm_send_mlme_profile (iwm); }
Signature · 1 line
1.6.0.4
PATCH 3/16 iwmc3200wifi: WPS support
From: Samuel Ortiz <[email protected]>
By setting the WSC profile flag, we now support WPS as an enrollee.
--- drivers/net/wireless/iwmc3200wifi/cfg80211.c | 7 +++++++ drivers/net/wireless/iwmc3200wifi/commands.h | 3 +++ 2 files changed, 10 insertions(+), 0 deletions(-)
drivers/net/wireless/iwmc3200wifi/cfg80211.c +7 -0
@@ -628,6 +628,13 @@ static int iwm_cfg80211_connect(struct wiphy *wiphy, struct net_device *dev, iwm->default_key = sme->key_idx; } +/* WPA and open AUTH type from wpa_s means WPS (a.k.a. WSC) */ +if ((iwm->umac_profile->sec.flags & + (UMAC_SEC_FLG_WPA_ON_MSK |UMAC_SEC_FLG_RSNA_ON_MSK )) && + iwm->umac_profile->sec.auth_type ==UMAC_AUTH_TYPE_OPEN ) { + iwm->umac_profile->sec.flags =UMAC_SEC_FLG_WSC_ON_MSK ; + } + ret =iwm_send_mlme_profile (iwm); if (iwm->umac_profile->sec.auth_type != UMAC_AUTH_TYPE_LEGACY_PSK ||
drivers/net/wireless/iwmc3200wifi/commands.h +3 -0
@@ -288,6 +288,9 @@ struct iwm_umac_cmd_scan_request {/* iwm_umac_security.flag is WSC mode on -- bits [2:2] */ #define UMAC_SEC_FLG_WSC_ON_POS 2#define UMAC_SEC_FLG_WSC_ON_SEED 1 +#define UMAC_SEC_FLG_WSC_ON_MSK (UMAC_SEC_FLG_WSC_ON_SEED << \ + UMAC_SEC_FLG_WSC_ON_POS) +/* Legacy profile can use only WEP40 and WEP104 for encryption and * OPEN or PSK for authentication */
Signature · 1 line
1.6.0.4
PATCH 4/16 iwmc3200wifi: CT kill support
From: Samuel Ortiz <[email protected]>
We set the initial CT (Temperature control) value to 110 degrees. If the chip goes over that threshold, we hard block the device which will turn it down. At the same time we schedule a 30 seconds delayed work that unblock the device (and userspace is supposed to bring it back up), hoping that the chip will have cooled down by then...
--- drivers/net/wireless/iwmc3200wifi/commands.c | 11 +++++++++++ drivers/net/wireless/iwmc3200wifi/commands.h | 1 + drivers/net/wireless/iwmc3200wifi/fw.c | 2 ++ drivers/net/wireless/iwmc3200wifi/iwm.h | 3 +++ drivers/net/wireless/iwmc3200wifi/lmac.h | 8 ++++++++ drivers/net/wireless/iwmc3200wifi/main.c | 14 ++++++++++++++ drivers/net/wireless/iwmc3200wifi/netdev.c | 1 + drivers/net/wireless/iwmc3200wifi/rx.c | 16 +++++++++++++++- 8 files changed, 55 insertions(+), 1 deletions(-)
drivers/net/wireless/iwmc3200wifi/commands.c +11 -0
@@ -275,6 +275,17 @@ int iwm_send_calib_results(struct iwm_priv *iwm)return ret; } +int iwm_send_ct_kill_cfg (struct iwm_priv *iwm,u8 entry,u8 exit) +{ +struct iwm_ct_kill_cfg_cmd cmd; + + cmd.entry_threshold = entry; + cmd.exit_threshold = exit; + +return iwm_send_lmac_ptrough_cmd (iwm,REPLY_CT_KILL_CONFIG_CMD , &cmd, +sizeof (struct iwm_ct_kill_cfg_cmd ),0 ); +} +int iwm_send_umac_reset (struct iwm_priv *iwm,__le32 reset_flags,bool resp) {struct iwm_udma_wifi_cmd udma_cmd =UDMA_UMAC_INIT ;
drivers/net/wireless/iwmc3200wifi/commands.h +1 -0
@@ -396,6 +396,7 @@ int iwm_send_init_calib_cfg(struct iwm_priv *iwm, u8 calib_requested);int iwm_send_periodic_calib_cfg (struct iwm_priv *iwm,u8 calib_requested);int iwm_send_calib_results (struct iwm_priv *iwm);int iwm_store_rxiq_calib_result (struct iwm_priv *iwm); +int iwm_send_ct_kill_cfg (struct iwm_priv *iwm,u8 entry,u8 exit);/* UMAC commands */ int iwm_send_wifi_if_cmd(struct iwm_priv *iwm, void *payload, u16 payload_size,
drivers/net/wireless/iwmc3200wifi/fw.c +2 -0
@@ -398,6 +398,8 @@ int iwm_load_fw(struct iwm_priv *iwm)iwm_send_prio_table (iwm);iwm_send_calib_results (iwm);iwm_send_periodic_calib_cfg (iwm, periodic_calib_map); +iwm_send_ct_kill_cfg (iwm, iwm->conf.ct_kill_entry, + iwm->conf.ct_kill_exit);return 0 ;
drivers/net/wireless/iwmc3200wifi/iwm.h +3 -0
@@ -65,6 +65,8 @@ struct iwm_conf {u32 sdio_ior_timeout;unsigned long calib_map;unsigned long expected_calib_map; +u8 ct_kill_entry; +u8 ct_kill_exit;bool reset_on_fatal_err;bool auto_connect;bool wimax_not_present;
@@ -276,6 +278,7 @@ struct iwm_priv {struct iw_statistics wstats;struct delayed_work stats_request;struct delayed_work disconnect; +struct delayed_work ct_kill_delay;struct iwm_debugfs dbg;
drivers/net/wireless/iwmc3200wifi/lmac.h +8 -0
@@ -187,6 +187,14 @@ struct iwm_coex_prio_table_cmd { COEX_EVT_FLAG_MEDIUM_ACTV_NTFY_MSK | \ COEX_EVT_FLAG_DELAY_MEDIUM_FREE_NTFY_MSK) +/* CT kill config command */ +struct iwm_ct_kill_cfg_cmd { +u32 exit_threshold; +u32 reserved; +u32 entry_threshold; +} __attribute__ ((packed)); + +/* LMAC OP CODES */ #define REPLY_PAD 0x0#define REPLY_ALIVE 0x1
drivers/net/wireless/iwmc3200wifi/main.c +14 -0
