display and keypad support for nhk8815

This patch set implements display and keypad support. To turn the display on I need the STMPE2401 port expander, set up as a separate driver in this patch set.

It's the same set I sent for RFC on Oct 9 2009, with the requested fixes. I also added commit messages to each of them, and an initial nhk-specific patch that was not submitted for RFC.

Detailed list of changes from V1 (as well as fixed message-id):

1/9 (nhk8815: fix i2c and other gpios at board_init time, not later):
new patch, needed to apply the other ones.
Please note that there is a block with local variables;
I know it is generally not advisable but they are really of strictly local use, I think they deserve their limited scope.

2/9 (video: add amba-clcd prime-cell):
include/amba_clcd.h: fixed white space (spaces before tab) better comments on the data structures

3/9 (include/nomadik.h: add physical address for cldc):
unchanged

4/9 (drivers/misc: add stmpe2401 port extender and keypad controller):
drivers/misc/stmpe2401.c: newlined all statements of if/else include/stmpe2401.h: white space fixes
====> Note: I did not turn it into a C structure, as those registers
are I2C registers, so they are plain numbers, not offsets in an I/O memory region where I use readl/writel

5/9 (nhk8815.h: define we need stmpe):
unchanged

6/9 (lcd: make 16bpp work):
declared the new "d" pointer in new ifdef block. I dislike it, but
my previous approach to avoid the ifdef was nacked. common/lcd.c is a mess, unfortunately.
I made "./MAKEALL arm" and "./MAKEALL ppc" with no adverse effects.

7/9 (nhk8815: added keypad):
layout (space, if blocks)
removed extra __LINE__ temporary printouts
added an header for local prototypes

8/9 (nhk8815: start lower in RAM, so the 800x480 frame buffer fits):
changed the comment in config.mk.

9/9 (nhk8815: added lcd support):
white space changes (tabified the structures) removed the __LINE__ temporary printouts
used the header introduced in 7/9 for local prototypes

Alessandro Rubini (9):
nhk8815: change the order of initialization
video: add amba-clcd prime-cell
include/nomadik.h: add physical address for cldc drivers/misc: add stmpe2401 port extender and keypad controller nhk8815.h: define we need stmpe
lcd: make 16bpp work
nhk8815: added keypad
nhk8815: start lower in RAM, so the 800x480 frame buffer fits
nhk8815: added lcd support

 board/st/nhk8815/Makefile          |    6 +-
 board/st/nhk8815/config.mk         |    8 +-
 board/st/nhk8815/keypad.c          |   99 +++++++++++++++++++
 board/st/nhk8815/lcd.c             |   87 ++++++++++++++++
 board/st/nhk8815/nhk8815-devices.h |    8 ++
 board/st/nhk8815/nhk8815.c         |   38 +++++--
 common/lcd.c                       |   27 ++++-
 drivers/misc/Makefile              |    1 +
 drivers/misc/stmpe2401.c           |  191 ++++++++++++++++++++++++++++++++++++
 drivers/video/Makefile             |    1 +
 drivers/video/amba.c               |   86 ++++++++++++++++
 include/amba_clcd.h                |   85 ++++++++++++++++
 include/configs/nhk8815.h          |   20 ++++-
 include/nomadik.h                  |    1 +
 include/stmpe2401.h                |   66 ++++++++++++
 15 files changed, 701 insertions(+), 23 deletions(-)
 create mode 100644 board/st/nhk8815/keypad.c
 create mode 100644 board/st/nhk8815/lcd.c
 create mode 100644 board/st/nhk8815/nhk8815-devices.h
 create mode 100644 drivers/misc/stmpe2401.c
 create mode 100644 drivers/video/amba.c
 create mode 100644 include/amba_clcd.h
 create mode 100644 include/stmpe2401.h

From: Alessandro Rubini <[email protected]>

Some inizialization was in board_late_init(), but to satisfy drivers added in the next patches must be performed in normal board_init. This patch leaves board_late_init() empty, but later patches fill it.

---
 board/st/nhk8815/nhk8815.c |   31 +++++++++++++++++++++----------
 1 files changed, 21 insertions(+), 10 deletions(-)

index faef810..eadce40 100644
@@ -60,22 +60,26 @@ int board_init(void)
 	writel(0x02100551, NOMADIK_FSMC_BASE + 0x04); /* FSMC_BTR0 */
 
 	icache_enable();
-	return 0;
-}
 
-int board_late_init(void)
-{
+	/*
+	 * Configure I2C pins, as we will use I2C in a later commit
+	 */
+
 	/* Set the two I2C gpio lines to be gpio high */
 	nmk_gpio_set(__SCL, 1);	nmk_gpio_set(__SDA, 1);
 	nmk_gpio_dir(__SCL, 1);	nmk_gpio_dir(__SDA, 1);
 	nmk_gpio_af(__SCL, GPIO_GPIO); nmk_gpio_af(__SDA, GPIO_GPIO);
 
-	/* Reset the I2C port expander, on GPIO77 */
-	nmk_gpio_af(77, GPIO_GPIO);
-	nmk_gpio_dir(77, 1);
-	nmk_gpio_set(77, 0);
-	udelay(10);
-	nmk_gpio_set(77, 1);
+	/* Put the two I2C port expanders out of reset, on GPIO77 and 79 */
+	{
+		int n[2]={77, 79};
+		int i;
+		for (i = 0; i < ARRAY_SIZE(n); i++) {
+			nmk_gpio_af(n[i], GPIO_GPIO);
+			nmk_gpio_dir(n[i], 1);
+			nmk_gpio_set(n[i], 1);
+		}
+	}
 
 	return 0;
 }

@@ -101,3 +105,10 @@ int board_eth_init(bd_t *bis)
 	return rc;
 }
 #endif
+
+/* Initialization callback, from lib_arm/board.c */
+int board_late_init(void)
+{
+	return 0;
+}
+

1.6.0.2

From: Alessandro Rubini <[email protected]>

This adds support for the CLCD logic cell. It accepts precompiled register values for specific configuration through a board-supplied data structure. It is used by the Nomadik nhk8815, added by a later patch in this series.

---
 drivers/video/Makefile |    1 +
 drivers/video/amba.c   |   86 ++++++++++++++++++++++++++++++++++++++++++++++++
 include/amba_clcd.h    |   85 +++++++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 172 insertions(+), 0 deletions(-)
 create mode 100644 drivers/video/amba.c
 create mode 100644 include/amba_clcd.h

index bb6b5a0..a5e339a 100644
@@ -29,6 +29,7 @@ COBJS-$(CONFIG_ATI_RADEON_FB) += ati_radeon_fb.o
 COBJS-$(CONFIG_ATMEL_LCD) += atmel_lcdfb.o
 COBJS-$(CONFIG_CFB_CONSOLE) += cfb_console.o
 COBJS-$(CONFIG_S6E63D6) += s6e63d6.o
+COBJS-$(CONFIG_VIDEO_AMBA) += amba.o
 COBJS-$(CONFIG_VIDEO_CT69000) += ct69000.o
 COBJS-$(CONFIG_VIDEO_MB862xx) += mb862xx.o
 COBJS-$(CONFIG_VIDEO_MX3) += mx3fb.o

1.6.0.2

Hello Alessandro,

Alessandro Rubini <[email protected]> wrote:

<snip>

...

Hello

I disagree for two reasons: the register exists in the logic block, and the code is copied from a linux header (as noted in the file itself).

Since the clcd block is not something designed for the nomadik but the standard primecell, I don't think trimming its definition is useful; other boards can benefit from the header being complete.

I planned to used it, and this is the complete information that's needed, and I plan to implement it sooner or later. Nonetheless, I understand your request to remove it and I have no problems here.

Ok, no problem.

/alessandro

Alessandro Rubini <[email protected]> wrote:

...

I understand your arguments. If Wolfgang will not reject my pull request, I'm fine with it. Could you please use something like:

struct clcd_regs {
	u32 tim0;
	u32 tim1;
	u32 tim2;
	u32 tim3;
	u32 ubas;
	u32 lbas;
#if !defined(CONFIG_ARCH_VERSATILE) && !defined(CONFIG_ARCH_REALVIEW)
	u32 ienb;
	u32 cntl;

#else
/*
* Someone rearranged these two registers on the Versatile
* platform...
*/

	u32 cntl;
	u32 ienb;
#endif
	u32 stat;
	u32 intr;
	u32 ucur;
	u32 lcur;
	u32 res[0x74];
	u32 pal;
};

in the amba_clcd header?

And then in the code something like:

	struct clcd_regs *regs;
	...

	...
	regs = (struct clcd_regs *)NOMADIK_CLCDC_BASE;
	...
	writel(regval->tim0, &regs->tim0);
	...

