saa7134 and üPD61151 MPEG2 coder
A message that is not in the archive (sent off-list or not yet received): [email protected]
A message that is not in the archive (sent off-list or not yet received): [email protected]
Hi Hans.
I finished saa7134 part of SPI. Please review saa7134-spi.c and diff saa7134-core and etc. I wrote config of SPI to board structure. Use this config for register master and slave devices.
SPI other then I2C, do not need call request_module. Udev do it. I spend 10 days for understanding :(
I need help with v4l2-common.c -> function v4l2_spi_new_subdev_board
The module of SPI slave loading after some time and spi device hasn't v4l2_subdev structure for v4l2_device_register_subdev.
Now I get kernel crash when call v4l2_device_register_subdev.
Need use a callback metod or other. I don't know.
Copy to Mauro Carvalho Chehab and mailing lists for review my code too.
Dmesg log without call v4l2_device_register_subdev.
[ 4.742279] Linux video capture interface: v2.00 [ 4.816171] saa7130/34: v4l2 driver version 0.2.15 loaded [ 4.816253] saa7134 0000:04:01.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19 [ 4.816304] saa7133[0]: found at 0000:04:01.0, rev: 209, irq: 19, latency: 32, mmio: 0xe5100000 [ 4.816363] saa7133[0]: subsystem: 5ace:7595, board: Beholder BeholdTV X7 [card=171,autodetected] [ 4.816430] saa7133[0]: board init: gpio is 200000 [ 4.816481] IRQ 19/saa7133[0]: IRQF_DISABLED is not guaranteed on shared IRQs [ 4.976010] saa7133[0]: i2c eeprom 00: ce 5a 95 75 54 20 00 00 00 00 00 00 00 00 00 01 [ 4.976635] saa7133[0]: i2c eeprom 10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 4.977231] saa7133[0]: i2c eeprom 20: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 4.977827] saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 4.978423] saa7133[0]: i2c eeprom 40: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 4.979019] saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 4.979615] saa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 4.980223] saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 4.980820] saa7133[0]: i2c eeprom 80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 4.981416] saa7133[0]: i2c eeprom 90: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 4.982012] saa7133[0]: i2c eeprom a0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 4.982608] saa7133[0]: i2c eeprom b0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 4.983204] saa7133[0]: i2c eeprom c0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 4.983800] saa7133[0]: i2c eeprom d0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 4.984437] saa7133[0]: i2c eeprom e0: 00 00 00 00 ff ff ff ff ff ff ff ff ff ff ff ff [ 4.985033] saa7133[0]: i2c eeprom f0: 42 54 56 30 30 30 30 ff ff ff ff ff ff ff ff ff [ 5.008041] tuner 1-0061: chip found @ 0xc2 (saa7133[0]) [ 5.024036] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 5.024109] HDA Intel 0000:00:1b.0: setting latency timer to 64 [ 5.066725] xc5000 1-0061: creating new instance [ 5.076009] xc5000: Successfully identified at address 0x61 [ 5.076060] xc5000: Firmware has not been loaded previously
[ 33.381216] saa7134 0000:04:01.0: spi master registered: bus_num=32766 num_chipselect=1 [ 33.381274] saa7133[0]: found muPD61151 MPEG encoder [ 33.381430] saa7133[0]: registered device video0 [v4l2] [ 33.381491] saa7133[0]: registered device vbi0 [ 33.381551] saa7133[0]: registered device radio0 [ 33.406256] saa7133[0]: registered device video1 [mpeg] [ 33.407628] upd61151_probe function [ 33.407672] Read test REG 0xD8 : [ 33.409502] REG = 0x0 [ 33.409547] Write test 0x03 to REG 0xD8 : [ 33.411353] Next read test REG 0xD8 : [ 33.413176] REG = 0x3 [ 33.431308] saa7134 ALSA driver for DMA sound loaded [ 33.431363] IRQ 19/saa7133[0]: IRQF_DISABLED is not guaranteed on shared IRQs [ 33.431425] saa7133[0]/alsa: saa7133[0] at 0xe5100000 irq 19 registered as card -1
[ 48.657067] xc5000: I2C write failed (len=4) [ 48.760018] xc5000: I2C write failed (len=4) [ 48.762960] xc5000: I2C read failed [ 48.763011] xc5000: I2C read failed [ 48.763054] xc5000: waiting for firmware upload (dvb-fe-xc5000-1.6.114.fw)... [ 48.763102] saa7134 0000:04:01.0: firmware: requesting dvb-fe-xc5000-1.6.114.fw [ 48.802473] xc5000: firmware read 12401 bytes. [ 48.802477] xc5000: firmware uploading... [ 49.328504] eth0: no IPv6 routers present [ 52.132007] xc5000: firmware upload complete... [ 53.366772] ------------[ cut here ]------------ [ 53.366820] kernel BUG at lib/kernel_lock.c:126! [ 53.366865] invalid opcode: 0000 [#1] SMP [ 53.366973] last sysfs file: /sys/class/firmware/0000:04:01.0/loading [ 53.367019] Modules linked in: ipv6 dm_snapshot dm_mirror dm_region_hash dm_log dm_mod loop saa7134_alsa upd61151 saa7134_empress ir_kbd_i2c snd_hda_codec_realtek xc5000 snd_hda_intel snd_hda_codec tuner snd_pcm_oss snd_mixer_oss snd_pcm snd_seq_dummy snd_seq_oss snd_seq_midi snd_rawmidi snd_seq_midi_event snd_seq saa7134 snd_timer ir_common v4l2_common videodev snd_seq_device v4l1_compat videobuf_dma_sg videobuf_core spi_bitbang psmouse snd ir_core serio_raw tveeprom soundcore parport_pc parport processor i2c_i801 button snd_page_alloc i2c_core intel_agp agpgart rng_core pcspkr evdev ext3 jbd mbcache sg sr_mod cdrom sd_mod ata_generic ata_piix libata scsi_mod ide_pci_generic ide_core ehci_hcd uhci_hcd r8169 mii usbcore thermal fan thermal_sys [last unloaded: scsi_wait_scan] [ 53.369624] [ 53.369666] Pid: 2659, comm: hald-probe-vide Not tainted (2.6.30.5 #1) G31M-ES2L [ 53.369721] EIP: 0060:[<c02f81e3>] EFLAGS: 00010286 CPU: 0 [ 53.369770] EIP is at unlock_kernel+0xd/0x24 [ 53.369814] EAX: f6bc26ac EBX: f6bc2000 ECX: f6bc26ac EDX: f707e4d0 [ 53.369860] ESI: 00000000 EDI: f6aa90c0 EBP: f6bc26ac ESP: f65b1e68 [ 53.369906] DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068 [ 53.369952] Process hald-probe-vide (pid: 2659, ti=f65b0000 task=f707e4d0 task.ti=f65b0000) [ 53.370008] Stack: [ 53.370049] f873e9c9 00000000 f687c804 f6aa90c0 00000000 f848e309 00000000 f6b4d680 [ 53.370298] f6b4d680 c0190049 f6aa90c0 f6a144e4 00000000 f6aa90c0 00000000 f6a144e4 [ 53.370298] c018ff24 c018c3b9 f701ef40 f6d11a5c f6aa90c0 f65b1f0c f65b1f0c 00008001 [ 53.370298] Call Trace: [ 53.370298] [<f873e9c9>] ? ts_open+0x8c/0x93 [saa7134_empress] [ 53.370298] [<f848e309>] ? v4l2_open+0x65/0x78 [videodev] [ 53.370298] [<c0190049>] ? chrdev_open+0x125/0x13c [ 53.370298] [<c018ff24>] ? chrdev_open+0x0/0x13c [ 53.370298] [<c018c3b9>] ? __dentry_open+0x119/0x208 [ 53.370298] [<c018c539>] ? nameidata_to_filp+0x29/0x3c [ 53.370298] [<c0197338>] ? do_filp_open+0x41e/0x7bc [ 53.370298] [<c017bb3c>] ? handle_mm_fault+0x294/0x5fd [ 53.370298] [<c019e267>] ? alloc_fd+0x52/0xb8 [ 53.370298] [<c018c1d1>] ? do_sys_open+0x44/0xb4 [ 53.370298] [<c018c285>] ? sys_open+0x1e/0x23 [ 53.370298] [<c0102f74>] ? sysenter_do_call+0x12/0x28 [ 53.370298] Code: 0f c1 05 e0 4b 3e c0 38 e0 74 09 f3 90 a0 e0 4b 3e c0 eb f3 64 a1 00 b0 43 c0 89 50 14 c3 64 8b 15 00 b0 43 c0 83 7a 14 00 79 04 <0f> 0b eb fe 8b 42 14 48 85 c0 89 42 14 79 07 f0 fe 05 e0 4b 3e [ 53.370298] EIP: [<c02f81e3>] unlock_kernel+0xd/0x24 SS:ESP 0068:f65b1e68 [ 53.374302] ---[ end trace 05965e9e089c46c7 ]---
With my best regards, Dmitry.
linux/drivers/media/video/saa7134/Makefile +2 -2
@@ -1,9 +1,9 @@ saa7134-objs := saa7134-cards.o saa7134-core.o saa7134-i2c.o \ saa7134-ts.o saa7134-tvaudio.o saa7134-vbi.o \ - saa7134-video.o saa7134-input.o + saa7134-video.o saa7134-input.o saa7134-spi.o -obj-$(CONFIG_VIDEO_SAA7134) += saa6752hs.o saa7134.o saa7134-empress.o +obj-$(CONFIG_VIDEO_SAA7134) += saa6752hs.o saa7134.o saa7134-empress.o upd61151.o obj-$(CONFIG_VIDEO_SAA7134_ALSA) += saa7134-alsa.o
linux/drivers/media/video/saa7134/saa7134-cards.c +39 -8
80 lines not on this page · raw message
linux/drivers/media/video/saa7134/saa7134-core.c +48 -3
78 lines not on this page · raw message
linux/drivers/media/video/saa7134/saa7134.h +44 -0
98 lines not on this page · raw message
linux/drivers/media/video/v4l2-common.c +82 -0
94 lines not on this page · raw message
linux/include/media/v4l2-common.h +22 -0
@@ -191,6 +191,28 @@/* ------------------------------------------------------------------------- */ +/* SPI Helper functions */ + +#include <linux/spi/spi.h> + +struct spi_device_id ; +struct spi_device ; + +/* Load an spi module and return an initialized v4l2_subdev struct. +Only call request_module if module_name != NULL. +The client_type argument is the name of the chip that's on the adapter. */ +struct v4l2_subdev *v4l2_spi_new_subdev (struct v4l2_device *v4l2_dev, +struct spi_master *spi,struct spi_board_info *spi_slave); + +struct v4l2_subdev *v4l2_spi_new_subdev_board (struct v4l2_device *v4l2_dev, +struct spi_master *spi,struct spi_board_info *info); + +/* Initialize an v4l2_subdev with data from an spi_device struct */ +void v4l2_spi_subdev_init (struct v4l2_subdev *sd,struct spi_device *spi, +const struct v4l2_subdev_ops *ops); + +/* ------------------------------------------------------------------------- */ +/* Note: these remaining ioctls/structs should be removed as well, but they are still used in tuner-simple.c (TUNER_SET_CONFIG), cx18/ivtv (RESET) and v4l2-int-device.h (v4l2_routing). To remove these ioctls some more cleanup
linux/include/media/v4l2-subdev.h +2 -0
@@ -387,6 +387,8 @@/* Set this flag if this subdev is a i2c device. */ #define V4L2_SUBDEV_FL_IS_I2C (1U << 0) +/* Set this flag if this subdev is a spi device. */ +#define V4L2_SUBDEV_FL_IS_SPI (1U << 1)/* Each instance of a subdev driver should create this struct, either stand-alone or embedded in a larger struct.
[ 4.742279] Linux video capture interface: v2.00 [ 4.816171] saa7130/34: v4l2 driver version 0.2.15 loaded [ 4.816253] saa7134 0000:04:01.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19 [ 4.816304] saa7133[0]: found at 0000:04:01.0, rev: 209, irq: 19, latency: 32, mmio: 0xe5100000 [ 4.816363] saa7133[0]: subsystem: 5ace:7595, board: Beholder BeholdTV X7 [card=171,autodetected] [ 4.816430] saa7133[0]: board init: gpio is 200000 [ 4.816481] IRQ 19/saa7133[0]: IRQF_DISABLED is not guaranteed on shared IRQs [ 4.976010] saa7133[0]: i2c eeprom 00: ce 5a 95 75 54 20 00 00 00 00 00 00 00 00 00 01 [ 4.976635] saa7133[0]: i2c eeprom 10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 4.977231] saa7133[0]: i2c eeprom 20: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 4.977827] saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 4.978423] saa7133[0]: i2c eeprom 40: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 4.979019] saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 4.979615] saa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 4.980223] saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 4.980820] saa7133[0]: i2c eeprom 80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 4.981416] saa7133[0]: i2c eeprom 90: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 4.982012] saa7133[0]: i2c eeprom a0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 4.982608] saa7133[0]: i2c eeprom b0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 4.983204] saa7133[0]: i2c eeprom c0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 4.983800] saa7133[0]: i2c eeprom d0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 4.984437] saa7133[0]: i2c eeprom e0: 00 00 00 00 ff ff ff ff ff ff ff ff ff ff ff ff [ 4.985033] saa7133[0]: i2c eeprom f0: 42 54 56 30 30 30 30 ff ff ff ff ff ff ff ff ff [ 5.008041] tuner 1-0061: chip found @ 0xc2 (saa7133[0]) [ 5.024036] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 5.024109] HDA Intel 0000:00:1b.0: setting latency timer to 64 [ 5.066725] xc5000 1-0061: creating new instance [ 5.076009] xc5000: Successfully identified at address 0x61 [ 5.076060] xc5000: Firmware has not been loaded previously
[ 33.381216] saa7134 0000:04:01.0: spi master registered: bus_num=32766 num_chipselect=1 [ 33.381274] saa7133[0]: found muPD61151 MPEG encoder [ 33.381430] saa7133[0]: registered device video0 [v4l2] [ 33.381491] saa7133[0]: registered device vbi0 [ 33.381551] saa7133[0]: registered device radio0 [ 33.406256] saa7133[0]: registered device video1 [mpeg] [ 33.407628] upd61151_probe function [ 33.407672] Read test REG 0xD8 : [ 33.409502] REG = 0x0 [ 33.409547] Write test 0x03 to REG 0xD8 : [ 33.411353] Next read test REG 0xD8 : [ 33.413176] REG = 0x3 [ 33.431308] saa7134 ALSA driver for DMA sound loaded [ 33.431363] IRQ 19/saa7133[0]: IRQF_DISABLED is not guaranteed on shared IRQs [ 33.431425] saa7133[0]/alsa: saa7133[0] at 0xe5100000 irq 19 registered as card -1
[ 48.657067] xc5000: I2C write failed (len=4) [ 48.760018] xc5000: I2C write failed (len=4) [ 48.762960] xc5000: I2C read failed [ 48.763011] xc5000: I2C read failed [ 48.763054] xc5000: waiting for firmware upload (dvb-fe-xc5000-1.6.114.fw)... [ 48.763102] saa7134 0000:04:01.0: firmware: requesting dvb-fe-xc5000-1.6.114.fw [ 48.802473] xc5000: firmware read 12401 bytes. [ 48.802477] xc5000: firmware uploading... [ 49.328504] eth0: no IPv6 routers present [ 52.132007] xc5000: firmware upload complete... [ 53.366772] ------------[ cut here ]------------ [ 53.366820] kernel BUG at lib/kernel_lock.c:126! [ 53.366865] invalid opcode: 0000 [#1] SMP [ 53.366973] last sysfs file: /sys/class/firmware/0000:04:01.0/loading [ 53.367019] Modules linked in: ipv6 dm_snapshot dm_mirror dm_region_hash dm_log dm_mod loop saa7134_alsa upd61151 saa7134_empress ir_kbd_i2c snd_hda_codec_realtek xc5000 snd_hda_intel snd_hda_codec tuner snd_pcm_oss snd_mixer_oss snd_pcm snd_seq_dummy snd_seq_oss snd_seq_midi snd_rawmidi snd_seq_midi_event snd_seq saa7134 snd_timer ir_common v4l2_common videodev snd_seq_device v4l1_compat videobuf_dma_sg videobuf_core spi_bitbang psmouse snd ir_core serio_raw tveeprom soundcore parport_pc parport processor i2c_i801 button snd_page_alloc i2c_core intel_agp agpgart rng_core pcspkr evdev ext3 jbd mbcache sg sr_mod cdrom sd_mod ata_generic ata_piix libata scsi_mod ide_pci_generic ide_core ehci_hcd uhci_hcd r8169 mii usbcore thermal fan thermal_sys [last unloaded: scsi_wait_scan] [ 53.369624] [ 53.369666] Pid: 2659, comm: hald-probe-vide Not tainted (2.6.30.5 #1) G31M-ES2L [ 53.369721] EIP: 0060:[<c02f81e3>] EFLAGS: 00010286 CPU: 0 [ 53.369770] EIP is at unlock_kernel+0xd/0x24 [ 53.369814] EAX: f6bc26ac EBX: f6bc2000 ECX: f6bc26ac EDX: f707e4d0 [ 53.369860] ESI: 00000000 EDI: f6aa90c0 EBP: f6bc26ac ESP: f65b1e68 [ 53.369906] DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068 [ 53.369952] Process hald-probe-vide (pid: 2659, ti=f65b0000 task=f707e4d0 task.ti=f65b0000) [ 53.370008] Stack: [ 53.370049] f873e9c9 00000000 f687c804 f6aa90c0 00000000 f848e309 00000000 f6b4d680 [ 53.370298] f6b4d680 c0190049 f6aa90c0 f6a144e4 00000000 f6aa90c0 00000000 f6a144e4 [ 53.370298] c018ff24 c018c3b9 f701ef40 f6d11a5c f6aa90c0 f65b1f0c f65b1f0c 00008001 [ 53.370298] Call Trace: [ 53.370298] [<f873e9c9>] ? ts_open+0x8c/0x93 [saa7134_empress] [ 53.370298] [<f848e309>] ? v4l2_open+0x65/0x78 [videodev] [ 53.370298] [<c0190049>] ? chrdev_open+0x125/0x13c [ 53.370298] [<c018ff24>] ? chrdev_open+0x0/0x13c [ 53.370298] [<c018c3b9>] ? __dentry_open+0x119/0x208 [ 53.370298] [<c018c539>] ? nameidata_to_filp+0x29/0x3c [ 53.370298] [<c0197338>] ? do_filp_open+0x41e/0x7bc [ 53.370298] [<c017bb3c>] ? handle_mm_fault+0x294/0x5fd [ 53.370298] [<c019e267>] ? alloc_fd+0x52/0xb8 [ 53.370298] [<c018c1d1>] ? do_sys_open+0x44/0xb4 [ 53.370298] [<c018c285>] ? sys_open+0x1e/0x23 [ 53.370298] [<c0102f74>] ? sysenter_do_call+0x12/0x28 [ 53.370298] Code: 0f c1 05 e0 4b 3e c0 38 e0 74 09 f3 90 a0 e0 4b 3e c0 eb f3 64 a1 00 b0 43 c0 89 50 14 c3 64 8b 15 00 b0 43 c0 83 7a 14 00 79 04 <0f> 0b eb fe 8b 42 14 48 85 c0 89 42 14 79 07 f0 fe 05 e0 4b 3e [ 53.370298] EIP: [<c02f81e3>] unlock_kernel+0xd/0x24 SS:ESP 0068:f65b1e68 [ 53.374302] ---[ end trace 05965e9e089c46c7 ]---
/*
*
* Device driver for philips saa7134 based TV cards
* SPI software interface support
*
* (c) 2009 Beholder Intl. Ltd. Dmitry Belimov <[email protected]> *
* Important: now support ONLY SPI_MODE_0, see FIXME
*
* This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation; either version 2 of the License, or * (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*/
#include "saa7134-reg.h"
#include "saa7134.h"
#include <media/v4l2-common.h>
/* ----------------------------------------------------------- */
static unsigned int spi_debug; module_param(spi_debug, int, 0644); MODULE_PARM_DESC(spi_debug,"enable debug messages [spi]");
#define d1printk if (1 == spi_debug) printk
#define d2printk if (2 == spi_debug) printk
static inline void spidelay(unsigned d)
{
udelay(d);
}static inline struct saa7134_spi_gpio *to_sb(struct spi_device *spi)
{
return spi_master_get_devdata(spi->master);
}static inline void setsck(struct spi_device *dev, int on)
{
struct saa7134_spi_gpio *sb = to_sb(dev);
saa7134_set_gpio(sb->controller_data, sb->controller_data->spi.clock, on ? 1 : 0);
}static inline void setmosi(struct spi_device *dev, int on)
{
struct saa7134_spi_gpio *sb = to_sb(dev);
saa7134_set_gpio(sb->controller_data, sb->controller_data->spi.mosi, on ? 1 : 0);
}static inline u32 getmiso(struct spi_device *dev)
{
struct saa7134_spi_gpio *sb = to_sb(dev);
unsigned long status;
status = saa7134_get_gpio(sb->controller_data);
if ( status & (1 << sb->controller_data->spi.miso))
return 1;
else
return 0;
}#define EXPAND_BITBANG_TXRX 1
#include <linux/spi/spi_bitbang.h>
static void saa7134_spi_gpio_chipsel(struct spi_device *dev, int on)
{
struct saa7134_spi_gpio *sb = to_sb(dev);
if (on)
{
/* FIXME: set clock to zero by default, only SPI_MODE_0 compatible */
saa7134_set_gpio(sb->controller_data, sb->controller_data->spi.clock, 0);
saa7134_set_gpio(sb->controller_data, sb->controller_data->spi.cs, 0);
}
else
saa7134_set_gpio(sb->controller_data, sb->controller_data->spi.cs, 1);
}/* Our actual bitbanger routine. */
static u32 saa7134_txrx(struct spi_device *spi, unsigned nsecs, u32 word, u8 bits)
{
return bitbang_txrx_be_cpha0(spi, nsecs, 0, word, bits);
}static int saa7134_setup(struct spi_device *spi, struct spi_transfer *t)
{
return spi_bitbang_setup_transfer(spi, t);
}int saa7134_spi_register(struct saa7134_dev *dev, struct spi_board_info *info)
{
struct spi_master *master = NULL;
struct saa7134_spi_gpio *sb = NULL;
int ret = 0;
master = spi_alloc_master(&dev->pci->dev, sizeof(struct saa7134_spi_gpio));
if (master == NULL) {
dev_err(&dev->pci->dev, "failed to allocate spi master\n");
ret = -ENOMEM;
goto err;
}
sb = spi_master_get_devdata(master);
master->num_chipselect = dev->spi.num_chipselect;
master->bus_num = -1;
sb->master = spi_master_get(master);
sb->bitbang.master = sb->master;
sb->bitbang.master->bus_num = -1;
sb->bitbang.master->num_chipselect = dev->spi.num_chipselect;
sb->bitbang.chipselect = saa7134_spi_gpio_chipsel;
sb->bitbang.txrx_word[SPI_MODE_0] = saa7134_txrx;
sb->bitbang.setup_transfer = saa7134_setup;
/* set state of spi pins */
saa7134_set_gpio(dev, dev->spi.cs, 1);
/* FIXME: set clock to zero by default, only SPI_MODE_0 compatible */
saa7134_set_gpio(dev, dev->spi.clock, 0);
saa7134_set_gpio(dev, dev->spi.mosi, 1);
saa7134_set_gpio(dev, dev->spi.miso, 3);
/* start SPI bitbang master */
ret = spi_bitbang_start(&sb->bitbang);
if (ret) {
dev_err(&dev->pci->dev, "Failed to register SPI master\n");
goto err_no_bitbang;
}
dev_info(&dev->pci->dev,
"spi master registered: bus_num=%d num_chipselect=%d\n",
master->bus_num, master->num_chipselect);
sb->controller_data = dev;
info->bus_num = sb->master->bus_num;
info->controller_data = master;
dev->spi_adap = master;err_no_bitbang:
spi_master_put(master); err: return ret; }
int saa7134_spi_unregister(struct saa7134_dev *dev)
{
struct saa7134_spi_gpio *sb = spi_master_get_devdata(dev->spi_adap);
spi_bitbang_stop(&sb->bitbang);
spi_master_put(sb->master);
return 0;
}/*
* Overrides for Emacs so that we follow Linus's tabbing style.
* ---------------------------------------------------------------------------
* Local variables:
* c-basic-offset: 8
* End:
*/
/*
upd61151 - driver for the uPD61151 by NEC
Copyright (C) Beholder Intl. Ltd. Dmitry Belimov <[email protected]>
Based on the saa6752s.c driver.
Copyright (C) 2004 Andrew de Quincey
This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License vs published by the Free Software Foundation; either version 2 of the License, or (at your option) any later version.
This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details.
You should have received a copy of the GNU General Public License along with this program; if not, write to the Free Software Foundation, Inc., 675 Mvss Ave, Cambridge, MA 02139, USA.
*/
#include <linux/init.h>
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/device.h>
#include <linux/sysfs.h>
#include <linux/string.h>
#include <linux/timer.h>
#include <linux/delay.h>
#include <linux/errno.h>
#include <linux/slab.h>
#include <linux/poll.h>
#include <linux/spi/spi.h>
#include <linux/types.h>
//#include <linux/mod_devicetable.h>
#include "compat.h"
#include <linux/videodev2.h>
#include <media/v4l2-device.h>
#include <media/v4l2-common.h>
#include <media/v4l2-chip-ident.h>
#include <media/upd61151.h>
#include <linux/crc32.h>
#include "saa7134.h"
#define MPEG_VIDEO_TARGET_BITRATE_MAX 27000 #define MPEG_VIDEO_MAX_BITRATE_MAX 27000 #define MPEG_TOTAL_TARGET_BITRATE_MAX 27000
#define MPEG_PID_MAX ((1 << 14) - 1)
#define DRVNAME "upd61151"
MODULE_DESCRIPTION("device driver for uPD61151 MPEG2 encoder"); MODULE_AUTHOR("Dmitry V Belimov"); MODULE_LICENSE("GPL");
enum upd61151_videoformat {
UPD61151_VF_D1 = 0, /* standard D1 video format: 720x576 */
UPD61151_VF_2_3_D1 = 1,/* 2/3D1 video format: 480x576 */
UPD61151_VF_1_2_D1 = 2,/* 1/2D1 video format: 352x576 */
UPD61151_VF_SIF = 3, /* SIF video format: 352x288 */
UPD61151_VF_UNKNOWN,
};struct upd61151_mpeg_params {
/* transport streams */
__u16 ts_pid_pmt;
__u16 ts_pid_audio;
__u16 ts_pid_video;
__u16 ts_pid_pcr;
/* audio */
enum v4l2_mpeg_audio_encoding au_encoding;
enum v4l2_mpeg_audio_l2_bitrate au_l2_bitrate;
/* video */
enum v4l2_mpeg_video_aspect vi_aspect;
enum v4l2_mpeg_video_bitrate_mode vi_bitrate_mode;
__u32 vi_bitrate;
__u32 vi_bitrate_peak;
};static const struct v4l2_format v4l2_format_table[] =
{
[UPD61151_VF_D1] =
{ .fmt = { .pix = { .width = 720, .height = 576 }}},
[UPD61151_VF_2_3_D1] =
{ .fmt = { .pix = { .width = 480, .height = 576 }}},
[UPD61151_VF_1_2_D1] =
{ .fmt = { .pix = { .width = 352, .height = 576 }}},
[UPD61151_VF_SIF] =
{ .fmt = { .pix = { .width = 352, .height = 288 }}},
[UPD61151_VF_UNKNOWN] =
{ .fmt = { .pix = { .width = 0, .height = 0}}},
};struct upd61151_state {
struct v4l2_subdev sd;
// struct spi_board_info info;
int chip;
u32 revision;
struct upd61151_mpeg_params params;
enum upd61151_videoformat video_format;
v4l2_std_id standard;
};enum upd61151_command {
UPD61151_COMMAND_RESET = 0,
UPD61151_COMMAND_STOP = 1,
UPD61151_COMMAND_START = 2,
UPD61151_COMMAND_PAUSE = 3,
UPD61151_COMMAND_RECONFIGURE = 4,
UPD61151_COMMAND_SLEEP = 5,
UPD61151_COMMAND_RECONFIGURE_FORCE = 6,
UPD61151_COMMAND_MAX
};#if 0
static int write_reg( ??struct device *dev??, int address, unsigned char data)
{
struct spi_device *spi = to_spi_device(dev);
unsigned char buf[2];
buf[0] = address & 0x7f;
buf[1] = data;
return spi_write(spi, buf, ARRAY_SIZE(buf));
}static int read_regs( ??struct device *dev??, unsigned char *regs, int no_regs)
{
struct spi_device *spi = to_spi_device(dev);
u8 txbuf[1], rxbuf[1];
int k, ret;
ret = 0;
for (k = 0; ret == 0 && k < no_regs; k++) {
txbuf[0] = 0x80 | regs[k];
ret = spi_write_then_read(spi, txbuf, 1, rxbuf, 1);
regs[k] = rxbuf[0];
}
return ret;
}#endif
static struct upd61151_mpeg_params param_defaults =
{
.ts_pid_pmt = 16,
.ts_pid_video = 260,
.ts_pid_audio = 256,
.ts_pid_pcr = 259,
.vi_aspect = V4L2_MPEG_VIDEO_ASPECT_4x3,
.vi_bitrate = 4000,
.vi_bitrate_peak = 6000,
.vi_bitrate_mode = V4L2_MPEG_VIDEO_BITRATE_MODE_VBR,
.au_encoding = V4L2_MPEG_AUDIO_ENCODING_LAYER_2,
.au_l2_bitrate = V4L2_MPEG_AUDIO_L2_BITRATE_256K,
};#if 0
static int upd61151_chip_command(struct spi_device *spi,
enum upd61151_command command)
{
printk("DEBUG uPD61151: upd61151_chip_command\n");
return 0;
}static int upd61151_set_bitrate(struct spi_device *spi,
struct upd61151_state *h)
{
printk("DEBUG uPD61151: upd61151_set_bitrate\n");
return 0;
}#endif
static int upd61151_queryctrl(struct v4l2_subdev *sd, struct v4l2_queryctrl *qctrl) {
printk("DEBUG uPD61151: upd61151_queryctrl\n");
return 0;
}static int upd61151_querymenu(struct v4l2_subdev *sd, struct v4l2_querymenu *qmenu) {
printk("DEBUG uPD61151: upd61151_querymenu\n");
return 0;
}static int upd61151_init(struct v4l2_subdev *sd, u32 flags) {
printk("DEBUG uPD61151: upd61151_init\n");
return 0;
}static int upd61151_do_ext_ctrls(struct v4l2_subdev *sd, struct v4l2_ext_controls *ctrls, int set) {
printk("DEBUG uPD61151: upd61151_do_ext_ctrls\n");
return 0;
}static int upd61151_s_ext_ctrls(struct v4l2_subdev *sd, struct v4l2_ext_controls *ctrls) {
printk("DEBUG uPD61151: upd61151_s_ext_ctrls\n");
return upd61151_do_ext_ctrls(sd, ctrls, 1);
}static int upd61151_try_ext_ctrls(struct v4l2_subdev *sd, struct v4l2_ext_controls *ctrls) {
printk("DEBUG uPD61151: upd61151_s_ext_ctrls\n");
return upd61151_do_ext_ctrls(sd, ctrls, 0);
}static int upd61151_g_ext_ctrls(struct v4l2_subdev *sd, struct v4l2_ext_controls *ctrls) {
printk("DEBUG uPD61151: upd61151_g_ext_ctrls\n");
return 0;
}static int upd61151_g_fmt(struct v4l2_subdev *sd, struct v4l2_format *f) {
printk("DEBUG uPD61151: upd61151_g_fmt\n");
return 0;
}static int upd61151_s_fmt(struct v4l2_subdev *sd, struct v4l2_format *f) {
printk("DEBUG uPD61151: upd61151_s_fmt\n");
return 0;
}static int upd61151_s_std(struct v4l2_subdev *sd, v4l2_std_id std) {
printk("DEBUG uPD61151: upd61151_s_std\n");
return 0;
}static int upd61151_g_chip_ident(struct v4l2_subdev *sd, struct v4l2_dbg_chip_ident *chip) {
printk("DEBUG uPD61151: upd61151_g_chip_ident\n");
return 0;
}/* ----------------------------------------------------------------------- */
static const struct v4l2_subdev_core_ops upd61151_core_ops = {
.g_chip_ident = upd61151_g_chip_ident,
.init = upd61151_init,
.queryctrl = upd61151_queryctrl,
.querymenu = upd61151_querymenu,
.g_ext_ctrls = upd61151_g_ext_ctrls,
.s_ext_ctrls = upd61151_s_ext_ctrls,
.try_ext_ctrls = upd61151_try_ext_ctrls,
.s_std = upd61151_s_std,
};static const struct v4l2_subdev_video_ops upd61151_video_ops = {
.s_fmt = upd61151_s_fmt,
.g_fmt = upd61151_g_fmt,
};static const struct v4l2_subdev_ops upd61151_ops = {
.core = &upd61151_core_ops,
.video = &upd61151_video_ops,
};static int __devinit upd61151_probe(struct spi_device *spi)
{
struct upd61151_state *h = kzalloc(sizeof(*h), GFP_KERNEL);
struct v4l2_subdev *sd;
u8 tx_buf_r[2];
u8 tx_buf_w[2];
u8 rx_buf[2];
int status;printk("upd61151_probe function\n");
printk("Read test REG 0xD8 :\n");
tx_buf_r[0] = ((0xD8 >> 2) << 2) | 0x02;
status = spi_write_then_read(spi, tx_buf_r, 1, rx_buf, 1);
if (status < 0) {
printk("spi_write_then_read failed with status %d\n",
status);
// goto out;
}printk("REG = 0x%X\n",rx_buf[0]);
printk("Write test 0x03 to REG 0xD8 :\n");
tx_buf_w[0] = ((0xD8 >> 2) << 2); tx_buf_w[1] = 0x03; spi_write(spi, tx_buf_w, 2);
printk("Next read test REG 0xD8 :\n");
status = spi_write_then_read(spi, tx_buf_r, 1, rx_buf, 1);
if (status < 0) {
printk("spi_write_then_read failed with status %d\n",
status);
// goto out;
}printk("REG = 0x%X\n",rx_buf[0]);
if (h == NULL) return -ENOMEM; sd = &h->sd;
// v4l2_spi_subdev_init(sd, spi, &upd61151_ops);
spi_set_drvdata(spi, h);
/* function for detect a chip here */
// h->chip = upd61151_detect(h);
h->params = param_defaults; h->standard = 0; /* Assume 625 input lines */ return 0; }
static int __devexit upd61151_remove(struct spi_device *spi)
{
struct upd61151_state *h = spi_get_drvdata(spi);
printk("upd61151_remove function\n");
v4l2_device_unregister_subdev(&h->sd);
kfree(&h->sd);
spi_unregister_device(spi);
return 0;
}#if 0
static const struct spi_device_id upd61151_ids[] = {
{ "upd61151", 1 },
{ "upd61152", 2 },
{ },
};MODULE_DEVICE_TABLE(spi, upd61151_ids);
#endif
static struct spi_driver upd61151_driver = {
.driver = {
.name = DRVNAME,
.bus = &spi_bus_type,
.owner = THIS_MODULE,
},
// .id_table = upd61151_ids,
.probe = upd61151_probe, .remove = __devexit_p(upd61151_remove), };
static int __init init_upd61151(void)
{
return spi_register_driver(&upd61151_driver);
}module_init(init_upd61151);
static void __exit exit_upd61151(void)
{
spi_unregister_driver(&upd61151_driver);
}module_exit(exit_upd61151);
/*
* Overrides for Emacs so that we follow Linus's tabbing style.
