Hi guys, maybe this is not the best list but I ask about my problem
I'm developing a custom board (designed by me) based on sh2a 7203 (Renesas). I have some troubles with my SST flash, while I'm sure my eth0 card works. For building my rootfs I use a script
Im able to mount the nfsroot filesystem but I get this message:
IP-Config: Complete:
device=eth0, addr=192.168.1.3, mask=255.255.255.0, gw=192.168.1.254,
host=uclinux, domain=, nis-domain=(none),
bootserver=192.168.1.2, rootserver=192.168.1.2, rootpath=Looking up port of RPC 100003/3 on 192.168.1.2
Looking up port of RPC 100005/3 on 192.168.1.2
do_mount_root,270 - debug 1/dev/root,0x0c1a58a0,0x00008000,0x0c24659c
do_mount_root,273 - debug 2
do_mount_root,277 - debug 3
do_mount_root,279 - debug 4
VFS: Mounted root (nfs filesystem).
Freeing unused kernel memory: 88k freed
Warning: unable to open an initial console.
Kernel panic - not syncing: No init found. Try passing init= option to
kernel.
In rootpath I should read someting?
Could the problem be my PC is little endian and I' exporting to a big endian CPU?
Thanks in advance.
Signature · 7 lines
Fabio Giovagnini Aurion s.r.l. P.I e C.F. 00885711200 Tel. +39.051.594.78.24 Cell. +39.335.83.50.919
Dear Fabio Giovagnini,
you are indeed completely off topic here on the U-Boot list.
Quoted 2 lines · In message <[email protected]> you wrote:
Im able to mount the nfsroot filesystem but I get this message:
...
Quoted 1 line
Warning: unable to open an initial console.
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Quoted 1 line
In rootpath I should read someting?
You should read the error messages and contemplate their meaning.
Quoted 2 lines
Could the problem be my PC is little endian and I' exporting to a big endian CPU?
No.
"unable to open an initial console" usually means that there is no "/dev/console" entry in your root file system, so check your root file system if it is complete.
[If you were using the ELDK, my bet was that you have forgotten to run the ELDK_MAKEDEV (plus eventually the ELDK_FIXOWNER) script(s), but you don't include such vital information as where this root file system is coming from and why you think it should be a working one.]
Best regards,
Wolfgang Denk
Signature · 4 lines
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de Quantum particles: The dreams that stuff is made of.
Thanks alot.
The very first problem was a permission problem, as you suggestied to ckech. But now I think a Have a problem of irq losing form eth.
Thanks again
In data gioved? 18 marzo 2010 09:04:22, Wolfgang Denk ha scritto:
: > Dear Fabio Giovagnini,
Quoted 34 lines
you are indeed completely off topic here on the U-Boot list.
Quoted 1 line · In message <[email protected]> you wrote:
Im able to mount the nfsroot filesystem but I get this message:
...
Quoted 1 line
Warning: unable to open an initial console.
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Quoted 1 line
In rootpath I should read someting?
You should read the error messages and contemplate their meaning.
Quoted 2 lines
Could the problem be my PC is little endian and I' exporting to a big endian CPU?
No.
"unable to open an initial console" usually means that there is no "
/dev/console" entry in your root file system, so check your root file system if it is complete.[If you were using the ELDK, my bet was that you have forgotten to run the
ELDK_MAKEDEV(plus eventually theELDK_FIXOWNER) script(s), but you don't include such vital information as where this root file system is coming from and why you think it should be a working one.]Best regards,
Wolfgang Denk
Signature · 7 lines
Fabio Giovagnini Aurion s.r.l. P.I e C.F. 00885711200 Tel. +39.051.594.78.24 Cell. +39.335.83.50.919