PCI Express-to-PCI Bridge: yenta_cardbus no bus associated!
Hi PCI Hackers,
i have trouble with an ExpressCard PCI Express-to-PCI Bridge manufactured by DUEL System under X86/32 Linux kernel 2.6.31.
The kernel will recognized the Texas Instruments XIO2000(A)/XIO2200(A) PCI Express-to-PCI Bridge and the attached Texas Instruments PCIxx12 Cardbus Controller, but the yenta socket driver will fail with the message:
yenta_cardbus 0000:0f:00.0: no bus associated! (try 'pci=assign-busses')
The output of dmesg looks like:
pci 0000:0e:00.0: supports D1 D2
pci 0000:0f:00.0: reg 10 32bit mmio: [0x000000-0x000fff] pci 0000:0f:00.0: supports D1 D2
pci 0000:0f:00.0: PME# supported from D0 D1 D2 D3hot D3cold pci 0000:0f:00.0: PME# disabled
pci 0000:0e:00.0: bridge io port: [0x00-0xfff]
pci 0000:0e:00.0: bridge 32bit mmio: [0x000000-0x0fffff] pci 0000:0e:00.0: bridge 64bit mmio pref: [0x000000-0x0fffff] pci 0000:0e:00.0: PCI bridge, secondary bus 0000:0f
pci 0000:0e:00.0: IO window: disabled pci 0000:0e:00.0: MEM window: 0xf1c00000-0xf1cfffff pci 0000:0e:00.0: PREFETCH window: disabled
decode_hpp: Could not get hotplug parameters. Use defaults pci 0000:0e:00.0: enabling device (0000 -> 0002)
pci 0000:0e:00.0: setting latency timer to 64yenta_cardbus 0000:0f:00.0: no bus associated! (try 'pci=assign-busses')
lspci -v shows:
0e:00.0 PCI bridge: Texas Instruments XIO2000(A)/XIO2200(A) PCI Express-to-PCI Bridge (rev 03) (prog-if 00 [Normal decode])
Physical Slot: 1
Flags: bus master, fast devsel, latency 0
Bus: primary=0e, secondary=0f, subordinate=0f, sec-latency=64
Memory behind bridge: f1c00000-f1cfffff
Capabilities: [50] Power Management version 2
Capabilities: [60] MSI: Enable- Count=1/16 Maskable- 64bit+
Capabilities: [80] Subsystem: Device 5678:1234
Capabilities: [90] Express PCI/PCI-X Bridge, MSI 00
Capabilities: [100] Advanced Error Reporting
0f:00.0 CardBus bridge: Texas Instruments PCIxx12 Cardbus Controller
Subsystem: Texas Instruments Device ac48 Flags: medium devsel, IRQ 255 Memory at f1c00000 (32-bit, non-prefetchable) [disabled] [size=4K] Bus: primary=00, secondary=00, subordinate=00, sec-latency=0 I/O window 0: 00000000-00000003 [disabled] I/O window 1: 00000000-00000003 [disabled] 16-bit legacy interface ports at 0001
Any idea where the problem is located or how can i fix it?
If you need further information or dumps please contact me.
Stefani
[Adding CCs.]
Quoted 57 lines · Stefani Seibold
Hi PCI Hackers,
i have trouble with an ExpressCard PCI Express-to-PCI Bridge manufactured by DUEL System under X86/32 Linux kernel 2.6.31.
The kernel will recognized the Texas Instruments XIO2000(A)/XIO2200(A) PCI Express-to-PCI Bridge and the attached Texas Instruments PCIxx12 Cardbus Controller, but the yenta socket driver will fail with the message:
yenta_cardbus0000:0f:00.0: no bus associated! (try 'pci=assign-busses')The output of dmesg looks like:
pci 0000:0e:00.0: supports D1 D2
pci 0000:0f:00.0: reg 10 32bit mmio: [0x000000-0x000fff] pci 0000:0f:00.0: supports D1 D2
pci 0000:0f:00.0: PME# supported from D0 D1 D2 D3hot D3cold pci 0000:0f:00.0: PME# disabled
pci 0000:0e:00.0: bridge io port: [0x00-0xfff]
pci 0000:0e:00.0: bridge 32bit mmio: [0x000000-0x0fffff] pci 0000:0e:00.0: bridge 64bit mmio pref: [0x000000-0x0fffff] pci 0000:0e:00.0: PCI bridge, secondary bus 0000:0fpci 0000:0e:00.0: IO window: disabled pci 0000:0e:00.0: MEM window: 0xf1c00000-0xf1cfffff pci 0000:0e:00.0: PREFETCH window: disabled
decode_hpp: Could not get hotplug parameters. Use defaults pci 0000:0e:00.0: enabling device (0000 -> 0002)
pci 0000:0e:00.0: setting latency timer to 64yenta_cardbus0000:0f:00.0: no bus associated! (try 'pci=assign-busses')lspci -v shows:
0e:00.0 PCI bridge: Texas Instruments XIO2000(A)/XIO2200(A) PCI Express-to-PCI Bridge (rev 03) (prog-if 00 [Normal decode])
Physical Slot: 1
Flags: bus master, fast devsel, latency 0
Bus: primary=0e, secondary=0f, subordinate=0f, sec-latency=64
Memory behind bridge: f1c00000-f1cfffff
Capabilities: [50] Power Management version 2
Capabilities: [60] MSI: Enable- Count=1/16 Maskable- 64bit+
Capabilities: [80] Subsystem: Device 5678:1234
Capabilities: [90] Express PCI/PCI-X Bridge, MSI 00
Capabilities: [100] Advanced Error Reporting0f:00.0 CardBus bridge: Texas Instruments PCIxx12 Cardbus Controller
Subsystem: Texas Instruments Device ac48 Flags: medium devsel, IRQ 255 Memory at f1c00000 (32-bit, non-prefetchable) [disabled] [size=4K] Bus: primary=00, secondary=00, subordinate=00, sec-latency=0 I/O window 0: 00000000-00000003 [disabled] I/O window 1: 00000000-00000003 [disabled] 16-bit legacy interface ports at 0001Any idea where the problem is located or how can i fix it?