* ---------------------------------------------------------------------------
* Local variables:
* c-basic-offset: 8
* End:
*/
/*
upd61151.h - definition for muPD61151 MPEG encoder
Copyright (C) Beholder Intl. Ltd. Dmitry Belimov <[email protected]>
This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation; either version 2 of the License, or (at your option) any later version.
This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details.
You should have received a copy of the GNU General Public License along with this program; if not, write to the Free Software Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*/
#if 0 /* ndef _UPD61151_H */
#define _UPD61151_H
#include <linux/firmware.h>
#define MUPD61151_DEFAULT_PS_FIRMWARE "D61151_PS_64_byte_7133_v22_031031.bin" #define MUPD61151_DEFAULT_PS_FIRMWARE_SIZE 97002
#define MUPD61151_DEFAULT_AUDIO_FIRMWARE "audrey_MPE_V1r51.bin" #define MUPD61151_DEFAULT_AUDIO_FIRMWARE_SIZE 40064
enum mpeg_video_bitrate_mode {
MPEG_VIDEO_BITRATE_MODE_VBR = 0, /* Variable bitrate */ MPEG_VIDEO_BITRATE_MODE_CBR = 1, /* Constant bitrate */
MPEG_VIDEO_BITRATE_MODE_MAX
};
enum mpeg_audio_bitrate {
MPEG_AUDIO_BITRATE_256 = 0, /* 256 kBit/sec */
MPEG_AUDIO_BITRATE_384 = 1, /* 384 kBit/sec */
MPEG_AUDIO_BITRATE_MAX
};enum mpeg_video_format {
MPEG_VIDEO_FORMAT_D1 = 0,
MPEG_VIDEO_FORMAT_2_3_D1 = 1,
MPEG_VIDEO_FORMAT_1_2_D1 = 2,
MPEG_VIDEO_FORMAT_SIF = 3,
MPEG_VIDEO_FORMAT_MAX
};#define MPEG_VIDEO_TARGET_BITRATE_MAX 27000
#define MPEG_VIDEO_MAX_BITRATE_MAX 27000
#define MPEG_TOTAL_BITRATE_MAX 27000
#define MPEG_PID_MAX ((1 << 14) - 1)
struct mpeg_params {
enum mpeg_video_bitrate_mode video_bitrate_mode;
unsigned int video_target_bitrate;
unsigned int video_max_bitrate; // only used for VBR
enum mpeg_audio_bitrate audio_bitrate;
unsigned int total_bitrate;
unsigned int pmt_pid;
unsigned int video_pid;
unsigned int audio_pid;
unsigned int pcr_pid;
enum mpeg_video_format video_format;
};#endif // _UPD61151_H
/*
* Local variables:
* c-basic-offset: 8
* End:
*/
Re: saa7134 and μPD61151 MPEG2 coder
Hi Dmitri,
Just a quick note: the video4linux mailinglist is obsolete, just use linux-media.
Quoted 7 lines · On Wednesday 27 January 2010 06:36:37 Dmitri Belimov wrote:
Hi Hans.
I finished saa7134 part of SPI. Please review
saa7134-spi.cand diff saa7134-core and etc. I wrote config of SPI to board structure. Use this config for register master and slave devices.SPI other then I2C, do not need call
request_module. Udev do it. I spend 10 days for understanding :(
I'm almost certain that spi works the same way as i2c and that means that you must call request_module. Yes, udev will load it for you, but that is a delayed
load: i.e. the module may not be loaded when we need it. The idea behind this is that usually i2c or spi modules are standalone, but in the context of v4l such modules are required to be present before the bridge can properly configure itself.
The easiest way to ensure the correct load sequence is to do a request_module at the start.
Now, I haven't compiled this, but I think this will work:
struct v4l2_subdev *v4l2_spi_new_subdev(struct v4l2_device *v4l2_dev,
struct spi_master *master, struct spi_board_info *info)
{
struct v4l2_subdev *sd = NULL;
struct spi_device *spi;
BUG_ON(!v4l2_dev);
if (module_name)
request_module(module_name);
spi = spi_new_device(master, info);
if (spi == NULL || spi->dev.driver == NULL)
goto error;
if (!try_module_get(spi->dev.driver->owner))
goto error;
sd = spi_get_drvdata(spi);
/* Register with the v4l2_device which increases the module's
use count as well. */
if (v4l2_device_register_subdev(v4l2_dev, sd))
sd = NULL;
/* Decrease the module use count to match the first try_module_get. */
module_put(spi->dev.driver->owner);error:
/* If we have a client but no subdev, then something went wrong and
we must unregister the client. */
if (spi && sd == NULL)
spi_unregister_device(spi);
return sd;
}EXPORT_SYMBOL_GPL(v4l2_spi_new_subdev);
Note that you mixed up the spi master and spi client in your original code. So it is no wonder you experienced crashes.
Also note that there is no need for a separate v4l2_spi_new_subdev_board function.
And in v4l2_spi_subdev_init() you should use spi_set_drvdata instead of dev_set_drvdata.
I hope this helps.
Regards,
Hans
Quoted 105 lines
I need help with
v4l2-common.c-> functionv4l2_spi_new_subdev_board
The module of SPI slave loading after some time and spi device hasn'tv4l2_subdevstructure forv4l2_device_register_subdev.Now I get kernel crash when call
v4l2_device_register_subdev.Need use a callback metod or other. I don't know.
Copy to Mauro Carvalho Chehab and mailing lists for review my code too.
Dmesg log without call
v4l2_device_register_subdev.[ 4.742279] Linux video capture interface: v2.00 [ 4.816171] saa7130/34: v4l2 driver version 0.2.15 loaded [ 4.816253] saa7134 0000:04:01.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19 [ 4.816304] saa7133[0]: found at 0000:04:01.0, rev: 209, irq: 19, latency: 32, mmio: 0xe5100000 [ 4.816363] saa7133[0]: subsystem: 5ace:7595, board: Beholder BeholdTV X7 [card=171,autodetected] [ 4.816430] saa7133[0]: board init: gpio is 200000 [ 4.816481] IRQ 19/saa7133[0]: IRQF_DISABLED is not guaranteed on shared IRQs [ 4.976010] saa7133[0]: i2c eeprom 00: ce 5a 95 75 54 20 00 00 00 00 00 00 00 00 00 01 [ 4.976635] saa7133[0]: i2c eeprom 10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 4.977231] saa7133[0]: i2c eeprom 20: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 4.977827] saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 4.978423] saa7133[0]: i2c eeprom 40: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 4.979019] saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 4.979615] saa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 4.980223] saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 4.980820] saa7133[0]: i2c eeprom 80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 4.981416] saa7133[0]: i2c eeprom 90: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 4.982012] saa7133[0]: i2c eeprom a0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 4.982608] saa7133[0]: i2c eeprom b0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 4.983204] saa7133[0]: i2c eeprom c0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 4.983800] saa7133[0]: i2c eeprom d0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 4.984437] saa7133[0]: i2c eeprom e0: 00 00 00 00 ff ff ff ff ff ff ff ff ff ff ff ff [ 4.985033] saa7133[0]: i2c eeprom f0: 42 54 56 30 30 30 30 ff ff ff ff ff ff ff ff ff [ 5.008041] tuner 1-0061: chip found @ 0xc2 (saa7133[0]) [ 5.024036] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 5.024109] HDA Intel 0000:00:1b.0: setting latency timer to 64 [ 5.066725] xc5000 1-0061: creating new instance [ 5.076009] xc5000: Successfully identified at address 0x61 [ 5.076060] xc5000: Firmware has not been loaded previously[ 33.381216] saa7134 0000:04:01.0: spi master registered: bus_num=32766 num_chipselect=1 [ 33.381274] saa7133[0]: found muPD61151 MPEG encoder [ 33.381430] saa7133[0]: registered device video0 [v4l2] [ 33.381491] saa7133[0]: registered device vbi0 [ 33.381551] saa7133[0]: registered device radio0 [ 33.406256] saa7133[0]: registered device video1 [mpeg] [ 33.407628] upd61151_probe function [ 33.407672] Read test REG 0xD8 : [ 33.409502] REG = 0x0 [ 33.409547] Write test 0x03 to REG 0xD8 : [ 33.411353] Next read test REG 0xD8 : [ 33.413176] REG = 0x3 [ 33.431308] saa7134 ALSA driver for DMA sound loaded [ 33.431363] IRQ 19/saa7133[0]: IRQF_DISABLED is not guaranteed on shared IRQs [ 33.431425] saa7133[0]/alsa: saa7133[0] at 0xe5100000 irq 19 registered as card -1[ 48.657067] xc5000: I2C write failed (len=4) [ 48.760018] xc5000: I2C write failed (len=4) [ 48.762960] xc5000: I2C read failed [ 48.763011] xc5000: I2C read failed [ 48.763054] xc5000: waiting for firmware upload (dvb-fe-xc5000-1.6.114.fw)... [ 48.763102] saa7134 0000:04:01.0: firmware: requesting dvb-fe-xc5000-1.6.114.fw [ 48.802473] xc5000: firmware read 12401 bytes. [ 48.802477] xc5000: firmware uploading... [ 49.328504] eth0: no IPv6 routers present [ 52.132007] xc5000: firmware upload complete... [ 53.366772] ------------[ cut here ]------------ [ 53.366820] kernel BUG at lib/kernel_lock.c:126! [ 53.366865] invalid opcode: 0000 [#1] SMP [ 53.366973] last sysfs file: /sys/class/firmware/0000:04:01.0/loading [ 53.367019] Modules linked in: ipv6 dm_snapshot dm_mirror dm_region_hash dm_log dm_mod loop saa7134_alsa upd61151 saa7134_empress ir_kbd_i2c snd_hda_codec_realtek xc5000 snd_hda_intel snd_hda_codec tuner snd_pcm_oss snd_mixer_oss snd_pcm snd_seq_dummy snd_seq_oss snd_seq_midi snd_rawmidi snd_seq_midi_event snd_seq saa7134 snd_timer ir_common v4l2_common videodev snd_seq_device v4l1_compat videobuf_dma_sg videobuf_core spi_bitbang psmouse snd ir_core serio_raw tveeprom soundcore parport_pc parport processor i2c_i801 button snd_page_alloc i2c_core intel_agp agpgart rng_core pcspkr evdev ext3 jbd mbcache sg sr_mod cdrom sd_mod ata_generic ata_piix libata scsi_mod ide_pci_generic ide_core ehci_hcd uhci_hcd r8169 mii usbcore thermal fan thermal_sys [last unloaded: scsi_wait_scan] [ 53.369624] [ 53.369666] Pid: 2659, comm: hald-probe-vide Not tainted (2.6.30.5 #1) G31M-ES2L [ 53.369721] EIP: 0060:[<c02f81e3>] EFLAGS: 00010286 CPU: 0 [ 53.369770] EIP is at unlock_kernel+0xd/0x24 [ 53.369814] EAX: f6bc26ac EBX: f6bc2000 ECX: f6bc26ac EDX: f707e4d0 [ 53.369860] ESI: 00000000 EDI: f6aa90c0 EBP: f6bc26ac ESP: f65b1e68 [ 53.369906] DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068 [ 53.369952] Process hald-probe-vide (pid: 2659, ti=f65b0000 task=f707e4d0 task.ti=f65b0000) [ 53.370008] Stack: [ 53.370049] f873e9c9 00000000 f687c804 f6aa90c0 00000000 f848e309 00000000 f6b4d680 [ 53.370298] f6b4d680 c0190049 f6aa90c0 f6a144e4 00000000 f6aa90c0 00000000 f6a144e4 [ 53.370298] c018ff24 c018c3b9 f701ef40 f6d11a5c f6aa90c0 f65b1f0c f65b1f0c 00008001 [ 53.370298] Call Trace: [ 53.370298] [<f873e9c9>] ? ts_open+0x8c/0x93 [saa7134_empress] [ 53.370298] [<f848e309>] ? v4l2_open+0x65/0x78 [videodev] [ 53.370298] [<c0190049>] ? chrdev_open+0x125/0x13c [ 53.370298] [<c018ff24>] ? chrdev_open+0x0/0x13c [ 53.370298] [<c018c3b9>] ? __dentry_open+0x119/0x208 [ 53.370298] [<c018c539>] ? nameidata_to_filp+0x29/0x3c [ 53.370298] [<c0197338>] ? do_filp_open+0x41e/0x7bc [ 53.370298] [<c017bb3c>] ? handle_mm_fault+0x294/0x5fd [ 53.370298] [<c019e267>] ? alloc_fd+0x52/0xb8 [ 53.370298] [<c018c1d1>] ? do_sys_open+0x44/0xb4 [ 53.370298] [<c018c285>] ? sys_open+0x1e/0x23 [ 53.370298] [<c0102f74>] ? sysenter_do_call+0x12/0x28 [ 53.370298] Code: 0f c1 05 e0 4b 3e c0 38 e0 74 09 f3 90 a0 e0 4b 3e c0 eb f3 64 a1 00 b0 43 c0 89 50 14 c3 64 8b 15 00 b0 43 c0 83 7a 14 00 79 04 <0f> 0b eb fe 8b 42 14 48 85 c0 89 42 14 79 07 f0 fe 05 e0 4b 3e [ 53.370298] EIP: [<c02f81e3>] unlock_kernel+0xd/0x24 SS:ESP 0068:f65b1e68 [ 53.374302] ---[ end trace 05965e9e089c46c7 ]---With my best regards, Dmitry.
Signature · 1 line
Hans Verkuil - video4linux developer - sponsored by TANDBERG
HIi Hans
Quoted 4 lines
Hi Dmitri,
Just a quick note: the video4linux mailinglist is obsolete, just use linux-media.
OK
Quoted 54 lines · On Wednesday 27 January 2010 06:36:37 Dmitri Belimov wrote:
Quoted 8 lines
Hi Hans.
I finished saa7134 part of SPI. Please review
saa7134-spi.cand diff saa7134-core and etc. I wrote config of SPI to board structure. Use this config for register master and slave devices.SPI other then I2C, do not need call
request_module. Udev do it. I spend 10 days for understanding :(I'm almost certain that spi works the same way as i2c and that means that you must call
request_module. Yes, udev will load it for you, but that is a delayed load: i.e. the module may not be loaded when we need it. The idea behind this is that usually i2c or spi modules are standalone, but in the context of v4l such modules are required to be present before the bridge can properly configure itself.The easiest way to ensure the correct load sequence is to do a
request_moduleat the start.Now, I haven't compiled this, but I think this will work:
struct
v4l2_subdev*v4l2_spi_new_subdev(structv4l2_device*v4l2_dev,
structspi_master*master, structspi_board_info*info){ struct v4l2_subdev *sd = NULL; struct spi_device *spi; BUG_ON(!v4l2_dev); if (module_name) request_module(module_name); spi = spi_new_device(master, info); if (spi == NULL || spi->dev.driver == NULL) goto error; if (!try_module_get(spi->dev.driver->owner)) goto error; sd = spi_get_drvdata(spi); /* Register with the v4l2_device which increases the module's use count as well. */ if (v4l2_device_register_subdev(v4l2_dev, sd)) sd = NULL; /* Decrease the module use count to match the first
try_module_get. */module_put(spi->dev.driver->owner);error:
/* If we have a client but no subdev, then something went
Quoted 8 lines
wrong and we must unregister the client. */
if (spi && sd == NULL) spi_unregister_device(spi); return sd; }
EXPORT_SYMBOL_GPL(v4l2_spi_new_subdev);
Not work
[ 6.048195] Linux video capture interface: v2.00 [ 6.112987] saa7130/34: v4l2 driver version 0.2.15 loaded [ 6.113067] saa7134 0000:04:01.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19 [ 6.113117] saa7133[0]: found at 0000:04:01.0, rev: 209, irq: 19, latency: 32, mmio: 0xe5100000 [ 6.113176] saa7133[0]: subsystem: 5ace:7595, board: Beholder BeholdTV X7 [card=171,autodetected] [ 6.113241] saa7133[0]: board init: gpio is 200000 [ 6.113292] IRQ 19/saa7133[0]: IRQF_DISABLED is not guaranteed on shared IRQs [ 6.264512] saa7133[0]: i2c eeprom 00: ce 5a 95 75 54 20 00 00 00 00 00 00 00 00 00 01 [ 6.265136] saa7133[0]: i2c eeprom 10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 6.265731] saa7133[0]: i2c eeprom 20: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 6.266327] saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 6.266922] saa7133[0]: i2c eeprom 40: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 6.267517] saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 6.268113] saa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 6.268718] saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 6.269313] saa7133[0]: i2c eeprom 80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 6.269908] saa7133[0]: i2c eeprom 90: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 6.270503] saa7133[0]: i2c eeprom a0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 6.271098] saa7133[0]: i2c eeprom b0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 6.271693] saa7133[0]: i2c eeprom c0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 6.272289] saa7133[0]: i2c eeprom d0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 6.272895] saa7133[0]: i2c eeprom e0: 00 00 00 00 ff ff ff ff ff ff ff ff ff ff ff ff [ 6.273490] saa7133[0]: i2c eeprom f0: 42 54 56 30 30 30 30 ff ff ff ff ff ff ff ff ff [ 6.360023] tuner 1-0061: chip found @ 0xc2 (saa7133[0]) [ 6.401952] xc5000 1-0061: creating new instance [ 6.412005] xc5000: Successfully identified at address 0x61 [ 6.412054] xc5000: Firmware has not been loaded previously [ 6.477742] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 6.477816] HDA Intel 0000:00:1b.0: setting latency timer to 64
[ 34.752763] saa7134 0000:04:01.0: spi master registered: bus_num=32766 num_chipselect=1 [ 34.752823] saa7133[0]: found muPD61151 MPEG encoder [ 34.752883] befor request_module
[ 240.476013] INFO: task modprobe:1404 blocked for more than 120 seconds. [ 240.476016] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 240.476018] modprobe D f6b913c0 0 1404 1 [ 240.476021] c200f0c0 00000086 00989680 f6b913c0 c011b1fd c043f0c0 00000003 00000000 [ 240.476027] f711faa0 f711fc54 00000000 0001ecac 176f9ddf 00000008 f711facc f711faa0 [ 240.476031] f7070490 c011cc8e 00000000 c200f0c0 c02ff658 00000001 f7070490 00000046 [ 240.476036] Call Trace: [ 240.476042] [<c011b1fd>] ? wakeup_preempt_entity+0xf0/0x110 [ 240.476046] [<c011cc8e>] ? check_preempt_wakeup+0x139/0x173 [ 240.476050] [<c02f6984>] ? schedule+0x5/0x13 [ 240.476052] [<c02f6ab0>] ? schedule_timeout+0x15/0x16a [ 240.476055] [<c011bba4>] ? __wake_up_common+0x34/0x59 [ 240.476057] [<c011c477>] ? __wake_up+0x29/0x39 [ 240.476060] [<c02f6069>] ? wait_for_common+0xba/0x115 [ 240.476063] [<c0122170>] ? default_wake_function+0x0/0x8 [ 240.476067] [<c0133e10>] ? call_usermodehelper_exec+0x6e/0xae [ 240.476069] [<c0133fd5>] ? __request_module+0xdb/0xee [ 240.476076] [<f847c647>] ? spi_bitbang_setup+0xe7/0xfb [spi_bitbang] [ 240.476082] [<f84c8f3b>] ? v4l2_spi_new_subdev_board+0x2e/0x35 [v4l2_common] [ 240.476086] [<f84c8fa6>] ? v4l2_spi_new_subdev+0x64/0x6c [v4l2_common] [ 240.476099] [<f852c0b5>] ? saa7134_initdev+0x6dd/0xa96 [saa7134] [ 240.476103] [<c0213045>] ? local_pci_probe+0xb/0xc [ 240.476105] [<c02139bd>] ? pci_device_probe+0x41/0x63 [ 240.476109] [<c026d03c>] ? driver_probe_device+0x76/0xfe [ 240.476112] [<c026d104>] ? __driver_attach+0x40/0x5b [ 240.476115] [<c026cad8>] ? bus_for_each_dev+0x37/0x5f [ 240.476117] [<c026cf23>] ? driver_attach+0x11/0x13 [ 240.476120] [<c026d0c4>] ? __driver_attach+0x0/0x5b [ 240.476122] [<c026c56a>] ? bus_add_driver+0xcb/0x1ee [ 240.476131] [<f854b000>] ? saa7134_init+0x0/0x3b [saa7134] [ 240.476134] [<c026d31f>] ? driver_register+0x87/0xe0 [ 240.476143] [<f854b000>] ? saa7134_init+0x0/0x3b [saa7134] [ 240.476146] [<c0213cf5>] ? __pci_register_driver+0x33/0x8a [ 240.476154] [<f854b000>] ? saa7134_init+0x0/0x3b [saa7134] [ 240.476157] [<c010112d>] ? do_one_initcall+0x44/0x111 [ 240.476160] [<c016107f>] ? tracepoint_module_notify+0x21/0x24 [ 240.476164] [<c013a5b6>] ? notifier_call_chain+0x2a/0x47 [ 240.476167] [<c013a80b>] ? __blocking_notifier_call_chain+0x3f/0x49 [ 240.476171] [<c0147a67>] ? sys_init_module+0x87/0x187 [ 240.476173] [<c0102f74>] ? sysenter_do_call+0x12/0x28 [ 240.476177] INFO: task modprobe:1705 blocked for more than 120 seconds. [ 240.476178] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 240.476180] modprobe D f6a54040 0 1705 1704 [ 240.476182] c200f0c0 00000082 c0202b29 f6a54040 c04b8eb0 c043f0c0 c019c7f4 00000001 [ 240.476187] f7188450 f7188604 00000000 c04b8ea0 1894fb69 00000008 00000001 f7020774 [ 240.476192] c0202998 f68e7e68 c04b8ea0 00000006 00000001 00000000 ffffffc1 00000001 [ 240.476196] Call Trace: [ 240.476199] [<c0202b29>] ? ida_get_new_above+0xd4/0x178 [ 240.476203] [<c019c7f4>] ? find_inode+0x1b/0x56 [ 240.476205] [<c0202998>] ? idr_get_empty_slot+0x145/0x202 [ 240.476208] [<c0202b29>] ? ida_get_new_above+0xd4/0x178 [ 240.476211] [<c02f6984>] ? schedule+0x5/0x13 [ 240.476213] [<c02f6ab0>] ? schedule_timeout+0x15/0x16a [ 240.476216] [<c019c44c>] ? iput+0x21/0x4a [ 240.476219] [<c01cad13>] ? sysfs_addrm_finish+0x46/0x1a6 [ 240.476221] [<c01caa40>] ? sysfs_add_one+0x10/0xad [ 240.476224] [<c02f761e>] ? __down+0x4e/0x73 [ 240.476227] [<c013a54c>] ? down+0x1f/0x2a [ 240.476229] [<c026d0eb>] ? __driver_attach+0x27/0x5b [ 240.476232] [<c026cad8>] ? bus_for_each_dev+0x37/0x5f [ 240.476234] [<c026cf23>] ? driver_attach+0x11/0x13 [ 240.476237] [<c026d0c4>] ? __driver_attach+0x0/0x5b [ 240.476239] [<c026c56a>] ? bus_add_driver+0xcb/0x1ee [ 240.476243] [<f874f000>] ? init_upd61151+0x0/0xa [upd61151] [ 240.476245] [<c026d31f>] ? driver_register+0x87/0xe0 [ 240.476248] [<f874f000>] ? init_upd61151+0x0/0xa [upd61151] [ 240.476250] [<c010112d>] ? do_one_initcall+0x44/0x111 [ 240.476253] [<c016107f>] ? tracepoint_module_notify+0x21/0x24 [ 240.476256] [<c013a5b6>] ? notifier_call_chain+0x2a/0x47 [ 240.476259] [<c013a80b>] ? __blocking_notifier_call_chain+0x3f/0x49 [ 240.476261] [<c0147a67>] ? sys_init_module+0x87/0x187 [ 240.476264] [<c0102f74>] ? sysenter_do_call+0x12/0x28 [ 240.476267] [<c013007b>] ? prepare_signal+0x10f/0x184 [ 240.476269] [<c0130000>] ? prepare_signal+0x94/0x184
Module not load successfull. As I see spi_register_driver in upd61151.c not finished a long long long time and killed by kernel. I see this message last 10 days befor removing request_module from function.
Quoted 2 lines
Note that you mixed up the spi master and spi client in your original code. So it is no wonder you experienced crashes.
Yes, this is my error you are right. :((
struct spi_device *spi;
spi = spi_new_device(master, info);
Quoted 2 lines
And in
v4l2_spi_subdev_init()you should usespi_set_drvdatainstead ofdev_set_drvdata.
Ok
Quoted 1 line
I hope this helps.
Thank you.
Quoted 137 lines
Regards,
Hans
Quoted 130 lines
I need help with
v4l2-common.c-> functionv4l2_spi_new_subdev_boardThe module of SPI slave loading after some time and spi device hasn'tv4l2_subdevstructure forv4l2_device_register_subdev.Now I get kernel crash when call
v4l2_device_register_subdev.Need use a callback metod or other. I don't know.
Copy to Mauro Carvalho Chehab and mailing lists for review my code too.
Dmesg log without call
v4l2_device_register_subdev.[ 4.742279] Linux video capture interface: v2.00 [ 4.816171] saa7130/34: v4l2 driver version 0.2.15 loaded [ 4.816253] saa7134 0000:04:01.0: PCI INT A -> GSI 19 (level,low) -> IRQ 19 [ 4.816304] saa7133[0]: found at 0000:04:01.0,
rev: 209, irq: 19, latency: 32, mmio:0xe5100000[ 4.816363]
saa7133[0]: subsystem: 5ace:7595, board: Beholder BeholdTV X7
[card=171,autodetected] [ 4.816430] saa7133[0]: board init: gpio
is 200000 [ 4.816481] IRQ 19/saa7133[0]:IRQF_DISABLEDis not
guaranteed on shared IRQs [ 4.976010] saa7133[0]: i2c eeprom 00:
ce 5a 95 75 54 20 00 00 00 00 00 00 00 00 00 01 [ 4.976635]
saa7133[0]: i2c eeprom 10: ff ff ff ff ff ff ff ff ff ff ff ff ff
ff ff ff [ 4.977231] saa7133[0]: i2c eeprom 20: ff ff ff ff ff
ff ff ff ff ff ff ff ff ff ff ff [ 4.977827] saa7133[0]: i2c
eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff[ 4.978423] saa7133[0]: i2c eeprom 40: ff ff ff ff ff ff ff ffff ff ff ff ff ff ff ff [ 4.979019] saa7133[0]: i2c eeprom 50:
ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 4.979615]
saa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff
ff ff ff [ 4.980223] saa7133[0]: i2c eeprom 70: ff ff ff ff ff
ff ff ff ff ff ff ff ff ff ff ff [ 4.980820] saa7133[0]: i2c
eeprom 80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff[ 4.981416] saa7133[0]: i2c eeprom 90: ff ff ff ff ff ff ff ffff ff ff ff ff ff ff ff [ 4.982012] saa7133[0]: i2c eeprom a0:
ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 4.982608]
saa7133[0]: i2c eeprom b0: ff ff ff ff ff ff ff ff ff ff ff ff ff
ff ff ff [ 4.983204] saa7133[0]: i2c eeprom c0: ff ff ff ff ff
ff ff ff ff ff ff ff ff ff ff ff [ 4.983800] saa7133[0]: i2c
eeprom d0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff[ 4.984437] saa7133[0]: i2c eeprom e0: 00 00 00 00 ff ff ff ffff ff ff ff ff ff ff ff [ 4.985033] saa7133[0]: i2c eeprom f0:
42 54 56 30 30 30 30 ff ff ff ff ff ff ff ff ff [ 5.008041]
tuner 1-0061: chip found @0xc2(saa7133[0]) [ 5.024036] HDA
Intel 0000:00:1b.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16[ 5.024109] HDA Intel 0000:00:1b.0: setting latency timer to 64 [ 5.066725] xc5000 1-0061: creating new instance [ 5.076009]xc5000: Successfully identified at address
0x61[ 5.076060]
xc5000: Firmware has not been loaded previously[ 33.381216] saa7134 0000:04:01.0: spi master registered: bus_num=32766 num_chipselect=1 [ 33.381274] saa7133[0]: found muPD61151 MPEG encoder [ 33.381430] saa7133[0]: registered device video0 [v4l2] [ 33.381491] saa7133[0]: registered device vbi0 [ 33.381551] saa7133[0]: registered device radio0 [ 33.406256] saa7133[0]: registered device video1 [mpeg] [ 33.407628] upd61151_probe function [ 33.407672] Read test REG 0xD8 : [ 33.409502] REG = 0x0 [ 33.409547] Write test 0x03 to REG 0xD8 : [ 33.411353] Next read test REG 0xD8 : [ 33.413176] REG = 0x3 [ 33.431308] saa7134 ALSA driver for DMA sound loaded [ 33.431363] IRQ 19/saa7133[0]: IRQF_DISABLED is not guaranteedon shared IRQs [ 33.431425] saa7133[0]/alsa: saa7133[0] at
0xe5100000irq 19 registered as card -1[ 48.657067] xc5000: I2C write failed (len=4) [ 48.760018] xc5000: I2C write failed (len=4) [ 48.762960] xc5000: I2C read failed [ 48.763011] xc5000: I2C read failed [ 48.763054] xc5000: waiting for firmware upload(dvb-fe-xc5000-1.6.114.fw)... [ 48.763102] saa7134 0000:04:01.0:
firmware: requesting dvb-fe-xc5000-1.6.114.fw [ 48.802473]
xc5000: firmware read 12401 bytes. [ 48.802477] xc5000: firmware
uploading... [ 49.328504] eth0: no IPv6 routers present[ 52.132007] xc5000: firmware upload complete... [ 53.366772] ------------[ cut here ]------------ [ 53.366820] kernel BUG at lib/kernel_lock.c:126! [ 53.366865] invalid opcode: 0000 [#1] SMP [ 53.366973] last sysfs file: /sys/class/firmware/0000:04:01.0/loading [ 53.367019] Modules linked in: ipv6 dm_snapshot dm_mirror dm_region_hash dm_log
dm_modloopsaa7134_alsaupd61151saa7134_empressir_kbd_i2csnd_hda_codec_realtekxc5000snd_hda_intelsnd_hda_codectunersnd_pcm_osssnd_mixer_osssnd_pcmsnd_seq_dummysnd_seq_osssnd_seq_midisnd_rawmidisnd_seq_midi_eventsnd_seqsaa7134snd_timerir_commonv4l2_commonvideodevsnd_seq_devicev4l1_compatvideobuf_dma_sgvideobuf_corespi_bitbangpsmouse sndir_coreserio_rawtveeprom soundcoreparport_pcparport processori2c_i801buttonsnd_page_alloci2c_coreintel_agpagpgartrng_corepcspkr evdev ext3 jbd mbcache sgsr_modcdromsd_modata_genericata_piixlibatascsi_modide_pci_genericide_coreehci_hcduhci_hcdr8169 mii usbcore thermal fanthermal_sys[last unloaded:scsi_wait_scan][ 53.369624] [ 53.369666] Pid: 2659, comm: hald-probe-vide Not tainted (2.6.30.5 #1) G31M-ES2L [ 53.369721] EIP: 0060:[<c02f81e3>] EFLAGS: 00010286 CPU: 0 [ 53.369770] EIP is at unlock_kernel+0xd/0x24 [ 53.369814] EAX: f6bc26ac EBX: f6bc2000 ECX: f6bc26ac EDX: f707e4d0 [ 53.369860] ESI: 00000000 EDI: f6aa90c0 EBP: f6bc26ac ESP: f65b1e68 [ 53.369906] DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068 [ 53.369952] Process hald-probe-vide (pid: 2659, ti=f65b0000 task=f707e4d0 task.ti=f65b0000) [ 53.370008] Stack: [ 53.370049] f873e9c9 00000000 f687c804 f6aa90c0 00000000 f848e309 00000000 f6b4d680 [ 53.370298] f6b4d680 c0190049 f6aa90c0 f6a144e4 00000000 f6aa90c0 00000000 f6a144e4 [ 53.370298] c018ff24 c018c3b9 f701ef40 f6d11a5c f6aa90c0 f65b1f0c f65b1f0c 00008001 [ 53.370298] Call Trace: [ 53.370298] [<f873e9c9>] ? ts_open+0x8c/0x93 [saa7134_empress] [ 53.370298] [<f848e309>] ? v4l2_open+0x65/0x78 [videodev] [ 53.370298] [<c0190049>] ? chrdev_open+0x125/0x13c [ 53.370298] [<c018ff24>] ? chrdev_open+0x0/0x13c [ 53.370298] [<c018c3b9>] ? __dentry_open+0x119/0x208 [ 53.370298] [<c018c539>] ? nameidata_to_filp+0x29/0x3c [ 53.370298] [<c0197338>] ? do_filp_open+0x41e/0x7bc [ 53.370298] [<c017bb3c>] ? handle_mm_fault+0x294/0x5fd [ 53.370298] [<c019e267>] ? alloc_fd+0x52/0xb8 [ 53.370298] [<c018c1d1>] ? do_sys_open+0x44/0xb4 [ 53.370298] [<c018c285>] ? sys_open+0x1e/0x23 [ 53.370298] [<c0102f74>] ? sysenter_do_call+0x12/0x28 [ 53.370298] Code: 0f c1 05 e0 4b 3ec0 38 e0 74 09 f3 90 a0 e0 4b 3e c0 eb f3 64 a1 00 b0 43 c0 89 50 14 c3 64 8b 15 00 b0 43 c0 83 7a 14 00 79 04 <0f> 0b eb fe 8b 42 14
48 85 c0 89 42 14 79 07 f0 fe 05 e0 4b 3e [ 53.370298] EIP:
[<c02f81e3>]unlock_kernel+0xd/0x24SS:ESP 0068:f65b1e68[ 53.374302] ---[ end trace 05965e9e089c46c7 ]---With my best regards, Dmitry.
