Skip to contentSkip to conversation

powerpc/85xx: Add eTSEC 2.0 support for P1020RDB boards

PATCH Applied Anton Vorontsov 4 participants 7 messages Apr 15, 2010 – May 25, 2010

Subsystems (3)
Device tree bindings PowerPC Linux for PowerPC embedded PPC85XX
lore
Share & tools
lore

Anton Vorontsov

author
#0 lore raw

PATCH 1/1 powerpc/85xx: Add eTSEC 2.0 support for P1020RDB boards

This patch adds support for eTSEC 2.0 as found in P1020. The changes include introduction of the group nodes for the etsec nodes.

Signed-off-by Sandeep Gopalpet <[email protected]>
Signed-off-by Anton Vorontsov <[email protected]>

---

This is based on
http://www.bitshrine.org/gpp/kernel-2.6.32-rc3-P1020RDB-DTS-Support-for-eTSEC-2.0-v0.patch
but revamped for the mainline's OF bindings.

 arch/powerpc/boot/dts/p1020rdb.dts |  119 ++++++++++++++++++++++++++++++++++++
 1 files changed, 119 insertions(+), 0 deletions(-)
arch/powerpc/boot/dts/p1020rdb.dts +119 -0
index df52690..49848c5 100644
@@ -19,6 +19,9 @@
 	aliases {
 		serial0 = &serial0;
 		serial1 = &serial1;
+		ethernet0 = &enet0;
+		ethernet1 = &enet1;
+		ethernet2 = &enet2;
 		pci0 = &pci0;
 		pci1 = &pci1;
 	};

@@ -346,6 +349,122 @@
 			};
 		};
 
+		mdio@24000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "fsl,etsec2-mdio";
+			reg = <0x24000 0x1000 0xb0030 0x4>;
+
+			phy0: ethernet-phy@0 {
+				interrupt-parent = <&mpic>;
+				interrupts = <3 1>;
+				reg = <0x0>;
+			};
+
+			phy1: ethernet-phy@1 {
+				interrupt-parent = <&mpic>;
+				interrupts = <2 1>;
+				reg = <0x1>;
+			};
+		};
+
+		mdio@25000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "fsl,etsec2-tbi";
+			reg = <0x25000 0x1000 0xb1030 0x4>;
+
+			tbi0: tbi-phy@11 {
+				reg = <0x11>;
+				device_type = "tbi-phy";
+			};
+		};
+
+		enet0: ethernet@b0000 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			device_type = "network";
+			model = "eTSEC";
+			compatible = "fsl,etsec2";
+			fsl,num_rx_queues = <0x8>;
+			fsl,num_tx_queues = <0x8>;
+			local-mac-address = [ 00 00 00 00 00 00 ];
+			interrupt-parent = <&mpic>;
+			fixed-link = <1 1 1000 0 0>;
+			phy-connection-type = "rgmii-id";
+
+			queue-group@0 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				reg = <0xb0000 0x1000>;
+				interrupts = <29 2 30 2 34 2>;
+			};
+
+			queue-group@1 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				reg = <0xb4000 0x1000>;
+				interrupts = <17 2 18 2 24 2>;
+			};
+		};
+
+		enet1: ethernet@b1000 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			device_type = "network";
+			model = "eTSEC";
+			compatible = "fsl,etsec2";
+			fsl,num_rx_queues = <0x8>;
+			fsl,num_tx_queues = <0x8>;
+			local-mac-address = [ 00 00 00 00 00 00 ];
+			interrupt-parent = <&mpic>;
+			phy-handle = <&phy0>;
+			tbi-handle = <&tbi0>;
+			phy-connection-type = "sgmii";
+
+			queue-group@0 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				reg = <0xb1000 0x1000>;
+				interrupts = <35 2 36 2 40 2>;
+			};
+
+			queue-group@1 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				reg = <0xb5000 0x1000>;
+				interrupts = <51 2 52 2 67 2>;
+			};
+		};
+
+		enet2: ethernet@b2000 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			device_type = "network";
+			model = "eTSEC";
+			compatible = "fsl,etsec2";
+			fsl,num_rx_queues = <0x8>;
+			fsl,num_tx_queues = <0x8>;
+			local-mac-address = [ 00 00 00 00 00 00 ];
+			interrupt-parent = <&mpic>;
+			phy-handle = <&phy1>;
+			phy-connection-type = "rgmii-id";
+
+			queue-group@0 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				reg = <0xb2000 0x1000>;
+				interrupts = <31 2 32 2 33 2>;
+			};
+
+			queue-group@1 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				reg = <0xb6000 0x1000>;
+				interrupts = <25 2 26 2 27 2>;
+			};
+		};
+
 		usb@22000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
Signature · 1 line
1.7.0.3
#1 lore raw

Hi Anton,

Quoted 4 lines · Anton Vorontsov

This patch adds support for eTSEC 2.0 as found in P1020. The changes include introduction of the group nodes for the etsec nodes.

Quoted 10 lines
Signed-off-by Sandeep Gopalpet<[email protected]>
Signed-off-by Anton Vorontsov<[email protected]>

---

This is based on
http://www.bitshrine.org/gpp/kernel-2.6.32-rc3-P1020RDB-DTS-Support-for-eTSEC-2.0-v0.patch
but revamped for the mainline's OF bindings.

Thanks a lot, I appreciate your help.

Felix.

Applied
#2 lore raw
In reply to Anton Vorontsov
Quoted 10 lines · Anton Vorontsov

This patch adds support for eTSEC 2.0 as found in P1020. The changes include introduction of the group nodes for the etsec nodes.
=20

Signed-off-by Sandeep Gopalpet <[email protected]>
Signed-off-by Anton Vorontsov <[email protected]>

---
=20
This is based on
=

http://www.bitshrine.org/gpp/kernel-2.6.32-rc3-P1020RDB-DTS-Support-for-eT=
SEC-2.0-v0.patch

Quoted 3 lines

but revamped for the mainline's OF bindings.
=20
arch/powerpc/boot/dts/p1020rdb.dts | 119 =

++++++++++++++++++++++++++++++++++++

Quoted 1 line
1 files changed, 119 insertions(+), 0 deletions(-)

applied to next

- k=

#3 lore raw

PATCH 1/1 powerpc/85xx: Add P1021MDS board support

P1021 is a dual e500v2 core based SOC with:
* 3 eTSECs (eTSEC1/3 RGMII, eTSEC2 SGMII on this board)
* 2 PCIe Controller
* 1 USB2.0 controller
* eSDHC, eSPI, I2C, DUART
* eLBC (NAND, BCSR, PMC0/1)
* Security Engine (SEC 3.3.2)
* Quicc Engine (QE)

