Skip to contentSkip to conversation

can: Add driver for SJA1000 based PCI CAN interface cards by esd

PATCH In review Matthias Fuchs 3 participants 4 messages Mar 31, 2010 3 messages not in the archive

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 can: Add driver for SJA1000 based PCI CAN interface cards by esd

This patch adds support for SJA1000 based PCI CAN interface cards from electronic system design gmbh.

These boards are supported:

        CAN-PCI/200 (PCI)
        CAN-PCI/266 (PCI)
        CAN-PMC266 (PMC module)
        CAN-PCIe/2000 (PCI Express)
        CAN-CPCI/200 (Compact PCI, 3U)
        CAN-PCI104 (PCI104)

This driver is part of the SocketCAN SVN repository since April 2009.

---
 drivers/net/can/sja1000/Kconfig   |    9 +
 drivers/net/can/sja1000/Makefile  |    1 +
 drivers/net/can/sja1000/esd_pci.c |  315 +++++++++++++++++++++++++++++++++++++
 3 files changed, 325 insertions(+), 0 deletions(-)
 create mode 100644 drivers/net/can/sja1000/esd_pci.c
drivers/net/can/sja1000/Kconfig +9 -0
index 9e277d6..c01eb4e 100644
@@ -37,6 +37,15 @@ config CAN_EMS_PCI
 	  CPC-PCIe and CPC-104P cards from EMS Dr. Thomas Wuensche
 	  (http://www.ems-wuensche.de).
 
+config CAN_ESD_PCI
+	tristate "ESD PCI Cards"
+	depends on PCI
+	---help---
+	  This driver supports the esd PCI CAN cards CAN-PCI/200,
+	  CAN-PCI/266, CAN-PMC/266 (PMC), CAN-CPCI/200 (CompactPCI),
+	  CAN-PCIe2000 (PCI Express) and CAN-PCI104/200 (PCI104)
+	  from the esd electronic system design gmbh (http://www.esd.eu).
+
 config CAN_KVASER_PCI
 	tristate "Kvaser PCIcanx and Kvaser PCIcan PCI Cards"
 	depends on PCI
drivers/net/can/sja1000/Makefile +1 -0
index ce92455..a8dcbe0 100644
@@ -7,6 +7,7 @@ obj-$(CONFIG_CAN_SJA1000_ISA) += sja1000_isa.o
 obj-$(CONFIG_CAN_SJA1000_PLATFORM) += sja1000_platform.o
 obj-$(CONFIG_CAN_SJA1000_OF_PLATFORM) += sja1000_of_platform.o
 obj-$(CONFIG_CAN_EMS_PCI) += ems_pci.o
+obj-$(CONFIG_CAN_ESD_PCI) += esd_pci.o
 obj-$(CONFIG_CAN_KVASER_PCI) += kvaser_pci.o
 obj-$(CONFIG_CAN_PLX_PCI) += plx_pci.o
 
drivers/net/can/sja1000/esd_pci.c new file +315 -0

315 lines not on this page · raw message

Signature · 1 line
1.6.1

A message that is not in the archive (sent off-list or not yet received): [email protected]

#2 lore raw

Hi Matthias,

Quoted 12 lines · Matthias Fuchs

This patch adds support for SJA1000 based PCI CAN interface cards from electronic system design gmbh.

These boards are supported:

        CAN-PCI/200 (PCI)
        CAN-PCI/266 (PCI)
        CAN-PMC266 (PMC module)
        CAN-PCIe/2000 (PCI Express)
        CAN-CPCI/200 (Compact PCI, 3U)
        CAN-PCI104 (PCI104)
Quoted 4 lines

This driver is part of the SocketCAN SVN repository since April 2009.

Since a while we have a generic PCI PLX driver in the mainline kernel, which could support the esd cards as well, I believe.

Wolfgang.

A message that is not in the archive (sent off-list or not yet received): [email protected]

#4 lore raw

Hi Wolfgang,

I am aware of the PCI PLX driver. It should be possible to adapt that one. It lacks PLX9056 support so it's not done by just adding some PCI device IDs.

But if that's how it should be done I will do so.

Matthias

Quoted 26 lines · Wolfgang Grandegger

Hi Matthias,

Quoted 12 lines · Matthias Fuchs

This patch adds support for SJA1000 based PCI CAN interface cards from electronic system design gmbh.

These boards are supported:

        CAN-PCI/200 (PCI)
        CAN-PCI/266 (PCI)
        CAN-PMC266 (PMC module)
        CAN-PCIe/2000 (PCI Express)
        CAN-CPCI/200 (Compact PCI, 3U)
        CAN-PCI104 (PCI104)
Quoted 4 lines

This driver is part of the SocketCAN SVN repository since April 2009.

Since a while we have a generic PCI PLX driver in the mainline kernel, which could support the esd cards as well, I believe.

Wolfgang.

A message that is not in the archive (sent off-list or not yet received): [email protected]

#6 lore raw
Quoted 9 lines · Matthias Fuchs

Hi Wolfgang,

I am aware of the PCI PLX driver. It should be possible to adapt that one. It lacks PLX9056 support so it's not done by just adding some PCI device IDs.

But if that's how it should be done I will do so.

From the maintenance point of view, that's the preferred solution.

Thanks for your effort.

Wolfgang.