Signature · 1 line
Hans Verkuil - video4linux developer - sponsored by TANDBERG
Re: saa7134 and μPD61151 MPEG2 coder
Quoted 41 lines · On Thursday 28 January 2010 03:09:41 Dmitri Belimov wrote:
HIi Hans
Quoted 4 lines
Hi Dmitri,
Just a quick note: the video4linux mailinglist is obsolete, just use linux-media.
OK
Quoted 32 lines · On Wednesday 27 January 2010 06:36:37 Dmitri Belimov wrote:
Quoted 8 lines
Hi Hans.
I finished saa7134 part of SPI. Please review
saa7134-spi.cand diff saa7134-core and etc. I wrote config of SPI to board structure. Use this config for register master and slave devices.SPI other then I2C, do not need call
request_module. Udev do it. I spend 10 days for understanding :(I'm almost certain that spi works the same way as i2c and that means that you must call
request_module. Yes, udev will load it for you, but that is a delayed load: i.e. the module may not be loaded when we need it. The idea behind this is that usually i2c or spi modules are standalone, but in the context of v4l such modules are required to be present before the bridge can properly configure itself.The easiest way to ensure the correct load sequence is to do a
request_moduleat the start.Now, I haven't compiled this, but I think this will work:
struct
v4l2_subdev*v4l2_spi_new_subdev(structv4l2_device*v4l2_dev,
structspi_master*master, structspi_board_info*info){ struct v4l2_subdev *sd = NULL; struct spi_device *spi; BUG_ON(!v4l2_dev); if (module_name) request_module(module_name);
There is one thing missing here: module_name should be passed in as argument to v4l2_spi_new_subdev. Does this code actually compile? If so, then I suspect module_name must be some global variable with some bogus value which causes request_module to time out.
Quoted 2 lines
[ 240.476082] [<f84c8f3b>] ? v4l2_spi_new_subdev_board+0x2e/0x35 [v4l2_common] [ 240.476086] [<f84c8fa6>] ? v4l2_spi_new_subdev+0x64/0x6c [v4l2_common]
Remove v4l2_spi_new_subdev_board. Just have a v4l2_spi_new_subdev as in my code.
Regards,
Hans
Signature · 1 line
Hans Verkuil - video4linux developer - sponsored by TANDBERG
Hi Hans
Quoted 40 lines
Quoted 30 lines
Quoted 30 lines · On Wednesday 27 January 2010 06:36:37 Dmitri Belimov wrote:
Quoted 9 lines
Hi Hans.
I finished saa7134 part of SPI. Please review
saa7134-spi.cand diff saa7134-core and etc. I wrote config of SPI to board structure. Use this config for register master and slave devices.SPI other then I2C, do not need call
request_module. Udev do it. I spend 10 days for understanding :(I'm almost certain that spi works the same way as i2c and that means that you must call
request_module. Yes, udev will load it for you, but that is a delayed load: i.e. the module may not be loaded when we need it. The idea behind this is that usually i2c or spi modules are standalone, but in the context of v4l such modules are required to be present before the bridge can properly configure itself.The easiest way to ensure the correct load sequence is to do a
request_moduleat the start.Now, I haven't compiled this, but I think this will work:
struct
v4l2_subdev*v4l2_spi_new_subdev(structv4l2_device*v4l2_dev, structspi_master*master, structspi_board_info*info){ struct v4l2_subdev *sd = NULL; struct spi_device *spi;Quoted 4 lines
Quoted 4 lines
BUG_ON(!v4l2_dev); if (module_name) request_module(module_name);There is one thing missing here:
module_nameshould be passed in as argument tov4l2_spi_new_subdev. Does this code actually compile? If so, then I suspectmodule_namemust be some global variable with some bogus value which causesrequest_moduleto time out.
Quoted 6 lines
Quoted 3 lines
[ 240.476082] [<f84c8f3b>] ? v4l2_spi_new_subdev_board+0x2e/0x35[
v4l2_common] [ 240.476086] [<f84c8fa6>] ?v4l2_spi_new_subdev+0x64/0x6c[v4l2_common]Remove
v4l2_spi_new_subdev_board. Just have av4l2_spi_new_subdevas in my code.
I found my error. Calling request_module befor spi_new_device is good.
As I see new v4l2_subdev ops hooked and calling
[ 52.796008] DEBUG uPD61151: upd61151_s_std
My next task move our MPEG2 code to upd61151.c
Please review my changes for v4l2_spi_new_subdev.
[ 4.743008] Linux video capture interface: v2.00 [ 4.788866] saa7130/34: v4l2 driver version 0.2.15 loaded [ 4.788946] saa7134 0000:04:01.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19 [ 4.788996] saa7133[0]: found at 0000:04:01.0, rev: 209, irq: 19, latency: 32, mmio: 0xe5100000 [ 4.789055] saa7133[0]: subsystem: 5ace:7595, board: Beholder BeholdTV X7 [card=171,autodetected] [ 4.789122] saa7133[0]: board init: gpio is 200000 [ 4.789172] IRQ 19/saa7133[0]: IRQF_DISABLED is not guaranteed on shared IRQs [ 4.868459] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 4.868533] HDA Intel 0000:00:1b.0: setting latency timer to 64 [ 4.952004] saa7133[0]: i2c eeprom 00: ce 5a 95 75 54 20 00 00 00 00 00 00 00 00 00 01 [ 4.952604] saa7133[0]: i2c eeprom 10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 4.953202] saa7133[0]: i2c eeprom 20: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 4.953799] saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 4.954397] saa7133[0]: i2c eeprom 40: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 4.954994] saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 4.955592] saa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 4.956200] saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 4.956798] saa7133[0]: i2c eeprom 80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 4.957395] saa7133[0]: i2c eeprom 90: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 4.957993] saa7133[0]: i2c eeprom a0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 4.958591] saa7133[0]: i2c eeprom b0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 4.959189] saa7133[0]: i2c eeprom c0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 4.959786] saa7133[0]: i2c eeprom d0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 4.960394] saa7133[0]: i2c eeprom e0: 00 00 00 00 ff ff ff ff ff ff ff ff ff ff ff ff [ 4.960991] saa7133[0]: i2c eeprom f0: 42 54 56 30 30 30 30 ff ff ff ff ff ff ff ff ff [ 5.012044] tuner 1-0061: chip found @ 0xc2 (saa7133[0]) [ 5.128672] xc5000 1-0061: creating new instance [ 5.136014] xc5000: Successfully identified at address 0x61 [ 5.136067] xc5000: Firmware has not been loaded previously
[ 33.425823] saa7134 0000:04:01.0: spi master registered: bus_num=32766 num_chipselect=1 [ 33.425883] saa7133[0]: found muPD61151 MPEG encoder [ 33.425928] befor request_module upd61151 [ 33.435609] upd61151_probe function [ 33.435654] Read test REG 0xD8 : [ 33.437463] REG = 0x0 [ 33.437505] Write test 0x03 to REG 0xD8 : [ 33.439310] Next read test REG 0xD8 : [ 33.441123] REG = 0x3 [ 33.441167] befor spi_get_drvdata [ 33.441210] subdev pointer = f646e7c0 [ 33.441253] befor register_subdev [ 33.441297] DEBIG SPI: [ 33.441298] spi pointer = f7087580 [ 33.441298] spi->dev.driver = f873dd70 [ 33.441299] sd pointer = f646e7c0 [ 33.441579] saa7133[0]: registered device video0 [v4l2] [ 33.441640] saa7133[0]: registered device vbi0 [ 33.441700] saa7133[0]: registered device radio0 [ 33.459770] saa7133[0]: registered device video1 [mpeg] [ 33.486244] saa7134 ALSA driver for DMA sound loaded [ 33.486301] IRQ 19/saa7133[0]: IRQF_DISABLED is not guaranteed on shared IRQs [ 33.486364] saa7133[0]/alsa: saa7133[0] at 0xe5100000 irq 19 registered as card -1
[ 48.557569] xc5000: I2C write failed (len=4) [ 48.660019] xc5000: I2C write failed (len=4) [ 48.662966] xc5000: I2C read failed [ 48.663016] xc5000: I2C read failed [ 48.663060] xc5000: waiting for firmware upload (dvb-fe-xc5000-1.6.114.fw)... [ 48.663108] saa7134 0000:04:01.0: firmware: requesting dvb-fe-xc5000-1.6.114.fw [ 48.705533] xc5000: firmware read 12401 bytes. [ 48.705535] xc5000: firmware uploading...
[ 52.044007] xc5000: firmware upload complete... [ 52.796008] DEBUG uPD61151: upd61151_s_std [ 52.796058] DEBUG uPD61151: upd61151_s_std [ 53.268008] DEBUG uPD61151: upd61151_s_std [ 53.268060] DEBUG uPD61151: upd61151_s_std [ 53.270837] ------------[ cut here ]------------ [ 53.270884] kernel BUG at lib/kernel_lock.c:126! [ 53.270929] invalid opcode: 0000 [#1] SMP [ 53.271037] last sysfs file: /sys/class/firmware/0000:04:01.0/loading [ 53.271084] Modules linked in: ipv6 dm_snapshot dm_mirror dm_region_hash dm_log dm_mod loop saa7134_alsa saa7134_empress upd61151 ir_kbd_i2c xc5000 tuner snd_hda_codec_realtek snd_hda_intel snd_hda_codec snd_pcm_oss snd_mixer_oss snd_pcm snd_seq_dummy saa7134 ir_common v4l2_common videodev snd_seq_oss v4l1_compat videobuf_dma_sg videobuf_core spi_bitbang snd_seq_midi ir_core snd_rawmidi tveeprom psmouse snd_seq_midi_event serio_raw snd_seq snd_timer snd_seq_device i2c_i801 i2c_core rng_core pcspkr snd soundcore parport_pc parport snd_page_alloc button processor intel_agp agpgart evdev ext3 jbd mbcache sg sr_mod cdrom sd_mod ata_generic ata_piix libata scsi_mod ehci_hcd ide_pci_generic uhci_hcd ide_core usbcore r8169 mii thermal fan thermal_sys [last unloaded: scsi_wait_scan] [ 53.273694] [ 53.273737] Pid: 2675, comm: hald-probe-vide Not tainted (2.6.30.5 #1) G31M-ES2L [ 53.273793] EIP: 0060:[<c02f81e3>] EFLAGS: 00010286 CPU: 0 [ 53.273841] EIP is at unlock_kernel+0xd/0x24 [ 53.273885] EAX: f6b7f6ac EBX: f6b7f000 ECX: f6b7f6ac EDX: f7168b20 [ 53.273932] ESI: 00000000 EDI: f6860640 EBP: f6b7f6ac ESP: f66c9e68 [ 53.273978] DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068 [ 53.274024] Process hald-probe-vide (pid: 2675, ti=f66c8000 task=f7168b20 task.ti=f66c8000) [ 53.274079] Stack: [ 53.274121] f87499c9 00000000 f69c9804 f6860640 00000000 f8504309 00000000 f6940e00 [ 53.274360] f6940e00 c0190049 f6860640 f6aec86c 00000000 f6860640 00000000 f6aec86c [ 53.274360] c018ff24 c018c3b9 f701e1c0 f6d148d0 f6860640 f66c9f0c f66c9f0c 00008001 [ 53.274360] Call Trace: [ 53.274360] [<f87499c9>] ? ts_open+0x8c/0x93 [saa7134_empress] [ 53.274360] [<f8504309>] ? v4l2_open+0x65/0x78 [videodev] [ 53.274360] [<c0190049>] ? chrdev_open+0x125/0x13c [ 53.274360] [<c018ff24>] ? chrdev_open+0x0/0x13c [ 53.274360] [<c018c3b9>] ? __dentry_open+0x119/0x208 [ 53.274360] [<c018c539>] ? nameidata_to_filp+0x29/0x3c [ 53.274360] [<c0197338>] ? do_filp_open+0x41e/0x7bc [ 53.274360] [<c017bb3c>] ? handle_mm_fault+0x294/0x5fd [ 53.274360] [<c019e267>] ? alloc_fd+0x52/0xb8 [ 53.274360] [<c018c1d1>] ? do_sys_open+0x44/0xb4 [ 53.274360] [<c018c285>] ? sys_open+0x1e/0x23 [ 53.274360] [<c0102f74>] ? sysenter_do_call+0x12/0x28 [ 53.274360] Code: 0f c1 05 e0 4b 3e c0 38 e0 74 09 f3 90 a0 e0 4b 3e c0 eb f3 64 a1 00 b0 43 c0 89 50 14 c3 64 8b 15 00 b0 43 c0 83 7a 14 00 79 04 <0f> 0b eb fe 8b 42 14 48 85 c0 89 42 14 79 07 f0 fe 05 e0 4b 3e [ 53.274360] EIP: [<c02f81e3>] unlock_kernel+0xd/0x24 SS:ESP 0068:f66c9e68 [ 53.278380] ---[ end trace 717d799b0d534ca3 ]---
With my best regards, Dmitry.
Quoted 6 lines
Regards,
Hans
Signature · 1 line
Hans Verkuil - video4linux developer - sponsored by TANDBERG
linux/drivers/media/video/saa7134/Makefile +2 -2
@@ -1,9 +1,9 @@ saa7134-objs := saa7134-cards.o saa7134-core.o saa7134-i2c.o \ saa7134-ts.o saa7134-tvaudio.o saa7134-vbi.o \ - saa7134-video.o saa7134-input.o + saa7134-video.o saa7134-input.o saa7134-spi.o -obj-$(CONFIG_VIDEO_SAA7134) += saa6752hs.o saa7134.o saa7134-empress.o +obj-$(CONFIG_VIDEO_SAA7134) += saa6752hs.o saa7134.o saa7134-empress.o upd61151.o obj-$(CONFIG_VIDEO_SAA7134_ALSA) += saa7134-alsa.o
linux/drivers/media/video/saa7134/saa7134-cards.c +39 -8
80 lines not on this page · raw message
linux/drivers/media/video/saa7134/saa7134-core.c +48 -3
78 lines not on this page · raw message
linux/drivers/media/video/saa7134/saa7134.h +44 -0
98 lines not on this page · raw message
linux/drivers/media/video/v4l2-common.c +70 -0
82 lines not on this page · raw message
linux/include/media/v4l2-common.h +19 -0
@@ -191,6 +191,25 @@/* ------------------------------------------------------------------------- */ +/* SPI Helper functions */ + +#include <linux/spi/spi.h> + +struct spi_device_id ; +struct spi_device ; + +/* Load an spi module and return an initialized v4l2_subdev struct. +Only call request_module if module_name != NULL. +The client_type argument is the name of the chip that's on the adapter. */ +struct v4l2_subdev *v4l2_spi_new_subdev (struct v4l2_device *v4l2_dev, +struct spi_master *master,struct spi_board_info *info); + +/* Initialize an v4l2_subdev with data from an spi_device struct */ +void v4l2_spi_subdev_init (struct v4l2_subdev *sd,struct spi_device *spi, +const struct v4l2_subdev_ops *ops); + +/* ------------------------------------------------------------------------- */ +/* Note: these remaining ioctls/structs should be removed as well, but they are still used in tuner-simple.c (TUNER_SET_CONFIG), cx18/ivtv (RESET) and v4l2-int-device.h (v4l2_routing). To remove these ioctls some more cleanup
linux/include/media/v4l2-subdev.h +2 -0
@@ -387,6 +387,8 @@/* Set this flag if this subdev is a i2c device. */ #define V4L2_SUBDEV_FL_IS_I2C (1U << 0) +/* Set this flag if this subdev is a spi device. */ +#define V4L2_SUBDEV_FL_IS_SPI (1U << 1)/* Each instance of a subdev driver should create this struct, either stand-alone or embedded in a larger struct.
[ 4.743008] Linux video capture interface: v2.00 [ 4.788866] saa7130/34: v4l2 driver version 0.2.15 loaded [ 4.788946] saa7134 0000:04:01.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19 [ 4.788996] saa7133[0]: found at 0000:04:01.0, rev: 209, irq: 19, latency: 32, mmio: 0xe5100000 [ 4.789055] saa7133[0]: subsystem: 5ace:7595, board: Beholder BeholdTV X7 [card=171,autodetected] [ 4.789122] saa7133[0]: board init: gpio is 200000 [ 4.789172] IRQ 19/saa7133[0]: IRQF_DISABLED is not guaranteed on shared IRQs [ 4.868459] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 4.868533] HDA Intel 0000:00:1b.0: setting latency timer to 64 [ 4.952004] saa7133[0]: i2c eeprom 00: ce 5a 95 75 54 20 00 00 00 00 00 00 00 00 00 01 [ 4.952604] saa7133[0]: i2c eeprom 10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 4.953202] saa7133[0]: i2c eeprom 20: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 4.953799] saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 4.954397] saa7133[0]: i2c eeprom 40: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 4.954994] saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 4.955592] saa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 4.956200] saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 4.956798] saa7133[0]: i2c eeprom 80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 4.957395] saa7133[0]: i2c eeprom 90: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 4.957993] saa7133[0]: i2c eeprom a0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 4.958591] saa7133[0]: i2c eeprom b0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 4.959189] saa7133[0]: i2c eeprom c0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 4.959786] saa7133[0]: i2c eeprom d0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 4.960394] saa7133[0]: i2c eeprom e0: 00 00 00 00 ff ff ff ff ff ff ff ff ff ff ff ff [ 4.960991] saa7133[0]: i2c eeprom f0: 42 54 56 30 30 30 30 ff ff ff ff ff ff ff ff ff [ 5.012044] tuner 1-0061: chip found @ 0xc2 (saa7133[0]) [ 5.128672] xc5000 1-0061: creating new instance [ 5.136014] xc5000: Successfully identified at address 0x61 [ 5.136067] xc5000: Firmware has not been loaded previously
[ 33.425823] saa7134 0000:04:01.0: spi master registered: bus_num=32766 num_chipselect=1 [ 33.425883] saa7133[0]: found muPD61151 MPEG encoder [ 33.425928] befor request_module upd61151 [ 33.435609] upd61151_probe function [ 33.435654] Read test REG 0xD8 : [ 33.437463] REG = 0x0 [ 33.437505] Write test 0x03 to REG 0xD8 : [ 33.439310] Next read test REG 0xD8 : [ 33.441123] REG = 0x3 [ 33.441167] befor spi_get_drvdata [ 33.441210] subdev pointer = f646e7c0 [ 33.441253] befor register_subdev [ 33.441297] DEBIG SPI: [ 33.441298] spi pointer = f7087580 [ 33.441298] spi->dev.driver = f873dd70 [ 33.441299] sd pointer = f646e7c0 [ 33.441579] saa7133[0]: registered device video0 [v4l2] [ 33.441640] saa7133[0]: registered device vbi0 [ 33.441700] saa7133[0]: registered device radio0 [ 33.459770] saa7133[0]: registered device video1 [mpeg] [ 33.486244] saa7134 ALSA driver for DMA sound loaded [ 33.486301] IRQ 19/saa7133[0]: IRQF_DISABLED is not guaranteed on shared IRQs [ 33.486364] saa7133[0]/alsa: saa7133[0] at 0xe5100000 irq 19 registered as card -1
[ 48.557569] xc5000: I2C write failed (len=4) [ 48.660019] xc5000: I2C write failed (len=4) [ 48.662966] xc5000: I2C read failed [ 48.663016] xc5000: I2C read failed [ 48.663060] xc5000: waiting for firmware upload (dvb-fe-xc5000-1.6.114.fw)... [ 48.663108] saa7134 0000:04:01.0: firmware: requesting dvb-fe-xc5000-1.6.114.fw [ 48.705533] xc5000: firmware read 12401 bytes. [ 48.705535] xc5000: firmware uploading...
[ 52.044007] xc5000: firmware upload complete... [ 52.796008] DEBUG uPD61151: upd61151_s_std [ 52.796058] DEBUG uPD61151: upd61151_s_std [ 53.268008] DEBUG uPD61151: upd61151_s_std [ 53.268060] DEBUG uPD61151: upd61151_s_std [ 53.270837] ------------[ cut here ]------------ [ 53.270884] kernel BUG at lib/kernel_lock.c:126! [ 53.270929] invalid opcode: 0000 [#1] SMP [ 53.271037] last sysfs file: /sys/class/firmware/0000:04:01.0/loading [ 53.271084] Modules linked in: ipv6 dm_snapshot dm_mirror dm_region_hash dm_log dm_mod loop saa7134_alsa saa7134_empress upd61151 ir_kbd_i2c xc5000 tuner snd_hda_codec_realtek snd_hda_intel snd_hda_codec snd_pcm_oss snd_mixer_oss snd_pcm snd_seq_dummy saa7134 ir_common v4l2_common videodev snd_seq_oss v4l1_compat videobuf_dma_sg videobuf_core spi_bitbang snd_seq_midi ir_core snd_rawmidi tveeprom psmouse snd_seq_midi_event serio_raw snd_seq snd_timer snd_seq_device i2c_i801 i2c_core rng_core pcspkr snd soundcore parport_pc parport snd_page_alloc button processor intel_agp agpgart evdev ext3 jbd mbcache sg sr_mod cdrom sd_mod ata_generic ata_piix libata scsi_mod ehci_hcd ide_pci_generic uhci_hcd ide_core usbcore r8169 mii thermal fan thermal_sys [last unloaded: scsi_wait_scan] [ 53.273694] [ 53.273737] Pid: 2675, comm: hald-probe-vide Not tainted (2.6.30.5 #1) G31M-ES2L [ 53.273793] EIP: 0060:[<c02f81e3>] EFLAGS: 00010286 CPU: 0 [ 53.273841] EIP is at unlock_kernel+0xd/0x24 [ 53.273885] EAX: f6b7f6ac EBX: f6b7f000 ECX: f6b7f6ac EDX: f7168b20 [ 53.273932] ESI: 00000000 EDI: f6860640 EBP: f6b7f6ac ESP: f66c9e68 [ 53.273978] DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068 [ 53.274024] Process hald-probe-vide (pid: 2675, ti=f66c8000 task=f7168b20 task.ti=f66c8000) [ 53.274079] Stack: [ 53.274121] f87499c9 00000000 f69c9804 f6860640 00000000 f8504309 00000000 f6940e00 [ 53.274360] f6940e00 c0190049 f6860640 f6aec86c 00000000 f6860640 00000000 f6aec86c [ 53.274360] c018ff24 c018c3b9 f701e1c0 f6d148d0 f6860640 f66c9f0c f66c9f0c 00008001 [ 53.274360] Call Trace: [ 53.274360] [<f87499c9>] ? ts_open+0x8c/0x93 [saa7134_empress] [ 53.274360] [<f8504309>] ? v4l2_open+0x65/0x78 [videodev] [ 53.274360] [<c0190049>] ? chrdev_open+0x125/0x13c [ 53.274360] [<c018ff24>] ? chrdev_open+0x0/0x13c [ 53.274360] [<c018c3b9>] ? __dentry_open+0x119/0x208 [ 53.274360] [<c018c539>] ? nameidata_to_filp+0x29/0x3c [ 53.274360] [<c0197338>] ? do_filp_open+0x41e/0x7bc [ 53.274360] [<c017bb3c>] ? handle_mm_fault+0x294/0x5fd [ 53.274360] [<c019e267>] ? alloc_fd+0x52/0xb8 [ 53.274360] [<c018c1d1>] ? do_sys_open+0x44/0xb4 [ 53.274360] [<c018c285>] ? sys_open+0x1e/0x23 [ 53.274360] [<c0102f74>] ? sysenter_do_call+0x12/0x28 [ 53.274360] Code: 0f c1 05 e0 4b 3e c0 38 e0 74 09 f3 90 a0 e0 4b 3e c0 eb f3 64 a1 00 b0 43 c0 89 50 14 c3 64 8b 15 00 b0 43 c0 83 7a 14 00 79 04 <0f> 0b eb fe 8b 42 14 48 85 c0 89 42 14 79 07 f0 fe 05 e0 4b 3e [ 53.274360] EIP: [<c02f81e3>] unlock_kernel+0xd/0x24 SS:ESP 0068:f66c9e68 [ 53.278380] ---[ end trace 717d799b0d534ca3 ]---
/*
*
* Device driver for philips saa7134 based TV cards
* SPI software interface support
*
* (c) 2009 Beholder Intl. Ltd. Dmitry Belimov <[email protected]> *
* Important: now support ONLY SPI_MODE_0, see FIXME
*
* This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation; either version 2 of the License, or * (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*/
#include "saa7134-reg.h"
#include "saa7134.h"
#include <media/v4l2-common.h>
/* ----------------------------------------------------------- */
static unsigned int spi_debug; module_param(spi_debug, int, 0644); MODULE_PARM_DESC(spi_debug,"enable debug messages [spi]");
#define d1printk if (1 == spi_debug) printk
#define d2printk if (2 == spi_debug) printk
static inline void spidelay(unsigned d)
{
udelay(d);
}static inline struct saa7134_spi_gpio *to_sb(struct spi_device *spi)
{
return spi_master_get_devdata(spi->master);
}static inline void setsck(struct spi_device *dev, int on)
{
struct saa7134_spi_gpio *sb = to_sb(dev);
saa7134_set_gpio(sb->controller_data, sb->controller_data->spi.clock, on ? 1 : 0);
}static inline void setmosi(struct spi_device *dev, int on)
{
struct saa7134_spi_gpio *sb = to_sb(dev);
saa7134_set_gpio(sb->controller_data, sb->controller_data->spi.mosi, on ? 1 : 0);
}static inline u32 getmiso(struct spi_device *dev)
{
struct saa7134_spi_gpio *sb = to_sb(dev);
unsigned long status;
status = saa7134_get_gpio(sb->controller_data);
if ( status & (1 << sb->controller_data->spi.miso))
return 1;
else
return 0;
}#define EXPAND_BITBANG_TXRX 1
#include <linux/spi/spi_bitbang.h>
static void saa7134_spi_gpio_chipsel(struct spi_device *dev, int on)
{
struct saa7134_spi_gpio *sb = to_sb(dev);
if (on)
{
/* FIXME: set clock to zero by default, only SPI_MODE_0 compatible */
saa7134_set_gpio(sb->controller_data, sb->controller_data->spi.clock, 0);
saa7134_set_gpio(sb->controller_data, sb->controller_data->spi.cs, 0);
}
else
saa7134_set_gpio(sb->controller_data, sb->controller_data->spi.cs, 1);
}/* Our actual bitbanger routine. */
static u32 saa7134_txrx(struct spi_device *spi, unsigned nsecs, u32 word, u8 bits)
{
return bitbang_txrx_be_cpha0(spi, nsecs, 0, word, bits);
}static int saa7134_setup(struct spi_device *spi, struct spi_transfer *t)
{
return spi_bitbang_setup_transfer(spi, t);
}int saa7134_spi_register(struct saa7134_dev *dev, struct spi_board_info *info)
{
struct spi_master *master = NULL;
struct saa7134_spi_gpio *sb = NULL;
int ret = 0;
master = spi_alloc_master(&dev->pci->dev, sizeof(struct saa7134_spi_gpio));
if (master == NULL) {
dev_err(&dev->pci->dev, "failed to allocate spi master\n");
ret = -ENOMEM;
goto err;
}
sb = spi_master_get_devdata(master);
master->num_chipselect = dev->spi.num_chipselect;
master->bus_num = -1;
sb->master = spi_master_get(master);
sb->bitbang.master = sb->master;
sb->bitbang.master->bus_num = -1;
sb->bitbang.master->num_chipselect = dev->spi.num_chipselect;
sb->bitbang.chipselect = saa7134_spi_gpio_chipsel;
sb->bitbang.txrx_word[SPI_MODE_0] = saa7134_txrx;
sb->bitbang.setup_transfer = saa7134_setup;
/* set state of spi pins */
saa7134_set_gpio(dev, dev->spi.cs, 1);
/* FIXME: set clock to zero by default, only SPI_MODE_0 compatible */
saa7134_set_gpio(dev, dev->spi.clock, 0);
saa7134_set_gpio(dev, dev->spi.mosi, 1);
saa7134_set_gpio(dev, dev->spi.miso, 3);
/* start SPI bitbang master */
ret = spi_bitbang_start(&sb->bitbang);
if (ret) {
dev_err(&dev->pci->dev, "Failed to register SPI master\n");
goto err_no_bitbang;
}
dev_info(&dev->pci->dev,
"spi master registered: bus_num=%d num_chipselect=%d\n",
master->bus_num, master->num_chipselect);
sb->controller_data = dev;
info->bus_num = sb->master->bus_num;
info->controller_data = master;
dev->spi_adap = master;err_no_bitbang:
spi_master_put(master); err: return ret; }
int saa7134_spi_unregister(struct saa7134_dev *dev)
{
struct saa7134_spi_gpio *sb = spi_master_get_devdata(dev->spi_adap);
spi_bitbang_stop(&sb->bitbang);
spi_master_put(sb->master);
return 0;
}/*
* Overrides for Emacs so that we follow Linus's tabbing style.
* ---------------------------------------------------------------------------
* Local variables:
* c-basic-offset: 8
* End:
*/
/*
upd61151 - driver for the uPD61151 by NEC
Copyright (C) Beholder Intl. Ltd. Dmitry Belimov <[email protected]>
Based on the saa6752s.c driver.
Copyright (C) 2004 Andrew de Quincey
This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License vs published by the Free Software Foundation; either version 2 of the License, or (at your option) any later version.
This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details.
You should have received a copy of the GNU General Public License along with this program; if not, write to the Free Software Foundation, Inc., 675 Mvss Ave, Cambridge, MA 02139, USA.