Signed-off-by Haiying Wang <[email protected]>
Signed-off-by Yu Liu <[email protected]>
---
 arch/powerpc/boot/dts/p1021mds.dts        |  698 +++++++++++++++++++++++++++++
 arch/powerpc/platforms/85xx/mpc85xx_mds.c |   99 ++++-
 2 files changed, 794 insertions(+), 3 deletions(-)
 create mode 100644 arch/powerpc/boot/dts/p1021mds.dts
arch/powerpc/boot/dts/p1021mds.dts new file +698 -0
new file mode 100644
index 0000000..7fad2df
@@ -0,0 +1,698 @@
+/*
+ * P1021 MDS Device Tree Source
+ *
+ * Copyright 2010 Freescale Semiconductor Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+/dts-v1/;
+/ {
+	model = "fsl,P1021";
+	compatible = "fsl,P1021MDS";
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	aliases {
+		serial0 = &serial0;
+		serial1 = &serial1;
+		ethernet0 = &enet0;
+		ethernet1 = &enet1;
+		ethernet2 = &enet2;
+		ethernet3 = &enet3;
+		ethernet4 = &enet4;
+		pci0 = &pci0;
+		pci1 = &pci1;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		PowerPC,P1021@0 {
+			device_type = "cpu";
+			reg = <0x0>;
+			next-level-cache = <&L2>;
+		};
+
+		PowerPC,P1021@1 {
+			device_type = "cpu";
+			reg = <0x1>;
+			next-level-cache = <&L2>;
+		};
+	};
+
+	memory {
+		device_type = "memory";
+	};
+
+	localbus@ffe05000 {
+		#address-cells = <2>;
+		#size-cells = <1>;
+		compatible = "fsl,p1021-elbc", "fsl,elbc", "simple-bus";
+		reg = <0 0xffe05000 0 0x1000>;
+		interrupts = <19 2>;
+		interrupt-parent = <&mpic>;
+
+		/* NAND Flash, BCSR, PMC0/1*/
+		ranges = <0x0 0x0 0x0 0xfc000000 0x02000000
+			  0x1 0x0 0x0 0xf8000000 0x00008000
+			  0x2 0x0 0x0 0xf8010000 0x00020000
+			  0x3 0x0 0x0 0xf8020000 0x00020000>;
+
+		nand@0,0 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "fsl,p1021-fcm-nand",
+				     "fsl,elbc-fcm-nand";
+			reg = <0x0 0x0 0x40000>;
+
+			partition@0 {
+				/* This location must not be altered  */
+				/* 1MB for u-boot Bootloader Image */
+				reg = <0x0 0x00100000>;
+				label = "NAND (RO) U-Boot Image";
+				read-only;
+			};
+
+			partition@100000 {
+				/* 1MB for DTB Image */
+				reg = <0x00100000 0x00100000>;
+				label = "NAND (RO) DTB Image";
+				read-only;
+			};
+
+			partition@200000 {
+				/* 4MB for Linux Kernel Image */
+				reg = <0x00200000 0x00400000>;
+				label = "NAND (RO) Linux Kernel Image";
+				read-only;
+			};
+
+			partition@600000 {
+				/* 5MB for Compressed Root file System Image */
+				reg = <0x00600000 0x00500000>;
+				label = "NAND (RO) Compressed RFS Image";
+				read-only;
+			};
+
+			partition@b00000 {
+				/* 6MB for JFFS2 based Root file System */
+				reg = <0x00a00000 0x00600000>;
+				label = "NAND (RW) JFFS2 Root File System";
+			};
+
+			partition@1100000 {
+				/* 14MB for JFFS2 based Root file System */
+				reg = <0x01100000 0x00e00000>;
+				label = "NAND (RW) Writable User area";
+			};
+
+			partition@1f00000 {
+				/* 1MB for microcode */
+				reg = <0x01f00000 0x00100000>;
+				label = "NAND (RO) QE Ucode";
+				read-only;
+			};
+		};
+
+		bcsr@1,0 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "fsl,p1021mds-bcsr";
+			reg = <1 0 0x8000>;
+			ranges = <0 1 0 0x8000>;
+		};
+
+		pib@2,0 {
+			compatible = "fsl,p1021mds-pib";
+			reg = <2 0 0x10000>;
+		};
+
+		pib@3,0 {
+			compatible = "fsl,p1021mds-pib";
+			reg = <3 0 0x10000>;
+		};
+	};
+
+	soc@ffe00000 {
+
+		#address-cells = <1>;
+		#size-cells = <1>;
+		device_type = "soc";
+		compatible = "fsl,p1021-immr", "simple-bus";
+		ranges = <0x0  0x0 0xffe00000 0x100000>;
+		bus-frequency = <0>;		// Filled out by uboot.
+
+		ecm-law@0 {
+			compatible = "fsl,ecm-law";
+			reg = <0x0 0x1000>;
+			fsl,num-laws = <12>;
+		};
+
+		ecm@1000 {
+			compatible = "fsl,p1021-ecm", "fsl,ecm";
+			reg = <0x1000 0x1000>;
+			interrupts = <16 2>;
+			interrupt-parent = <&mpic>;
+		};
+
+		memory-controller@2000 {
+			compatible = "fsl,p1021-memory-controller";
+			reg = <0x2000 0x1000>;
+			interrupt-parent = <&mpic>;
+			interrupts = <16 2>;
+		};
+
+		i2c@3000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			cell-index = <0>;
+			compatible = "fsl-i2c";
+			reg = <0x3000 0x100>;
+			interrupts = <43 2>;
+			interrupt-parent = <&mpic>;
+			dfsrr;
+			rtc@68 {
+				compatible = "dallas,ds1374";
+				reg = <0x68>;
+			};
+		};
+
+		i2c@3100 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			cell-index = <1>;
+			compatible = "fsl-i2c";
+			reg = <0x3100 0x100>;
+			interrupts = <43 2>;
+			interrupt-parent = <&mpic>;
+			dfsrr;
+		};
+
+		serial0: serial@4500 {
+			cell-index = <0>;
+			device_type = "serial";
+			compatible = "ns16550";
+			reg = <0x4500 0x100>;
+			clock-frequency = <0>;
+			interrupts = <42 2>;
+			interrupt-parent = <&mpic>;
+		};
+
+		serial1: serial@4600 {
+			cell-index = <1>;
+			device_type = "serial";
+			compatible = "ns16550";
+			reg = <0x4600 0x100>;
+			clock-frequency = <0>;
+			interrupts = <42 2>;
+			interrupt-parent = <&mpic>;
+		};
+
+		spi@7000 {
+			cell-index = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "fsl,espi";
+			reg = <0x7000 0x1000>;
+			interrupts = <59 0x2>;
+			interrupt-parent = <&mpic>;
+			espi,num-ss-bits = <4>;
+			mode = "cpu";
+
+			fsl_m25p80@0 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				compatible = "fsl,espi-flash";
+				reg = <0>;
+				linux,modalias = "fsl_m25p80";
+				spi-max-frequency = <40000000>; /* input clock */
+				partition@u-boot {
+					label = "u-boot-spi";
+					reg = <0x00000000 0x00100000>;
+					read-only;
+				};
+				partition@kernel {
+					label = "kernel-spi";
+					reg = <0x00100000 0x00500000>;
+					read-only;
+				};
+				partition@dtb {
+					label = "dtb-spi";
+					reg = <0x00600000 0x00100000>;
+					read-only;
+				};
+				partition@fs {
+					label = "file system-spi";
+					reg = <0x00700000 0x00900000>;
+				};
+			};
+		};
+
+		gpio: gpio-controller@f000 {
+			#gpio-cells = <2>;
+			compatible = "fsl,mpc8572-gpio";
+			reg = <0xf000 0x100>;
+			interrupts = <47 0x2>;
+			interrupt-parent = <&mpic>;
+			gpio-controller;
+		};
+
+		L2: l2-cache-controller@20000 {
+			compatible = "fsl,p1021-l2-cache-controller";
+			reg = <0x20000 0x1000>;
+			cache-line-size = <32>;	// 32 bytes
+			cache-size = <0x40000>; // L2,256K
+			interrupt-parent = <&mpic>;
+			interrupts = <16 2>;
+		};
+
+		dma@21300 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "fsl,eloplus-dma";
+			reg = <0x21300 0x4>;
+			ranges = <0x0 0x21100 0x200>;
+			cell-index = <0>;
+			dma-channel@0 {
+				compatible = "fsl,eloplus-dma-channel";
+				reg = <0x0 0x80>;
+				cell-index = <0>;
+				interrupt-parent = <&mpic>;
+				interrupts = <20 2>;
+			};
+			dma-channel@80 {
+				compatible = "fsl,eloplus-dma-channel";
+				reg = <0x80 0x80>;
+				cell-index = <1>;
+				interrupt-parent = <&mpic>;
+				interrupts = <21 2>;
+			};
+			dma-channel@100 {
+				compatible = "fsl,eloplus-dma-channel";
+				reg = <0x100 0x80>;
+				cell-index = <2>;
+				interrupt-parent = <&mpic>;
+				interrupts = <22 2>;
+			};
+			dma-channel@180 {
+				compatible = "fsl,eloplus-dma-channel";
+				reg = <0x180 0x80>;
+				cell-index = <3>;
+				interrupt-parent = <&mpic>;
+				interrupts = <23 2>;
+			};
+		};
+
+		usb@22000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "fsl-usb2-dr";
+			reg = <0x22000 0x1000>;
+			interrupt-parent = <&mpic>;
+			interrupts = <28 0x2>;
+			phy_type = "ulpi";
+		};
+
+		 mdio@24000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "fsl,etsec2-mdio";
+			reg = <0x24000 0x1000 0xb0030 0x4>;
+
+			phy0: ethernet-phy@0 {
+				interrupt-parent = <&mpic>;
+				interrupts = <1 1>;
+				reg = <0x0>;
+			};
+			phy1: ethernet-phy@1 {
+				interrupt-parent = <&mpic>;
+				interrupts = <2 1>;
+				reg = <0x1>;
+			};
+			phy4: ethernet-phy@4 {
+				interrupt-parent = <&mpic>;
+				reg = <0x4>;
+			};
+		};
+
+		mdio@25000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "fsl,etsec2-tbi";
+			reg = <0x25000 0x1000 0xb1030 0x4>;
+			tbi0: tbi-phy@11 {
+				reg = <0x11>;
+				device_type = "tbi-phy";
+			};
+		};
+
+		enet0: ethernet@B0000 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			cell-index = <0>;
+			device_type = "network";
+			model = "eTSEC";
+			compatible = "fsl,etsec2";
+			fsl,num_rx_queues = <0x8>;
+			fsl,num_tx_queues = <0x8>;
+			local-mac-address = [ 00 00 00 00 00 00 ];
+			interrupt-parent = <&mpic>;
+			phy-handle = <&phy0>;
+			phy-connection-type = "rgmii-id";
+			queue-group@0{
+				#address-cells = <1>;
+				#size-cells = <1>;
+				reg = <0xB0000 0x1000>;
+				interrupts = <29 2 30 2 34 2>;
+			};
+			queue-group@1{
+				#address-cells = <1>;
+				#size-cells = <1>;
+				reg = <0xB4000 0x1000>;
+				interrupts = <17 2 18 2 24 2>;
