Skip to contentSkip to conversation

AGAIN: support for AMD 10H and 11H

PATCH In review Hans-Frieder Vogt 2 participants 3 messages Oct 4, 2009 – Oct 21, 2009

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 AGAIN: support for AMD 10H and 11H

Hi,

picking up the discussion that happened in May (see
http://lists.lm-sensors.org/pipermail/lm-sensors/2009-May/025896.html
and following discussion), it seems that the decision taken at the time was a bit too general.
The latest revisions of the Revision Guide for AMD Family 10h processors (from Rev. 3.50) show that only model 'B' of the Family 10h processors is affected by the erratum #319 (inconsistent temperature reporting).
I have a model 'C' Family 10h processor and can confirm that the temperatures reported by the processor do make sense.

I suggest therefore a patch based on Jasminders proposal, slightly modified to exclude only the affected family 10h model 'B' processors, but accepting the other models (i.e. currently 'C' and 'D').
Rudolf, what do you think?

Thanks,
Hans-Frieder

---
 drivers/hwmon/k8temp.c |   39 +++++++++++++++++++++++++++++++++++++--
 1 file changed, 37 insertions(+), 2 deletions(-)
drivers/hwmon/k8temp.c +25 -2
@@ -1,5 +1,6 @@
 /*
  * k8temp.c - Linux kernel module for hardware monitoring
+ * for AMD K8 and derivates
  *
  * Copyright (C) 2006 Rudolf Marek <[email protected]>
  *
@@ -33,7 +34,7 @@
 #include <linux/mutex.h>
 #include <asm/processor.h>
 
-#define TEMP_FROM_REG(val)	(((((val) >> 16) & 0xff) - 49) * 1000)
+#define REG_TCTL	0xa4
 #define REG_TEMP	0xe4
 #define SEL_PLACE	0x40
 #define SEL_CORE	0x04
@@ -52,6 +53,14 @@ struct k8temp_data {
 	u32 temp_offset;
 };
 
+static unsigned long temp_from_reg(unsigned long val)
+{
+	if (boot_cpu_data.x86 > 0xf)
+		return ((val) >> 21) * 125;
+	else
+		return ((((val) >> 16) & 0xff) - 49) * 1000;
+}
+
 static struct k8temp_data *k8temp_update_device(struct device *dev)
 {
 	struct k8temp_data *data = dev_get_drvdata(dev);
@@ -62,6 +71,11 @@ static struct k8temp_data *k8temp_update
 
 	if (!data->valid
 	    || time_after(jiffies, data->last_updated + HZ)) {
+		if (boot_cpu_data.x86 > 0xf) {
+			pci_read_config_dword(pdev, REG_TCTL,
+					      &data->temp[0][0]);
+			goto update_done;
+		}
 		pci_read_config_byte(pdev, REG_TEMP, &tmp);
 		tmp &= ~(SEL_PLACE | SEL_CORE);		/* Select sensor 0, core0 */
 		pci_write_config_byte(pdev, REG_TEMP, tmp);
@@ -89,6 +103,7 @@ static struct k8temp_data *k8temp_update
 			}
 		}
 
+update_done:
 		data->last_updated = jiffies;
 		data->valid = 1;
 	}
@@ -123,7 +138,7 @@ static ssize_t show_temp(struct device *
 	if (data->swap_core_select)
 		core = core ? 0 : 1;
 
-	temp = TEMP_FROM_REG(data->temp[core][place]) + data->temp_offset;
+	temp = temp_from_reg(data->temp[core][place]) + data->temp_offset;
 
 	return sprintf(buf, "%d\n", temp);
 }
@@ -138,6 +153,8 @@ static DEVICE_ATTR(name, S_IRUGO, show_n
 
 static struct pci_device_id k8temp_ids[] = {
 	{ PCI_DEVICE(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_K8_NB_MISC) },
+	{ PCI_DEVICE(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_10H_NB_MISC) },
+	{ PCI_DEVICE(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_11H_NB_MISC) },
 	{ 0 },
 };
 