*/
#include <linux/init.h>
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/device.h>
#include <linux/sysfs.h>
#include <linux/string.h>
#include <linux/timer.h>
#include <linux/delay.h>
#include <linux/errno.h>
#include <linux/slab.h>
#include <linux/poll.h>
#include <linux/spi/spi.h>
#include <linux/types.h>
//#include <linux/mod_devicetable.h>
#include "compat.h"
#include <linux/videodev2.h>
#include <media/v4l2-device.h>
#include <media/v4l2-common.h>
#include <media/v4l2-chip-ident.h>
#include <media/upd61151.h>
#include <linux/crc32.h>
#include "saa7134.h"
#define MPEG_VIDEO_TARGET_BITRATE_MAX 27000 #define MPEG_VIDEO_MAX_BITRATE_MAX 27000 #define MPEG_TOTAL_TARGET_BITRATE_MAX 27000
#define MPEG_PID_MAX ((1 << 14) - 1)
#define DRVNAME "upd61151"
static unsigned int spi_debug; module_param(spi_debug, int, 0644); MODULE_PARM_DESC(spi_debug,"enable debug messages [spi]");
#define d1printk if (1 == spi_debug) printk
#define d2printk if (2 == spi_debug) printk
MODULE_DESCRIPTION("device driver for uPD61151 MPEG2 encoder"); MODULE_AUTHOR("Dmitry V Belimov"); MODULE_LICENSE("GPL");
enum upd61151_videoformat {
UPD61151_VF_D1 = 0, /* standard D1 video format: 720x576 */
UPD61151_VF_2_3_D1 = 1,/* 2/3D1 video format: 480x576 */
UPD61151_VF_1_2_D1 = 2,/* 1/2D1 video format: 352x576 */
UPD61151_VF_SIF = 3, /* SIF video format: 352x288 */
UPD61151_VF_UNKNOWN,
};struct upd61151_mpeg_params {
/* transport streams */
__u16 ts_pid_pmt;
__u16 ts_pid_audio;
__u16 ts_pid_video;
__u16 ts_pid_pcr;
/* audio */
enum v4l2_mpeg_audio_encoding au_encoding;
enum v4l2_mpeg_audio_l2_bitrate au_l2_bitrate;
/* video */
enum v4l2_mpeg_video_aspect vi_aspect;
enum v4l2_mpeg_video_bitrate_mode vi_bitrate_mode;
__u32 vi_bitrate;
__u32 vi_bitrate_peak;
};static const struct v4l2_format v4l2_format_table[] =
{
[UPD61151_VF_D1] =
{ .fmt = { .pix = { .width = 720, .height = 576 }}},
[UPD61151_VF_2_3_D1] =
{ .fmt = { .pix = { .width = 480, .height = 576 }}},
[UPD61151_VF_1_2_D1] =
{ .fmt = { .pix = { .width = 352, .height = 576 }}},
[UPD61151_VF_SIF] =
{ .fmt = { .pix = { .width = 352, .height = 288 }}},
[UPD61151_VF_UNKNOWN] =
{ .fmt = { .pix = { .width = 0, .height = 0}}},
};struct upd61151_state {
struct v4l2_subdev sd;
int chip;
u32 revision;
struct upd61151_mpeg_params params;
enum upd61151_videoformat video_format;
v4l2_std_id standard;
};enum upd61151_command {
UPD61151_COMMAND_RESET = 0,
UPD61151_COMMAND_STOP = 1,
UPD61151_COMMAND_START = 2,
UPD61151_COMMAND_PAUSE = 3,
UPD61151_COMMAND_RECONFIGURE = 4,
UPD61151_COMMAND_SLEEP = 5,
UPD61151_COMMAND_RECONFIGURE_FORCE = 6,
UPD61151_COMMAND_MAX
};static int write_reg(struct spi_device *spi, u8 address, u8 data)
{
u8 buf[2];
buf[0] = ((address >> 2) << 2);
buf[1] = data;
d2printk(KERN_DEBUG "%s: spi data 0x%x <= 0x%x\n",spi->modalias,address,data);
return spi_write(spi, buf, ARRAY_SIZE(buf));
}static int read_reg(struct spi_device *spi, unsigned char address, unsigned char *data)
{
u8 txbuf[1];
int ret;
ret = 0;
txbuf[0] = ((address >> 2) << 2) | 0x02;
ret = spi_write_then_read(spi, txbuf, 1, data, 1);
d2printk(KERN_DEBUG "%s: spi data 0x%x => 0x%x, status %d\n",spi->modalias, address, *data, ret);
return ret;
}static struct upd61151_mpeg_params param_defaults =
{
.ts_pid_pmt = 16,
.ts_pid_video = 260,
.ts_pid_audio = 256,
.ts_pid_pcr = 259,
.vi_aspect = V4L2_MPEG_VIDEO_ASPECT_4x3,
.vi_bitrate = 4000,
.vi_bitrate_peak = 6000,
.vi_bitrate_mode = V4L2_MPEG_VIDEO_BITRATE_MODE_VBR,
.au_encoding = V4L2_MPEG_AUDIO_ENCODING_LAYER_2,
.au_l2_bitrate = V4L2_MPEG_AUDIO_L2_BITRATE_256K,
};#if 0
static int upd61151_chip_command(struct spi_device *spi,
enum upd61151_command command)
{
printk("DEBUG uPD61151: upd61151_chip_command\n");
return 0;
}static int upd61151_set_bitrate(struct spi_device *spi,
struct upd61151_state *h)
{
printk("DEBUG uPD61151: upd61151_set_bitrate\n");
return 0;
}#endif
static int upd61151_queryctrl(struct v4l2_subdev *sd, struct v4l2_queryctrl *qctrl) {
printk("DEBUG uPD61151: upd61151_queryctrl\n");
return 0;
}static int upd61151_querymenu(struct v4l2_subdev *sd, struct v4l2_querymenu *qmenu) {
printk("DEBUG uPD61151: upd61151_querymenu\n");
return 0;
}static int upd61151_init(struct v4l2_subdev *sd, u32 flags) {
printk("DEBUG uPD61151: upd61151_init\n");
return 0;
}static int upd61151_do_ext_ctrls(struct v4l2_subdev *sd, struct v4l2_ext_controls *ctrls, int set) {
printk("DEBUG uPD61151: upd61151_do_ext_ctrls\n");
return 0;
}static int upd61151_s_ext_ctrls(struct v4l2_subdev *sd, struct v4l2_ext_controls *ctrls) {
printk("DEBUG uPD61151: upd61151_s_ext_ctrls\n");
return upd61151_do_ext_ctrls(sd, ctrls, 1);
}static int upd61151_try_ext_ctrls(struct v4l2_subdev *sd, struct v4l2_ext_controls *ctrls) {
printk("DEBUG uPD61151: upd61151_s_ext_ctrls\n");
return upd61151_do_ext_ctrls(sd, ctrls, 0);
}static int upd61151_g_ext_ctrls(struct v4l2_subdev *sd, struct v4l2_ext_controls *ctrls) {
printk("DEBUG uPD61151: upd61151_g_ext_ctrls\n");
return 0;
}static int upd61151_g_fmt(struct v4l2_subdev *sd, struct v4l2_format *f) {
printk("DEBUG uPD61151: upd61151_g_fmt\n");
return 0;
}static int upd61151_s_fmt(struct v4l2_subdev *sd, struct v4l2_format *f) {
printk("DEBUG uPD61151: upd61151_s_fmt\n");
return 0;
}static int upd61151_s_std(struct v4l2_subdev *sd, v4l2_std_id std) {
printk("DEBUG uPD61151: upd61151_s_std\n");
return 0;
}static int upd61151_g_chip_ident(struct v4l2_subdev *sd, struct v4l2_dbg_chip_ident *chip) {
printk("DEBUG uPD61151: upd61151_g_chip_ident\n");
return 0;
}/* ----------------------------------------------------------------------- */
static const struct v4l2_subdev_core_ops upd61151_core_ops = {
.g_chip_ident = upd61151_g_chip_ident,
.init = upd61151_init,
.queryctrl = upd61151_queryctrl,
.querymenu = upd61151_querymenu,
.g_ext_ctrls = upd61151_g_ext_ctrls,
.s_ext_ctrls = upd61151_s_ext_ctrls,
.try_ext_ctrls = upd61151_try_ext_ctrls,
.s_std = upd61151_s_std,
};static const struct v4l2_subdev_video_ops upd61151_video_ops = {
.s_fmt = upd61151_s_fmt,
.g_fmt = upd61151_g_fmt,
};static const struct v4l2_subdev_ops upd61151_ops = {
.core = &upd61151_core_ops,
.video = &upd61151_video_ops,
};static int __devinit upd61151_probe(struct spi_device *spi)
{
struct upd61151_state *h = kzalloc(sizeof(*h), GFP_KERNEL);
struct v4l2_subdev *sd;
u8 rx_buf[2];printk("upd61151_probe function\n");
printk("Read test REG 0xD8 :\n");
read_reg(spi, 0xD8, &rx_buf[0]);
printk("REG = 0x%X\n",rx_buf[0]);
printk("Write test 0x03 to REG 0xD8 :\n");
write_reg(spi, 0xD8, 0x03);
printk("Next read test REG 0xD8 :\n");
read_reg(spi, 0xD8, &rx_buf[0]);
printk("REG = 0x%X\n",rx_buf[0]);
if (h == NULL) return -ENOMEM; sd = &h->sd; v4l2_spi_subdev_init(sd, spi, &upd61151_ops); spi_set_drvdata(spi, h);
/* function for detect a chip here */
// h->chip = upd61151_detect(h);
h->params = param_defaults; h->standard = 0; /* Assume 625 input lines */ return 0; }
static int __devexit upd61151_remove(struct spi_device *spi)
{
struct upd61151_state *h = spi_get_drvdata(spi);
printk("upd61151_remove function\n");
v4l2_device_unregister_subdev(&h->sd);
kfree(&h->sd);
spi_unregister_device(spi);
return 0;
}#if 0
static const struct spi_device_id upd61151_ids[] = {
{ "upd61151", 1 },
{ "upd61152", 2 },
{ },
};MODULE_DEVICE_TABLE(spi, upd61151_ids);
#endif
static struct spi_driver upd61151_driver = {
.driver = {
.name = DRVNAME,
.bus = &spi_bus_type,
.owner = THIS_MODULE,
},
// .id_table = upd61151_ids,
.probe = upd61151_probe, .remove = __devexit_p(upd61151_remove), };
static int __init init_upd61151(void)
{
return spi_register_driver(&upd61151_driver);
}module_init(init_upd61151);
static void __exit exit_upd61151(void)
{
spi_unregister_driver(&upd61151_driver);
}module_exit(exit_upd61151);
/*
* Overrides for Emacs so that we follow Linus's tabbing style.
* ---------------------------------------------------------------------------
* Local variables:
* c-basic-offset: 8
* End:
*/
/*
upd61151.h - definition for muPD61151 MPEG encoder
Copyright (C) Beholder Intl. Ltd. Dmitry Belimov <[email protected]>
This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation; either version 2 of the License, or (at your option) any later version.
This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details.
You should have received a copy of the GNU General Public License along with this program; if not, write to the Free Software Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*/
#if 0 /* ndef _UPD61151_H */
#define _UPD61151_H
#include <linux/firmware.h>
#define MUPD61151_DEFAULT_PS_FIRMWARE "D61151_PS_64_byte_7133_v22_031031.bin" #define MUPD61151_DEFAULT_PS_FIRMWARE_SIZE 97002
#define MUPD61151_DEFAULT_AUDIO_FIRMWARE "audrey_MPE_V1r51.bin" #define MUPD61151_DEFAULT_AUDIO_FIRMWARE_SIZE 40064
enum mpeg_video_bitrate_mode {
MPEG_VIDEO_BITRATE_MODE_VBR = 0, /* Variable bitrate */ MPEG_VIDEO_BITRATE_MODE_CBR = 1, /* Constant bitrate */
MPEG_VIDEO_BITRATE_MODE_MAX
};
enum mpeg_audio_bitrate {
MPEG_AUDIO_BITRATE_256 = 0, /* 256 kBit/sec */
MPEG_AUDIO_BITRATE_384 = 1, /* 384 kBit/sec */
MPEG_AUDIO_BITRATE_MAX
};enum mpeg_video_format {
MPEG_VIDEO_FORMAT_D1 = 0,
MPEG_VIDEO_FORMAT_2_3_D1 = 1,
MPEG_VIDEO_FORMAT_1_2_D1 = 2,
MPEG_VIDEO_FORMAT_SIF = 3,
MPEG_VIDEO_FORMAT_MAX
};#define MPEG_VIDEO_TARGET_BITRATE_MAX 27000
#define MPEG_VIDEO_MAX_BITRATE_MAX 27000
#define MPEG_TOTAL_BITRATE_MAX 27000
#define MPEG_PID_MAX ((1 << 14) - 1)
struct mpeg_params {
enum mpeg_video_bitrate_mode video_bitrate_mode;
unsigned int video_target_bitrate;
unsigned int video_max_bitrate; // only used for VBR
enum mpeg_audio_bitrate audio_bitrate;
unsigned int total_bitrate;
unsigned int pmt_pid;
unsigned int video_pid;
unsigned int audio_pid;
unsigned int pcr_pid;
enum mpeg_video_format video_format;
};#endif // _UPD61151_H
/*
* Local variables:
* c-basic-offset: 8
* End:
*/
Hi Hans
This is my last state for review.
After small time I'll finish process of initialize the encoder. Configure some register, upload two firmware for video and for audio. Configure the frontends.
I have the questions.
For configuring audio frontend need know samplerate of audio. saa7134 can only 32kHz
saa7131/3/5 on I2S 32кГц from SIF source and 32/44.1/48 from external i.e. RCA stereo audio input.
Hardcode 32kHz or need a function for determine mode of audio??
Other question. For configure VideoFrontend need know 50 or 60Hz Now I use videomode from h structure. I think more correct detect it on saa7134.
What you think??
Dmesg with normal and junk debug printk.
[ 4.901675] Linux video capture interface: v2.00 [ 5.046878] saa7130/34: v4l2 driver version 0.2.15 loaded [ 5.046964] saa7134 0000:04:01.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19 [ 5.047018] saa7133[0]: found at 0000:04:01.0, rev: 209, irq: 19, latency: 32, mmio: 0xe5100000 [ 5.047080] saa7133[0]: subsystem: 5ace:7595, board: Beholder BeholdTV X7 [card=171,autodetected] [ 5.047153] saa7133[0]: board init: gpio is 200000 [ 5.047205] IRQ 19/saa7133[0]: IRQF_DISABLED is not guaranteed on shared IRQs [ 5.196517] saa7133[0]: i2c eeprom 00: ce 5a<6>HDA Intel 0000:00:1b.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 5.196620] HDA Intel 0000:00:1b.0: setting latency timer to 64 [ 5.196687] 95 75 54 20 00 00 00 00 00 00 00 00 00 01 [ 5.197190] saa7133[0]: i2c eeprom 10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 5.197787] saa7133[0]: i2c eeprom 20: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 5.198385] saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 5.198982] saa7133[0]: i2c eeprom 40: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 5.199579] saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 5.200176] saa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 5.200785] saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 5.201382] saa7133[0]: i2c eeprom 80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 5.201979] saa7133[0]: i2c eeprom 90: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 5.202576] saa7133[0]: i2c eeprom a0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 5.203174] saa7133[0]: i2c eeprom b0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 5.203771] saa7133[0]: i2c eeprom c0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 5.204371] saa7133[0]: i2c eeprom d0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 5.204982] saa7133[0]: i2c eeprom e0: 00 00 00 00 ff ff ff ff ff ff ff ff ff ff ff ff [ 5.205579] saa7133[0]: i2c eeprom f0: 42 54 56 30 30 30 30 ff ff ff ff ff ff ff ff ff [ 5.228577] tuner 1-0061: chip found @ 0xc2 (saa7133[0]) [ 5.286091] xc5000 1-0061: creating new instance [ 5.292505] xc5000: Successfully identified at address 0x61 [ 5.292552] xc5000: Firmware has not been loaded previously [ 33.571875] saa7134 0000:04:01.0: spi master registered: bus_num=32766 num_chipselect=1 [ 33.571933] saa7133[0]: found muPD61151 MPEG encoder [ 33.601819] upd61151_probe function [ 33.602057] upd61151: MPEG2 core status 0 [ 33.602058] upd61151: need reload firmware [ 33.602059] Start load firmware... [ 33.602103] DEBUG: upd61151_download_firmware [ 33.603325] DEBUG: upd61151_load_base_firmware [ 33.603370] upd61151: waiting for base firmware upload (D61151_PS_7133_v22_031031.bin)... [ 33.603427] saa7134 0000:04:01.0: firmware: requesting D61151_PS_7133_v22_031031.bin [ 33.676430] upd61151: firmware read 97002 bytes. [ 33.676432] upd61151: base firmware uploading... [ 33.677071] upd61151: Transfer IRQ status 0x0 [ 33.678539] fw upload start [ 51.433446] fw upload stop [ 51.433677] upd61151: Transfer IRQ status 0x1 [ 51.434043] upd61151: base firmware upload complete... [ 51.434285] DEBUG: upd61151_load_audio_firmware [ 51.434330] upd61151: waiting for audio firmware upload (audrey_MPE_V1r51.bin)... [ 51.434386] saa7134 0000:04:01.0: firmware: requesting audrey_MPE_V1r51.bin [ 51.482980] upd61151: firmware read 40064 bytes. [ 51.482982] upd61151: audio firmware uploading... [ 51.483231] upd61151: Transfer IRQ status 0x1 [ 51.484700] fw upload start [ 51.508682] upd61151: Transfer IRQ status 0x2 [ 51.532479] upd61151: Transfer IRQ status 0x2 [ 51.556280] upd61151: Transfer IRQ status 0x2 [ 51.580081] upd61151: Transfer IRQ status 0x2 [ 51.603877] upd61151: Transfer IRQ status 0x2 [ 51.627677] upd61151: Transfer IRQ status 0x2 [ 51.651476] upd61151: Transfer IRQ status 0x2 [ 51.675275] upd61151: Transfer IRQ status 0x2 [ 51.699072] upd61151: Transfer IRQ status 0x2 [ 51.722870] upd61151: Transfer IRQ status 0x2 [ 51.746669] upd61151: Transfer IRQ status 0x2 [ 51.770467] upd61151: Transfer IRQ status 0x2 [ 51.794267] upd61151: Transfer IRQ status 0x2 [ 51.818092] upd61151: Transfer IRQ status 0x2 [ 51.841896] upd61151: Transfer IRQ status 0x2 [ 51.865691] upd61151: Transfer IRQ status 0x2 [ 51.889493] upd61151: Transfer IRQ status 0x2 [ 51.913290] upd61151: Transfer IRQ status 0x2 [ 51.937091] upd61151: Transfer IRQ status 0x2 [ 51.960889] upd61151: Transfer IRQ status 0x2 [ 51.984690] upd61151: Transfer IRQ status 0x2 [ 52.008479] upd61151: Transfer IRQ status 0x2 [ 52.032279] upd61151: Transfer IRQ status 0x2 [ 52.056076] upd61151: Transfer IRQ status 0x2 [ 52.079877] upd61151: Transfer IRQ status 0x2 [ 52.103674] upd61151: Transfer IRQ status 0x2 [ 52.127474] upd61151: Transfer IRQ status 0x2 [ 52.151273] upd61151: Transfer IRQ status 0x2 [ 52.175072] upd61151: Transfer IRQ status 0x2 [ 52.198874] upd61151: Transfer IRQ status 0x2 [ 52.222672] upd61151: Transfer IRQ status 0x2 [ 52.246474] upd61151: Transfer IRQ status 0x2 [ 52.270272] upd61151: Transfer IRQ status 0x2 [ 52.294074] upd61151: Transfer IRQ status 0x2 [ 52.317873] upd61151: Transfer IRQ status 0x2 [ 52.341674] upd61151: Transfer IRQ status 0x2 [ 52.365472] upd61151: Transfer IRQ status 0x2 [ 52.389274] upd61151: Transfer IRQ status 0x2 [ 52.413073] upd61151: Transfer IRQ status 0x2 [ 52.436873] upd61151: Transfer IRQ status 0x2 [ 52.460672] upd61151: Transfer IRQ status 0x2 [ 52.484670] upd61151: Transfer IRQ status 0x2 [ 52.508459] upd61151: Transfer IRQ status 0x2 [ 52.532260] upd61151: Transfer IRQ status 0x2 [ 52.556055] upd61151: Transfer IRQ status 0x2 [ 52.579856] upd61151: Transfer IRQ status 0x2 [ 52.603651] upd61151: Transfer IRQ status 0x2 [ 52.627447] upd61151: Transfer IRQ status 0x2 [ 52.651246] upd61151: Transfer IRQ status 0x2 [ 52.675042] upd61151: Transfer IRQ status 0x2 [ 52.698844] upd61151: Transfer IRQ status 0x2 [ 52.722641] upd61151: Transfer IRQ status 0x2 [ 52.746440] upd61151: Transfer IRQ status 0x2 [ 52.770234] upd61151: Transfer IRQ status 0x2 [ 52.794035] upd61151: Transfer IRQ status 0x2 [ 52.817838] upd61151: Transfer IRQ status 0x2 [ 52.841642] upd61151: Transfer IRQ status 0x2 [ 52.865437] upd61151: Transfer IRQ status 0x2 [ 52.889237] upd61151: Transfer IRQ status 0x2 [ 52.913035] upd61151: Transfer IRQ status 0x2 [ 52.936835] upd61151: Transfer IRQ status 0x2 [ 52.960630] upd61151: Transfer IRQ status 0x2 [ 52.984419] upd61151: Transfer IRQ status 0x2 [ 53.008218] upd61151: Transfer IRQ status 0x2 [ 53.032021] upd61151: Transfer IRQ status 0x2 [ 53.055820] upd61151: Transfer IRQ status 0x2 [ 53.079619] upd61151: Transfer IRQ status 0x2 [ 53.103421] upd61151: Transfer IRQ status 0x2 [ 53.127220] upd61151: Transfer IRQ status 0x2 [ 53.151024] upd61151: Transfer IRQ status 0x2 [ 53.174821] upd61151: Transfer IRQ status 0x2 [ 53.198623] upd61151: Transfer IRQ status 0x2 [ 53.222422] upd61151: Transfer IRQ status 0x2 [ 53.246223] upd61151: Transfer IRQ status 0x2 [ 53.270022] upd61151: Transfer IRQ status 0x2 [ 53.293824] upd61151: Transfer IRQ status 0x2 [ 53.317621] upd61151: Transfer IRQ status 0x2 [ 53.341422] upd61151: Transfer IRQ status 0x2 [ 53.365220] upd61151: Transfer IRQ status 0x2 [ 53.389024] upd61151: Transfer IRQ status 0x2 [ 53.412826] upd61151: Transfer IRQ status 0x2 [ 53.436626] upd61151: Transfer IRQ status 0x2 [ 53.460413] upd61151: Transfer IRQ status 0x2 [ 53.484231] upd61151: Transfer IRQ status 0x2 [ 53.508029] upd61151: Transfer IRQ status 0x2 [ 53.531827] upd61151: Transfer IRQ status 0x2 [ 53.555627] upd61151: Transfer IRQ status 0x2 [ 53.579425] upd61151: Transfer IRQ status 0x2 [ 53.603224] upd61151: Transfer IRQ status 0x2 [ 53.627018] upd61151: Transfer IRQ status 0x2 [ 53.650820] upd61151: Transfer IRQ status 0x2 [ 53.674617] upd61151: Transfer IRQ status 0x2 [ 53.698418] upd61151: Transfer IRQ status 0x2 [ 53.722216] upd61151: Transfer IRQ status 0x2 [ 53.746019] upd61151: Transfer IRQ status 0x2 [ 53.769817] upd61151: Transfer IRQ status 0x2 [ 53.793618] upd61151: Transfer IRQ status 0x2 [ 53.817443] upd61151: Transfer IRQ status 0x2 [ 53.841246] upd61151: Transfer IRQ status 0x2 [ 53.865044] upd61151: Transfer IRQ status 0x2 [ 53.888846] upd61151: Transfer IRQ status 0x2 [ 53.912644] upd61151: Transfer IRQ status 0x2 [ 53.936435] upd61151: Transfer IRQ status 0x2 [ 53.960233] upd61151: Transfer IRQ status 0x2 [ 53.984035] upd61151: Transfer IRQ status 0x2 [ 54.007833] upd61151: Transfer IRQ status 0x2 [ 54.031631] upd61151: Transfer IRQ status 0x2 [ 54.055433] upd61151: Transfer IRQ status 0x2 [ 54.079230] upd61151: Transfer IRQ status 0x2 [ 54.103030] upd61151: Transfer IRQ status 0x2 [ 54.126828] upd61151: Transfer IRQ status 0x2 [ 54.150631] upd61151: Transfer IRQ status 0x2 [ 54.174428] upd61151: Transfer IRQ status 0x2 [ 54.198228] upd61151: Transfer IRQ status 0x2 [ 54.222026] upd61151: Transfer IRQ status 0x2 [ 54.245827] upd61151: Transfer IRQ status 0x2 [ 54.269624] upd61151: Transfer IRQ status 0x2 [ 54.293426] upd61151: Transfer IRQ status 0x2 [ 54.317223] upd61151: Transfer IRQ status 0x2 [ 54.341024] upd61151: Transfer IRQ status 0x2 [ 54.364821] upd61151: Transfer IRQ status 0x2 [ 54.388621] upd61151: Transfer IRQ status 0x2 [ 54.412408] upd61151: Transfer IRQ status 0x2 [ 54.436209] upd61151: Transfer IRQ status 0x2 [ 54.460007] upd61151: Transfer IRQ status 0x2 [ 54.483824] upd61151: Transfer IRQ status 0x2 [ 54.507626] upd61151: Transfer IRQ status 0x2 [ 54.531422] upd61151: Transfer IRQ status 0x2 [ 54.555223] upd61151: Transfer IRQ status 0x2 [ 54.579020] upd61151: Transfer IRQ status 0x2 [ 54.602822] upd61151: Transfer IRQ status 0x2 [ 54.626620] upd61151: Transfer IRQ status 0x2 [ 54.650421] upd61151: Transfer IRQ status 0x2 [ 54.674217] upd61151: Transfer IRQ status 0x2 [ 54.698018] upd61151: Transfer IRQ status 0x2 [ 54.721816] upd61151: Transfer IRQ status 0x2 [ 54.745616] upd61151: Transfer IRQ status 0x2 [ 54.769414] upd61151: Transfer IRQ status 0x2 [ 54.793215] upd61151: Transfer IRQ status 0x2 [ 54.817014] upd61151: Transfer IRQ status 0x2 [ 54.840815] upd61151: Transfer IRQ status 0x2 [ 54.864614] upd61151: Transfer IRQ status 0x2 [ 54.888404] upd61151: Transfer IRQ status 0x2 [ 54.912203] upd61151: Transfer IRQ status 0x2 [ 54.936005] upd61151: Transfer IRQ status 0x2 [ 54.959804] upd61151: Transfer IRQ status 0x2 [ 54.983601] upd61151: Transfer IRQ status 0x2 [ 55.007405] upd61151: Transfer IRQ status 0x2 [ 55.031203] upd61151: Transfer IRQ status 0x2 [ 55.055004] upd61151: Transfer IRQ status 0x2 [ 55.078802] upd61151: Transfer IRQ status 0x2 [ 55.102603] upd61151: Transfer IRQ status 0x2 [ 55.126401] upd61151: Transfer IRQ status 0x2 [ 55.150202] upd61151: Transfer IRQ status 0x2 [ 55.174000] upd61151: Transfer IRQ status 0x2 [ 55.197802] upd61151: Transfer IRQ status 0x2 [ 55.221599] upd61151: Transfer IRQ status 0x2 [ 55.245398] upd61151: Transfer IRQ status 0x2 [ 55.269196] upd61151: Transfer IRQ status 0x2 [ 55.292997] upd61151: Transfer IRQ status 0x2 [ 55.316794] upd61151: Transfer IRQ status 0x2 [ 55.340595] upd61151: Transfer IRQ status 0x2 [ 55.364383] upd61151: Transfer IRQ status 0x2 [ 55.388184] upd61151: Transfer IRQ status 0x2 [ 55.411983] upd61151: Transfer IRQ status 0x2 [ 55.435779] upd61151: Transfer IRQ status 0x2 [ 55.459581] upd61151: Transfer IRQ status 0x2 [ 55.483393] upd61151: Transfer IRQ status 0x2 [ 55.507195] upd61151: Transfer IRQ status 0x2 [ 55.530992] upd61151: Transfer IRQ status 0x2 [ 55.554793] upd61151: Transfer IRQ status 0x2 [ 55.578591] upd61151: Transfer IRQ status 0x2 [ 55.602391] upd61151: Transfer IRQ status 0x2 [ 55.626189] upd61151: Transfer IRQ status 0x2 [ 55.649991] upd61151: Transfer IRQ status 0x2 [ 55.673788] upd61151: Transfer IRQ status 0x2 [ 55.697606] upd61151: Transfer IRQ status 0x2 [ 55.721404] upd61151: Transfer IRQ status 0x2 [ 55.745206] upd61151: Transfer IRQ status 0x2 [ 55.769003] upd61151: Transfer IRQ status 0x2 [ 55.792804] upd61151: Transfer IRQ status 0x2 [ 55.816633] upd61151: Transfer IRQ status 0x2 [ 55.840426] upd61151: Transfer IRQ status 0x2 [ 55.864222] upd61151: Transfer IRQ status 0x2 [ 55.888018] upd61151: Transfer IRQ status 0x2 [ 55.911820] upd61151: Transfer IRQ status 0x2 [ 55.935618] upd61151: Transfer IRQ status 0x2 [ 55.959420] upd61151: Transfer IRQ status 0x2 [ 55.983214] upd61151: Transfer IRQ status 0x2 [ 56.007017] upd61151: Transfer IRQ status 0x2 [ 56.030816] upd61151: Transfer IRQ status 0x2 [ 56.054618] upd61151: Transfer IRQ status 0x2 [ 56.078417] upd61151: Transfer IRQ status 0x2 [ 56.102219] upd61151: Transfer IRQ status 0x2 [ 56.126018] upd61151: Transfer IRQ status 0x2 [ 56.149820] upd61151: Transfer IRQ status 0x2 [ 56.173619] upd61151: Transfer IRQ status 0x2 [ 56.197419] upd61151: Transfer IRQ status 0x2 [ 56.221217] upd61151: Transfer IRQ status 0x2 [ 56.245019] upd61151: Transfer IRQ status 0x2 [ 56.268816] upd61151: Transfer IRQ status 0x2 [ 56.292616] upd61151: Transfer IRQ status 0x2 [ 56.316404] upd61151: Transfer IRQ status 0x2 [ 56.340203] upd61151: Transfer IRQ status 0x2 [ 56.364005] upd61151: Transfer IRQ status 0x2 [ 56.387804] upd61151: Transfer IRQ status 0x2 [ 56.411606] upd61151: Transfer IRQ status 0x2 [ 56.435405] upd61151: Transfer IRQ status 0x2 [ 56.459209] upd61151: Transfer IRQ status 0x2 [ 56.483029] upd61151: Transfer IRQ status 0x2 [ 56.506831] upd61151: Transfer IRQ status 0x2 [ 56.530626] upd61151: Transfer IRQ status 0x2 [ 56.554428] upd61151: Transfer IRQ status 0x2 [ 56.578225] upd61151: Transfer IRQ status 0x2 [ 56.602026] upd61151: Transfer IRQ status 0x2 [ 56.625825] upd61151: Transfer IRQ status 0x2 [ 56.649628] upd61151: Transfer IRQ status 0x2 [ 56.673427] upd61151: Transfer IRQ status 0x2 [ 56.697230] upd61151: Transfer IRQ status 0x2 [ 56.721026] upd61151: Transfer IRQ status 0x2 [ 56.744827] upd61151: Transfer IRQ status 0x2 [ 56.768626] upd61151: Transfer IRQ status 0x2 [ 56.792418] upd61151: Transfer IRQ status 0x2 [ 56.816220] upd61151: Transfer IRQ status 0x2 [ 56.840019] upd61151: Transfer IRQ status 0x2 [ 56.863821] upd61151: Transfer IRQ status 0x2 [ 56.887620] upd61151: Transfer IRQ status 0x2 [ 56.911424] upd61151: Transfer IRQ status 0x2 [ 56.935223] upd61151: Transfer IRQ status 0x2 [ 56.959024] upd61151: Transfer IRQ status 0x2 [ 56.982823] upd61151: Transfer IRQ status 0x2 [ 57.006626] upd61151: Transfer IRQ status 0x2 [ 57.030426] upd61151: Transfer IRQ status 0x2 [ 57.054228] upd61151: Transfer IRQ status 0x2 [ 57.078025] upd61151: Transfer IRQ status 0x2 [ 57.101827] upd61151: Transfer IRQ status 0x2 [ 57.125625] upd61151: Transfer IRQ status 0x2 [ 57.149428] upd61151: Transfer IRQ status 0x2 [ 57.173227] upd61151: Transfer IRQ status 0x2 [ 57.197028] upd61151: Transfer IRQ status 0x2 [ 57.220826] upd61151: Transfer IRQ status 0x2 [ 57.244628] upd61151: Transfer IRQ status 0x2 [ 57.268415] upd61151: Transfer IRQ status 0x2 [ 57.292211] upd61151: Transfer IRQ status 0x2 [ 57.316014] upd61151: Transfer IRQ status 0x2 [ 57.339811] upd61151: Transfer IRQ status 0x2 [ 57.363613] upd61151: Transfer IRQ status 0x2 [ 57.387411] upd61151: Transfer IRQ status 0x2 [ 57.411213] upd61151: Transfer IRQ status 0x2 [ 57.435010] upd61151: Transfer IRQ status 0x2 [ 57.458813] upd61151: Transfer IRQ status 0x2 [ 57.482625] upd61151: Transfer IRQ status 0x2 [ 57.506425] upd61151: Transfer IRQ status 0x2 [ 57.530219] upd61151: Transfer IRQ status 0x2 [ 57.554020] upd61151: Transfer IRQ status 0x2 [ 57.577818] upd61151: Transfer IRQ status 0x2 [ 57.601620] upd61151: Transfer IRQ status 0x2 [ 57.625414] upd61151: Transfer IRQ status 0x2 [ 57.649215] upd61151: Transfer IRQ status 0x2 [ 57.673011] upd61151: Transfer IRQ status 0x2 [ 57.696814] upd61151: Transfer IRQ status 0x2 [ 57.720613] upd61151: Transfer IRQ status 0x2 [ 57.744402] upd61151: Transfer IRQ status 0x2 [ 57.768203] upd61151: Transfer IRQ status 0x2 [ 57.792002] upd61151: Transfer IRQ status 0x2 [ 57.815820] upd61151: Transfer IRQ status 0x2 [ 57.839620] upd61151: Transfer IRQ status 0x2 [ 57.863423] upd61151: Transfer IRQ status 0x2 [ 57.887222] upd61151: Transfer IRQ status 0x2 [ 57.911025] upd61151: Transfer IRQ status 0x2 [ 57.934822] upd61151: Transfer IRQ status 0x2 [ 57.958626] upd61151: Transfer IRQ status 0x2 [ 57.982424] upd61151: Transfer IRQ status 0x2 [ 58.006228] upd61151: Transfer IRQ status 0x2 [ 58.030026] upd61151: Transfer IRQ status 0x2 [ 58.053827] upd61151: Transfer IRQ status 0x2 [ 58.077625] upd61151: Transfer IRQ status 0x2 [ 58.101427] upd61151: Transfer IRQ status 0x2 [ 58.125225] upd61151: Transfer IRQ status 0x2 [ 58.149028] upd61151: Transfer IRQ status 0x2 [ 58.172826] upd61151: Transfer IRQ status 0x2 [ 58.196628] upd61151: Transfer IRQ status 0x2 [ 58.220417] upd61151: Transfer IRQ status 0x2 [ 58.244214] upd61151: Transfer IRQ status 0x2 [ 58.268016] upd61151: Transfer IRQ status 0x2 [ 58.291814] upd61151: Transfer IRQ status 0x2 [ 58.315616] upd61151: Transfer IRQ status 0x2 [ 58.339416] upd61151: Transfer IRQ status 0x2 [ 58.363218] upd61151: Transfer IRQ status 0x2 [ 58.387017] upd61151: Transfer IRQ status 0x2 [ 58.410820] upd61151: Transfer IRQ status 0x2 [ 58.434619] upd61151: Transfer IRQ status 0x2 [ 58.458420] upd61151: Transfer IRQ status 0x2 [ 58.482236] upd61151: Transfer IRQ status 0x2 [ 58.506039] upd61151: Transfer IRQ status 0x2 [ 58.529837] upd61151: Transfer IRQ status 0x2 [ 58.553638] upd61151: Transfer IRQ status 0x2 [ 58.577436] upd61151: Transfer IRQ status 0x2 [ 58.601238] upd61151: Transfer IRQ status 0x2 [ 58.625036] upd61151: Transfer IRQ status 0x2 [ 58.648837] upd61151: Transfer IRQ status 0x2 [ 58.672635] upd61151: Transfer IRQ status 0x2 [ 58.696422] upd61151: Transfer IRQ status 0x2 [ 58.720223] upd61151: Transfer IRQ status 0x2 [ 58.744020] upd61151: Transfer IRQ status 0x2 [ 58.767822] upd61151: Transfer IRQ status 0x2 [ 58.791618] upd61151: Transfer IRQ status 0x2 [ 58.815423] upd61151: Transfer IRQ status 0x2 [ 58.839222] upd61151: Transfer IRQ status 0x2 [ 58.863026] upd61151: Transfer IRQ status 0x2 [ 58.886824] upd61151: Transfer IRQ status 0x2 [ 58.910625] upd61151: Transfer IRQ status 0x2 [ 58.934422] upd61151: Transfer IRQ status 0x1 [ 58.934606] fw upload stop [ 58.934834] upd61151: audio firmware upload complete... [ 58.935073] upd61151: IRQ status 0x19 [ 58.935256] DEBUG uPD61151: upd61151_chip_command [ 58.935484] upd61151: IRQ error status 0x0 [ 58.935850] upd61151: MPEG2 core status 0 [ 58.936034] upd61151: IRQ error status 0x0 [ 58.948204] upd61151: MPEG2 core status 1 [ 58.948388] upd61151: IRQ status 0x8 [ 58.948576] upd61151: SetState 1 SUCCESS, delay [10 ms]. [ 58.948577] upd61151_setup_video_frontend [ 58.948622] dbyte = 0x0 0x0 0x0 [ 58.949646] upd61151_setup_audio_frontend [ 58.950619] upd61151_config_encoder [ 58.950662] upd61151_set_state [ 58.950705] DEBUG uPD61151: upd61151_chip_command [ 58.950932] upd61151: IRQ error status 0x0 [ 58.951299] upd61151: MPEG2 core status 1 [ 58.951483] upd61151: IRQ status 0x0 [ 58.951484] upd61151: SetState 1 SUCCESS, delay [0 ms]. [ 58.951485] Firmware downloaded SUCCESS!!! [ 58.951643] saa7133[0]: registered device video0 [v4l2] [ 58.951709] saa7133[0]: registered device vbi0 [ 58.951771] saa7133[0]: registered device radio0 [ 58.993549] saa7133[0]: registered device video1 [mpeg] [ 59.017327] saa7134 ALSA driver for DMA sound loaded [ 59.017387] IRQ 19/saa7133[0]: IRQF_DISABLED is not guaranteed on shared IRQs [ 59.017449] saa7133[0]/alsa: saa7133[0] at 0xe5100000 irq 19 registered as card -1
[ 72.129075] xc5000: I2C write failed (len=4) [ 72.232014] xc5000: I2C write failed (len=4) [ 72.235009] xc5000: I2C read failed [ 72.235060] xc5000: I2C read failed [ 72.235104] xc5000: waiting for firmware upload (dvb-fe-xc5000-1.6.114.fw)... [ 72.235152] saa7134 0000:04:01.0: firmware: requesting dvb-fe-xc5000-1.6.114.fw [ 72.384735] xc5000: firmware read 12401 bytes. [ 72.384739] xc5000: firmware uploading... [ 75.716007] xc5000: firmware upload complete... [ 76.468008] DEBUG uPD61151: upd61151_s_std [ 76.468059] set standart to 255 [ 76.468107] DEBUG uPD61151: upd61151_s_std [ 76.468155] set standart to 255 [ 76.940008] DEBUG uPD61151: upd61151_s_std [ 76.940061] set standart to 255 [ 76.940109] DEBUG uPD61151: upd61151_s_std [ 76.940157] set standart to 255
With my best regards, Dmitry.
