Skip to contentSkip to conversation

mx31 snd and mc13783 codec status

DISCUSSION Valentin Longchamp 3 participants 10 messages Mar 30, 2010 – Apr 7, 2010

lore
Share & tools
lore
#0 lore raw

Hi Sascha,

For one of our experiments where our robots need to produce sound, I would need a sound driver for mx31moboard platform.

I have quickly hacked something based on what you had done for pcm037 with the MC13783 codec in some of your first sound patches. I know that this is not ready for mainline and I'm still struggling to debug my code, but I would like to have results quite soon so that my colleague could see what sounds (especially regarding to the volume) our system is capable to produce.

I would like to know if by any chance you have some updates on this code ? And do you know if your initial mc13783 codec support coupled with mx31 had some limitations ? Our setup is quite straightforward, we have direct connection from the mx31 to the mc13783 on a single SSI.

Thanks for your precisions.

Val

Signature · 4 lines
Valentin Longchamp, PhD Student, EPFL-STI-LSRO1
[email protected], Phone: +41216937827
http://people.epfl.ch/valentin.longchamp
MEB3494, Station 9, CH-1015 Lausanne
#1 lore raw
Quoted 6 lines · Valentin Longchamp

I have quickly hacked something based on what you had done for pcm037 with the MC13783 codec in some of your first sound patches. I know that this is not ready for mainline and I'm still struggling to debug my code, but I would like to have results quite soon so that my colleague could see what sounds (especially regarding to the volume) our system is capable to produce.

If you're struggling to find time to do full support for the CODEC a good technique is often to get just very basic fixed function support (say just DAC to headphone support) implemented and merged, then go back and implement

I'd also suggest looking at the current Freescale BSPs - obviously this device is used on a lot of Freescale reference boards and I believe there's a reasonably mainlineish driver in the BSPs they have for current devices.

#2 lore raw
Quoted 14 lines · Mark Brown
Quoted 6 lines · Valentin Longchamp

I have quickly hacked something based on what you had done for pcm037 with the MC13783 codec in some of your first sound patches. I know that this is not ready for mainline and I'm still struggling to debug my code, but I would like to have results quite soon so that my colleague could see what sounds (especially regarding to the volume) our system is capable to produce.

If you're struggling to find time to do full support for the CODEC a good technique is often to get just very basic fixed function support (say just DAC to headphone support) implemented and merged, then go back and implement

Quoted 4 lines

I'd also suggest looking at the current Freescale BSPs - obviously this device is used on a lot of Freescale reference boards and I believe there's a reasonably mainlineish driver in the BSPs they have for current devices.

I think they dropped support for the MC13783 in their BSPs. The MC13783 code is still contained in sound/arm/mxc-alsa-pmic.c and a 200k file drivers/mxc/pmic/mc13783/pmic_audio.c. That's not exactly mainlineish...

Sascha

Signature · 4 lines
Pengutronix e.K.                           |                             |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |
#3 lore raw
In reply to Valentin Longchamp

Hi Valentin,

Quoted 12 lines · Valentin Longchamp

Hi Sascha,

For one of our experiments where our robots need to produce sound, I would need a sound driver for mx31moboard platform.

I have quickly hacked something based on what you had done for pcm037 with the MC13783 codec in some of your first sound patches. I know that this is not ready for mainline and I'm still struggling to debug my code, but I would like to have results quite soon so that my colleague could see what sounds (especially regarding to the volume) our system is capable to produce.

Quoted 2 lines

I would like to know if by any chance you have some updates on this code ?

