Skip to contentSkip to conversation

ath9k: noise floor calibration process

ath9k-devel Benoit PAPILLAULT 4 participants 6 messages Apr 27, 2010 – Apr 28, 2010

lore
Share & tools
lore
#0 lore raw

Hello,

In order to move forward with noise & signal reporting, I'd like to share my current understanding of the way ath9k HW is working before sending patches (unfortunately, I did the work before the introduction of ar9003... so I need to redo the work).

The ultimate purpose of this work is to be able to measure signal levels (and noise if possible) as accurately as a spectrum analyzer or power meter.

First, signal level reporting. It is reported in a per packet basis in RX descriptors. There are 7 fields:

    AR_RxRSSIAnt00    0x000000ff    rs_rssi_ctl0
    AR_RxRSSIAnt01    0x0000ff00    rs_rssi_ctl1
    AR_RxRSSIAnt02    0x00ff0000    rs_rssi_ctl2
    AR_RxRSSIAnt10        0x000000ff    rs_rssi_ext0
    AR_RxRSSIAnt11        0x0000ff00    rs_rssi_ext1
    AR_RxRSSIAnt12        0x00ff0000    rs_rssi_ext2
    AR_RxRSSICombined    0xff000000    rs_rssi

Each value is for a 20 MHz wide channel, on the 3 RX chains. "ctl" is for the primary channel and "ext" is for the secondary channel (using the 802.11n words). The latter rs_rssi is the sum of the 6 previous value. However, since each value is dB, the sum is not an arithmetic sum. Each field is a signed value and the value -128 means that no measurement has been done (no RX chain, RX chain disabled, no secondary channel, ...). It seems that in some cases, the combined value is just plain wrong. Here are few examples:

RSSI: ctl=(10,7,-128) ext=(-128,-128,-128) => 12 (11.76) correct

RSSI: ctl=(38,29,-128) ext=(69,-84,-101) => -22 incorrect!!!

Next, noise floor calibration. From what I understand, signal levels is measured using the AGC + RX amplifiers gain (RF, IF and BB). However, the various gains are not really accurate, only the relative gain are accurate. This means that reading a signal value of -100dBm might not exactly means -100dBm. There is a delta between real signal and measured value. In order to know this value, we need a calibration process with a known signal.

One know signal is thermal noise. Thermal noise is generated in any resistor and can be computed using the well know value N = kTB. For a 20 MHz bandwidth, this gives -101dBm. If the HW tries to measure signal strength when the network is supposed to be idle (during SIFS) and with RX/TX switch disabled (?), then it will in fact measure the thermal noise at the RX input.

So, we have :

Real noise (-101dBm) = Measured noise + delta

There are type of registers to control noise floor calibration :

- control register at 0x9860 (AR_PHY_AGC_CONTROL)

This register allows 3 differents operations :

1. start noise floor measurement

write AR_PHY_MAXCCA_PWR (AR_PHY_CCA & 0x000001ff) : this is apparently
a max value
for noise floor
REG_SET_BIT(ah, AR_PHY_AGC_CONTROL, AR_PHY_AGC_CONTROL_ENABLE_NF); REG_SET_BIT(ah, AR_PHY_AGC_CONTROL, AR_PHY_AGC_CONTROL_NO_UPDATE_NF); REG_SET_BIT(ah, AR_PHY_AGC_CONTROL, AR_PHY_AGC_CONTROL_NF);

When channel has been changed however, the noise floor needs to be
updated immediately, so AR_PHY_AGC_CONTROL_NO_UPDATE_NF should be cleared in this particular case. Otherwise, the chip is no longer receiving (problem since CCA is defined with noise floor as reference).