+			};
+		};
+
+		enet1: ethernet@B1000 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			cell-index = <0>;
+			device_type = "network";
+			model = "eTSEC";
+			compatible = "fsl,etsec2";
+			fsl,num_rx_queues = <0x8>;
+			fsl,num_tx_queues = <0x8>;
+			local-mac-address = [ 00 00 00 00 00 00 ];
+			interrupt-parent = <&mpic>;
+			phy-handle = <&phy4>;
+			tbi-handle = <&tbi0>;
+			phy-connection-type = "sgmii";
+			queue-group@0{
+				#address-cells = <1>;
+				#size-cells = <1>;
+				reg = <0xB1000 0x1000>;
+				interrupts = <35 2 36 2 40 2>;
+			};
+			queue-group@1{
+				#address-cells = <1>;
+				#size-cells = <1>;
+				reg = <0xB5000 0x1000>;
+				interrupts = <51 2 52 2 67 2>;
+			};
+		};
+
+		enet2: ethernet@B2000 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			cell-index = <0>;
+			device_type = "network";
+			model = "eTSEC";
+			compatible = "fsl,etsec2";
+			fsl,num_rx_queues = <0x8>;
+			fsl,num_tx_queues = <0x8>;
+			local-mac-address = [ 00 00 00 00 00 00 ];
+			interrupt-parent = <&mpic>;
+			phy-handle = <&phy1>;
+			phy-connection-type = "rgmii-id";
+			queue-group@0{
+				#address-cells = <1>;
+				#size-cells = <1>;
+				reg = <0xB2000 0x1000>;
+				interrupts = <31 2 32 2 33 2>;
+			};
+			queue-group@1{
+				#address-cells = <1>;
+				#size-cells = <1>;
+				reg = <0xB6000 0x1000>;
+				interrupts = <25 2 26 2 27 2>;
+			};
+		};
+
+		sdhci@2e000 {
+			compatible = "fsl,p1021-esdhc", "fsl,esdhc";
+			reg = <0x2e000 0x1000>;
+			interrupts = <72 0x2>;
+			interrupt-parent = <&mpic>;
+			/* Filled in by U-Boot */
+			clock-frequency = <0>;
+		};
+
+		crypto@30000 {
+			compatible = "fsl,sec3.3", "fsl,sec3.1",
+				     "fsl,sec3.0", "fsl,sec2.4",
+				     "fsl,sec2.2", "fsl,sec2.1", "fsl,sec2.0";
+			reg = <0x30000 0x10000>;
+			interrupts = <45 2 58 2>;
+			interrupt-parent = <&mpic>;
+			fsl,num-channels = <4>;
+			fsl,channel-fifo-len = <24>;
+			fsl,exec-units-mask = <0x97c>;
+			fsl,descriptor-types-mask = <0x3a30abf>;
+		};
+
+		mpic: pic@40000 {
+			interrupt-controller;
+			#address-cells = <0>;
+			#interrupt-cells = <2>;
+			reg = <0x40000 0x40000>;
+			compatible = "chrp,open-pic";
+			device_type = "open-pic";
+		};
+
+		msi@41600 {
+			compatible = "fsl,p1021-msi", "fsl,mpic-msi";
+			reg = <0x41600 0x80>;
+			msi-available-ranges = <0 0x100>;
+			interrupts = <
+				0xe0 0
+				0xe1 0
+				0xe2 0
+				0xe3 0
+				0xe4 0
+				0xe5 0
+				0xe6 0
+				0xe7 0>;
+			interrupt-parent = <&mpic>;
+		};
+
+		global-utilities@e0000 {	//global utilities block
+			compatible = "fsl,p1021-guts";
+			reg = <0xe0000 0x1000>;
+			fsl,has-rstcr;
+		};
+
+		par_io@e0100 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <0xe0100 0x60>;
+			ranges = <0x0 0xe0100 0x60>;
+			device_type = "par_io";
+			num-ports = <3>;
+			pio1: ucc_pin@01 {
+				pio-map = <
+			/* port  pin  dir  open_drain  assignment  has_irq */
+					0x1  0x13 0x1  0x0  0x1  0x0    /* QE_MUX_MDC */
+					0x1  0x14 0x3  0x0  0x1  0x0    /* QE_MUX_MDIO */
+					0x0  0x17 0x2  0x0  0x2  0x0    /* CLK12 */
+					0x0  0x18 0x2  0x0  0x1  0x0    /* CLK9
+*/
+					0x0  0x7  0x1  0x0  0x2  0x0    /* ENET1_TXD0_SER1_TXD0 */
+					0x0  0x9  0x1  0x0  0x2  0x0    /* ENET1_TXD1_SER1_TXD1 */
+					0x0  0xb  0x1  0x0  0x2  0x0    /* ENET1_TXD2_SER1_TXD2 */
+					0x0  0xc  0x1  0x0  0x2  0x0    /* ENET1_TXD3_SER1_TXD3 */
+					0x0  0x6  0x2  0x0  0x2  0x0    /* ENET1_RXD0_SER1_RXD0 */
+					0x0  0xa  0x2  0x0  0x2  0x0    /* ENET1_RXD1_SER1_RXD1 */
+					0x0  0xe  0x2  0x0  0x2  0x0    /* ENET1_RXD2_SER1_RXD2 */
+					0x0  0xf  0x2  0x0  0x2  0x0    /* ENET1_RXD3_SER1_RXD3 */
+					0x0  0x5  0x1  0x0  0x2  0x0    /* ENET1_TX_EN_SER1_RTS_B */
+					0x0  0xd  0x1  0x0  0x2  0x0    /* ENET1_TX_ER */
+					0x0  0x4  0x2  0x0  0x2  0x0    /* ENET1_RX_DV_SER1_CTS_B */
+					0x0  0x8  0x2  0x0  0x2  0x0    /* ENET1_RX_ER_SER1_CD_B */
+					0x0  0x11 0x2  0x0  0x2  0x0    /* ENET1_CRS */
+					0x0  0x10 0x2  0x0  0x2  0x0>;    /* ENET1_COL */
+			};
+
+			pio2: ucc_pin@02 {
+				pio-map = <
+			/* port  pin  dir  open_drain  assignment  has_irq */
+					0x1  0x13 0x1  0x0  0x1  0x0    /* QE_MUX_MDC */
+					0x1  0x14 0x3  0x0  0x1  0x0    /* QE_MUX_MDIO */
+					0x1  0xb  0x2  0x0  0x1  0x0    /* CLK13 */
+					0x1  0x7  0x1  0x0  0x2  0x0    /* ENET5_TXD0_SER5_TXD0 */
+					0x1  0xa  0x1  0x0  0x2  0x0    /* ENET5_TXD1_SER5_TXD1 */
+					0x1  0x6  0x2  0x0  0x2  0x0    /* ENET5_RXD0_SER5_RXD0 */
+					0x1  0x9  0x2  0x0  0x2  0x0    /* ENET5_RXD1_SER5_RXD1 */
+					0x1  0x5  0x1  0x0  0x2  0x0    /* ENET5_TX_EN_SER5_RTS_B */
+					0x1  0x4  0x2  0x0  0x2  0x0    /* ENET5_RX_DV_SER5_CTS_B */
+					0x1  0x8  0x2  0x0  0x2  0x0>;    /* ENET5_RX_ER_SER5_CD_B */
+			};
+		};
+	};
+
+	pci0: pcie@ffe09000 {
+		compatible = "fsl,mpc8548-pcie";
+		device_type = "pci";
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		reg = <0 0xffe09000 0 0x1000>;
+		bus-range = <0 255>;
+		ranges = <0x2000000 0x0 0xa0000000 0 0xa0000000 0x0 0x20000000
+			  0x1000000 0x0 0x00000000 0 0xffc10000 0x0 0x10000>;
+		clock-frequency = <33333333>;
+		interrupt-parent = <&mpic>;
+		interrupts = <16 2>;
+		interrupt-map-mask = <0xf800 0 0 7>;
+		interrupt-map = <
+			/* IDSEL 0x0 */
+			0000 0 0 1 &mpic 4 1
+			0000 0 0 2 &mpic 5 1
+			0000 0 0 3 &mpic 6 1
+			0000 0 0 4 &mpic 7 1
+			>;
+		pcie@0 {
+			reg = <0x0 0x0 0x0 0x0 0x0>;
+			#size-cells = <2>;
+			#address-cells = <3>;
+			device_type = "pci";
+			ranges = <0x2000000 0x0 0xa0000000
+				  0x2000000 0x0 0xa0000000
+				  0x0 0x20000000
+
+				  0x1000000 0x0 0x0
+				  0x1000000 0x0 0x0
+				  0x0 0x100000>;
+		};
+	};
+
+	pci1: pcie@ffe0a000 {
+		compatible = "fsl,mpc8548-pcie";
+		device_type = "pci";
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		reg = <0 0xffe0a000 0 0x1000>;
+		bus-range = <0 255>;
+		ranges = <0x2000000 0x0 0xc0000000 0 0xc0000000 0x0 0x20000000
+			  0x1000000 0x0 0x00000000 0 0xffc20000 0x0 0x10000>;
+		clock-frequency = <33333333>;
+		interrupt-parent = <&mpic>;
+		interrupts = <16 2>;
+		interrupt-map-mask = <0xf800 0 0 7>;
+		interrupt-map = <
+			/* IDSEL 0x0 */
+			0000 0 0 1 &mpic 0 1
+			0000 0 0 2 &mpic 1 1
+			0000 0 0 3 &mpic 2 1
+			0000 0 0 4 &mpic 3 1
+			>;
+		pcie@0 {
+			reg = <0x0 0x0 0x0 0x0 0x0>;
+			#size-cells = <2>;
+			#address-cells = <3>;
+			device_type = "pci";
+			ranges = <0x2000000 0x0 0xc0000000
+				  0x2000000 0x0 0xc0000000
+				  0x0 0x20000000
+
+				  0x1000000 0x0 0x0
+				  0x1000000 0x0 0x0
+				  0x0 0x100000>;
+		};
+	};
+
+	qe@ffe80000 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		device_type = "qe";
+		compatible = "fsl,qe";
+		ranges = <0x0 0x0 0xffe80000 0x40000>;
+		reg = <0 0xffe80000 0 0x480>;
+		brg-frequency = <0>;
+		bus-frequency = <0>;
+		fsl,qe-num-riscs = <1>;
+		fsl,qe-num-snums = <28>;
+
+		qeic: interrupt-controller@80 {
+			interrupt-controller;
+			compatible = "fsl,qe-ic";
+			#address-cells = <0>;
+			#interrupt-cells = <1>;
+			reg = <0x80 0x80>;
+			interrupts = <63 2 60 2>; //high:47 low:44
+			interrupt-parent = <&mpic>;
+		};
+
+		enet3: ucc@2000 {
+			device_type = "network";
+			compatible = "ucc_geth";
+			cell-index = <1>;
+			reg = <0x2000 0x200>;
+			interrupts = <32>;
+			interrupt-parent = <&qeic>;
+			local-mac-address = [ 00 00 00 00 00 00 ];
+			rx-clock-name = "clk12";
+			tx-clock-name = "clk9";
+			pio-handle = <&pio1>;
+			phy-handle = <&qe_phy0>;
+			phy-connection-type = "mii";
+		};
+
+		mdio@2120 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x2120 0x18>;
+			compatible = "fsl,ucc-mdio";
+
+			qe_phy0: ethernet-phy@0 {
+				interrupt-parent = <&mpic>;
+				interrupts = <4 1>;
+				reg = <0x0>;
+				device_type = "ethernet-phy";
+			};
+			qe_phy1: ethernet-phy@03 {
+				interrupt-parent = <&mpic>;
+				interrupts = <5 1>;
+				reg = <0x3>;
+				device_type = "ethernet-phy";
+			};
+			tbi-phy@11 {
+				reg = <0x11>;
+				device_type = "tbi-phy";
+			};
+		};
+
+		enet4: ucc@2400 {
+			device_type = "network";
+			compatible = "ucc_geth";
+			cell-index = <5>;
+			reg = <0x2400 0x200>;
+			interrupts = <40>;
+			interrupt-parent = <&qeic>;
+			local-mac-address = [ 00 00 00 00 00 00 ];
+			rx-clock-name = "none";
+			tx-clock-name = "clk13";
+			pio-handle = <&pio2>;
+			phy-handle = <&qe_phy1>;
+			phy-connection-type = "rmii";
+		};
+
+		muram@10000 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "fsl,qe-muram", "fsl,cpm-muram";
+			ranges = <0x0 0x10000 0x6000>;
+
+			data-only@0 {
+				compatible = "fsl,qe-muram-data",
+				"fsl,cpm-muram-data";
+				reg = <0x0 0x6000>;
+			};
+		};
+	};
+};
arch/powerpc/platforms/85xx/mpc85xx_mds.c +96 -3