Find the latest version of my code here:

The following changes since commit 01e77706cdde7c0b47e5ca1f4284a795504c7c40:
Linus Torvalds (1):
Merge branch 'for-linus' of git://gitorious.org/linux-omap-dss2/linux

are available in the git repository at:

git://git.pengutronix.de/git/sha/linux-2.6.git mc13783

Sascha Hauer (3):
add a mc13783 codec driver
add phycore-mc13783 sound support
pcm038: add sound support

 arch/arm/mach-mx2/mach-pcm038.c |   23 ++-
 sound/soc/codecs/Kconfig        |    4 +
 sound/soc/codecs/Makefile       |    2 +
 sound/soc/codecs/mc13783.c      |  727 +++++++++++++++++++++++++++++++++++++++
 sound/soc/codecs/mc13783.h      |   32 ++
 sound/soc/imx/Kconfig           |    9 +
 sound/soc/imx/Makefile          |    3 +
 sound/soc/imx/phycore-mc13783.c |  160 +++++++++
 8 files changed, 959 insertions(+), 1 deletions(-)
 create mode 100644 sound/soc/codecs/mc13783.c
 create mode 100644 sound/soc/codecs/mc13783.h
 create mode 100644 sound/soc/imx/phycore-mc13783.c
Quoted 3 lines

And do you know if your initial mc13783 codec support coupled with mx31 had some limitations ? Our setup is quite straightforward, we have direct connection from the mx31 to the mc13783 on a single SSI.

Our board uses both SSI channels of the MC13783 which we then mux into one channel in the DAM unit. I don't know how this affects you.

Sascha

Signature · 4 lines
Pengutronix e.K.                           |                             |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |
#4 lore raw

Hi Sascha,

Quoted 29 lines · Sascha Hauer

Find the latest version of my code here:

The following changes since commit 01e77706cdde7c0b47e5ca1f4284a795504c7c40:
Linus Torvalds (1):
Merge branch 'for-linus' of git://gitorious.org/linux-omap-dss2/linux

are available in the git repository at:

git://git.pengutronix.de/git/sha/linux-2.6.git mc13783

Sascha Hauer (3):
add a mc13783 codec driver
add phycore-mc13783 sound support
pcm038: add sound support

 arch/arm/mach-mx2/mach-pcm038.c |   23 ++-
 sound/soc/codecs/Kconfig        |    4 +
 sound/soc/codecs/Makefile       |    2 +
 sound/soc/codecs/mc13783.c      |  727 +++++++++++++++++++++++++++++++++++++++
 sound/soc/codecs/mc13783.h      |   32 ++
 sound/soc/imx/Kconfig           |    9 +
 sound/soc/imx/Makefile          |    3 +
 sound/soc/imx/phycore-mc13783.c |  160 +++++++++
 8 files changed, 959 insertions(+), 1 deletions(-)
 create mode 100644 sound/soc/codecs/mc13783.c
 create mode 100644 sound/soc/codecs/mc13783.h
 create mode 100644 sound/soc/imx/phycore-mc13783.c
Quoted 5 lines
Quoted 1 line

And do you know if your initial mc13783 codec support coupled with mx31 had some limitations ? Our setup is quite straightforward, we have direct connection from the mx31 to the mc13783 on a single SSI.

Our board uses both SSI channels of the MC13783 which we then mux into one channel in the DAM unit. I don't know how this affects you.

I have struggled with the DAM unit (this thing is an awful bulk of wires) and now I get some sound on the loudspeaker.

The thing is that I get a less than a second sound loop (I use aplay to test, so userspace app should be ok), as if the buffer that the fiq asm interrupt (from ssi_fiq.S) copies to the SSI hardware never was updated.

If I have understood the fiq behaviour correctly, you have a asm fiq interrupt that does copy a larger tx buffer into the SSI hardware. Besides it, you have the imx_ssi_timer_callback that checks when the tx buffer was completely copied. If it is the case, then a new buffer tx buffer is "issued" with the snd_pcm_period_elapsed call (and then snd_pcm_update_hw_ptr0). Is this behaviour correct ?

If then it looks like on my system, I have a problem with the snd_pcm_update_hw_ptr0 call.