@@ -158,6 +175,23 @@ static int __devinit k8temp_probe(struct
 	}
 
 	model = boot_cpu_data.x86_model;
+
+	if ((boot_cpu_data.x86 = 0x10) && (model = 2)) {
+		/*
+		 * AMD 10H cpus rev. B report Inaccurate Temperature
+		 * Measurement :
+		 * http://www.amd.com/us-

en/assets/content_type/white_papers_and_tech_docs/41322.pdf
+ * Errata #319
+ */
+ dev_err(&pdev->dev, "Reported temperature may be inconsistent, "
+ "therefore rejected here - see erratum #319\n");
+ err = -ENODEV;
+ goto exit_free;
+ }
+ if (boot_cpu_data.x86 > 0xf) {
+ goto probe_done;
+ }
+
stepping = boot_cpu_data.x86_mask;

switch (boot_cpu_data.x86) {
@@ -226,6 +260,7 @@ static int __devinit k8temp_probe(struct
data->sensorsp &= ~SEL_CORE;
}

+probe_done:
data->name = "k8temp";
mutex_init(&data->update_lock);
dev_set_drvdata(&pdev->dev, data);

Hans-Frieder Vogt e-mail: hfvogt <at> gmx .dot. net

_______________________________________________
lm-sensors mailing list
[email protected]
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors

maintainer
#1 lore raw

Hi all,

Thank you. It seems AMD fixed that. Maybe we would need to avoid the goto.

drivers/hwmon/k8temp.c static struct k8temp_data *k8temp_update · line 78

Quoted 7 lines
drivers/hwmon/k8temp.c +5 -0
 	if (!data->valid
 	    || time_after(jiffies, data->last_updated + HZ)) {
+		if (boot_cpu_data.x86 > 0xf) {
+			pci_read_config_dword(pdev, REG_TCTL,
+					      &data->temp[0][0]);
+			goto update_done;
+		}

Hm goto can be used only to jump to error paths.

Review

Quoted 11 lines
drivers/hwmon/k8temp.c +6 -0
+
+	if ((boot_cpu_data.x86 = 0x10) && (model = 2)) {
+		/*
+		 * AMD 10H cpus rev. B report Inaccurate Temperature
+		 * Measurement :
+		 * http://www.amd.com/us-

en/assets/content_type/white_papers_and_tech_docs/41322.pdf

(quoted diff) +4 -0
+		 *     Errata #319
+		 */
+		dev_err(&pdev->dev, "Reported temperature may be inconsistent, "
+			"therefore rejected here - see erratum #319\n");

Maybe the message could be - Erratum #319 detected, refusing to load.

Review

Quoted 1 line
(quoted diff) +1 -0
+		err = -ENODEV;

Thank you

Rudolf

_______________________________________________
lm-sensors mailing list
[email protected]
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors

#2 lore raw
In reply to Hans-Frieder Vogt

Hi,

Quoted 25 lines

Thank you. It seems AMD fixed that. Maybe we would need to avoid the goto.

Review

Quoted 7 lines
(quoted diff) +5 -0
 	if (!data->valid
 	    || time_after(jiffies, data->last_updated + HZ)) {
+		if (boot_cpu_data.x86 > 0xf) {
+			pci_read_config_dword(pdev, REG_TCTL,
+					      &data->temp[0][0]);
+			goto update_done;
+		}

Hm goto can be used only to jump to error paths.

Review

Quoted 11 lines
(quoted diff) +6 -0
+
+	if ((boot_cpu_data.x86 = 0x10) && (model = 2)) {
+		/*
+		 * AMD 10H cpus rev. B report Inaccurate Temperature
+		 * Measurement :
+		 * http://www.amd.com/us-

en/assets/content_type/white_papers_and_tech_docs/41322.pdf

(quoted diff) +4 -0
+		 *     Errata #319
+		 */
+		dev_err(&pdev->dev, "Reported temperature may be inconsistent, "
+			"therefore rejected here - see erratum #319\n");

Maybe the message could be - Erratum #319 detected, refusing to load.

Quoted 5 lines

Review

Quoted 1 line
(quoted diff) +1 -0
+		err = -ENODEV;

Thank you

Rudolf

thanks for your comments, Rudolf. Here is an updated patch that is a bit more structured and only uses gotos for error paths.

