Skip to contentSkip to conversation

e1000e: minor correction to name of bit in CTRL_EXT register

PATCH Applied Jeff Kirsher 2 participants 6 messages Dec 8, 2009 – Dec 9, 2009

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/3 e1000e: minor correction to name of bit in CTRL_EXT register

From: Bruce Allan <[email protected]>

Bit 7 in the CTRL_REG register is actually the Software Definable Pin 3, not the Software Definable Pin 7.

---

 drivers/net/e1000e/defines.h |    2 +-
 drivers/net/e1000e/netdev.c  |    2 +-
 2 files changed, 2 insertions(+), 2 deletions(-)
drivers/net/e1000e/defines.h +1 -1
index 86d2809..e02e382 100644
@@ -74,7 +74,7 @@
 #define E1000_WUS_BC           E1000_WUFC_BC
 
 /* Extended Device Control */
-#define E1000_CTRL_EXT_SDP7_DATA 0x00000080 /* Value of SW Definable Pin 7 */
+#define E1000_CTRL_EXT_SDP3_DATA 0x00000080 /* Value of SW Definable Pin 3 */
 #define E1000_CTRL_EXT_EE_RST    0x00002000 /* Reinitialize from EEPROM */
 #define E1000_CTRL_EXT_SPD_BYPS  0x00008000 /* Speed Select Bypass */
 #define E1000_CTRL_EXT_RO_DIS    0x00020000 /* Relaxed Ordering disable */
drivers/net/e1000e/netdev.c +1 -1
index c3105c5..762b697 100644
@@ -4541,7 +4541,7 @@ static int __e1000_shutdown(struct pci_dev *pdev, bool *enable_wake)
 		    e1000_media_type_internal_serdes) {
 			/* keep the laser running in D3 */
 			ctrl_ext = er32(CTRL_EXT);
-			ctrl_ext |= E1000_CTRL_EXT_SDP7_DATA;
+			ctrl_ext |= E1000_CTRL_EXT_SDP3_DATA;
 			ew32(CTRL_EXT, ctrl_ext);
 		}
 
#1 lore raw

PATCH 2/3 e1000e: replace incorrect use of GG82563_REG macro

From: Bruce Allan <[email protected]>

The GG82563_REG() macro should not be used to determine the offset provided to the e1000e_[read|write]_kmrn_reg() functions since the first argument to the macro is already implied and gets masked off anyway in the functions. The resultant register reads/writes with this patch are functionally the same as before.

---

 drivers/net/e1000e/hw.h      |    2 ++
 drivers/net/e1000e/ich8lan.c |    8 +++++---
 2 files changed, 7 insertions(+), 3 deletions(-)
drivers/net/e1000e/hw.h +2 -0
index a7d08da..5ed1788 100644
@@ -302,6 +302,8 @@ enum e1e_registers {
 #define E1000_KMRNCTRLSTA_OFFSET_SHIFT	16
 #define E1000_KMRNCTRLSTA_REN		0x00200000
 #define E1000_KMRNCTRLSTA_DIAG_OFFSET	0x3    /* Kumeran Diagnostic */
+#define E1000_KMRNCTRLSTA_TIMEOUTS	0x4    /* Kumeran Timeouts */
+#define E1000_KMRNCTRLSTA_INBAND_PARAM	0x9    /* Kumeran InBand Parameters */
 #define E1000_KMRNCTRLSTA_DIAG_NELPBK	0x1000 /* Nearend Loopback mode */
 #define E1000_KMRNCTRLSTA_K1_CONFIG	0x7
 #define E1000_KMRNCTRLSTA_K1_ENABLE	0x140E
drivers/net/e1000e/ich8lan.c +5 -3
index 7b33be9..9b09246 100644
@@ -2755,14 +2755,16 @@ static s32 e1000_setup_copper_link_ich8lan(struct e1000_hw *hw)
 	 * and increase the max iterations when polling the phy;
 	 * this fixes erroneous timeouts at 10Mbps.
 	 */
-	ret_val = e1000e_write_kmrn_reg(hw, GG82563_REG(0x34, 4), 0xFFFF);
+	ret_val = e1000e_write_kmrn_reg(hw, E1000_KMRNCTRLSTA_TIMEOUTS, 0xFFFF);
 	if (ret_val)
 		return ret_val;
-	ret_val = e1000e_read_kmrn_reg(hw, GG82563_REG(0x34, 9), &reg_data);
+	ret_val = e1000e_read_kmrn_reg(hw, E1000_KMRNCTRLSTA_INBAND_PARAM,
+	                               &reg_data);
 	if (ret_val)
 		return ret_val;
 	reg_data |= 0x3F;
-	ret_val = e1000e_write_kmrn_reg(hw, GG82563_REG(0x34, 9), reg_data);
+	ret_val = e1000e_write_kmrn_reg(hw, E1000_KMRNCTRLSTA_INBAND_PARAM,
+	                                reg_data);
 	if (ret_val)
 		return ret_val;
 