Thanks

Val

Signature · 4 lines
Valentin Longchamp, PhD Student, EPFL-STI-LSRO1
[email protected], Phone: +41216937827
http://people.epfl.ch/valentin.longchamp
MEB3494, Station 9, CH-1015 Lausanne
#5 lore raw
Quoted 47 lines · Valentin Longchamp

Hi Sascha,

Quoted 29 lines · Sascha Hauer

Find the latest version of my code here:

The following changes since commit 01e77706cdde7c0b47e5ca1f4284a795504c7c40:
Linus Torvalds (1):
Merge branch 'for-linus' of git://gitorious.org/linux-omap-dss2/linux

are available in the git repository at:

git://git.pengutronix.de/git/sha/linux-2.6.git mc13783

Sascha Hauer (3):
add a mc13783 codec driver
add phycore-mc13783 sound support
pcm038: add sound support

 arch/arm/mach-mx2/mach-pcm038.c |   23 ++-
 sound/soc/codecs/Kconfig        |    4 +
 sound/soc/codecs/Makefile       |    2 +
 sound/soc/codecs/mc13783.c      |  727 +++++++++++++++++++++++++++++++++++++++
 sound/soc/codecs/mc13783.h      |   32 ++
 sound/soc/imx/Kconfig           |    9 +
 sound/soc/imx/Makefile          |    3 +
 sound/soc/imx/phycore-mc13783.c |  160 +++++++++
 8 files changed, 959 insertions(+), 1 deletions(-)
 create mode 100644 sound/soc/codecs/mc13783.c
 create mode 100644 sound/soc/codecs/mc13783.h
 create mode 100644 sound/soc/imx/phycore-mc13783.c
Quoted 7 lines
Quoted 3 lines

And do you know if your initial mc13783 codec support coupled with mx31 had some limitations ? Our setup is quite straightforward, we have direct connection from the mx31 to the mc13783 on a single SSI.

Our board uses both SSI channels of the MC13783 which we then mux into one channel in the DAM unit. I don't know how this affects you.

I have struggled with the DAM unit (this thing is an awful bulk of wires) and now I get some sound on the loudspeaker.

The thing is that I get a less than a second sound loop (I use aplay to test, so userspace app should be ok), as if the buffer that the fiq asm interrupt (from ssi_fiq.S) copies to the SSI hardware never was updated.

Quoted 6 lines

If I have understood the fiq behaviour correctly, you have a asm fiq interrupt that does copy a larger tx buffer into the SSI hardware. Besides it, you have the imx_ssi_timer_callback that checks when the tx buffer was completely copied. If it is the case, then a new buffer tx buffer is "issued" with the snd_pcm_period_elapsed call (and then snd_pcm_update_hw_ptr0). Is this behaviour correct ?

Yes.

Quoted 3 lines

If then it looks like on my system, I have a problem with the snd_pcm_update_hw_ptr0 call.

You could try reverting b4e82b5b785670b68136765059d1afc65c0ae023. Though I have tested it on my boards it may have some implications.

Sascha

Signature · 4 lines
Pengutronix e.K.                           |                             |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |
#6 lore raw
Quoted 6 lines · Sascha Hauer
Quoted 3 lines · Valentin Longchamp

The thing is that I get a less than a second sound loop (I use aplay to test, so userspace app should be ok), as if the buffer that the fiq asm interrupt (from ssi_fiq.S) copies to the SSI hardware never was updated.

Quoted 8 lines
Quoted 6 lines

If I have understood the fiq behaviour correctly, you have a asm fiq interrupt that does copy a larger tx buffer into the SSI hardware. Besides it, you have the imx_ssi_timer_callback that checks when the tx buffer was completely copied. If it is the case, then a new buffer tx buffer is "issued" with the snd_pcm_period_elapsed call (and then snd_pcm_update_hw_ptr0). Is this behaviour correct ?

Yes.

What sample rate are you trying to play and what buffer size? In my testing the FIQ was really struggling with most applications at sample rates over ~16kHz since you need each audio period to be long enough to at least fill the interval between timer polls but applications wanted to select buffer sizes that were consumed faster than the timer tick.

Using an application like speaker-test which has minimal overhead and no I/O to worry about helps too.

Quoted 5 lines
Quoted 2 lines

If then it looks like on my system, I have a problem with the snd_pcm_update_hw_ptr0 call.

You could try reverting b4e82b5b785670b68136765059d1afc65c0ae023. Though I have tested it on my boards it may have some implications.

I was seeing similar behaviour before and after that patch too, the main effect there was to improve the error handling when the FIQ and the timer get out of sync with each other.

