Low level debugging using CONFIG_EARLY_PRINTK=y, omap-debug branch removed
Hi all,
Recent commit 93fd03a8c6728b58879f8af20ffd55d9c32a778b added support for CONFIG_EARLY_PRINTK on ARM. Recent earlier kernels should work too by applying the patch in the commit above.
This means we can now get rid of the old printk.c hack in the omap-debug branch, so I've deleted that branch.
To use the earlyprintk, just do the following:
1. Make sure you have the necessary .config options set
CONFIG_DEBUG_LL=yCONFIG_EARLY_PRINTK=yCONFIG_OMAP_LL_DEBUG_UART1=y
# CONFIG_OMAP_LL_DEBUG_UART2 is not set
# CONFIG_OMAP_LL_DEBUG_UART3 is not set
The LL_DEBUG_UART above is typically 1, but it's 3 on Nokia boards.
2. Edit the kernel CMDLINE in your .config to have "debug earlyprintk"
Optionally if you have a JTAG console, you can use CONFIG_DEBUG_ICEDCC instead LL_DEBUG_UART.
I've also added these instructions to:
http://www.elinux.org/Debugging_OMAP_kernel
Regards,
Tony
Tony,
Quoted 29 lines
-----Original Message-----
From: [email protected] [mailto:[email protected]] On Behalf Of Tony Lindgren
Sent: Wednesday, December 16, 2009 6:24 AM
To: [email protected]
Subject: Low level debugging usingCONFIG_EARLY_PRINTK=y, omap-debug branch removedHi all,
Recent commit
93fd03a8c6728b58879f8af20ffd55d9c32a778badded support forCONFIG_EARLY_PRINTKon ARM. Recent earlier kernels should work too by applying the patch in the commit above.This means we can now get rid of the old
printk.chack in the omap-debug branch, so I've deleted that branch.To use the earlyprintk, just do the following:
1. Make sure you have the necessary .config options set
CONFIG_DEBUG_LL=yCONFIG_EARLY_PRINTK=yCONFIG_OMAP_LL_DEBUG_UART1=y
#CONFIG_OMAP_LL_DEBUG_UART2is not set
#CONFIG_OMAP_LL_DEBUG_UART3is not setThe
LL_DEBUG_UARTabove is typically 1, but it's 3 on Nokia boards.
Quoted 8 lines
2. Edit the kernel CMDLINE in your .config to have "debug earlyprintk"
Optionally if you have a JTAG console, you can use
CONFIG_DEBUG_ICEDCCinsteadLL_DEBUG_UART.I've also added these instructions to:
I tried this on couple of boards and at least it doesn't work with the options and mentioned bootargs. The low level debug prints are still not coming on console.
I haven't debugged it though.
Regards,
Santosh
Quoted 5 lines · Santosh
I tried this on couple of boards and at least it doesn't work with the options and mentioned bootargs. The low level debug prints are still not coming on console.
I haven't debugged it though.
It works on Beagle, at least. That's the only one that I've tested so far.
If you're using the kernel commandline from u-boot, don't forget to update it.
- Paul
Quoted 11 lines · Paul Walmsley
Quoted 5 lines · Santosh
I tried this on couple of boards and at least it doesn't work with the options and mentioned bootargs. The low level debug prints are still not coming on console.
I haven't debugged it though.
It works on Beagle, at least. That's the only one that I've tested so far.
I've been using the earlyprink patch for PM debug on several OMAP3 boards without any problems.
Kevin