Thanks,
Anatolij

Ok, I'll rearrange as a data structure as you both suggest.
[I noted you already did the work for me in your message, thanks for that]

/alessandro

Dear Alessandro,

Actually such a register descriptiion must not be implemented by offset definitions at all. Please define a C struct, and access it using appropriate accessor functions only.

Best regards,

Wolfgang Denk

DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
It is necessary to have purpose.
	-- Alice #1, "I, Mudd", stardate 4513.3

From: Alessandro Rubini <[email protected]>

---
 include/nomadik.h |    1 +
 1 files changed, 1 insertions(+), 0 deletions(-)

index d9405fd..ea65b2d 100644
@@ -4,6 +4,7 @@
 #define __NOMADIK_H__
 
 /* Base addresses of our peripherals */
+#define NOMADIK_CLCDC_BASE	0x10120000	/* CLCD Controller */
 #define NOMADIK_SRC_BASE	0x101E0000	/* System and Reset Cnt */
 #define NOMADIK_PMU_BASE	0x101E9000	/* Power Management Unit */
 #define NOMADIK_MPMC_BASE	0x10110000	/* SDRAM Controller */

1.6.0.2

From: Alessandro Rubini <[email protected]>

This driver is an i2c device acting as a port extender. Since the keypad can be configured to act on specific row and column lines, the specific setup is passed by the board file. This is used by the Nomadik nhk8815, through a later patch in this series.

---
 drivers/misc/Makefile    |    1 +
 drivers/misc/stmpe2401.c |  191 ++++++++++++++++++++++++++++++++++++++++++++++
 include/stmpe2401.h      |   66 ++++++++++++++++
 3 files changed, 258 insertions(+), 0 deletions(-)
 create mode 100644 drivers/misc/stmpe2401.c
 create mode 100644 include/stmpe2401.h

index f6df60f..76c009a 100644
@@ -30,6 +30,7 @@ COBJS-$(CONFIG_DS4510)  += ds4510.o
 COBJS-$(CONFIG_FSL_LAW) += fsl_law.o
 COBJS-$(CONFIG_NS87308) += ns87308.o
 COBJS-$(CONFIG_STATUS_LED) += status_led.o
+COBJS-$(CONFIG_STMPE2401) += stmpe2401.o
 COBJS-$(CONFIG_TWL4030_LED) += twl4030_led.o
 
 COBJS	:= $(COBJS-y)

1.6.0.2

From: Alessandro Rubini <[email protected]>

---
 include/configs/nhk8815.h |    7 ++++++-
 1 files changed, 6 insertions(+), 1 deletions(-)

index a00c2fb..e1be45b 100644
@@ -110,7 +110,7 @@
 #define CONFIG_PL01x_PORTS	{ (void *)CFG_SERIAL0, (void *)CFG_SERIAL1 }
 #define CONFIG_PL011_CLOCK	48000000
 
-/* i2c, for the port extenders (uses gpio.c in board directory) */
+/* i2c, for the stmpe2401 port extenders (uses gpio.c in board directory) */
 #ifndef __ASSEMBLY__
 #include <asm/arch/gpio.h>
 #define CONFIG_CMD_I2C

@@ -126,6 +126,11 @@
 #define I2C_DELAY     (udelay(2))
 #endif /* __ASSEMBLY__ */
 
+/* Activate port extenders and define their i2c address */
+#define CONFIG_STMPE2401
+#define STMPE0  0x43
+#define STMPE1  0x44
+
 /* Ethernet */
 #define PCI_MEMORY_VADDR	0xe8000000
 #define PCI_IO_VADDR		0xee000000

1.6.0.2

From: Alessandro Rubini <[email protected]>

Support for 16bpp was supposed to be in the code but was not working. This makes it work and has been tested in the nhk8815 board.

---
 common/lcd.c |   27 +++++++++++++++++++++------
 1 files changed, 21 insertions(+), 6 deletions(-)

index 4e31618..3d9bfdf 100644
@@ -63,7 +63,7 @@
 /************************************************************************/
 #ifdef CONFIG_LCD_LOGO
 # include <bmp_logo.h>		/* Get logo data, width and height	*/
-# if (CONSOLE_COLOR_WHITE >= BMP_LOGO_OFFSET)
+# if (CONSOLE_COLOR_WHITE >= BMP_LOGO_OFFSET) && (LCD_BPP != LCD_COLOR16)
 #  error Default Color Map overlaps with Logo Color Map
 # endif
 #endif