@@ -64,6 +64,8 @@ static struct iwm_conf def_iwm_conf = {BIT (PHY_CALIBRATE_TX_IQ_CMD ) |BIT (PHY_CALIBRATE_RX_IQ_CMD ) | BIT(SHILOH_PHY_CALIBRATE_BASE_BAND_CMD), + .ct_kill_entry = 110, + .ct_kill_exit = 110, .reset_on_fatal_err = 1, .auto_connect = 1, .wimax_not_present = 0,
@@ -134,6 +136,17 @@ static void iwm_disconnect_work(struct work_struct *work)cfg80211_disconnected (iwm_to_ndev (iwm),0 ,NULL ,0 ,GFP_KERNEL ); } +static void iwm_ct_kill_work (struct work_struct *work) +{ +struct iwm_priv *iwm = + container_of(work, struct iwm_priv, ct_kill_delay.work); +struct wiphy *wiphy =iwm_to_wiphy (iwm); + +IWM_INFO (iwm,"CT kill delay timeout\n" ); + +wiphy_rfkill_set_hw_state (wiphy, false); +} +static int __iwm_up (struct iwm_priv *iwm);static int __iwm_down (struct iwm_priv *iwm);
@@ -226,6 +239,7 @@ int iwm_priv_init(struct iwm_priv *iwm) iwm->scan_id =1 ;INIT_DELAYED_WORK (&iwm->stats_request, iwm_statistics_request);INIT_DELAYED_WORK (&iwm->disconnect, iwm_disconnect_work); +INIT_DELAYED_WORK (&iwm->ct_kill_delay, iwm_ct_kill_work);INIT_WORK (&iwm->reset_worker, iwm_reset_worker);INIT_LIST_HEAD (&iwm->bss_list);
drivers/net/wireless/iwmc3200wifi/netdev.c +1 -0
@@ -152,6 +152,7 @@ void iwm_if_free(struct iwm_priv *iwm)if (!iwm_to_ndev (iwm))return ; +cancel_delayed_work_sync (&iwm->ct_kill_delay);free_netdev (iwm_to_ndev (iwm));iwm_priv_deinit (iwm);kfree (iwm->umac_profile);
drivers/net/wireless/iwmc3200wifi/rx.c +15 -1
@@ -1079,6 +1079,7 @@ static int iwm_ntf_wifi_if_wrapper(struct iwm_priv *iwm, u8 *buf,return 0 ; } +#define CT_KILL_DELAY (30 * HZ)static int iwm_ntf_card_state (struct iwm_priv *iwm,u8 *buf,unsigned long buf_size,struct iwm_wifi_cmd *cmd) {
@@ -1091,7 +1092,20 @@ static int iwm_ntf_card_state(struct iwm_priv *iwm, u8 *buf, flags &IWM_CARD_STATE_HW_DISABLED ?"ON" :"OFF" , flags & IWM_CARD_STATE_CTKILL_DISABLED ? "ON" : "OFF"); -wiphy_rfkill_set_hw_state (wiphy, flags &IWM_CARD_STATE_HW_DISABLED ); +if (flags &IWM_CARD_STATE_CTKILL_DISABLED ) { +/* +* We got a CTKILL event: We bring the interface down in +* oder to cool the device down, and try to bring it up +* 30 seconds later. If it's still too hot, we'll go through +* this code path again. +*/ +cancel_delayed_work_sync (&iwm->ct_kill_delay); +schedule_delayed_work (&iwm->ct_kill_delay,CT_KILL_DELAY ); + } + +wiphy_rfkill_set_hw_state (wiphy, flags & + (IWM_CARD_STATE_HW_DISABLED | +IWM_CARD_STATE_CTKILL_DISABLED ));return 0 ; }
Signature · 1 line
1.6.0.4
PATCH 5/16 iwmc3200wifi: Profile flags can be WPA1 or WPA2 not both
From: Samuel Ortiz <[email protected]>
UMAC will ASSERT if the profile security flag is WPA1 | WPA2, so we can only accept one of those.
Moreover wpa_s wext and nl80211 drivers dont try to send WPA1 | WPA2, but only one at a time.
--- drivers/net/wireless/iwmc3200wifi/cfg80211.c | 6 +++--- 1 files changed, 3 insertions(+), 3 deletions(-)
drivers/net/wireless/iwmc3200wifi/cfg80211.c +3 -3
@@ -472,12 +472,12 @@ static int iwm_set_wpa_version(struct iwm_priv *iwm, u32 wpa_version)return 0 ; } +if (wpa_version &NL80211_WPA_VERSION_1 ) + iwm->umac_profile->sec.flags =UMAC_SEC_FLG_WPA_ON_MSK ; +if (wpa_version &NL80211_WPA_VERSION_2 ) iwm->umac_profile->sec.flags =UMAC_SEC_FLG_RSNA_ON_MSK ; -if (wpa_version &NL80211_WPA_VERSION_1 ) - iwm->umac_profile->sec.flags |=UMAC_SEC_FLG_WPA_ON_MSK ; -return 0 ; }
Signature · 1 line
1.6.0.4
PATCH 6/16 iwmc3200wifi: Improve rx debug
From: Samuel Ortiz <[email protected]>
We display the correct DROP/RELEASE string for each rx packets, and when it's dropped we also display the reason.
--- drivers/net/wireless/iwmc3200wifi/rx.c | 7 +++++-- 1 files changed, 5 insertions(+), 2 deletions(-)
drivers/net/wireless/iwmc3200wifi/rx.c +5 -2
@@ -423,7 +423,9 @@ static int iwm_ntf_rx_ticket(struct iwm_priv *iwm, u8 *buf,if (IS_ERR (ticket_node))return PTR_ERR (ticket_node); -IWM_DBG_RX (iwm,DBG ,"TICKET RELEASE(%d)\n" , +IWM_DBG_RX (iwm,DBG ,"TICKET %s(%d)\n" , + ticket->action ==IWM_RX_TICKET_RELEASE ? +"RELEASE" :"DROP" , ticket->id);list_add_tail (&ticket_node->node, &iwm->rx_tickets);
@@ -1458,7 +1460,8 @@ static void iwm_rx_process_packet(struct iwm_priv *iwm, }break ;case IWM_RX_TICKET_DROP : -IWM_DBG_RX (iwm,DBG ,"DROP packet\n" ); +IWM_DBG_RX (iwm,DBG ,"DROP packet: 0x%x\n" , +le16_to_cpu (ticket_node->ticket->flags));kfree_skb (packet->skb);break ;default :
Signature · 1 line
1.6.0.4
PATCH 7/16 iwmc3200wifi: Update statistics notification structure
From: Samuel Ortiz <[email protected]>
The latest firmware adds a ht_rates and a chain_energy field. The latter is needed as we want to eventually support RSSI/antenna handling.
