Fix default state Beholder H6 tuner.
PATCH 1/1 Fix default state Beholder H6 tuner.
Hi
The hybrid tuner FMD1216MEX_MK3 after cold start has disabled IF.
This tuner has internal I2C switch. This switch switch I2C bus between DVB-T and IF part. Default state is DVB-T. When module saa7134 is load it can't find IF tda9887 and disable analog TV mode.
This patch set internal I2C switch of the tuner to IF by send special value to the tuner as for receive analog TV from low band. It can be usefule for other cards.
I didn't set configure a tuner by a tuner model because this tuner can has different I2C address. May be we can do it later after discuss for more robust support a tuners.
linux/drivers/media/video/saa7134/saa7134-cards.c +17 -0
@@ -7450,6 +7450,21 @@ }break ; } +case SAA7134_BOARD_BEHOLD_H6 : + { +u8 data[] = {0x09 ,0x9f ,0x86 ,0x11 }; +struct i2c_msg msg = {.addr =0x61 , .flags =0 , .buf = data, + .len =sizeof (data)}; + +/* The tuner TUNER_PHILIPS_FMD1216MEX_MK3 after hardware */ +/* start has disabled IF and enabled DVB-T. When saa7134 */ +/* scan I2C devices it not detect IF tda9887 and can`t */ +/* watch TV without software reboot. For solve this problem */ +/* switch the tuner to analog TV mode manually. */ +if (i2c_transfer (&dev->i2c_adap, &msg,1 ) !=1 ) +printk (KERN_WARNING +"%s: Unable to enable IF of the tuner.\n" , + dev->name); +break ; + } }/* switch() */
/* initialize tuner */
With my best regards, Dmitry.
linux/drivers/media/video/saa7134/saa7134-cards.c +17 -0
@@ -7450,6 +7450,21 @@ }break ; } +case SAA7134_BOARD_BEHOLD_H6 : + { +u8 data[] = {0x09 ,0x9f ,0x86 ,0x11 }; +struct i2c_msg msg = {.addr =0x61 , .flags =0 , .buf = data, + .len =sizeof (data)}; + +/* The tuner TUNER_PHILIPS_FMD1216MEX_MK3 after hardware */ +/* start has disabled IF and enabled DVB-T. When saa7134 */ +/* scan I2C devices it not detect IF tda9887 and can`t */ +/* watch TV without software reboot. For solve this problem */ +/* switch the tuner to analog TV mode manually. */ +if (i2c_transfer (&dev->i2c_adap, &msg,1 ) !=1 ) +printk (KERN_WARNING +"%s: Unable to enable IF of the tuner.\n" , + dev->name); +break ; + } }/* switch() */
/* initialize tuner */
Hi,
Am Dienstag, den 30.03.2010, 16:02 +1000 schrieb Dmitri Belimov:
Quoted 7 lines
Hi
The hybrid tuner
FMD1216MEX_MK3after cold start has disabled IF.
This tuner has internal I2C switch. This switch switch I2C bus between DVB-T and IF part. Default state is DVB-T. When module saa7134 is load it can't find IF tda9887 and disable analog TV mode.
Quoted 5 lines
This patch set internal I2C switch of the tuner to IF by send special value to the tuner as for receive analog TV from low band. It can be usefule for other cards.
I didn't set configure a tuner by a tuner model because this tuner can has different I2C address. May be we can do it later after discuss for more robust support a tuners.
just as a reminder. It is the same for the FMD1216ME hybrid MK3. After every boot, analog mode fails with missing tda9887.
Currently, after tuner modules are not independent anymore, one has to reload the saa7134 driver once.
Relevant code in tuner.core.c.
