Skip to contentSkip to conversation

ahci 0000:00:1f.2: controller reset failed (0xffffffff)

2.6.34-rc1 REGRESSION Andy Isaacson 7 participants 16 messages Apr 6, 2010 – Apr 13, 2010 x86

lore
Share & tools
lore
#0 lore raw

This Dell Precision WorkStation T3400 doesn't boot 2.6.34-rc1 (tried 522dba71). 2.6.33 was fine, and it's been running various stable kernels for the last 18 months. Unfortunately I can't reasonably bisect as I need this machine to be usable, but I can test specific patches or options. (three or four reboots is fine, 15 is not.)

full dmesg from failing boot and a successful boot at
http://web.hexapodia.org/~adi/tmp/20100406-pci-ahci-reset-fail/

I suspect it's due to:

[    3.094038] pci 0000:00:1f.2: no compatible bridge window for [mem 0xff970000-0xff9707ff]
[    3.103001] pci 0000:00:1f.2: can't reserve [mem 0xff970000-0xff9707ff]

so I've CCed a few recent committers to setup-res.c.

dmesg up to point of failure:

[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 2.6.34-rc1-00005-g522dba7 (andy@farthing) (gcc version 4.3.3 (Debian 4.3.3-5) ) #4 SMP Tue Apr 6 12:20:02 PDT 2010
[    0.000000] Command line: BOOT_IMAGE=/vmlinuz-2.6.34-rc1-00005-g522dba7 root=UUID=a2359eda-9295-451c-924f-c181c6f49d0d ro console=tty1 console=ttyS0,115200
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  BIOS-e820: 0000000000000000 - 000000000009ec00 (usable)
[    0.000000]  BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 00000000bfe01c00 (usable)
[    0.000000]  BIOS-e820: 00000000bfe01c00 - 00000000bfe53c00 (ACPI NVS)
[    0.000000]  BIOS-e820: 00000000bfe53c00 - 00000000bfe55c00 (ACPI data)
[    0.000000]  BIOS-e820: 00000000bfe55c00 - 00000000c0000000 (reserved)
[    0.000000]  BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
[    0.000000]  BIOS-e820: 00000000fec00000 - 00000000fed00400 (reserved)
[    0.000000]  BIOS-e820: 00000000fed20000 - 00000000feda0000 (reserved)
[    0.000000]  BIOS-e820: 00000000fee00000 - 00000000fef00000 (reserved)
[    0.000000]  BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
[    0.000000]  BIOS-e820: 0000000100000000 - 00000001bc000000 (usable)
[    0.000000] NX (Execute Disable) protection: active
[    0.000000] DMI 2.5 present.
[    0.000000] No AGP bridge found
[    0.000000] last_pfn = 0x1bc000 max_arch_pfn = 0x400000000
[    0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[    0.000000] last_pfn = 0xbfe01 max_arch_pfn = 0x400000000
[    0.000000] found SMP MP-table at [ffff8800000fe710] fe710
[    0.000000] init_memory_mapping: 0000000000000000-00000000bfe01000
[    0.000000] init_memory_mapping: 0000000100000000-00000001bc000000
[    0.000000] RAMDISK: 37c8e000 - 37fef049
[    0.000000] ACPI: RSDP 00000000000febf0 00024 (v02 DELL  )
[    0.000000] ACPI: XSDT 00000000000fcea4 0006C (v01 DELL    B9K     00000015 ASL  00000061)
[    0.000000] ACPI: FACP 00000000000fcfcc 000F4 (v03 DELL    B9K     00000015 ASL  00000061)
[    0.000000] ACPI: DSDT 00000000fff5aafd 03794 (v01   DELL    dt_ex 00001000 INTL 20050624)
[    0.000000] ACPI: FACS 00000000bfe01c00 00040
[    0.000000] ACPI: SSDT 00000000fff5e291 00099 (v01   DELL    st_ex 00001000 INTL 20050624)
[    0.000000] ACPI: APIC 00000000000fd0c0 00092 (v01 DELL    B9K     00000015 ASL  00000061)
[    0.000000] ACPI: BOOT 00000000000fd152 00028 (v01 DELL    B9K     00000015 ASL  00000061)
[    0.000000] ACPI: ASF! 00000000000fd17a 00096 (v32 DELL    B9K     00000015 ASL  00000061)
[    0.000000] ACPI: MCFG 00000000000fd210 0003E (v01 DELL    B9K     00000015 ASL  00000061)
[    0.000000] ACPI: HPET 00000000000fd24e 00038 (v01 DELL    B9K     00000015 ASL  00000061)
[    0.000000] ACPI: TCPA 00000000000fd4aa 00032 (v01 DELL    B9K     00000015 ASL  00000061)
[    0.000000] ACPI: SLIC 00000000000fd286 00176 (v01 DELL    B9K     00000015 ASL  00000061)
[    0.000000] No NUMA configuration found
[    0.000000] Faking a node at 0000000000000000-00000001bc000000
[    0.000000] Initmem setup node 0 0000000000000000-00000001bc000000
[    0.000000]   NODE_DATA [0000000100000000 - 0000000100004fff]
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA      0x00000001 -> 0x00001000
[    0.000000]   DMA32    0x00001000 -> 0x00100000
[    0.000000]   Normal   0x00100000 -> 0x001bc000
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[3] active PFN ranges
[    0.000000]     0: 0x00000001 -> 0x0000009e
[    0.000000]     0: 0x00000100 -> 0x000bfe01
[    0.000000]     0: 0x00100000 -> 0x001bc000
[    0.000000] ACPI: PM-Timer IO Port: 0x808
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x00] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x01] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x02] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x08] lapic_id[0x03] disabled)
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0xff] high level lint[0x1])
[    0.000000] ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] ACPI: HPET id: 0x8086a301 base: 0xfed00000
[    0.000000] SMP: Allowing 8 CPUs, 4 hotplug CPUs
[    0.000000] PM: Registered nosave memory: 000000000009e000 - 00000000000f0000
[    0.000000] PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
[    0.000000] PM: Registered nosave memory: 00000000bfe01000 - 00000000bfe02000
[    0.000000] PM: Registered nosave memory: 00000000bfe02000 - 00000000bfe53000
[    0.000000] PM: Registered nosave memory: 00000000bfe53000 - 00000000bfe54000
[    0.000000] PM: Registered nosave memory: 00000000bfe54000 - 00000000bfe55000
[    0.000000] PM: Registered nosave memory: 00000000bfe55000 - 00000000bfe56000
[    0.000000] PM: Registered nosave memory: 00000000bfe56000 - 00000000c0000000
[    0.000000] PM: Registered nosave memory: 00000000c0000000 - 00000000e0000000
[    0.000000] PM: Registered nosave memory: 00000000e0000000 - 00000000f0000000
[    0.000000] PM: Registered nosave memory: 00000000f0000000 - 00000000fec00000
[    0.000000] PM: Registered nosave memory: 00000000fec00000 - 00000000fed00000
[    0.000000] PM: Registered nosave memory: 00000000fed00000 - 00000000fed20000
[    0.000000] PM: Registered nosave memory: 00000000fed20000 - 00000000feda0000