--- drivers/net/wireless/iwmc3200wifi/umac.h | 5 +++++ 1 files changed, 5 insertions(+), 0 deletions(-)
drivers/net/wireless/iwmc3200wifi/umac.h +5 -0
@@ -687,6 +687,9 @@ struct iwm_umac_notif_rx_ticket {/* Tx/Rx rates window (number of max of last update window per second) */ #define UMAC_NTF_RATE_SAMPLE_NR 4 +/* Max numbers of bits required to go through all antennae in bitmasks */ +#define UMAC_PHY_NUM_CHAINS 3 +#define IWM_UMAC_MGMT_TID 8#define IWM_UMAC_TID_NR 8
@@ -697,9 +700,11 @@ struct iwm_umac_notif_stats {__le16 tid_load[IWM_UMAC_TID_NR +2 ];/* 1 non-QoS + 1 dword align */ __le16 tx_rate[UMAC_NTF_RATE_SAMPLE_NR ];__le16 rx_rate[UMAC_NTF_RATE_SAMPLE_NR ]; +__le32 chain_energy[UMAC_PHY_NUM_CHAINS ];s32 rssi_dbm;s32 noise_dbm;__le32 supp_rates; +__le32 supp_ht_rates;__le32 missed_beacons;__le32 rx_beacons;__le32 rx_dir_pkts;
Signature · 1 line
1.6.0.4
PATCH 8/16 iwmc3200wifi: Update fixed size config definitions
From: Samuel Ortiz <[email protected]>
We need to be in sync with the latest firmware API.
--- drivers/net/wireless/iwmc3200wifi/commands.h | 60 +++++++++++++++++++++++++- 1 files changed, 58 insertions(+), 2 deletions(-)
drivers/net/wireless/iwmc3200wifi/commands.h +58 -2
@@ -102,7 +102,6 @@ enum {CFG_SCAN_NUM_PASSIVE_CHAN_PER_PARTIAL_SCAN ,CFG_TLC_SUPPORTED_TX_HT_RATES ,CFG_TLC_SUPPORTED_TX_RATES , -CFG_TLC_VALID_ANTENNA ,CFG_TLC_SPATIAL_STREAM_SUPPORTED ,CFG_TLC_RETRY_PER_RATE , CFG_TLC_RETRY_PER_HT_RATE,
@@ -136,6 +135,10 @@ enum {CFG_TLC_RENEW_ADDBA_DELAY ,CFG_TLC_NUM_OF_MULTISEC_TO_COUN_LOAD ,CFG_TLC_IS_STABLE_IN_HT , +CFG_TLC_SR_SIC_1ST_FAIL , +CFG_TLC_SR_SIC_1ST_PASS , +CFG_TLC_SR_SIC_TOTAL_FAIL , +CFG_TLC_SR_SIC_TOTAL_PASS ,CFG_RLC_CHAIN_CTRL ,CFG_TRK_TABLE_OP_MODE , CFG_TRK_TABLE_RSSI_THRESHOLD,
@@ -147,6 +150,58 @@ enum {CFG_MLME_DBG_NOTIF_BLOCK ,CFG_BT_OFF_BECONS_INTERVALS ,CFG_BT_FRAG_DURATION , +CFG_ACTIVE_CHAINS , +CFG_CALIB_CTRL , +CFG_CAPABILITY_SUPPORTED_HT_RATES , +CFG_HT_MAC_PARAM_INFO , +CFG_MIMO_PS_MODE , +CFG_HT_DEFAULT_CAPABILIES_INFO , +CFG_LED_SC_RESOLUTION_FACTOR , +CFG_PTAM_ENERGY_CCK_DET_DEFAULT , +CFG_PTAM_CORR40_4_TH_ADD_MIN_MRC_DEFAULT , +CFG_PTAM_CORR40_4_TH_ADD_MIN_DEFAULT , +CFG_PTAM_CORR32_4_TH_ADD_MIN_MRC_DEFAULT , +CFG_PTAM_CORR32_4_TH_ADD_MIN_DEFAULT , +CFG_PTAM_CORR32_1_TH_ADD_MIN_MRC_DEFAULT , +CFG_PTAM_CORR32_1_TH_ADD_MIN_DEFAULT , +CFG_PTAM_ENERGY_CCK_DET_MIN_VAL , +CFG_PTAM_CORR40_4_TH_ADD_MIN_MRC_MIN_VAL , +CFG_PTAM_CORR40_4_TH_ADD_MIN_MIN_VAL , +CFG_PTAM_CORR32_4_TH_ADD_MIN_MRC_MIN_VAL , +CFG_PTAM_CORR32_4_TH_ADD_MIN_MIN_VAL , +CFG_PTAM_CORR32_1_TH_ADD_MIN_MRC_MIN_VAL , +CFG_PTAM_CORR32_1_TH_ADD_MIN_MIN_VAL , +CFG_PTAM_ENERGY_CCK_DET_MAX_VAL , +CFG_PTAM_CORR40_4_TH_ADD_MIN_MRC_MAX_VAL , +CFG_PTAM_CORR40_4_TH_ADD_MIN_MAX_VAL , +CFG_PTAM_CORR32_4_TH_ADD_MIN_MRC_MAX_VAL , +CFG_PTAM_CORR32_4_TH_ADD_MIN_MAX_VAL , +CFG_PTAM_CORR32_1_TH_ADD_MIN_MRC_MAX_VAL , +CFG_PTAM_CORR32_1_TH_ADD_MIN_MAX_VAL , +CFG_PTAM_ENERGY_CCK_DET_STEP_VAL , +CFG_PTAM_CORR40_4_TH_ADD_MIN_MRC_STEP_VAL , +CFG_PTAM_CORR40_4_TH_ADD_MIN_STEP_VAL , +CFG_PTAM_CORR32_4_TH_ADD_MIN_MRC_STEP_VAL , +CFG_PTAM_CORR32_4_TH_ADD_MIN_STEP_VAL , +CFG_PTAM_CORR32_1_TH_ADD_MIN_MRC_STEP_VAL , +CFG_PTAM_CORR32_1_TH_ADD_MIN_STEP_VAL , +CFG_PTAM_LINK_SENS_FA_OFDM_MAX , +CFG_PTAM_LINK_SENS_FA_OFDM_MIN , +CFG_PTAM_LINK_SENS_FA_CCK_MAX , +CFG_PTAM_LINK_SENS_FA_CCK_MIN , +CFG_PTAM_LINK_SENS_NRG_DIFF , +CFG_PTAM_LINK_SENS_NRG_MARGIN , +CFG_PTAM_LINK_SENS_MAX_NUMBER_OF_TIMES_IN_CCK_NO_FA , +CFG_PTAM_LINK_SENS_AUTO_CORR_MAX_TH_CCK , +CFG_AGG_MGG_TID_LOAD_ADDBA_THRESHOLD , +CFG_AGG_MGG_TID_LOAD_DELBA_THRESHOLD , +CFG_AGG_MGG_ADDBA_BUF_SIZE , +CFG_AGG_MGG_ADDBA_INACTIVE_TIMEOUT , +CFG_AGG_MGG_ADDBA_DEBUG_FLAGS , +CFG_SCAN_PERIODIC_RSSI_HIGH_THRESHOLD , +CFG_SCAN_PERIODIC_COEF_RSSI_HIGH , +CFG_11D_ENABLED , +CFG_11H_FEATURE_FLAGS ,/* <-- LAST --> */ CFG_TBL_FIX_LAST