2. read noise floor measurement result

check REG_READ(ah, AR_PHY_AGC_CONTROL) & AR_PHY_AGC_CONTROL_NF if 0 (noise floor calibration is finished), read AR_PHY_MINCCA_PWR :
nf = MS(REG_READ(ah, AR_PHY_CCA), AR_PHY_MINCCA_PWR = 0x0ff80000)

3. write noise floor reference

write AR_PHY_MAXCCA_PWR (the value has not the same meaning as
operation 1!)
REG_CLR_BIT(ah, AR_PHY_AGC_CONTROL, AR_PHY_AGC_CONTROL_ENABLE_NF); REG_CLR_BIT(ah, AR_PHY_AGC_CONTROL, AR_PHY_AGC_CONTROL_NO_UPDATE_NF); REG_SET_BIT(ah, AR_PHY_AGC_CONTROL, AR_PHY_AGC_CONTROL_NF);

- data register at 0x9864 (AR_PHY_CCA, + more location for other RX chains)

The fields are different for AR9280+ chipsets, but the mechanism is
the same.

    AR_PHY_MAXCCA_PWR        0x000001ff (half dBm unit!)
    AR_PHY_CCA_THRESH62    0x0007f000
    AR_PHY_MINCCA_PWR        0x0ff80000

Now, we have :

Real signal = Measured signal + delta
= RSSI + Noise floor + delta
= RSSI + (-101 dBm)

Real noise is not thermal noise. There are a lot of definition for noise since noise is NOT signal. Of course, noise includes thermal noise. Since the noise measured by the chip is variable, I think we could do :

- Noise floor = minimum (Noise floor measures)
- Noise = moving average (Noise floor measures) + delta with delta = (-101 dBm) - Noise floor

I'd like to get comments before sending patches. Since ath5k and ath9k are quite close, I'm pretty sure a similar (if not same) process is used on ath5k.

Regards,
Benoit

#1 lore raw

Hi All,

<preaching>

The chip *FOR SURE* *CANNOT* measure the thermal noise level!! It isn't
that sensitive. That said under some conditions it CAN measure the local interference level which IS useful.

I am *VERY MUCH* in favor of making real time level measurements of
various parts of real packets easy to use! Troubleshooting becomes so much easier :).

</preaching>

Great ideas !!

FWIW - I have on occasion used a low noise preamp to feed the chip.
Many more signals are detectable which "proves" the chip by itself *IS NOT* that sensitive. Try it yourself !

Have fun,

Wiz

Quoted 122 lines · Benoit PAPILLAULT

Hello,

In order to move forward with noise & signal reporting, I'd like to share my current understanding of the way ath9k HW is working before sending patches (unfortunately, I did the work before the introduction of ar9003... so I need to redo the work).

The ultimate purpose of this work is to be able to measure signal levels (and noise if possible) as accurately as a spectrum analyzer or power meter.

First, signal level reporting. It is reported in a per packet basis in RX descriptors. There are 7 fields:

    AR_RxRSSIAnt00    0x000000ff    rs_rssi_ctl0
    AR_RxRSSIAnt01    0x0000ff00    rs_rssi_ctl1
    AR_RxRSSIAnt02    0x00ff0000    rs_rssi_ctl2
    AR_RxRSSIAnt10        0x000000ff    rs_rssi_ext0
    AR_RxRSSIAnt11        0x0000ff00    rs_rssi_ext1
    AR_RxRSSIAnt12        0x00ff0000    rs_rssi_ext2
    AR_RxRSSICombined    0xff000000    rs_rssi

Each value is for a 20 MHz wide channel, on the 3 RX chains. "ctl" is for the primary channel and "ext" is for the secondary channel (using the 802.11n words). The latter rs_rssi is the sum of the 6 previous value. However, since each value is dB, the sum is not an arithmetic sum. Each field is a signed value and the value -128 means that no measurement has been done (no RX chain, RX chain disabled, no secondary channel, ...). It seems that in some cases, the combined value is just plain wrong. Here are few examples:

RSSI: ctl=(10,7,-128) ext=(-128,-128,-128) => 12 (11.76) correct

RSSI: ctl=(38,29,-128) ext=(69,-84,-101) => -22 incorrect!!!

Next, noise floor calibration. From what I understand, signal levels is measured using the AGC + RX amplifiers gain (RF, IF and BB). However, the various gains are not really accurate, only the relative gain are accurate. This means that reading a signal value of -100dBm might not exactly means -100dBm. There is a delta between real signal and measured value. In order to know this value, we need a calibration process with a known signal.