---
 drivers/hwmon/k8temp.c |  133 
++++++++++++++++++++++++++++++++++++++-------------------------
 1 file changed, 82 insertions(+), 51 deletions(-)
drivers/hwmon/k8temp.c +72 -51
@@ -1,5 +1,6 @@
 /*
  * k8temp.c - Linux kernel module for hardware monitoring
+ * for AMD K8 and derivates
  *
  * Copyright (C) 2006 Rudolf Marek <[email protected]>
  *
@@ -33,7 +34,7 @@
 #include <linux/mutex.h>
 #include <asm/processor.h>
 
-#define TEMP_FROM_REG(val)	(((((val) >> 16) & 0xff) - 49) * 1000)
+#define REG_TCTL	0xa4
 #define REG_TEMP	0xe4
 #define SEL_PLACE	0x40
 #define SEL_CORE	0x04
@@ -52,6 +53,14 @@ struct k8temp_data {
 	u32 temp_offset;
 };
 
+static unsigned long temp_from_reg(unsigned long val)
+{
+	if (boot_cpu_data.x86 > 0xf)
+		return ((val) >> 21) * 125;
+	else
+		return ((((val) >> 16) & 0xff) - 49) * 1000;
+}
+
 static struct k8temp_data *k8temp_update_device(struct device *dev)
 {
 	struct k8temp_data *data = dev_get_drvdata(dev);
@@ -62,30 +71,35 @@ static struct k8temp_data *k8temp_update
 
 	if (!data->valid
 	    || time_after(jiffies, data->last_updated + HZ)) {
-		pci_read_config_byte(pdev, REG_TEMP, &tmp);
-		tmp &= ~(SEL_PLACE | SEL_CORE);		/* Select sensor 0, core0 */
-		pci_write_config_byte(pdev, REG_TEMP, tmp);
-		pci_read_config_dword(pdev, REG_TEMP, &data->temp[0][0]);
-
-		if (data->sensorsp & SEL_PLACE) {
-			tmp |= SEL_PLACE;	/* Select sensor 1, core0 */
+		if (boot_cpu_data.x86 > 0xf) {
+			pci_read_config_dword(pdev, REG_TCTL,
+					      &data->temp[0][0]);
+		} else {
+			pci_read_config_byte(pdev, REG_TEMP, &tmp);
+			tmp &= ~(SEL_PLACE | SEL_CORE);		/* Select sensor 0, core0 */
 			pci_write_config_byte(pdev, REG_TEMP, tmp);
-			pci_read_config_dword(pdev, REG_TEMP,
-					      &data->temp[0][1]);
-		}
-
-		if (data->sensorsp & SEL_CORE) {
-			tmp &= ~SEL_PLACE;	/* Select sensor 0, core1 */
-			tmp |= SEL_CORE;
-			pci_write_config_byte(pdev, REG_TEMP, tmp);
-			pci_read_config_dword(pdev, REG_TEMP,
-					      &data->temp[1][0]);
+			pci_read_config_dword(pdev, REG_TEMP, &data->temp[0][0]);
 
 			if (data->sensorsp & SEL_PLACE) {
-				tmp |= SEL_PLACE;	/* Select sensor 1, core1 */
+				tmp |= SEL_PLACE;	/* Select sensor 1, core0 */
+				pci_write_config_byte(pdev, REG_TEMP, tmp);
+				pci_read_config_dword(pdev, REG_TEMP,
+						      &data->temp[0][1]);
+			}
+
+			if (data->sensorsp & SEL_CORE) {
+				tmp &= ~SEL_PLACE;	/* Select sensor 0, core1 */
+				tmp |= SEL_CORE;
 				pci_write_config_byte(pdev, REG_TEMP, tmp);
 				pci_read_config_dword(pdev, REG_TEMP,
-						      &data->temp[1][1]);
+						      &data->temp[1][0]);
+
+				if (data->sensorsp & SEL_PLACE) {
+					tmp |= SEL_PLACE;	/* Select sensor 1, core1 */
+					pci_write_config_byte(pdev, REG_TEMP, tmp);
+					pci_read_config_dword(pdev, REG_TEMP,
+							      &data->temp[1][1]);
+				}
 			}
 		}
 
@@ -123,7 +137,7 @@ static ssize_t show_temp(struct device *
 	if (data->swap_core_select)
 		core = core ? 0 : 1;
 
-	temp = TEMP_FROM_REG(data->temp[core][place]) + data->temp_offset;
+	temp = temp_from_reg(data->temp[core][place]) + data->temp_offset;
 
 	return sprintf(buf, "%d\n", temp);
 }
@@ -138,6 +152,8 @@ static DEVICE_ATTR(name, S_IRUGO, show_n
 
 static struct pci_device_id k8temp_ids[] = {
 	{ PCI_DEVICE(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_K8_NB_MISC) },
+	{ PCI_DEVICE(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_10H_NB_MISC) },
+	{ PCI_DEVICE(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_11H_NB_MISC) },
 	{ 0 },
 };
 
