Skip to contentSkip to conversation

NET: Move MDIO regs out of TSEC Space

PATCH Superseded Sandeep Gopalpet 3 participants 4 messages Oct 24, 2009 – Dec 3, 2009 Network drivers

v2 of 4 Superseded Latest is v4 →

lore
Share & tools
lore
#0 lore raw

PATCH v2 1/2 NET: Move MDIO regs out of TSEC Space

Moved the mdio regs out of the tsec structure,and provided different offsets for tsec base and mdio base so that provision for etsec2.0 can be provided.

This patch helps in providing the support for etsec2.0 In etsec2.0, the MDIO register space and the etsec reg space are different.

Also, moved the TSEC_BASE_ADDR and MDIO_BASE_ADDR definitons into platform specific files.

---
 drivers/net/tsec.c           |   20 +++++++++---------
 include/asm-ppc/immap_83xx.h |    9 ++++++++
 include/asm-ppc/immap_85xx.h |   10 +++++++++
 include/asm-ppc/immap_86xx.h |    9 ++++++++
 include/tsec.h               |   43 +++++++++++++++++++----------------------
 5 files changed, 58 insertions(+), 33 deletions(-)
drivers/net/tsec.c +10 -10
index 5c3d261..2ad033e 100644
@@ -83,7 +83,7 @@ static struct tsec_info_struct tsec_info[] = {
 #ifdef CONFIG_MPC85XX_FEC
 	{
 		.regs = (tsec_t *)(TSEC_BASE_ADDR + 0x2000),
-		.miiregs = (tsec_t *)(TSEC_BASE_ADDR),
+		.miiregs = (tsec_mdio_t *)(MDIO_BASE_ADDR),
 		.devname = CONFIG_MPC85XX_FEC_NAME,
 		.phyaddr = FEC_PHY_ADDR,
 		.flags = FEC_FLAGS
@@ -136,6 +136,7 @@ int tsec_initialize(bd_t * bis, struct tsec_info_struct *tsec_info)
 	privlist[num_tsecs++] = priv;
 	priv->regs = tsec_info->regs;
 	priv->phyregs = tsec_info->miiregs;
+	priv->phyregs_sgmii = tsec_info->miiregs_sgmii;
 
 	priv->phyaddr = tsec_info->phyaddr;
 	priv->flags = tsec_info->flags;
@@ -222,7 +223,7 @@ int tsec_init(struct eth_device *dev, bd_t * bd)
 }
 
 /* Writes the given phy's reg with value, using the specified MDIO regs */
-static void tsec_local_mdio_write(volatile tsec_t *phyregs, uint addr,
+static void tsec_local_mdio_write(volatile tsec_mdio_t *phyregs, uint addr,
 		uint reg, uint value)
 {
 	int timeout = 1000000;
@@ -245,7 +246,7 @@ static void tsec_local_mdio_write(volatile tsec_t *phyregs, uint addr,
  * notvalid bit cleared), and the bus to cease activity (miimind
  * busy bit cleared), and then returns the value
  */
-uint tsec_local_mdio_read(volatile tsec_t *phyregs, uint phyid, uint regnum)
+uint tsec_local_mdio_read(volatile tsec_mdio_t *phyregs, uint phyid, uint regnum)
 {
 	uint value;
 
@@ -290,11 +291,11 @@ static void tsec_configure_serdes(struct tsec_private *priv)
 {
 	/* Access TBI PHY registers at given TSEC register offset as opposed to the
 	 * register offset used for external PHY accesses */
-	tsec_local_mdio_write(priv->regs, priv->regs->tbipa, TBI_ANA,
+	tsec_local_mdio_write(priv->phyregs_sgmii, priv->regs->tbipa, TBI_ANA,
 			TBIANA_SETTINGS);
-	tsec_local_mdio_write(priv->regs, priv->regs->tbipa, TBI_TBICON,
+	tsec_local_mdio_write(priv->phyregs_sgmii, priv->regs->tbipa, TBI_TBICON,
 			TBICON_CLK_SELECT);
-	tsec_local_mdio_write(priv->regs, priv->regs->tbipa, TBI_CR,
+	tsec_local_mdio_write(priv->phyregs_sgmii, priv->regs->tbipa, TBI_CR,
 			TBICR_SETTINGS);
 }
 
@@ -306,12 +307,11 @@ static int init_phy(struct eth_device *dev)
 {
 	struct tsec_private *priv = (struct tsec_private *)dev->priv;
 	struct phy_info *curphy;
-	volatile tsec_t *phyregs = priv->phyregs;
+	volatile tsec_mdio_t *phyregs = priv->phyregs;
 	volatile tsec_t *regs = priv->regs;
 
 	/* Assign a Physical address to the TBI */
 	regs->tbipa = CONFIG_SYS_TBIPA_VALUE;
-	phyregs->tbipa = CONFIG_SYS_TBIPA_VALUE;
 	asm("sync");
 
 	/* Reset MII (due to new addresses) */
@@ -739,7 +739,7 @@ uint mii_parse_dm9161_scsr(uint mii_reg, struct tsec_private * priv)
 uint mii_cis8204_fixled(uint mii_reg, struct tsec_private * priv)
 {
 	uint phyid;
-	volatile tsec_t *regbase = priv->phyregs;
+	volatile tsec_mdio_t *regbase = priv->phyregs;
 	int timeout = 1000000;
 
 	for (phyid = 0; phyid < 4; phyid++) {
@@ -1772,7 +1772,7 @@ void phy_run_commands(struct tsec_private *priv, struct phy_cmd *cmd)
 {
 	int i;
 	uint result;
-	volatile tsec_t *phyregs = priv->phyregs;
+	volatile tsec_mdio_t *phyregs = priv->phyregs;
 
 	phyregs->miimcfg = MIIMCFG_RESET;
 
include/asm-ppc/immap_83xx.h +9 -0
index c60a7d2..57b1a72 100644
@@ -868,4 +868,13 @@ typedef struct immap {
 #endif
 #define CONFIG_SYS_MPC83xx_USB_ADDR \
 			(CONFIG_SYS_IMMR + CONFIG_SYS_MPC83xx_USB_OFFSET)
+
+#define CONFIG_SYS_TSEC1_OFFSET		0x24000
+#define TSEC_SIZE			0x01000
+
+#define CONFIG_SYS_MDIO1_OFFSET		0x24520
+#define MDIO_OFFSET			0x01000
+
+#define TSEC_BASE_ADDR		(CONFIG_SYS_IMMR + CONFIG_SYS_TSEC1_OFFSET)
+#define MDIO_BASE_ADDR		(CONFIG_SYS_IMMR + CONFIG_SYS_MDIO1_OFFSET)
 #endif				/* __IMMAP_83xx__ */
include/asm-ppc/immap_85xx.h +10 -0
index 4194295..ad3910c 100644
@@ -1932,4 +1932,14 @@ typedef struct ccsr_gur {
 #define CONFIG_SYS_MPC85xx_USB_ADDR \
 	(CONFIG_SYS_IMMR + CONFIG_SYS_MPC85xx_USB_OFFSET)
 
+/* TSEC and MDIO OFFSETS */
+#define CONFIG_SYS_TSEC1_OFFSET		0x24000
+#define TSEC_SIZE			0x01000
+
+#define CONFIG_SYS_MDIO1_OFFSET		0x24520
+#define MDIO_OFFSET			0x01000
+
+#define TSEC_BASE_ADDR		(CONFIG_SYS_IMMR + CONFIG_SYS_TSEC1_OFFSET)
+#define MDIO_BASE_ADDR		(CONFIG_SYS_IMMR + CONFIG_SYS_MDIO1_OFFSET)
+
 #endif /*__IMMAP_85xx__*/
include/asm-ppc/immap_86xx.h +9 -0
index fdfc654..80e7ecd 100644
@@ -1298,4 +1298,13 @@ extern immap_t  *immr;
 #define CONFIG_SYS_MPC86xx_DMA_OFFSET	(0x21000)
 #define CONFIG_SYS_MPC86xx_DMA_ADDR	(CONFIG_SYS_IMMR + CONFIG_SYS_MPC86xx_DMA_OFFSET)
 
+#define CONFIG_SYS_TSEC1_OFFSET		0x24000
+#define TSEC_SIZE			0x01000
+
+#define CONFIG_SYS_MDIO1_OFFSET		0x24520
+#define MDIO_OFFSET			0x01000
+
+#define TSEC_BASE_ADDR		(CONFIG_SYS_IMMR + CONFIG_SYS_TSEC1_OFFSET)
+#define MDIO_BASE_ADDR		(CONFIG_SYS_IMMR + CONFIG_SYS_MDIO1_OFFSET)
+
 #endif /*__IMMAP_86xx__*/
include/tsec.h +20 -23

88 lines not on this page · raw message

Signature · 1 line
1.5.2.2
#1 lore raw

PATCH v2 1/2 NET: Move MDIO regs out of TSEC Space

Quoted 12 lines · Sandeep Gopalpet

Moved the mdio regs out of the tsec structure,and provided different offsets for tsec base and mdio base so that provision for etsec2.0 can be provided.