156 lines not on this page · raw message

Signature · 1 line
1.6.0.2
#4 lore raw

Re: [PATCH] powerpc/85xx: Add P1021MDS board support

Quoted 8 lines
arch/powerpc/platforms/85xx/mpc85xx_mds.c +7 -0
+
+	if (machine_is(p1021_mds)) {
+#define MPC85xx_PMUXCR_OFFSET           0x60
+#define MPC85xx_PMUXCR_QE0              0x00008000
+#define MPC85xx_PMUXCR_QE3              0x00001000
+#define MPC85xx_PMUXCR_QE9              0x00000040
+#define MPC85xx_PMUXCR_QE12             0x00000008

arch/powerpc/platforms/85xx/mpc85xx_mds.c static void __init mpc85xx_mds_setup_arch(void) · line 307

Quoted 10 lines
arch/powerpc/platforms/85xx/mpc85xx_mds.c +10 -0
+		static __be32 __iomem *pmuxcr;
+
+		np = of_find_node_by_name(NULL, "global-utilities");
+
+		if (np) {
+			pmuxcr = of_iomap(np, 0) + MPC85xx_PMUXCR_OFFSET;
+			if (!pmuxcr)
+				printk(KERN_EMERG "Error: Alternate function"
+					" signal multiplex control register not"
+					" mapped!\n");

if we error shouldn't we not do the setbit32?