@@ -189,41 +205,56 @@ static int __devinit k8temp_probe(struct
 			data->temp_offset = 21000;
 		}
 
-		break;
-	}
+		pci_read_config_byte(pdev, REG_TEMP, &scfg);
+		scfg &= ~(SEL_PLACE | SEL_CORE);		/* Select sensor 0, core0 */
+		pci_write_config_byte(pdev, REG_TEMP, scfg);
+		pci_read_config_byte(pdev, REG_TEMP, &scfg);
 
-	pci_read_config_byte(pdev, REG_TEMP, &scfg);
-	scfg &= ~(SEL_PLACE | SEL_CORE);		/* Select sensor 0, core0 */
-	pci_write_config_byte(pdev, REG_TEMP, scfg);
-	pci_read_config_byte(pdev, REG_TEMP, &scfg);
-
-	if (scfg & (SEL_PLACE | SEL_CORE)) {
-		dev_err(&pdev->dev, "Configuration bit(s) stuck at 1!\n");
-		err = -ENODEV;
-		goto exit_free;
-	}
+		if (scfg & (SEL_PLACE | SEL_CORE)) {
+			dev_err(&pdev->dev, "Configuration bit(s) stuck at 1!\n");
+			err = -ENODEV;
+			goto exit_free;
+		}
 
-	scfg |= (SEL_PLACE | SEL_CORE);
-	pci_write_config_byte(pdev, REG_TEMP, scfg);
+		scfg |= (SEL_PLACE | SEL_CORE);
+		pci_write_config_byte(pdev, REG_TEMP, scfg);
 
-	/* now we know if we can change core and/or sensor */
-	pci_read_config_byte(pdev, REG_TEMP, &data->sensorsp);
+		/* now we know if we can change core and/or sensor */
+		pci_read_config_byte(pdev, REG_TEMP, &data->sensorsp);
 
-	if (data->sensorsp & SEL_PLACE) {
-		scfg &= ~SEL_CORE;	/* Select sensor 1, core0 */
-		pci_write_config_byte(pdev, REG_TEMP, scfg);
-		pci_read_config_dword(pdev, REG_TEMP, &temp);
-		scfg |= SEL_CORE;	/* prepare for next selection */
-		if (!((temp >> 16) & 0xff))	/* if temp is 0 -49C is not likely */
-			data->sensorsp &= ~SEL_PLACE;
-	}
+		if (data->sensorsp & SEL_PLACE) {
+			scfg &= ~SEL_CORE;	/* Select sensor 1, core0 */
+			pci_write_config_byte(pdev, REG_TEMP, scfg);
+			pci_read_config_dword(pdev, REG_TEMP, &temp);
+			scfg |= SEL_CORE;	/* prepare for next selection */
+			if (!((temp >> 16) & 0xff))	/* if temp is 0 -49C is not likely */
+				data->sensorsp &= ~SEL_PLACE;
+		}
 
-	if (data->sensorsp & SEL_CORE) {
-		scfg &= ~SEL_PLACE;	/* Select sensor 0, core1 */
-		pci_write_config_byte(pdev, REG_TEMP, scfg);
-		pci_read_config_dword(pdev, REG_TEMP, &temp);
-		if (!((temp >> 16) & 0xff))	/* if temp is 0 -49C is not likely */
-			data->sensorsp &= ~SEL_CORE;
+		if (data->sensorsp & SEL_CORE) {
+			scfg &= ~SEL_PLACE;	/* Select sensor 0, core1 */
+			pci_write_config_byte(pdev, REG_TEMP, scfg);
+			pci_read_config_dword(pdev, REG_TEMP, &temp);
+			if (!((temp >> 16) & 0xff))	/* if temp is 0 -49C is not likely */
+				data->sensorsp &= ~SEL_CORE;
+		}
+		break;
+	case 0x10:
+		if (model <= 2) {
+			/*
+			 * AMD 10H cpus rev. B report Inaccurate Temperature
+			 * Measurement :
+			 * http://www.amd.com/us-

en/assets/content_type/white_papers_and_tech_docs/41322.pdf
+ * Errata #319
+ */
+ dev_err(&pdev->dev, "Erratum #319 detected, refusing to"
+ " load.\n");
+ err = -ENODEV;
+ goto exit_free;
+ }
+ break;
+ case 0x11:
+ break;
}

data->name = "k8temp";

Hans-Frieder Vogt e-mail: hfvogt <at> gmx .dot. net

_______________________________________________
lm-sensors mailing list
[email protected]
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors