Skip to contentSkip to conversation

net: fec fixes

PATCH In review Amit Kucheria 3 participants 6 messages Feb 5, 2010 – Feb 10, 2010

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

cover net: fec fixes

Some fixes to the fec driver to get it to work on the Freescale i.MX5 SoC platform

Amit Kucheria (2):
fec: Add LAN8700 phy support
fec: Add ARCH_MX5 as a dependency

Rob Herring (1):
fec: fix uninitialized rx buffer usage

 drivers/net/Kconfig |    3 +-
 drivers/net/fec.c   |   78 ++++++++++++++++++++++++++++++++------------------
 2 files changed, 52 insertions(+), 29 deletions(-)
#1 lore raw

PATCH 1/3 fec: fix uninitialized rx buffer usage

From: Rob Herring <[email protected]>

The fec driver was enabling receive buffer descriptor without allocating the buffers. Make sure the buffer descriptors are initialized to not start receiving packets.

Open also calls fec_restart after the rx buffers are allocated. With the code in fec_restart, it zeroes out the buffer descriptors that have just been setup.

---
 drivers/net/fec.c |   57 +++++++++++++++++++++++++++--------------------------
 1 files changed, 29 insertions(+), 28 deletions(-)
drivers/net/fec.c +29 -28
index 16a1d58..9a8743d 100644
@@ -1658,6 +1658,7 @@ static int fec_enet_init(struct net_device *dev, int index)
 {
 	struct fec_enet_private *fep = netdev_priv(dev);
 	struct bufdesc *cbd_base;
+	struct bufdesc *bdp;
 	int i;
 
 	/* Allocate memory for buffer descriptors. */
@@ -1710,6 +1711,34 @@ static int fec_enet_init(struct net_device *dev, int index)
 	/* Set MII speed to 2.5 MHz */
 	fep->phy_speed = ((((clk_get_rate(fep->clk) / 2 + 4999999)
 					/ 2500000) / 2) & 0x3F) << 1;
+
+	/* Initialize the receive buffer descriptors. */
+	bdp = fep->rx_bd_base;
+	for (i = 0; i < RX_RING_SIZE; i++) {
+
+		/* Initialize the BD for every fragment in the page. */
+		bdp->cbd_sc = 0;
+		bdp++;
+	}
+
+	/* Set the last buffer to wrap */
+	bdp--;
+	bdp->cbd_sc |= BD_SC_WRAP;
+
+	/* ...and the same for transmit */
+	bdp = fep->tx_bd_base;
+	for (i = 0; i < TX_RING_SIZE; i++) {
+
+		/* Initialize the BD for every fragment in the page. */
+		bdp->cbd_sc = 0;
+		bdp->cbd_bufaddr = 0;
+		bdp++;
+	}
+
+	/* Set the last buffer to wrap */
+	bdp--;
+	bdp->cbd_sc |= BD_SC_WRAP;
+
 	fec_restart(dev, 0);
 
 	/* Queue up command to detect the PHY and initialize the
@@ -1730,7 +1759,6 @@ static void
 fec_restart(struct net_device *dev, int duplex)
 {
 	struct fec_enet_private *fep = netdev_priv(dev);
-	struct bufdesc *bdp;
 	int i;
 
 	/* Whack a reset.  We should wait for this. */
@@ -1768,33 +1796,6 @@ fec_restart(struct net_device *dev, int duplex)
 		}
 	}
 
-	/* Initialize the receive buffer descriptors. */
-	bdp = fep->rx_bd_base;
-	for (i = 0; i < RX_RING_SIZE; i++) {
-
-		/* Initialize the BD for every fragment in the page. */
-		bdp->cbd_sc = BD_ENET_RX_EMPTY;
-		bdp++;
-	}
-
-	/* Set the last buffer to wrap */
-	bdp--;
-	bdp->cbd_sc |= BD_SC_WRAP;
-
-	/* ...and the same for transmit */
-	bdp = fep->tx_bd_base;
-	for (i = 0; i < TX_RING_SIZE; i++) {
-
-		/* Initialize the BD for every fragment in the page. */
-		bdp->cbd_sc = 0;
-		bdp->cbd_bufaddr = 0;
-		bdp++;
-	}
-
-	/* Set the last buffer to wrap */
-	bdp--;
-	bdp->cbd_sc |= BD_SC_WRAP;
-
 	/* Enable MII mode */
 	if (duplex) {
 		/* MII enable / FD enable */
Signature · 1 line
1.6.3.3
#2 lore raw

PATCH 2/3 fec: Add LAN8700 phy support

The i.MX51 babbage board has a FEC ethernet controller with this phy.