case TUNER_PHILIPS_FMD1216ME_MK3: buffer[0] = 0x0b; buffer[1] = 0xdc; buffer[2] = 0x9c; buffer[3] = 0x60; i2c_master_send(c, buffer, 4); mdelay(1); buffer[2] = 0x86; buffer[3] = 0x54; i2c_master_send(c, buffer, 4); if (!dvb_attach(simple_tuner_attach, &t->fe, t->i2c->adapter, t->i2c->addr, t->type)) goto attach_failed; break;
Hermann
Quoted 31 lines
diff -r
1ef0265456c8linux/drivers/media/video/saa7134/saa7134-cards.clinux/drivers/media/video/saa7134/saa7134-cards.c +17
-0@@ -7450,6 +7450,21 @@ }break ; } +case SAA7134_BOARD_BEHOLD_H6 : + { +u8 data[] = {0x09 ,0x9f ,0x86 ,0x11 }; +struct i2c_msg msg = {.addr =0x61 , .flags =0 , .buf = data, + .len =sizeof (data)}; + +/* The tuner TUNER_PHILIPS_FMD1216MEX_MK3 after hardware */ +/* start has disabled IF and enabled DVB-T. When saa7134 */ +/* scan I2C devices it not detect IF tda9887 and can`t */ +/* watch TV without software reboot. For solve this problem */ +/* switch the tuner to analog TV mode manually. */ +if (i2c_transfer (&dev->i2c_adap, &msg,1 ) !=1 ) +printk (KERN_WARNING +"%s: Unable to enable IF of the tuner.\n" , + dev->name); +break ; + } }/* switch() */ /* initialize tuner */ Signed-off-by Beholder Intl. Ltd. Dmitry Belimov <[email protected]>With my best regards, Dmitry.
Hi Hermann
Quoted 26 lines
Hi,
Am Dienstag, den 30.03.2010, 16:02 +1000 schrieb Dmitri Belimov:
Quoted 7 lines
Hi
The hybrid tuner
FMD1216MEX_MK3after cold start has disabled IF. This tuner has internal I2C switch. This switch switch I2C bus between DVB-T and IF part. Default state is DVB-T. When module saa7134 is load it can't find IF tda9887 and disable analog TV mode.Quoted 7 lines
This patch set internal I2C switch of the tuner to IF by send special value to the tuner as for receive analog TV from low band. It can be usefule for other cards.
I didn't set configure a tuner by a tuner model because this tuner can has different I2C address. May be we can do it later after discuss for more robust support a tuners.
just as a reminder. It is the same for the FMD1216ME hybrid MK3. After every boot, analog mode fails with missing tda9887.
Currently, after tuner modules are not independent anymore, one has to reload the saa7134 driver once.
Relevant code in
tuner.core.c.
Quoted 14 lines
case TUNER_PHILIPS_FMD1216ME_MK3: buffer[0] = 0x0b; buffer[1] = 0xdc; buffer[2] = 0x9c; buffer[3] = 0x60; i2c_master_send(c, buffer, 4); mdelay(1); buffer[2] = 0x86; buffer[3] = 0x54; i2c_master_send(c, buffer, 4); if (!dvb_attach(simple_tuner_attach, &t->fe, t->i2c->adapter, t->i2c->addr, t->type)) goto attach_failed; break;
That is good. I'll try add case TUNER_PHILIPS_FMD1216MEX_MK3 here and test. This is much better.
With my best regards, Dmitry.
Quoted 42 lines
Hermann
Quoted 39 lines
diff -r
1ef0265456c8linux/drivers/media/video/saa7134/saa7134-cards.c---a/linux/drivers/media/video/saa7134/saa7134-cards.cFri Mar
26 00:54:18 2010 -0300 +++b/linux/drivers/media/video/saa7134/saa7134-cards.cSun Mar
28 08:21:10 2010 -0400 @@ -7450,6 +7450,21 @@ } break;linux/drivers/media/video/saa7134/saa7134-cards.c +4
-0} +case SAA7134_BOARD_BEHOLD_H6 : + { + u8 data[] = { 0x09, 0x9f, 0x86, 0x11}; + struct i2c_msg msg = {.addr = 0x61, .flags =0, .buf = data,
(quoted diff) +1
-0+ .len =sizeof(data)}; +
(quoted diff) +1
-0+ /* The tuner TUNER_PHILIPS_FMD1216MEX_MK3 afterhardware */
(quoted diff) +1
-0+ /* start has disabled IF and enabled DVB-T. Whensaa7134 */
(quoted diff) +1
-0+ /* scan I2C devices it not detect IF tda9887 andcan`t */
(quoted diff) +1
-0+ /* watch TV without software reboot. For solvethis problem */
(quoted diff) +1
-0+ /* switch the tuner to analog TV modemanually. */
linux/drivers/media/video/saa7134/saa7134-cards.c +3
-0+if (i2c_transfer (&dev->i2c_adap, &msg,1 ) !=1 ) +printk (KERN_WARNING + "%s: Unable to enable IF ofthe tuner.\n",
linux/drivers/media/video/saa7134/saa7134-cards.c +3
-0+ dev->name); +break ; + } }/* switch() */ /* initialize tuner */ Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov
<[email protected]>With my best regards, Dmitry.