This patch helps in providing the support for etsec2.0 In etsec2.0, the MDIO register space and the etsec reg space are different.

Also, moved the TSEC_BASE_ADDR and MDIO_BASE_ADDR definitons into platform specific files.

Quoted 8 lines

---

drivers/net/tsec.c           |   20 +++++++++---------
include/asm-ppc/immap_83xx.h |    9 ++++++++
include/asm-ppc/immap_85xx.h |   10 +++++++++
include/asm-ppc/immap_86xx.h |    9 ++++++++
include/tsec.h               |   43 ++++++++++++++++++ 
+----------------------
5 files changed, 58 insertions(+), 33 deletions(-)

Kim,

Can you ack this and I'll pick it via the 85xx tree.

- k

Quoted 269 lines
drivers/net/tsec.c +2 -1
index 5c3d261..2ad033e 100644
@@ -83,7 +83,7 @@ static struct tsec_info_struct tsec_info[] = {
 #ifdef CONFIG_MPC85XX_FEC
 	{
 		.regs = (tsec_t *)(TSEC_BASE_ADDR + 0x2000),
-		.miiregs = (tsec_t *)(TSEC_BASE_ADDR),
+		.miiregs = (tsec_mdio_t *)(MDIO_BASE_ADDR),
 		.devname = CONFIG_MPC85XX_FEC_NAME,
 		.phyaddr = FEC_PHY_ADDR,
 		.flags = FEC_FLAGS
@@ -136,6 +136,7 @@ int tsec_initialize(bd_t * bis, struct  
 tsec_info_struct *tsec_info)
 	privlist[num_tsecs++] = priv;
 	priv->regs = tsec_info->regs;
 	priv->phyregs = tsec_info->miiregs;
+	priv->phyregs_sgmii = tsec_info->miiregs_sgmii;
 
 	priv->phyaddr = tsec_info->phyaddr;
	priv->flags = tsec_info->flags;
drivers/net/tsec.c +0 -0
@@ -222,7 +223,7 @@ int tsec_init(struct eth_device *dev, bd_t * bd)
 }
 
 /* Writes the given phy's reg with value, using the specified MDIO  

regs */
-static void tsec_local_mdio_write(volatile tsec_t *phyregs, uint addr,
+static void tsec_local_mdio_write(volatile tsec_mdio_t *phyregs, uint addr,
uint reg, uint value)

{
	int timeout = 1000000;
drivers/net/tsec.c +1 -1
@@ -245,7 +246,7 @@ static void tsec_local_mdio_write(volatile  
 tsec_t *phyregs, uint addr,
 * notvalid bit cleared), and the bus to cease activity (miimind
 * busy bit cleared), and then returns the value
 */
-uint tsec_local_mdio_read(volatile tsec_t *phyregs, uint phyid,  
 uint regnum)
+uint tsec_local_mdio_read(volatile tsec_mdio_t *phyregs, uint  
 phyid, uint regnum)
{
	uint value;
drivers/net/tsec.c +0 -0
@@ -290,11 +291,11 @@ static void tsec_configure_serdes(struct  
 tsec_private *priv)
 {
 	/* Access TBI PHY registers at given TSEC register offset as  

opposed to the
* register offset used for external PHY accesses */

drivers/net/tsec.c +1 -1
-	tsec_local_mdio_write(priv->regs, priv->regs->tbipa, TBI_ANA,
+	tsec_local_mdio_write(priv->phyregs_sgmii, priv->regs->tbipa,  

TBI_ANA,

			TBIANA_SETTINGS);
drivers/net/tsec.c +1 -1
-	tsec_local_mdio_write(priv->regs, priv->regs->tbipa, TBI_TBICON,
+	tsec_local_mdio_write(priv->phyregs_sgmii, priv->regs->tbipa,  