@@ -155,7 +210,8 @@ enum {/* variable size table */ enum {CFG_NET_ADDR =0 , -CFG_PROFILE , +CFG_LED_PATTERN_TABLE , +/* <-- LAST --> */ CFG_TBL_VAR_LAST };
Signature · 1 line
1.6.0.4
PATCH 9/16 iwmc3200wifi: Tx power setting
From: Samuel Ortiz <[email protected]>
We can now set the Tx power from e.g. iwconfig.
--- drivers/net/wireless/iwmc3200wifi/cfg80211.c | 12 +++++++++++- drivers/net/wireless/iwmc3200wifi/commands.c | 13 +++++++++++++ drivers/net/wireless/iwmc3200wifi/commands.h | 6 ++++++ 3 files changed, 30 insertions(+), 1 deletions(-)
drivers/net/wireless/iwmc3200wifi/cfg80211.c +11 -1
@@ -671,9 +671,19 @@ static int iwm_cfg80211_disconnect(struct wiphy *wiphy, struct net_device *dev,static int iwm_cfg80211_set_txpower (struct wiphy *wiphy,enum tx_power_setting type,int dbm) { +struct iwm_priv *iwm =wiphy_to_iwm (wiphy); +int ret; +switch (type) {case TX_POWER_AUTOMATIC :return 0 ; +case TX_POWER_FIXED : + ret =iwm_umac_set_config_fix (iwm,UMAC_PARAM_TBL_CFG_FIX , +CFG_TX_PWR_LIMIT_USR , dbm *2 ); +if (ret <0 ) +return ret; + +return iwm_tx_power_trigger (iwm);default :return -EOPNOTSUPP ; }
@@ -685,7 +695,7 @@ static int iwm_cfg80211_get_txpower(struct wiphy *wiphy, int *dbm) {struct iwm_priv *iwm =wiphy_to_iwm (wiphy); - *dbm = iwm->txpower; + *dbm = iwm->txpower >>1 ;return 0 ; }
drivers/net/wireless/iwmc3200wifi/commands.c +13 -0
@@ -794,6 +794,19 @@ int iwm_invalidate_mlme_profile(struct iwm_priv *iwm)return ret ?0 : -EBUSY ; } +int iwm_tx_power_trigger (struct iwm_priv *iwm) +{ +struct iwm_umac_pwr_trigger pwr_trigger; + + pwr_trigger.hdr.oid =UMAC_WIFI_IF_CMD_TX_PWR_TRIGGER ; + pwr_trigger.hdr.buf_size = +cpu_to_le16 (sizeof (struct iwm_umac_pwr_trigger ) - +sizeof (struct iwm_umac_wifi_if )); + + +return iwm_send_wifi_if_cmd (iwm, &pwr_trigger,sizeof (pwr_trigger),1 ); +} +int iwm_send_umac_stats_req (struct iwm_priv *iwm,u32 flags) {struct iwm_udma_wifi_cmd udma_cmd =UDMA_UMAC_INIT ;
drivers/net/wireless/iwmc3200wifi/commands.h +6 -0
@@ -441,6 +441,11 @@ struct iwm_umac_tx_key_id {u8 reserved[3 ]; } __attribute__ ((packed)); +struct iwm_umac_pwr_trigger { +struct iwm_umac_wifi_if hdr; +__le32 reseved; +} __attribute__ ((packed)); +struct iwm_umac_cmd_stats_req {__le32 flags; } __attribute__ ((packed));
@@ -467,6 +472,7 @@ int iwm_invalidate_mlme_profile(struct iwm_priv *iwm);int iwm_send_packet (struct iwm_priv *iwm,struct sk_buff *skb,int pool_id);int iwm_set_tx_key (struct iwm_priv *iwm,u8 key_idx);int iwm_set_key (struct iwm_priv *iwm,bool remove,struct iwm_key *key); +int iwm_tx_power_trigger (struct iwm_priv *iwm);int iwm_send_umac_stats_req (struct iwm_priv *iwm,u32 flags);int iwm_send_umac_channel_list (struct iwm_priv *iwm); int iwm_scan_ssids(struct iwm_priv *iwm, struct cfg80211_ssid *ssids,
Signature · 1 line
1.6.0.4
PATCH 10/16 iwmc3200wifi: SDIO disable race fix
From: Samuel Ortiz <[email protected]>
When calling sdio->bus_disable(), we are flushing the command lists before disabling the sdio function. We can thus potentially get a command response after having flushed the command list.
To avoid that race, we have to call iwm_reset() after disabling the sdio function.