maintainer Applied
#2 lore raw

Re: [PATCH 2/3] e1000e: replace incorrect use of GG82563_REG macro

From: Jeff Kirsher <[email protected]>
Date: Tue, 08 Dec 2009 09:28:01 -0800

Quoted 10 lines

From: Bruce Allan <[email protected]>

The GG82563_REG() macro should not be used to determine the offset provided to the e1000e_[read|write]_kmrn_reg() functions since the first argument to the macro is already implied and gets masked off anyway in the functions. The resultant register reads/writes with this patch are functionally the same as before.

Applied.

#3 lore raw

PATCH 3/3 e1000e: only perform ESB2 MDIC workaround on certain configurations

In reply to Jeff Kirsher

From: Bruce Allan <[email protected]>

A workaround added for all ESB2 devices (adds a delay for all MDIC accesses which resolves an issue with the MDIC ready bit being set prematurely) is applicable only to devices in which the MAC-PHY interconnect is not operating in a certain mode with in-band MDIO. Check the control register for the operating mode and enable the workaround accordingly.

---

 drivers/net/e1000e/es2lan.c |   97 ++++++++++++++++++++++++++++---------------
 drivers/net/e1000e/hw.h     |    5 ++
 2 files changed, 69 insertions(+), 33 deletions(-)
drivers/net/e1000e/es2lan.c +64 -33
index d2a1047..3028f23 100644
@@ -46,6 +46,9 @@
 #define E1000_KMRNCTRLSTA_HD_CTRL_1000_DEFAULT	 0x0000
 #define E1000_KMRNCTRLSTA_OPMODE_E_IDLE		 0x2000
 
+#define E1000_KMRNCTRLSTA_OPMODE_MASK		 0x000C
+#define E1000_KMRNCTRLSTA_OPMODE_INBAND_MDIO	 0x0004
+
 #define E1000_TCTL_EXT_GCEX_MASK 0x000FFC00 /* Gigabit Carry Extend Padding */
 #define DEFAULT_TCTL_EXT_GCEX_80003ES2LAN	 0x00010000
 
@@ -462,28 +465,36 @@ static s32 e1000_read_phy_reg_gg82563_80003es2lan(struct e1000_hw *hw,
 		return ret_val;
 	}
 
-	/*
-	 * The "ready" bit in the MDIC register may be incorrectly set
-	 * before the device has completed the "Page Select" MDI
-	 * transaction.  So we wait 200us after each MDI command...
-	 */
-	udelay(200);
+	if (hw->dev_spec.e80003es2lan.mdic_wa_enable == true) {
+		/*
+		 * The "ready" bit in the MDIC register may be incorrectly set
+		 * before the device has completed the "Page Select" MDI
+		 * transaction.  So we wait 200us after each MDI command...
+		 */
+		udelay(200);
 
-	/* ...and verify the command was successful. */
-	ret_val = e1000e_read_phy_reg_mdic(hw, page_select, &temp);
+		/* ...and verify the command was successful. */
+		ret_val = e1000e_read_phy_reg_mdic(hw, page_select, &temp);
 
-	if (((u16)offset >> GG82563_PAGE_SHIFT) != temp) {
-		ret_val = -E1000_ERR_PHY;
-		e1000_release_phy_80003es2lan(hw);
-		return ret_val;
-	}
+		if (((u16)offset >> GG82563_PAGE_SHIFT) != temp) {
+			ret_val = -E1000_ERR_PHY;
+			e1000_release_phy_80003es2lan(hw);
+			return ret_val;
+		}
 
-	udelay(200);
+		udelay(200);
 
-	ret_val = e1000e_read_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & offset,
-					   data);
+		ret_val = e1000e_read_phy_reg_mdic(hw,
+		                                  MAX_PHY_REG_ADDRESS & offset,
+		                                  data);
+
+		udelay(200);
+	} else {
+		ret_val = e1000e_read_phy_reg_mdic(hw,
+		                                  MAX_PHY_REG_ADDRESS & offset,
+		                                  data);
+	}
 