In the long term we should resurrect the phylib patches for fec.

---
 drivers/net/fec.c |   21 +++++++++++++++++++++
 1 files changed, 21 insertions(+), 0 deletions(-)
drivers/net/fec.c +21 -0
index 9a8743d..5d0d332 100644
@@ -1128,6 +1128,26 @@ static phy_info_t phy_info_dp83848= {
 	},
 };
 
+static phy_info_t phy_info_lan8700 = {
+	0x0007C0C,
+	"LAN8700",
+	(const phy_cmd_t []) { /* config */
+		{ mk_mii_read(MII_REG_CR), mii_parse_cr },
+		{ mk_mii_read(MII_REG_ANAR), mii_parse_anar },
+		{ mk_mii_end, }
+	},
+	(const phy_cmd_t []) { /* startup */
+		{ mk_mii_write(MII_REG_CR, 0x1200), NULL }, /* autonegotiate */
+		{ mk_mii_read(MII_REG_SR), mii_parse_sr },
+		{ mk_mii_end, }
+	},
+	(const phy_cmd_t []) { /* act_int */
+		{ mk_mii_end, }
+	},
+	(const phy_cmd_t []) { /* shutdown */
+		{ mk_mii_end, }
+	},
+};
 /* ------------------------------------------------------------------------- */
 
 static phy_info_t const * const phy_info[] = {
@@ -1137,6 +1157,7 @@ static phy_info_t const * const phy_info[] = {
 	&phy_info_am79c874,
 	&phy_info_ks8721bl,
 	&phy_info_dp83848,
+	&phy_info_lan8700,
 	NULL
 };
 
Signature · 1 line
1.6.3.3
#3 lore raw

PATCH 3/3 fec: Add ARCH_MX5 as a dependency

i.MX51 babbage board has a FEC ethernet controller

---
 drivers/net/Kconfig |    3 ++-
 1 files changed, 2 insertions(+), 1 deletions(-)
drivers/net/Kconfig +2 -1
index dd9a09c..515658e 100644
@@ -1883,7 +1883,8 @@ config 68360_ENET
 
 config FEC
 	bool "FEC ethernet controller (of ColdFire and some i.MX CPUs)"
-	depends on M523x || M527x || M5272 || M528x || M520x || M532x || MACH_MX27 || ARCH_MX35 || ARCH_MX25
+	depends on M523x || M527x || M5272 || M528x || M520x || M532x || \
+		MACH_MX27 || ARCH_MX35 || ARCH_MX25 || ARCH_MX5
 	help
 	  Say Y here if you want to use the built-in 10/100 Fast ethernet
 	  controller on some Motorola ColdFire and Freescale i.MX processors.
Signature · 1 line
1.6.3.3
Acked-by on v1 1/3
#4 lore raw

Re: [PATCH 1/3] fec: fix uninitialized rx buffer usage

In reply to Amit Kucheria
Quoted 6 lines · Amit Kucheria

From: Rob Herring <[email protected]>

The fec driver was enabling receive buffer descriptor without allocating the buffers. Make sure the buffer descriptors are initialized to not start receiving packets.

Quoted 7 lines

Open also calls fec_restart after the rx buffers are allocated. With the code in fec_restart, it zeroes out the buffer descriptors that have just been setup.