One know signal is thermal noise. Thermal noise is generated in any resistor and can be computed using the well know value N = kTB. For a 20 MHz bandwidth, this gives -101dBm. If the HW tries to measure signal strength when the network is supposed to be idle (during SIFS) and with RX/TX switch disabled (?), then it will in fact measure the thermal noise at the RX input.

So, we have :

Real noise (-101dBm) = Measured noise + delta

There are type of registers to control noise floor calibration :

- control register at 0x9860 (AR_PHY_AGC_CONTROL)

This register allows 3 differents operations :

1. start noise floor measurement

write AR_PHY_MAXCCA_PWR (AR_PHY_CCA & 0x000001ff) : this is apparently
a max value
for noise floor
REG_SET_BIT(ah, AR_PHY_AGC_CONTROL, AR_PHY_AGC_CONTROL_ENABLE_NF); REG_SET_BIT(ah, AR_PHY_AGC_CONTROL, AR_PHY_AGC_CONTROL_NO_UPDATE_NF); REG_SET_BIT(ah, AR_PHY_AGC_CONTROL, AR_PHY_AGC_CONTROL_NF);

When channel has been changed however, the noise floor needs to be
updated immediately, so AR_PHY_AGC_CONTROL_NO_UPDATE_NF should be cleared in this particular case. Otherwise, the chip is no longer receiving (problem since CCA is defined with noise floor as reference).

2. read noise floor measurement result

check REG_READ(ah, AR_PHY_AGC_CONTROL) & AR_PHY_AGC_CONTROL_NF if 0 (noise floor calibration is finished), read AR_PHY_MINCCA_PWR :
nf = MS(REG_READ(ah, AR_PHY_CCA), AR_PHY_MINCCA_PWR = 0x0ff80000)

3. write noise floor reference

write AR_PHY_MAXCCA_PWR (the value has not the same meaning as
operation 1!)
REG_CLR_BIT(ah, AR_PHY_AGC_CONTROL, AR_PHY_AGC_CONTROL_ENABLE_NF); REG_CLR_BIT(ah, AR_PHY_AGC_CONTROL, AR_PHY_AGC_CONTROL_NO_UPDATE_NF); REG_SET_BIT(ah, AR_PHY_AGC_CONTROL, AR_PHY_AGC_CONTROL_NF);

- data register at 0x9864 (AR_PHY_CCA, + more location for other RX chains)

The fields are different for AR9280+ chipsets, but the mechanism is
the same.

    AR_PHY_MAXCCA_PWR        0x000001ff (half dBm unit!)
    AR_PHY_CCA_THRESH62    0x0007f000
    AR_PHY_MINCCA_PWR        0x0ff80000

Now, we have :

Real signal = Measured signal + delta
= RSSI + Noise floor + delta
= RSSI + (-101 dBm)

Real noise is not thermal noise. There are a lot of definition for noise since noise is NOT signal. Of course, noise includes thermal noise. Since the noise measured by the chip is variable, I think we could do :

- Noise floor = minimum (Noise floor measures)
- Noise = moving average (Noise floor measures) + delta with delta = (-101 dBm) - Noise floor

I'd like to get comments before sending patches. Since ath5k and ath9k are quite close, I'm pretty sure a similar (if not same) process is used on ath5k.

Regards,
Benoit

_______________________________________________
ath9k-devel mailing list
ath9k-devel at lists.ath9k.org
https://lists.ath9k.org/mailman/listinfo/ath9k-devel

#2 lore raw

RHS Linux User a ?crit :

Quoted 8 lines

Hi All,

<preaching>

The chip *FOR SURE* *CANNOT* measure the thermal noise level!! It isn't
that sensitive. That said under some conditions it CAN measure the local interference level which IS useful.

In fact, that's what I thought first, but according to Atheros patent, it can. It seems pretty logic in fact : if you have no real signal at the input, you are measuring ambient noise. A spectrum analyzer is able to do it as well.

Sensitivity is the ability to decode 802.11 modulation out of the signal received (which includes any kind of noise). Using the formulas below, I measure the minimum signal levels of 802.11 packets by moving away from an AP and I indeed found -95dBm which is the typical sensitivity levels of an Atheros chip.

