Skip to contentSkip to conversation

Resend: Libata delay patches

PATCH Applied Alan Cox 4 participants 12 messages May 5, 2010 – Jun 10, 2010 libata

lore
Share & tools
lore

Alan Cox

author
#0 lore raw

cover Resend: Libata delay patches

Alan Cox (3):
libata: Make sil680 do its own exec_command posting
libata: Remove excess command issue delays
libata: Remove excess delay in the tf_load path

author
#1 lore raw

PATCH 1/3 libata: Remove excess delay in the tf_load path

We don't need to stall and wait after loading the task file and before issuing a command, so don't do it. This shows up on profiles and is not needed.

---

 drivers/ata/libata-sff.c |    3 ---
 drivers/ata/pata_via.c   |    2 --
 2 files changed, 0 insertions(+), 5 deletions(-)
drivers/ata/libata-sff.c +0 -3
index b313896..17754a7 100644
@@ -579,7 +579,6 @@ void ata_sff_tf_load(struct ata_port *ap, const struct ata_taskfile *tf)
 		if (ioaddr->ctl_addr)
 			iowrite8(tf->ctl, ioaddr->ctl_addr);
 		ap->last_ctl = tf->ctl;
-		ata_wait_idle(ap);
 	}
 
 	if (is_addr && (tf->flags & ATA_TFLAG_LBA48)) {
@@ -615,8 +614,6 @@ void ata_sff_tf_load(struct ata_port *ap, const struct ata_taskfile *tf)
 		iowrite8(tf->device, ioaddr->device_addr);
 		VPRINTK("device 0x%X\n", tf->device);
 	}
-
-	ata_wait_idle(ap);
 }
 EXPORT_SYMBOL_GPL(ata_sff_tf_load);
 
drivers/ata/pata_via.c +0 -2
index 741e7cb..87fb89e 100644
@@ -417,8 +417,6 @@ static void via_tf_load(struct ata_port *ap, const struct ata_taskfile *tf)
 			tf->lbam,
 			tf->lbah);
 	}
-
-	ata_wait_idle(ap);
 }
 
 static int via_port_start(struct ata_port *ap)
#2 lore raw

Re: [PATCH 1/3] libata: Remove excess delay in the tf_load path

Hello.

Quoted 2 lines · Alan Cox

We don't need to stall and wait after loading the task file and before

You mean *before* loading the taskfile?

Quoted 3 lines

issuing a command, so don't do it. This shows up on profiles and is not needed.

The same wait is in sff_irq_on() method, I doubt that it's really
necessary as well, given that its result is always ignored...

Quoted 35 lines

---

 drivers/ata/libata-sff.c |    3 ---
 drivers/ata/pata_via.c   |    2 --
 2 files changed, 0 insertions(+), 5 deletions(-)
drivers/ata/libata-sff.c +0 -3
index b313896..17754a7 100644
@@ -579,7 +579,6 @@ void ata_sff_tf_load(struct ata_port *ap, const struct ata_taskfile *tf)
 		if (ioaddr->ctl_addr)
 			iowrite8(tf->ctl, ioaddr->ctl_addr);
 		ap->last_ctl = tf->ctl;
-		ata_wait_idle(ap);
 	}
 
 	if (is_addr && (tf->flags & ATA_TFLAG_LBA48)) {
@@ -615,8 +614,6 @@ void ata_sff_tf_load(struct ata_port *ap, const struct ata_taskfile *tf)
 		iowrite8(tf->device, ioaddr->device_addr);
 		VPRINTK("device 0x%X\n", tf->device);
 	}
-
-	ata_wait_idle(ap);
 }
 EXPORT_SYMBOL_GPL(ata_sff_tf_load);
 
drivers/ata/pata_via.c +0 -0
index 741e7cb..87fb89e 100644

drivers/ata/pata_via.c static void via_tf_load(struct ata_port *ap, const struct ata_taskfile *tf) · line 422

Quoted 8 lines
drivers/ata/pata_via.c +0 -2
@@ -417,8 +417,6 @@ static void via_tf_load(struct ata_port *ap, const struct ata_taskfile *tf)
 			tf->lbam,
 			tf->lbah);
 	}
-
-	ata_wait_idle(ap);
 }
 
 static int via_port_start(struct ata_port *ap)

WBR, Sergei

#3 lore raw

Re: [PATCH 1/3] libata: Remove excess delay in the tf_load path

Quoted 8 lines · On Wed, 05 May 2010 14:24:14 +0400 Sergei Shtylyov <[email protected]> wrote:

Hello.