[    0.000000] PM: Registered nosave memory: 00000000feda0000 - 00000000fee00000
[    0.000000] PM: Registered nosave memory: 00000000fee00000 - 00000000fef00000
[    0.000000] PM: Registered nosave memory: 00000000fef00000 - 00000000ffb00000
[    0.000000] PM: Registered nosave memory: 00000000ffb00000 - 0000000100000000
[    0.000000] Allocating PCI resources starting at c0000000 (gap: c0000000:20000000)
[    0.000000] setup_percpu: NR_CPUS:64 nr_cpumask_bits:64 nr_cpu_ids:8 nr_node_ids:1
[    0.000000] PERCPU: Embedded 27 pages/cpu @ffff880001e00000 s81704 r8192 d20696 u262144
[    0.000000] pcpu-alloc: s81704 r8192 d20696 u262144 alloc=1*2097152
[    0.000000] pcpu-alloc: [0] 0 1 2 3 4 5 6 7 
[    0.000000] Built 1 zonelists in Node order, mobility grouping on.  Total pages: 1531006
[    0.000000] Policy zone: Normal
[    0.000000] Kernel command line: BOOT_IMAGE=/vmlinuz-2.6.34-rc1-00005-g522dba7 root=UUID=a2359eda-9295-451c-924f-c181c6f49d0d ro console=tty1 console=ttyS0,115200
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] Checking aperture...
[    0.000000] No AGP bridge found
[    0.000000] Subtract (62 early reservations)
[    0.000000]   #1 [0001000000 - 0001dafd28]   TEXT DATA BSS
[    0.000000]   #2 [0037c8e000 - 0037fef049]         RAMDISK
[    0.000000]   #3 [0001db0000 - 0001db01a8]             BRK
[    0.000000]   #4 [00000fe720 - 0000100000]   BIOS reserved
[    0.000000]   #5 [00000fe710 - 00000fe720]    MP-table mpf
[    0.000000]   #6 [000009ec00 - 00000f0000]   BIOS reserved
[    0.000000]   #7 [00000f0304 - 00000fe710]   BIOS reserved
[    0.000000]   #8 [00000f0000 - 00000f0304]    MP-table mpc
[    0.000000]   #9 [0000001000 - 0000003000]      TRAMPOLINE
[    0.000000]   #10 [0000003000 - 0000007000]     ACPI WAKEUP
[    0.000000]   #11 [0000008000 - 000000b000]         PGTABLE
[    0.000000]   #12 [000000b000 - 000000e000]         PGTABLE
[    0.000000]   #13 [0100000000 - 0100005000]       NODE_DATA
[    0.000000]   #14 [0001db01c0 - 0001db11c0]         BOOTMEM
[    0.000000]   #15 [00021b11c0 - 00021b1640]         BOOTMEM
[    0.000000]   #16 [0100005000 - 0100006000]         BOOTMEM
[    0.000000]   #17 [0100006000 - 0100007000]         BOOTMEM
[    0.000000]   #18 [0100200000 - 0105600000]        MEMMAP 0
[    0.000000]   #19 [0001dafd40 - 0001dafec0]         BOOTMEM
[    0.000000]   #20 [0001db11c0 - 0001dc91c0]         BOOTMEM
[    0.000000]   #21 [0001dc91c0 - 0001de11c0]         BOOTMEM
[    0.000000]   #22 [0001de2000 - 0001de3000]         BOOTMEM
[    0.000000]   #23 [0001dafec0 - 0001daff01]         BOOTMEM
[    0.000000]   #24 [0001daff40 - 0001daff83]         BOOTMEM
[    0.000000]   #25 [0001de11c0 - 0001de1498]         BOOTMEM
[    0.000000]   #26 [0001de14c0 - 0001de1528]         BOOTMEM
[    0.000000]   #27 [0001de1540 - 0001de15a8]         BOOTMEM
[    0.000000]   #28 [0001de15c0 - 0001de1628]         BOOTMEM
[    0.000000]   #29 [0001de1640 - 0001de16a8]         BOOTMEM
[    0.000000]   #30 [0001de16c0 - 0001de1728]         BOOTMEM
[    0.000000]   #31 [0001de1740 - 0001de17a8]         BOOTMEM
[    0.000000]   #32 [0001de17c0 - 0001de1828]         BOOTMEM
[    0.000000]   #33 [0001de1840 - 0001de18a8]         BOOTMEM
[    0.000000]   #34 [0001de18c0 - 0001de1928]         BOOTMEM
[    0.000000]   #35 [0001de1940 - 0001de19a8]         BOOTMEM
[    0.000000]   #36 [0001de19c0 - 0001de1a28]         BOOTMEM
[    0.000000]   #37 [0001de1a40 - 0001de1aa8]         BOOTMEM
[    0.000000]   #38 [0001daffc0 - 0001daffe0]         BOOTMEM
[    0.000000]   #39 [0001de1ac0 - 0001de1ae0]         BOOTMEM
[    0.000000]   #40 [0001de1b00 - 0001de1b82]         BOOTMEM
[    0.000000]   #41 [0001de1bc0 - 0001de1c42]         BOOTMEM
[    0.000000]   #42 [0001e00000 - 0001e1b000]         BOOTMEM
[    0.000000]   #43 [0001e40000 - 0001e5b000]         BOOTMEM
[    0.000000]   #44 [0001e80000 - 0001e9b000]         BOOTMEM
[    0.000000]   #45 [0001ec0000 - 0001edb000]         BOOTMEM
[    0.000000]   #46 [0001f00000 - 0001f1b000]         BOOTMEM
[    0.000000]   #47 [0001f40000 - 0001f5b000]         BOOTMEM
[    0.000000]   #48 [0001f80000 - 0001f9b000]         BOOTMEM
[    0.000000]   #49 [0001fc0000 - 0001fdb000]         BOOTMEM
[    0.000000]   #50 [0001de1c80 - 0001de1c88]         BOOTMEM
[    0.000000]   #51 [0001de1cc0 - 0001de1cc8]         BOOTMEM
[    0.000000]   #52 [0001de1d00 - 0001de1d20]         BOOTMEM
[    0.000000]   #53 [0001de1d40 - 0001de1d80]         BOOTMEM
[    0.000000]   #54 [0001de1d80 - 0001de1ea0]         BOOTMEM
[    0.000000]   #55 [0001de1ec0 - 0001de1f08]         BOOTMEM
[    0.000000]   #56 [0001de1f40 - 0001de1f88]         BOOTMEM
[    0.000000]   #57 [0001de3000 - 0001deb000]         BOOTMEM
[    0.000000]   #58 [00021b2000 - 00061b2000]         BOOTMEM
[    0.000000]   #59 [0001e1b000 - 0001e3b000]         BOOTMEM
[    0.000000]   #60 [0001fdb000 - 000201b000]         BOOTMEM
[    0.000000]   #61 [000000f000 - 0000017000]         BOOTMEM
[    0.000000] Memory: 6052852k/7274496k available (5329k kernel code, 1051016k absent, 170628k reserved, 6546k data, 612k init)
[    0.000000] SLUB: Genslabs=14, HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:2304
[    0.000000] Console: colour VGA+ 80x25
[    0.000000] console [tty1] enabled
[    0.000000] console [ttyS0] enabled
[    0.000000] Fast TSC calibration using PIT
[    0.000000] Detected 2393.797 MHz processor.
[    0.002005] Calibrating delay loop (skipped), value calculated using timer frequency.. 4787.59 BogoMIPS (lpj=2393797)
[    0.004021] Security Framework initialized
[    0.005005] SELinux:  Initializing.
[    0.007338] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes)
[    0.013628] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes)
[    0.017413] Mount-cache hash table entries: 256
[    0.018185] Initializing cgroup subsys ns
[    0.019007] Initializing cgroup subsys cpuacct
[    0.020006] Initializing cgroup subsys blkio
[    0.021031] CPU: Physical Processor ID: 0
[    0.022002] CPU: Processor Core ID: 0
[    0.023003] using mwait in idle threads.