Quoted 4 lines

I am *VERY MUCH* in favor of making real time level measurements of
various parts of real packets easy to use! Troubleshooting becomes so much easier :).

Quoted 8 lines

</preaching>

Great ideas !!

FWIW - I have on occasion used a low noise preamp to feed the chip.
Many more signals are detectable which "proves" the chip by itself *IS NOT* that sensitive. Try it yourself !

Sure, in fact, I /think/ the thermal noise I'm talking is generated inside the first RX amplifier (it's probably generated in every RX amplifier, but the first is the biggest since it's amplified more than the others). So, if you put a low noise preamp, you are feeding the chip with more signal at the input but the chip has still the same amount of noise. Am I correct?

Quoted 4 lines

Have fun,

Wiz

Regards,
Benoit

Quoted 134 lines · Benoit PAPILLAULT
Quoted 116 lines

Hello,

In order to move forward with noise & signal reporting, I'd like to share my current understanding of the way ath9k HW is working before sending patches (unfortunately, I did the work before the introduction of ar9003... so I need to redo the work).

The ultimate purpose of this work is to be able to measure signal levels (and noise if possible) as accurately as a spectrum analyzer or power meter.

First, signal level reporting. It is reported in a per packet basis in RX descriptors. There are 7 fields:

    AR_RxRSSIAnt00    0x000000ff    rs_rssi_ctl0
    AR_RxRSSIAnt01    0x0000ff00    rs_rssi_ctl1
    AR_RxRSSIAnt02    0x00ff0000    rs_rssi_ctl2
    AR_RxRSSIAnt10        0x000000ff    rs_rssi_ext0
    AR_RxRSSIAnt11        0x0000ff00    rs_rssi_ext1
    AR_RxRSSIAnt12        0x00ff0000    rs_rssi_ext2
    AR_RxRSSICombined    0xff000000    rs_rssi

Each value is for a 20 MHz wide channel, on the 3 RX chains. "ctl" is for the primary channel and "ext" is for the secondary channel (using the 802.11n words). The latter rs_rssi is the sum of the 6 previous value. However, since each value is dB, the sum is not an arithmetic sum. Each field is a signed value and the value -128 means that no measurement has been done (no RX chain, RX chain disabled, no secondary channel, ...). It seems that in some cases, the combined value is just plain wrong. Here are few examples:

RSSI: ctl=(10,7,-128) ext=(-128,-128,-128) => 12 (11.76) correct

RSSI: ctl=(38,29,-128) ext=(69,-84,-101) => -22 incorrect!!!

Next, noise floor calibration. From what I understand, signal levels is measured using the AGC + RX amplifiers gain (RF, IF and BB). However, the various gains are not really accurate, only the relative gain are accurate. This means that reading a signal value of -100dBm might not exactly means -100dBm. There is a delta between real signal and measured value. In order to know this value, we need a calibration process with a known signal.

One know signal is thermal noise. Thermal noise is generated in any resistor and can be computed using the well know value N = kTB. For a 20 MHz bandwidth, this gives -101dBm. If the HW tries to measure signal strength when the network is supposed to be idle (during SIFS) and with RX/TX switch disabled (?), then it will in fact measure the thermal noise at the RX input.

So, we have :

Real noise (-101dBm) = Measured noise + delta

There are type of registers to control noise floor calibration :

- control register at 0x9860 (AR_PHY_AGC_CONTROL)

This register allows 3 differents operations :

1. start noise floor measurement

write AR_PHY_MAXCCA_PWR (AR_PHY_CCA & 0x000001ff) : this is apparently
a max value
for noise floor
REG_SET_BIT(ah, AR_PHY_AGC_CONTROL, AR_PHY_AGC_CONTROL_ENABLE_NF); REG_SET_BIT(ah, AR_PHY_AGC_CONTROL, AR_PHY_AGC_CONTROL_NO_UPDATE_NF); REG_SET_BIT(ah, AR_PHY_AGC_CONTROL, AR_PHY_AGC_CONTROL_NF);

When channel has been changed however, the noise floor needs to be
updated immediately, so AR_PHY_AGC_CONTROL_NO_UPDATE_NF should be cleared in this particular case. Otherwise, the chip is no longer receiving (problem since CCA is defined with noise floor as reference).

