Skip to contentSkip to conversation

igb: add support for the 82580 phy

PATCH Applied Jeff Kirsher 2 participants 5 messages Nov 19, 2009 – Nov 20, 2009

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/3 igb: add support for the 82580 phy

From: Alexander Duyck <[email protected]>

This patch adds support for the phy included in the 82580 silicon family.

---

 drivers/net/igb/e1000_hw.h  |    1 
 drivers/net/igb/e1000_phy.c |  242 +++++++++++++++++++++++++++++++++++++++++++
 drivers/net/igb/e1000_phy.h |   32 ++++++
 3 files changed, 275 insertions(+), 0 deletions(-)
drivers/net/igb/e1000_hw.h +1 -0
index 2dc9294..5deda3e 100644
@@ -93,6 +93,7 @@ enum e1000_phy_type {
 	e1000_phy_gg82563,
 	e1000_phy_igp_3,
 	e1000_phy_ife,
+	e1000_phy_82580,
 };
 
 enum e1000_bus_type {
drivers/net/igb/e1000_phy.c +242 -0

251 lines not on this page · raw message

drivers/net/igb/e1000_phy.h +32 -0
index adb9436..e23b021 100644
@@ -63,6 +63,11 @@ s32  igb_phy_has_link(struct e1000_hw *hw, u32 iterations,
 s32  igb_phy_init_script_igp3(struct e1000_hw *hw);
 s32  igb_read_phy_reg_i2c(struct e1000_hw *hw, u32 offset, u16 *data);
 s32  igb_write_phy_reg_i2c(struct e1000_hw *hw, u32 offset, u16 data);
+s32  igb_copper_link_setup_82580(struct e1000_hw *hw);
+s32  igb_check_polarity_82580(struct e1000_hw *hw);
+s32  igb_get_phy_info_82580(struct e1000_hw *hw);
+s32  igb_phy_force_speed_duplex_82580(struct e1000_hw *hw);
+s32  igb_get_cable_length_82580(struct e1000_hw *hw);
 
 /* IGP01E1000 Specific Registers */
 #define IGP01E1000_PHY_PORT_CONFIG        0x10 /* Port Config */
@@ -77,6 +82,33 @@ s32  igb_write_phy_reg_i2c(struct e1000_hw *hw, u32 offset, u16 data);
 #define IGP01E1000_PSCR_FORCE_MDI_MDIX    0x2000 /* 0=MDI, 1=MDIX */
 #define IGP01E1000_PSCFR_SMART_SPEED      0x0080
 
+#define I82580_ADDR_REG                   16
+#define I82580_CFG_REG                    22
+#define I82580_CFG_ASSERT_CRS_ON_TX       (1 << 15)
+#define I82580_CFG_ENABLE_DOWNSHIFT       (3 << 10) /* auto downshift 100/10 */
+#define I82580_CTRL_REG                   23
+#define I82580_CTRL_DOWNSHIFT_MASK        (7 << 10)
+
+/* 82580 specific PHY registers */
+#define I82580_PHY_CTRL_2            18
+#define I82580_PHY_LBK_CTRL          19
+#define I82580_PHY_STATUS_2          26
+#define I82580_PHY_DIAG_STATUS       31
+
+/* I82580 PHY Status 2 */
+#define I82580_PHY_STATUS2_REV_POLARITY   0x0400
+#define I82580_PHY_STATUS2_MDIX           0x0800
+#define I82580_PHY_STATUS2_SPEED_MASK     0x0300
+#define I82580_PHY_STATUS2_SPEED_1000MBPS 0x0200
+#define I82580_PHY_STATUS2_SPEED_100MBPS  0x0100
+
+/* I82580 PHY Control 2 */
+#define I82580_PHY_CTRL2_AUTO_MDIX        0x0400
+#define I82580_PHY_CTRL2_FORCE_MDI_MDIX   0x0200
+
+/* I82580 PHY Diagnostics Status */
+#define I82580_DSTATUS_CABLE_LENGTH       0x03FC
+#define I82580_DSTATUS_CABLE_LENGTH_SHIFT 2
 /* Enable flexible speed on link-up */
 #define IGP02E1000_PM_D0_LPLU             0x0002 /* For D0a states */
 #define IGP02E1000_PM_D3_LPLU             0x0004 /* For all other states */
#1 lore raw

PATCH 2/3 igb: add support for 82580 MAC

From: Alexander Duyck <[email protected]>

This patch adds support for the 82580 MAC.