--- drivers/net/wireless/iwmc3200wifi/sdio.c | 4 ++-- 1 files changed, 2 insertions(+), 2 deletions(-)
drivers/net/wireless/iwmc3200wifi/sdio.c +2 -2
@@ -224,8 +224,6 @@ static int if_sdio_disable(struct iwm_priv *iwm)struct iwm_sdio_priv *hw =iwm_to_if_sdio (iwm);int ret; -iwm_reset (iwm); -sdio_claim_host (hw->func);sdio_writeb (hw->func,0 ,IWM_SDIO_INTR_ENABLE_ADDR , &ret);if (ret <0 )
@@ -237,6 +235,8 @@ static int if_sdio_disable(struct iwm_priv *iwm)iwm_sdio_rx_free (hw); +iwm_reset (iwm); +IWM_DBG_SDIO (iwm,INFO ,"IWM SDIO disable\n" );return 0 ;
Signature · 1 line
1.6.0.4
PATCH 11/16 iwmc3200wifi: Check for cmd pointer before dereferencing it
From: Samuel Ortiz <[email protected]>
The wifi_if_wrapper notification handling code uses a cmd pointer without checking if it's valid or not. We're dereferencing it because we assume that we only get to that point if there was a pending command for us. That's not always true, so we'd better check.
--- drivers/net/wireless/iwmc3200wifi/rx.c | 10 ++++++++-- 1 files changed, 8 insertions(+), 2 deletions(-)
drivers/net/wireless/iwmc3200wifi/rx.c +8 -2
@@ -1058,8 +1058,14 @@ static int iwm_ntf_wifi_if_wrapper(struct iwm_priv *iwm, u8 *buf,unsigned long buf_size, struct iwm_wifi_cmd *cmd) { - struct iwm_umac_wifi_if *hdr = - (struct iwm_umac_wifi_if *)cmd->buf.payload; + struct iwm_umac_wifi_if *hdr; + +if (cmd ==NULL ) { +IWM_ERR (iwm,"Couldn't find expected wifi command\n" ); +return -EINVAL ; + } + + hdr = (struct iwm_umac_wifi_if *)cmd->buf.payload;IWM_DBG_NTF (iwm,DBG ,"WIFI_IF_WRAPPER cmd is delivered to UMAC: " "oid is 0x%x\n" , hdr->oid);
Signature · 1 line
1.6.0.4
PATCH 12/16 iwmc3200wifi: Do not handle wifi command if the interface is not ready
From: Samuel Ortiz <[email protected]>
When resetting or bringing the interface down, we should just reject any wifi related command.
--- drivers/net/wireless/iwmc3200wifi/commands.c | 5 +++++ 1 files changed, 5 insertions(+), 0 deletions(-)
drivers/net/wireless/iwmc3200wifi/commands.c +5 -0
@@ -77,6 +77,11 @@ int iwm_send_wifi_if_cmd(struct iwm_priv *iwm, void *payload, u16 payload_size,int ret;u8 oid = hdr->oid; +if (!test_bit (IWM_STATUS_READY , &iwm->status)) { +IWM_ERR (iwm,"Interface is not ready yet" ); +return -EAGAIN ; + } + umac_cmd.id =UMAC_CMD_OPCODE_WIFI_IF_WRAPPER ; umac_cmd.resp = resp;
Signature · 1 line
1.6.0.4
PATCH 13/16 iwmc3200wifi: Try shared auth when open WEP fails
From: Samuel Ortiz <[email protected]>
When we fail to associate with an open WEP AP, we fall back to shared auth. This allows us to support joining a shared auth WEP AP with iwconfig.
--- drivers/net/wireless/iwmc3200wifi/commands.c | 2 +- drivers/net/wireless/iwmc3200wifi/iwm.h | 1 + drivers/net/wireless/iwmc3200wifi/main.c | 28 ++++++++++++++++++++++++++ drivers/net/wireless/iwmc3200wifi/rx.c | 28 +++++++++++++++++++++---- 4 files changed, 53 insertions(+), 6 deletions(-)
drivers/net/wireless/iwmc3200wifi/commands.c +1 -1
@@ -794,7 +794,7 @@ int iwm_invalidate_mlme_profile(struct iwm_priv *iwm)return ret; ret =wait_event_interruptible_timeout (iwm->mlme_queue, - (iwm->umac_profile_active ==0 ),2 *HZ ); + (iwm->umac_profile_active ==0 ),5 *HZ );return ret ?0 : -EBUSY ; }
drivers/net/wireless/iwmc3200wifi/iwm.h +1 -0
@@ -285,6 +285,7 @@ struct iwm_priv {u8 *eeprom;struct timer_list watchdog;struct work_struct reset_worker; +struct work_struct auth_retry_worker;struct mutex mutex;u8 *req_ie;
drivers/net/wireless/iwmc3200wifi/main.c +28 -0
@@ -208,6 +208,33 @@ static void iwm_reset_worker(struct work_struct *work)mutex_unlock (&iwm->mutex); } +static void iwm_auth_retry_worker (struct work_struct *work) +{ +struct iwm_priv *iwm; +int i, ret; + + iwm = container_of(work, struct iwm_priv, auth_retry_worker); +if (iwm->umac_profile_active) { + ret =iwm_invalidate_mlme_profile (iwm); +if (ret <0 ) +return ; + } + + iwm->umac_profile->sec.auth_type =UMAC_AUTH_TYPE_LEGACY_PSK ; + + ret =iwm_send_mlme_profile (iwm); +if (ret <0 ) +return ; + +for (i =0 ; i <IWM_NUM_KEYS ; i++) +if (iwm->keys[i].key_len) +iwm_set_key (iwm,0 , &iwm->keys[i]); + +iwm_set_tx_key (iwm, iwm->default_key); +} + + +static void iwm_watchdog (unsigned long data) {struct iwm_priv *iwm = (struct iwm_priv *)data;