Quoted 110 lines
arch/powerpc/platforms/85xx/mpc85xx_mds.c +14 -0
+
+			/* P1021 has pins muxed for QE and other functions. To
+			 * enable QE UEC mode, we need to set bit QE0 for UCC1
+			 * in Eth mode, QE0 and QE3 for UCC5 in Eth mode, QE9
+			 * and QE12 for QE MII management singals in PMUXCR
+			 * register.
+			 */
+			setbits32(pmuxcr,
+				MPC85xx_PMUXCR_QE0 | MPC85xx_PMUXCR_QE3 |
+				MPC85xx_PMUXCR_QE9 | MPC85xx_PMUXCR_QE12);
+		}
+
+		of_node_put(np);
+	}

#endif /* CONFIG_QUICC_ENGINE */

#ifdef CONFIG_SWIOTLB

arch/powerpc/platforms/85xx/mpc85xx_mds.c +50 -2
@@ -330,6 +375,16 @@ static struct of_device_id mpc85xx_ids[] = {
 	{},
 };
 
+static struct of_device_id p1021_ids[] = {
+	{ .type = "soc", },
+	{ .compatible = "soc", },
+	{ .compatible = "simple-bus", },
+	{ .type = "qe", },
+	{ .compatible = "fsl,qe", },
+	{ .compatible = "gianfar", },
+	{},
+};
+
 static int __init mpc85xx_publish_devices(void)
 {
 	if (machine_is(mpc8568_mds))

@@ -342,11 +397,22 @@ static int __init mpc85xx_publish_devices(void)
 
 	return 0;
 }
+
+static int __init p1021_publish_devices(void)
+{
+	/* Publish the QE devices */
+	of_platform_bus_probe(NULL, p1021_ids, NULL);
+
+	return 0;
+}
+
 machine_device_initcall(mpc8568_mds, mpc85xx_publish_devices);
 machine_device_initcall(mpc8569_mds, mpc85xx_publish_devices);
+machine_device_initcall(p1021_mds, p1021_publish_devices);
 
 machine_arch_initcall(mpc8568_mds, swiotlb_setup_bus_notifier);
 machine_arch_initcall(mpc8569_mds, swiotlb_setup_bus_notifier);
+machine_arch_initcall(p1021_mds, swiotlb_setup_bus_notifier);
 
 static void __init mpc85xx_mds_pic_init(void)
 {

@@ -366,7 +432,7 @@ static void __init mpc85xx_mds_pic_init(void)
 
 	mpic = mpic_alloc(np, r.start,
 			MPIC_PRIMARY | MPIC_WANTS_RESET | MPIC_BIG_ENDIAN |
-			MPIC_BROKEN_FRR_NIRQS,
+			MPIC_BROKEN_FRR_NIRQS | MPIC_SINGLE_DEST_CPU,
 			0, 256, " OpenPIC  ");
 	BUG_ON(mpic == NULL);
 	of_node_put(np);

@@ -380,7 +446,11 @@ static void __init mpc85xx_mds_pic_init(void)
 		if (!np)
 			return;
 	}
-	qe_ic_init(np, 0, qe_ic_cascade_muxed_mpic, NULL);
+	if (machine_is(p1021_mds))
+		qe_ic_init(np, 0, qe_ic_cascade_low_mpic,
+				qe_ic_cascade_high_mpic);
+	else
+		qe_ic_init(np, 0, qe_ic_cascade_muxed_mpic, NULL);
 	of_node_put(np);
 #endif				/* CONFIG_QUICC_ENGINE */
 }

@@ -426,3 +496,26 @@ define_machine(mpc8569_mds) {
 	.pcibios_fixup_bus	= fsl_pcibios_fixup_bus,
 #endif
 };
+
+static int __init p1021_mds_probe(void)
+{
+	unsigned long root = of_get_flat_dt_root();
+
+	return of_flat_dt_is_compatible(root, "fsl,P1021MDS");
+
+}
+
+define_machine(p1021_mds) {
+	.name		= "P1021 MDS",
+	.probe		= p1021_mds_probe,
+	.setup_arch	= mpc85xx_mds_setup_arch,
+	.init_IRQ	= mpc85xx_mds_pic_init,
+	.get_irq	= mpic_get_irq,
+	.restart	= fsl_rstcr_restart,
+	.calibrate_decr	= generic_calibrate_decr,
+	.progress	= udbg_progress,
+#ifdef CONFIG_PCI
+	.pcibios_fixup_bus	= fsl_pcibios_fixup_bus,
+#endif
+};
+
Signature · 1 line
1.6.0.2
#5 lore raw

PATCH v2 1/1 powerpc/85xx: Add P1021MDS board support

In reply to Haiying Wang

P1021 is a dual e500v2 core based SOC with:
* 3 eTSECs (eTSEC1/3 RGMII, eTSEC2 SGMII on this board)
* 2 PCIe Controller
* 1 USB2.0 controller
* eSDHC, eSPI, I2C, DUART
* eLBC (NAND, BCSR, PMC0/1)
* Security Engine (SEC 3.3.2)
* Quicc Engine (QE)

Signed-off-by Haiying Wang <[email protected]>
Signed-off-by Yu Liu <[email protected]>

---
v2: address the comments from Kumar.