---

 drivers/net/igb/e1000_82575.c   |  302 ++++++++++++++++++++++++++++++++++-----
 drivers/net/igb/e1000_82575.h   |    6 +
 drivers/net/igb/e1000_defines.h |   10 +
 drivers/net/igb/e1000_hw.h      |   13 ++
 drivers/net/igb/e1000_phy.c     |    6 -
 drivers/net/igb/e1000_phy.h     |    3 
 drivers/net/igb/e1000_regs.h    |    1 
 7 files changed, 299 insertions(+), 42 deletions(-)
drivers/net/igb/e1000_82575.c +266 -36
index 5d345e3..e8e9e91 100644
@@ -46,7 +46,10 @@ static s32  igb_get_cfg_done_82575(struct e1000_hw *);
 static s32  igb_init_hw_82575(struct e1000_hw *);
 static s32  igb_phy_hw_reset_sgmii_82575(struct e1000_hw *);
 static s32  igb_read_phy_reg_sgmii_82575(struct e1000_hw *, u32, u16 *);
+static s32  igb_read_phy_reg_82580(struct e1000_hw *, u32, u16 *);
+static s32  igb_write_phy_reg_82580(struct e1000_hw *, u32, u16);
 static s32  igb_reset_hw_82575(struct e1000_hw *);
+static s32  igb_reset_hw_82580(struct e1000_hw *);
 static s32  igb_set_d0_lplu_state_82575(struct e1000_hw *, bool);
 static s32  igb_setup_copper_link_82575(struct e1000_hw *);
 static s32  igb_setup_serdes_link_82575(struct e1000_hw *);
@@ -62,6 +65,12 @@ static s32  igb_reset_init_script_82575(struct e1000_hw *);
 static s32  igb_read_mac_addr_82575(struct e1000_hw *);
 static s32  igb_set_pcie_completion_timeout(struct e1000_hw *hw);
 
+static const u16 e1000_82580_rxpbs_table[] =
+	{ 36, 72, 144, 1, 2, 4, 8, 16,
+	  35, 70, 140 };
+#define E1000_82580_RXPBS_TABLE_SIZE \
+	(sizeof(e1000_82580_rxpbs_table)/sizeof(u16))
+
 static s32 igb_get_invariants_82575(struct e1000_hw *hw)
 {
 	struct e1000_phy_info *phy = &hw->phy;
@@ -88,6 +97,13 @@ static s32 igb_get_invariants_82575(struct e1000_hw *hw)
 	case E1000_DEV_ID_82576_SERDES_QUAD:
 		mac->type = e1000_82576;
 		break;
+	case E1000_DEV_ID_82580_COPPER:
+	case E1000_DEV_ID_82580_FIBER:
+	case E1000_DEV_ID_82580_SERDES:
+	case E1000_DEV_ID_82580_SGMII:
+	case E1000_DEV_ID_82580_COPPER_DUAL:
+		mac->type = e1000_82580;
+		break;
 	default:
 		return -E1000_ERR_MAC_INIT;
 		break;
@@ -110,6 +126,7 @@ static s32 igb_get_invariants_82575(struct e1000_hw *hw)
 		dev_spec->sgmii_active = true;
 		ctrl_ext |= E1000_CTRL_I2C_ENA;
 		break;
+	case E1000_CTRL_EXT_LINK_MODE_1000BASE_KX:
 	case E1000_CTRL_EXT_LINK_MODE_PCIE_SERDES:
 		hw->phy.media_type = e1000_media_type_internal_serdes;
 		ctrl_ext |= E1000_CTRL_I2C_ENA;
@@ -121,12 +138,26 @@ static s32 igb_get_invariants_82575(struct e1000_hw *hw)
 
 	wr32(E1000_CTRL_EXT, ctrl_ext);
 
+	/*
+	 * if using i2c make certain the MDICNFG register is cleared to prevent
+	 * communications from being misrouted to the mdic registers
+	 */
+	if ((ctrl_ext & E1000_CTRL_I2C_ENA) && (hw->mac.type == e1000_82580))
+		wr32(E1000_MDICNFG, 0);
+
 	/* Set mta register count */
 	mac->mta_reg_count = 128;
 	/* Set rar entry count */
 	mac->rar_entry_count = E1000_RAR_ENTRIES_82575;
 	if (mac->type == e1000_82576)
 		mac->rar_entry_count = E1000_RAR_ENTRIES_82576;
+	if (mac->type == e1000_82580)
+		mac->rar_entry_count = E1000_RAR_ENTRIES_82580;
+	/* reset */
+	if (mac->type == e1000_82580)
+		mac->ops.reset_hw = igb_reset_hw_82580;
+	else
+		mac->ops.reset_hw = igb_reset_hw_82575;
 	/* Set if part includes ASF firmware */
 	mac->asf_firmware_present = true;
 	/* Set if manageability features are enabled. */
@@ -194,6 +225,10 @@ static s32 igb_get_invariants_82575(struct e1000_hw *hw)
 		phy->ops.reset              = igb_phy_hw_reset_sgmii_82575;
 		phy->ops.read_reg           = igb_read_phy_reg_sgmii_82575;
 		phy->ops.write_reg          = igb_write_phy_reg_sgmii_82575;
+	} else if (hw->mac.type == e1000_82580) {
+		phy->ops.reset              = igb_phy_hw_reset;
+		phy->ops.read_reg           = igb_read_phy_reg_82580;
+		phy->ops.write_reg          = igb_write_phy_reg_82580;
 	} else {
 		phy->ops.reset              = igb_phy_hw_reset;
 		phy->ops.read_reg           = igb_read_phy_reg_igp;
@@ -225,6 +260,12 @@ static s32 igb_get_invariants_82575(struct e1000_hw *hw)
 		phy->ops.set_d0_lplu_state  = igb_set_d0_lplu_state_82575;
 		phy->ops.set_d3_lplu_state  = igb_set_d3_lplu_state;
 		break;
+	case I82580_I_PHY_ID:
+		phy->type                   = e1000_phy_82580;
+		phy->ops.force_speed_duplex = igb_phy_force_speed_duplex_82580;
+		phy->ops.get_cable_length   = igb_get_cable_length_82580;
+		phy->ops.get_phy_info       = igb_get_phy_info_82580;
+		break;
 	default:
 		return -E1000_ERR_PHY;
 	}
@@ -635,6 +676,10 @@ static s32 igb_get_cfg_done_82575(struct e1000_hw *hw)
 