2. read noise floor measurement result

check REG_READ(ah, AR_PHY_AGC_CONTROL) & AR_PHY_AGC_CONTROL_NF if 0 (noise floor calibration is finished), read AR_PHY_MINCCA_PWR :
nf = MS(REG_READ(ah, AR_PHY_CCA), AR_PHY_MINCCA_PWR = 0x0ff80000)

3. write noise floor reference

write AR_PHY_MAXCCA_PWR (the value has not the same meaning as
operation 1!)
REG_CLR_BIT(ah, AR_PHY_AGC_CONTROL, AR_PHY_AGC_CONTROL_ENABLE_NF); REG_CLR_BIT(ah, AR_PHY_AGC_CONTROL, AR_PHY_AGC_CONTROL_NO_UPDATE_NF); REG_SET_BIT(ah, AR_PHY_AGC_CONTROL, AR_PHY_AGC_CONTROL_NF);

- data register at 0x9864 (AR_PHY_CCA, + more location for other RX chains)

The fields are different for AR9280+ chipsets, but the mechanism is
the same.

    AR_PHY_MAXCCA_PWR        0x000001ff (half dBm unit!)
    AR_PHY_CCA_THRESH62    0x0007f000
    AR_PHY_MINCCA_PWR        0x0ff80000

Now, we have :

Real signal = Measured signal + delta
= RSSI + Noise floor + delta
= RSSI + (-101 dBm)

Real noise is not thermal noise. There are a lot of definition for noise since noise is NOT signal. Of course, noise includes thermal noise. Since the noise measured by the chip is variable, I think we could do :

- Noise floor = minimum (Noise floor measures)
- Noise = moving average (Noise floor measures) + delta with delta = (-101 dBm) - Noise floor

I'd like to get comments before sending patches. Since ath5k and ath9k are quite close, I'm pretty sure a similar (if not same) process is used on ath5k.

Quoted 9 lines

Regards,
Benoit

_______________________________________________
ath9k-devel mailing list
ath9k-devel at lists.ath9k.org
https://lists.ath9k.org/mailman/listinfo/ath9k-devel

_______________________________________________
ath9k-devel mailing list
ath9k-devel at lists.ath9k.org
https://lists.ath9k.org/mailman/listinfo/ath9k-devel

#3 lore raw

Hi Benoit,

Yes. Having a patent is nice and probably significant too.

However, if using a preamp with a low noise figure results in
more signals or stronger (more error free) signals, then it IS better than the chip itself !!

It is VERY surprising that no chips I am aware of provide directly for
support of an external low noise preamp AND on a seperate coax a REAL amplifier.

In the USA Amateur radio operators can use 1000 Watts (under certain
conditions) !!

Now two high powered, low noise Acess Points with a clear line of sight
would give some real range!

warm regards,
Wiz

Quoted 178 lines · Benoit PAPILLAULT

RHS Linux User a ?crit :

Quoted 8 lines

Hi All,

<preaching>

The chip *FOR SURE* *CANNOT* measure the thermal noise level!! It isn't
that sensitive. That said under some conditions it CAN measure the local interference level which IS useful.

In fact, that's what I thought first, but according to Atheros patent, it can. It seems pretty logic in fact : if you have no real signal at the input, you are measuring ambient noise. A spectrum analyzer is able to do it as well.

Sensitivity is the ability to decode 802.11 modulation out of the signal received (which includes any kind of noise). Using the formulas below, I measure the minimum signal levels of 802.11 packets by moving away from an AP and I indeed found -95dBm which is the typical sensitivity levels of an Atheros chip.

Quoted 4 lines

I am *VERY MUCH* in favor of making real time level measurements of
various parts of real packets easy to use! Troubleshooting becomes so much easier :).

Quoted 8 lines

</preaching>

Great ideas !!

FWIW - I have on occasion used a low noise preamp to feed the chip.
Many more signals are detectable which "proves" the chip by itself *IS NOT* that sensitive. Try it yourself !

Sure, in fact, I /think/ the thermal noise I'm talking is generated inside the first RX amplifier (it's probably generated in every RX amplifier, but the first is the biggest since it's amplified more than the others). So, if you put a low noise preamp, you are feeding the chip with more signal at the input but the chip has still the same amount of noise. Am I correct?