Hi Dimitry,
Am Mittwoch, den 31.03.2010, 13:14 +1000 schrieb Dmitri Belimov:
Quoted 43 lines
Hi Hermann
Quoted 26 lines
Hi,
Am Dienstag, den 30.03.2010, 16:02 +1000 schrieb Dmitri Belimov:
Quoted 7 lines
Hi
The hybrid tuner
FMD1216MEX_MK3after cold start has disabled IF. This tuner has internal I2C switch. This switch switch I2C bus between DVB-T and IF part. Default state is DVB-T. When module saa7134 is load it can't find IF tda9887 and disable analog TV mode.Quoted 7 lines
This patch set internal I2C switch of the tuner to IF by send special value to the tuner as for receive analog TV from low band. It can be usefule for other cards.
I didn't set configure a tuner by a tuner model because this tuner can has different I2C address. May be we can do it later after discuss for more robust support a tuners.
just as a reminder. It is the same for the FMD1216ME hybrid MK3. After every boot, analog mode fails with missing tda9887.
Currently, after tuner modules are not independent anymore, one has to reload the saa7134 driver once.
Relevant code in
tuner.core.c.Quoted 14 lines
case TUNER_PHILIPS_FMD1216ME_MK3: buffer[0] = 0x0b; buffer[1] = 0xdc; buffer[2] = 0x9c; buffer[3] = 0x60; i2c_master_send(c, buffer, 4); mdelay(1); buffer[2] = 0x86; buffer[3] = 0x54; i2c_master_send(c, buffer, 4); if (!dvb_attach(simple_tuner_attach, &t->fe, t->i2c->adapter, t->i2c->addr, t->type)) goto attach_failed; break;
Quoted 2 lines
That is good. I'll try add case
TUNER_PHILIPS_FMD1216MEX_MK3here and test. This is much better.
it wont work for any what I can tell.
We were forced into such an universal looking solution, but it was broken only a short time later.
I for sure don't say that this time, late 2005, it was in anyway perfect, too much random on module load orders and also duplicate address stuff around meanwhile.
But, however, it seems to be blocked for a global attempt within the current schemes too.
Cheers,
Hermann
Quoted 44 lines
With my best regards, Dmitry.
Quoted 42 lines
Hermann
Quoted 39 lines
diff -r
1ef0265456c8linux/drivers/media/video/saa7134/saa7134-cards.c---a/linux/drivers/media/video/saa7134/saa7134-cards.cFri Mar
26 00:54:18 2010 -0300 +++b/linux/drivers/media/video/saa7134/saa7134-cards.cSun Mar
28 08:21:10 2010 -0400 @@ -7450,6 +7450,21 @@ } break;linux/drivers/media/video/saa7134/saa7134-cards.c +4
-0} +case SAA7134_BOARD_BEHOLD_H6 : + { + u8 data[] = { 0x09, 0x9f, 0x86, 0x11}; + struct i2c_msg msg = {.addr = 0x61, .flags =0, .buf = data,
(quoted diff) +1
-0+ .len =sizeof(data)}; +
(quoted diff) +1
-0+ /* The tuner TUNER_PHILIPS_FMD1216MEX_MK3 afterhardware */
(quoted diff) +1
-0+ /* start has disabled IF and enabled DVB-T. Whensaa7134 */
(quoted diff) +1
-0+ /* scan I2C devices it not detect IF tda9887 andcan`t */
(quoted diff) +1
-0+ /* watch TV without software reboot. For solvethis problem */
(quoted diff) +1
-0+ /* switch the tuner to analog TV modemanually. */
linux/drivers/media/video/saa7134/saa7134-cards.c +3
-0+if (i2c_transfer (&dev->i2c_adap, &msg,1 ) !=1 ) +printk (KERN_WARNING + "%s: Unable to enable IF ofthe tuner.\n",
linux/drivers/media/video/saa7134/saa7134-cards.c +3
-0+ dev->name); +break ; + } }/* switch() */ /* initialize tuner */ Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov
<[email protected]>With my best regards, Dmitry.
Hi Hermann
Quoted 55 lines
Hi Dimitry,
Am Mittwoch, den 31.03.2010, 13:14 +1000 schrieb Dmitri Belimov:
Quoted 44 lines
Hi Hermann
Quoted 27 lines
Hi,
Am Dienstag, den 30.03.2010, 16:02 +1000 schrieb Dmitri Belimov:
Quoted 8 lines
Hi
The hybrid tuner
FMD1216MEX_MK3after cold start has disabled IF. This tuner has internal I2C switch. This switch switch I2C bus between DVB-T and IF part. Default state is DVB-T. When module saa7134 is load it can't find IF tda9887 and disable analog TV mode.Quoted 7 lines
This patch set internal I2C switch of the tuner to IF by send special value to the tuner as for receive analog TV from low band. It can be usefule for other cards.