 	if (hw->bus.func == 1)
 		mask = E1000_NVM_CFG_DONE_PORT_1;
+	else if (hw->bus.func == E1000_FUNC_2)
+		mask = E1000_NVM_CFG_DONE_PORT_2;
+	else if (hw->bus.func == E1000_FUNC_3)
+		mask = E1000_NVM_CFG_DONE_PORT_3;
 
 	while (timeout) {
 		if (rd32(E1000_EEMNGCTL) & mask)
@@ -754,6 +799,10 @@ void igb_shutdown_serdes_link_82575(struct e1000_hw *hw)
 
 	if (hw->bus.func == E1000_FUNC_0)
 		hw->nvm.ops.read(hw, NVM_INIT_CONTROL3_PORT_A, 1, &eeprom_data);
+	else if (hw->mac.type == e1000_82580)
+		hw->nvm.ops.read(hw, NVM_INIT_CONTROL3_PORT_A +
+		                 NVM_82580_LAN_FUNC_OFFSET(hw->bus.func), 1,
+		                 &eeprom_data);
 	else if (hw->bus.func == E1000_FUNC_1)
 		hw->nvm.ops.read(hw, NVM_INIT_CONTROL3_PORT_B, 1, &eeprom_data);
 
@@ -918,6 +967,9 @@ static s32 igb_setup_copper_link_82575(struct e1000_hw *hw)
 		goto out;
 
 	if (igb_sgmii_active_82575(hw) && !hw->phy.reset_disable) {
+		/* allow time for SFP cage time to power up phy */
+		msleep(300);
+
 		ret_val = hw->phy.ops.reset(hw);
 		if (ret_val) {
 			hw_dbg("Error resetting the PHY.\n");
@@ -931,6 +983,9 @@ static s32 igb_setup_copper_link_82575(struct e1000_hw *hw)
 	case e1000_phy_igp_3:
 		ret_val = igb_copper_link_setup_igp(hw);
 		break;
+	case e1000_phy_82580:
+		ret_val = igb_copper_link_setup_82580(hw);
+		break;
 	default:
 		ret_val = -E1000_ERR_PHY;
 		break;
@@ -955,7 +1010,8 @@ out:
  **/
 static s32 igb_setup_serdes_link_82575(struct e1000_hw *hw)
 {
-	u32 ctrl_reg, reg;
+	u32 ctrl_ext, ctrl_reg, reg;
+	bool pcs_autoneg;
 
 	if ((hw->phy.media_type != e1000_media_type_internal_serdes) &&
 	    !igb_sgmii_active_82575(hw))
@@ -970,9 +1026,9 @@ static s32 igb_setup_serdes_link_82575(struct e1000_hw *hw)
 	wr32(E1000_SCTL, E1000_SCTL_DISABLE_SERDES_LOOPBACK);
 
 	/* power on the sfp cage if present */
-	reg = rd32(E1000_CTRL_EXT);
-	reg &= ~E1000_CTRL_EXT_SDP3_DATA;
-	wr32(E1000_CTRL_EXT, reg);
+	ctrl_ext = rd32(E1000_CTRL_EXT);
+	ctrl_ext &= ~E1000_CTRL_EXT_SDP3_DATA;
+	wr32(E1000_CTRL_EXT, ctrl_ext);
 
 	ctrl_reg = rd32(E1000_CTRL);
 	ctrl_reg |= E1000_CTRL_SLU;
@@ -989,15 +1045,31 @@ static s32 igb_setup_serdes_link_82575(struct e1000_hw *hw)
 
 	reg = rd32(E1000_PCS_LCTL);
 