[    0.024002] Performance Events: Core2 events, Intel PMU driver.
[    0.027003] ... version:                2
[    0.028002] ... bit width:              40
[    0.029002] ... generic registers:      2
[    0.030002] ... value mask:             000000ffffffffff
[    0.031002] ... max period:             000000007fffffff
[    0.032002] ... fixed-purpose events:   3
[    0.033002] ... event mask:             0000000700000003
[    0.034039] ACPI: Core revision 20100121
[    0.201068] Setting APIC routing to flat
[    0.202470] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.213995] CPU0: Intel(R) Core(TM)2 Quad CPU    Q6600  @ 2.40GHz stepping 0b
[    0.216999] Booting Node   0, Processors  #1 #2 #3
[    0.433006] Brought up 4 CPUs
[    0.434002] Total of 4 processors activated (19150.90 BogoMIPS).
[    0.436105] khelper used greatest stack depth: 5976 bytes left
[    0.443364] Time: 19:28:47  Date: 04/06/10
[    0.444034] NET: Registered protocol family 16
[    0.445040] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
[    0.446008] ACPI: bus type pci registered
[    0.447041] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[    0.448002] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in E820
[    0.470238] PCI: Using configuration type 1 for base access
[    0.483041] bio: create slab <bio-0> at 0
[    0.515520] ACPI: BIOS _OSI(Linux) query ignored
[    0.562237] ACPI: Interpreter enabled
[    0.566003] ACPI: (supports S0 S1 S3 S4 S5)
[    0.570003] ACPI: Using IOAPIC for interrupt routing
[    0.763201] ACPI Warning: Incorrect checksum in table [TCPA] - 00, should be 87 (20100121/tbutils-314)
[    0.773064] ACPI: No dock devices found.
[    0.777002] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    0.796381] ACPI: PCI Root Bridge [PCI0] (0000:00)
[    0.822373] pci_root PNP0A03:00: host bridge window [io  0x0000-0x0cf7]
[    0.829002] pci_root PNP0A03:00: host bridge window [io  0x0d00-0xffff]
[    0.836002] pci_root PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff]
[    0.843002] pci_root PNP0A03:00: host bridge window [mem 0x000c0000-0x000effff]
[    0.851002] pci_root PNP0A03:00: host bridge window [mem 0x000f0000-0x000fffff]
[    0.858002] pci_root PNP0A03:00: host bridge window [mem 0xf0000000-0xfebfffff]
[    0.866001] pci_root PNP0A03:00: host bridge window [mem 0xbff00000-0xdfffffff]
[    0.873002] pci_root PNP0A03:00: host bridge window [mem 0xff980800-0xff980bff]
[    0.880001] pci_root PNP0A03:00: host bridge window [mem 0xff97c000-0xff97ffff]
[    0.888001] pci_root PNP0A03:00: host bridge window [mem 0xfed20000-0xfed9ffff]
[    0.896396] pci 0000:00:1f.0: quirk: [io  0x0800-0x087f] claimed by ICH6 ACPI/GPIO/TCO
[    0.905003] pci 0000:00:1f.0: quirk: [io  0x0880-0x08bf] claimed by ICH6 GPIO
[    0.912003] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0c00 (mask 007f)
[    0.919002] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 2 PIO at 00e0 (mask 0007)
[    0.927258] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[    0.933033] pci 0000:00:06.0: PCI bridge to [bus 02-02]
[    0.938047] pci 0000:00:1c.0: PCI bridge to [bus 03-03]
[    0.943193] pci 0000:00:1c.5: PCI bridge to [bus 04-04]
[    0.949107] pci 0000:00:1e.0: PCI bridge to [bus 05-05] (subtractive decode)
[    2.980627] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 15)
[    2.989442] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11 12 15)
[    2.998052] ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 6 7 9 10 11 12 15)
[    3.005658] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 11 12 15) *0, disabled.
[    3.015669] ACPI: PCI Interrupt Link [LNKE] (IRQs *3 4 5 6 7 9 10 11 12 15)
[    3.024274] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 15) *0, disabled.
[    3.034278] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 *9 10 11 12 15)
[    3.042772] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 6 7 9 10 11 12 15)
[    3.051037] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
[    3.060003] vgaarb: loaded
[    3.063026] SCSI subsystem initialized
[    3.067030] usbcore: registered new interface driver usbfs
[    3.073017] usbcore: registered new interface driver hub
[    3.078021] usbcore: registered new device driver usb
[    3.083029] Advanced Linux Sound Architecture Driver Version 1.0.22.1.
[    3.090002] PCI: Using ACPI for IRQ routing
[    3.094038] pci 0000:00:1f.2: no compatible bridge window for [mem 0xff970000-0xff9707ff]
[    3.103001] pci 0000:00:1f.2: can't reserve [mem 0xff970000-0xff9707ff]
[    3.109043] Expanded resource reserved due to conflict with PCI Bus 0000:00
[    3.117046] cfg80211: Calling CRDA to update world regulatory domain
[    3.123017] NetLabel: Initializing
[    3.127001] NetLabel:  domain hash size = 128
[    3.131001] NetLabel:  protocols = UNLABELED CIPSOv4
[    3.136011] NetLabel:  unlabeled traffic allowed by default
[    3.142004] HPET: 4 timers in total, 0 timers will be used for per-cpu timer
[    3.149004] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0
[    3.154688] hpet0: 4 comparators, 64-bit 14.318180 MHz counter
[    3.163041] Switching to clocksource tsc
[    3.176654] pnp: PnP ACPI init
[    3.179907] ACPI: bus type pnp registered
[    3.200843] pnp 00:01: disabling [io  0x0800-0x085f] because it overlaps 0000:00:1f.0 BAR 7 [io  0x0800-0x087f]
[    3.211250] pnp 00:01: disabling [io  0x0860-0x08ff] because it overlaps 0000:00:1f.0 BAR 7 [io  0x0800-0x087f]
[    3.285911] pnp: PnP ACPI: found 12 devices
[    3.290274] ACPI: ACPI bus type pnp unregistered
[    3.295087] system 00:01: [io  0x0c00-0x0c7f] has been reserved
[    3.306598] pci 0000:00:1c.0: BAR 9: assigned [mem 0xf0000000-0xf01fffff 64bit pref]
[    3.314656] pci 0000:00:1c.5: BAR 9: assigned [mem 0xf0200000-0xf03fffff 64bit pref]
[    3.322712] pci 0000:00:1c.0: BAR 7: assigned [io  0x1000-0x1fff]
[    3.328979] pci 0000:00:1c.5: BAR 7: assigned [io  0x2000-0x2fff]
[    3.335251] pci 0000:00:1f.2: BAR 5: assigned [mem 0x000a0000-0x000a07ff]
[    3.342221] pci 0000:00:1f.2: BAR 5: set to [mem 0x000a0000-0x000a07ff] (PCI address [0xa0000-0xa07ff]