Quoted 2 lines · Alan Cox

We don't need to stall and wait after loading the task file and before

You mean *before* loading the taskfile?

It removes the stall between loading the task file and issuing the command. I'll make the comment clearer about the ctl one.

Quoted 2 lines

The same wait is in sff_irq_on() method, I doubt that it's really
necessary as well, given that its result is always ignored...

Will have a look at that as a possible follow up patch.

Applied
#4 lore raw

Re: [PATCH 1/3] libata: Remove excess delay in the tf_load path

In reply to Alan Cox
Quoted 10 lines · Alan Cox

We don't need to stall and wait after loading the task file and before issuing a command, so don't do it. This shows up on profiles and is not needed.

---

  drivers/ata/libata-sff.c |    3 ---
  drivers/ata/pata_via.c   |    2 --
  2 files changed, 0 insertions(+), 5 deletions(-)

applied

author
#5 lore raw

PATCH 2/3 libata: Remove excess command issue delays

In reply to Alan Cox

We don't need to pause before a command issue for PIO (it's posted) or for most MMIO devices (internally managed delay) so provide a routine for the normal "sane" hardware

As a side effect it also means that those devices using PIO don't end up generating ATA bus cycles in strange places which confuses some hardware.

---

 drivers/ata/ata_generic.c       |    7 +++---
 drivers/ata/ata_piix.c          |    1 +
 drivers/ata/libata-sff.c        |   25 ++++++++++++++++++++
 drivers/ata/pata_acpi.c         |    1 +
 drivers/ata/pata_ali.c          |   16 +++++++------
 drivers/ata/pata_amd.c          |   48 ++++++++++++++++++++-------------------
 drivers/ata/pata_artop.c        |    2 ++
 drivers/ata/pata_atiixp.c       |   15 +++++++-----
 drivers/ata/pata_atp867x.c      |    1 +
 drivers/ata/pata_cmd640.c       |   13 ++++++-----
 drivers/ata/pata_cmd64x.c       |   23 ++++++++++---------
 drivers/ata/pata_cs5520.c       |    1 +
 drivers/ata/pata_cs5530.c       |   13 ++++++-----
 drivers/ata/pata_cs5535.c       |    9 ++++---
 drivers/ata/pata_cs5536.c       |    1 +
 drivers/ata/pata_efar.c         |    1 +
 drivers/ata/pata_hpt366.c       |   11 +++++----
 drivers/ata/pata_hpt37x.c       |   36 +++++++++++++++--------------
 drivers/ata/pata_hpt3x2n.c      |   17 +++++++-------
 drivers/ata/pata_isapnp.c       |    5 ++--
 drivers/ata/pata_it8213.c       |    1 +
 drivers/ata/pata_it821x.c       |   42 ++++++++++++++++++----------------
 drivers/ata/pata_jmicron.c      |    1 +
 drivers/ata/pata_legacy.c       |    5 ++--
 drivers/ata/pata_marvell.c      |    1 +
 drivers/ata/pata_mpiix.c        |   13 ++++++-----
 drivers/ata/pata_netcell.c      |    7 +++---
 drivers/ata/pata_ns87410.c      |   11 +++++----
 drivers/ata/pata_ns87415.c      |    1 +
 drivers/ata/pata_oldpiix.c      |    1 +
 drivers/ata/pata_opti.c         |    9 ++++---
 drivers/ata/pata_optidma.c      |   19 ++++++++-------
 drivers/ata/pata_pcmcia.c       |   19 ++++++++-------
 drivers/ata/pata_pdc202xx_old.c |    1 +
 drivers/ata/pata_piccolo.c      |    9 ++++---
 drivers/ata/pata_qdi.c          |   15 +++++++-----
 drivers/ata/pata_radisys.c      |    1 +
 drivers/ata/pata_rdc.c          |    1 +
 drivers/ata/pata_rz1000.c       |    7 +++---
 drivers/ata/pata_sc1200.c       |   15 +++++++-----
 drivers/ata/pata_sch.c          |    1 +
 drivers/ata/pata_serverworks.c  |   11 +++++----
 drivers/ata/pata_sis.c          |    2 ++
 drivers/ata/pata_triflex.c      |   13 ++++++-----
 drivers/ata/pata_via.c          |   17 +++++++-------
 drivers/ata/pata_winbond.c      |    9 ++++---
 include/linux/libata.h          |    2 ++
 47 files changed, 278 insertions(+), 202 deletions(-)
drivers/ata/ata_generic.c +4 -3
index 33fb614..7b605e5 100644
@@ -96,9 +96,10 @@ static struct scsi_host_template generic_sht = {
 };
 