Quoted 4 lines

Have fun,

Wiz

Regards,
Benoit

Quoted 134 lines · Benoit PAPILLAULT
Quoted 116 lines

Hello,

In order to move forward with noise & signal reporting, I'd like to share my current understanding of the way ath9k HW is working before sending patches (unfortunately, I did the work before the introduction of ar9003... so I need to redo the work).

The ultimate purpose of this work is to be able to measure signal levels (and noise if possible) as accurately as a spectrum analyzer or power meter.

First, signal level reporting. It is reported in a per packet basis in RX descriptors. There are 7 fields:

    AR_RxRSSIAnt00    0x000000ff    rs_rssi_ctl0
    AR_RxRSSIAnt01    0x0000ff00    rs_rssi_ctl1
    AR_RxRSSIAnt02    0x00ff0000    rs_rssi_ctl2
    AR_RxRSSIAnt10        0x000000ff    rs_rssi_ext0
    AR_RxRSSIAnt11        0x0000ff00    rs_rssi_ext1
    AR_RxRSSIAnt12        0x00ff0000    rs_rssi_ext2
    AR_RxRSSICombined    0xff000000    rs_rssi

Each value is for a 20 MHz wide channel, on the 3 RX chains. "ctl" is for the primary channel and "ext" is for the secondary channel (using the 802.11n words). The latter rs_rssi is the sum of the 6 previous value. However, since each value is dB, the sum is not an arithmetic sum. Each field is a signed value and the value -128 means that no measurement has been done (no RX chain, RX chain disabled, no secondary channel, ...). It seems that in some cases, the combined value is just plain wrong. Here are few examples:

RSSI: ctl=(10,7,-128) ext=(-128,-128,-128) => 12 (11.76) correct

RSSI: ctl=(38,29,-128) ext=(69,-84,-101) => -22 incorrect!!!

Next, noise floor calibration. From what I understand, signal levels is measured using the AGC + RX amplifiers gain (RF, IF and BB). However, the various gains are not really accurate, only the relative gain are accurate. This means that reading a signal value of -100dBm might not exactly means -100dBm. There is a delta between real signal and measured value. In order to know this value, we need a calibration process with a known signal.

One know signal is thermal noise. Thermal noise is generated in any resistor and can be computed using the well know value N = kTB. For a 20 MHz bandwidth, this gives -101dBm. If the HW tries to measure signal strength when the network is supposed to be idle (during SIFS) and with RX/TX switch disabled (?), then it will in fact measure the thermal noise at the RX input.

So, we have :

Real noise (-101dBm) = Measured noise + delta

There are type of registers to control noise floor calibration :

- control register at 0x9860 (AR_PHY_AGC_CONTROL)

This register allows 3 differents operations :

1. start noise floor measurement

write AR_PHY_MAXCCA_PWR (AR_PHY_CCA & 0x000001ff) : this is apparently
a max value
for noise floor
REG_SET_BIT(ah, AR_PHY_AGC_CONTROL, AR_PHY_AGC_CONTROL_ENABLE_NF); REG_SET_BIT(ah, AR_PHY_AGC_CONTROL, AR_PHY_AGC_CONTROL_NO_UPDATE_NF); REG_SET_BIT(ah, AR_PHY_AGC_CONTROL, AR_PHY_AGC_CONTROL_NF);

When channel has been changed however, the noise floor needs to be
updated immediately, so AR_PHY_AGC_CONTROL_NO_UPDATE_NF should be cleared in this particular case. Otherwise, the chip is no longer receiving (problem since CCA is defined with noise floor as reference).

