Skip to contentSkip to conversation

e1000: Use netdev_<level>, pr_<level> and dev_<level>

PATCH Applied Jeff Kirsher 2 participants 2 messages Apr 28, 2010

Subsystems (2)
Networking Network drivers
lore
Share & tools
lore

Jeff Kirsher

author
#0 lore raw

PATCH 1/1 e1000: Use netdev_<level>, pr_<level> and dev_<level>

From: Emil Tantilov <[email protected]>

This patch is an alternative to similar patch provided by Joe Perches.

Substitute DPRINTK macro for e_<level> that uses netdev_<level> and dev_<level> similar to e1000e.
- Convert printk to pr_<level> where applicable.
- Use common #define pr_fmt for the driver.
- Use dev_<level> for displaying text in parts of the driver where the interface name is not assigned (like e1000_param.c).
- Better align test with the new macros.

CC Joe Perches <[email protected]>
Signed-off-by Emil Tantilov <[email protected]>
Signed-off-by Jeff Kirsher <[email protected]>

---

 drivers/net/e1000/e1000.h         |   37 ++--
 drivers/net/e1000/e1000_ethtool.c |   31 ++-
 drivers/net/e1000/e1000_hw.c      |  356 ++++++++++++++++++-------------------
 drivers/net/e1000/e1000_hw.h      |    1 
 drivers/net/e1000/e1000_main.c    |  239 ++++++++++++-------------
 drivers/net/e1000/e1000_osdep.h   |   14 -
 drivers/net/e1000/e1000_param.c   |   94 ++++------
 7 files changed, 367 insertions(+), 405 deletions(-)
drivers/net/e1000/e1000.h +20 -17
index 2f29c21..40b62b4 100644
@@ -81,23 +81,6 @@ struct e1000_adapter;
 
 #include "e1000_hw.h"
 
-#ifdef DBG
-#define E1000_DBG(args...) printk(KERN_DEBUG "e1000: " args)
-#else
-#define E1000_DBG(args...)
-#endif
-
-#define E1000_ERR(args...) printk(KERN_ERR "e1000: " args)
-
-#define PFX "e1000: "
-
-#define DPRINTK(nlevel, klevel, fmt, args...)				\
-do {									\
-	if (NETIF_MSG_##nlevel & adapter->msg_enable)			\
-		printk(KERN_##klevel PFX "%s: %s: " fmt,		\
-		       adapter->netdev->name, __func__, ##args);	\
-} while (0)
-
 #define E1000_MAX_INTR 10
 
 /* TX/RX descriptor defines */

@@ -335,6 +318,25 @@ enum e1000_state_t {
 	__E1000_DOWN
 };
 
+#undef pr_fmt
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
+extern struct net_device *e1000_get_hw_dev(struct e1000_hw *hw);
+#define e_dbg(format, arg...) \
+	netdev_dbg(e1000_get_hw_dev(hw), format, ## arg)
+#define e_err(format, arg...) \
+	netdev_err(adapter->netdev, format, ## arg)
+#define e_info(format, arg...) \
+	netdev_info(adapter->netdev, format, ## arg)
+#define e_warn(format, arg...) \
+	netdev_warn(adapter->netdev, format, ## arg)
+#define e_notice(format, arg...) \
+	netdev_notice(adapter->netdev, format, ## arg)
+#define e_dev_info(format, arg...) \
+	dev_info(&adapter->pdev->dev, format, ## arg)
+#define e_dev_warn(format, arg...) \
+	dev_warn(&adapter->pdev->dev, format, ## arg)
+
 extern char e1000_driver_name[];
 extern const char e1000_driver_version[];
 

@@ -352,5 +354,6 @@ extern bool e1000_has_link(struct e1000_adapter *adapter);
 extern void e1000_power_up_phy(struct e1000_adapter *);
 extern void e1000_set_ethtool_ops(struct net_device *netdev);
 extern void e1000_check_options(struct e1000_adapter *adapter);
+extern char *e1000_get_hw_dev_name(struct e1000_hw *hw);
 
 #endif /* _E1000_H_ */
drivers/net/e1000/e1000_ethtool.c +15 -16
index 616b405..d6931ca 100644
@@ -346,7 +346,7 @@ static int e1000_set_tso(struct net_device *netdev, u32 data)
 
 	netdev->features &= ~NETIF_F_TSO6;
 
-	DPRINTK(PROBE, INFO, "TSO is %s\n", data ? "Enabled" : "Disabled");
+	e_info("TSO is %s\n", data ? "Enabled" : "Disabled");
 	adapter->tso_force = true;
 	return 0;
 }

@@ -714,9 +714,9 @@ static bool reg_pattern_test(struct e1000_adapter *adapter, u64 *data, int reg,
 		writel(write & test[i], address);
 		read = readl(address);
 		if (read != (write & test[i] & mask)) {
-			DPRINTK(DRV, ERR, "pattern test reg %04X failed: "
-				"got 0x%08X expected 0x%08X\n",
-				reg, read, (write & test[i] & mask));
+			e_info("pattern test reg %04X failed: "
+			       "got 0x%08X expected 0x%08X\n",
+			       reg, read, (write & test[i] & mask));
 			*data = reg;
 			return true;
 		}