@@ -241,6 +268,7 @@ int iwm_priv_init(struct iwm_priv *iwm)INIT_DELAYED_WORK (&iwm->disconnect, iwm_disconnect_work);INIT_DELAYED_WORK (&iwm->ct_kill_delay, iwm_ct_kill_work);INIT_WORK (&iwm->reset_worker, iwm_reset_worker); +INIT_WORK (&iwm->auth_retry_worker, iwm_auth_retry_worker);INIT_LIST_HEAD (&iwm->bss_list);skb_queue_head_init (&iwm->rx_list);
drivers/net/wireless/iwmc3200wifi/rx.c +23 -5
@@ -502,6 +502,18 @@ static int iwm_mlme_assoc_start(struct iwm_priv *iwm, u8 *buf,return 0 ; } +static u8 iwm_is_open_wep_profile (struct iwm_priv *iwm) +{ +if ((iwm->umac_profile->sec.ucast_cipher ==UMAC_CIPHER_TYPE_WEP_40 || + iwm->umac_profile->sec.ucast_cipher ==UMAC_CIPHER_TYPE_WEP_104 ) && + (iwm->umac_profile->sec.ucast_cipher == + iwm->umac_profile->sec.mcast_cipher) && + (iwm->umac_profile->sec.auth_type ==UMAC_AUTH_TYPE_OPEN )) +return 1 ; + +return 0 ; +} +static int iwm_mlme_assoc_complete (struct iwm_priv *iwm,u8 *buf,unsigned long buf_size,struct iwm_wifi_cmd *cmd)
@@ -567,11 +579,17 @@ static int iwm_mlme_assoc_complete(struct iwm_priv *iwm, u8 *buf, goto ibss;if (!test_bit (IWM_STATUS_RESETTING , &iwm->status)) -cfg80211_connect_result (iwm_to_ndev (iwm), - complete->bssid, -NULL ,0 ,NULL ,0 , -WLAN_STATUS_UNSPECIFIED_FAILURE , -GFP_KERNEL ); +if (!iwm_is_open_wep_profile (iwm)) { +cfg80211_connect_result (iwm_to_ndev (iwm), + complete->bssid, +NULL ,0 ,NULL ,0 , +WLAN_STATUS_UNSPECIFIED_FAILURE , +GFP_KERNEL ); + }else { +/* Let's try shared WEP auth */ +IWM_ERR (iwm,"Trying WEP shared auth\n" ); +schedule_work (&iwm->auth_retry_worker); + }else cfg80211_disconnected (iwm_to_ndev (iwm),0 ,NULL ,0 ,GFP_KERNEL );
Signature · 1 line
1.6.0.4
PATCH 14/16 iwmc3200wifi: Support unexpected reboot barker
From: Samuel Ortiz <[email protected]>
We can receive unexpected reboot barker at any time, and we're supposed to reset the whole device then.
--- drivers/net/wireless/iwmc3200wifi/rx.c | 8 ++++++++ 1 files changed, 8 insertions(+), 0 deletions(-)
drivers/net/wireless/iwmc3200wifi/rx.c +8 -0
@@ -1322,6 +1322,14 @@ int iwm_rx_handle(struct iwm_priv *iwm, u8 *buf, unsigned long buf_size)switch (le32_to_cpu (hdr->cmd)) {case UMAC_REBOOT_BARKER : +if (test_bit (IWM_STATUS_READY , &iwm->status)) { +IWM_ERR (iwm,"Unexpected BARKER\n" ); + +schedule_work (&iwm->reset_worker); + +return 0 ; + } +return iwm_notif_send (iwm,NULL ,IWM_BARKER_REBOOT_NOTIFICATION ,IWM_SRC_UDMA , buf, buf_size);case UMAC_ACK_BARKER :
Signature · 1 line
1.6.0.4
PATCH 15/16 iwmc3200wifi: Set wiphy firmware version
From: Samuel Ortiz <[email protected]>
Our wiphy firmware version is a combination of the UMAC and LMAC ones.
--- drivers/net/wireless/iwmc3200wifi/fw.c | 7 +++++++ drivers/net/wireless/iwmc3200wifi/iwm.h | 2 ++ drivers/net/wireless/iwmc3200wifi/main.c | 4 ++++ 3 files changed, 13 insertions(+), 0 deletions(-)
drivers/net/wireless/iwmc3200wifi/fw.c +7 -0
@@ -217,6 +217,13 @@ static int iwm_load_img(struct iwm_priv *iwm, const char *img_name)IWM_BUILD_YEAR (build_date),IWM_BUILD_MONTH (build_date), IWM_BUILD_DAY(build_date)); +if (!strcmp (img_name, iwm->bus_ops->umac_name)) +sprintf (iwm->umac_version,"%02X.%02X" , + ver->major, ver->minor); + +if (!strcmp (img_name, iwm->bus_ops->lmac_name)) +sprintf (iwm->lmac_version,"%02X.%02X" , + ver->major, ver->minor); err_release_fw:release_firmware (fw);
drivers/net/wireless/iwmc3200wifi/iwm.h +2 -0
@@ -294,6 +294,8 @@ struct iwm_priv {int resp_ie_len;struct iwm_fw_error_hdr *last_fw_err; +char umac_version[8 ]; +char lmac_version[8 ]; char private[0] __attribute__((__aligned__(NETDEV_ALIGN))); };
drivers/net/wireless/iwmc3200wifi/main.c +4 -0
@@ -629,6 +629,7 @@ static int __iwm_up(struct iwm_priv *iwm) {int ret;struct iwm_notif *notif_reboot, *notif_ack =NULL ; +struct wiphy *wiphy =iwm_to_wiphy (iwm); ret =iwm_bus_enable (iwm);if (ret) {
@@ -690,6 +691,9 @@ static int __iwm_up(struct iwm_priv *iwm) goto err_disable; } +snprintf (wiphy->fw_version,sizeof (wiphy->fw_version),"L%s_U%s" , + iwm->lmac_version, iwm->umac_version); +/* We configure the UMAC and enable the wifi module */ ret = iwm_send_umac_config(iwm, cpu_to_le32(UMAC_RST_CTRL_FLG_WIFI_CORE_EN) |
Signature · 1 line
1.6.0.4
PATCH 16/16 iwmc3200wifi: handle coexistence radio notification
Handle WiFi/WiMax coexistence radio preemption notification event.