-	if (igb_sgmii_active_82575(hw)) {
-		/* allow time for SFP cage to power up phy */
-		msleep(300);
+	/* default pcs_autoneg to the same setting as mac autoneg */
+	pcs_autoneg = hw->mac.autoneg;
 
-		/* AN time out should be disabled for SGMII mode */
+	switch (ctrl_ext & E1000_CTRL_EXT_LINK_MODE_MASK) {
+	case E1000_CTRL_EXT_LINK_MODE_SGMII:
+		/* sgmii mode lets the phy handle forcing speed/duplex */
+		pcs_autoneg = true;
+		/* autoneg time out should be disabled for SGMII mode */
 		reg &= ~(E1000_PCS_LCTL_AN_TIMEOUT);
-	} else {
+		break;
+	case E1000_CTRL_EXT_LINK_MODE_1000BASE_KX:
+		/* disable PCS autoneg and support parallel detect only */
+		pcs_autoneg = false;
+	default:
+		/*
+		 * non-SGMII modes only supports a speed of 1000/Full for the
+		 * link so it is best to just force the MAC and let the pcs
+		 * link either autoneg or be forced to 1000/Full
+		 */
 		ctrl_reg |= E1000_CTRL_SPD_1000 | E1000_CTRL_FRCSPD |
 		            E1000_CTRL_FD | E1000_CTRL_FRCDPX;
+
+		/* set speed of 1000/Full if speed/duplex is forced */
+		reg |= E1000_PCS_LCTL_FSV_1000 | E1000_PCS_LCTL_FDV_FULL;
+		break;
 	}
 
 	wr32(E1000_CTRL, ctrl_reg);
@@ -1008,7 +1080,6 @@ static s32 igb_setup_serdes_link_82575(struct e1000_hw *hw)
 	 * mode that will be compatible with older link partners and switches.
 	 * However, both are supported by the hardware and some drivers/tools.
 	 */
-
 	reg &= ~(E1000_PCS_LCTL_AN_ENABLE | E1000_PCS_LCTL_FLV_LINK_UP |
 		E1000_PCS_LCTL_FSD | E1000_PCS_LCTL_FORCE_LINK);
 
@@ -1018,34 +1089,18 @@ static s32 igb_setup_serdes_link_82575(struct e1000_hw *hw)
 	 */
 	reg |= E1000_PCS_LCTL_FORCE_FCTRL;
 
-	/*
-	 * we always set sgmii to autoneg since it is the phy that will be
-	 * forcing the link and the serdes is just a go-between
-	 */
-	if (hw->mac.autoneg || igb_sgmii_active_82575(hw)) {
+	if (pcs_autoneg) {
 		/* Set PCS register for autoneg */
-		reg |= E1000_PCS_LCTL_FSV_1000 |  /* Force 1000 */
-		       E1000_PCS_LCTL_FDV_FULL |  /* SerDes Full dplx */
-		       E1000_PCS_LCTL_AN_ENABLE | /* Enable Autoneg */
+		reg |= E1000_PCS_LCTL_AN_ENABLE | /* Enable Autoneg */
 		       E1000_PCS_LCTL_AN_RESTART; /* Restart autoneg */
-		hw_dbg("Configuring Autoneg; PCS_LCTL = 0x%08X\n", reg);
+		hw_dbg("Configuring Autoneg:PCS_LCTL=0x%08X\n", reg);
 	} else {
-		/* Check for duplex first */
-		if (hw->mac.forced_speed_duplex & E1000_ALL_FULL_DUPLEX)
-			reg |= E1000_PCS_LCTL_FDV_FULL;
-
-		/* No need to check for 1000/full since the spec states that
-		 * it requires autoneg to be enabled */
-		/* Now set speed */
-		if (hw->mac.forced_speed_duplex & E1000_ALL_100_SPEED)
-			reg |= E1000_PCS_LCTL_FSV_100;
-
-		/* Force speed and force link */
-		reg |= E1000_PCS_LCTL_FSD |
-		       E1000_PCS_LCTL_FORCE_LINK |
-		       E1000_PCS_LCTL_FLV_LINK_UP;
-
-		hw_dbg("Configuring Forced Link; PCS_LCTL = 0x%08X\n", reg);
+		/* Set PCS register for forced link */
+		reg |= E1000_PCS_LCTL_FSD |        /* Force Speed */
+		       E1000_PCS_LCTL_FORCE_LINK | /* Force Link */
+		       E1000_PCS_LCTL_FLV_LINK_UP; /* Force link value up */
+
+		hw_dbg("Configuring Forced Link:PCS_LCTL=0x%08X\n", reg);
 	}
 
 	wr32(E1000_PCS_LCTL, reg);
@@ -1354,8 +1409,183 @@ void igb_vmdq_set_replication_pf(struct e1000_hw *hw, bool enable)
 	wr32(E1000_VT_CTL, vt_ctl);
 }
 