linux/drivers/media/video/saa7134/Makefile +2 -2
@@ -1,9 +1,9 @@ saa7134-objs := saa7134-cards.o saa7134-core.o saa7134-i2c.o \ saa7134-ts.o saa7134-tvaudio.o saa7134-vbi.o \ - saa7134-video.o saa7134-input.o + saa7134-video.o saa7134-input.o saa7134-spi.o -obj-$(CONFIG_VIDEO_SAA7134) += saa6752hs.o saa7134.o saa7134-empress.o +obj-$(CONFIG_VIDEO_SAA7134) += saa6752hs.o saa7134.o saa7134-empress.o upd61151.o obj-$(CONFIG_VIDEO_SAA7134_ALSA) += saa7134-alsa.o
linux/drivers/media/video/saa7134/saa7134-cards.c +39 -8
80 lines not on this page · raw message
linux/drivers/media/video/saa7134/saa7134-core.c +48 -3
78 lines not on this page · raw message
linux/drivers/media/video/saa7134/saa7134.h +44 -0
98 lines not on this page · raw message
linux/drivers/media/video/v4l2-common.c +62 -0
74 lines not on this page · raw message
linux/include/media/v4l2-common.h +19 -0
@@ -191,6 +191,25 @@/* ------------------------------------------------------------------------- */ +/* SPI Helper functions */ + +#include <linux/spi/spi.h> + +struct spi_device_id ; +struct spi_device ; + +/* Load an spi module and return an initialized v4l2_subdev struct. +Only call request_module if module_name != NULL. +The client_type argument is the name of the chip that's on the adapter. */ +struct v4l2_subdev *v4l2_spi_new_subdev (struct v4l2_device *v4l2_dev, +struct spi_master *master,struct spi_board_info *info); + +/* Initialize an v4l2_subdev with data from an spi_device struct */ +void v4l2_spi_subdev_init (struct v4l2_subdev *sd,struct spi_device *spi, +const struct v4l2_subdev_ops *ops); + +/* ------------------------------------------------------------------------- */ +/* Note: these remaining ioctls/structs should be removed as well, but they are still used in tuner-simple.c (TUNER_SET_CONFIG), cx18/ivtv (RESET) and v4l2-int-device.h (v4l2_routing). To remove these ioctls some more cleanup
linux/include/media/v4l2-subdev.h +2 -0
@@ -387,6 +387,8 @@/* Set this flag if this subdev is a i2c device. */ #define V4L2_SUBDEV_FL_IS_I2C (1U << 0) +/* Set this flag if this subdev is a spi device. */ +#define V4L2_SUBDEV_FL_IS_SPI (1U << 1)/* Each instance of a subdev driver should create this struct, either stand-alone or embedded in a larger struct.
[ 4.901675] Linux video capture interface: v2.00 [ 5.046878] saa7130/34: v4l2 driver version 0.2.15 loaded [ 5.046964] saa7134 0000:04:01.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19 [ 5.047018] saa7133[0]: found at 0000:04:01.0, rev: 209, irq: 19, latency: 32, mmio: 0xe5100000 [ 5.047080] saa7133[0]: subsystem: 5ace:7595, board: Beholder BeholdTV X7 [card=171,autodetected] [ 5.047153] saa7133[0]: board init: gpio is 200000 [ 5.047205] IRQ 19/saa7133[0]: IRQF_DISABLED is not guaranteed on shared IRQs [ 5.196517] saa7133[0]: i2c eeprom 00: ce 5a<6>HDA Intel 0000:00:1b.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 5.196620] HDA Intel 0000:00:1b.0: setting latency timer to 64 [ 5.196687] 95 75 54 20 00 00 00 00 00 00 00 00 00 01 [ 5.197190] saa7133[0]: i2c eeprom 10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 5.197787] saa7133[0]: i2c eeprom 20: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 5.198385] saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 5.198982] saa7133[0]: i2c eeprom 40: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 5.199579] saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 5.200176] saa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 5.200785] saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 5.201382] saa7133[0]: i2c eeprom 80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 5.201979] saa7133[0]: i2c eeprom 90: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 5.202576] saa7133[0]: i2c eeprom a0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 5.203174] saa7133[0]: i2c eeprom b0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 5.203771] saa7133[0]: i2c eeprom c0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 5.204371] saa7133[0]: i2c eeprom d0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 5.204982] saa7133[0]: i2c eeprom e0: 00 00 00 00 ff ff ff ff ff ff ff ff ff ff ff ff [ 5.205579] saa7133[0]: i2c eeprom f0: 42 54 56 30 30 30 30 ff ff ff ff ff ff ff ff ff [ 5.228577] tuner 1-0061: chip found @ 0xc2 (saa7133[0]) [ 5.286091] xc5000 1-0061: creating new instance [ 5.292505] xc5000: Successfully identified at address 0x61 [ 5.292552] xc5000: Firmware has not been loaded previously [ 33.571875] saa7134 0000:04:01.0: spi master registered: bus_num=32766 num_chipselect=1 [ 33.571933] saa7133[0]: found muPD61151 MPEG encoder [ 33.601819] upd61151_probe function [ 33.602057] upd61151: MPEG2 core status 0 [ 33.602058] upd61151: need reload firmware [ 33.602059] Start load firmware... [ 33.602103] DEBUG: upd61151_download_firmware [ 33.603325] DEBUG: upd61151_load_base_firmware [ 33.603370] upd61151: waiting for base firmware upload (D61151_PS_7133_v22_031031.bin)... [ 33.603427] saa7134 0000:04:01.0: firmware: requesting D61151_PS_7133_v22_031031.bin [ 33.676430] upd61151: firmware read 97002 bytes. [ 33.676432] upd61151: base firmware uploading... [ 33.677071] upd61151: Transfer IRQ status 0x0 [ 33.678539] fw upload start [ 51.433446] fw upload stop [ 51.433677] upd61151: Transfer IRQ status 0x1 [ 51.434043] upd61151: base firmware upload complete... [ 51.434285] DEBUG: upd61151_load_audio_firmware [ 51.434330] upd61151: waiting for audio firmware upload (audrey_MPE_V1r51.bin)... [ 51.434386] saa7134 0000:04:01.0: firmware: requesting audrey_MPE_V1r51.bin [ 51.482980] upd61151: firmware read 40064 bytes. [ 51.482982] upd61151: audio firmware uploading... [ 51.483231] upd61151: Transfer IRQ status 0x1 [ 51.484700] fw upload start [ 51.508682] upd61151: Transfer IRQ status 0x2 [ 51.532479] upd61151: Transfer IRQ status 0x2 [ 51.556280] upd61151: Transfer IRQ status 0x2 [ 51.580081] upd61151: Transfer IRQ status 0x2 [ 51.603877] upd61151: Transfer IRQ status 0x2 [ 51.627677] upd61151: Transfer IRQ status 0x2 [ 51.651476] upd61151: Transfer IRQ status 0x2 [ 51.675275] upd61151: Transfer IRQ status 0x2 [ 51.699072] upd61151: Transfer IRQ status 0x2 [ 51.722870] upd61151: Transfer IRQ status 0x2 [ 51.746669] upd61151: Transfer IRQ status 0x2 [ 51.770467] upd61151: Transfer IRQ status 0x2 [ 51.794267] upd61151: Transfer IRQ status 0x2 [ 51.818092] upd61151: Transfer IRQ status 0x2 [ 51.841896] upd61151: Transfer IRQ status 0x2 [ 51.865691] upd61151: Transfer IRQ status 0x2 [ 51.889493] upd61151: Transfer IRQ status 0x2 [ 51.913290] upd61151: Transfer IRQ status 0x2 [ 51.937091] upd61151: Transfer IRQ status 0x2 [ 51.960889] upd61151: Transfer IRQ status 0x2 [ 51.984690] upd61151: Transfer IRQ status 0x2 [ 52.008479] upd61151: Transfer IRQ status 0x2 [ 52.032279] upd61151: Transfer IRQ status 0x2 [ 52.056076] upd61151: Transfer IRQ status 0x2 [ 52.079877] upd61151: Transfer IRQ status 0x2 [ 52.103674] upd61151: Transfer IRQ status 0x2 [ 52.127474] upd61151: Transfer IRQ status 0x2 [ 52.151273] upd61151: Transfer IRQ status 0x2 [ 52.175072] upd61151: Transfer IRQ status 0x2 [ 52.198874] upd61151: Transfer IRQ status 0x2 [ 52.222672] upd61151: Transfer IRQ status 0x2 [ 52.246474] upd61151: Transfer IRQ status 0x2 [ 52.270272] upd61151: Transfer IRQ status 0x2 [ 52.294074] upd61151: Transfer IRQ status 0x2 [ 52.317873] upd61151: Transfer IRQ status 0x2 [ 52.341674] upd61151: Transfer IRQ status 0x2 [ 52.365472] upd61151: Transfer IRQ status 0x2 [ 52.389274] upd61151: Transfer IRQ status 0x2 [ 52.413073] upd61151: Transfer IRQ status 0x2 [ 52.436873] upd61151: Transfer IRQ status 0x2 [ 52.460672] upd61151: Transfer IRQ status 0x2 [ 52.484670] upd61151: Transfer IRQ status 0x2 [ 52.508459] upd61151: Transfer IRQ status 0x2 [ 52.532260] upd61151: Transfer IRQ status 0x2 [ 52.556055] upd61151: Transfer IRQ status 0x2 [ 52.579856] upd61151: Transfer IRQ status 0x2 [ 52.603651] upd61151: Transfer IRQ status 0x2 [ 52.627447] upd61151: Transfer IRQ status 0x2 [ 52.651246] upd61151: Transfer IRQ status 0x2 [ 52.675042] upd61151: Transfer IRQ status 0x2 [ 52.698844] upd61151: Transfer IRQ status 0x2 [ 52.722641] upd61151: Transfer IRQ status 0x2 [ 52.746440] upd61151: Transfer IRQ status 0x2 [ 52.770234] upd61151: Transfer IRQ status 0x2 [ 52.794035] upd61151: Transfer IRQ status 0x2 [ 52.817838] upd61151: Transfer IRQ status 0x2 [ 52.841642] upd61151: Transfer IRQ status 0x2 [ 52.865437] upd61151: Transfer IRQ status 0x2 [ 52.889237] upd61151: Transfer IRQ status 0x2 [ 52.913035] upd61151: Transfer IRQ status 0x2 [ 52.936835] upd61151: Transfer IRQ status 0x2 [ 52.960630] upd61151: Transfer IRQ status 0x2 [ 52.984419] upd61151: Transfer IRQ status 0x2 [ 53.008218] upd61151: Transfer IRQ status 0x2 [ 53.032021] upd61151: Transfer IRQ status 0x2 [ 53.055820] upd61151: Transfer IRQ status 0x2 [ 53.079619] upd61151: Transfer IRQ status 0x2 [ 53.103421] upd61151: Transfer IRQ status 0x2 [ 53.127220] upd61151: Transfer IRQ status 0x2 [ 53.151024] upd61151: Transfer IRQ status 0x2 [ 53.174821] upd61151: Transfer IRQ status 0x2 [ 53.198623] upd61151: Transfer IRQ status 0x2 [ 53.222422] upd61151: Transfer IRQ status 0x2 [ 53.246223] upd61151: Transfer IRQ status 0x2 [ 53.270022] upd61151: Transfer IRQ status 0x2 [ 53.293824] upd61151: Transfer IRQ status 0x2 [ 53.317621] upd61151: Transfer IRQ status 0x2 [ 53.341422] upd61151: Transfer IRQ status 0x2 [ 53.365220] upd61151: Transfer IRQ status 0x2 [ 53.389024] upd61151: Transfer IRQ status 0x2 [ 53.412826] upd61151: Transfer IRQ status 0x2 [ 53.436626] upd61151: Transfer IRQ status 0x2 [ 53.460413] upd61151: Transfer IRQ status 0x2 [ 53.484231] upd61151: Transfer IRQ status 0x2 [ 53.508029] upd61151: Transfer IRQ status 0x2 [ 53.531827] upd61151: Transfer IRQ status 0x2 [ 53.555627] upd61151: Transfer IRQ status 0x2 [ 53.579425] upd61151: Transfer IRQ status 0x2 [ 53.603224] upd61151: Transfer IRQ status 0x2 [ 53.627018] upd61151: Transfer IRQ status 0x2 [ 53.650820] upd61151: Transfer IRQ status 0x2 [ 53.674617] upd61151: Transfer IRQ status 0x2 [ 53.698418] upd61151: Transfer IRQ status 0x2 [ 53.722216] upd61151: Transfer IRQ status 0x2 [ 53.746019] upd61151: Transfer IRQ status 0x2 [ 53.769817] upd61151: Transfer IRQ status 0x2 [ 53.793618] upd61151: Transfer IRQ status 0x2 [ 53.817443] upd61151: Transfer IRQ status 0x2 [ 53.841246] upd61151: Transfer IRQ status 0x2 [ 53.865044] upd61151: Transfer IRQ status 0x2 [ 53.888846] upd61151: Transfer IRQ status 0x2 [ 53.912644] upd61151: Transfer IRQ status 0x2 [ 53.936435] upd61151: Transfer IRQ status 0x2 [ 53.960233] upd61151: Transfer IRQ status 0x2 [ 53.984035] upd61151: Transfer IRQ status 0x2 [ 54.007833] upd61151: Transfer IRQ status 0x2 [ 54.031631] upd61151: Transfer IRQ status 0x2 [ 54.055433] upd61151: Transfer IRQ status 0x2 [ 54.079230] upd61151: Transfer IRQ status 0x2 [ 54.103030] upd61151: Transfer IRQ status 0x2 [ 54.126828] upd61151: Transfer IRQ status 0x2 [ 54.150631] upd61151: Transfer IRQ status 0x2 [ 54.174428] upd61151: Transfer IRQ status 0x2 [ 54.198228] upd61151: Transfer IRQ status 0x2 [ 54.222026] upd61151: Transfer IRQ status 0x2 [ 54.245827] upd61151: Transfer IRQ status 0x2 [ 54.269624] upd61151: Transfer IRQ status 0x2 [ 54.293426] upd61151: Transfer IRQ status 0x2 [ 54.317223] upd61151: Transfer IRQ status 0x2 [ 54.341024] upd61151: Transfer IRQ status 0x2 [ 54.364821] upd61151: Transfer IRQ status 0x2 [ 54.388621] upd61151: Transfer IRQ status 0x2 [ 54.412408] upd61151: Transfer IRQ status 0x2 [ 54.436209] upd61151: Transfer IRQ status 0x2 [ 54.460007] upd61151: Transfer IRQ status 0x2 [ 54.483824] upd61151: Transfer IRQ status 0x2 [ 54.507626] upd61151: Transfer IRQ status 0x2 [ 54.531422] upd61151: Transfer IRQ status 0x2 [ 54.555223] upd61151: Transfer IRQ status 0x2 [ 54.579020] upd61151: Transfer IRQ status 0x2 [ 54.602822] upd61151: Transfer IRQ status 0x2 [ 54.626620] upd61151: Transfer IRQ status 0x2 [ 54.650421] upd61151: Transfer IRQ status 0x2 [ 54.674217] upd61151: Transfer IRQ status 0x2 [ 54.698018] upd61151: Transfer IRQ status 0x2 [ 54.721816] upd61151: Transfer IRQ status 0x2 [ 54.745616] upd61151: Transfer IRQ status 0x2 [ 54.769414] upd61151: Transfer IRQ status 0x2 [ 54.793215] upd61151: Transfer IRQ status 0x2 [ 54.817014] upd61151: Transfer IRQ status 0x2 [ 54.840815] upd61151: Transfer IRQ status 0x2 [ 54.864614] upd61151: Transfer IRQ status 0x2 [ 54.888404] upd61151: Transfer IRQ status 0x2 [ 54.912203] upd61151: Transfer IRQ status 0x2 [ 54.936005] upd61151: Transfer IRQ status 0x2 [ 54.959804] upd61151: Transfer IRQ status 0x2 [ 54.983601] upd61151: Transfer IRQ status 0x2 [ 55.007405] upd61151: Transfer IRQ status 0x2 [ 55.031203] upd61151: Transfer IRQ status 0x2 [ 55.055004] upd61151: Transfer IRQ status 0x2 [ 55.078802] upd61151: Transfer IRQ status 0x2 [ 55.102603] upd61151: Transfer IRQ status 0x2 [ 55.126401] upd61151: Transfer IRQ status 0x2 [ 55.150202] upd61151: Transfer IRQ status 0x2 [ 55.174000] upd61151: Transfer IRQ status 0x2 [ 55.197802] upd61151: Transfer IRQ status 0x2 [ 55.221599] upd61151: Transfer IRQ status 0x2 [ 55.245398] upd61151: Transfer IRQ status 0x2 [ 55.269196] upd61151: Transfer IRQ status 0x2 [ 55.292997] upd61151: Transfer IRQ status 0x2 [ 55.316794] upd61151: Transfer IRQ status 0x2 [ 55.340595] upd61151: Transfer IRQ status 0x2 [ 55.364383] upd61151: Transfer IRQ status 0x2 [ 55.388184] upd61151: Transfer IRQ status 0x2 [ 55.411983] upd61151: Transfer IRQ status 0x2 [ 55.435779] upd61151: Transfer IRQ status 0x2 [ 55.459581] upd61151: Transfer IRQ status 0x2 [ 55.483393] upd61151: Transfer IRQ status 0x2 [ 55.507195] upd61151: Transfer IRQ status 0x2 [ 55.530992] upd61151: Transfer IRQ status 0x2 [ 55.554793] upd61151: Transfer IRQ status 0x2 [ 55.578591] upd61151: Transfer IRQ status 0x2 [ 55.602391] upd61151: Transfer IRQ status 0x2 [ 55.626189] upd61151: Transfer IRQ status 0x2 [ 55.649991] upd61151: Transfer IRQ status 0x2 [ 55.673788] upd61151: Transfer IRQ status 0x2 [ 55.697606] upd61151: Transfer IRQ status 0x2 [ 55.721404] upd61151: Transfer IRQ status 0x2 [ 55.745206] upd61151: Transfer IRQ status 0x2 [ 55.769003] upd61151: Transfer IRQ status 0x2 [ 55.792804] upd61151: Transfer IRQ status 0x2 [ 55.816633] upd61151: Transfer IRQ status 0x2 [ 55.840426] upd61151: Transfer IRQ status 0x2 [ 55.864222] upd61151: Transfer IRQ status 0x2 [ 55.888018] upd61151: Transfer IRQ status 0x2 [ 55.911820] upd61151: Transfer IRQ status 0x2 [ 55.935618] upd61151: Transfer IRQ status 0x2 [ 55.959420] upd61151: Transfer IRQ status 0x2 [ 55.983214] upd61151: Transfer IRQ status 0x2 [ 56.007017] upd61151: Transfer IRQ status 0x2 [ 56.030816] upd61151: Transfer IRQ status 0x2 [ 56.054618] upd61151: Transfer IRQ status 0x2 [ 56.078417] upd61151: Transfer IRQ status 0x2 [ 56.102219] upd61151: Transfer IRQ status 0x2 [ 56.126018] upd61151: Transfer IRQ status 0x2 [ 56.149820] upd61151: Transfer IRQ status 0x2 [ 56.173619] upd61151: Transfer IRQ status 0x2 [ 56.197419] upd61151: Transfer IRQ status 0x2 [ 56.221217] upd61151: Transfer IRQ status 0x2 [ 56.245019] upd61151: Transfer IRQ status 0x2 [ 56.268816] upd61151: Transfer IRQ status 0x2 [ 56.292616] upd61151: Transfer IRQ status 0x2 [ 56.316404] upd61151: Transfer IRQ status 0x2 [ 56.340203] upd61151: Transfer IRQ status 0x2 [ 56.364005] upd61151: Transfer IRQ status 0x2 [ 56.387804] upd61151: Transfer IRQ status 0x2 [ 56.411606] upd61151: Transfer IRQ status 0x2 [ 56.435405] upd61151: Transfer IRQ status 0x2 [ 56.459209] upd61151: Transfer IRQ status 0x2 [ 56.483029] upd61151: Transfer IRQ status 0x2 [ 56.506831] upd61151: Transfer IRQ status 0x2 [ 56.530626] upd61151: Transfer IRQ status 0x2 [ 56.554428] upd61151: Transfer IRQ status 0x2 [ 56.578225] upd61151: Transfer IRQ status 0x2 [ 56.602026] upd61151: Transfer IRQ status 0x2 [ 56.625825] upd61151: Transfer IRQ status 0x2 [ 56.649628] upd61151: Transfer IRQ status 0x2 [ 56.673427] upd61151: Transfer IRQ status 0x2 [ 56.697230] upd61151: Transfer IRQ status 0x2 [ 56.721026] upd61151: Transfer IRQ status 0x2 [ 56.744827] upd61151: Transfer IRQ status 0x2 [ 56.768626] upd61151: Transfer IRQ status 0x2 [ 56.792418] upd61151: Transfer IRQ status 0x2 [ 56.816220] upd61151: Transfer IRQ status 0x2 [ 56.840019] upd61151: Transfer IRQ status 0x2 [ 56.863821] upd61151: Transfer IRQ status 0x2 [ 56.887620] upd61151: Transfer IRQ status 0x2 [ 56.911424] upd61151: Transfer IRQ status 0x2 [ 56.935223] upd61151: Transfer IRQ status 0x2 [ 56.959024] upd61151: Transfer IRQ status 0x2 [ 56.982823] upd61151: Transfer IRQ status 0x2 [ 57.006626] upd61151: Transfer IRQ status 0x2 [ 57.030426] upd61151: Transfer IRQ status 0x2 [ 57.054228] upd61151: Transfer IRQ status 0x2 [ 57.078025] upd61151: Transfer IRQ status 0x2 [ 57.101827] upd61151: Transfer IRQ status 0x2 [ 57.125625] upd61151: Transfer IRQ status 0x2 [ 57.149428] upd61151: Transfer IRQ status 0x2 [ 57.173227] upd61151: Transfer IRQ status 0x2 [ 57.197028] upd61151: Transfer IRQ status 0x2 [ 57.220826] upd61151: Transfer IRQ status 0x2 [ 57.244628] upd61151: Transfer IRQ status 0x2 [ 57.268415] upd61151: Transfer IRQ status 0x2 [ 57.292211] upd61151: Transfer IRQ status 0x2 [ 57.316014] upd61151: Transfer IRQ status 0x2 [ 57.339811] upd61151: Transfer IRQ status 0x2 [ 57.363613] upd61151: Transfer IRQ status 0x2 [ 57.387411] upd61151: Transfer IRQ status 0x2 [ 57.411213] upd61151: Transfer IRQ status 0x2 [ 57.435010] upd61151: Transfer IRQ status 0x2 [ 57.458813] upd61151: Transfer IRQ status 0x2 [ 57.482625] upd61151: Transfer IRQ status 0x2 [ 57.506425] upd61151: Transfer IRQ status 0x2 [ 57.530219] upd61151: Transfer IRQ status 0x2 [ 57.554020] upd61151: Transfer IRQ status 0x2 [ 57.577818] upd61151: Transfer IRQ status 0x2 [ 57.601620] upd61151: Transfer IRQ status 0x2 [ 57.625414] upd61151: Transfer IRQ status 0x2 [ 57.649215] upd61151: Transfer IRQ status 0x2 [ 57.673011] upd61151: Transfer IRQ status 0x2 [ 57.696814] upd61151: Transfer IRQ status 0x2 [ 57.720613] upd61151: Transfer IRQ status 0x2 [ 57.744402] upd61151: Transfer IRQ status 0x2 [ 57.768203] upd61151: Transfer IRQ status 0x2 [ 57.792002] upd61151: Transfer IRQ status 0x2 [ 57.815820] upd61151: Transfer IRQ status 0x2 [ 57.839620] upd61151: Transfer IRQ status 0x2 [ 57.863423] upd61151: Transfer IRQ status 0x2 [ 57.887222] upd61151: Transfer IRQ status 0x2 [ 57.911025] upd61151: Transfer IRQ status 0x2 [ 57.934822] upd61151: Transfer IRQ status 0x2 [ 57.958626] upd61151: Transfer IRQ status 0x2 [ 57.982424] upd61151: Transfer IRQ status 0x2 [ 58.006228] upd61151: Transfer IRQ status 0x2 [ 58.030026] upd61151: Transfer IRQ status 0x2 [ 58.053827] upd61151: Transfer IRQ status 0x2 [ 58.077625] upd61151: Transfer IRQ status 0x2 [ 58.101427] upd61151: Transfer IRQ status 0x2 [ 58.125225] upd61151: Transfer IRQ status 0x2 [ 58.149028] upd61151: Transfer IRQ status 0x2 [ 58.172826] upd61151: Transfer IRQ status 0x2 [ 58.196628] upd61151: Transfer IRQ status 0x2 [ 58.220417] upd61151: Transfer IRQ status 0x2 [ 58.244214] upd61151: Transfer IRQ status 0x2 [ 58.268016] upd61151: Transfer IRQ status 0x2 [ 58.291814] upd61151: Transfer IRQ status 0x2 [ 58.315616] upd61151: Transfer IRQ status 0x2 [ 58.339416] upd61151: Transfer IRQ status 0x2 [ 58.363218] upd61151: Transfer IRQ status 0x2 [ 58.387017] upd61151: Transfer IRQ status 0x2 [ 58.410820] upd61151: Transfer IRQ status 0x2 [ 58.434619] upd61151: Transfer IRQ status 0x2 [ 58.458420] upd61151: Transfer IRQ status 0x2 [ 58.482236] upd61151: Transfer IRQ status 0x2 [ 58.506039] upd61151: Transfer IRQ status 0x2 [ 58.529837] upd61151: Transfer IRQ status 0x2 [ 58.553638] upd61151: Transfer IRQ status 0x2 [ 58.577436] upd61151: Transfer IRQ status 0x2 [ 58.601238] upd61151: Transfer IRQ status 0x2 [ 58.625036] upd61151: Transfer IRQ status 0x2 [ 58.648837] upd61151: Transfer IRQ status 0x2 [ 58.672635] upd61151: Transfer IRQ status 0x2 [ 58.696422] upd61151: Transfer IRQ status 0x2 [ 58.720223] upd61151: Transfer IRQ status 0x2 [ 58.744020] upd61151: Transfer IRQ status 0x2 [ 58.767822] upd61151: Transfer IRQ status 0x2 [ 58.791618] upd61151: Transfer IRQ status 0x2 [ 58.815423] upd61151: Transfer IRQ status 0x2 [ 58.839222] upd61151: Transfer IRQ status 0x2 [ 58.863026] upd61151: Transfer IRQ status 0x2 [ 58.886824] upd61151: Transfer IRQ status 0x2 [ 58.910625] upd61151: Transfer IRQ status 0x2 [ 58.934422] upd61151: Transfer IRQ status 0x1 [ 58.934606] fw upload stop [ 58.934834] upd61151: audio firmware upload complete... [ 58.935073] upd61151: IRQ status 0x19 [ 58.935256] DEBUG uPD61151: upd61151_chip_command [ 58.935484] upd61151: IRQ error status 0x0 [ 58.935850] upd61151: MPEG2 core status 0 [ 58.936034] upd61151: IRQ error status 0x0 [ 58.948204] upd61151: MPEG2 core status 1 [ 58.948388] upd61151: IRQ status 0x8 [ 58.948576] upd61151: SetState 1 SUCCESS, delay [10 ms]. [ 58.948577] upd61151_setup_video_frontend [ 58.948622] dbyte = 0x0 0x0 0x0 [ 58.949646] upd61151_setup_audio_frontend [ 58.950619] upd61151_config_encoder [ 58.950662] upd61151_set_state [ 58.950705] DEBUG uPD61151: upd61151_chip_command [ 58.950932] upd61151: IRQ error status 0x0 [ 58.951299] upd61151: MPEG2 core status 1 [ 58.951483] upd61151: IRQ status 0x0 [ 58.951484] upd61151: SetState 1 SUCCESS, delay [0 ms]. [ 58.951485] Firmware downloaded SUCCESS!!! [ 58.951643] saa7133[0]: registered device video0 [v4l2] [ 58.951709] saa7133[0]: registered device vbi0 [ 58.951771] saa7133[0]: registered device radio0 [ 58.993549] saa7133[0]: registered device video1 [mpeg] [ 59.017327] saa7134 ALSA driver for DMA sound loaded [ 59.017387] IRQ 19/saa7133[0]: IRQF_DISABLED is not guaranteed on shared IRQs [ 59.017449] saa7133[0]/alsa: saa7133[0] at 0xe5100000 irq 19 registered as card -1
[ 72.129075] xc5000: I2C write failed (len=4) [ 72.232014] xc5000: I2C write failed (len=4) [ 72.235009] xc5000: I2C read failed [ 72.235060] xc5000: I2C read failed [ 72.235104] xc5000: waiting for firmware upload (dvb-fe-xc5000-1.6.114.fw)... [ 72.235152] saa7134 0000:04:01.0: firmware: requesting dvb-fe-xc5000-1.6.114.fw [ 72.384735] xc5000: firmware read 12401 bytes. [ 72.384739] xc5000: firmware uploading... [ 75.716007] xc5000: firmware upload complete... [ 76.468008] DEBUG uPD61151: upd61151_s_std [ 76.468059] set standart to 255 [ 76.468107] DEBUG uPD61151: upd61151_s_std [ 76.468155] set standart to 255 [ 76.940008] DEBUG uPD61151: upd61151_s_std [ 76.940061] set standart to 255 [ 76.940109] DEBUG uPD61151: upd61151_s_std [ 76.940157] set standart to 255
/*
*
* Device driver for philips saa7134 based TV cards
* SPI software interface support
*
* (c) 2009 Beholder Intl. Ltd. Dmitry Belimov <[email protected]> *
* Important: now support ONLY SPI_MODE_0, see FIXME
*
* This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation; either version 2 of the License, or * (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*/
#include "saa7134-reg.h"
#include "saa7134.h"
#include <media/v4l2-common.h>
/* ----------------------------------------------------------- */
static unsigned int spi_debug; module_param(spi_debug, int, 0644); MODULE_PARM_DESC(spi_debug,"enable debug messages [spi]");
#define d1printk if (1 == spi_debug) printk
#define d2printk if (2 == spi_debug) printk
static inline void spidelay(unsigned d)
{
ndelay(d);
}static inline struct saa7134_spi_gpio *to_sb(struct spi_device *spi)
{
return spi_master_get_devdata(spi->master);
}static inline void setsck(struct spi_device *dev, int on)
{
struct saa7134_spi_gpio *sb = to_sb(dev);
saa7134_set_gpio(sb->controller_data, sb->controller_data->spi.clock, on ? 1 : 0);
}static inline void setmosi(struct spi_device *dev, int on)
{
struct saa7134_spi_gpio *sb = to_sb(dev);
saa7134_set_gpio(sb->controller_data, sb->controller_data->spi.mosi, on ? 1 : 0);
}static inline u32 getmiso(struct spi_device *dev)
{
struct saa7134_spi_gpio *sb = to_sb(dev);
unsigned long status;
status = saa7134_get_gpio(sb->controller_data);
if ( status & (1 << sb->controller_data->spi.miso))
return 1;
else
return 0;
}#define EXPAND_BITBANG_TXRX 1
#include <linux/spi/spi_bitbang.h>
static void saa7134_spi_gpio_chipsel(struct spi_device *dev, int on)
{
struct saa7134_spi_gpio *sb = to_sb(dev);
if (on)
{
/* FIXME: set clock to zero by default, only SPI_MODE_0 compatible */
saa7134_set_gpio(sb->controller_data, sb->controller_data->spi.clock, 0);
saa7134_set_gpio(sb->controller_data, sb->controller_data->spi.cs, 0);
}
else
saa7134_set_gpio(sb->controller_data, sb->controller_data->spi.cs, 1);
}/* Our actual bitbanger routine. */
static u32 saa7134_txrx(struct spi_device *spi, unsigned nsecs, u32 word, u8 bits)
{
return bitbang_txrx_be_cpha0(spi, nsecs, 0, word, bits);
}int saa7134_spi_register(struct saa7134_dev *dev, struct spi_board_info *info)
{
struct spi_master *master = NULL;
struct saa7134_spi_gpio *sb = NULL;
int ret = 0;
master = spi_alloc_master(&dev->pci->dev, sizeof(struct saa7134_spi_gpio));
if (master == NULL)
{
dev_err(&dev->pci->dev, "failed to allocate spi master\n");
ret = -ENOMEM;
goto err;
}
sb = spi_master_get_devdata(master);
master->num_chipselect = dev->spi.num_chipselect;
master->bus_num = -1;
sb->master = spi_master_get(master);
sb->bitbang.master = sb->master;
sb->bitbang.master->bus_num = -1;
sb->bitbang.master->num_chipselect = dev->spi.num_chipselect;
sb->bitbang.chipselect = saa7134_spi_gpio_chipsel;
sb->bitbang.txrx_word[SPI_MODE_0] = saa7134_txrx;
/* set state of spi pins */
saa7134_set_gpio(dev, dev->spi.cs, 1);
/* FIXME: set clock to zero by default, only SPI_MODE_0 compatible */
saa7134_set_gpio(dev, dev->spi.clock, 0);
saa7134_set_gpio(dev, dev->spi.mosi, 1);
saa7134_set_gpio(dev, dev->spi.miso, 3);
/* start SPI bitbang master */
ret = spi_bitbang_start(&sb->bitbang);
if (ret) {
dev_err(&dev->pci->dev, "Failed to register SPI master\n");
goto err_no_bitbang;
}
dev_info(&dev->pci->dev,
"spi master registered: bus_num=%d num_chipselect=%d\n",
master->bus_num, master->num_chipselect);
sb->controller_data = dev;
info->bus_num = sb->master->bus_num;
info->controller_data = master;
dev->spi_adap = master;err_no_bitbang:
spi_master_put(master); err: return ret; }
int saa7134_spi_unregister(struct saa7134_dev *dev)
{
struct saa7134_spi_gpio *sb = spi_master_get_devdata(dev->spi_adap);
spi_bitbang_stop(&sb->bitbang);
spi_master_put(sb->master);
return 0;
}/*
* Overrides for Emacs so that we follow Linus's tabbing style.