@@ -734,9 +734,9 @@ static bool reg_set_and_check(struct e1000_adapter *adapter, u64 *data, int reg,
 	writel(write & mask, address);
 	read = readl(address);
 	if ((read & mask) != (write & mask)) {
-		DPRINTK(DRV, ERR, "set/check reg %04X test failed: "
-			"got 0x%08X expected 0x%08X\n",
-			reg, (read & mask), (write & mask));
+		e_err("set/check reg %04X test failed: "
+		      "got 0x%08X expected 0x%08X\n",
+		      reg, (read & mask), (write & mask));
 		*data = reg;
 		return true;
 	}

@@ -779,8 +779,8 @@ static int e1000_reg_test(struct e1000_adapter *adapter, u64 *data)
 	ew32(STATUS, toggle);
 	after = er32(STATUS) & toggle;
 	if (value != after) {
-		DPRINTK(DRV, ERR, "failed STATUS register test got: "
-		        "0x%08X expected: 0x%08X\n", after, value);
+		e_err("failed STATUS register test got: "
+		      "0x%08X expected: 0x%08X\n", after, value);
 		*data = 1;
 		return 1;
 	}

@@ -894,8 +894,7 @@ static int e1000_intr_test(struct e1000_adapter *adapter, u64 *data)
 		*data = 1;
 		return -1;
 	}
-	DPRINTK(HW, INFO, "testing %s interrupt\n",
-	        (shared_int ? "shared" : "unshared"));
+	e_info("testing %s interrupt\n", (shared_int ? "shared" : "unshared"));
 
 	/* Disable all the interrupts */
 	ew32(IMC, 0xFFFFFFFF);

@@ -1564,7 +1563,7 @@ static void e1000_diag_test(struct net_device *netdev,
 		u8 forced_speed_duplex = hw->forced_speed_duplex;
 		u8 autoneg = hw->autoneg;
 
-		DPRINTK(HW, INFO, "offline testing starting\n");
+		e_info("offline testing starting\n");
 
 		/* Link test performed before hardware reset so autoneg doesn't
 		 * interfere with test result */

@@ -1604,7 +1603,7 @@ static void e1000_diag_test(struct net_device *netdev,
 		if (if_running)
 			dev_open(netdev);
 	} else {
-		DPRINTK(HW, INFO, "online testing starting\n");
+		e_info("online testing starting\n");
 		/* Online tests */
 		if (e1000_link_test(adapter, &data[4]))
 			eth_test->flags |= ETH_TEST_FL_FAILED;

@@ -1697,7 +1696,7 @@ static void e1000_get_wol(struct net_device *netdev,
 		wol->supported &= ~WAKE_UCAST;
 
 		if (adapter->wol & E1000_WUFC_EX)
-			DPRINTK(DRV, ERR, "Interface does not support "
+			e_err("Interface does not support "
 		        "directed (unicast) frame wake-up packets\n");
 		break;
 	default:

@@ -1731,8 +1730,8 @@ static int e1000_set_wol(struct net_device *netdev, struct ethtool_wolinfo *wol)
 	switch (hw->device_id) {
 	case E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3:
 		if (wol->wolopts & WAKE_UCAST) {
-			DPRINTK(DRV, ERR, "Interface does not support "
-		        "directed (unicast) frame wake-up packets\n");
+			e_err("Interface does not support "
+			      "directed (unicast) frame wake-up packets\n");
 			return -EOPNOTSUPP;
 		}
 		break;
drivers/net/e1000/e1000_hw.c +177 -179

1,288 lines not on this page · raw message

drivers/net/e1000/e1000_hw.h +1 -0
index 9acfddb..ecd9f6c 100644
@@ -35,6 +35,7 @@
 
 #include "e1000_osdep.h"
 
+
 /* Forward declarations of structures used by the shared code */
 struct e1000_hw;
 struct e1000_hw_stats;
drivers/net/e1000/e1000_main.c +114 -125

529 lines not on this page · raw message

drivers/net/e1000/e1000_osdep.h +0 -14
index d929852..edd1c75 100644
@@ -41,20 +41,6 @@
 #include <linux/interrupt.h>
 #include <linux/sched.h>
 
-#ifdef DBG
-#define DEBUGOUT(S)		printk(KERN_DEBUG S "\n")
-#define DEBUGOUT1(S, A...)	printk(KERN_DEBUG S "\n", A)
-#else
-#define DEBUGOUT(S)
-#define DEBUGOUT1(S, A...)
-#endif
-
-#define DEBUGFUNC(F) DEBUGOUT(F "\n")
-#define DEBUGOUT2 DEBUGOUT1
-#define DEBUGOUT3 DEBUGOUT2
-#define DEBUGOUT7 DEBUGOUT3
-
-
 #define er32(reg)							\
 	(readl(hw->hw_addr + ((hw->mac_type >= e1000_82543)		\
 			       ? E1000_##reg : E1000_82542_##reg)))
drivers/net/e1000/e1000_param.c +40 -54

215 lines not on this page · raw message

maintainer Applied
#1 lore raw

From: Jeff Kirsher <[email protected]>
Date: Tue, 27 Apr 2010 17:02:58 -0700

Quoted 12 lines

From: Emil Tantilov <[email protected]>

This patch is an alternative to similar patch provided by Joe Perches.

Substitute DPRINTK macro for e_<level> that uses netdev_<level> and dev_<level> similar to e1000e.
- Convert printk to pr_<level> where applicable.
- Use common #define pr_fmt for the driver.
- Use dev_<level> for displaying text in parts of the driver where the interface name is not assigned (like e1000_param.c).
- Better align test with the new macros.

Quoted 3 lines
CC Joe Perches <[email protected]>
Signed-off-by Emil Tantilov <[email protected]>
Signed-off-by Jeff Kirsher <[email protected]>

Applied, thanks.