+/**
+ *  igb_read_phy_reg_82580 - Read 82580 MDI control register
+ *  @hw: pointer to the HW structure
+ *  @offset: register offset to be read
+ *  @data: pointer to the read data
+ *
+ *  Reads the MDI control register in the PHY at offset and stores the
+ *  information read to data.
+ **/
+static s32 igb_read_phy_reg_82580(struct e1000_hw *hw, u32 offset, u16 *data)
+{
+	u32 mdicnfg = 0;
+	s32 ret_val;
+
+
+	ret_val = hw->phy.ops.acquire(hw);
+	if (ret_val)
+		goto out;
+
+	/*
+	 * We config the phy address in MDICNFG register now. Same bits
+	 * as before. The values in MDIC can be written but will be
+	 * ignored. This allows us to call the old function after
+	 * configuring the PHY address in the new register
+	 */
+	mdicnfg = (hw->phy.addr << E1000_MDIC_PHY_SHIFT);
+	wr32(E1000_MDICNFG, mdicnfg);
+
+	ret_val = igb_read_phy_reg_mdic(hw, offset, data);
+
+	hw->phy.ops.release(hw);
+
+out:
+	return ret_val;
+}
+
+/**
+ *  igb_write_phy_reg_82580 - Write 82580 MDI control register
+ *  @hw: pointer to the HW structure
+ *  @offset: register offset to write to
+ *  @data: data to write to register at offset
+ *
+ *  Writes data to MDI control register in the PHY at offset.
+ **/
+static s32 igb_write_phy_reg_82580(struct e1000_hw *hw, u32 offset, u16 data)
+{
+	u32 mdicnfg = 0;
+	s32 ret_val;
+
+
+	ret_val = hw->phy.ops.acquire(hw);
+	if (ret_val)
+		goto out;
+
+	/*
+	 * We config the phy address in MDICNFG register now. Same bits
+	 * as before. The values in MDIC can be written but will be
+	 * ignored. This allows us to call the old function after
+	 * configuring the PHY address in the new register
+	 */
+	mdicnfg = (hw->phy.addr << E1000_MDIC_PHY_SHIFT);
+	wr32(E1000_MDICNFG, mdicnfg);
+
+	ret_val = igb_write_phy_reg_mdic(hw, offset, data);
+
+	hw->phy.ops.release(hw);
+
+out:
+	return ret_val;
+}
+
+/**
+ *  igb_reset_hw_82580 - Reset hardware
+ *  @hw: pointer to the HW structure
+ *
+ *  This resets function or entire device (all ports, etc.)
+ *  to a known state.
+ **/
+static s32 igb_reset_hw_82580(struct e1000_hw *hw)
+{
+	s32 ret_val = 0;
+	/* BH SW mailbox bit in SW_FW_SYNC */
+	u16 swmbsw_mask = E1000_SW_SYNCH_MB;
+	u32 ctrl, icr;
+	bool global_device_reset = hw->dev_spec._82575.global_device_reset;
+
+
+	hw->dev_spec._82575.global_device_reset = false;
+
+	/* Get current control state. */
+	ctrl = rd32(E1000_CTRL);
+
+	/*
+	 * Prevent the PCI-E bus from sticking if there is no TLP connection
+	 * on the last TLP read/write transaction when MAC is reset.
+	 */
+	ret_val = igb_disable_pcie_master(hw);
+	if (ret_val)
+		hw_dbg("PCI-E Master disable polling has failed.\n");
+
+	hw_dbg("Masking off all interrupts\n");
+	wr32(E1000_IMC, 0xffffffff);
+	wr32(E1000_RCTL, 0);
+	wr32(E1000_TCTL, E1000_TCTL_PSP);
+	wrfl();
+
+	msleep(10);
+
+	/* Determine whether or not a global dev reset is requested */
+	if (global_device_reset &&
+		igb_acquire_swfw_sync_82575(hw, swmbsw_mask))
+			global_device_reset = false;
+
+	if (global_device_reset &&
+		!(rd32(E1000_STATUS) & E1000_STAT_DEV_RST_SET))
+		ctrl |= E1000_CTRL_DEV_RST;
+	else
+		ctrl |= E1000_CTRL_RST;
+
+	wr32(E1000_CTRL, ctrl);
+
+	/* Add delay to insure DEV_RST has time to complete */
+	if (global_device_reset)
+		msleep(5);
+
+	ret_val = igb_get_auto_rd_done(hw);
+	if (ret_val) {
+		/*
+		 * When auto config read does not complete, do not
+		 * return with an error. This can happen in situations
+		 * where there is no eeprom and prevents getting link.
+		 */
+		hw_dbg("Auto Read Done did not complete\n");
+	}
+
+	/* If EEPROM is not present, run manual init scripts */
+	if ((rd32(E1000_EECD) & E1000_EECD_PRES) == 0)
+		igb_reset_init_script_82575(hw);
+
+	/* clear global device reset status bit */
+	wr32(E1000_STATUS, E1000_STAT_DEV_RST_SET);
+
+	/* Clear any pending interrupt events. */
+	wr32(E1000_IMC, 0xffffffff);
+	icr = rd32(E1000_ICR);
+
+	/* Install any alternate MAC address into RAR0 */
+	ret_val = igb_check_alt_mac_addr(hw);
+
+	/* Release semaphore */
+	if (global_device_reset)
+		igb_release_swfw_sync_82575(hw, swmbsw_mask);
+
+	return ret_val;
+}
+
+/**
+ *  igb_rxpbs_adjust_82580 - adjust RXPBS value to reflect actual RX PBA size
+ *  @data: data received by reading RXPBS register
+ *
+ *  The 82580 uses a table based approach for packet buffer allocation sizes.
+ *  This function converts the retrieved value into the correct table value
+ *     0x0 0x1 0x2 0x3 0x4 0x5 0x6 0x7
+ *  0x0 36  72 144   1   2   4   8  16
+ *  0x8 35  70 140 rsv rsv rsv rsv rsv
+ */
+u16 igb_rxpbs_adjust_82580(u32 data)
+{
+	u16 ret_val = 0;
+
+	if (data < E1000_82580_RXPBS_TABLE_SIZE)
+		ret_val = e1000_82580_rxpbs_table[data];
+
+	return ret_val;
+}
+
 static struct e1000_mac_operations e1000_mac_ops_82575 = {
-	.reset_hw             = igb_reset_hw_82575,
 	.init_hw              = igb_init_hw_82575,
 	.check_for_link       = igb_check_for_link_82575,
 	.rar_set              = igb_rar_set,
drivers/net/igb/e1000_82575.h +6 -0
index b3808ca..d51c992 100644
@@ -38,6 +38,11 @@ extern void igb_rx_fifo_flush_82575(struct e1000_hw *hw);
 