--- drivers/net/wireless/iwmc3200wifi/rx.c | 15 +++++++++++++++ 1 files changed, 15 insertions(+), 0 deletions(-)
drivers/net/wireless/iwmc3200wifi/rx.c +15 -0
@@ -733,6 +733,19 @@ static int iwm_mlme_update_sta_table(struct iwm_priv *iwm, u8 *buf,return 0 ; } +static int iwm_mlme_medium_lost (struct iwm_priv *iwm,u8 *buf, +unsigned long buf_size, +struct iwm_wifi_cmd *cmd) +{ +struct wiphy *wiphy =iwm_to_wiphy (iwm); + +IWM_DBG_NTF (iwm,DBG ,"WiFi/WiMax coexistence radio is OFF\n" ); + +wiphy_rfkill_set_hw_state (wiphy, true); + +return 0 ; +} +static int iwm_mlme_update_bss_table (struct iwm_priv *iwm,u8 *buf,unsigned long buf_size,struct iwm_wifi_cmd *cmd)
@@ -919,6 +932,8 @@ static int iwm_ntf_mlme(struct iwm_priv *iwm, u8 *buf,case WIFI_IF_NTFY_EXTENDED_IE_REQUIRED :IWM_DBG_MLME (iwm,DBG ,"Extended IE required\n" );break ; +case WIFI_IF_NTFY_RADIO_PREEMPTION : +return iwm_mlme_medium_lost (iwm, buf, buf_size, cmd);case WIFI_IF_NTFY_BSS_TRK_TABLE_CHANGED :return iwm_mlme_update_bss_table (iwm, buf, buf_size, cmd);case WIFI_IF_NTFY_BSS_TRK_ENTRIES_REMOVED :
Signature · 1 line
1.6.0.4
Re: [PATCH 14/16] iwmc3200wifi: Support unexpected reboot barker
In reply to Zhu YiQuoted 4 lines · Zhu Yi
From: Samuel Ortiz <[email protected]>
We can receive unexpected reboot barker at any time, and we're supposed to reset the whole device then.
What do yo mean, by whole device ? And who is we in this context?
Thanks
Tomas
Quoted 34 lines
Signed-off-by Samuel Ortiz <[email protected]>Signed-off-by Zhu Yi <[email protected]>---
drivers/net/wireless/iwmc3200wifi/rx.c | 8 ++++++++1 files changed, 8 insertions(+), 0 deletions(-)drivers/net/wireless/iwmc3200wifi/rx.c +0
-0@@ -1322,6 +1322,14 @@ int iwm_rx_handle(struct iwm_priv *iwm, u8 *buf, unsigned long buf_size) switch (le32_to_cpu(hdr->cmd)) {case
UMAC_REBOOT_BARKER:
+ if (test_bit(IWM_STATUS_READY, &iwm->status)) {
+IWM_ERR(iwm, "Unexpected BARKER\n");drivers/net/wireless/iwmc3200wifi/rx.c +6
-0+ + schedule_work(&iwm->reset_worker); + + return 0; + } +return
iwm_notif_send(iwm, NULL, IWM_BARKER_REBOOT_NOTIFICATION, IWM_SRC_UDMA, buf, buf_size); caseUMAC_ACK_BARKER:
--
1.6.0.4--
To unsubscribe from this list: send the line "unsubscribe linux-wireless" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
RE: [PATCH 14/16] iwmc3200wifi: Support unexpected reboot barker
SGkgVG9tYXMhDQoNCj4gLS0tLS1PcmlnaW5hbCBNZXNzYWdlLS0tLS0NCj4gRnJvbTogVG9tYXMg V2lua2xlciBbbWFpbHRvOnRvbWFzd0BnbWFpbC5jb21dDQo+IFNlbnQ6IDIwMDnE6jEw1MIxN8jV IDY6MDcNCj4gVG86IFpodSwgWWkNCj4gQ2M6IGxpbnZpbGxlQHR1eGRyaXZlci5jb207IGxpbnV4 LXdpcmVsZXNzQHZnZXIua2VybmVsLm9yZzsgU2FtdWVsIE9ydGl6DQo+IFN1YmplY3Q6IFJlOiBb UEFUQ0ggMTQvMTZdIGl3bWMzMjAwd2lmaTogU3VwcG9ydCB1bmV4cGVjdGVkIHJlYm9vdCBiYXJr ZXINCj4gDQo+IE9uIEZyaSwgT2N0IDE2LCAyMDA5IGF0IDc6MTggQU0sIFpodSBZaSA8eWkuemh1 QGludGVsLmNvbT4gd3JvdGU6DQo+ID4gRnJvbTogU2FtdWVsIE9ydGl6IDxzYW1lb0BsaW51eC5p bnRlbC5jb20+DQo+ID4NCj4gPiBXZSBjYW4gcmVjZWl2ZSB1bmV4cGVjdGVkIHJlYm9vdCBiYXJr ZXIgYXQgYW55IHRpbWUsIGFuZCB3ZSdyZSBzdXBwb3NlZCB0bw0KPiA+IHJlc2V0IHRoZSB3aG9s ZSBkZXZpY2UgdGhlbi4NCj4gDQo+IFdoYXQgZG8geW8gbWVhbiwgYnkgd2hvbGUgZGV2aWNlID8g QW5kIHdobyBpcyB3ZSBpbiB0aGlzIGNvbnRleHQ/DQoNCldlIGFyZSB0YWxraW5nIGZyb20gdGhl IHdpZmkgZHJpdmVyJ3MgcGVyc3BlY3RpdmUuIFRoZSBjb2RlIGlzIG9yaWdpbmFsbHkgdXNlZCBv bmx5IGZvciBTViB0ZXN0aW5nLiBUaGVuIHdlIGZpbmQgaXQgbWlnaHQgYmUgdXNlZnVsIGluIHRo ZSBnZW5lcmFsIGNhc2UuIFN1cHBvc2UgdGhlIGRyaXZlciBnZXQgYSBSRUJPT1RfQkFSS0VSIGZy b20gdGhlIGNhcmQgKGZvciB3aGF0ZXZlciByZWFzb24pLCBpcyByZXNldHRpbmcgdGhlIGRldmlj ZSB0aGUgY29ycmVjdCBiZWhhdmlvcj8NCg0KVGhhbmtzLA0KLXlpDQo=
Re: [PATCH 03/16] iwmc3200wifi: WPS support
In reply to Zhu YiHi Yi,
Quoted 16 lines
From: Samuel Ortiz <[email protected]>
By setting the WSC profile flag, we now support WPS as an enrollee.
