MX35: Add CUPID board support
Subsystems (3)
PATCH 1/1 MX35: Add CUPID board support
Signed-off-by Carsten Behling <[email protected]>
---
MX35: Add CUPID board support.
arch/arm/mach-mx3/Kconfig | 7 + arch/arm/mach-mx3/Makefile | 1 + arch/arm/mach-mx3/mach-guf_cupid.c | 180 +++++++++++++++++++++++++++ arch/arm/plat-mxc/include/mach/uncompress.h | 1 + 4 files changed, 189 insertions(+), 0 deletions(-) create mode 100644 arch/arm/mach-mx3/mach-guf_cupid.c
arch/arm/mach-mx3/Kconfig +7 -0
@@ -114,4 +114,11 @@ config MACH_KZM_ARM11_01 Include support for KZM-ARM11-01. This includes specific configurations for the board and its peripherals. +config MACH_GUF_CUPID + bool "Support Garz & Fricke Cupid platform" + select ARCH_MX35 + help + Include support for Cupid platform. This includes specific + configurations for the board and its peripherals. + endif
arch/arm/mach-mx3/Makefile +1 -0
@@ -24,3 +24,4 @@ obj-$(CONFIG_MACH_PCM043) += mach-pcm043.o obj-$(CONFIG_MACH_ARMADILLO5X0) += mach-armadillo5x0.o obj-$(CONFIG_MACH_MX35_3DS) += mach-mx35pdk.o obj-$(CONFIG_MACH_KZM_ARM11_01) += mach-kzm_arm11_01.o +obj-$(CONFIG_MACH_GUF_CUPID) += mach-guf_cupid.o
arch/arm/mach-mx3/mach-guf_cupid.c new file +180 -0
180 lines not on this page · raw message
arch/arm/plat-mxc/include/mach/uncompress.h +1 -0
@@ -94,6 +94,7 @@ static __inline__ void __arch_decomp_setup(unsigned long arch_id)case MACH_TYPE_MX35_3DS :case MACH_TYPE_PCM043 :case MACH_TYPE_LILLY1131 : +case MACH_TYPE_GUF_CUPID : uart_base =MX3X_UART1_BASE_ADDR ;break ;case MACH_TYPE_MAGX_ZN5 :
--
1.6.0.2
PATCH 1/1 MX35: Add CUPID board support
Hello Carsten,
Quoted 75 lines · Carsten Behling
Signed-off-by Carsten Behling <[email protected]>---
MX35: Add CUPID board support.arch/arm/mach-mx3/Kconfig | 7 + arch/arm/mach-mx3/Makefile | 1 + arch/arm/mach-mx3/mach-guf_cupid.c | 180 +++++++++++++++++++++++++++ arch/arm/plat-mxc/include/mach/uncompress.h | 1 + 4 files changed, 189 insertions(+), 0 deletions(-) create mode 100644 arch/arm/mach-mx3/mach-guf_cupid.carch/arm/mach-mx3/Kconfig +7
-0@@ -114,4 +114,11 @@ config MACH_KZM_ARM11_01 Include support for KZM-ARM11-01. This includes specific configurations for the board and its peripherals. +config MACH_GUF_CUPID + bool "Support Garz & Fricke Cupid platform" + select ARCH_MX35 + help + Include support for Cupid platform. This includes specific + configurations for the board and its peripherals. + endifarch/arm/mach-mx3/Makefile +1
-0@@ -24,3 +24,4 @@ obj-$(CONFIG_MACH_PCM043) += mach-pcm043.o obj-$(CONFIG_MACH_ARMADILLO5X0) += mach-armadillo5x0.o obj-$(CONFIG_MACH_MX35_3DS) += mach-mx35pdk.o obj-$(CONFIG_MACH_KZM_ARM11_01) += mach-kzm_arm11_01.o +obj-$(CONFIG_MACH_GUF_CUPID) += mach-guf_cupid.oarch/arm/mach-mx3/mach-guf_cupid.c new file +33
-0@@ -0,0 +1,180 @@ +/* +* Copyright 2010 Garz & Fricke GmbH All Rights Reserved. +* +* Author: Carsten Behling <[email protected]> +* +* This program is free software; you can redistribute it and/or modify +* it under the terms of the GNU General Public License as published by +* the Free Software Foundation; either version 2 of the License, or +* (at your option) any later version. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +* GNU General Public License for more details. +* +* You should have received a copy of the GNU General Public License +* along with this program; if not, write to the Free Software +* Foundation, Inc., 51 Franklin Street, Fifth Floor Boston, MA 02110-1301 USA +*/ + +#include <linux/types.h> +#include <linux/init.h> +#include <linux/platform_device.h> +#include <linux/mtd/physmap.h> +#include <linux/memory.h> +#include <linux/interrupt.h> +#include <linux/delay.h> + +#include <asm/mach-types.h> +#include <asm/mach/arch.h> +#include <asm/mach/time.h> +#include <asm/mach/map.h> +#include <mach/hardware.h>
arch/arm/mach-mx3/mach-guf_cupid.c line 43
Quoted 10 lines
arch/arm/mach-mx3/mach-guf_cupid.c new file +10
-0+#include <mach/common.h> +#include <mach/imx-uart.h> +#include <mach/iomux-mx35.h> +#include <mach/ipu.h> +#include <mach/mx3fb.h> +#include <mach/mxc_nand.h> + +#include "devices.h" + +static struct fb_videomode fb_modedb[] = {
The kernel image works fine with that name, but IMHO it makes editing a bit easier, if all symbols (even static ones) have a nice prefix. There are already four variables with that name. Ditto for the other variables (e.g. there are currently 8 functions called mxc_board_init).