#7 lore raw
Quoted 11 lines · Mark Brown
Quoted 1 line · Sascha Hauer

On Thu, Apr 01, 2010 at 06:01:38PM +0200, Valentin Longchamp wrote:

What sample rate are you trying to play and what buffer size? In my testing the FIQ was really struggling with most applications at sample rates over ~16kHz since you need each audio period to be long enough to at least fill the interval between timer polls but applications wanted to select buffer sizes that were consumed faster than the timer tick.

Using an application like speaker-test which has minimal overhead and no I/O to worry about helps too.

OK, I have done some tests with speaker-test and I experienced the same as you did: with rates over 16kHz, the FIQ starts to have some problems.

Quoted 9 lines
Quoted 5 lines
Quoted 2 lines

If then it looks like on my system, I have a problem with the snd_pcm_update_hw_ptr0 call.

You could try reverting b4e82b5b785670b68136765059d1afc65c0ae023. Though I have tested it on my boards it may have some implications.

I was seeing similar behaviour before and after that patch too, the main effect there was to improve the error handling when the FIQ and the timer get out of sync with each other.

Mark is right, the behavior is similar with or without this patch, it does not improve the FIQ problems with rates over 16 kHz.

Val

Signature · 4 lines
Valentin Longchamp, PhD Student, EPFL-STI-LSRO1
[email protected], Phone: +41216937827
http://people.epfl.ch/valentin.longchamp
MEB3494, Station 9, CH-1015 Lausanne
#8 lore raw
In reply to Mark Brown
Quoted 14 lines · Mark Brown
Quoted 12 lines · Sascha Hauer
Quoted 10 lines · Valentin Longchamp

The thing is that I get a less than a second sound loop (I use aplay to test, so userspace app should be ok), as if the buffer that the fiq asm interrupt (from ssi_fiq.S) copies to the SSI hardware never was updated.

If I have understood the fiq behaviour correctly, you have a asm fiq interrupt that does copy a larger tx buffer into the SSI hardware. Besides it, you have the imx_ssi_timer_callback that checks when the tx buffer was completely copied. If it is the case, then a new buffer tx buffer is "issued" with the snd_pcm_period_elapsed call (and then snd_pcm_update_hw_ptr0). Is this behaviour correct ?

Quoted 7 lines
Quoted 1 line

Yes.

What sample rate are you trying to play and what buffer size? In my testing the FIQ was really struggling with most applications at sample rates over ~16kHz since you need each audio period to be long enough to at least fill the interval between timer polls but applications wanted to select buffer sizes that were consumed faster than the timer tick.

I just stumbled upon a board which had something in /etc/asound.conf which decreased the buffer sizes. The result was choppy sound and a cpu utilisation of ~40%.

After deleting the file I could play sounds (and record simultaniously) with rates up to 44100kHz without visible cpu utilisation.

Looking at it I realised that poll_time is 0, so the timer gets reloaded with the actual jiffies value which of course is a bad idea. We should probably use a hrtimer here.

Sascha

Signature · 4 lines
Pengutronix e.K.                           |                             |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |
#9 lore raw
Quoted 10 lines · Sascha Hauer
Quoted 5 lines · Mark Brown

What sample rate are you trying to play and what buffer size? In my testing the FIQ was really struggling with most applications at sample rates over ~16kHz since you need each audio period to be long enough to at least fill the interval between timer polls but applications wanted to select buffer sizes that were consumed faster than the timer tick.

After deleting the file I could play sounds (and record simultaniously) with rates up to 44100kHz without visible cpu utilisation.

Yes, if you tweak the buffer sizes (most of the ALSA test utilities support this) then you can use higher sample rates - pulseaudio's high latency modes should work great, for example.

Quoted 3 lines

Looking at it I realised that poll_time is 0, so the timer gets reloaded with the actual jiffies value which of course is a bad idea. We should probably use a hrtimer here.

Yes, by default you're only going to be able to poll at 1ms intervals so the poll time ends up going down to zero. I did look at switching over to a hrtimer when I was fixing up the sample rate slips but I wasn't able to convince myself that there was a hrtimer offering sufficient resolution available on i.MX.