[    3.351838] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[    3.357243] pci 0000:00:01.0:   bridge window [io  0xd000-0xdfff]
[    3.363513] pci 0000:00:01.0:   bridge window [mem 0xfa000000-0xfdefffff]
[    3.370475] pci 0000:00:01.0:   bridge window [mem 0xd0000000-0xdfffffff 64bit pref]
[    3.378533] pci 0000:00:06.0: PCI bridge to [bus 02-02]
[    3.383934] pci 0000:00:06.0:   bridge window [io  disabled]
[    3.389768] pci 0000:00:06.0:   bridge window [mem disabled]
[    3.395602] pci 0000:00:06.0:   bridge window [mem pref disabled]
[    3.401870] pci 0000:00:1c.0: PCI bridge to [bus 03-03]
[    3.407272] pci 0000:00:1c.0:   bridge window [io  0x1000-0x1fff]
[    3.413545] pci 0000:00:1c.0:   bridge window [mem 0xf9f00000-0xf9ffffff]
[    3.420507] pci 0000:00:1c.0:   bridge window [mem 0xf0000000-0xf01fffff 64bit pref]
[    3.428565] pci 0000:00:1c.5: PCI bridge to [bus 04-04]
[    3.433967] pci 0000:00:1c.5:   bridge window [io  0x2000-0x2fff]
[    3.440243] pci 0000:00:1c.5:   bridge window [mem 0xf9e00000-0xf9efffff]
[    3.447216] pci 0000:00:1c.5:   bridge window [mem 0xf0200000-0xf03fffff 64bit pref]
[    3.455284] pci 0000:00:1e.0: PCI bridge to [bus 05-05]
[    3.460684] pci 0000:00:1e.0:   bridge window [io  disabled]
[    3.466521] pci 0000:00:1e.0:   bridge window [mem 0xf9d00000-0xf9dfffff]
[    3.473482] pci 0000:00:1e.0:   bridge window [mem pref disabled]
[    3.479761] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    3.486642] pci 0000:00:06.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    3.493522] pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    3.500405] pci 0000:00:1c.5: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[    3.507380] NET: Registered protocol family 2
[    3.512119] IP route cache hash table entries: 262144 (order: 9, 2097152 bytes)
[    3.521096] TCP established hash table entries: 524288 (order: 11, 8388608 bytes)
[    3.533682] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[    3.541205] TCP: Hash tables configured (established 524288 bind 65536)
[    3.547992] TCP reno registered
[    3.551328] UDP hash table entries: 4096 (order: 5, 131072 bytes)
[    3.557692] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes)
[    3.564605] NET: Registered protocol family 1
[    3.569393] RPC: Registered udp transport module.
[    3.574277] RPC: Registered tcp transport module.
[    3.579169] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    4.697020] pci 0000:00:1d.7: EHCI: BIOS handoff failed (BIOS bug?) 01010001
[    4.704420] Trying to unpack rootfs image as initramfs...
[    4.775041] Freeing initd memory: 3460k .780660] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[    4.787274] Placing 64MB software IO TLB between ffff8800021b2000 - ffff8800061b2000
[    4.795318] software IO TLB at phys 0x21b2000 - 0x61b2000
[    4.801172] Simple Boot Flag at 0x7a set to 0x1
[    4.808171] microcode: CPU0 sig=0x6fb, pf=0x10, revision=0xb3
[    4.814092] microcode: CPU1 sig=0x6fb, pf=0x10, revision=0xb3
[    4.820019] microcode: CPU2 sig=0x6fb, pf=0x10, revision=0xb3
[    4.829512] microcode: CPU3 sig=0x6fb, pf=0x10, revision=0xb3
[    4.835510] microcode: Microcode Update Driver: v2.00 <[email protected]>, Peter Oruba
[    4.845020] audit: initializing netlink socket (disabled)
[    4.850601] type=2000 audit(1270582130.850:1): initialized
[    4.876011] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[    4.886784] VFS: Disk quotas dquot_6.5.2
[    4.890993] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    4.898953] msgmni has been set to 11828
[    4.903830] alg: No test for stdrng (krng)
[    4.908268] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[    4.915973] io scheduler noop registered
[    4.920067] io scheduler deadline registered
[    4.924679] io scheduler cfq registered (default)
[    4.930754] pcieport 0000:00:01.0: Requesting control of PCIe PME from ACPI BIOS
[    4.938482] pcieport 0000:00:01.0: Failed to receive control of PCIe PME service: no _OSC support
[    4.947653] pcie_pme: probe of 0000:00:01.0:pcie01 failed with error -13
[    4.954521] pcieport 0000:00:06.0: Requesting control of PCIe PME from ACPI BIOS
[    4.962240] pcieport 0000:00:06.0: Failed to receive control of PCIe PME service: no _OSC support
[    4.971428] pcie_pme: probe of 0000:00:06.0:pcie01 failed with error -13
[    4.978315] pcieport 0000:00:1c.0: Requesting control of PCIe PME from ACPI BIOS
[    4.986013] pcieport 0000:00:1c.0: Failed to receive control of PCIe PME service: no _OSC support
[    4.995193] pcie_pme: probe of 0000:00:1c.0:pcie01 failed with error -13
[    5.002062] pcieport 0000:00:1c.5: Requesting control of PCIe PME from ACPI BIOS
[    5.009764] pcieport 0000:00:1c.5: Failed to receive control of PCIe PME service: no _OSC support
[    5.018932] pcie_pme: probe of 0000:00:1c.5:pcie01 failed with error -13
[    5.025919] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    5.032111] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
[    5.040772] ACPI: Power Button [VBTN]
[    5.044713] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[    5.052435] ACPI: Power Button [PWRF]
[    5.155976] Non-volatile memory driver v1.3
[    5.160343] Linux agpgart interface v0.103
[    5.164843] [drm] Initialized drm 1.1.0 20060810
[    5.169632] [drm:i915_init] *ERROR* drm/i915 can't work without intel_agp module!
[    5.177426] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    5.428358] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    5.435172] 00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    5.443890] brd: module loaded
[    5.448507] loop: module loaded
[    5.451955] Loading iSCSI transport class v2.0-870.
[    5.457687] ahci 0000:00:1f.2: PCI INT C -> GSI 20 (level, low) -> IRQ 20
[    5.464777] ahci: SSS flag set, parallel bus scan disabled
[    6.472019] ahci 0000:00:1f.2: controller reset failed (0xffffffff)
[    6.478474] ahci 0000:00:1f.2: PCI INT C disabled
[    6.483349] ahci: probe of 0000:00:1f.2 failed with error -5