-	udelay(200);
 	e1000_release_phy_80003es2lan(hw);
 
 	return ret_val;
@@ -526,28 +537,35 @@ static s32 e1000_write_phy_reg_gg82563_80003es2lan(struct e1000_hw *hw,
 		return ret_val;
 	}
 
+	if (hw->dev_spec.e80003es2lan.mdic_wa_enable == true) {
+		/*
+		 * The "ready" bit in the MDIC register may be incorrectly set
+		 * before the device has completed the "Page Select" MDI
+		 * transaction.  So we wait 200us after each MDI command...
+		 */
+		udelay(200);
 
-	/*
-	 * The "ready" bit in the MDIC register may be incorrectly set
-	 * before the device has completed the "Page Select" MDI
-	 * transaction.  So we wait 200us after each MDI command...
-	 */
-	udelay(200);
+		/* ...and verify the command was successful. */
+		ret_val = e1000e_read_phy_reg_mdic(hw, page_select, &temp);
 
-	/* ...and verify the command was successful. */
-	ret_val = e1000e_read_phy_reg_mdic(hw, page_select, &temp);
+		if (((u16)offset >> GG82563_PAGE_SHIFT) != temp) {
+			e1000_release_phy_80003es2lan(hw);
+			return -E1000_ERR_PHY;
+		}
 
-	if (((u16)offset >> GG82563_PAGE_SHIFT) != temp) {
-		e1000_release_phy_80003es2lan(hw);
-		return -E1000_ERR_PHY;
-	}
+		udelay(200);
 
-	udelay(200);
+		ret_val = e1000e_write_phy_reg_mdic(hw,
+		                                  MAX_PHY_REG_ADDRESS & offset,
+		                                  data);
 
-	ret_val = e1000e_write_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & offset,
-					    data);
+		udelay(200);
+	} else {
+		ret_val = e1000e_write_phy_reg_mdic(hw,
+		                                  MAX_PHY_REG_ADDRESS & offset,
+		                                  data);
+	}
 
-	udelay(200);
 	e1000_release_phy_80003es2lan(hw);
 
 	return ret_val;
@@ -866,6 +884,19 @@ static s32 e1000_init_hw_80003es2lan(struct e1000_hw *hw)
 	reg_data &= ~0x00100000;
 	E1000_WRITE_REG_ARRAY(hw, E1000_FFLT, 0x0001, reg_data);
 
+	/* default to true to enable the MDIC W/A */
+	hw->dev_spec.e80003es2lan.mdic_wa_enable = true;
+
+	ret_val = e1000_read_kmrn_reg_80003es2lan(hw,
+	                              E1000_KMRNCTRLSTA_OFFSET >>
+	                              E1000_KMRNCTRLSTA_OFFSET_SHIFT,
+	                              &i);
+	if (!ret_val) {
+		if ((i & E1000_KMRNCTRLSTA_OPMODE_MASK) ==
+		     E1000_KMRNCTRLSTA_OPMODE_INBAND_MDIO)
+			hw->dev_spec.e80003es2lan.mdic_wa_enable = false;
+	}
+
 	/*
 	 * Clear all of the statistics registers (clear on read).  It is
 	 * important that we do this after we have tried to establish link
drivers/net/e1000e/hw.h +5 -0
index 5ed1788..2784cf4 100644
@@ -900,6 +900,10 @@ struct e1000_dev_spec_82571 {
 	u32 smb_counter;
 };
 
+struct e1000_dev_spec_80003es2lan {
+	bool  mdic_wa_enable;
+};
+
 struct e1000_shadow_ram {
 	u16  value;
 	bool modified;
@@ -928,6 +932,7 @@ struct e1000_hw {
 
 	union {
 		struct e1000_dev_spec_82571	e82571;
+		struct e1000_dev_spec_80003es2lan e80003es2lan;
 		struct e1000_dev_spec_ich8lan	ich8lan;
 	} dev_spec;
 };
maintainer Applied
#4 lore raw

Re: [PATCH 3/3] e1000e: only perform ESB2 MDIC workaround on certain configurations

From: Jeff Kirsher <[email protected]>
Date: Tue, 08 Dec 2009 09:28:20 -0800

Quoted 10 lines

From: Bruce Allan <[email protected]>

A workaround added for all ESB2 devices (adds a delay for all MDIC accesses which resolves an issue with the MDIC ready bit being set prematurely) is applicable only to devices in which the MAC-PHY interconnect is not operating in a certain mode with in-band MDIO. Check the control register for the operating mode and enable the workaround accordingly.

Applied.