 arch/powerpc/boot/dts/p1021mds.dts        |  698 +++++++++++++++++++++++++++++
 arch/powerpc/platforms/85xx/mpc85xx_mds.c |  102 ++++-
 2 files changed, 797 insertions(+), 3 deletions(-)
 create mode 100644 arch/powerpc/boot/dts/p1021mds.dts
arch/powerpc/boot/dts/p1021mds.dts new file +698 -0
new file mode 100644
index 0000000..7fad2df
@@ -0,0 +1,698 @@
+/*
+ * P1021 MDS Device Tree Source
+ *
+ * Copyright 2010 Freescale Semiconductor Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+/dts-v1/;
+/ {
+	model = "fsl,P1021";
+	compatible = "fsl,P1021MDS";
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	aliases {
+		serial0 = &serial0;
+		serial1 = &serial1;
+		ethernet0 = &enet0;
+		ethernet1 = &enet1;
+		ethernet2 = &enet2;
+		ethernet3 = &enet3;
+		ethernet4 = &enet4;
+		pci0 = &pci0;
+		pci1 = &pci1;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		PowerPC,P1021@0 {
+			device_type = "cpu";
+			reg = <0x0>;
+			next-level-cache = <&L2>;
+		};
+
+		PowerPC,P1021@1 {
+			device_type = "cpu";
+			reg = <0x1>;
+			next-level-cache = <&L2>;
+		};
+	};
+
+	memory {
+		device_type = "memory";
+	};
+
+	localbus@ffe05000 {
+		#address-cells = <2>;
+		#size-cells = <1>;
+		compatible = "fsl,p1021-elbc", "fsl,elbc", "simple-bus";
+		reg = <0 0xffe05000 0 0x1000>;
+		interrupts = <19 2>;
+		interrupt-parent = <&mpic>;
+
+		/* NAND Flash, BCSR, PMC0/1*/
+		ranges = <0x0 0x0 0x0 0xfc000000 0x02000000
+			  0x1 0x0 0x0 0xf8000000 0x00008000
+			  0x2 0x0 0x0 0xf8010000 0x00020000
+			  0x3 0x0 0x0 0xf8020000 0x00020000>;
+
+		nand@0,0 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "fsl,p1021-fcm-nand",
+				     "fsl,elbc-fcm-nand";
+			reg = <0x0 0x0 0x40000>;
+
+			partition@0 {
+				/* This location must not be altered  */
+				/* 1MB for u-boot Bootloader Image */
+				reg = <0x0 0x00100000>;
+				label = "NAND (RO) U-Boot Image";
+				read-only;
+			};
+
+			partition@100000 {
+				/* 1MB for DTB Image */
+				reg = <0x00100000 0x00100000>;
+				label = "NAND (RO) DTB Image";
+				read-only;
+			};
+
+			partition@200000 {
+				/* 4MB for Linux Kernel Image */
+				reg = <0x00200000 0x00400000>;
+				label = "NAND (RO) Linux Kernel Image";
+				read-only;
+			};
+
+			partition@600000 {
+				/* 5MB for Compressed Root file System Image */
+				reg = <0x00600000 0x00500000>;
+				label = "NAND (RO) Compressed RFS Image";
+				read-only;
+			};
+
+			partition@b00000 {
+				/* 6MB for JFFS2 based Root file System */
+				reg = <0x00a00000 0x00600000>;
+				label = "NAND (RW) JFFS2 Root File System";
+			};
+
+			partition@1100000 {
+				/* 14MB for JFFS2 based Root file System */
+				reg = <0x01100000 0x00e00000>;
+				label = "NAND (RW) Writable User area";
+			};
+
+			partition@1f00000 {
+				/* 1MB for microcode */
+				reg = <0x01f00000 0x00100000>;
+				label = "NAND (RO) QE Ucode";
+				read-only;
+			};
+		};
+
+		bcsr@1,0 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "fsl,p1021mds-bcsr";
+			reg = <1 0 0x8000>;
+			ranges = <0 1 0 0x8000>;
+		};
+
+		pib@2,0 {
+			compatible = "fsl,p1021mds-pib";
+			reg = <2 0 0x10000>;
+		};
+
+		pib@3,0 {
+			compatible = "fsl,p1021mds-pib";
+			reg = <3 0 0x10000>;
+		};
+	};
+
+	soc@ffe00000 {
+
+		#address-cells = <1>;
+		#size-cells = <1>;
+		device_type = "soc";
+		compatible = "fsl,p1021-immr", "simple-bus";
+		ranges = <0x0  0x0 0xffe00000 0x100000>;
+		bus-frequency = <0>;		// Filled out by uboot.
+
+		ecm-law@0 {
+			compatible = "fsl,ecm-law";
+			reg = <0x0 0x1000>;
+			fsl,num-laws = <12>;
+		};
+
+		ecm@1000 {
+			compatible = "fsl,p1021-ecm", "fsl,ecm";
+			reg = <0x1000 0x1000>;
+			interrupts = <16 2>;
+			interrupt-parent = <&mpic>;
+		};
+
+		memory-controller@2000 {
+			compatible = "fsl,p1021-memory-controller";
+			reg = <0x2000 0x1000>;
+			interrupt-parent = <&mpic>;
+			interrupts = <16 2>;
+		};
+
+		i2c@3000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			cell-index = <0>;
+			compatible = "fsl-i2c";
+			reg = <0x3000 0x100>;
+			interrupts = <43 2>;
+			interrupt-parent = <&mpic>;
+			dfsrr;
+			rtc@68 {
+				compatible = "dallas,ds1374";
+				reg = <0x68>;
+			};
+		};
+
+		i2c@3100 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			cell-index = <1>;
+			compatible = "fsl-i2c";
+			reg = <0x3100 0x100>;
+			interrupts = <43 2>;
+			interrupt-parent = <&mpic>;
+			dfsrr;
+		};
+
+		serial0: serial@4500 {
+			cell-index = <0>;
+			device_type = "serial";
+			compatible = "ns16550";
+			reg = <0x4500 0x100>;
+			clock-frequency = <0>;
+			interrupts = <42 2>;
+			interrupt-parent = <&mpic>;
+		};
+
+		serial1: serial@4600 {
+			cell-index = <1>;
+			device_type = "serial";
+			compatible = "ns16550";
+			reg = <0x4600 0x100>;
+			clock-frequency = <0>;
+			interrupts = <42 2>;
+			interrupt-parent = <&mpic>;
+		};
+
+		spi@7000 {
+			cell-index = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "fsl,espi";
+			reg = <0x7000 0x1000>;
+			interrupts = <59 0x2>;
+			interrupt-parent = <&mpic>;
+			espi,num-ss-bits = <4>;
+			mode = "cpu";
+
+			fsl_m25p80@0 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				compatible = "fsl,espi-flash";
+				reg = <0>;
+				linux,modalias = "fsl_m25p80";
+				spi-max-frequency = <40000000>; /* input clock */
+				partition@u-boot {
+					label = "u-boot-spi";
+					reg = <0x00000000 0x00100000>;
+					read-only;
+				};
+				partition@kernel {
+					label = "kernel-spi";
+					reg = <0x00100000 0x00500000>;
+					read-only;
+				};
+				partition@dtb {
+					label = "dtb-spi";
+					reg = <0x00600000 0x00100000>;
+					read-only;
+				};
+				partition@fs {
+					label = "file system-spi";
+					reg = <0x00700000 0x00900000>;
+				};
+			};
+		};
+
+		gpio: gpio-controller@f000 {
+			#gpio-cells = <2>;
+			compatible = "fsl,mpc8572-gpio";
+			reg = <0xf000 0x100>;
+			interrupts = <47 0x2>;
+			interrupt-parent = <&mpic>;
+			gpio-controller;
+		};
+
+		L2: l2-cache-controller@20000 {
+			compatible = "fsl,p1021-l2-cache-controller";
+			reg = <0x20000 0x1000>;