* ---------------------------------------------------------------------------
* Local variables:
* c-basic-offset: 8
* End:
*/
/*
upd61151 - driver for the uPD61151 by NEC
Copyright (C) Beholder Intl. Ltd. Dmitry Belimov <[email protected]>
Based on the saa6752s.c driver.
Copyright (C) 2004 Andrew de Quincey
This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License vs published by the Free Software Foundation; either version 2 of the License, or (at your option) any later version.
This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details.
You should have received a copy of the GNU General Public License along with this program; if not, write to the Free Software Foundation, Inc., 675 Mvss Ave, Cambridge, MA 02139, USA.
*/
#include <linux/init.h>
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/device.h>
#include <linux/sysfs.h>
#include <linux/string.h>
#include <linux/timer.h>
#include <linux/delay.h>
#include <linux/errno.h>
#include <linux/slab.h>
#include <linux/poll.h>
#include <linux/spi/spi.h>
#include <linux/types.h>
#include "compat.h"
#include <linux/videodev2.h>
#include <media/v4l2-device.h>
#include <media/v4l2-common.h>
#include <media/v4l2-chip-ident.h>
#include <media/upd61151.h>
#include <linux/crc32.h>
#include "saa7134.h"
#define MPEG_VIDEO_TARGET_BITRATE_MAX 27000 #define MPEG_VIDEO_MAX_BITRATE_MAX 27000 #define MPEG_TOTAL_TARGET_BITRATE_MAX 27000
#define MPEG_PID_MAX ((1 << 14) - 1)
#define DRVNAME "upd61151"
static unsigned int spi_debug; module_param(spi_debug, int, 0644); MODULE_PARM_DESC(spi_debug,"enable debug messages [spi]");
#define d1printk_spi if (1 <= spi_debug) printk
#define d2printk_spi if (2 <= spi_debug) printk
static unsigned int core_debug; module_param(core_debug, int, 0644); MODULE_PARM_DESC(core_debug,"enable debug messages [core]");
#define d1printk_core if (1 <= core_debug) printk
#define d2printk_core if (2 <= core_debug) printk
MODULE_DESCRIPTION("device driver for uPD61151 MPEG2 encoder"); MODULE_AUTHOR("Dmitry V Belimov"); MODULE_LICENSE("GPL");
/* Result codes */
#define RESULT_SUCCESS 0 #define RESULT_FAILURE 1 #define STATUS_DEVICE_NOT_READY 2 #define STATUS_DEVICE_DATA_ERROR 3
enum upd61151_videoformat {
UPD61151_VF_D1 = 0, /* 720x480/720x576 */
UPD61151_VF_D2 = 1, /* 704x480/704x576 */
UPD61151_VF_D3 = 2, /* 352x480/352x576 */
UPD61151_VF_D4 = 3, /* 352x240/352x288 */
UPD61151_VF_D5 = 4, /* 544x480/544x576 */
UPD61151_VF_D6 = 5, /* 480x480/480x576 */
UPD61151_VF_D7 = 6, /* 352x240/352x288 */
UPD61151_VF_D8 = 8, /* 640x480/640x576 */
UPD61151_VF_D9 = 9, /* 320x480/320x576 */
UPD61151_VF_D10 = 10, /* 320x240/320x288 */
UPD61151_VF_UNKNOWN,
};struct upd61151_mpeg_params {
/* transport streams */
__u16 ts_pid_pmt;
__u16 ts_pid_audio;
__u16 ts_pid_video;
__u16 ts_pid_pcr;
/* audio */
enum v4l2_mpeg_audio_encoding au_encoding;
enum v4l2_mpeg_audio_l2_bitrate au_l2_bitrate;
/* video */
enum v4l2_mpeg_video_aspect vi_aspect;
enum v4l2_mpeg_video_bitrate_mode vi_bitrate_mode;
__u32 vi_bitrate;
__u32 vi_bitrate_peak;
};static const struct v4l2_format v4l2_format_table[] =
{
[UPD61151_VF_D1] =
{ .fmt = { .pix = { .width = 720, .height = 576 }}},
[UPD61151_VF_D2] =
{ .fmt = { .pix = { .width = 704, .height = 576 }}},
[UPD61151_VF_D3] =
{ .fmt = { .pix = { .width = 352, .height = 576 }}},
[UPD61151_VF_D4] =
{ .fmt = { .pix = { .width = 352, .height = 288 }}},
[UPD61151_VF_D5] =
{ .fmt = { .pix = { .width = 544, .height = 576 }}},
[UPD61151_VF_D6] =
{ .fmt = { .pix = { .width = 480, .height = 576 }}},
[UPD61151_VF_D7] =
{ .fmt = { .pix = { .width = 352, .height = 288 }}},
[UPD61151_VF_D8] =
{ .fmt = { .pix = { .width = 640, .height = 576 }}},
[UPD61151_VF_D9] =
{ .fmt = { .pix = { .width = 320, .height = 576 }}},
[UPD61151_VF_D10] =
{ .fmt = { .pix = { .width = 320, .height = 288 }}},
[UPD61151_VF_UNKNOWN] =
{ .fmt = { .pix = { .width = 0, .height = 0}}},
};struct upd61151_state {
struct v4l2_subdev sd;
struct upd61151_mpeg_params params;
enum upd61151_videoformat video_format;
v4l2_std_id standard;
enum upd61151_encode_state enstate;
};static struct upd61151_mpeg_params param_defaults =
{
.ts_pid_pmt = 16,
.ts_pid_video = 260,
.ts_pid_audio = 256,
.ts_pid_pcr = 259,
.vi_aspect = V4L2_MPEG_VIDEO_ASPECT_4x3,
.vi_bitrate = 4000,
.vi_bitrate_peak = 6000,
.vi_bitrate_mode = V4L2_MPEG_VIDEO_BITRATE_MODE_VBR,
.au_encoding = V4L2_MPEG_AUDIO_ENCODING_LAYER_2,
.au_l2_bitrate = V4L2_MPEG_AUDIO_L2_BITRATE_256K,
};static int write_reg(struct spi_device *spi, u8 address, u8 data)
{
u8 buf[2];
buf[0] = ((address >> 2) << 2);
buf[1] = data;
d2printk_spi(KERN_DEBUG "%s: spi data 0x%x <= 0x%x\n",spi->modalias,address,data);
return spi_write(spi, buf, ARRAY_SIZE(buf));
}static void write_fw(struct spi_device *spi, u8 address, const struct firmware *fw)
{
u8 buf[2];
u32 i;
buf[0] = ((address >> 2) << 2);
for (i=0; i < fw->size; i++)
{
buf[1] = *(fw->data+i);
spi_write(spi, buf, 2);
}
}static int read_reg(struct spi_device *spi, unsigned char address, unsigned char *data)
{
u8 buf[1];
int ret;
ret = 0;
buf[0] = ((address >> 2) << 2) | 0x02;
ret = spi_write_then_read(spi, buf, 1, data, 1);
d2printk_spi(KERN_DEBUG "%s: spi data 0x%x => 0x%x, status %d\n",spi->modalias, address, *data, ret);
return ret;
}static u8 upd61151_get_state(struct spi_device *spi)
{
u8 rbyte = 0x00;
read_reg(spi, UPD61151_STATUS, &rbyte);
d2printk_core(KERN_DEBUG "%s: MPEG2 core status %d\n", spi->modalias, rbyte & 0x07);
return rbyte & 0x07;
}static int upd61151_set_state(struct v4l2_subdev *sd, enum upd61151_config nstate) {
printk("upd61151_set_state\n");
return RESULT_SUCCESS;
}static void upd61151_reset_core(struct spi_device *spi)
{
write_reg(spi, UPD61151_SOFTWARE_RST, 0x01);
}static void upd61151_set_dest_addr(struct spi_device *spi, u32 addr)
{
write_reg(spi, UPD61151_TRANSFER_ADDR1, (u8)((addr >> 16) & 0xFF));
write_reg(spi, UPD61151_TRANSFER_ADDR2, (u8)((addr >> 8) & 0xFF));
write_reg(spi, UPD61151_TRANSFER_ADDR3, (u8)(addr & 0xFF));
}static void upd61151_set_data_size(struct spi_device *spi, u32 dsize)
{
write_reg(spi, UPD61151_DATA_COUNTER1, (u8)((dsize >> 16) & 0xFF));
write_reg(spi, UPD61151_DATA_COUNTER2, (u8)((dsize >> 8) & 0xFF));
write_reg(spi, UPD61151_DATA_COUNTER3, (u8)(dsize & 0xFF));
}static u8 upd61151_clear_transfer_irq(struct spi_device *spi)
{
u8 rbyte = 0x00;
read_reg(spi, UPD61151_TRANSFER_IRQ, &rbyte);
d2printk_core(KERN_DEBUG "%s: Transfer IRQ status 0x%x\n", spi->modalias, rbyte);
if (rbyte)
write_reg(spi, UPD61151_IRQ, rbyte);
return rbyte;
}static void upd61151_handle_transfer_err(struct spi_device *spi)
{
u8 rbyte;
printk("upd61151_handle_transfer_err\n");
/* Set data transfer count size = 1 */
upd61151_set_data_size(spi, 0x01);
/* Set transfer mode SDRAM -> Host */
write_reg(spi, UPD61151_TRANSFER_MODE, 0x01);
/* Read one byte from SDRAM */
read_reg(spi, UPD61151_TRANSFER_DATA, &rbyte);
/* Release transfer mode */
write_reg(spi, UPD61151_TRANSFER_MODE, 0x00);
/* Clear IRQ */
upd61151_clear_transfer_irq(spi);
/* Set destination address to 0x000000 */
upd61151_set_dest_addr(spi, 0x000000);
/* Set data transfer count size = 3 */
upd61151_set_data_size(spi, 0x03);
/* Set transfer mode SDRAM -> Host */
write_reg(spi, UPD61151_TRANSFER_MODE, 0x01);
/* Clear IRQ */
upd61151_clear_transfer_irq(spi);
/* Read 3 byte from SDRAM */
read_reg(spi, UPD61151_TRANSFER_DATA, &rbyte);
read_reg(spi, UPD61151_TRANSFER_DATA, &rbyte);
read_reg(spi, UPD61151_TRANSFER_DATA, &rbyte);
/* Clear IRQ */
upd61151_clear_transfer_irq(spi);
/* Set transfer mode SDRAM -> Host */
write_reg(spi, UPD61151_TRANSFER_MODE, 0x00);
/* Clear IRQ */
upd61151_clear_transfer_irq(spi);
}static int upd61151_wait_transfer_irq(struct spi_device *spi)
{
u8 i, rstatus;
rstatus = 0;
/* Wait transfer interrupt */
for (i=0; i<5; i++)
{
rstatus = upd61151_clear_transfer_irq(spi);
if (rstatus)
break;
msleep(1);
}
if (!rstatus)
return STATUS_DEVICE_NOT_READY;
if (rstatus & 0x04)
{
/* Data transfer error */
upd61151_handle_transfer_err(spi);
return STATUS_DEVICE_DATA_ERROR;
}
return RESULT_SUCCESS;
}static u8 upd61151_clear_info_irq(struct spi_device *spi)
{
u8 rbyte = 0x00;
read_reg(spi, UPD61151_IRQ, &rbyte);
d2printk_core(KERN_DEBUG "%s: IRQ status 0x%x\n", spi->modalias, rbyte);
if (rbyte)
write_reg(spi, UPD61151_IRQ, rbyte);
return rbyte;
}static u8 upd61151_clear_error_irq(struct spi_device *spi)
{
u8 rbyte = 0x00;
read_reg(spi, UPD61151_ERROR_IRQ, &rbyte);
d2printk_core(KERN_DEBUG "%s: IRQ error status 0x%x\n", spi->modalias, rbyte);
if (rbyte)
write_reg(spi, UPD61151_ERROR_IRQ, rbyte);
return rbyte;
}static u8 upd61151_clear_except_irq(struct spi_device *spi)
{
u8 rbyte = 0x00;
read_reg(spi, UPD61151_EXCEPT_IRQ, &rbyte);
d2printk_core(KERN_DEBUG "%s: IRQ exception status 0x%x\n", spi->modalias, rbyte);
if (rbyte)
write_reg(spi, UPD61151_EXCEPT_IRQ, rbyte);
return rbyte;
}static int upd61151_load_base_firmware(struct v4l2_subdev *sd)
{
struct spi_device *spi = v4l2_get_subdevdata(sd);
u32 size;
const struct firmware *fw;
int ret = RESULT_SUCCESS;printk("DEBUG: upd61151_load_base_firmware\n");
size = UPD61151_DEFAULT_PS_FIRMWARE_SIZE / 4;
/* request the firmware, this will block and timeout */
printk(KERN_INFO "%s: waiting for base firmware upload (%s)...\n",
spi->modalias, UPD61151_DEFAULT_PS_FIRMWARE);
ret = request_firmware(&fw, UPD61151_DEFAULT_PS_FIRMWARE,
spi->dev.parent);
if (ret)
{
printk(KERN_ERR "%s: Upload failed. (file not found?)\n",spi->modalias);
ret = RESULT_FAILURE;
goto out;
}
else
printk(KERN_DEBUG "%s: firmware read %Zu bytes.\n", spi->modalias,
fw->size);
if (fw->size != UPD61151_DEFAULT_PS_FIRMWARE_SIZE)
{
printk(KERN_ERR "%s: firmware incorrect size\n", spi->modalias);
ret = RESULT_FAILURE;
goto out;
}
printk(KERN_INFO "%s: base firmware uploading...\n", spi->modalias);
upd61151_clear_transfer_irq(spi);
/* CPU reset ON */
write_reg(spi, UPD61151_SOFTWARE_RST, 0x02);
/* Set destination address to 0x000000 */
upd61151_set_dest_addr(spi, 0x000000);
/* Set transfer data count to firmware size / 4 */
upd61151_set_data_size(spi, size);
/* Set transfer mode to Host -> iRAM */
write_reg(spi, UPD61151_TRANSFER_MODE, 0x80);
printk("fw upload start\n");
write_fw(spi, UPD61151_TRANSFER_DATA, fw);printk("fw upload stop\n");
if (upd61151_wait_transfer_irq(spi) == RESULT_SUCCESS)
{
/* Release transfer mode */
write_reg(spi, UPD61151_TRANSFER_MODE, 0x00);
printk(KERN_INFO "%s: base firmware upload complete...\n", spi->modalias);
}
else
printk(KERN_INFO "%s: base firmware upload FAIL...\n", spi->modalias);out:
/* CPU reset OFF */ write_reg(spi, UPD61151_SOFTWARE_RST, 0x00); release_firmware(fw); return ret; }
static int upd61151_load_audio_firmware(struct v4l2_subdev *sd)
{
struct spi_device *spi = v4l2_get_subdevdata(sd);
const struct firmware *fw;
u32 addr, i;
int ret = RESULT_SUCCESS;printk("DEBUG: upd61151_load_audio_firmware\n");
/* request the firmware, this will block and timeout */
printk(KERN_INFO "%s: waiting for audio firmware upload (%s)...\n",
spi->modalias, UPD61151_DEFAULT_AUDIO_FIRMWARE);
ret = request_firmware(&fw, UPD61151_DEFAULT_AUDIO_FIRMWARE,
spi->dev.parent);
if (ret)
{
printk(KERN_ERR "%s: Upload failed. (file not found?)\n",spi->modalias);
ret = RESULT_FAILURE;
goto out;
}
else
printk(KERN_DEBUG "%s: firmware read %Zu bytes.\n", spi->modalias,
fw->size);
if (fw->size != UPD61151_DEFAULT_AUDIO_FIRMWARE_SIZE)
{
printk(KERN_ERR "%s: firmware incorrect size\n", spi->modalias);
ret = RESULT_FAILURE;
goto out;
}
printk(KERN_INFO "%s: audio firmware uploading...\n", spi->modalias);
addr = 0x308F00;
addr >>= 5;
upd61151_clear_transfer_irq(spi);
/* Set destination address */
upd61151_set_dest_addr(spi, addr);
/* Set transfer data count to firmware size */
upd61151_set_data_size(spi, UPD61151_DEFAULT_AUDIO_FIRMWARE_SIZE);
/* Set transfer mode to Host -> SDRAM */
write_reg(spi, UPD61151_TRANSFER_MODE, 0x02);printk("fw upload start\n");
for (i = 0; i < UPD61151_DEFAULT_AUDIO_FIRMWARE_SIZE; i++)
{
write_reg(spi, UPD61151_TRANSFER_DATA, *(fw->data+i));
/* Check Transfer interrupt each 128 bytes */
if ( ((i+1) % 128) ==0 )
{
ret = upd61151_wait_transfer_irq(spi);
if (ret != RESULT_SUCCESS)
break;
}
}printk("fw upload stop\n");
if (ret == RESULT_SUCCESS)
{
/* Release transfer mode */
write_reg(spi, UPD61151_TRANSFER_MODE, 0x00);
printk(KERN_INFO "%s: audio firmware upload complete...\n", spi->modalias);
}
else
printk(KERN_INFO "%s: audio firmware upload FAIL...\n", spi->modalias);out:
release_firmware(fw); return ret; }
static int upd61151_chip_command(struct spi_device *spi, enum upd61151_command command)
{
u8 cycles, wait, i, irqerr;
enum upd61151_command want_state;printk("DEBUG uPD61151: upd61151_chip_command\n");
/* calculate delay */
cycles = 100;
wait = 10;
switch (command)
{
case UPD61151_COMMAND_STANDBY_STOP:
case UPD61151_COMMAND_PAUSE:
break;
case UPD61151_COMMAND_START_RESTART:
cycles = 200;
wait = 1;
break;
default:
return RESULT_FAILURE;
}
/* Clear IRQ */
upd61151_clear_error_irq(spi);
write_reg(spi, UPD61151_COMMAND, command);
for (i=0; i < cycles; i++)
{
/* Check state */
want_state = upd61151_get_state(spi);
if (want_state == command)
{
upd61151_clear_info_irq(spi);
d2printk_core(KERN_DEBUG "%s: SetState %d SUCCESS, delay [%d ms].\n", spi->modalias, want_state, i*wait);
return RESULT_SUCCESS;
}
/* Check error interrupt */
irqerr = upd61151_clear_error_irq(spi);
if (irqerr & 0x01)
{
d2printk_core(KERN_DEBUG "%s: SetState %d FAIL, Invalid Command (IC).\n", spi->modalias, command);
break;
}
if (irqerr & 0x02)
{
d2printk_core(KERN_DEBUG "%s: SetState %d FAIL, Invalid Parameter (IP).\n", spi->modalias, command);
break;
}
if (irqerr & 0x04)
{
d2printk_core(KERN_DEBUG "%s: SetState %d FAIL, Invalid Audio Firmware Download (IADL).\n", spi->modalias, command);
break;
}
if (irqerr & 0x08)
{
d2printk_core(KERN_DEBUG "%s: SetState %d FAIL, Invalid System Bit Rate (ISBR).\n", spi->modalias, command);
break;
}
msleep(wait);
}
if (i >= cycles)
{
d2printk_core(KERN_DEBUG "%s: SetState %d FAIL, TIMEOUT [%d ms].\n", spi->modalias, command, cycles*wait);
}
return RESULT_FAILURE;
}static int upd61151_setup_video_frontend(struct v4l2_subdev *sd)
{
struct spi_device *spi = v4l2_get_subdevdata(sd);
struct upd61151_state *h = spi_get_drvdata(spi);
int ret = RESULT_SUCCESS;
u8 dbyte;printk("upd61151_setup_video_frontend\n");
dbyte = 0x00;
printk("dbyte = 0x%x ",dbyte);
/* Update FIDT */
if (h->standard & V4L2_STD_625_50)
dbyte |= 0x10;
printk(" 0x%x ",dbyte);
dbyte |= h->video_format;
printk(" 0x%x \n",dbyte);
write_reg(spi, UPD61151_VIDEO_ATTRIBUTE, dbyte);
/* SAV/EAV (ITU-656), FID not inverted */
write_reg(spi, UPD61151_VIDEO_SYNC, 0x80);
/* Set H offset */
write_reg(spi, UPD61151_VIDEO_HOFFSET, 0x00);
/* Set V offset */
if (h->standard & V4L2_STD_625_50)
dbyte = 0x01;
else
dbyte = 0x03;
write_reg(spi, UPD61151_VIDEO_VOFFSET, dbyte);
/* Setup VBI */
/* SLCEN = 0, VBIOFFV = 4, VBIOFFH = 8*/
write_reg(spi, UPD61151_VBI_ADJ1, 0x48);
return ret;
}static int upd61151_setup_audio_frontend(struct v4l2_subdev *sd)
{
struct spi_device *spi = v4l2_get_subdevdata(sd);
struct upd61151_state *h = spi_get_drvdata(spi);
int ret = RESULT_SUCCESS;
u8 dbyte;printk("upd61151_setup_audio_frontend\n");
//UPD61151_AUDIO_ATTRIBUTE1
return ret; }
static int upd61151_config_encoder(struct v4l2_subdev *sd) {
printk("upd61151_config_encoder\n");
return RESULT_SUCCESS;
}static int upd61151_download_firmware(struct v4l2_subdev *sd)
{
struct spi_device *spi = v4l2_get_subdevdata(sd);
struct upd61151_state *h = spi_get_drvdata(spi);printk("DEBUG: upd61151_download_firmware\n");
h->enstate = UPD61151_ENCODE_STATE_IDLE;
upd61151_reset_core(spi);
udelay(1);
/* Init SDRAM */
write_reg(spi, UPD61151_SDRAM_IF_DELAY_ADJ, 0x01);
write_reg(spi, UPD61151_SDRAM_FCLK_SEL, 0xA0);
udelay(200);
/* Set SDRAM to STANDBY */
write_reg(spi, UPD61151_SDRAM_STANDBY, 0x01);
udelay(10);
/* Release SDRAM from STANDBY */
write_reg(spi, UPD61151_SDRAM_STANDBY, 0x00);
if (upd61151_load_base_firmware(sd))
return RESULT_FAILURE;
if (upd61151_load_audio_firmware(sd))
return RESULT_FAILURE;
/* Clear IRQ flags */
if ( !(upd61151_clear_info_irq(spi) & 0x10) )
{
/* INICM not running */
d1printk_core(KERN_DEBUG "%s: download firmware FAILED. INICM is not run.\n", spi->modalias);
return RESULT_FAILURE;
}
/* Set STANDBY state */
if (upd61151_chip_command(spi, UPD61151_COMMAND_STANDBY_STOP))
return RESULT_FAILURE;
/* Setup video input frontend */
upd61151_setup_video_frontend(sd);
/* Setup audio input frontend */
upd61151_setup_audio_frontend(sd);
/* Config encoder params */
upd61151_config_encoder(sd);
/* Set all config and upload audio firmware */
if (upd61151_set_state(sd, UPD61151_CONFIG_ALL))
return RESULT_FAILURE;
/* Return to STANDBY state */
if (upd61151_chip_command(spi, UPD61151_COMMAND_STANDBY_STOP))
return RESULT_FAILURE;
return RESULT_SUCCESS;
}static int upd61151_is_need_reload_fw(struct spi_device *spi)
{
if (upd61151_get_state(spi) == UPD61151_COMMAND_INITIAL)
{
d1printk_core(KERN_DEBUG "%s: need reload firmware\n", spi->modalias);
return 1;
}
if (upd61151_clear_except_irq(spi) & 0x04)
{
d1printk_core(KERN_DEBUG "%s: mainly buffer of encoder is overflowed\n", spi->modalias);
return 1;
}
return 0;
}#if 0
static int upd61151_set_bitrate(struct spi_device *spi,
struct upd61151_state *h)
{
printk("DEBUG uPD61151: upd61151_set_bitrate\n");
return RESULT_SUCCESS;
}#endif
static int upd61151_queryctrl(struct v4l2_subdev *sd, struct v4l2_queryctrl *qctrl) {
printk("DEBUG uPD61151: upd61151_queryctrl\n");
return RESULT_SUCCESS;
}static int upd61151_querymenu(struct v4l2_subdev *sd, struct v4l2_querymenu *qmenu) {
printk("DEBUG uPD61151: upd61151_querymenu\n");
return RESULT_SUCCESS;
}static int upd61151_init(struct v4l2_subdev *sd, u32 flags) {
printk("DEBUG uPD61151: upd61151_init\n");
return RESULT_SUCCESS;
}static int upd61151_do_ext_ctrls(struct v4l2_subdev *sd, struct v4l2_ext_controls *ctrls, int set) {
printk("DEBUG uPD61151: upd61151_do_ext_ctrls\n");
return RESULT_SUCCESS;
}static int upd61151_s_ext_ctrls(struct v4l2_subdev *sd, struct v4l2_ext_controls *ctrls) {
printk("DEBUG uPD61151: upd61151_s_ext_ctrls\n");
return upd61151_do_ext_ctrls(sd, ctrls, 1);
}static int upd61151_try_ext_ctrls(struct v4l2_subdev *sd, struct v4l2_ext_controls *ctrls) {
printk("DEBUG uPD61151: upd61151_s_ext_ctrls\n");
return upd61151_do_ext_ctrls(sd, ctrls, 0);
}static int upd61151_g_ext_ctrls(struct v4l2_subdev *sd, struct v4l2_ext_controls *ctrls) {
printk("DEBUG uPD61151: upd61151_g_ext_ctrls\n");
return RESULT_SUCCESS;
}static int upd61151_g_fmt(struct v4l2_subdev *sd, struct v4l2_format *f)
{
struct spi_device *spi = v4l2_get_subdevdata(sd);
struct upd61151_state *h = spi_get_drvdata(spi);
if (h->video_format == UPD61151_VF_UNKNOWN)
h->video_format = UPD61151_VF_D1;
f->fmt.pix.width =
v4l2_format_table[h->video_format].fmt.pix.width;
f->fmt.pix.height =
v4l2_format_table[h->video_format].fmt.pix.height;printk("DEBUG uPD61151: upd61151_g_fmt\n");
return 0;
}static int upd61151_s_fmt(struct v4l2_subdev *sd, struct v4l2_format *f) {
printk("DEBUG uPD61151: upd61151_s_fmt\n");
return RESULT_SUCCESS;
}static int upd61151_s_std(struct v4l2_subdev *sd, v4l2_std_id std)
{
struct spi_device *spi = v4l2_get_subdevdata(sd);
struct upd61151_state *h = spi_get_drvdata(spi);
printk("DEBUG uPD61151: upd61151_s_std\n");
h->standard = std;
return 0;
}static int upd61151_g_chip_ident(struct v4l2_subdev *sd, struct v4l2_dbg_chip_ident *chip) {
printk("DEBUG uPD61151: upd61151_g_chip_ident\n");
return RESULT_SUCCESS;
}/* ----------------------------------------------------------------------- */
static const struct v4l2_subdev_core_ops upd61151_core_ops = {
.g_chip_ident = upd61151_g_chip_ident,
.init = upd61151_init,
.queryctrl = upd61151_queryctrl,
.querymenu = upd61151_querymenu,
.g_ext_ctrls = upd61151_g_ext_ctrls,
.s_ext_ctrls = upd61151_s_ext_ctrls,
.try_ext_ctrls = upd61151_try_ext_ctrls,
.s_std = upd61151_s_std,
};static const struct v4l2_subdev_video_ops upd61151_video_ops = {
.s_fmt = upd61151_s_fmt,
.g_fmt = upd61151_g_fmt,
};static const struct v4l2_subdev_ops upd61151_ops = {
.core = &upd61151_core_ops,
.video = &upd61151_video_ops,
};static int __devinit upd61151_probe(struct spi_device *spi)
{
struct upd61151_state *h = kzalloc(sizeof(*h), GFP_KERNEL);
struct v4l2_subdev *sd;printk("upd61151_probe function\n");
if (h == NULL) return -ENOMEM; sd = &h->sd; v4l2_spi_subdev_init(sd, spi, &upd61151_ops); spi_set_drvdata(spi, h);
/* function for detect a chip here */
// h->chip = upd61151_detect(h);
if (upd61151_is_need_reload_fw(spi))
{
printk("Start load firmware...\n");
if (!upd61151_download_firmware(sd))
printk("Firmware downloaded SUCCESS!!!\n");
else
printk("Firmware downloaded FAIL!!!\n");
}
else
printk("Firmware is OK\n");
h->params = param_defaults;
h->standard = 0; /* Assume 625 input lines */
return 0;
}static int __devexit upd61151_remove(struct spi_device *spi)
{
struct upd61151_state *h = spi_get_drvdata(spi);
printk("upd61151_remove function\n");
v4l2_device_unregister_subdev(&h->sd);
// kfree(&h->sd);
kfree(h);
spi_unregister_device(spi);
return 0;
}static struct spi_driver upd61151_driver = {
.driver = {
.name = DRVNAME,
.bus = &spi_bus_type,
.owner = THIS_MODULE,
},
.probe = upd61151_probe,
.remove = __devexit_p(upd61151_remove),
};static int __init init_upd61151(void)
{
return spi_register_driver(&upd61151_driver);
}module_init(init_upd61151);
static void __exit exit_upd61151(void)
{
spi_unregister_driver(&upd61151_driver);
}module_exit(exit_upd61151);
/*
* Overrides for Emacs so that we follow Linus's tabbing style.
* ---------------------------------------------------------------------------
* Local variables:
* c-basic-offset: 8
* End:
*/
/*
upd61151.h - definition for NEC uPD61151 MPEG encoder
Copyright (C) Beholder Intl. Ltd. Dmitry Belimov <[email protected]>
This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation; either version 2 of the License, or (at your option) any later version.
This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details.