Quoted 93 lines
---
 drivers/net/fec.c |   57 +++++++++++++++++++++++++++--------------------------
 1 files changed, 29 insertions(+), 28 deletions(-)
drivers/net/fec.c +29 -28
index 16a1d58..9a8743d 100644
@@ -1658,6 +1658,7 @@ static int fec_enet_init(struct net_device *dev, int index)
 {
 	struct fec_enet_private *fep = netdev_priv(dev);
 	struct bufdesc *cbd_base;
+	struct bufdesc *bdp;
 	int i;
 
 	/* Allocate memory for buffer descriptors. */
@@ -1710,6 +1711,34 @@ static int fec_enet_init(struct net_device *dev, int index)
 	/* Set MII speed to 2.5 MHz */
 	fep->phy_speed = ((((clk_get_rate(fep->clk) / 2 + 4999999)
 					/ 2500000) / 2) & 0x3F) << 1;
+
+	/* Initialize the receive buffer descriptors. */
+	bdp = fep->rx_bd_base;
+	for (i = 0; i < RX_RING_SIZE; i++) {
+
+		/* Initialize the BD for every fragment in the page. */
+		bdp->cbd_sc = 0;
+		bdp++;
+	}
+
+	/* Set the last buffer to wrap */
+	bdp--;
+	bdp->cbd_sc |= BD_SC_WRAP;
+
+	/* ...and the same for transmit */
+	bdp = fep->tx_bd_base;
+	for (i = 0; i < TX_RING_SIZE; i++) {
+
+		/* Initialize the BD for every fragment in the page. */
+		bdp->cbd_sc = 0;
+		bdp->cbd_bufaddr = 0;
+		bdp++;
+	}
+
+	/* Set the last buffer to wrap */
+	bdp--;
+	bdp->cbd_sc |= BD_SC_WRAP;
+
 	fec_restart(dev, 0);
 
 	/* Queue up command to detect the PHY and initialize the
@@ -1730,7 +1759,6 @@ static void
 fec_restart(struct net_device *dev, int duplex)
 {
 	struct fec_enet_private *fep = netdev_priv(dev);
-	struct bufdesc *bdp;
 	int i;
 
 	/* Whack a reset.  We should wait for this. */
@@ -1768,33 +1796,6 @@ fec_restart(struct net_device *dev, int duplex)
 		}
 	}
 
-	/* Initialize the receive buffer descriptors. */
-	bdp = fep->rx_bd_base;
-	for (i = 0; i < RX_RING_SIZE; i++) {
-
-		/* Initialize the BD for every fragment in the page. */
-		bdp->cbd_sc = BD_ENET_RX_EMPTY;
-		bdp++;
-	}
-
-	/* Set the last buffer to wrap */
-	bdp--;
-	bdp->cbd_sc |= BD_SC_WRAP;
-
-	/* ...and the same for transmit */
-	bdp = fep->tx_bd_base;
-	for (i = 0; i < TX_RING_SIZE; i++) {
-
-		/* Initialize the BD for every fragment in the page. */
-		bdp->cbd_sc = 0;
-		bdp->cbd_bufaddr = 0;
-		bdp++;
-	}
-
-	/* Set the last buffer to wrap */
-	bdp--;
-	bdp->cbd_sc |= BD_SC_WRAP;
-
 	/* Enable MII mode */
 	if (duplex) {
 		/* MII enable / FD enable */
Signature · 5 lines
------------------------------------------------------------------------
Greg Ungerer  --  Principal Engineer        EMAIL:     [email protected]
SnapGear Group, McAfee                      PHONE:       +61 7 3435 2888
8 Gardner Close                             FAX:         +61 7 3217 5323
Milton, QLD, 4064, Australia                WEB: http://www.SnapGear.com
maintainer
#5 lore raw
In reply to Amit Kucheria

From: Amit Kucheria <[email protected]>
Date: Fri, 5 Feb 2010 10:56:19 -0800

Quoted 9 lines

Some fixes to the fec driver to get it to work on the Freescale i.MX5 SoC platform

Amit Kucheria (2):
fec: Add LAN8700 phy support
fec: Add ARCH_MX5 as a dependency

Rob Herring (1):
fec: fix uninitialized rx buffer usage

All applied to net-next-2.6, thanks.