+			cache-line-size = <32>;	// 32 bytes
+			cache-size = <0x40000>; // L2,256K
+			interrupt-parent = <&mpic>;
+			interrupts = <16 2>;
+		};
+
+		dma@21300 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "fsl,eloplus-dma";
+			reg = <0x21300 0x4>;
+			ranges = <0x0 0x21100 0x200>;
+			cell-index = <0>;
+			dma-channel@0 {
+				compatible = "fsl,eloplus-dma-channel";
+				reg = <0x0 0x80>;
+				cell-index = <0>;
+				interrupt-parent = <&mpic>;
+				interrupts = <20 2>;
+			};
+			dma-channel@80 {
+				compatible = "fsl,eloplus-dma-channel";
+				reg = <0x80 0x80>;
+				cell-index = <1>;
+				interrupt-parent = <&mpic>;
+				interrupts = <21 2>;
+			};
+			dma-channel@100 {
+				compatible = "fsl,eloplus-dma-channel";
+				reg = <0x100 0x80>;
+				cell-index = <2>;
+				interrupt-parent = <&mpic>;
+				interrupts = <22 2>;
+			};
+			dma-channel@180 {
+				compatible = "fsl,eloplus-dma-channel";
+				reg = <0x180 0x80>;
+				cell-index = <3>;
+				interrupt-parent = <&mpic>;
+				interrupts = <23 2>;
+			};
+		};
+
+		usb@22000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "fsl-usb2-dr";
+			reg = <0x22000 0x1000>;
+			interrupt-parent = <&mpic>;
+			interrupts = <28 0x2>;
+			phy_type = "ulpi";
+		};
+
+		 mdio@24000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "fsl,etsec2-mdio";
+			reg = <0x24000 0x1000 0xb0030 0x4>;
+
+			phy0: ethernet-phy@0 {
+				interrupt-parent = <&mpic>;
+				interrupts = <1 1>;
+				reg = <0x0>;
+			};
+			phy1: ethernet-phy@1 {
+				interrupt-parent = <&mpic>;
+				interrupts = <2 1>;
+				reg = <0x1>;
+			};
+			phy4: ethernet-phy@4 {
+				interrupt-parent = <&mpic>;
+				reg = <0x4>;
+			};
+		};
+
+		mdio@25000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "fsl,etsec2-tbi";
+			reg = <0x25000 0x1000 0xb1030 0x4>;
+			tbi0: tbi-phy@11 {
+				reg = <0x11>;
+				device_type = "tbi-phy";
+			};
+		};
+
+		enet0: ethernet@B0000 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			cell-index = <0>;
+			device_type = "network";
+			model = "eTSEC";
+			compatible = "fsl,etsec2";
+			fsl,num_rx_queues = <0x8>;
+			fsl,num_tx_queues = <0x8>;
+			local-mac-address = [ 00 00 00 00 00 00 ];
+			interrupt-parent = <&mpic>;
+			phy-handle = <&phy0>;
+			phy-connection-type = "rgmii-id";
+			queue-group@0{
+				#address-cells = <1>;
+				#size-cells = <1>;
+				reg = <0xB0000 0x1000>;
+				interrupts = <29 2 30 2 34 2>;
+			};
+			queue-group@1{
+				#address-cells = <1>;
+				#size-cells = <1>;
+				reg = <0xB4000 0x1000>;
+				interrupts = <17 2 18 2 24 2>;
+			};
+		};
+
+		enet1: ethernet@B1000 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			cell-index = <0>;
+			device_type = "network";
+			model = "eTSEC";
+			compatible = "fsl,etsec2";
+			fsl,num_rx_queues = <0x8>;
+			fsl,num_tx_queues = <0x8>;
+			local-mac-address = [ 00 00 00 00 00 00 ];
+			interrupt-parent = <&mpic>;
+			phy-handle = <&phy4>;
+			tbi-handle = <&tbi0>;
+			phy-connection-type = "sgmii";
+			queue-group@0{
+				#address-cells = <1>;
+				#size-cells = <1>;
+				reg = <0xB1000 0x1000>;
+				interrupts = <35 2 36 2 40 2>;
+			};
+			queue-group@1{
+				#address-cells = <1>;
+				#size-cells = <1>;
+				reg = <0xB5000 0x1000>;
+				interrupts = <51 2 52 2 67 2>;
+			};
+		};
+
+		enet2: ethernet@B2000 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			cell-index = <0>;
+			device_type = "network";
+			model = "eTSEC";
+			compatible = "fsl,etsec2";
+			fsl,num_rx_queues = <0x8>;
+			fsl,num_tx_queues = <0x8>;
+			local-mac-address = [ 00 00 00 00 00 00 ];
+			interrupt-parent = <&mpic>;
+			phy-handle = <&phy1>;
+			phy-connection-type = "rgmii-id";
+			queue-group@0{
+				#address-cells = <1>;
+				#size-cells = <1>;
+				reg = <0xB2000 0x1000>;
+				interrupts = <31 2 32 2 33 2>;
+			};
+			queue-group@1{
+				#address-cells = <1>;
+				#size-cells = <1>;
+				reg = <0xB6000 0x1000>;
+				interrupts = <25 2 26 2 27 2>;
+			};
+		};
+
+		sdhci@2e000 {
+			compatible = "fsl,p1021-esdhc", "fsl,esdhc";
+			reg = <0x2e000 0x1000>;
+			interrupts = <72 0x2>;
+			interrupt-parent = <&mpic>;
+			/* Filled in by U-Boot */
+			clock-frequency = <0>;
+		};
+
+		crypto@30000 {
+			compatible = "fsl,sec3.3", "fsl,sec3.1",
+				     "fsl,sec3.0", "fsl,sec2.4",
+				     "fsl,sec2.2", "fsl,sec2.1", "fsl,sec2.0";
+			reg = <0x30000 0x10000>;
+			interrupts = <45 2 58 2>;
+			interrupt-parent = <&mpic>;
+			fsl,num-channels = <4>;
+			fsl,channel-fifo-len = <24>;
+			fsl,exec-units-mask = <0x97c>;
+			fsl,descriptor-types-mask = <0x3a30abf>;
+		};
+
+		mpic: pic@40000 {
+			interrupt-controller;
+			#address-cells = <0>;
+			#interrupt-cells = <2>;
+			reg = <0x40000 0x40000>;
+			compatible = "chrp,open-pic";
+			device_type = "open-pic";
+		};
+
+		msi@41600 {
+			compatible = "fsl,p1021-msi", "fsl,mpic-msi";
+			reg = <0x41600 0x80>;
+			msi-available-ranges = <0 0x100>;
+			interrupts = <
+				0xe0 0
+				0xe1 0
+				0xe2 0
+				0xe3 0
+				0xe4 0
+				0xe5 0
+				0xe6 0
+				0xe7 0>;
+			interrupt-parent = <&mpic>;
+		};
+
+		global-utilities@e0000 {	//global utilities block
+			compatible = "fsl,p1021-guts";
+			reg = <0xe0000 0x1000>;
+			fsl,has-rstcr;
+		};
+
+		par_io@e0100 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <0xe0100 0x60>;
+			ranges = <0x0 0xe0100 0x60>;
+			device_type = "par_io";
+			num-ports = <3>;
+			pio1: ucc_pin@01 {
+				pio-map = <
+			/* port  pin  dir  open_drain  assignment  has_irq */
+					0x1  0x13 0x1  0x0  0x1  0x0    /* QE_MUX_MDC */
+					0x1  0x14 0x3  0x0  0x1  0x0    /* QE_MUX_MDIO */
+					0x0  0x17 0x2  0x0  0x2  0x0    /* CLK12 */
+					0x0  0x18 0x2  0x0  0x1  0x0    /* CLK9
+*/
+					0x0  0x7  0x1  0x0  0x2  0x0    /* ENET1_TXD0_SER1_TXD0 */
+					0x0  0x9  0x1  0x0  0x2  0x0    /* ENET1_TXD1_SER1_TXD1 */
+					0x0  0xb  0x1  0x0  0x2  0x0    /* ENET1_TXD2_SER1_TXD2 */
+					0x0  0xc  0x1  0x0  0x2  0x0    /* ENET1_TXD3_SER1_TXD3 */
+					0x0  0x6  0x2  0x0  0x2  0x0    /* ENET1_RXD0_SER1_RXD0 */
+					0x0  0xa  0x2  0x0  0x2  0x0    /* ENET1_RXD1_SER1_RXD1 */