-andy

#1 lore raw
Quoted 9 lines · Andy Isaacson

This Dell Precision WorkStation T3400 doesn't boot 2.6.34-rc1 (tried 522dba71). 2.6.33 was fine, and it's been running various stable kernels for the last 18 months. Unfortunately I can't reasonably bisect as I need this machine to be usable, but I can test specific patches or options. (three or four reboots is fine, 15 is not.)

full dmesg from failing boot and a successful boot at
http://web.hexapodia.org/~adi/tmp/20100406-pci-ahci-reset-fail/

Quoted 7 lines

I suspect it's due to:

[    3.094038] pci 0000:00:1f.2: no compatible bridge window for [mem 0xff970000-0xff9707ff]
[    3.103001] pci 0000:00:1f.2: can't reserve [mem 0xff970000-0xff9707ff]

so I've CCed a few recent committers to setup-res.c.

can you try to boot with pci=nocrs ?

also please check with -rc4.

YH

#2 lore raw
Quoted 6 lines · Yinghai
Quoted 4 lines
[    3.094038] pci 0000:00:1f.2: no compatible bridge window for [mem 0xff970000-0xff9707ff]
[    3.103001] pci 0000:00:1f.2: can't reserve [mem 0xff970000-0xff9707ff]

so I've CCed a few recent committers to setup-res.c.

can you try to boot with pci=nocrs ?

That boots and configures the AHCI just fine.

Quoted 1 line

also please check with -rc4.

All I see in git is -rc3 + 299 commits ending with 0fdf867...

That still fails with the same "controller reset failed" message from ahci.

-andy

#3 lore raw
Quoted 8 lines · Andy Isaacson
Quoted 6 lines · Yinghai
Quoted 4 lines

[    3.094038] pci 0000:00:1f.2: no compatible bridge window for [mem 0xff970000-0xff9707ff] [    3.103001] pci 0000:00:1f.2: can't reserve [mem 0xff970000-0xff9707ff]

so I've CCed a few recent committers to setup-res.c.

can you try to boot with pci=nocrs ?

Quoted 8 lines

That boots and configures the AHCI just fine.

Quoted 1 line

also please check with -rc4.

All I see in git is -rc3 + 299 commits ending with 0fdf867...

That still fails with the same "controller reset failed" message from ahci.

please file bug and assign to Bjorn.

YH

#4 lore raw
In reply to Andy Isaacson
Quoted 6 lines · Andy Isaacson

This Dell Precision WorkStation T3400 doesn't boot 2.6.34-rc1 (tried 522dba71). 2.6.33 was fine, and it's been running various stable kernels for the last 18 months. Unfortunately I can't reasonably bisect as I need this machine to be usable, but I can test specific patches or options. (three or four reboots is fine, 15 is not.)

