Skip to contentSkip to conversation

sh: mac address through private data for sh_eth on ecovec24

PATCH Applied Magnus Damm 2 participants 3 messages Oct 26, 2009 – Oct 28, 2009 SuperH

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 sh: mac address through private data for sh_eth on ecovec24

From: Magnus Damm <[email protected]>

Convert the ecovec24 board code to pass the mac address to the sh_eth driver using platform data. Also, remove the static clock to allow Runtime PM.

---

 arch/sh/boards/mach-ecovec24/setup.c |   33 ++++-----------------------------
 1 file changed, 4 insertions(+), 29 deletions(-)
arch/sh/boards/mach-ecovec24/setup.c +4 -29
@@ -414,12 +414,9 @@ static u8 mac_read(struct i2c_adapter *a
 	return buf;
 }
 
-#define MAC_LEN 6
-static void __init sh_eth_init(void)
+static void __init sh_eth_init(struct sh_eth_plat_data *pd)
 {
 	struct i2c_adapter *a = i2c_get_adapter(1);
-	struct clk *eth_clk;
-	u8 mac[MAC_LEN];
 	int i;
 
 	if (!a) {
@@ -427,33 +424,11 @@ static void __init sh_eth_init(void)
 		return;
 	}
 
-	eth_clk = clk_get(NULL, "eth0");
-	if (!eth_clk) {
-		pr_err("can not get eth0 clk\n");
-		return;
-	}
-
 	/* read MAC address frome EEPROM */
-	for (i = 0; i < MAC_LEN; i++) {
-		mac[i] = mac_read(a, 0x10 + i);
+	for (i = 0; i < sizeof(pd->mac_addr); i++) {
+		pd->mac_addr[i] = mac_read(a, 0x10 + i);
 		msleep(10);
 	}
-
-	/* clock enable */
-	clk_enable(eth_clk);
-
-	/* reset sh-eth */
-	ctrl_outl(0x1, SH_ETH_ADDR + 0x0);
-
-	/* set MAC addr */
-	ctrl_outl((mac[0] << 24) |
-		  (mac[1] << 16) |
-		  (mac[2] <<  8) |
-		  (mac[3] <<  0), SH_ETH_MAHR);
-	ctrl_outl((mac[4] <<  8) |
-		  (mac[5] <<  0), SH_ETH_MALR);
-
-	clk_put(eth_clk);
 }
 
 #define PORT_HIZA 0xA4050158
@@ -665,7 +640,7 @@ arch_initcall(arch_setup);
 
 static int __init devices_setup(void)
 {
-	sh_eth_init();
+	sh_eth_init(&sh_eth_plat);
 	return 0;
 }
 device_initcall(devices_setup);
#1 lore raw

PATCH 1/1 sh: mac address through private data for sh_eth on ms7724se

From: Magnus Damm <[email protected]>

Convert the ms7724se board code to pass the mac
address to the sh_eth driver using platform data.

---

This depends on the sh_eth platform data mac patch.

 arch/sh/boards/mach-se/7724/setup.c |   14 ++++----------
 1 file changed, 4 insertions(+), 10 deletions(-)
arch/sh/boards/mach-se/7724/setup.c +4 -10
@@ -507,7 +507,7 @@ static int __init sh_eth_is_eeprom_ready
 static void __init sh_eth_init(void)
 {
 	int i;
-	u16 mac[3];
+	u16 mac;
 
 	/* check EEPROM status */
 	if (!sh_eth_is_eeprom_ready())
@@ -521,16 +521,10 @@ static void __init sh_eth_init(void)
 		if (!sh_eth_is_eeprom_ready())
 			return;
 
-		mac[i] = ctrl_inw(EEPROM_DATA);
-		mac[i] = ((mac[i] & 0xFF) << 8) | (mac[i] >> 8); /* swap */
+		mac = ctrl_inw(EEPROM_DATA);
+		sh_eth_plat.mac_addr[i << 1] = mac & 0xff;
+		sh_eth_plat.mac_addr[(i << 1) + 1] = mac >> 8;
 	}
-
-	/* reset sh-eth */
-	ctrl_outl(0x1, SH_ETH_ADDR + 0x0);
-
-	/* set MAC addr */
-	ctrl_outl(((mac[0] << 16) | (mac[1])), SH_ETH_MAHR);
-	ctrl_outl((mac[2]), SH_ETH_MALR);
 }
 
 #define SW4140    0xBA201000
Applied
#2 lore raw

Re: [PATCH] sh: mac address through private data for sh_eth on ms7724se

In reply to Magnus Damm
Quoted 2 lines · Magnus Damm

Convert the ms7724se board code to pass the mac
address to the sh_eth driver using platform data.

Quoted 1 line · Magnus Damm

Add support for cn8 and SDHI1 to the ms7724se board.

Applied, thanks.