I didn't set configure a tuner by a tuner model because this tuner can has different I2C address. May be we can do it later after discuss for more robust support a tuners.
just as a reminder. It is the same for the FMD1216ME hybrid MK3. After every boot, analog mode fails with missing tda9887.
Currently, after tuner modules are not independent anymore, one has to reload the saa7134 driver once.
Relevant code in
tuner.core.c.Quoted 14 lines
case TUNER_PHILIPS_FMD1216ME_MK3: buffer[0] = 0x0b; buffer[1] = 0xdc; buffer[2] = 0x9c; buffer[3] = 0x60; i2c_master_send(c, buffer, 4); mdelay(1); buffer[2] = 0x86; buffer[3] = 0x54; i2c_master_send(c, buffer, 4); if (!dvb_attach(simple_tuner_attach, &t->fe, t->i2c->adapter, t->i2c->addr, t->type)) goto attach_failed; break;Quoted 2 lines
That is good. I'll try add case
TUNER_PHILIPS_FMD1216MEX_MK3here and test. This is much better.it wont work for any what I can tell.
We were forced into such an universal looking solution, but it was broken only a short time later.
Quoted 6 lines
I for sure don't say that this time, late 2005, it was in anyway perfect, too much random on module load orders and also duplicate address stuff around meanwhile.
But, however, it seems to be blocked for a global attempt within the current schemes too.
Yes. Not worked. My patch is good for our customers right now. But when this subsystem is ready we can switch to use it.
With my best regards, Dmitry.
Quoted 48 lines
Cheers,
HermannQuoted 44 lines
With my best regards, Dmitry.
Quoted 42 lines
Hermann
Quoted 39 lines
diff -r
1ef0265456c8linux/drivers/media/video/saa7134/saa7134-cards.c---a/linux/drivers/media/video/saa7134/saa7134-cards.cFriMar 26 00:54:18 2010 -0300 +++ b/linux/drivers/media/video/saa7134/saa7134-cards.c Sun Mar 28 08:21:10 2010 -0400 @@ -7450,6 +7450,21 @@ } break;linux/drivers/media/video/saa7134/saa7134-cards.c +4
-0} +case SAA7134_BOARD_BEHOLD_H6 : + { + u8 data[] = { 0x09, 0x9f, 0x86, 0x11}; + struct i2c_msg msg = {.addr = 0x61, .flags =0, .buf = data,
(quoted diff) +1
-0+ .len =sizeof(data)}; +
(quoted diff) +1
-0+ /* The tuner TUNER_PHILIPS_FMD1216MEX_MK3 afterhardware */
(quoted diff) +1
-0+ /* start has disabled IF and enabled DVB-T.When saa7134 */
(quoted diff) +1
-0+ /* scan I2C devices it not detect IF tda9887and can`t */
(quoted diff) +1
-0+ /* watch TV without software reboot. For solvethis problem */
(quoted diff) +1
-0+ /* switch the tuner to analog TV modemanually. */
linux/drivers/media/video/saa7134/saa7134-cards.c +3
-0+if (i2c_transfer (&dev->i2c_adap, &msg,1 ) !=1 ) +printk (KERN_WARNING + "%s: Unable to enable IFof the tuner.\n",
linux/drivers/media/video/saa7134/saa7134-cards.c +3
-0+ dev->name); +break ; + } }/* switch() */ /* initialize tuner */ Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov
<[email protected]>With my best regards, Dmitry.
Em 01-04-2010 01:33, Dmitri Belimov escreveu:
Quoted 61 lines
Hi Hermann
Quoted 59 lines
Hi Dimitry,
Am Mittwoch, den 31.03.2010, 13:14 +1000 schrieb Dmitri Belimov:
Quoted 44 lines
Hi Hermann
Quoted 27 lines
Hi,
Am Dienstag, den 30.03.2010, 16:02 +1000 schrieb Dmitri Belimov:
Quoted 8 lines
Hi
The hybrid tuner
FMD1216MEX_MK3after cold start has disabled IF. This tuner has internal I2C switch. This switch switch I2C bus between DVB-T and IF part. Default state is DVB-T. When module saa7134 is load it can't find IF tda9887 and disable analog TV mode.Quoted 7 lines
This patch set internal I2C switch of the tuner to IF by send special value to the tuner as for receive analog TV from low band. It can be usefule for other cards.