2. read noise floor measurement result

check REG_READ(ah, AR_PHY_AGC_CONTROL) & AR_PHY_AGC_CONTROL_NF if 0 (noise floor calibration is finished), read AR_PHY_MINCCA_PWR :
nf = MS(REG_READ(ah, AR_PHY_CCA), AR_PHY_MINCCA_PWR = 0x0ff80000)

3. write noise floor reference

write AR_PHY_MAXCCA_PWR (the value has not the same meaning as
operation 1!)
REG_CLR_BIT(ah, AR_PHY_AGC_CONTROL, AR_PHY_AGC_CONTROL_ENABLE_NF); REG_CLR_BIT(ah, AR_PHY_AGC_CONTROL, AR_PHY_AGC_CONTROL_NO_UPDATE_NF); REG_SET_BIT(ah, AR_PHY_AGC_CONTROL, AR_PHY_AGC_CONTROL_NF);

- data register at 0x9864 (AR_PHY_CCA, + more location for other RX chains)

The fields are different for AR9280+ chipsets, but the mechanism is
the same.

    AR_PHY_MAXCCA_PWR        0x000001ff (half dBm unit!)
    AR_PHY_CCA_THRESH62    0x0007f000
    AR_PHY_MINCCA_PWR        0x0ff80000

Now, we have :

Real signal = Measured signal + delta
= RSSI + Noise floor + delta
= RSSI + (-101 dBm)

Real noise is not thermal noise. There are a lot of definition for noise since noise is NOT signal. Of course, noise includes thermal noise. Since the noise measured by the chip is variable, I think we could do :

- Noise floor = minimum (Noise floor measures)
- Noise = moving average (Noise floor measures) + delta with delta = (-101 dBm) - Noise floor

I'd like to get comments before sending patches. Since ath5k and ath9k are quite close, I'm pretty sure a similar (if not same) process is used on ath5k.

Quoted 9 lines

Regards,
Benoit

_______________________________________________
ath9k-devel mailing list
ath9k-devel at lists.ath9k.org
https://lists.ath9k.org/mailman/listinfo/ath9k-devel

_______________________________________________
ath9k-devel mailing list
ath9k-devel at lists.ath9k.org
https://lists.ath9k.org/mailman/listinfo/ath9k-devel

#4 lore raw
Quoted 2 lines

In the USA Amateur radio operators can use 1000 Watts (under certain
conditions) !!

Don't count on the 1000 W. Most countries have tight restrictions, only allowing certain frequencies, bandwiths, max PEP, max ERP, max EIRP, max electric field, max magnetic fields.

In Germany, with my license class, I can use up to 75W PEP in the frequency range 2320-2450 MHz. So, way less than 1000W. But I don't care, I wouldn't want to use 1000 W anyway. That's quite dangerous, e.g. if someone moves too near to the transmitting antenna.

Quoted 3 lines

It is VERY surprising that no chips I am aware of provide directly for support of an external low noise preamp AND on a seperate coax a REAL amplifier.

However, as licensed ham radio op, I'm allowed to build and use self-build equipment. That means, I'm not restricted to use only certified devices, e.g. I don't need some FCC or ZZF or whatever number on my equipment. So I'm perfectly eligible to add some pre-amp. And guess what, for frequencies above 100 MHz it's quite common to use low-noise pre-amps. Many HAMs do this, and also every satellite dish LNB does this.

I don't no chip "allowing" me this, I simply attach the pre-amp as near to the antenna as possible. How would a chip be able to prevent that anyway ?!?

Any WLAN chip provides for a separate coax. Again, how would a chip prevent against that? Only some hybrid chip with built-in antenne could possible prevent me doing that. But maybe you don't mean chips, but devices? Most USB dongles that I've seen won't provide a coax connector. But I have a bunch of PC-Card wlan cards with some SMA (or similar) coax connectors. And for Mini- PCI cards it's the common case to provide some coax socket.

Quoted 2 lines

Now two high powered, low noise Acess Points with a clear line of sight would give some real range!

Clear line of sight is nice, clear fresnel zone would be better.

Actually, what you're talking already happens already. It's called HAMNET. Some english language link that I found:

http://db0fhn.efi.fh-nuernberg.de/doku.php?id=projects:wlan:hamnet

Oh, and they use atheros hardware :-)

#5 lore raw
Quoted 4 lines · Holger Schurig
Quoted 2 lines

Now two high powered, low noise Acess Points with a clear line of sight would give some real range!

HAMNET

And http://tier.cs.berkeley.edu/wiki/Wireless which changes the MAC layer a bit, for very nice gain in performance.

//Peter