You should have received a copy of the GNU General Public License along with this program; if not, write to the Free Software Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*/
#include <linux/firmware.h>
#define UPD61151_DEFAULT_PS_FIRMWARE "D61151_PS_7133_v22_031031.bin" #define UPD61151_DEFAULT_PS_FIRMWARE_SIZE 97002
#define UPD61151_DEFAULT_AUDIO_FIRMWARE "audrey_MPE_V1r51.bin" #define UPD61151_DEFAULT_AUDIO_FIRMWARE_SIZE 40064
/* FIXME START: OLD FROM SAA6752HS */
enum mpeg_video_bitrate_mode {
MPEG_VIDEO_BITRATE_MODE_VBR = 0, /* Variable bitrate */ MPEG_VIDEO_BITRATE_MODE_CBR = 1, /* Constant bitrate */
MPEG_VIDEO_BITRATE_MODE_MAX
};
enum mpeg_audio_bitrate {
MPEG_AUDIO_BITRATE_256 = 0, /* 256 kBit/sec */
MPEG_AUDIO_BITRATE_384 = 1, /* 384 kBit/sec */
MPEG_AUDIO_BITRATE_MAX
};enum mpeg_video_format {
MPEG_VIDEO_FORMAT_D1 = 0,
MPEG_VIDEO_FORMAT_2_3_D1 = 1,
MPEG_VIDEO_FORMAT_1_2_D1 = 2,
MPEG_VIDEO_FORMAT_SIF = 3,
MPEG_VIDEO_FORMAT_MAX
};#define MPEG_VIDEO_TARGET_BITRATE_MAX 27000
#define MPEG_VIDEO_MAX_BITRATE_MAX 27000
#define MPEG_TOTAL_BITRATE_MAX 27000
#define MPEG_PID_MAX ((1 << 14) - 1)
struct mpeg_params {
enum mpeg_video_bitrate_mode video_bitrate_mode;
unsigned int video_target_bitrate;
unsigned int video_max_bitrate; // only used for VBR
enum mpeg_audio_bitrate audio_bitrate;
unsigned int total_bitrate;
unsigned int pmt_pid;
unsigned int video_pid;
unsigned int audio_pid;
unsigned int pcr_pid;
enum mpeg_video_format video_format;
};/* FIXME STOP: OLD FROM SAA6752HS */
enum upd61151_command {
UPD61151_COMMAND_INITIAL = 0,
UPD61151_COMMAND_STANDBY_STOP = 1,
UPD61151_COMMAND_CONFIG = 2,
UPD61151_COMMAND_START_RESTART = 3,
UPD61151_COMMAND_PAUSE = 4,
UPD61151_COMMAND_CHANGE = 5,
};enum upd61151_encode_state {
UPD61151_ENCODE_STATE_IDLE = 0,
UPD61151_ENCODE_STATE_ENCODE = 1,
UPD61151_ENCODE_STATE_PAUSE = 2,
};enum upd61151_config {
UPD61151_CONFIG_ALL = 0x00,
UPD61151_CONFIG_AUDIO_FW = 0x10,
UPD61151_CONFIG_VIDEO_INPUT = 0x20,
UPD61151_CONFIG_VBI_INPUT = 0x30,
UPD61151_CONFIG_AUDIO_INPUT = 0x40,
};#define UPD61151_COMMAND 0x00 #define UPD61151_STATUS 0x04 #define UPD61151_VIDEO_ATTRIBUTE 0x1C #define UPD61151_AUDIO_ATTRIBUTE1 0x2C #define UPD61151_VIDEO_SYNC 0x54 #define UPD61151_VIDEO_HOFFSET 0x58 #define UPD61151_VIDEO_VOFFSET 0x5C #define UPD61151_VBI_ADJ1 0x74 #define UPD61151_VBI_ADJ2 0x78 #define UPD61151_TRANSFER_MODE 0x80 #define UPD61151_TRANSFER_ADDR1 0x90 #define UPD61151_TRANSFER_ADDR2 0x94 #define UPD61151_TRANSFER_ADDR3 0x98 #define UPD61151_DATA_COUNTER1 0x9C #define UPD61151_DATA_COUNTER2 0xA0 #define UPD61151_DATA_COUNTER3 0xA4 #define UPD61151_TRANSFER_IRQ 0xC0 #define UPD61151_IRQ 0xC4 #define UPD61151_ERROR_IRQ 0xCC #define UPD61151_EXCEPT_IRQ 0xD0 #define UPD61151_SDRAM_IF_DELAY_ADJ 0xDC #define UPD61151_SDRAM_FCLK_SEL 0xE0 #define UPD61151_SDRAM_STANDBY 0xE8 #define UPD61151_SOFTWARE_RST 0xF8 #define UPD61151_TRANSFER_DATA 0xFC
/*
* Local variables:
* c-basic-offset: 8
* End:
*/
Quoted 7 lines · On Tuesday 09 February 2010 06:41:50 Dmitri Belimov wrote:
Hi Hans
This is my last state for review.
After small time I'll finish process of initialize the encoder. Configure some register, upload two firmware for video and for audio. Configure the frontends.
Quoted 7 lines
I have the questions.
For configuring audio frontend need know samplerate of audio. saa7134 can only 32kHz
saa7131/3/5 on I2S 32кГц from SIF source and 32/44.1/48 from external i.e. RCA stereo audio input.Hardcode 32kHz or need a function for determine mode of audio??
See struct v4l2_subdev_audio_ops: it has a s_clock_freq op for precisely that purpose. The saa7134 should call that whenever it sets a new samplerate.
Quoted 4 lines
Other question. For configure VideoFrontend need know 50 or 60Hz Now I use videomode from h structure. I think more correct detect it on saa7134.
Whether it is 50 or 60 Hz depends on the video standard that you receive via the s_std core op. Just implement that and when you get a new standard you can use something like this: is_60hz = (std & V4L2_STD_525_60) ? 1 : 0;
Some more review comments:
linux/drivers/media/video/saa7134/saa7134.h:
@@ -355,6 +377,10 @@
unsigned char empress_addr;
unsigned char rds_addr;+ /* SPI info */ + struct saa7134_software_spi spi; + struct spi_board_info spi_conf;
Make this a struct spi_board_info *. This struct is too large: it is only used in one board but all elements of the board array will suddenly get this whole struct increasing the memory footprint substantially. In this case you can just make it a pointer, that will work just as well.
+
unsigned int tda9887_conf;
unsigned int tuner_config;linux/drivers/media/video/v4l2-common.c, in v4l2_spi_subdev_init():
+ /* initialize name */
+ snprintf(sd->name, sizeof(sd->name), "%s",
+ spi->dev.driver->name);
Use strlcpy here.
saa7134-spi.c:
static inline u32 getmiso(struct spi_device *dev)
{
struct saa7134_spi_gpio *sb = to_sb(dev);
unsigned long status;
status = saa7134_get_gpio(sb->controller_data);
if ( status & (1 << sb->controller_data->spi.miso))
return 1;
else
return 0;
}Simplify to:
static inline u32 getmiso(struct spi_device *dev)
{
struct saa7134_spi_gpio *sb = to_sb(dev);
u32 status;
status = saa7134_get_gpio(sb->controller_data);
return !!(status & (1 << sb->controller_data->spi.miso));
}Also note that saa7134_get_gpio should return an u32 since unsigned long is 64 bits when compiled on a 64-bit kernel, which is probably not what you want.
saa7134_spi_unregister can be a void function as the result code is always 0.
There seems to be some old stuff in upd61151.h. Please remove what is not needed.
In upd61151.c I highly recommend that all functions will use struct v4l2_subdev *sd as argument. Only at the lowest level should you go from sd to spi. Among others this allows you to use the standard v4l2_info/dbg etc. logging functions.
Don't use RESULT_SUCCESS. Just return 0.
Remove upd61151_init. The init op is rarely needed and should in general not be used.
Remove those emacs editor comments at the end of the files. That's bad practice.
Regards,
Hans
Signature · 1 line
Hans Verkuil - video4linux developer - sponsored by TANDBERG
Hi
Some fixes
Quoted 14 lines · On Tuesday 09 February 2010 06:41:50 Dmitri Belimov wrote:
Quoted 13 lines
Hi Hans
This is my last state for review.
After small time I'll finish process of initialize the encoder. Configure some register, upload two firmware for video and for audio. Configure the frontends.I have the questions.
For configuring audio frontend need know samplerate of audio. saa7134 can only 32kHz
saa7131/3/5 on I2S 32кГц from SIF source and 32/44.1/48 from external i.e. RCA stereo audio input.
Quoted 5 lines
Quoted 1 line
Hardcode 32kHz or need a function for determine mode of audio??
See struct
v4l2_subdev_audio_ops: it has as_clock_freqop for precisely that purpose. The saa7134 should call that whenever it sets a new samplerate.
This op is not used in saa7134 sources. Now hardcoded 32kHz.
Quoted 9 lines
Quoted 4 lines
Other question. For configure VideoFrontend need know 50 or 60Hz Now I use videomode from h structure. I think more correct detect it on saa7134.
Whether it is 50 or 60 Hz depends on the video standard that you receive via the
s_stdcore op. Just implement that and when you get a new standard you can use something like this:is_60hz= (std &V4L2_STD_525_60) ? 1 : 0;
I do it, if(std & V4L2_STD_625_50) then ....
This data is not real information about input signal. It's what we set from end-user programm. But OK, I used it.
Quoted 12 lines
Some more review comments:
linux/drivers/media/video/saa7134/saa7134.h:(quoted diff) +3
-0@@ -355,6 +377,10 @@ unsigned char empress_addr; unsigned char rds_addr; + /* SPI info */ + struct saa7134_software_spi spi; + struct spi_board_info spi_conf;
Quoted 5 lines
Make this a struct
spi_board_info*. This struct is too large: it is only used in one board but all elements of the board array will suddenly get this whole struct increasing the memory footprint substantially. In this case you can just make it a pointer, that will work just as well.
Yes. I don't know what is more good. Now all config data in saa7134-cards description. In your case need move spi_board_info to SPI part of code. We will mix code and data. For add new cards and devices need edit some files for add configs.
May be it's good in my case.
Quoted 11 lines
+
unsigned int tda9887_conf; unsigned int tuner_config;
linux/drivers/media/video/v4l2-common.c, inv4l2_spi_subdev_init():(quoted diff) +3
-0+ /* initialize name */ + snprintf(sd->name, sizeof(sd->name), "%s", + spi->dev.driver->name);Use strlcpy here.
Done
Quoted 17 lines
saa7134-spi.c:static inline u32
getmiso(struct spi_device *dev){ struct saa7134_spi_gpio *sb = to_sb(dev); unsigned long status; status = saa7134_get_gpio(sb->controller_data); if ( status & (1 << sb->controller_data->spi.miso)) return 1; else return 0; }Simplify to:
Quoted 8 lines
static inline u32
getmiso(struct spi_device *dev){ struct saa7134_spi_gpio *sb = to_sb(dev); u32 status; status = saa7134_get_gpio(sb->controller_data); return !!(status & (1 << sb->controller_data->spi.miso)); }
Thank you.
Quoted 3 lines
Also note that
saa7134_get_gpioshould return an u32 since unsigned long is 64 bits when compiled on a 64-bit kernel, which is probably not what you want.
Done
Quoted 2 lines
saa7134_spi_unregistercan be a void function as the result code is always 0.
Done
Quoted 2 lines
There seems to be some old stuff in
upd61151.h. Please remove what is not needed.
Done
Quoted 4 lines
In
upd61151.cI highly recommend that all functions will use structv4l2_subdev*sd as argument. Only at the lowest level should you go from sd to spi. Among others this allows you to use the standard v4l2_info/dbg etc. logging functions.
Done
Quoted 1 line
Don't use
RESULT_SUCCESS. Just return 0.
Done
Quoted 2 lines
Remove
upd61151_init. The init op is rarely needed and should in general not be used.
Done
Quoted 2 lines
Remove those emacs editor comments at the end of the files. That's bad practice.
Done
With my best regards, Dmitry.
linux/drivers/media/video/saa7134/Makefile +2 -2
@@ -1,9 +1,9 @@ saa7134-objs := saa7134-cards.o saa7134-core.o saa7134-i2c.o \ saa7134-ts.o saa7134-tvaudio.o saa7134-vbi.o \ - saa7134-video.o saa7134-input.o + saa7134-video.o saa7134-input.o saa7134-spi.o -obj-$(CONFIG_VIDEO_SAA7134) += saa6752hs.o saa7134.o saa7134-empress.o +obj-$(CONFIG_VIDEO_SAA7134) += saa6752hs.o saa7134.o saa7134-empress.o upd61151.o obj-$(CONFIG_VIDEO_SAA7134_ALSA) += saa7134-alsa.o
linux/drivers/media/video/saa7134/saa7134-cards.c +31 -8
@@ -4619,6 +4619,7 @@ .name = name_radio, .amux = LINE2, }, + .encoder_type = SAA7134_ENCODER_SAA6752HS, .mpeg = SAA7134_MPEG_EMPRESS, .video_out = CCIR656, .vid_port_opts = (SET_T_CODE_POLARITY_NON_INVERTED |
@@ -4656,6 +4657,7 @@ .name = name_radio, .amux = LINE2, }, + .encoder_type = SAA7134_ENCODER_SAA6752HS, .mpeg = SAA7134_MPEG_EMPRESS, .video_out = CCIR656, .vid_port_opts = (SET_T_CODE_POLARITY_NON_INVERTED |
@@ -4695,6 +4697,7 @@ .name = name_radio, .amux = LINE2, }, + .encoder_type = SAA7134_ENCODER_SAA6752HS, .mpeg = SAA7134_MPEG_EMPRESS, .video_out = CCIR656, .vid_port_opts = (SET_T_CODE_POLARITY_NON_INVERTED |
@@ -5279,23 +5282,43 @@ .tuner_addr = ADDR_UNSET, .radio_addr = ADDR_UNSET, .mpeg = SAA7134_MPEG_DVB, + .gpiomask = 0x00860000, .inputs = { { .name = name_tv, .vmux = 2, .amux = TV, .tv = 1, - }, { - .name = name_comp1, - .vmux = 0, - .amux = LINE1, + .gpio =0x00860000 + }, { + .name = name_comp1, + .vmux = 0, + .amux = LINE1, + .gpio =0x00860000 }, { .name = name_svideo, .vmux = 9, .amux = LINE1, - } }, - .radio = { - .name = name_radio, - .amux = TV, + .gpio = 0x00860000 + } }, + .radio = { + .name = name_radio, + .amux = TV, + .gpio =0x00860000 + }, + .encoder_type = SAA7134_ENCODER_muPD61151, + .mpeg = SAA7134_MPEG_EMPRESS, + .video_out = CCIR656, + .vid_port_opts = (SET_T_CODE_POLARITY_NON_INVERTED | +SET_CLOCK_NOT_DELAYED | +SET_CLOCK_INVERTED | + SET_VSYNC_OFF), + .spi = { + .cs = 17, + .clock = 18, + .mosi = 23, + .miso = 21, + .num_chipselect = 1, + .spi_enable = 1, }, }, [SAA7134_BOARD_ZOLID_HYBRID_PCI] = {
linux/drivers/media/video/saa7134/saa7134-core.c +48 -3
78 lines not on this page · raw message
linux/drivers/media/video/saa7134/saa7134.h +44 -0
98 lines not on this page · raw message
linux/drivers/media/video/v4l2-common.c +61 -0
73 lines not on this page · raw message
linux/drivers/media/video/v4l2-device.c +8 -0
@@ -100,6 +100,14 @@ }#endif #endif +/* FIXME: ADD if def's for SPI subdevices */ +if (sd->flags &V4L2_SUBDEV_FL_IS_SPI ) { +struct spi_device *spi =v4l2_get_subdevdata (sd); + +if (spi) +spi_unregister_device (spi); + } + } }EXPORT_SYMBOL_GPL (v4l2_device_unregister);
linux/include/media/v4l2-chip-ident.h +5 -0
@@ -278,6 +278,11 @@/* module cs53132a: just ident 53132 */ V4L2_IDENT_CS53l32A =53132 , +/* modules upd61151 MPEG2 encoder: just ident 54000 */ +V4L2_IDENT_UPD61161 =54000 , +/* modules upd61152 MPEG2 encoder with AC3: just ident 54001 */ +V4L2_IDENT_UPD61162 =54001 , +/* module upd64031a: just ident 64031 */ V4L2_IDENT_UPD64031A = 64031,
linux/include/media/v4l2-common.h +19 -0
@@ -191,6 +191,25 @@/* ------------------------------------------------------------------------- */ +/* SPI Helper functions */ + +#include <linux/spi/spi.h> + +struct spi_device_id ; +struct spi_device ; + +/* Load an spi module and return an initialized v4l2_subdev struct. +Only call request_module if module_name != NULL. +The client_type argument is the name of the chip that's on the adapter. */ +struct v4l2_subdev *v4l2_spi_new_subdev (struct v4l2_device *v4l2_dev, +struct spi_master *master,struct spi_board_info *info); + +/* Initialize an v4l2_subdev with data from an spi_device struct */ +void v4l2_spi_subdev_init (struct v4l2_subdev *sd,struct spi_device *spi, +const struct v4l2_subdev_ops *ops); + +/* ------------------------------------------------------------------------- */ +/* Note: these remaining ioctls/structs should be removed as well, but they are still used in tuner-simple.c (TUNER_SET_CONFIG), cx18/ivtv (RESET) and v4l2-int-device.h (v4l2_routing). To remove these ioctls some more cleanup
linux/include/media/v4l2-subdev.h +2 -0
@@ -387,6 +387,8 @@/* Set this flag if this subdev is a i2c device. */ #define V4L2_SUBDEV_FL_IS_I2C (1U << 0) +/* Set this flag if this subdev is a spi device. */ +#define V4L2_SUBDEV_FL_IS_SPI (1U << 1)/* Each instance of a subdev driver should create this struct, either stand-alone or embedded in a larger struct.
/*
*
* Device driver for philips saa7134 based TV cards
* SPI software interface support
*
* (c) 2009 Beholder Intl. Ltd. Dmitry Belimov <[email protected]> *
* Important: now support ONLY SPI_MODE_0, see FIXME
*
* This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation; either version 2 of the License, or * (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*/
#include "saa7134-reg.h"
#include "saa7134.h"
#include <media/v4l2-common.h>
/* ----------------------------------------------------------- */
static unsigned int spi_debug; module_param(spi_debug, int, 0644); MODULE_PARM_DESC(spi_debug,"enable debug messages [spi]");
#define d1printk if (1 == spi_debug) printk
#define d2printk if (2 == spi_debug) printk
static inline void spidelay(unsigned d)
{
ndelay(d);
}static inline struct saa7134_spi_gpio *to_sb(struct spi_device *spi)
{
return spi_master_get_devdata(spi->master);
}static inline void setsck(struct spi_device *dev, int on)
{
struct saa7134_spi_gpio *sb = to_sb(dev);
saa7134_set_gpio(sb->controller_data, sb->controller_data->spi.clock, on ? 1 : 0);
}static inline void setmosi(struct spi_device *dev, int on)
{
struct saa7134_spi_gpio *sb = to_sb(dev);
saa7134_set_gpio(sb->controller_data, sb->controller_data->spi.mosi, on ? 1 : 0);
}static inline u32 getmiso(struct spi_device *dev)
{
struct saa7134_spi_gpio *sb = to_sb(dev);
unsigned long status;
status = saa7134_get_gpio(sb->controller_data);
return !!( status & (1 << sb->controller_data->spi.miso));
}#define EXPAND_BITBANG_TXRX 1
#include <linux/spi/spi_bitbang.h>
static void saa7134_spi_gpio_chipsel(struct spi_device *dev, int on)
{
struct saa7134_spi_gpio *sb = to_sb(dev);
if (on)
{
/* FIXME: set clock to zero by default, only SPI_MODE_0 compatible */
saa7134_set_gpio(sb->controller_data, sb->controller_data->spi.clock, 0);
saa7134_set_gpio(sb->controller_data, sb->controller_data->spi.cs, 0);
}
else
saa7134_set_gpio(sb->controller_data, sb->controller_data->spi.cs, 1);
}/* Our actual bitbanger routine. */
static u32 saa7134_txrx(struct spi_device *spi, unsigned nsecs, u32 word, u8 bits)
{
return bitbang_txrx_be_cpha0(spi, nsecs, 0, word, bits);
}int saa7134_spi_register(struct saa7134_dev *dev, struct spi_board_info *info)
{
struct spi_master *master = NULL;
struct saa7134_spi_gpio *sb = NULL;
int ret = 0;
master = spi_alloc_master(&dev->pci->dev, sizeof(struct saa7134_spi_gpio));
if (master == NULL)
{
dev_err(&dev->pci->dev, "failed to allocate spi master\n");
ret = -ENOMEM;
goto err;
}
sb = spi_master_get_devdata(master);
master->num_chipselect = dev->spi.num_chipselect;
master->bus_num = -1;
sb->master = spi_master_get(master);
sb->bitbang.master = sb->master;
sb->bitbang.master->bus_num = -1;
sb->bitbang.master->num_chipselect = dev->spi.num_chipselect;
sb->bitbang.chipselect = saa7134_spi_gpio_chipsel;
sb->bitbang.txrx_word[SPI_MODE_0] = saa7134_txrx;
/* set state of spi pins */
saa7134_set_gpio(dev, dev->spi.cs, 1);
/* FIXME: set clock to zero by default, only SPI_MODE_0 compatible */
saa7134_set_gpio(dev, dev->spi.clock, 0);
saa7134_set_gpio(dev, dev->spi.mosi, 1);
saa7134_set_gpio(dev, dev->spi.miso, 3);
/* start SPI bitbang master */
ret = spi_bitbang_start(&sb->bitbang);
if (ret) {
dev_err(&dev->pci->dev, "Failed to register SPI master\n");
goto err_no_bitbang;
}
dev_info(&dev->pci->dev,
"spi master registered: bus_num=%d num_chipselect=%d\n",
master->bus_num, master->num_chipselect);
sb->controller_data = dev;
info->bus_num = sb->master->bus_num;
info->controller_data = master;
dev->spi_adap = master;err_no_bitbang:
spi_master_put(master); err: return ret; }
void saa7134_spi_unregister(struct saa7134_dev *dev)
{
struct saa7134_spi_gpio *sb = spi_master_get_devdata(dev->spi_adap);
spi_bitbang_stop(&sb->bitbang);
spi_master_put(sb->master);
}/*
* Overrides for Emacs so that we follow Linus's tabbing style.
* ---------------------------------------------------------------------------
* Local variables:
* c-basic-offset: 8
* End:
*/
/*
upd61151 - driver for the uPD61151 by NEC
Copyright (C) Beholder Intl. Ltd. Dmitry Belimov <[email protected]>
Based on the saa6752s.c driver.
Copyright (C) 2004 Andrew de Quincey
This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License vs published by the Free Software Foundation; either version 2 of the License, or (at your option) any later version.
This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details.
You should have received a copy of the GNU General Public License along with this program; if not, write to the Free Software Foundation, Inc., 675 Mvss Ave, Cambridge, MA 02139, USA.
*/
#include <linux/init.h>
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/device.h>
#include <linux/sysfs.h>
#include <linux/string.h>
#include <linux/timer.h>
#include <linux/delay.h>
#include <linux/errno.h>
#include <linux/slab.h>
#include <linux/poll.h>
#include <linux/spi/spi.h>
#include <linux/types.h>
#include "compat.h"
#include <linux/videodev2.h>
#include <media/v4l2-device.h>
#include <media/v4l2-common.h>
#include <media/v4l2-chip-ident.h>
#include <media/upd61151.h>
#include <linux/crc32.h>
#include "saa7134.h"
#define DRVNAME "upd61151"
static unsigned int spi_debug; module_param(spi_debug, int, 0644); MODULE_PARM_DESC(spi_debug,"enable debug messages [spi]");
#define d1printk_spi if (1 <= spi_debug) printk
#define d2printk_spi if (2 <= spi_debug) printk
static unsigned int core_debug; module_param(core_debug, int, 0644); MODULE_PARM_DESC(core_debug,"enable debug messages [core]");
#define d1printk_core if (1 <= core_debug) printk
#define d2printk_core if (2 <= core_debug) printk
MODULE_DESCRIPTION("device driver for uPD61151 MPEG2 encoder"); MODULE_AUTHOR("Dmitry V Belimov"); MODULE_LICENSE("GPL");
/* Result codes */
#define RESULT_SUCCESS 0 #define RESULT_FAILURE 1 #define STATUS_DEVICE_NOT_READY 2 #define STATUS_DEVICE_DATA_ERROR 3
enum upd61151_videoformat {
UPD61151_VF_D1 = 0, /* 720x480/720x576 */
UPD61151_VF_D2 = 1, /* 704x480/704x576 */
UPD61151_VF_D3 = 2, /* 352x480/352x576 */
UPD61151_VF_D4 = 3, /* 352x240/352x288 */
UPD61151_VF_D5 = 4, /* 544x480/544x576 */
UPD61151_VF_D6 = 5, /* 480x480/480x576 */
UPD61151_VF_D7 = 6, /* 352x240/352x288 */
UPD61151_VF_D8 = 8, /* 640x480/640x576 */
UPD61151_VF_D9 = 9, /* 320x480/320x576 */
UPD61151_VF_D10 = 10, /* 320x240/320x288 */
UPD61151_VF_UNKNOWN,
};struct upd61151_mpeg_params {
/* transport streams */
__u16 ts_pid_pmt;
__u16 ts_pid_audio;
__u16 ts_pid_video;
__u16 ts_pid_pcr;
/* audio */
enum v4l2_mpeg_audio_encoding au_encoding;
enum v4l2_mpeg_audio_l2_bitrate au_l2_bitrate;
/* video */
enum v4l2_mpeg_video_aspect vi_aspect;
enum v4l2_mpeg_video_bitrate_mode vi_bitrate_mode;
__u32 vi_bitrate;
__u32 vi_bitrate_peak;
};static const struct v4l2_format v4l2_format_table[] =
{
[UPD61151_VF_D1] =
{ .fmt = { .pix = { .width = 720, .height = 576 }}},
[UPD61151_VF_D2] =
{ .fmt = { .pix = { .width = 704, .height = 576 }}},
[UPD61151_VF_D3] =
{ .fmt = { .pix = { .width = 352, .height = 576 }}},
[UPD61151_VF_D4] =
{ .fmt = { .pix = { .width = 352, .height = 288 }}},
[UPD61151_VF_D5] =
{ .fmt = { .pix = { .width = 544, .height = 576 }}},
[UPD61151_VF_D6] =
{ .fmt = { .pix = { .width = 480, .height = 576 }}},
[UPD61151_VF_D7] =
{ .fmt = { .pix = { .width = 352, .height = 288 }}},
[UPD61151_VF_D8] =
{ .fmt = { .pix = { .width = 640, .height = 576 }}},
[UPD61151_VF_D9] =
{ .fmt = { .pix = { .width = 320, .height = 576 }}},
[UPD61151_VF_D10] =
{ .fmt = { .pix = { .width = 320, .height = 288 }}},
[UPD61151_VF_UNKNOWN] =
{ .fmt = { .pix = { .width = 0, .height = 0}}},
};struct upd61151_state {
struct v4l2_subdev sd;
struct upd61151_mpeg_params params;
enum upd61151_videoformat video_format;
v4l2_std_id standard;
enum upd61151_encode_state enstate;
};static struct upd61151_mpeg_params param_defaults =
{
.ts_pid_pmt = 16,
.ts_pid_video = 260,
.ts_pid_audio = 256,
.ts_pid_pcr = 259,
.vi_aspect = V4L2_MPEG_VIDEO_ASPECT_4x3,
.vi_bitrate = 4000,
.vi_bitrate_peak = 6000,
.vi_bitrate_mode = V4L2_MPEG_VIDEO_BITRATE_MODE_VBR,
.au_encoding = V4L2_MPEG_AUDIO_ENCODING_LAYER_2,
.au_l2_bitrate = V4L2_MPEG_AUDIO_L2_BITRATE_256K,
};static int write_reg(struct spi_device *spi, u8 address, u8 data)
{
u8 buf[2];
buf[0] = ((address >> 2) << 2);
buf[1] = data;
d2printk_spi(KERN_DEBUG "%s: spi data 0x%x <= 0x%x\n",spi->modalias,address,data);
return spi_write(spi, buf, ARRAY_SIZE(buf));
}static void write_fw(struct spi_device *spi, u8 address, const struct firmware *fw)
{
u8 buf[2];
u32 i;
buf[0] = ((address >> 2) << 2);
for (i=0; i < fw->size; i++)
{
buf[1] = *(fw->data+i);
spi_write(spi, buf, 2);
}
}static int read_reg(struct spi_device *spi, unsigned char address, unsigned char *data)
{
u8 buf[1];
int ret;
ret = 0;
buf[0] = ((address >> 2) << 2) | 0x02;
ret = spi_write_then_read(spi, buf, 1, data, 1);
d2printk_spi(KERN_DEBUG "%s: spi data 0x%x => 0x%x, status %d\n",spi->modalias, address, *data, ret);
return ret;
}static u8 upd61151_get_state(struct v4l2_subdev *sd)
{
struct spi_device *spi = v4l2_get_subdevdata(sd);
u8 rbyte = 0x00;
read_reg(spi, UPD61151_STATUS, &rbyte);
d2printk_core(KERN_DEBUG "%s: MPEG2 core status %d\n", spi->modalias, rbyte & 0x07);
return rbyte & 0x07;
}static int upd61151_set_state(struct v4l2_subdev *sd, enum upd61151_config nstate) {printk("upd61151_set_state\n");
printk("WARNING: The function upd61151_set_state is EMPTY\n");
return RESULT_SUCCESS;
}static void upd61151_reset_core(struct v4l2_subdev *sd)
{
struct spi_device *spi = v4l2_get_subdevdata(sd);
write_reg(spi, UPD61151_SOFTWARE_RST, 0x01);
}static void upd61151_set_dest_addr(struct v4l2_subdev *sd, u32 addr)
{
struct spi_device *spi = v4l2_get_subdevdata(sd);
write_reg(spi, UPD61151_TRANSFER_ADDR1, (u8)((addr >> 16) & 0xFF));
write_reg(spi, UPD61151_TRANSFER_ADDR2, (u8)((addr >> 8) & 0xFF));
write_reg(spi, UPD61151_TRANSFER_ADDR3, (u8)(addr & 0xFF));
}static void upd61151_set_data_size(struct v4l2_subdev *sd, u32 dsize)
{
struct spi_device *spi = v4l2_get_subdevdata(sd);
write_reg(spi, UPD61151_DATA_COUNTER1, (u8)((dsize >> 16) & 0xFF));
write_reg(spi, UPD61151_DATA_COUNTER2, (u8)((dsize >> 8) & 0xFF));
write_reg(spi, UPD61151_DATA_COUNTER3, (u8)(dsize & 0xFF));
}static u8 upd61151_clear_transfer_irq(struct v4l2_subdev *sd)
{
struct spi_device *spi = v4l2_get_subdevdata(sd);
u8 rbyte = 0x00;
read_reg(spi, UPD61151_TRANSFER_IRQ, &rbyte);
d2printk_core(KERN_DEBUG "%s: Transfer IRQ status 0x%x\n", spi->modalias, rbyte);
if (rbyte)
write_reg(spi, UPD61151_IRQ, rbyte);
return rbyte;
}static void upd61151_handle_transfer_err(struct v4l2_subdev *sd)
{
struct spi_device *spi = v4l2_get_subdevdata(sd);
u8 rbyte;
printk("upd61151_handle_transfer_err\n");
/* Set data transfer count size = 1 */
upd61151_set_data_size(sd, 0x01);
/* Set transfer mode SDRAM -> Host */
write_reg(spi, UPD61151_TRANSFER_MODE, 0x01);
/* Read one byte from SDRAM */
read_reg(spi, UPD61151_TRANSFER_DATA, &rbyte);
/* Release transfer mode */
write_reg(spi, UPD61151_TRANSFER_MODE, 0x00);
/* Clear IRQ */
upd61151_clear_transfer_irq(sd);
/* Set destination address to 0x000000 */
upd61151_set_dest_addr(sd, 0x000000);
/* Set data transfer count size = 3 */
upd61151_set_data_size(sd, 0x03);
/* Set transfer mode SDRAM -> Host */
write_reg(spi, UPD61151_TRANSFER_MODE, 0x01);
/* Clear IRQ */
upd61151_clear_transfer_irq(sd);
/* Read 3 byte from SDRAM */
read_reg(spi, UPD61151_TRANSFER_DATA, &rbyte);
read_reg(spi, UPD61151_TRANSFER_DATA, &rbyte);
read_reg(spi, UPD61151_TRANSFER_DATA, &rbyte);
/* Clear IRQ */
upd61151_clear_transfer_irq(sd);
/* Set transfer mode SDRAM -> Host */
write_reg(spi, UPD61151_TRANSFER_MODE, 0x00);
/* Clear IRQ */
upd61151_clear_transfer_irq(sd);
}static int upd61151_wait_transfer_irq(struct v4l2_subdev *sd)
{
struct spi_device *spi = v4l2_get_subdevdata(sd);
u8 i, rstatus;
rstatus = 0;
/* Wait transfer interrupt */
for (i=0; i<5; i++)
{
rstatus = upd61151_clear_transfer_irq(sd);
if (rstatus)
break;
msleep(1);
}
if (!rstatus)
return STATUS_DEVICE_NOT_READY;
if (rstatus & 0x04)
{
/* Data transfer error */
upd61151_handle_transfer_err(sd);
return STATUS_DEVICE_DATA_ERROR;
}
return RESULT_SUCCESS;
}static u8 upd61151_clear_info_irq(struct v4l2_subdev *sd)
{
struct spi_device *spi = v4l2_get_subdevdata(sd);
u8 rbyte = 0x00;
read_reg(spi, UPD61151_IRQ, &rbyte);
d2printk_core(KERN_DEBUG "%s: IRQ status 0x%x\n", spi->modalias, rbyte);
if (rbyte)
write_reg(spi, UPD61151_IRQ, rbyte);
return rbyte;
}static u8 upd61151_clear_error_irq(struct v4l2_subdev *sd)
{
struct spi_device *spi = v4l2_get_subdevdata(sd);
u8 rbyte = 0x00;
read_reg(spi, UPD61151_ERROR_IRQ, &rbyte);
d2printk_core(KERN_DEBUG "%s: IRQ error status 0x%x\n", spi->modalias, rbyte);
if (rbyte)
write_reg(spi, UPD61151_ERROR_IRQ, rbyte);
return rbyte;
}static u8 upd61151_clear_except_irq(struct v4l2_subdev *sd)
{
struct spi_device *spi = v4l2_get_subdevdata(sd);
u8 rbyte = 0x00;
read_reg(spi, UPD61151_EXCEPT_IRQ, &rbyte);