TBI_TBICON,

			TBICON_CLK_SELECT);
drivers/net/tsec.c +1 -1
-	tsec_local_mdio_write(priv->regs, priv->regs->tbipa, TBI_CR,
+	tsec_local_mdio_write(priv->phyregs_sgmii, priv->regs->tbipa,  

TBI_CR,

			TBICR_SETTINGS);
}
drivers/net/tsec.c +2 -3
@@ -306,12 +307,11 @@ static int init_phy(struct eth_device *dev)
 {
 	struct tsec_private *priv = (struct tsec_private *)dev->priv;
 	struct phy_info *curphy;
-	volatile tsec_t *phyregs = priv->phyregs;
+	volatile tsec_mdio_t *phyregs = priv->phyregs;
 	volatile tsec_t *regs = priv->regs;
 
 	/* Assign a Physical address to the TBI */
 	regs->tbipa = CONFIG_SYS_TBIPA_VALUE;
-	phyregs->tbipa = CONFIG_SYS_TBIPA_VALUE;
 	asm("sync");
 
 	/* Reset MII (due to new addresses) */
@@ -739,7 +739,7 @@ uint mii_parse_dm9161_scsr(uint mii_reg, struct  
 tsec_private * priv)
 uint mii_cis8204_fixled(uint mii_reg, struct tsec_private * priv)
 {
 	uint phyid;
-	volatile tsec_t *regbase = priv->phyregs;
+	volatile tsec_mdio_t *regbase = priv->phyregs;
 	int timeout = 1000000;
 
	for (phyid = 0; phyid < 4; phyid++) {
drivers/net/tsec.c +1 -1
@@ -1772,7 +1772,7 @@ void phy_run_commands(struct tsec_private  
 *priv, struct phy_cmd *cmd)
 {
 	int i;
 	uint result;
-	volatile tsec_t *phyregs = priv->phyregs;
+	volatile tsec_mdio_t *phyregs = priv->phyregs;
 
 	phyregs->miimcfg = MIIMCFG_RESET;
include/asm-ppc/ renamed from include/asm-ppc/immap_83xx.h +0 -0

immap_83xx.h
index c60a7d2..57b1a72 100644

include/asm-ppc/immap_83xx.h +9 -0
@@ -868,4 +868,13 @@ typedef struct immap {
 #endif
 #define CONFIG_SYS_MPC83xx_USB_ADDR \
 			(CONFIG_SYS_IMMR + CONFIG_SYS_MPC83xx_USB_OFFSET)
+
+#define CONFIG_SYS_TSEC1_OFFSET		0x24000
+#define TSEC_SIZE			0x01000
+
+#define CONFIG_SYS_MDIO1_OFFSET		0x24520
+#define MDIO_OFFSET			0x01000
+
+#define TSEC_BASE_ADDR		(CONFIG_SYS_IMMR + CONFIG_SYS_TSEC1_OFFSET)
+#define MDIO_BASE_ADDR		(CONFIG_SYS_IMMR + CONFIG_SYS_MDIO1_OFFSET)
 #endif				/* __IMMAP_83xx__ */
include/asm-ppc/ renamed from include/asm-ppc/immap_85xx.h +0 -0

immap_85xx.h
index 4194295..ad3910c 100644

include/asm-ppc/immap_85xx.h +10 -0
@@ -1932,4 +1932,14 @@ typedef struct ccsr_gur {
 #define CONFIG_SYS_MPC85xx_USB_ADDR \
 	(CONFIG_SYS_IMMR + CONFIG_SYS_MPC85xx_USB_OFFSET)
 
+/* TSEC and MDIO OFFSETS */
+#define CONFIG_SYS_TSEC1_OFFSET		0x24000
+#define TSEC_SIZE			0x01000
+
+#define CONFIG_SYS_MDIO1_OFFSET		0x24520
+#define MDIO_OFFSET			0x01000
+
+#define TSEC_BASE_ADDR		(CONFIG_SYS_IMMR + CONFIG_SYS_TSEC1_OFFSET)
+#define MDIO_BASE_ADDR		(CONFIG_SYS_IMMR + CONFIG_SYS_MDIO1_OFFSET)
+
 #endif /*__IMMAP_85xx__*/
include/asm-ppc/ renamed from include/asm-ppc/immap_86xx.h +0 -0

immap_86xx.h
index fdfc654..80e7ecd 100644

include/asm-ppc/immap_86xx.h +9 -0
@@ -1298,4 +1298,13 @@ extern immap_t  *immr;
 #define CONFIG_SYS_MPC86xx_DMA_OFFSET	(0x21000)
 #define CONFIG_SYS_MPC86xx_DMA_ADDR	(CONFIG_SYS_IMMR +  
 CONFIG_SYS_MPC86xx_DMA_OFFSET)
 