I didn't set configure a tuner by a tuner model because this tuner can has different I2C address. May be we can do it later after discuss for more robust support a tuners.
just as a reminder. It is the same for the FMD1216ME hybrid MK3. After every boot, analog mode fails with missing tda9887.
Currently, after tuner modules are not independent anymore, one has to reload the saa7134 driver once.
Relevant code in
tuner.core.c.Quoted 14 lines
case TUNER_PHILIPS_FMD1216ME_MK3: buffer[0] = 0x0b; buffer[1] = 0xdc; buffer[2] = 0x9c; buffer[3] = 0x60; i2c_master_send(c, buffer, 4); mdelay(1); buffer[2] = 0x86; buffer[3] = 0x54; i2c_master_send(c, buffer, 4); if (!dvb_attach(simple_tuner_attach, &t->fe, t->i2c->adapter, t->i2c->addr, t->type)) goto attach_failed; break;Quoted 2 lines
That is good. I'll try add case
TUNER_PHILIPS_FMD1216MEX_MK3here and test. This is much better.it wont work for any what I can tell.
We were forced into such an universal looking solution, but it was broken only a short time later.
I for sure don't say that this time, late 2005, it was in anyway perfect, too much random on module load orders and also duplicate address stuff around meanwhile.
Quoted 8 lines
Quoted 2 lines
But, however, it seems to be blocked for a global attempt within the current schemes too.
Yes. Not worked. My patch is good for our customers right now. But when this subsystem is ready we can switch to use it.
With my best regards, Dmitry.
I'll apply the patch for now, but the better is to fix the TUNER_PHILIPS_FMD1216MEX_MK3.
Dmitri, could you please try to fix it with a more generic solution?
Thanks,
Mauro
Hi Mauro
Quoted 68 lines
Em 01-04-2010 01:33, Dmitri Belimov escreveu:
Quoted 67 lines
Hi Hermann
Quoted 55 lines
Hi Dimitry,
Am Mittwoch, den 31.03.2010, 13:14 +1000 schrieb Dmitri Belimov:
Quoted 44 lines
Hi Hermann
Quoted 27 lines
Hi,
Am Dienstag, den 30.03.2010, 16:02 +1000 schrieb Dmitri Belimov:
Quoted 8 lines
Hi
The hybrid tuner
FMD1216MEX_MK3after cold start has disabled IF. This tuner has internal I2C switch. This switch switch I2C bus between DVB-T and IF part. Default state is DVB-T. When module saa7134 is load it can't find IF tda9887 and disable analog TV mode.Quoted 7 lines
This patch set internal I2C switch of the tuner to IF by send special value to the tuner as for receive analog TV from low band. It can be usefule for other cards.
I didn't set configure a tuner by a tuner model because this tuner can has different I2C address. May be we can do it later after discuss for more robust support a tuners.
just as a reminder. It is the same for the FMD1216ME hybrid MK3. After every boot, analog mode fails with missing tda9887.
Currently, after tuner modules are not independent anymore, one has to reload the saa7134 driver once.
Relevant code in
tuner.core.c.Quoted 14 lines
case TUNER_PHILIPS_FMD1216ME_MK3: buffer[0] = 0x0b; buffer[1] = 0xdc; buffer[2] = 0x9c; buffer[3] = 0x60; i2c_master_send(c, buffer, 4); mdelay(1); buffer[2] = 0x86; buffer[3] = 0x54; i2c_master_send(c, buffer, 4); if (!dvb_attach(simple_tuner_attach, &t->fe, t->i2c->adapter, t->i2c->addr, t->type)) goto attach_failed; break;Quoted 2 lines
That is good. I'll try add case
TUNER_PHILIPS_FMD1216MEX_MK3here and test. This is much better.it wont work for any what I can tell.
We were forced into such an universal looking solution, but it was broken only a short time later.
Quoted 6 lines
I for sure don't say that this time, late 2005, it was in anyway perfect, too much random on module load orders and also duplicate address stuff around meanwhile.
But, however, it seems to be blocked for a global attempt within the current schemes too.
Yes. Not worked. My patch is good for our customers right now. But when this subsystem is ready we can switch to use it.
Quoted 7 lines
Quoted 2 lines
With my best regards, Dmitry.
I'll apply the patch for now, but the better is to fix the
TUNER_PHILIPS_FMD1216MEX_MK3.Dmitri, could you please try to fix it with a more generic solution?
Ok. I'll do it later.
With my best regards, Dmitry.
Quoted 3 lines
Thanks,
Mauro