 #define E1000_RAR_ENTRIES_82575   16
 #define E1000_RAR_ENTRIES_82576   24
+#define E1000_RAR_ENTRIES_82580   24
+
+#define E1000_SW_SYNCH_MB              0x00000100
+#define E1000_STAT_DEV_RST_SET         0x00100000
+#define E1000_CTRL_DEV_RST             0x20000000
 
 /* SRRCTL bit definitions */
 #define E1000_SRRCTL_BSIZEPKT_SHIFT                     10 /* Shift _right_ */
@@ -232,5 +237,6 @@ struct e1000_adv_tx_context_desc {
 #define E1000_RXPBS_SIZE_MASK_82576  0x0000007F
 void igb_vmdq_set_loopback_pf(struct e1000_hw *, bool);
 void igb_vmdq_set_replication_pf(struct e1000_hw *, bool);
+u16 igb_rxpbs_adjust_82580(u32 data);
 
 #endif
drivers/net/igb/e1000_defines.h +8 -2
index 48fcab0..c58c4fd 100644
@@ -49,6 +49,7 @@
 #define E1000_CTRL_EXT_PFRSTD    0x00004000
 #define E1000_CTRL_EXT_LINK_MODE_MASK 0x00C00000
 #define E1000_CTRL_EXT_LINK_MODE_PCIE_SERDES  0x00C00000
+#define E1000_CTRL_EXT_LINK_MODE_1000BASE_KX  0x00400000
 #define E1000_CTRL_EXT_LINK_MODE_SGMII   0x00800000
 #define E1000_CTRL_EXT_EIAME          0x01000000
 #define E1000_CTRL_EXT_IRCA           0x00000001
@@ -557,8 +558,12 @@
 #define NVM_ALT_MAC_ADDR_PTR       0x0037
 #define NVM_CHECKSUM_REG           0x003F
 
-#define E1000_NVM_CFG_DONE_PORT_0  0x40000 /* MNG config cycle done */
-#define E1000_NVM_CFG_DONE_PORT_1  0x80000 /* ...for second port */
+#define E1000_NVM_CFG_DONE_PORT_0  0x040000 /* MNG config cycle done */
+#define E1000_NVM_CFG_DONE_PORT_1  0x080000 /* ...for second port */
+#define E1000_NVM_CFG_DONE_PORT_2  0x100000 /* ...for third port */
+#define E1000_NVM_CFG_DONE_PORT_3  0x200000 /* ...for fourth port */
+
+#define NVM_82580_LAN_FUNC_OFFSET(a) (a ? (0x40 + (0x40 * a)) : 0)
 
 /* Mask bits for fields in Word 0x0f of the NVM */
 #define NVM_WORD0F_PAUSE_MASK       0x3000
@@ -625,6 +630,7 @@
  */
 #define M88E1111_I_PHY_ID    0x01410CC0
 #define IGP03E1000_E_PHY_ID  0x02A80390
+#define I82580_I_PHY_ID      0x015403A0
 #define M88_VENDOR           0x0141
 