Signed-off-by Samuel Ortiz <[email protected]>Signed-off-by Zhu Yi <[email protected]>--- drivers/net/wireless/iwmc3200wifi/cfg80211.c | 7 +++++++ drivers/net/wireless/iwmc3200wifi/commands.h | 3 +++ 2 files changed, 10 insertions(+), 0 deletions(-)drivers/net/wireless/iwmc3200wifi/cfg80211.c +0
-0
drivers/net/wireless/iwmc3200wifi/cfg80211.c static int iwm_cfg80211_connect(struct wiphy *wiphy, struct net_device *dev, · line 637
Quoted 10 lines
drivers/net/wireless/iwmc3200wifi/cfg80211.c +7
-0@@ -628,6 +628,13 @@ static int iwm_cfg80211_connect(struct wiphy *wiphy, struct net_device *dev, iwm->default_key = sme->key_idx; } +/* WPA and open AUTH type from wpa_s means WPS (a.k.a. WSC) */ +if ((iwm->umac_profile->sec.flags & + (UMAC_SEC_FLG_WPA_ON_MSK |UMAC_SEC_FLG_RSNA_ON_MSK )) && + iwm->umac_profile->sec.auth_type ==UMAC_AUTH_TYPE_OPEN ) { + iwm->umac_profile->sec.flags =UMAC_SEC_FLG_WSC_ON_MSK ; + } +
I don't wanna be picky, but what coding style are you following here? The indentation makes no sense and doesn't improve readability.
Regards
Marcel
Re: [PATCH 03/16] iwmc3200wifi: WPS support
Quoted 21 lines · Marcel Holtmann
Hi Yi,
Quoted 19 lines
From: Samuel Ortiz <[email protected]>
By setting the WSC profile flag, we now support WPS as an enrollee.
Signed-off-by Samuel Ortiz <[email protected]>Signed-off-by Zhu Yi <[email protected]>--- drivers/net/wireless/iwmc3200wifi/cfg80211.c | 7 +++++++ drivers/net/wireless/iwmc3200wifi/commands.h | 3 +++ 2 files changed, 10 insertions(+), 0 deletions(-)drivers/net/wireless/iwmc3200wifi/cfg80211.c +0
-0@@ -628,6 +628,13 @@ static int iwm_cfg80211_connect(struct wiphy *wiphy, struct net_device *dev, iwm->default_key = sme->key_idx; }
Quoted 10 lines
drivers/net/wireless/iwmc3200wifi/cfg80211.c static int iwm_cfg80211_connect(struct wiphy *wiphy, struct net_device *dev, · line 637
Quoted 7 lines
drivers/net/wireless/iwmc3200wifi/cfg80211.c +7
-0+/* WPA and open AUTH type from wpa_s means WPS (a.k.a. WSC) */ +if ((iwm->umac_profile->sec.flags & + (UMAC_SEC_FLG_WPA_ON_MSK |UMAC_SEC_FLG_RSNA_ON_MSK )) && + iwm->umac_profile->sec.auth_type ==UMAC_AUTH_TYPE_OPEN ) { + iwm->umac_profile->sec.flags =UMAC_SEC_FLG_WSC_ON_MSK ; + } +I don't wanna be picky, but what coding style are you following here? The indentation makes no sense and doesn't improve readability.
Given the length and complication of the conditions, the indentation seems fine to me. How would you do it?
John
Signature · 2 lines
John W. Linville Someday the world will need a hero, and you [email protected] might be all we have. Be ready.
Re: [PATCH 03/16] iwmc3200wifi: WPS support
Hi John,
Quoted 30 lines
Quoted 19 lines
Quoted 19 lines
From: Samuel Ortiz <[email protected]>
By setting the WSC profile flag, we now support WPS as an enrollee.
Signed-off-by Samuel Ortiz <[email protected]>Signed-off-by Zhu Yi <[email protected]>--- drivers/net/wireless/iwmc3200wifi/cfg80211.c | 7 +++++++ drivers/net/wireless/iwmc3200wifi/commands.h | 3 +++ 2 files changed, 10 insertions(+), 0 deletions(-)drivers/net/wireless/iwmc3200wifi/cfg80211.c +0
-0@@ -628,6 +628,13 @@ static int iwm_cfg80211_connect(struct wiphy *wiphy, struct net_device *dev, iwm->default_key = sme->key_idx; }Quoted 10 lines
drivers/net/wireless/iwmc3200wifi/cfg80211.c static int iwm_cfg80211_connect(struct wiphy *wiphy, struct net_device *dev, · line 637
Quoted 7 lines
drivers/net/wireless/iwmc3200wifi/cfg80211.c +7
-0+/* WPA and open AUTH type from wpa_s means WPS (a.k.a. WSC) */ +if ((iwm->umac_profile->sec.flags & + (UMAC_SEC_FLG_WPA_ON_MSK |UMAC_SEC_FLG_RSNA_ON_MSK )) && + iwm->umac_profile->sec.auth_type ==UMAC_AUTH_TYPE_OPEN ) { + iwm->umac_profile->sec.flags =UMAC_SEC_FLG_WSC_ON_MSK ; + } +I don't wanna be picky, but what coding style are you following here? The indentation makes no sense and doesn't improve readability.
Quoted 2 lines
Given the length and complication of the conditions, the indentation seems fine to me. How would you do it?
it is double indentation of iwm->umac_profile... and (UMAC... and iwm->uwm_profile are not even on the same vertical. If I stare long enough at it, I can see a certain reasoning for it, but it is an ugly block. Some extra macros might make this more readable. However if you are fine with it, then that is good enough. I just mentioned it, because I read the if clause wrongly when reviewing the patches.
Regards
Marcel
Quoted 3 lines · Zhu Yi
Add BGN SKU sdio device id.
Signed-off-by Zhu Yi <[email protected]>
I will remove SDIO_DEVICE_ID_INTEL_IWMC3200WIF from sdio_ids.h
Quoted 29 lines
---
drivers/net/wireless/iwmc3200wifi/sdio.c | 6 ++++--1 files changed, 4 insertions(+), 2 deletions(-)drivers/net/wireless/iwmc3200wifi/sdio.c +4
-3@@ -493,8 +493,10 @@ static void iwm_sdio_remove(struct sdio_func *func) } static const struct sdio_device_id iwm_sdio_ids[] = { - { SDIO_DEVICE(SDIO_VENDOR_ID_INTEL, - SDIO_DEVICE_ID_INTEL_IWMC3200WIFI) }, + /* Global/AGN SKU */ + { SDIO_DEVICE(SDIO_VENDOR_ID_INTEL, 0x1403) }, + /* BGN SKU */ + { SDIO_DEVICE(SDIO_VENDOR_ID_INTEL, 0x1408) }, { /* end: all zeroes */ }, }; MODULE_DEVICE_TABLE(sdio, iwm_sdio_ids); --1.6.0.4
--
To unsubscribe from this list: send the line "unsubscribe linux-wireless" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html