Skip to contentSkip to conversation

setenv: do console redirection even if previously unset

PATCH New Alessandro Rubini 2 participants 2 messages Oct 8, 2009 – Oct 18, 2009

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 setenv: do console redirection even if previously unset

From: Alessandro Rubini <[email protected]>

If "stdout" is not previously set, doing "setenv stdout lcd" had no effect, since console redirection only worked if the environment variable was already set; the second time you run setenv it worked. Most default environments lack stdin/out/err definitions, so I'm sure I'm not alone with this problem.

This patch simply moves a block of code out of a conditional, to do the same work even if the variable was previously unset.

---
 common/cmd_nvedit.c |   62 +++++++++++++++++++++++++-------------------------
 1 files changed, 31 insertions(+), 31 deletions(-)
common/cmd_nvedit.c +31 -31
index 2186205..9f8d531 100644
@@ -202,6 +202,37 @@ int _do_setenv (int flag, int argc, char *argv[])
 			break;
 	}
 
+	/* Check for console redirection */
+	if (strcmp(name,"stdin") == 0) {
+		console = stdin;
+	} else if (strcmp(name,"stdout") == 0) {
+		console = stdout;
+	} else if (strcmp(name,"stderr") == 0) {
+		console = stderr;
+	}
+
+	if (console != -1) {
+		if (argc < 3) {		/* Cannot delete it! */
+			printf("Can't delete \"%s\"\n", name);
+			return 1;
+		}
+
+#ifdef CONFIG_CONSOLE_MUX
+		i = iomux_doenv(console, argv[2]);
+		if (i)
+			return i;
+#else
+		/* Try assigning specified device */
+		if (console_assign (console, argv[2]) < 0)
+			return 1;
+
+#ifdef CONFIG_SERIAL_MULTI
+		if (serial_assign (argv[2]) < 0)
+			return 1;
+#endif
+#endif /* CONFIG_CONSOLE_MUX */
+	}
+
 	/*
 	 * Delete any existing definition
 	 */
@@ -229,37 +260,6 @@ int _do_setenv (int flag, int argc, char *argv[])
 		}
 #endif
 
-		/* Check for console redirection */
-		if (strcmp(name,"stdin") == 0) {
-			console = stdin;
-		} else if (strcmp(name,"stdout") == 0) {
-			console = stdout;
-		} else if (strcmp(name,"stderr") == 0) {
-			console = stderr;
-		}
-
-		if (console != -1) {
-			if (argc < 3) {		/* Cannot delete it! */
-				printf("Can't delete \"%s\"\n", name);
-				return 1;
-			}
-
-#ifdef CONFIG_CONSOLE_MUX
-			i = iomux_doenv(console, argv[2]);
-			if (i)
-				return i;
-#else
-			/* Try assigning specified device */
-			if (console_assign (console, argv[2]) < 0)
-				return 1;
-
-#ifdef CONFIG_SERIAL_MULTI
-			if (serial_assign (argv[2]) < 0)
-				return 1;
-#endif
-#endif /* CONFIG_CONSOLE_MUX */
-		}
-
 		/*
 		 * Switch to new baudrate if new baudrate is supported
 		 */
Signature · 1 line
1.6.0.2
#1 lore raw

PATCH 1/1 setenv: do console redirection even if previously unset

Dear Alessandro Rubini,

Quoted 8 lines · In message <[email protected]> you wrote:

From: Alessandro Rubini <[email protected]>

If "stdout" is not previously set, doing "setenv stdout lcd" had no effect, since console redirection only worked if the environment variable was already set; the second time you run setenv it worked. Most default environments lack stdin/out/err definitions, so I'm sure I'm not alone with this problem.

Quoted 8 lines

This patch simply moves a block of code out of a conditional, to do the same work even if the variable was previously unset.

---
 common/cmd_nvedit.c |   62 +++++++++++++++++++++++++-------------------------
 1 files changed, 31 insertions(+), 31 deletions(-)

Applied, thanks.

Best regards,

Wolfgang Denk

Signature · 4 lines
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
Our business is run on trust.  We trust you will pay in advance.