d2printk_core(KERN_DEBUG "%s: IRQ exception status 0x%x\n", spi->modalias, rbyte);
if (rbyte)
write_reg(spi, UPD61151_EXCEPT_IRQ, rbyte);
return rbyte;
}static int upd61151_load_base_firmware(struct v4l2_subdev *sd)
{
struct spi_device *spi = v4l2_get_subdevdata(sd);
u32 size;
const struct firmware *fw;
int ret = RESULT_SUCCESS;printk("DEBUG: upd61151_load_base_firmware\n");
size = UPD61151_DEFAULT_PS_FIRMWARE_SIZE / 4;
/* request the firmware, this will block and timeout */
printk(KERN_INFO "%s: waiting for base firmware upload (%s)...\n",
spi->modalias, UPD61151_DEFAULT_PS_FIRMWARE);
ret = request_firmware(&fw, UPD61151_DEFAULT_PS_FIRMWARE,
spi->dev.parent);
if (ret)
{
printk(KERN_ERR "%s: Upload failed. (file not found?)\n",spi->modalias);
ret = RESULT_FAILURE;
goto out;
}
else
printk(KERN_DEBUG "%s: firmware read %Zu bytes.\n", spi->modalias,
fw->size);
if (fw->size != UPD61151_DEFAULT_PS_FIRMWARE_SIZE)
{
printk(KERN_ERR "%s: firmware incorrect size\n", spi->modalias);
ret = RESULT_FAILURE;
goto out;
}
printk(KERN_INFO "%s: base firmware uploading...\n", spi->modalias);
upd61151_clear_transfer_irq(sd);
/* CPU reset ON */
write_reg(spi, UPD61151_SOFTWARE_RST, 0x02);
/* Set destination address to 0x000000 */
upd61151_set_dest_addr(sd, 0x000000);
/* Set transfer data count to firmware size / 4 */
upd61151_set_data_size(sd, size);
/* Set transfer mode to Host -> iRAM */
write_reg(spi, UPD61151_TRANSFER_MODE, 0x80);
printk("fw upload start\n");
write_fw(spi, UPD61151_TRANSFER_DATA, fw);printk("fw upload stop\n");
if (upd61151_wait_transfer_irq(sd) == RESULT_SUCCESS)
{
/* Release transfer mode */
write_reg(spi, UPD61151_TRANSFER_MODE, 0x00);
printk(KERN_INFO "%s: base firmware upload complete...\n", spi->modalias);
}
else
printk(KERN_INFO "%s: base firmware upload FAIL...\n", spi->modalias);out:
/* CPU reset OFF */ write_reg(spi, UPD61151_SOFTWARE_RST, 0x00); release_firmware(fw); return ret; }
static int upd61151_load_audio_firmware(struct v4l2_subdev *sd)
{
struct spi_device *spi = v4l2_get_subdevdata(sd);
const struct firmware *fw;
u32 addr, i;
int ret = RESULT_SUCCESS;printk("DEBUG: upd61151_load_audio_firmware\n");
/* request the firmware, this will block and timeout */
printk(KERN_INFO "%s: waiting for audio firmware upload (%s)...\n",
spi->modalias, UPD61151_DEFAULT_AUDIO_FIRMWARE);
ret = request_firmware(&fw, UPD61151_DEFAULT_AUDIO_FIRMWARE,
spi->dev.parent);
if (ret)
{
printk(KERN_ERR "%s: Upload failed. (file not found?)\n",spi->modalias);
ret = RESULT_FAILURE;
goto out;
}
else
printk(KERN_DEBUG "%s: firmware read %Zu bytes.\n", spi->modalias,
fw->size);
if (fw->size != UPD61151_DEFAULT_AUDIO_FIRMWARE_SIZE)
{
printk(KERN_ERR "%s: firmware incorrect size\n", spi->modalias);
ret = RESULT_FAILURE;
goto out;
}
printk(KERN_INFO "%s: audio firmware uploading...\n", spi->modalias);
addr = 0x308F00;
addr >>= 5;
upd61151_clear_transfer_irq(sd);
/* Set destination address */
upd61151_set_dest_addr(sd, addr);
/* Set transfer data count to firmware size */
upd61151_set_data_size(sd, UPD61151_DEFAULT_AUDIO_FIRMWARE_SIZE);
/* Set transfer mode to Host -> SDRAM */
write_reg(spi, UPD61151_TRANSFER_MODE, 0x02);printk("fw upload start\n");
for (i = 0; i < UPD61151_DEFAULT_AUDIO_FIRMWARE_SIZE; i++)
{
write_reg(spi, UPD61151_TRANSFER_DATA, *(fw->data+i));
/* Check Transfer interrupt each 128 bytes */
if ( ((i+1) % 128) ==0 )
{
ret = upd61151_wait_transfer_irq(sd);
if (ret != RESULT_SUCCESS)
break;
}
}printk("fw upload stop\n");
if (ret == RESULT_SUCCESS)
{
/* Release transfer mode */
write_reg(spi, UPD61151_TRANSFER_MODE, 0x00);
printk(KERN_INFO "%s: audio firmware upload complete...\n", spi->modalias);
}
else
printk(KERN_INFO "%s: audio firmware upload FAIL...\n", spi->modalias);out:
release_firmware(fw); return ret; }
static int upd61151_chip_command(struct v4l2_subdev *sd, enum upd61151_command command)
{
struct spi_device *spi = v4l2_get_subdevdata(sd);
u8 cycles, wait, i, irqerr;
enum upd61151_command want_state;printk("DEBUG uPD61151: upd61151_chip_command\n");
/* calculate delay */
cycles = 100;
wait = 10;
switch (command)
{
case UPD61151_COMMAND_STANDBY_STOP:
case UPD61151_COMMAND_PAUSE:
break;
case UPD61151_COMMAND_START_RESTART:
cycles = 200;
wait = 1;
break;
default:
return RESULT_FAILURE;
}
/* Clear IRQ */
upd61151_clear_error_irq(sd);
write_reg(spi, UPD61151_COMMAND, command);
for (i=0; i < cycles; i++)
{
/* Check state */
want_state = upd61151_get_state(sd);
if (want_state == command)
{
upd61151_clear_info_irq(sd);
d2printk_core(KERN_DEBUG "%s: SetState %d SUCCESS, delay [%d ms].\n", spi->modalias, want_state, i*wait);
return 0;
}
/* Check error interrupt */
irqerr = upd61151_clear_error_irq(sd);
if (irqerr & 0x01)
{
d2printk_core(KERN_DEBUG "%s: SetState %d FAIL, Invalid Command (IC).\n", spi->modalias, command);
break;
}
if (irqerr & 0x02)
{
d2printk_core(KERN_DEBUG "%s: SetState %d FAIL, Invalid Parameter (IP).\n", spi->modalias, command);
break;
}
if (irqerr & 0x04)
{
d2printk_core(KERN_DEBUG "%s: SetState %d FAIL, Invalid Audio Firmware Download (IADL).\n", spi->modalias, command);
break;
}
if (irqerr & 0x08)
{
d2printk_core(KERN_DEBUG "%s: SetState %d FAIL, Invalid System Bit Rate (ISBR).\n", spi->modalias, command);
break;
}
msleep(wait);
}
if (i >= cycles)
{
d2printk_core(KERN_DEBUG "%s: SetState %d FAIL, TIMEOUT [%d ms].\n", spi->modalias, command, cycles*wait);
}
return RESULT_FAILURE;
}static int upd61151_setup_video_frontend(struct v4l2_subdev *sd)
{
struct spi_device *spi = v4l2_get_subdevdata(sd);
struct upd61151_state *h = spi_get_drvdata(spi);
u8 dbyte;printk("upd61151_setup_video_frontend\n");
dbyte = 0x00;
printk("dbyte = 0x%x ",dbyte);
/* Update FIDT */
if (h->standard & V4L2_STD_625_50)
dbyte |= 0x10;
printk(" 0x%x ",dbyte);
dbyte |= h->video_format;
printk(" 0x%x \n",dbyte);
write_reg(spi, UPD61151_VIDEO_ATTRIBUTE, dbyte);
/* SAV/EAV (ITU-656), FID not inverted */
write_reg(spi, UPD61151_VIDEO_SYNC, 0x80);
/* Set H offset */
write_reg(spi, UPD61151_VIDEO_HOFFSET, 0x00);
/* Set V offset */
if (h->standard & V4L2_STD_625_50)
dbyte = 0x01;
else
dbyte = 0x03;
write_reg(spi, UPD61151_VIDEO_VOFFSET, dbyte);
/* Setup VBI */
/* SLCEN = 0, VBIOFFV = 4, VBIOFFH = 8*/
write_reg(spi, UPD61151_VBI_ADJ1, 0x48);
return 0;
}static int upd61151_setup_audio_frontend(struct v4l2_subdev *sd)
{
struct spi_device *spi = v4l2_get_subdevdata(sd);printk("upd61151_setup_audio_frontend\n");
/* Setup AUDIO attribute 1 */
/* FIXME: hardcoded samplerate of audio to 32kHz */
/* default bitrate is 256Kbit */
write_reg(spi, UPD61151_AUDIO_ATTRIBUTE1, 0x29);
/* PLLs = internal, AMCLK = 384fs, AQ = 16bit & 64bck, APCMI = I2S, APCMO = OFF*/
write_reg(spi, UPD61151_AUDIO_INTERFACE, 0x5B);
return 0;
}static int upd61151_config_encoder(struct v4l2_subdev *sd)
{
struct spi_device *spi = v4l2_get_subdevdata(sd);
struct upd61151_state *h = spi_get_drvdata(spi);printk("upd61151_config_encoder\n");printk("WARNING: The function upd61151_config_encoder is EMPTY\n");
return 0; }
static int upd61151_download_firmware(struct v4l2_subdev *sd)
{
struct spi_device *spi = v4l2_get_subdevdata(sd);
struct upd61151_state *h = spi_get_drvdata(spi);printk("DEBUG: upd61151_download_firmware\n");
h->enstate = UPD61151_ENCODE_STATE_IDLE;
upd61151_reset_core(sd);
udelay(1);
/* Init SDRAM */
write_reg(spi, UPD61151_SDRAM_IF_DELAY_ADJ, 0x01);
write_reg(spi, UPD61151_SDRAM_FCLK_SEL, 0xA0);
udelay(200);
/* Set SDRAM to STANDBY */
write_reg(spi, UPD61151_SDRAM_STANDBY, 0x01);
udelay(10);
/* Release SDRAM from STANDBY */
write_reg(spi, UPD61151_SDRAM_STANDBY, 0x00);
if (upd61151_load_base_firmware(sd))
return RESULT_FAILURE;
if (upd61151_load_audio_firmware(sd))
return RESULT_FAILURE;
/* Clear IRQ flags */
if ( !(upd61151_clear_info_irq(sd) & 0x10) )
{
/* INICM not running */
d1printk_core(KERN_DEBUG "%s: download firmware FAILED. INICM is not run.\n", spi->modalias);
return RESULT_FAILURE;
}
/* Set STANDBY state */
if (upd61151_chip_command(sd, UPD61151_COMMAND_STANDBY_STOP))
return RESULT_FAILURE;
/* Setup video input frontend */
upd61151_setup_video_frontend(sd);
/* Setup audio input frontend */
upd61151_setup_audio_frontend(sd);
/* Config encoder params */
upd61151_config_encoder(sd);
/* Set all config and upload audio firmware */
if (upd61151_set_state(sd, UPD61151_CONFIG_ALL))
return RESULT_FAILURE;
/* Return to STANDBY state */
if (upd61151_chip_command(sd, UPD61151_COMMAND_STANDBY_STOP))
return RESULT_FAILURE;
return 0;
}static int upd61151_is_need_reload_fw(struct v4l2_subdev *sd)
{
struct spi_device *spi = v4l2_get_subdevdata(sd);
if (upd61151_get_state(sd) == UPD61151_COMMAND_INITIAL)
{
d1printk_core(KERN_DEBUG "%s: need reload firmware\n", spi->modalias);
return 1;
}
if (upd61151_clear_except_irq(sd) & 0x04)
{
d1printk_core(KERN_DEBUG "%s: mainly buffer of encoder is overflowed\n", spi->modalias);
return 1;
}
return 0;
}static int upd61151_set_bitrate(struct v4l2_subdev *sd,
struct upd61151_state *h)
{
printk("DEBUG uPD61151: upd61151_set_bitrate\n");
printk("WARNING: The function upd61151_set_bitrate is EMPTY\n");
return 0;
}static int upd61151_queryctrl(struct v4l2_subdev *sd, struct v4l2_queryctrl *qctrl) {printk("DEBUG uPD61151: upd61151_queryctrl\n");
printk("WARNING: The function upd61151_queryctrl is EMPTY\n");
return 0;
}static int upd61151_querymenu(struct v4l2_subdev *sd, struct v4l2_querymenu *qmenu) {printk("DEBUG uPD61151: upd61151_querymenu\n");
printk("WARNING: The function upd61151_querymenu is EMPTY\n");
return 0;
}static int upd61151_do_ext_ctrls(struct v4l2_subdev *sd, struct v4l2_ext_controls *ctrls, int set) {printk("DEBUG uPD61151: upd61151_do_ext_ctrls\n");
printk("WARNING: The function upd61151_do_ext_ctrls is EMPTY\n");
return 0;
}static int upd61151_s_ext_ctrls(struct v4l2_subdev *sd, struct v4l2_ext_controls *ctrls) {
printk("DEBUG uPD61151: upd61151_s_ext_ctrls\n");
return upd61151_do_ext_ctrls(sd, ctrls, 1);
}static int upd61151_try_ext_ctrls(struct v4l2_subdev *sd, struct v4l2_ext_controls *ctrls) {
printk("DEBUG uPD61151: upd61151_s_ext_ctrls\n");
return upd61151_do_ext_ctrls(sd, ctrls, 0);
}static int upd61151_g_ext_ctrls(struct v4l2_subdev *sd, struct v4l2_ext_controls *ctrls) {printk("DEBUG uPD61151: upd61151_g_ext_ctrls\n");
printk("WARNING: The function upd61151_g_ext_ctrls is EMPTY\n");
return 0;
}static int upd61151_g_fmt(struct v4l2_subdev *sd, struct v4l2_format *f)
{
struct spi_device *spi = v4l2_get_subdevdata(sd);
struct upd61151_state *h = spi_get_drvdata(spi);
if (h->video_format == UPD61151_VF_UNKNOWN)
h->video_format = UPD61151_VF_D1;
f->fmt.pix.width =
v4l2_format_table[h->video_format].fmt.pix.width;
f->fmt.pix.height =
v4l2_format_table[h->video_format].fmt.pix.height;printk("DEBUG uPD61151: upd61151_g_fmt\n");
return 0;
}static int upd61151_s_fmt(struct v4l2_subdev *sd, struct v4l2_format *f)
{
struct spi_device *spi = v4l2_get_subdevdata(sd);
struct upd61151_state *h = spi_get_drvdata(spi);printk("DEBUG uPD61151: upd61151_s_fmt\n");
if (f->fmt.pix.width <= 320)
{
if (f->fmt.pix.height <= 288)
{
f->fmt.pix.width = 320;
f->fmt.pix.height = 288;
h->video_format = UPD61151_VF_D10;
return 0;
}
else
{
f->fmt.pix.width = 320;
f->fmt.pix.height = 576;
h->video_format = UPD61151_VF_D9;
return 0;
}
}
if (f->fmt.pix.width <= 352)
{
if (f->fmt.pix.height <= 288)
{
f->fmt.pix.width = 352;
f->fmt.pix.height = 288;
h->video_format = UPD61151_VF_D4;
return 0;
}
else
{
f->fmt.pix.width = 352;
f->fmt.pix.height = 576;
h->video_format = UPD61151_VF_D3;
return 0;
}
}
if (f->fmt.pix.width <= 480)
{
f->fmt.pix.width = 480;
f->fmt.pix.height = 576;
h->video_format = UPD61151_VF_D6;
return 0;
}
if (f->fmt.pix.width <= 544)
{
f->fmt.pix.width = 544;
f->fmt.pix.height = 576;
h->video_format = UPD61151_VF_D5;
return 0;
}
if (f->fmt.pix.width <= 640)
{
f->fmt.pix.width = 640;
f->fmt.pix.height = 576;
h->video_format = UPD61151_VF_D8;
return 0;
}
if (f->fmt.pix.width <= 704)
{
f->fmt.pix.width = 704;
f->fmt.pix.height = 576;
h->video_format = UPD61151_VF_D2;
return 0;
}
f->fmt.pix.width = 720;
f->fmt.pix.height = 576;
h->video_format = UPD61151_VF_D1;
return 0;
}static int upd61151_s_std(struct v4l2_subdev *sd, v4l2_std_id std)
{
struct spi_device *spi = v4l2_get_subdevdata(sd);
struct upd61151_state *h = spi_get_drvdata(spi);
printk("DEBUG uPD61151: upd61151_s_std\n");
h->standard = std;
return 0;
}static int upd61151_g_chip_ident(struct v4l2_subdev *sd, struct v4l2_dbg_chip_ident *chip) {
printk("DEBUG uPD61151: upd61151_g_chip_ident\n");
chip->ident = V4L2_IDENT_UPD61161;
chip->revision = 0;
return 0;
}/* ----------------------------------------------------------------------- */
static const struct v4l2_subdev_core_ops upd61151_core_ops = {
.g_chip_ident = upd61151_g_chip_ident,
.queryctrl = upd61151_queryctrl,
.querymenu = upd61151_querymenu,
.g_ext_ctrls = upd61151_g_ext_ctrls,
.s_ext_ctrls = upd61151_s_ext_ctrls,
.try_ext_ctrls = upd61151_try_ext_ctrls,
.s_std = upd61151_s_std,
};static const struct v4l2_subdev_video_ops upd61151_video_ops = {
.s_fmt = upd61151_s_fmt,
.g_fmt = upd61151_g_fmt,
};static const struct v4l2_subdev_ops upd61151_ops = {
.core = &upd61151_core_ops,
.video = &upd61151_video_ops,
};static int __devinit upd61151_probe(struct spi_device *spi)
{
struct upd61151_state *h = kzalloc(sizeof(*h), GFP_KERNEL);
struct v4l2_subdev *sd;printk("upd61151_probe function\n");
if (h == NULL)
return -ENOMEM;
sd = &h->sd;
v4l2_spi_subdev_init(sd, spi, &upd61151_ops);
spi_set_drvdata(spi, h);
if (upd61151_is_need_reload_fw(sd))
{
printk("Start load firmware...\n");
if (!upd61151_download_firmware(sd))
printk("Firmware downloaded SUCCESS!!!\n");
else
printk("Firmware downloaded FAIL!!!\n");
}
else
printk("Firmware is OK\n");
h->params = param_defaults;
h->standard = 0; /* Assume 625 input lines */
return 0;
}static int __devexit upd61151_remove(struct spi_device *spi)
{
struct upd61151_state *h = spi_get_drvdata(spi);
printk("upd61151_remove function\n");
v4l2_device_unregister_subdev(&h->sd);
// kfree(&h->sd);
kfree(h);
spi_unregister_device(spi);
return 0;
}static struct spi_driver upd61151_driver = {
.driver = {
.name = DRVNAME,
.bus = &spi_bus_type,
.owner = THIS_MODULE,
},
.probe = upd61151_probe,
.remove = __devexit_p(upd61151_remove),
};static int __init init_upd61151(void)
{
return spi_register_driver(&upd61151_driver);
}module_init(init_upd61151);
static void __exit exit_upd61151(void)
{
spi_unregister_driver(&upd61151_driver);
}module_exit(exit_upd61151);
/*
upd61151.h - definition for NEC uPD61151 MPEG encoder
Copyright (C) Beholder Intl. Ltd. Dmitry Belimov <[email protected]>
This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation; either version 2 of the License, or (at your option) any later version.
This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details.
You should have received a copy of the GNU General Public License along with this program; if not, write to the Free Software Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*/
#include <linux/firmware.h>
#define UPD61151_DEFAULT_PS_FIRMWARE "D61151_PS_7133_v22_031031.bin" #define UPD61151_DEFAULT_PS_FIRMWARE_SIZE 97002
#define UPD61151_DEFAULT_AUDIO_FIRMWARE "audrey_MPE_V1r51.bin" #define UPD61151_DEFAULT_AUDIO_FIRMWARE_SIZE 40064
enum mpeg_video_bitrate_mode {
MPEG_VIDEO_BITRATE_MODE_VBR = 0, /* Variable bitrate */ MPEG_VIDEO_BITRATE_MODE_CBR = 1, /* Constant bitrate */
MPEG_VIDEO_BITRATE_MODE_MAX
};
enum mpeg_audio_bitrate {
MPEG_AUDIO_BITRATE_128 = 5, /* 128 kBit/sec */
MPEG_AUDIO_BITRATE_160 = 6, /* 160 kBit/sec */
MPEG_AUDIO_BITRATE_192 = 7, /* 192 kBit/sec */
MPEG_AUDIO_BITRATE_224 = 8, /* 224 kBit/sec */
MPEG_AUDIO_BITRATE_256 = 9, /* 256 kBit/sec */
MPEG_AUDIO_BITRATE_320 = 10, /* 320 kBit/sec */
MPEG_AUDIO_BITRATE_384 = 11, /* 384 kBit/sec */
MPEG_AUDIO_BITRATE_MAX
};enum mpeg_video_format {
MPEG_VIDEO_FORMAT_D1 = 0, /* 720x480/720x576 */
MPEG_VIDEO_FORMAT_D2 = 1, /* 704x480/704x576 */
MPEG_VIDEO_FORMAT_D3 = 2, /* 352x480/352x576 */
MPEG_VIDEO_FORMAT_D4 = 3, /* 352x240/352x288 */
MPEG_VIDEO_FORMAT_D5 = 4, /* 544x480/544x576 */
MPEG_VIDEO_FORMAT_D6 = 5, /* 480x480/480x576 */
MPEG_VIDEO_FORMAT_D7 = 6, /* 352x240/352x288 */
MPEG_VIDEO_FORMAT_D8 = 8, /* 640x480/640x576 */
MPEG_VIDEO_FORMAT_D9 = 9, /* 320x480/320x576 */
MPEG_VIDEO_FORMAT_D10 = 10, /* 320x240/320x288 */
MPEG_VIDEO_FORMAT_MAX
};#define MPEG_VIDEO_TARGET_BITRATE_MAX 15000
#define MPEG_VIDEO_MAX_BITRATE_MAX 15000
#define MPEG_TOTAL_BITRATE_MAX 15000
#define MPEG_PID_MAX ((1 << 14) - 1)
/* FIXME START: OLD FROM SAA6752HS */
struct mpeg_params {
enum mpeg_video_bitrate_mode video_bitrate_mode;
unsigned int video_target_bitrate;
unsigned int video_max_bitrate; // only used for VBR
enum mpeg_audio_bitrate audio_bitrate;
unsigned int total_bitrate;
unsigned int pmt_pid;
unsigned int video_pid;
unsigned int audio_pid;
unsigned int pcr_pid;
enum mpeg_video_format video_format;
};/* FIXME STOP: OLD FROM SAA6752HS */
enum upd61151_command {
UPD61151_COMMAND_INITIAL = 0,
UPD61151_COMMAND_STANDBY_STOP = 1,
UPD61151_COMMAND_CONFIG = 2,
UPD61151_COMMAND_START_RESTART = 3,
UPD61151_COMMAND_PAUSE = 4,
UPD61151_COMMAND_CHANGE = 5,
};enum upd61151_encode_state {
UPD61151_ENCODE_STATE_IDLE = 0,
UPD61151_ENCODE_STATE_ENCODE = 1,
UPD61151_ENCODE_STATE_PAUSE = 2,
};enum upd61151_config {
UPD61151_CONFIG_ALL = 0x00,
UPD61151_CONFIG_AUDIO_FW = 0x10,
UPD61151_CONFIG_VIDEO_INPUT = 0x20,
UPD61151_CONFIG_VBI_INPUT = 0x30,
UPD61151_CONFIG_AUDIO_INPUT = 0x40,
};#define UPD61151_COMMAND 0x00 #define UPD61151_STATUS 0x04 #define UPD61151_VIDEO_ATTRIBUTE 0x1C #define UPD61151_VIDEO_MODE 0x20 #define UPD61151_AUDIO_ATTRIBUTE1 0x2C #define UPD61151_VIDEO_SYNC 0x54 #define UPD61151_VIDEO_HOFFSET 0x58 #define UPD61151_VIDEO_VOFFSET 0x5C #define UPD61151_AUDIO_INTERFACE 0x60 #define UPD61151_VBI_ADJ1 0x74 #define UPD61151_VBI_ADJ2 0x78 #define UPD61151_TRANSFER_MODE 0x80 #define UPD61151_TRANSFER_ADDR1 0x90 #define UPD61151_TRANSFER_ADDR2 0x94 #define UPD61151_TRANSFER_ADDR3 0x98 #define UPD61151_DATA_COUNTER1 0x9C #define UPD61151_DATA_COUNTER2 0xA0 #define UPD61151_DATA_COUNTER3 0xA4 #define UPD61151_TRANSFER_IRQ 0xC0 #define UPD61151_IRQ 0xC4 #define UPD61151_ERROR_IRQ 0xCC #define UPD61151_EXCEPT_IRQ 0xD0 #define UPD61151_SDRAM_IF_DELAY_ADJ 0xDC #define UPD61151_SDRAM_FCLK_SEL 0xE0 #define UPD61151_SDRAM_STANDBY 0xE8 #define UPD61151_SOFTWARE_RST 0xF8 #define UPD61151_TRANSFER_DATA 0xFC
/*
* Local variables:
* c-basic-offset: 8
* End:
*/
eb1a:2860 eMPIA em28xx device to usb1 ??? usb hub problem?
In reply to Dmitri BelimovHi I get trouble with my Kworld em28xx device, anyone can help any kernel issue found somewhere about that?
Bus 001 Device 005: ID eb1a:2860 eMPIA Technology, Inc.
The device seems to go to usb1 hub and its usb2
Using kernel : 2.6.27-7-generic
LSUSB
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 005: ID eb1a:2860 eMPIA Technology, Inc. Bus 001 Device 004: ID 046d:c404 Logitech, Inc. TrackMan Wheel Bus 001 Device 003: ID 04d9:1603 Holtek Semiconductor, Inc. Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
DMESG
[ 2.429146] usbcore: registered new interface driver usbfs [ 2.429164] usbcore: registered new interface driver hub [ 2.429216] usbcore: registered new device driver usb [ 2.518153] usb usb1: configuration #1 chosen from 1 choice [ 2.900018] usb 1-1: new low speed USB device using ohci_hcd and address 2 [ 2.912659] usb usb2: configuration #1 chosen from 1 choice [ 3.576015] usb 2-3: new high speed USB device using ehci_hcd and address 4 [ 4.096019] usb 2-3: device not accepting address 4, error -71 [ 4.208015] usb 2-3: new high speed USB device using ehci_hcd and address 5 [ 4.340706] usb 2-3: configuration #1 chosen from 1 choice [ 4.644571] usb 1-1: new low speed USB device using ohci_hcd and address 3 [ 4.876163] usb 1-1: configuration #1 chosen from 1 choice [ 5.180015] usb 1-2: new low speed USB device using ohci_hcd and address 4 [ 5.393407] usb 1-2: configuration #1 chosen from 1 choice [ 5.396625] usb 2-3: USB disconnect, address 5 [ 5.636017] usb 2-3: new high speed USB device using ehci_hcd and address 6 [ 5.768459] usb 2-3: configuration #1 chosen from 1 choice [ 5.768794] usbcore: registered new interface driver hiddev [ 5.772486] usb 2-3: USB disconnect, address 6 [ 5.781319] input: USB Keyboard as /devices/pci0000:00/0000:00:02.0/usb1/1-1/1-1:1.0/input/input1 [ 5.784136] input,hidraw0: USB HID v1.10 Keyboard [ USB Keyboard] on usb-0000:00:02.0-1 [ 5.807105] input: USB Keyboard as /devices/pci0000:00/0000:00:02.0/usb1/1-1/1-1:1.1/input/input2 [ 5.807351] input,hidraw1: USB HID v1.10 Device [ USB Keyboard] on usb-0000:00:02.0-1 [ 5.814365] input: Logitech Trackball as /devices/pci0000:00/0000:00:02.0/usb1/1-2/1-2:1.0/input/input3 [ 5.814594] input,hidraw2: USB HID v1.10 Mouse [Logitech Trackball] on usb-0000:00:02.0-2 [ 5.814611] usbcore: registered new interface driver usbhid [ 5.814614] usbhid: v2.6:USB HID core driver [ 6.048518] usb 2-3: new high speed USB device using ehci_hcd and address 7 [ 6.568017] usb 2-3: device not accepting address 7, error -71 [ 6.680026] usb 2-3: new high speed USB device using ehci_hcd and address 8 [ 7.192521] usb 1-3: new full speed USB device using ohci_hcd and address 5 [ 7.393043] usb 1-3: not running at top speed; connect to a high speed hub [ 7.399169] usb 1-3: configuration #1 chosen from 1 choice [ 13.927208] em28xx Doesn't have usb audio class [ 14.934118] input: em28xx snapshot button as /devices/pci0000:00/0000:00:02.0/usb1/1-3/input/input7 [ 16.785083] usbcore: registered new interface driver em28xx [ 16.909506] em28xx-audio.c: probing for em28x1 non standard usbaudio [ 18.609828] usbcore: usbfs: unrecognised mount option "default" or missing value [ 18.609834] usbcore: usbfs: mount parameter error:
LSPCI
00:00.0 RAM memory: nVidia Corporation MCP61 Memory Controller (rev a1)
00:01.0 ISA bridge: nVidia Corporation MCP61 LPC Bridge (rev a2)
00:01.1 SMBus: nVidia Corporation MCP61 SMBus (rev a2)
00:01.2 RAM memory: nVidia Corporation MCP61 Memory Controller (rev a2)
00:02.0 USB Controller: nVidia Corporation MCP61 USB Controller (rev a3)
00:02.1 USB Controller: nVidia Corporation MCP61 USB Controller (rev a3)
00:04.0 PCI bridge: nVidia Corporation MCP61 PCI bridge (rev a1)
00:05.0 Audio device: nVidia Corporation MCP61 High Definition Audio (rev a2)
00:07.0 Bridge: nVidia Corporation MCP61 Ethernet (rev a2)
00:08.0 IDE interface: nVidia Corporation MCP61 SATA Controller (rev a2)
00:09.0 PCI bridge: nVidia Corporation MCP61 PCI Express bridge (rev a2)
00:0b.0 PCI bridge: nVidia Corporation MCP61 PCI Express bridge (rev a2)
00:0c.0 PCI bridge: nVidia Corporation MCP61 PCI Express bridge (rev a2)
00:0d.0 VGA compatible controller: nVidia Corporation GeForce 6150SE nForce 430 (rev a2) 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 01:07.0 Ethernet controller: VIA Technologies, Inc. VT6105/VT6106S [Rhine-III] (rev 86)
--
This message has been verified by LastSpam (http://www.lastspam.com) eMail security service, provided by SoluLAN Ce courriel a ete verifie par le service de securite pour courriels LastSpam (http://www.lastspam.com), fourni par SoluLAN (http://www.solulan.com) www.solulan.com
Re: eb1a:2860 eMPIA em28xx device to usb1 ??? usb hub problem?
Quoted 2 lines · On Mon, Feb 22, 2010 at 5:38 PM, j <[email protected]> wrote:
Hi I get trouble with my Kworld em28xx device, anyone can help any kernel issue found somewhere about that?
Hi J,
Is this device plugged directly into the USB port on the motherboard? Or do you have a USB hub that the device is connected to. Sometimes low quality USB hubs will not work properly with high speed isoc devices.
Also, I would suggest that you leave the device unplugged when powering up the system. Then once it is up, plug it in and send the full dmesg output. This will make it easier to analyze the dmesg output because the driver will not be initializing at the same time as all the other USB devices.
Also, please provide the *full* dmesg output, so we have more context information about the system (things such as the kernel version, etc).
Cheers,
Devin
Signature · 2 lines
Devin J. Heitmueller - Kernel Labs http://www.kernellabs.com
Re: eb1a:2860 eMPIA em28xx device to usb1 ??? usb hub problem?
Hi,
I have the KWorld DVB-T 305U, an em28xx device. Only the video works for me under Linux, no audio. In case anyone wants to see it, I have attached the full dmesg text, solely from this device.
Cheers,
Dean
Quoted 8 lines · Devin Heitmueller
....
Also, please provide the *full* dmesg output, so we have more context information about the system (things such as the kernel version, etc).Cheers,
Devin
Re: eb1a:2860 eMPIA em28xx device to usb1 ??? usb hub problem?
Quoted 6 lines · Dean
Hi,
I have the KWorld DVB-T 305U, an em28xx device. Only the video works for me under Linux, no audio. In case anyone wants to see it, I have attached the full dmesg text, solely from this device.
Cheers,
Dean
Hi Dean,
How are you testing the audio, and under what video standard are you trying to use the device (NTSC/PAL/SECAM)?
Devin
Signature · 2 lines
Devin J. Heitmueller - Kernel Labs http://www.kernellabs.com
Re: eb1a:2860 eMPIA em28xx device to usb1 ??? usb hub problem?
Quoted 8 lines · Devin Heitmueller
Quoted 6 lines · Dean
Hi,
I have the KWorld DVB-T 305U, an em28xx device. Only the video works for me under Linux, no audio. In case anyone wants to see it, I have attached the full dmesg text, solely from this device.
Cheers,
Dean
Quoted 7 lines
Hi Dean,
How are you testing the audio, and under what video standard are you trying to use the device (NTSC/PAL/SECAM)?
Devin
Devin
I am receiving NTSC TV signals. I test with mplayer. Example;
mplayer tv://9 -tv driver=v4l2:alsa:immediatemode=0:adevice=hw.Em28xxAudio,0:norm=ntsc:chanlist=us-cable -vf pp=ci
The above command works fine (both audio and video) with my Hauppauge HVR-850, but for the Kworld 305U I must change 'immediatemode=0' to 'immediatemode=1' otherwise the video frame rate is about 1/2 normal speed and about 1 minute later mplayer starts printing 'video buffer full - dropping frame'.
According to dmesg the Kworld 305U loads the same firmware as my Hauppauge HVR-850, and (during separate test sessions) installs the same ALSA device;
card 1: Em28xxAudio [Em28xx Audio], device 0: Em28xx Audio [Empia 28xx Capture]
Subdevices: 0/1
Subdevice #0: subdevice #0
Dean
Re: eb1a:2860 eMPIA em28xx device to usb1 ??? usb hub problem?
Quoted 11 lines · Dean
I am receiving NTSC TV signals. I test with mplayer. Example;
mplayer tv://9 -tv driver=v4l2:alsa:immediatemode=0:adevice=hw.Em28xxAudio,0:norm=ntsc:chanlist=us-cable -vf pp=ci
The above command works fine (both audio and video) with my Hauppauge HVR-850, but for the Kworld 305U I must change 'immediatemode=0' to 'immediatemode=1' otherwise the video frame rate is about 1/2 normal speed and about 1 minute later mplayer starts printing 'video buffer full - dropping frame'.
According to dmesg the Kworld 305U loads the same firmware as my Hauppauge HVR-850, and (during separate test sessions) installs the same ALSA device;
card 1: Em28xxAudio [Em28xx Audio], device 0: Em28xx Audio [Empia 28xx Capture]
Subdevices: 0/1
Subdevice #0: subdevice #0
Try this: open em28xx-cards.c, and change the board profile for the entry EM2880_BOARD_KWORLD_DVB_305U such that it includes the following field:
.mts_firmware = 1,
Then recompile and see if it starts working.
Devin
Signature · 2 lines
Devin J. Heitmueller - Kernel Labs http://www.kernellabs.com