tty: n_gsm line discipline
Subsystems (2)
RFC PATCH 1/1 tty: n_gsm line discipline
Add an implementation of GSM 0710 MUX. The implementation currently supports
- Basic and advanced framing (as either end of the link)
- UI or UIH data frames
- Adaption layer 1-4 (1 and 2 via tty, 3 and 4 as skbuff lists)
- Modem and control messages including the correct retry process
- Flow control
and exposes the MUX channels as a set of virtual tty devices including modem signals.
This is a development patch, but I wanted to get public visibility and also a chance for people to test this with other devices.
You may also ask "why in kernel" - well there are three good reasons
- Lots of complex locking and timer handling between channels
- Channels affect each other (eg DLCI 0 is control for other bits)
- Performance - on a 3G setup you may be running a 10Mbit plus and we will want to tap DLCI channels directly into the kernel networking, which means we need to demux kernel side.
As a side effect we also get a convenient interface where things like pppd, phone sim tools, sms software and minicom 'just work' on AT mode logical channels.
---
drivers/char/Kconfig | 8 drivers/char/Makefile | 1 drivers/char/n_gsm.c | 2768 ++++++++++++++++++++++++++++++++++++++++++++++++ include/linux/gsmmux.h | 23 include/linux/tty.h | 5 5 files changed, 2802 insertions(+), 3 deletions(-) create mode 100644 drivers/char/n_gsm.c create mode 100644 include/linux/gsmmux.h
drivers/char/Kconfig +7 -1
@@ -276,11 +276,17 @@ config N_HDLC Allows synchronous HDLC communications with tty device drivers that support synchronous HDLC such as the Microgate SyncLink adapter. - This driver can only be built as a module ( = code which can be + This driver can be built as a module ( = code which can be inserted in and removed from the running kernel whenever you want). The module will be called n_hdlc. If you want to do that, say M here. +config N_GSM + tristate "GSM MUX line discipline support" + help + This line discipline provides support for the GSM MUX protocol and + presents the mux as a set of 61 individual tty devices. + config RISCOM8 tristate "SDL RISCom/8 card support" depends on SERIAL_NONSTANDARD
drivers/char/Makefile +1 -0
@@ -41,6 +41,7 @@ obj-$(CONFIG_SYNCLINK) += synclink.o obj-$(CONFIG_SYNCLINKMP) += synclinkmp.o obj-$(CONFIG_SYNCLINK_GT) += synclink_gt.o obj-$(CONFIG_N_HDLC) += n_hdlc.o +obj-$(CONFIG_N_GSM) += n_gsm.o obj-$(CONFIG_AMIGA_BUILTIN_SERIAL) += amiserial.o obj-$(CONFIG_SX) += sx.o generic_serial.o obj-$(CONFIG_RIO) += rio/ generic_serial.o
drivers/char/n_gsm.c new file +2768 -0
2,768 lines not on this page · raw message
include/linux/gsmmux.h new file +23 -0
@@ -0,0 +1,23 @@ +#ifndef _LINUX_GSMMUX_H +#define _LINUX_GSMMUX_H + +struct gsm_config +{ +unsigned int adaption; +unsigned int encapsulation; +unsigned int initiator; +unsigned int t1; +unsigned int t2; +unsigned int t3; +unsigned int n2; +unsigned int mru; +unsigned int mtu; +unsigned int k; +unsigned int i; +}; + +#define GSMIOC_GETCONF _IOR('G', 0, struct gsm_config) +#define GSMIOC_SETCONF _IOW('G', 1, struct gsm_config) + + +#endif
include/linux/tty.h +3 -2
@@ -23,7 +23,7 @@*/ #define NR_UNIX98_PTY_DEFAULT 4096/* Default maximum for Unix98 ptys */ #define NR_UNIX98_PTY_MAX (1 << MINORBITS)/* Absolute limit */ -#define NR_LDISCS 20 +#define NR_LDISCS 21/* line disciplines */ #define N_TTY 0
@@ -46,8 +46,9 @@#define N_GIGASET_M101 16/* Siemens Gigaset M101 serial DECT adapter */ #define N_SLCAN 17/* Serial / USB serial CAN Adaptors */ #define N_PPS 18/* Pulse per Second */ -#define N_V253 19/* Codec control over voice modem */ +#define N_GSM0710 20/* GSM 0710 Mux */ +/* * This character is the same as _POSIX_VDISABLE: it cannot be used as