+					0x0  0xe  0x2  0x0  0x2  0x0    /* ENET1_RXD2_SER1_RXD2 */
+					0x0  0xf  0x2  0x0  0x2  0x0    /* ENET1_RXD3_SER1_RXD3 */
+					0x0  0x5  0x1  0x0  0x2  0x0    /* ENET1_TX_EN_SER1_RTS_B */
+					0x0  0xd  0x1  0x0  0x2  0x0    /* ENET1_TX_ER */
+					0x0  0x4  0x2  0x0  0x2  0x0    /* ENET1_RX_DV_SER1_CTS_B */
+					0x0  0x8  0x2  0x0  0x2  0x0    /* ENET1_RX_ER_SER1_CD_B */
+					0x0  0x11 0x2  0x0  0x2  0x0    /* ENET1_CRS */
+					0x0  0x10 0x2  0x0  0x2  0x0>;    /* ENET1_COL */
+			};
+
+			pio2: ucc_pin@02 {
+				pio-map = <
+			/* port  pin  dir  open_drain  assignment  has_irq */
+					0x1  0x13 0x1  0x0  0x1  0x0    /* QE_MUX_MDC */
+					0x1  0x14 0x3  0x0  0x1  0x0    /* QE_MUX_MDIO */
+					0x1  0xb  0x2  0x0  0x1  0x0    /* CLK13 */
+					0x1  0x7  0x1  0x0  0x2  0x0    /* ENET5_TXD0_SER5_TXD0 */
+					0x1  0xa  0x1  0x0  0x2  0x0    /* ENET5_TXD1_SER5_TXD1 */
+					0x1  0x6  0x2  0x0  0x2  0x0    /* ENET5_RXD0_SER5_RXD0 */
+					0x1  0x9  0x2  0x0  0x2  0x0    /* ENET5_RXD1_SER5_RXD1 */
+					0x1  0x5  0x1  0x0  0x2  0x0    /* ENET5_TX_EN_SER5_RTS_B */
+					0x1  0x4  0x2  0x0  0x2  0x0    /* ENET5_RX_DV_SER5_CTS_B */
+					0x1  0x8  0x2  0x0  0x2  0x0>;    /* ENET5_RX_ER_SER5_CD_B */
+			};
+		};
+	};
+
+	pci0: pcie@ffe09000 {
+		compatible = "fsl,mpc8548-pcie";
+		device_type = "pci";
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		reg = <0 0xffe09000 0 0x1000>;
+		bus-range = <0 255>;
+		ranges = <0x2000000 0x0 0xa0000000 0 0xa0000000 0x0 0x20000000
+			  0x1000000 0x0 0x00000000 0 0xffc10000 0x0 0x10000>;
+		clock-frequency = <33333333>;
+		interrupt-parent = <&mpic>;
+		interrupts = <16 2>;
+		interrupt-map-mask = <0xf800 0 0 7>;
+		interrupt-map = <
+			/* IDSEL 0x0 */
+			0000 0 0 1 &mpic 4 1
+			0000 0 0 2 &mpic 5 1
+			0000 0 0 3 &mpic 6 1
+			0000 0 0 4 &mpic 7 1
+			>;
+		pcie@0 {
+			reg = <0x0 0x0 0x0 0x0 0x0>;
+			#size-cells = <2>;
+			#address-cells = <3>;
+			device_type = "pci";
+			ranges = <0x2000000 0x0 0xa0000000
+				  0x2000000 0x0 0xa0000000
+				  0x0 0x20000000
+
+				  0x1000000 0x0 0x0
+				  0x1000000 0x0 0x0
+				  0x0 0x100000>;
+		};
+	};
+
+	pci1: pcie@ffe0a000 {
+		compatible = "fsl,mpc8548-pcie";
+		device_type = "pci";
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		reg = <0 0xffe0a000 0 0x1000>;
+		bus-range = <0 255>;
+		ranges = <0x2000000 0x0 0xc0000000 0 0xc0000000 0x0 0x20000000
+			  0x1000000 0x0 0x00000000 0 0xffc20000 0x0 0x10000>;
+		clock-frequency = <33333333>;
+		interrupt-parent = <&mpic>;
+		interrupts = <16 2>;
+		interrupt-map-mask = <0xf800 0 0 7>;
+		interrupt-map = <
+			/* IDSEL 0x0 */
+			0000 0 0 1 &mpic 0 1
+			0000 0 0 2 &mpic 1 1
+			0000 0 0 3 &mpic 2 1
+			0000 0 0 4 &mpic 3 1
+			>;
+		pcie@0 {
+			reg = <0x0 0x0 0x0 0x0 0x0>;
+			#size-cells = <2>;
+			#address-cells = <3>;
+			device_type = "pci";
+			ranges = <0x2000000 0x0 0xc0000000
+				  0x2000000 0x0 0xc0000000
+				  0x0 0x20000000
+
+				  0x1000000 0x0 0x0
+				  0x1000000 0x0 0x0
+				  0x0 0x100000>;
+		};
+	};
+
+	qe@ffe80000 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		device_type = "qe";
+		compatible = "fsl,qe";
+		ranges = <0x0 0x0 0xffe80000 0x40000>;
+		reg = <0 0xffe80000 0 0x480>;
+		brg-frequency = <0>;
+		bus-frequency = <0>;
+		fsl,qe-num-riscs = <1>;
+		fsl,qe-num-snums = <28>;
+
+		qeic: interrupt-controller@80 {
+			interrupt-controller;
+			compatible = "fsl,qe-ic";
+			#address-cells = <0>;
+			#interrupt-cells = <1>;
+			reg = <0x80 0x80>;
+			interrupts = <63 2 60 2>; //high:47 low:44
+			interrupt-parent = <&mpic>;
+		};
+
+		enet3: ucc@2000 {
+			device_type = "network";
+			compatible = "ucc_geth";
+			cell-index = <1>;
+			reg = <0x2000 0x200>;
+			interrupts = <32>;
+			interrupt-parent = <&qeic>;
+			local-mac-address = [ 00 00 00 00 00 00 ];
+			rx-clock-name = "clk12";
+			tx-clock-name = "clk9";
+			pio-handle = <&pio1>;
+			phy-handle = <&qe_phy0>;
+			phy-connection-type = "mii";
+		};
+
+		mdio@2120 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x2120 0x18>;
+			compatible = "fsl,ucc-mdio";
+
+			qe_phy0: ethernet-phy@0 {
+				interrupt-parent = <&mpic>;
+				interrupts = <4 1>;
+				reg = <0x0>;
+				device_type = "ethernet-phy";
+			};
+			qe_phy1: ethernet-phy@03 {
+				interrupt-parent = <&mpic>;
+				interrupts = <5 1>;
+				reg = <0x3>;
+				device_type = "ethernet-phy";
+			};
+			tbi-phy@11 {
+				reg = <0x11>;
+				device_type = "tbi-phy";
+			};
+		};
+
+		enet4: ucc@2400 {
+			device_type = "network";
+			compatible = "ucc_geth";
+			cell-index = <5>;
+			reg = <0x2400 0x200>;
+			interrupts = <40>;
+			interrupt-parent = <&qeic>;
+			local-mac-address = [ 00 00 00 00 00 00 ];
+			rx-clock-name = "none";
+			tx-clock-name = "clk13";
+			pio-handle = <&pio2>;
+			phy-handle = <&qe_phy1>;
+			phy-connection-type = "rmii";
+		};
+
+		muram@10000 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "fsl,qe-muram", "fsl,cpm-muram";
+			ranges = <0x0 0x10000 0x6000>;
+
+			data-only@0 {
+				compatible = "fsl,qe-muram-data",
+				"fsl,cpm-muram-data";
+				reg = <0x0 0x6000>;
+			};
+		};
+	};
+};
arch/powerpc/platforms/85xx/mpc85xx_mds.c +99 -3

159 lines not on this page · raw message

Signature · 1 line
1.6.0.2
Applied
#6 lore raw

Re: [PATCH v2] powerpc/85xx: Add P1021MDS board support

Quoted 9 lines · Haiying Wang

P1021 is a dual e500v2 core based SOC with:
* 3 eTSECs (eTSEC1/3 RGMII, eTSEC2 SGMII on this board)
* 2 PCIe Controller
* 1 USB2.0 controller
* eSDHC, eSPI, I2C, DUART
* eLBC (NAND, BCSR, PMC0/1)
* Security Engine (SEC 3.3.2)
* Quicc Engine (QE)
=20

Quoted 5 lines
Signed-off-by Haiying Wang <[email protected]>
Signed-off-by Yu Liu <[email protected]>

---
v2: address the comments from Kumar.
arch/powerpc/boot/dts/p1021mds.dts | 698 =

+++++++++++++++++++++++++++++

Quoted 3 lines

arch/powerpc/platforms/85xx/mpc85xx_mds.c | 102 ++++-

2 files changed, 797 insertions(+), 3 deletions(-)

create mode 100644 arch/powerpc/boot/dts/p1021mds.dts

applied to next

- k=