Skip to contentSkip to conversation

e100: e100_phy_init() isolates selected PHY, causes 10 second boot delay

PATCH Applied Jeff Kirsher 2 participants 2 messages Oct 29, 2009 – Oct 30, 2009

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 e100: e100_phy_init() isolates selected PHY, causes 10 second boot delay

From: Bruce Allan <[email protected]>

A change in how PHYs are electrically isolated caused all PHYs to be isolated followed by reverting that isolation for the selected PHY. Unfortunately, isolating the selected PHY for even a short period of time can result in DHCP negotiation taking more than 10 seconds on certain embedded configurations delaying boot time as reported by Bernhard Kaindl. This patch reverts the change to how PHYs are isolated yet still works around the issue for 82552 needing the selected PHY's BMCR register to be written after the unused PHYs are isolated. This code is moved below the setting of nic->phy ID in order to do the 82552-specific workaround.

---

 drivers/net/e100.c |   26 +++++++++++++++++++-------
 1 files changed, 19 insertions(+), 7 deletions(-)
drivers/net/e100.c +19 -7
index 679965c..d19b084 100644
@@ -1426,19 +1426,31 @@ static int e100_phy_init(struct nic *nic)
 	} else
 		DPRINTK(HW, DEBUG, "phy_addr = %d\n", nic->mii.phy_id);
 
-	/* Isolate all the PHY ids */
-	for (addr = 0; addr < 32; addr++)
-		mdio_write(netdev, addr, MII_BMCR, BMCR_ISOLATE);
-	/* Select the discovered PHY */
-	bmcr &= ~BMCR_ISOLATE;
-	mdio_write(netdev, nic->mii.phy_id, MII_BMCR, bmcr);
-
 	/* Get phy ID */
 	id_lo = mdio_read(netdev, nic->mii.phy_id, MII_PHYSID1);
 	id_hi = mdio_read(netdev, nic->mii.phy_id, MII_PHYSID2);
 	nic->phy = (u32)id_hi << 16 | (u32)id_lo;
 	DPRINTK(HW, DEBUG, "phy ID = 0x%08X\n", nic->phy);
 
+	/* Select the phy and isolate the rest */
+	for (addr = 0; addr < 32; addr++) {
+		if (addr != nic->mii.phy_id) {
+			mdio_write(netdev, addr, MII_BMCR, BMCR_ISOLATE);
+		} else if (nic->phy != phy_82552_v) {
+			bmcr = mdio_read(netdev, addr, MII_BMCR);
+			mdio_write(netdev, addr, MII_BMCR,
+				bmcr & ~BMCR_ISOLATE);
+		}
+	}
+	/*
+	 * Workaround for 82552:
+	 * Clear the ISOLATE bit on selected phy_id last (mirrored on all
+	 * other phy_id's) using bmcr value from addr discovery loop above.
+	 */
+	if (nic->phy == phy_82552_v)
+		mdio_write(netdev, nic->mii.phy_id, MII_BMCR,
+			bmcr & ~BMCR_ISOLATE);
+
 	/* Handle National tx phys */
 #define NCS_PHY_MODEL_MASK	0xFFF0FFFF
 	if ((nic->phy & NCS_PHY_MODEL_MASK) == phy_nsc_tx) {
maintainer Applied
#1 lore raw

From: Jeff Kirsher <[email protected]>
Date: Thu, 29 Oct 2009 16:42:41 -0700

Quoted 12 lines

From: Bruce Allan <[email protected]>

A change in how PHYs are electrically isolated caused all PHYs to be isolated followed by reverting that isolation for the selected PHY. Unfortunately, isolating the selected PHY for even a short period of time can result in DHCP negotiation taking more than 10 seconds on certain embedded configurations delaying boot time as reported by Bernhard Kaindl. This patch reverts the change to how PHYs are isolated yet still works around the issue for 82552 needing the selected PHY's BMCR register to be written after the unused PHYs are isolated. This code is moved below the setting of nic->phy ID in order to do the 82552-specific workaround.

Quoted 3 lines

Applied.