+#define CONFIG_SYS_TSEC1_OFFSET		0x24000
+#define TSEC_SIZE			0x01000
+
+#define CONFIG_SYS_MDIO1_OFFSET		0x24520
+#define MDIO_OFFSET			0x01000
+
+#define TSEC_BASE_ADDR		(CONFIG_SYS_IMMR + CONFIG_SYS_TSEC1_OFFSET)
+#define MDIO_BASE_ADDR		(CONFIG_SYS_IMMR + CONFIG_SYS_MDIO1_OFFSET)
+

#endif /*__IMMAP_86xx__*/

include/tsec.h +1 -8
index 0ac3034..2b9c9c3 100644
@@ -7,7 +7,7 @@
 *  terms of the GNU Public License, Version 2, incorporated
 *  herein by reference.
 *
- * Copyright 2004, 2007 Freescale Semiconductor, Inc.
+ * Copyright 2004, 2007, 2009  Freescale Semiconductor, Inc.
 * (C) Copyright 2003, Motorola, Inc.
 * maintained by Xianghua Xiao (x.xiao at motorola.com)
 * author Andy Fleming
@@ -20,22 +20,11 @@
 #include <net.h>
 #include <config.h>
 
-#ifndef CONFIG_SYS_TSEC1_OFFSET
-    #define CONFIG_SYS_TSEC1_OFFSET	(0x24000)
-#endif
-
-#define TSEC_SIZE	0x01000
-
-/* FIXME:  Should these be pushed back to 83xx and 85xx config  

files? */

include/tsec.h +0 -3
-#if defined(CONFIG_MPC85xx) || defined(CONFIG_MPC86xx) \
-	|| defined(CONFIG_MPC83xx)
-    #define TSEC_BASE_ADDR	(CONFIG_SYS_IMMR +  

CONFIG_SYS_TSEC1_OFFSET)

include/tsec.h +0 -2
-#endif
-

#define STD_TSEC_INFO(num) \

{			\
	.regs = (tsec_t *)(TSEC_BASE_ADDR + ((num - 1) * TSEC_SIZE)), \
include/tsec.h +2 -1
-	.miiregs = (tsec_t *)TSEC_BASE_ADDR, \
+	.miiregs = (tsec_mdio_t *)(MDIO_BASE_ADDR), \
+	.miiregs_sgmii = (tsec_mdio_t *)(MDIO_BASE_ADDR + (num -1) 
*MDIO_OFFSET ), \
	.devname = CONFIG_TSEC##num##_NAME, \
	.phyaddr = TSEC##num##_PHY_ADDR, \
	.flags = TSEC##num##_FLAGS \
include/tsec.h +2 -1
@@ -44,7 +33,8 @@
 #define SET_STD_TSEC_INFO(x, num) \
 {			\
 	x.regs = (tsec_t *)(TSEC_BASE_ADDR + ((num - 1) * TSEC_SIZE)); \
-	x.miiregs = (tsec_t *)TSEC_BASE_ADDR; \
+	x.miiregs = (tsec_mdio_t *)(MDIO_BASE_ADDR); \
+	x.miiregs_sgmii = (tsec_mdio_t *)(MDIO_BASE_ADDR + (num -1) 
 *MDIO_OFFSET); \
 	x.devname = CONFIG_TSEC##num##_NAME; \
 	x.phyaddr = TSEC##num##_PHY_ADDR; \
	x.flags = TSEC##num##_FLAGS;\
include/tsec.h +10 -0
@@ -461,6 +451,16 @@ typedef struct tsec_hash_regs
 	uint	res2[24];
 } tsec_hash_t;
 