Quoted 7 lines

full dmesg from failing boot and a successful boot at
http://web.hexapodia.org/~adi/tmp/20100406-pci-ahci-reset-fail/

I suspect it's due to:

[    3.094038] pci 0000:00:1f.2: no compatible bridge window for [mem 0xff970000-0xff9707ff]
[    3.103001] pci 0000:00:1f.2: can't reserve [mem 0xff970000-0xff9707ff]

Thanks a lot for reporting this!

No need to bisect it. I'm pretty sure 2.6.34-rc1 will boot fine if you use "pci=use_crs" (obviously that's only a temporary workaround until we fix the real problem).

The BIOS apparently reported this window:

pci_root PNP0A03:00: host bridge window [mem 0xff97c000-0xff97ffff]

which doesn't enclose the [mem 0xff970000-0xff9707ff] region where BIOS put AHCI device, so we moved the AHCI device. Unfortunately, we put it at [mem 0x000a0000-0x000a07ff], which wasn't a very good choice because that's probably already used by a VGA device.

If you happen to have Windows on this box, I'd love to know whether *it* moves the AHCI device, too, or whether Windows interprets the BIOS information differently than we do. If you have Windows and can collect screenshots of the Device Manager resources for the PCI bus and the AHCI controller, that would be a good start.

Would you mind trying the patch below and the patch and kernel args here:
https://bugzilla.kernel.org/show_bug.cgi?id=15533#c5

This will (1) reserve the VGA area, so we should put the AHCI device elsewhere, and (2) collect a few more details about exactly what the BIOS is reporting.

Bjorn

commit 46b6e80aae2ec1d073767c92bba1d98896bce700

Author: Bjorn Helgaas <[email protected]>
Date:   Tue Apr 6 21:44:12 2010 -0600
arch/x86/include/asm/setup.h +0 -1
index 86b1506..f4c0fe4 100644
@@ -44,7 +44,6 @@ static inline void visws_early_detect(void) { }
 extern unsigned long saved_video_mode;
 
 extern void reserve_standard_io_resources(void);
-extern void i386_reserve_resources(void);
 extern void setup_default_timer_irq(void);
 
 #ifdef CONFIG_X86_MRST
arch/x86/kernel/head32.c +0 -1
index b2e2460..966b37f 100644
@@ -22,7 +22,6 @@ static void __init i386_default_early_setup(void)
 {
 	/* Initilize 32bit specific setup functions */
 	x86_init.resources.probe_roms = probe_roms;
-	x86_init.resources.reserve_resources = i386_reserve_resources;
 	x86_init.mpparse.setup_ioapic_ids = setup_ioapic_ids_from_mpc;
 
 	reserve_ebda_region();
arch/x86/kernel/setup.c +8 -17
index 9570541..24d9113 100644
@@ -575,6 +575,13 @@ static struct resource standard_io_resources[] = {
 		.flags = IORESOURCE_BUSY | IORESOURCE_IO }
 };
 
+static struct resource video_ram_resource = {
+	.name	= "Video RAM area",
+	.start	= 0xa0000,
+	.end	= 0xbffff,
+	.flags	= IORESOURCE_BUSY | IORESOURCE_MEM
+};
+
 void __init reserve_standard_io_resources(void)
 {
 	int i;
@@ -583,6 +590,7 @@ void __init reserve_standard_io_resources(void)
 	for (i = 0; i < ARRAY_SIZE(standard_io_resources); i++)
 		request_resource(&ioport_resource, &standard_io_resources[i]);
 
+	request_resource(&iomem_resource, &video_ram_resource);
 }
 
 /*
@@ -1042,20 +1050,3 @@ void __init setup_arch(char **cmdline_p)
 
 	mcheck_init();
 }
-
-#ifdef CONFIG_X86_32
-
-static struct resource video_ram_resource = {
-	.name	= "Video RAM area",
-	.start	= 0xa0000,
-	.end	= 0xbffff,
-	.flags	= IORESOURCE_BUSY | IORESOURCE_MEM
-};
-
-void __init i386_reserve_resources(void)
-{
-	request_resource(&iomem_resource, &video_ram_resource);
-	reserve_standard_io_resources();
-}
-
-#endif /* CONFIG_X86_32 */
#5 lore raw
Quoted 10 lines · Bjorn Helgaas
Quoted 4 lines

I suspect it's due to:

[    3.094038] pci 0000:00:1f.2: no compatible bridge window for [mem 0xff970000-0xff9707ff]
[    3.103001] pci 0000:00:1f.2: can't reserve [mem 0xff970000-0xff9707ff]

Thanks a lot for reporting this!

No need to bisect it. I'm pretty sure 2.6.34-rc1 will boot fine if you use "pci=use_crs" (obviously that's only a temporary workaround until we fix the real problem).

pci=nocrs worked on 2.6.34-rc3-00299-g0fdf867. I won't be back in front of the machine to try use_crs until Thursday.

Quoted 3 lines

put AHCI device, so we moved the AHCI device. Unfortunately, we put it at [mem 0x000a0000-0x000a07ff], which wasn't a very good choice because that's probably already used by a VGA device.

The machine has one VGA controller exposed currently; there may be another integrated Intel video controller on the motherboard and disabled by the BIOS.

01:00.0 VGA compatible controller: nVidia Corporation Quadro NVS 290 (rev a1) (prog-if 00 [VGA controller])

        Subsystem: nVidia Corporation Device 0492
        Flags: bus master, fast devsel, latency 0, IRQ 16
        Memory at fc000000 (32-bit, non-prefetchable) [size=16M]
        Memory at d0000000 (64-bit, prefetchable) [size=256M]
        Memory at fa000000 (64-bit, non-prefetchable) [size=32M]
        I/O ports at dc80 [size=128]
        Expansion ROM at fde00000 [disabled] [size=128K]
        Capabilities: <access denied>
        Kernel driver in use: nouveau

(this is from the pci=nocrs boot.)

Quoted 5 lines

If you happen to have Windows on this box, I'd love to know whether *it* moves the AHCI device, too, or whether Windows interprets the BIOS information differently than we do. If you have Windows and can collect screenshots of the Device Manager resources for the PCI bus and the AHCI controller, that would be a good start.