Quoted 127 lines
arch/arm/mach-mx3/mach-guf_cupid.c new file +127
-0+ { +/* 800x480 @ 70 Hz */ + .name = "CPT CLAA070LC0JCT", + .refresh = 70, + .xres = 800, + .yres = 480, + .pixclock = 30761, + .left_margin = 24, + .right_margin = 47, + .upper_margin = 5, + .lower_margin = 3, + .hsync_len = 24, + .vsync_len = 3, + .sync =FB_SYNC_HOR_HIGH_ACT |FB_SYNC_SHARP_MODE | + FB_SYNC_CLK_INVERT | FB_SYNC_CLK_IDLE_EN, + .vmode = FB_VMODE_NONINTERLACED, + .flag = 0, + }, +}; + +static struct ipu_platform_data mx3_ipu_data = { + .irq_base =MXC_IPU_IRQ_START , +}; + +static struct mx3fb_platform_data mx3fb_pdata = { + .dma_dev = &mx3_ipu.dev, + .name ="CPT CLAA070LC0JCT" , + .mode = fb_modedb, + .num_modes =ARRAY_SIZE (fb_modedb), +}; + +static struct imxuart_platform_data uart_pdata = { + .flags =IMXUART_HAVE_RTSCTS , +}; + +static struct platform_device *devices[]__initdata = { + &mxc_fec_device, +}; + +static struct pad_desc cupid_pads[] = { +/* UART1 */ +MX35_PAD_CTS1__UART1_CTS , +MX35_PAD_RTS1__UART1_RTS , +MX35_PAD_TXD1__UART1_TXD_MUX , +MX35_PAD_RXD1__UART1_RXD_MUX , +/* UART2 */ +MX35_PAD_CTS2__UART2_CTS , +MX35_PAD_RTS2__UART2_RTS , +MX35_PAD_TXD2__UART2_TXD_MUX , +MX35_PAD_RXD2__UART2_RXD_MUX , +/* FEC */ +MX35_PAD_FEC_TX_CLK__FEC_TX_CLK , +MX35_PAD_FEC_RX_CLK__FEC_RX_CLK , +MX35_PAD_FEC_RX_DV__FEC_RX_DV , +MX35_PAD_FEC_COL__FEC_COL , +MX35_PAD_FEC_RDATA0__FEC_RDATA_0 , +MX35_PAD_FEC_TDATA0__FEC_TDATA_0 , +MX35_PAD_FEC_TX_EN__FEC_TX_EN , +MX35_PAD_FEC_MDC__FEC_MDC , +MX35_PAD_FEC_MDIO__FEC_MDIO , +MX35_PAD_FEC_TX_ERR__FEC_TX_ERR , +MX35_PAD_FEC_RX_ERR__FEC_RX_ERR , +MX35_PAD_FEC_CRS__FEC_CRS , +MX35_PAD_FEC_RDATA1__FEC_RDATA_1 , +MX35_PAD_FEC_TDATA1__FEC_TDATA_1 , +MX35_PAD_FEC_RDATA2__FEC_RDATA_2 , +MX35_PAD_FEC_TDATA2__FEC_TDATA_2 , +MX35_PAD_FEC_RDATA3__FEC_RDATA_3 , +MX35_PAD_FEC_TDATA3__FEC_TDATA_3 , +/* Display */ +MX35_PAD_LD0__IPU_DISPB_DAT_0 , +MX35_PAD_LD1__IPU_DISPB_DAT_1 , +MX35_PAD_LD2__IPU_DISPB_DAT_2 , +MX35_PAD_LD3__IPU_DISPB_DAT_3 , +MX35_PAD_LD4__IPU_DISPB_DAT_4 , +MX35_PAD_LD5__IPU_DISPB_DAT_5 , +MX35_PAD_LD6__IPU_DISPB_DAT_6 , +MX35_PAD_LD7__IPU_DISPB_DAT_7 , +MX35_PAD_LD8__IPU_DISPB_DAT_8 , +MX35_PAD_LD9__IPU_DISPB_DAT_9 , +MX35_PAD_LD10__IPU_DISPB_DAT_10 , +MX35_PAD_LD11__IPU_DISPB_DAT_11 , +MX35_PAD_LD12__IPU_DISPB_DAT_12 , +MX35_PAD_LD13__IPU_DISPB_DAT_13 , +MX35_PAD_LD14__IPU_DISPB_DAT_14 , +MX35_PAD_LD15__IPU_DISPB_DAT_15 , +MX35_PAD_LD16__IPU_DISPB_DAT_16 , +MX35_PAD_LD17__IPU_DISPB_DAT_17 , +MX35_PAD_D3_HSYNC__IPU_DISPB_D3_HSYNC , +MX35_PAD_D3_FPSHIFT__IPU_DISPB_D3_CLK , +MX35_PAD_D3_DRDY__IPU_DISPB_D3_DRDY , +MX35_PAD_D3_VSYNC__IPU_DISPB_D3_VSYNC , +MX35_PAD_LD18__GPIO3_24 ,/* LCD enable */ +}; + +static struct mxc_nand_platform_data nand_pdata = { + .width =1 , + .hw_ecc =1 , + .flash_bbt =0 , +}; + +/* +* Board specific initialization. +*/ +static void __init mxc_board_init (void ) +{ +mxc_iomux_v3_setup_multiple_pads (cupid_pads,ARRAY_SIZE (cupid_pads)); + +platform_add_devices (devices,ARRAY_SIZE (devices)); + +mxc_register_device (&mxc_uart_device0, &uart_pdata); +mxc_register_device (&mxc_uart_device1, &uart_pdata); +mxc_register_device (&mxc_nand_device, &nand_pdata); +mxc_register_device (&mx3_ipu, &mx3_ipu_data); +mxc_register_device (&mx3_fb, &mx3fb_pdata); +} + +static void __init cupid_timer_init (void ) +{ +mx35_clocks_init (); +} + +struct sys_timer cupid_timer = { + .init = cupid_timer_init, +}; + +MACHINE_START (GUF_CUPID ,"Garz & Fricke CUPID" )
arch/arm/mach-mx3/mach-guf_cupid.c line 180
Quoted 10 lines
arch/arm/mach-mx3/mach-guf_cupid.c new file +10
-0+/* Maintainer: Garz & Fricke GmbH */ + .phys_io = MX35_AIPS1_BASE_ADDR, + .io_pg_offst = ((MX35_AIPS1_BASE_ADDR_VIRT) >> 18) & 0xfffc, + .boot_params = MX3x_PHYS_OFFSET + 0x100, + .map_io = mx35_map_io, + .init_irq = mx35_init_irq, + .init_machine = mxc_board_init, + .timer = &cupid_timer, +MACHINE_END +
trailing newline
Quoted 13 lines
arch/arm/plat-mxc/include/mach/uncompress.h +1
-1@@ -94,6 +94,7 @@ static __inline__ void __arch_decomp_setup(unsigned long arch_id)case MACH_TYPE_MX35_3DS :case MACH_TYPE_PCM043 :case MACH_TYPE_LILLY1131 : +case MACH_TYPE_GUF_CUPID : uart_base =MX3X_UART1_BASE_ADDR ;break ;case MACH_TYPE_MAGX_ZN5 : --
Quoted 1 line
1.6.0.2
Best regards
Uwe
Signature · 2 lines
Pengutronix e.K. | Uwe Kleine-K?nig | Industrial Linux Solutions | http://www.pengutronix.de/ |