If you need further information or dumps please contact me.
Hi PCI Hackers,
since i get no answer, it try to post my problem again.
I have trouble with an ExpressCard PCI Express-to-PCI Bridge manufactured by DUEL System under X86/32 Linux kernel 2.6.31.
The kernel will recognized the Texas Instruments XIO2000(A)/XIO2200(A) PCI Express-to-PCI Bridge and the attached Texas Instruments PCIxx12 Cardbus Controller, but the yenta socket driver will fail with the message:
yenta_cardbus 0000:0f:00.0: no bus associated! (try 'pci=assign-busses')
The output of dmesg looks like:
pci 0000:0e:00.0: supports D1 D2
pci 0000:0f:00.0: reg 10 32bit mmio: [0x000000-0x000fff] pci 0000:0f:00.0: supports D1 D2
pci 0000:0f:00.0: PME# supported from D0 D1 D2 D3hot D3cold pci 0000:0f:00.0: PME# disabled
pci 0000:0e:00.0: bridge io port: [0x00-0xfff]
pci 0000:0e:00.0: bridge 32bit mmio: [0x000000-0x0fffff] pci 0000:0e:00.0: bridge 64bit mmio pref: [0x000000-0x0fffff] pci 0000:0e:00.0: PCI bridge, secondary bus 0000:0f
pci 0000:0e:00.0: IO window: disabled pci 0000:0e:00.0: MEM window: 0xf1c00000-0xf1cfffff pci 0000:0e:00.0: PREFETCH window: disabled
decode_hpp: Could not get hotplug parameters. Use defaults pci 0000:0e:00.0: enabling device (0000 -> 0002)
pci 0000:0e:00.0: setting latency timer to 64yenta_cardbus 0000:0f:00.0: no bus associated! (try 'pci=assign-busses')
lspci -v shows:
0e:00.0 PCI bridge: Texas Instruments XIO2000(A)/XIO2200(A) PCI Express-to-PCI Bridge (rev 03) (prog-if 00 [Normal decode])
Physical Slot: 1
Flags: bus master, fast devsel, latency 0
Bus: primary=0e, secondary=0f, subordinate=0f, sec-latency=64
Memory behind bridge: f1c00000-f1cfffff
Capabilities: [50] Power Management version 2
Capabilities: [60] MSI: Enable- Count=1/16 Maskable- 64bit+
Capabilities: [80] Subsystem: Device 5678:1234
Capabilities: [90] Express PCI/PCI-X Bridge, MSI 00
Capabilities: [100] Advanced Error Reporting
0f:00.0 CardBus bridge: Texas Instruments PCIxx12 Cardbus Controller
Subsystem: Texas Instruments Device ac48
Flags: medium devsel, IRQ 255
Memory at f1c00000 (32-bit, non-prefetchable) [disabled] [size=4K]
Bus: primary=00, secondary=00, subordinate=00, sec-latency=0
I/O window 0: 00000000-00000003 [disabled]
I/O window 1: 00000000-00000003 [disabled]
16-bit legacy interface ports at 0001Any idea where the problem is located or how can i fix it?
If you need further information or dumps please contact me.
The kernel parameter 'pci=assign-busses' did not fix the problem.
Stefani
Quoted 3 lines · Stefani Seibold
If you need further information or dumps please contact me.
The kernel parameter 'pci=assign-busses' did not fix the problem.
What does dmesg say when you specify pci=assign-busses?
Signature · 4 lines
Matthew Wilcox Intel Open Source Technology Centre "Bill, look, we understand that you're interested in selling us this operating system, but compare it to ours. We can't possibly take such a retrograde step."
Am Samstag, den 24.10.2009, 14:34 -0600 schrieb Matthew Wilcox:
Quoted 7 lines · Stefani Seibold
Quoted 3 lines
If you need further information or dumps please contact me.
The kernel parameter 'pci=assign-busses' did not fix the problem.
What does dmesg say when you specify pci=assign-busses?