@@ -218,8 +218,12 @@ static void lcd_drawchars (ushort x, ushort y, uchar *str, int count)
 
 	for (row=0;  row < VIDEO_FONT_HEIGHT;  ++row, dest += lcd_line_length)  {
 		uchar *s = str;
-		uchar *d = dest;
 		int i;
+#if LCD_BPP == LCD_COLOR16
+		ushort *d = (ushort *)dest;
+#else
+		uchar *d = dest;
+#endif
 
 #if LCD_BPP == LCD_MONOCHROME
 		uchar rest = *d & -(1 << (8-off));

@@ -244,9 +248,8 @@ static void lcd_drawchars (ushort x, ushort y, uchar *str, int count)
 				bits <<= 1;
 			}
 #elif LCD_BPP == LCD_COLOR16
-			for (c=0; c<16; ++c) {
-				*d++ = (bits & 0x80) ?
-						lcd_color_fg : lcd_color_bg;
+			for (c=0; c<8; ++c) {
+				*d++ = (bits & 0x80) ? 0xffff : 0;
 				bits <<= 1;
 			}
 #endif

@@ -529,6 +532,13 @@ void bitmap_plot (int x, int y)
 		cmap = (ushort *)&(cp->lcd_cmap[BMP_LOGO_OFFSET*sizeof(ushort)]);
 #elif defined(CONFIG_ATMEL_LCD)
 		cmap = (uint *) (panel_info.mmio + ATMEL_LCDC_LUT(0));
+#else
+		/*
+		 * default case: generic system with no cmap (most likely 16bpp)
+		 * We set cmap to the source palette, so no change is done.
+		 * This avoids even more ifdef in the next stanza
+		 */
+		cmap = bmp_logo_palette;
 #endif
 
 		WATCHDOG_RESET();

@@ -567,10 +577,15 @@ void bitmap_plot (int x, int y)
 		}
 	}
 	else { /* true color mode */
+		u16 col16;
 		fb16 = (ushort *)(lcd_base + y * lcd_line_length + x);
 		for (i=0; i<BMP_LOGO_HEIGHT; ++i) {
 			for (j=0; j<BMP_LOGO_WIDTH; j++) {
-				fb16[j] = bmp_logo_palette[(bmap[j])];
+				col16 = bmp_logo_palette[(bmap[j]-16)];
+				fb16[j] =
+					((col16 & 0x000F) << 1) |
+					((col16 & 0x00F0) << 3) |
+					((col16 & 0x0F00) << 4);
 				}
 			bmap += BMP_LOGO_WIDTH;
 			fb16 += panel_info.vl_col;

1.6.0.2

Alessandro Rubini <[email protected]> wrote:

<snip>

From: Alessandro Rubini <[email protected]>

This patch adds keypad support for the nhk8815 board, based on the stmpe2401 driver. The keypad hosts 16 keys, so each of them sends a string instead of a single key. The provided keymap is only an example and must be customized according to the use case.

---
 board/st/nhk8815/Makefile          |    5 ++-
 board/st/nhk8815/keypad.c          |   99 ++++++++++++++++++++++++++++++++++++
 board/st/nhk8815/nhk8815-devices.h |    7 +++
 board/st/nhk8815/nhk8815.c         |    4 ++
 include/configs/nhk8815.h          |    3 +
 5 files changed, 117 insertions(+), 1 deletions(-)
 create mode 100644 board/st/nhk8815/keypad.c
 create mode 100644 board/st/nhk8815/nhk8815-devices.h

index b37fe53..1bb1d2c 100644
@@ -29,7 +29,10 @@ include $(TOPDIR)/config.mk
 
 LIB	= $(obj)lib$(BOARD).a
 
-COBJS	:= nhk8815.o
+COBJS-y	:= nhk8815.o
+COBJS-$(CONFIG_NHK8815_KEYPAD) += keypad.o
+
+COBJS	:= $(COBJS-y)
 SOBJS	:= platform.o
 
 SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)

new file mode 100644
index 0000000..78252ed
@@ -0,0 +1,7 @@
+#ifndef __NHK8815_DEVICES__
+#define __NHK8815_DEVICES__
+
+/* Prototypes for functions exported by device files in this directory */
+extern int nhk8815_keypad_init(void);          /* ./keypad.c */
+
+#endif /* __NHK8815_DEVICES__ */

index eadce40..fbabd15 100644
@@ -29,6 +29,7 @@
 #include <netdev.h>
 #include <asm/io.h>
 #include <asm/arch/gpio.h>
+#include "nhk8815-devices.h"
 
 DECLARE_GLOBAL_DATA_PTR;
 