+typedef struct tsec_mdio
+{
+	uint	miimcfg;	/* MII Management: Configuration */
+	uint	miimcom;	/* MII Management: Command */
+	uint	miimadd;	/* MII Management: Address */
+	uint	miimcon;	/* MII Management: Control */
+	uint	miimstat;	/* MII Management: Status */
+	uint	miimind;	/* MII Management: Indicators */
+} tsec_mdio_t;
+

typedef struct tsec

{
	/* General Control and Status Registers (0x2_n000) */
include/tsec.h +5 -8
@@ -526,12 +526,7 @@ typedef struct tsec
 
 	uint	res51c;
 
-	uint	miimcfg;	/* MII Management: Configuration */
-	uint	miimcom;	/* MII Management: Command */
-	uint	miimadd;	/* MII Management: Address */
-	uint	miimcon;	/* MII Management: Control */
-	uint	miimstat;	/* MII Management: Status */
-	uint	miimind;	/* MII Management: Indicators */
+	uint	resmdio[6];
 
 	uint	res538;
 
@@ -571,7 +566,8 @@ typedef struct tsec
 
 struct tsec_private {
 	volatile tsec_t *regs;
-	volatile tsec_t *phyregs;
+	volatile tsec_mdio_t *phyregs;
+	volatile tsec_mdio_t *phyregs_sgmii;
 	struct phy_info *phyinfo;
 	uint phyaddr;
 	u32 flags;
@@ -630,7 +626,8 @@ struct phy_info {
 
 struct tsec_info_struct {
 	tsec_t *regs;
-	tsec_t *miiregs;
+	tsec_mdio_t *miiregs;
+	tsec_mdio_t *miiregs_sgmii;
 	char *devname;
 	unsigned int phyaddr;
 	u32 flags;
Signature · 6 lines
1.5.2.2

_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
#2 lore raw

PATCH v2 1/2 NET: Move MDIO regs out of TSEC Space

In reply to Sandeep Gopalpet

Dear Ben & KIm,

Quoted 11 lines · In message <[email protected]>…

Moved the mdio regs out of the tsec structure,and provided different offsets for tsec base and mdio base so that provision for etsec2.0 can be provided.

This patch helps in providing the support for etsec2.0 In etsec2.0, the MDIO register space and the etsec reg space are different.

Also, moved the TSEC_BASE_ADDR and MDIO_BASE_ADDR definitons into platform specific files.

Quoted 8 lines
---
 drivers/net/tsec.c           |   20 +++++++++---------
 include/asm-ppc/immap_83xx.h |    9 ++++++++
 include/asm-ppc/immap_85xx.h |   10 +++++++++
 include/asm-ppc/immap_86xx.h |    9 ++++++++
 include/tsec.h               |   43 +++++++++++++++++++----------------------
 5 files changed, 58 insertions(+), 33 deletions(-)

What's the status of this patch?

And ditto for [PATCH v2 2/2] NET: Base support for etsec2.0 ?

Best regards,

Wolfgang Denk

Signature · 5 lines
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
Only two things are infinite,  the universe and human stupidity,  and
I'm not sure about the former.                     -- Albert Einstein
#3 lore raw

PATCH v2 1/2 NET: Move MDIO regs out of TSEC Space

Quoted 25 lines · Wolfgang Denk

Dear Ben & KIm,

In message <12564079493940-git-send-email-

Quoted 12 lines · sandeep.kumar at freescale.com> Sandeep Gopalpet wrote:

Moved the mdio regs out of the tsec structure,and provided different offsets for tsec base and mdio base so that provision for etsec2.0 can be provided.

This patch helps in providing the support for etsec2.0 In etsec2.0, the MDIO register space and the etsec reg space are different.

Also, moved the TSEC_BASE_ADDR and MDIO_BASE_ADDR definitons into platform specific files.

Quoted 8 lines

---

drivers/net/tsec.c           |   20 +++++++++---------
include/asm-ppc/immap_83xx.h |    9 ++++++++
include/asm-ppc/immap_85xx.h |   10 +++++++++
include/asm-ppc/immap_86xx.h |    9 ++++++++
include/tsec.h               |   43 ++++++++++++++++++ 
+----------------------
5 files changed, 58 insertions(+), 33 deletions(-)
Quoted 7 lines

What's the status of this patch?

And ditto for [PATCH v2 2/2] NET: Base support for etsec2.0 ?

Best regards,

Wolfgang Denk

These are for the next release. I have them queued up in a next branch.

- k