Okay, i tried it again with 'pci=assign-bussed'. All i get is a
decode_hpp: Could not get hotplug parameters. Use defaults
thats all. The express-card will not be detected.
Hey,
Quoted 6 lines · Stefani Seibold
Am Samstag, den 24.10.2009, 14:34 -0600 schrieb Matthew Wilcox:
Quoted 5 lines · Stefani Seibold
Quoted 3 lines
If you need further information or dumps please contact me.
The kernel parameter 'pci=assign-busses' did not fix the problem.
Quoted 8 lines
Quoted 2 lines
What does dmesg say when you specify pci=assign-busses?
Okay, i tried it again with 'pci=assign-bussed'. All i get is a
decode_hpp: Could not get hotplug parameters. Use defaultsthats all. The express-card will not be detected.
I assume the "d" at the end was just a typo -- and "lspci -vvv" looks the same?
Best,
Dominik
Quoted 11 lines
Quoted 7 lines
Okay, i tried it again with 'pci=assign-bussed'. All i get is a
decode_hpp: Could not get hotplug parameters. Use defaultsthats all. The express-card will not be detected.
I assume the "d" at the end was just a typo -- and "lspci -vvv" looks the same?
Yes, this was a typo. Here are the diff's of dmesg and lspci -vvv with and without "pci=assign-busses" after inserting the express card.
dmesg without 'pci=assign-busses':
----------------------------------
pci 0000:0e:00.0: supports D1 D2
pci 0000:0f:00.0: reg 10 32bit mmio: [0x000000-0x000fff] pci 0000:0f:00.0: supports D1 D2
pci 0000:0f:00.0: PME# supported from D0 D1 D2 D3hot D3cold pci 0000:0f:00.0: PME# disabled
pci 0000:0e:00.0: bridge io port: [0x00-0xfff]
pci 0000:0e:00.0: bridge 32bit mmio: [0x000000-0x0fffff] pci 0000:0e:00.0: bridge 64bit mmio pref: [0x000000-0x0fffff]
ACPI: Delete PCI Interrupt Routing Table for 0000:0f pci 0000:0e:00.0: PCI bridge, secondary bus 0000:0f
pci 0000:0e:00.0: IO window: disabled pci 0000:0e:00.0: MEM window: 0xf1c00000-0xf1cfffff pci 0000:0e:00.0: PREFETCH window: disabled
decode_hpp: Could not get hotplug parameters. Use defaults pci 0000:0e:00.0: enabling device (0000 -> 0002)
pci 0000:0e:00.0: setting latency timer to 64yenta_cardbus 0000:0f:00.0: no bus associated! (try 'pci=assign-busses')
CE: hpet increasing min_delta_ns to 50624 nsec
lspci -vvv without 'pci=assign-busses':
---------------------------------------
0e:00.0 PCI bridge: Texas Instruments XIO2000(A)/XIO2200(A) PCI Express-to-PCI Bridge (rev 03) (prog-if 00 [Normal decode])
Physical Slot: 1
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=0e, secondary=0f, subordinate=0f, sec-latency=64
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: f1c00000-f1cfffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Bridge: PM- B3+
Capabilities: [60] MSI: Enable- Count=1/16 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [80] Subsystem: Device 5678:1234
Capabilities: [90] Express (v1) PCI/PCI-X Bridge, MSI 00
DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+ BrConfRtry-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <64ns, L1 <1us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [100] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
0f:00.0 CardBus bridge: Texas Instruments PCIxx12 Cardbus Controller
Subsystem: Texas Instruments Device ac48 Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin A routed to IRQ 255 Region 0: Memory at f1c00000 (32-bit, non-prefetchable) [disabled] [size=4K] Bus: primary=00, secondary=00, subordinate=00, sec-latency=0 Memory window 0: 00000000-00000000 [disabled] (prefetchable) Memory window 1: 00000000-00000000 [disabled] (prefetchable) I/O window 0: 00000000-00000003 [disabled] I/O window 1: 00000000-00000003 [disabled] BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt- PostWrite- 16-bit legacy interface ports at 0001
dmesg with 'pci=assign-busses':
-------------------------------
pci 0000:05:00.0: supports D1 D2decode_hpp: Could not get hotplug parameters. Use defaults
lspci -vvv with 'pci=assign-busses':
------------------------------------
05:00.0 PCI bridge: Texas Instruments XIO2000(A)/XIO2200(A) PCI Express-to-PCI Bridge (rev 03) (prog-if 00 [Normal decode])
Physical Slot: 1
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Bus: primary=00, secondary=00, subordinate=00, sec-latency=64
I/O behind bridge: 00000000-00000fff
Memory behind bridge: 00000000-000fffff
Prefetchable memory behind bridge: 0000000000000000-00000000000fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Bridge: PM- B3+
Capabilities: [60] MSI: Enable- Count=1/16 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [80] Subsystem: Device 5678:1234
Capabilities: [90] Express (v1) PCI/PCI-X Bridge, MSI 00
DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+ BrConfRtry-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <64ns, L1 <1us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [100] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
Greetings,
Stefani