@@ -109,6 +110,9 @@ int board_eth_init(bd_t *bis)
 /* Initialization callback, from lib_arm/board.c */
 int board_late_init(void)
 {
+#ifdef CONFIG_NHK8815_KEYPAD
+	nhk8815_keypad_init();
+#endif
 	return 0;
 }
 

index e1be45b..f9dbd7a 100644
@@ -131,6 +131,9 @@
 #define STMPE0  0x43
 #define STMPE1  0x44
 
+/* Keypad using stmpe2401 */
+#define CONFIG_NHK8815_KEYPAD
+
 /* Ethernet */
 #define PCI_MEMORY_VADDR	0xe8000000
 #define PCI_IO_VADDR		0xee000000

1.6.0.2

From: Alessandro Rubini <[email protected]>

This simply moves u-boot to a lower address, as the frame buffer is allocated after u-boot itself in memory.

---
 board/st/nhk8815/config.mk |    8 +++-----
 1 files changed, 3 insertions(+), 5 deletions(-)

index 590393b..6e5e358 100644
@@ -18,9 +18,7 @@
 # along with this program; if not, write to the Free Software
 # Foundation, Inc., 59 Temple Place, Suite 330, Boston,
 # MA 02111-1307 USA
-#
-#
-# image should be loaded at 0x01000000
-#
 
-TEXT_BASE = 0x03F80000
+# Start 4MB before the end, as the frame buffer is allocate after
+# u-boot. 800x480 @ 32bpp takes 1.5MB alone, so let's play safe.
+TEXT_BASE = 0x03c00000

1.6.0.2

From: Alessandro Rubini <[email protected]>

This adds lcd support for the board. It includes defines for 32-bit parameter as well, although support for LCD_COLOR32 is not yet in u-boot. This uses the stmpe2401 to turn on display backlight.

---
 board/st/nhk8815/Makefile          |    1 +
 board/st/nhk8815/lcd.c             |   87 ++++++++++++++++++++++++++++++++++++
 board/st/nhk8815/nhk8815-devices.h |    1 +
 board/st/nhk8815/nhk8815.c         |    3 +
 include/configs/nhk8815.h          |   10 ++++
 5 files changed, 102 insertions(+), 0 deletions(-)
 create mode 100644 board/st/nhk8815/lcd.c

index 1bb1d2c..7155f12 100644
@@ -31,6 +31,7 @@ LIB	= $(obj)lib$(BOARD).a
 
 COBJS-y	:= nhk8815.o
 COBJS-$(CONFIG_NHK8815_KEYPAD) += keypad.o
+COBJS-$(CONFIG_LCD) += lcd.o
 
 COBJS	:= $(COBJS-y)
 SOBJS	:= platform.o

index 78252ed..aec5825 100644
@@ -3,5 +3,6 @@
 
 /* Prototypes for functions exported by device files in this directory */
 extern int nhk8815_keypad_init(void);          /* ./keypad.c */
+extern int nhk8815_backlight_on(void);		/* in ./lcd.c */
 
 #endif /* __NHK8815_DEVICES__ */

index fbabd15..fedb3c0 100644
@@ -113,6 +113,9 @@ int board_late_init(void)
 #ifdef CONFIG_NHK8815_KEYPAD
 	nhk8815_keypad_init();
 #endif
+#ifdef CONFIG_LCD
+	nhk8815_backlight_on();
+#endif
 	return 0;
 }
 

index f9dbd7a..ad098d9 100644
@@ -134,6 +134,16 @@
 /* Keypad using stmpe2401 */
 #define CONFIG_NHK8815_KEYPAD
 
+/* Display support */
+#define CONFIG_LCD
+#define CONFIG_LCD_LOGO
+#define CONFIG_LCD_INFO_BELOW_LOGO
+#define CONFIG_SYS_WHITE_ON_BLACK
+#define LCD_BPP				LCD_COLOR16
+#define CONFIG_VIDEO_AMBA
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV	1
+#define CONFIG_CONSOLE_MUX
+
 /* Ethernet */
 #define PCI_MEMORY_VADDR	0xe8000000
 #define PCI_IO_VADDR		0xee000000

1.6.0.2

I'm sorry I forgot a few extra prints in there:

Dear Alessandro Rubini,

If you want this included into mainline, you have to post here. I will not accept any patches that have not been posted on this list (and thus found their way into the list archive).

Best regards,

Wolfgang Denk

DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
There's no sense in being precise  when  you  don't  even  know  what
you're talking about.                             -- John von Neumann