The machine only has Linux installed, but I may have access to another T3400 that can dual-boot. Any preference for XP versus Win7?

Quoted 7 lines

Would you mind trying the patch below and the patch and kernel args here:
https://bugzilla.kernel.org/show_bug.cgi?id=15533#c5

This will (1) reserve the VGA area, so we should put the AHCI device elsewhere, and (2) collect a few more details about exactly what the BIOS is reporting.

I'll try that on Thursday.

-andy

#6 lore raw
Quoted 6 lines · Andy Isaacson
Quoted 5 lines · Bjorn Helgaas
Quoted 4 lines

I suspect it's due to:

[    3.094038] pci 0000:00:1f.2: no compatible bridge window for [mem 0xff970000-0xff9707ff]
[    3.103001] pci 0000:00:1f.2: can't reserve [mem 0xff970000-0xff9707ff]
Quoted 8 lines
Quoted 5 lines

Thanks a lot for reporting this!

No need to bisect it. I'm pretty sure 2.6.34-rc1 will boot fine if you use "pci=use_crs" (obviously that's only a temporary workaround until we fix the real problem).

pci=nocrs worked on 2.6.34-rc3-00299-g0fdf867. I won't be back in front of the machine to try use_crs until Thursday.

Oops, sorry, I meant it would probably work with "pci=nocrs", as you already confirmed. Don't bother trying "pci=use_crs"; that's turned on automatically on your system already.

Quoted 8 lines
Quoted 5 lines

If you happen to have Windows on this box, I'd love to know whether *it* moves the AHCI device, too, or whether Windows interprets the BIOS information differently than we do. If you have Windows and can collect screenshots of the Device Manager resources for the PCI bus and the AHCI controller, that would be a good start.

The machine only has Linux installed, but I may have access to another T3400 that can dual-boot. Any preference for XP versus Win7?

Nope, whatever's more convenient for you should be fine.

Quoted 9 lines
Quoted 7 lines

Would you mind trying the patch below and the patch and kernel args here:
https://bugzilla.kernel.org/show_bug.cgi?id=15533#c5

This will (1) reserve the VGA area, so we should put the AHCI device elsewhere, and (2) collect a few more details about exactly what the BIOS is reporting.

I'll try that on Thursday.

Great, thanks! Oh, and I forgot to ask: what BIOS version are you running? Google found several reports of USB issues in Windows on this box, e.g., http://tim.cexx.org/?p=529 .

I think we still have a Linux bug in that we should be reserving the legacy VGA area, but if the BIOS is reporting an incorrect host bridge window, that will cause us to move the AHCI controller and tickle this bug when we wouldn't otherwise.

Bjorn

#7 lore raw
Quoted 4 lines · Bjorn Helgaas
Quoted 2 lines

The machine only has Linux installed, but I may have access to another T3400 that can dual-boot. Any preference for XP versus Win7?

Nope, whatever's more convenient for you should be fine.

On another T3400 with BIOS A03, Win7's Device Manager -> IDE ATA/ATAPI controllers -> Standard AHCI 1.0 -> Resources -> Memory Range setting is ff97f800-ff97ffff. (If that's not the info you needed, let me know where I need to look to get the answer.)

Quoted 4 lines
Quoted 4 lines
Quoted 4 lines

Would you mind trying the patch below and the patch and kernel args here:
https://bugzilla.kernel.org/show_bug.cgi?id=15533#c5

Quoted 8 lines
Quoted 5 lines
Quoted 3 lines

This will (1) reserve the VGA area, so we should put the AHCI device elsewhere, and (2) collect a few more details about exactly what the BIOS is reporting.

I'll try that on Thursday.

Great, thanks! Oh, and I forgot to ask: what BIOS version are you running?

BIOS Information
Vendor: Dell Inc.
Version: A04
Release Date: 03/21/2008

Quoted 4 lines

I think we still have a Linux bug in that we should be reserving the legacy VGA area, but if the BIOS is reporting an incorrect host bridge window, that will cause us to move the AHCI controller and tickle this bug when we wouldn't otherwise.

I'll try the debug patch tomorrow morning.

-andy

#8 lore raw
Quoted 9 lines · Andy Isaacson
Quoted 4 lines · Bjorn Helgaas
Quoted 2 lines

The machine only has Linux installed, but I may have access to another T3400 that can dual-boot. Any preference for XP versus Win7?

Nope, whatever's more convenient for you should be fine.

On another T3400 with BIOS A03, Win7's Device Manager -> IDE ATA/ATAPI controllers -> Standard AHCI 1.0 -> Resources -> Memory Range setting is ff97f800-ff97ffff.

Assuming this is the same AHCI controller (probably is, because I only see one mentioned in your logs), I think Win7 moved it from where BIOS left it. It probably started at 0xff970000, and Win7 moved it into one of the host bridge windows (but not the legacy VGA one):

pci_root PNP0A03:00: host bridge window [mem 0xff980800-0xff980bff] pci_root PNP0A03:00: host bridge window [mem 0xff97c000-0xff97ffff] pci 0000:00:1f.2: no compatible bridge window for [mem 0xff970000-0xff9707ff]

Bjorn

#9 lore raw
Quoted 5 lines · Bjorn Helgaas
Quoted 4 lines · Andy Isaacson
Quoted 3 lines · Bjorn Helgaas
Quoted 2 lines

The machine only has Linux installed, but I may have access to another T3400 that can dual-boot. Any preference for XP versus Win7?

Quoted 8 lines
Quoted 5 lines
Quoted 1 line

Nope, whatever's more convenient for you should be fine.

On another T3400 with BIOS A03, Win7's Device Manager -> IDE ATA/ATAPI controllers -> Standard AHCI 1.0 -> Resources -> Memory Range setting is ff97f800-ff97ffff.

Assuming this is the same AHCI controller (probably is, because I only see one mentioned in your logs), I think Win7 moved it from where BIOS

Yes, there's only one AHCI controller mentioned on either machine.

-andy

#10 lore raw
In reply to Bjorn Helgaas
Quoted 7 lines · Bjorn Helgaas

Would you mind trying the patch below and the patch and kernel args here:
https://bugzilla.kernel.org/show_bug.cgi?id=15533#c5

This will (1) reserve the VGA area, so we should put the AHCI device elsewhere, and (2) collect a few more details about exactly what the BIOS is reporting.