 /* M88E1000 Specific Registers */
drivers/net/igb/e1000_hw.h +13 -0
index 5deda3e..dbaeb5f 100644
@@ -47,19 +47,30 @@ struct e1000_hw;
 #define E1000_DEV_ID_82575EB_COPPER           0x10A7
 #define E1000_DEV_ID_82575EB_FIBER_SERDES     0x10A9
 #define E1000_DEV_ID_82575GB_QUAD_COPPER      0x10D6
+#define E1000_DEV_ID_82580_COPPER             0x150E
+#define E1000_DEV_ID_82580_FIBER              0x150F
+#define E1000_DEV_ID_82580_SERDES             0x1510
+#define E1000_DEV_ID_82580_SGMII              0x1511
+#define E1000_DEV_ID_82580_COPPER_DUAL        0x1516
 
 #define E1000_REVISION_2 2
 #define E1000_REVISION_4 4
 
 #define E1000_FUNC_0     0
 #define E1000_FUNC_1     1
+#define E1000_FUNC_2     2
+#define E1000_FUNC_3     3
 
+#define E1000_ALT_MAC_ADDRESS_OFFSET_LAN0   0
 #define E1000_ALT_MAC_ADDRESS_OFFSET_LAN1   3
+#define E1000_ALT_MAC_ADDRESS_OFFSET_LAN2   6
+#define E1000_ALT_MAC_ADDRESS_OFFSET_LAN3   9
 
 enum e1000_mac_type {
 	e1000_undefined = 0,
 	e1000_82575,
 	e1000_82576,
+	e1000_82580,
 	e1000_num_macs  /* List is 1-based, so subtract 1 for true count. */
 };
 
@@ -290,6 +301,7 @@ struct e1000_mac_operations {
 
 struct e1000_phy_operations {
 	s32  (*acquire)(struct e1000_hw *);
+	s32  (*check_polarity)(struct e1000_hw *);
 	s32  (*check_reset_block)(struct e1000_hw *);
 	s32  (*force_speed_duplex)(struct e1000_hw *);
 	s32  (*get_cfg_done)(struct e1000_hw *hw);
@@ -466,6 +478,7 @@ struct e1000_mbx_info {
 
 struct e1000_dev_spec_82575 {
 	bool sgmii_active;
+	bool global_device_reset;
 };
 
 struct e1000_hw {
drivers/net/igb/e1000_phy.c +3 -3
index b8fbc85..5c9d73e 100644
@@ -136,7 +136,7 @@ out:
  *  Reads the MDI control regsiter in the PHY at offset and stores the
  *  information read to data.
  **/
-static s32 igb_read_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 *data)
+s32 igb_read_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 *data)
 {
 	struct e1000_phy_info *phy = &hw->phy;
 	u32 i, mdic = 0;
@@ -194,7 +194,7 @@ out:
  *
  *  Writes data to MDI control register in the PHY at offset.
  **/
-static s32 igb_write_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 data)
+s32 igb_write_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 data)
 {
 	struct e1000_phy_info *phy = &hw->phy;
 	u32 i, mdic = 0;
@@ -1947,7 +1947,7 @@ s32 igb_phy_init_script_igp3(struct e1000_hw *hw)
  *
  *  Polarity is determined based on the PHY specific status register.
  **/
-s32 igb_check_polarity_82580(struct e1000_hw *hw)
+static s32 igb_check_polarity_82580(struct e1000_hw *hw)
 {
 	struct e1000_phy_info *phy = &hw->phy;
 	s32 ret_val;
drivers/net/igb/e1000_phy.h +2 -1
index e23b021..555eb54 100644
@@ -61,10 +61,11 @@ s32  igb_write_phy_reg_igp(struct e1000_hw *hw, u32 offset, u16 data);
 s32  igb_phy_has_link(struct e1000_hw *hw, u32 iterations,
 				u32 usec_interval, bool *success);
 s32  igb_phy_init_script_igp3(struct e1000_hw *hw);
+s32  igb_read_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 *data);
+s32  igb_write_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 data);
 s32  igb_read_phy_reg_i2c(struct e1000_hw *hw, u32 offset, u16 *data);
 s32  igb_write_phy_reg_i2c(struct e1000_hw *hw, u32 offset, u16 data);
 s32  igb_copper_link_setup_82580(struct e1000_hw *hw);
-s32  igb_check_polarity_82580(struct e1000_hw *hw);
 s32  igb_get_phy_info_82580(struct e1000_hw *hw);
 s32  igb_phy_force_speed_duplex_82580(struct e1000_hw *hw);
 s32  igb_get_cable_length_82580(struct e1000_hw *hw);
drivers/net/igb/e1000_regs.h +1 -0
index 934e03b..409c44b 100644
@@ -34,6 +34,7 @@
 #define E1000_EERD     0x00014  /* EEPROM Read - RW */
 #define E1000_CTRL_EXT 0x00018  /* Extended Device Control - RW */
 #define E1000_MDIC     0x00020  /* MDI Control - RW */
+#define E1000_MDICNFG  0x00E04  /* MDI Config - RW */
 #define E1000_SCTL     0x00024  /* SerDes Control - RW */
 #define E1000_FCAL     0x00028  /* Flow Control Address Low - RW */
 #define E1000_FCAH     0x0002C  /* Flow Control Address High -RW */
#2 lore raw

PATCH 3/3 igb: Add full support for 82580 devices

In reply to Jeff Kirsher

From: Alexander Duyck <[email protected]>

This patch makes use of the 82580 PHY and MAC support added and adds a set of supported device IDs for said hardware.