We established that the patch in the message above wasn't enough (the patch reserved 0xa0000-0xbffff, and Linux moved the AHCI controller to 0xc0000 instead of 0xa0000).

But I'd still like to see the details of what ACPI is telling us, so if you wouldn't mind trying that patch from bugzilla:
https://bugzilla.kernel.org/show_bug.cgi?id=15533#c5
and collecting an acpidump, and attaching both to the bug report:
https://bugzilla.kernel.org/show_bug.cgi?id=15744
that would be great.

Linux thinks the windows are:
pci_root PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff] pci_root PNP0A03:00: host bridge window [mem 0x000c0000-0x000effff] pci_root PNP0A03:00: host bridge window [mem 0x000f0000-0x000fffff]

The 0xa0000-0xbffff one makes good sense. That's normally MMIO that's routed via PCI to the VGA device frame buffer, and we should be able to figure out how to avoid that area, e.g., by using BIOS info, PCI class codes, etc.

Now we need to figure how to avoid the 0xc0000-0xeffff and 0xf0000-0xfffff windows. Maybe there's something special about how ACPI describes them.

Or maybe we're just unlucky because these are the first windows in the _CRS list, and Linux tries them in order, while Windows uses a different strategy.

Bjorn

#11 lore raw
Quoted 6 lines · Bjorn Helgaas

But I'd still like to see the details of what ACPI is telling us, so if you wouldn't mind trying that patch from bugzilla:
https://bugzilla.kernel.org/show_bug.cgi?id=15533#c5
and collecting an acpidump, and attaching both to the bug report:
https://bugzilla.kernel.org/show_bug.cgi?id=15744
that would be great.

That's confusing, I think I figured it out but "try this patch" which links to a message that refers to another patch and some commandline options and some config options and doesn't say what the goal is, is a lot for me to parse since I don't actually understand what's going on here.

I think I got it all:
https://bugzilla.kernel.org/attachment.cgi?id=25969
https://bugzilla.kernel.org/attachment.cgi?id=25970

Let me know (using small words if necessary) if I screwed something up.

Thanks,
-andy

#12 lore raw
In reply to Bjorn Helgaas
Quoted 10 lines · Bjorn Helgaas

Linux thinks the windows are:
pci_root PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff] pci_root PNP0A03:00: host bridge window [mem 0x000c0000-0x000effff] pci_root PNP0A03:00: host bridge window [mem 0x000f0000-0x000fffff]

The 0xa0000-0xbffff one makes good sense. That's normally MMIO that's routed via PCI to the VGA device frame buffer, and we should be able to figure out how to avoid that area, e.g., by using BIOS info, PCI class codes, etc.

Quoted 6 lines

Now we need to figure how to avoid the 0xc0000-0xeffff and 0xf0000-0xfffff windows. Maybe there's something special about how ACPI describes them.

Or maybe we're just unlucky because these are the first windows in the _CRS list, and Linux tries them in order, while Windows uses a different strategy.

Perhaps it's sufficient to try them in reverse order?

#13 lore raw
Quoted 11 lines · Matthew Wilcox
Quoted 10 lines · Bjorn Helgaas

Linux thinks the windows are:
pci_root PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff] pci_root PNP0A03:00: host bridge window [mem 0x000c0000-0x000effff] pci_root PNP0A03:00: host bridge window [mem 0x000f0000-0x000fffff]

The 0xa0000-0xbffff one makes good sense. That's normally MMIO that's routed via PCI to the VGA device frame buffer, and we should be able to figure out how to avoid that area, e.g., by using BIOS info, PCI class codes, etc.

Quoted 8 lines
Quoted 6 lines

Now we need to figure how to avoid the 0xc0000-0xeffff and 0xf0000-0xfffff windows. Maybe there's something special about how ACPI describes them.

Or maybe we're just unlucky because these are the first windows in the _CRS list, and Linux tries them in order, while Windows uses a different strategy.

Perhaps it's sufficient to try them in reverse order?

Why bother? The first megabyte is really special in x86... it is historically used for legacy devices, it has specific functions for PCI firmware, and it has separate MTRRs.

Simply put, "there there be dragons". There is no sane reason to allocate unassigned devices there (preassigned devices is another matter).

-hpa

Signature · 2 lines
H. Peter Anvin, Intel Open Source Technology Center
I work for Intel.  I don't speak on their behalf.
#14 lore raw
In reply to Bjorn Helgaas
Quoted 11 lines · Bjorn Helgaas

Linux thinks the windows are:
pci_root PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff] pci_root PNP0A03:00: host bridge window [mem 0x000c0000-0x000effff] pci_root PNP0A03:00: host bridge window [mem 0x000f0000-0x000fffff]

The 0xa0000-0xbffff one makes good sense. That's normally MMIO that's routed via PCI to the VGA device frame buffer, and we should be able to figure out how to avoid that area, e.g., by using BIOS info, PCI class codes, etc.

Quoted 7 lines

Now we need to figure how to avoid the 0xc0000-0xeffff and 0xf0000-0xfffff windows. Maybe there's something special about how ACPI describes them.

Or maybe we're just unlucky because these are the first windows in the _CRS list, and Linux tries them in order, while Windows uses a different strategy.

I strongly suspects that Windows knows that < 1 MB is special, and only ever assigns it upon explicit allocation.

-hpa

Signature · 2 lines
H. Peter Anvin, Intel Open Source Technology Center
I work for Intel.  I don't speak on their behalf.
#15 lore raw
In reply to Andy Isaacson
Quoted 6 lines · On środa, 7 kwietnia 2010 o 00:54:25 Andy Isaacson wrote:

This Dell Precision WorkStation T3400 doesn't boot 2.6.34-rc1 (tried 522dba71). 2.6.33 was fine, and it's been running various stable kernels for the last 18 months. Unfortunately I can't reasonably bisect as I need this machine to be usable, but I can test specific patches or options. (three or four reboots is fine, 15 is not.)

I created a Bugzilla entry at
https://bugzilla.kernel.org/show_bug.cgi?id=15744
for your bug report, please add your address to the CC list in there, thanks!

Signature · 2 lines
Maciej Rutecki
http://www.maciek.unixy.pl