---

 drivers/net/igb/e1000_defines.h |    7 ++
 drivers/net/igb/e1000_regs.h    |    4 +
 drivers/net/igb/igb.h           |    1 
 drivers/net/igb/igb_ethtool.c   |   53 ++++++++++++++++
 drivers/net/igb/igb_main.c      |  131 ++++++++++++++++++++++++++++++++++++++-
 5 files changed, 193 insertions(+), 3 deletions(-)
drivers/net/igb/e1000_defines.h +7 -0
index c58c4fd..6e036ae 100644
@@ -330,6 +330,7 @@
 #define E1000_ICR_RXDMT0        0x00000010 /* rx desc min. threshold (0) */
 #define E1000_ICR_RXT0          0x00000080 /* rx timer intr (ring 0) */
 #define E1000_ICR_VMMB          0x00000100 /* VM MB event */
+#define E1000_ICR_DRSTA         0x40000000 /* Device Reset Asserted */
 /* If this bit asserted, the driver should claim the interrupt */
 #define E1000_ICR_INT_ASSERTED  0x80000000
 /* LAN connected device generates an interrupt */
@@ -371,6 +372,7 @@
 #define E1000_IMS_RXSEQ     E1000_ICR_RXSEQ     /* rx sequence error */
 #define E1000_IMS_RXDMT0    E1000_ICR_RXDMT0    /* rx desc min. threshold */
 #define E1000_IMS_RXT0      E1000_ICR_RXT0      /* rx timer intr */
+#define E1000_IMS_DRSTA     E1000_ICR_DRSTA     /* Device Reset Asserted */
 #define E1000_IMS_DOUTSYNC  E1000_ICR_DOUTSYNC /* NIC DMA out of sync */
 
 /* Extended Interrupt Mask Set */
@@ -379,6 +381,7 @@
 /* Interrupt Cause Set */
 #define E1000_ICS_LSC       E1000_ICR_LSC       /* Link Status Change */
 #define E1000_ICS_RXDMT0    E1000_ICR_RXDMT0    /* rx desc min. threshold */
+#define E1000_ICS_DRSTA     E1000_ICR_DRSTA     /* Device Reset Aserted */
 
 /* Extended Interrupt Cause Set */
 
@@ -717,4 +720,8 @@
 #define E1000_VFTA_ENTRY_MASK                0x7F
 #define E1000_VFTA_ENTRY_BIT_SHIFT_MASK      0x1F
 
+/* DMA Coalescing register fields */
+#define E1000_PCIEMISC_LX_DECISION      0x00000080 /* Lx power decision based
+                                                      on DMA coal */
+
 #endif
drivers/net/igb/e1000_regs.h +4 -0
index 409c44b..dd4e6ff 100644
@@ -89,6 +89,8 @@
 #define E1000_SYSTIML    0x0B600 /* System time register Low - RO */
 #define E1000_SYSTIMH    0x0B604 /* System time register High - RO */
 #define E1000_TIMINCA    0x0B608 /* Increment attributes register - RW */
+#define E1000_TSAUXC     0x0B640 /* Timesync Auxiliary Control register */
+#define E1000_SYSTIMR    0x0B6F8 /* System time register Residue */
 
 /* Filtering Registers */
 #define E1000_SAQF(_n) (0x5980 + 4 * (_n))
@@ -318,4 +320,6 @@
 #define array_rd32(reg, offset) \
 	(readl(hw->hw_addr + reg + ((offset) << 2)))
 
+/* DMA Coalescing registers */
+#define E1000_PCIEMISC          0x05BB8 /* PCIE misc config register */
 #endif
drivers/net/igb/igb.h +1 -0
index 63abd1c..c458d9b 100644
@@ -320,6 +320,7 @@ struct igb_adapter {
 #define IGB_FLAG_QUEUE_PAIRS       (1 << 3)
 
 #define IGB_82576_TSYNC_SHIFT 19
+#define IGB_82580_TSYNC_SHIFT 24
 enum e1000_state_t {
 	__IGB_TESTING,
 	__IGB_RESETTING,
drivers/net/igb/igb_ethtool.c +53 -0

77 lines not on this page · raw message

drivers/net/igb/igb_main.c +128 -3

223 lines not on this page · raw message