 static struct ata_port_operations generic_port_ops = {
-	.inherits	= &ata_bmdma_port_ops,
-	.cable_detect	= ata_cable_unknown,
-	.set_mode	= generic_set_mode,
+	.inherits		= &ata_bmdma_port_ops,
+	.sff_exec_command	= ata_sff_exec_command_nopost,
+	.cable_detect		= ata_cable_unknown,
+	.set_mode		= generic_set_mode,
 };
 
 static int all_generic_ide;		/* Set to claim all devices */
drivers/ata/ata_piix.c +1 -0
index ec52fc6..004a9c3 100644
@@ -321,6 +321,7 @@ static struct scsi_host_template piix_sht = {
 
 static struct ata_port_operations piix_sata_ops = {
 	.inherits		= &ata_bmdma32_port_ops,
+	.sff_exec_command	= ata_sff_exec_command_nopost,
 	.sff_irq_check		= piix_irq_check,
 };
 
drivers/ata/libata-sff.c +24 -1
index 17754a7..4b57ae9 100644
@@ -674,11 +674,34 @@ void ata_sff_exec_command(struct ata_port *ap, const struct ata_taskfile *tf)
 	DPRINTK("ata%u: cmd 0x%X\n", ap->print_id, tf->command);
 
 	iowrite8(tf->command, ap->ioaddr.command_addr);
-	ata_sff_pause(ap);
+	/* Slow */
+        ata_sff_pause(ap);
 }
 EXPORT_SYMBOL_GPL(ata_sff_exec_command);
 
 /**
+ *	ata_sff_exec_command_nopost - issue ATA command to host controller
+ *	@ap: port to which command is being issued
+ *	@tf: ATA taskfile register set
+ *
+ *	Issues ATA command, with proper synchronization with interrupt
+ *	handler / other threads. This version of the helper does not protect
+ *	against any delayed writes done by the underlying fabric, it must
+ *	therefore not be used for MMIO devices unless the device handles
+ *	the 400nS command delay stall internally.
+ *
+ *	LOCKING:
+ *	spin_lock_irqsave(host lock)
+ */
+void ata_sff_exec_command_nopost(struct ata_port *ap,
+                                        const struct ata_taskfile *tf)
+{
+	DPRINTK("ata%u: cmd 0x%X\n", ap->print_id, tf->command);
+	iowrite8(tf->command, ap->ioaddr.command_addr);
+}
+EXPORT_SYMBOL_GPL(ata_sff_exec_command_nopost);
+
+/**
  *	ata_tf_to_host - issue ATA taskfile to host controller
  *	@ap: port to which command is being issued
  *	@tf: ATA taskfile register set
drivers/ata/pata_acpi.c +1 -0
index 1ea2be0..e56a814 100644
@@ -218,6 +218,7 @@ static struct scsi_host_template pacpi_sht = {
 
 static struct ata_port_operations pacpi_ops = {
 	.inherits		= &ata_bmdma_port_ops,
+	.sff_exec_command	= ata_sff_exec_command_nopost,
 	.qc_issue		= pacpi_qc_issue,
 	.cable_detect		= pacpi_cable_detect,
 	.mode_filter		= pacpi_mode_filter,
drivers/ata/pata_ali.c +9 -7
index dc61b72..e79cb78 100644
@@ -364,16 +364,18 @@ static struct scsi_host_template ali_sht = {
  */
 
 static struct ata_port_operations ali_early_port_ops = {
-	.inherits	= &ata_sff_port_ops,
-	.cable_detect	= ata_cable_40wire,
-	.set_piomode	= ali_set_piomode,
-	.sff_data_xfer  = ata_sff_data_xfer32,
+	.inherits		= &ata_sff_port_ops,
+	.sff_exec_command	= ata_sff_exec_command_nopost,
+	.cable_detect		= ata_cable_40wire,
+	.set_piomode		= ali_set_piomode,
+	.sff_data_xfer  	= ata_sff_data_xfer32,
 };
 
 static const struct ata_port_operations ali_dma_base_ops = {
-	.inherits	= &ata_bmdma32_port_ops,
-	.set_piomode	= ali_set_piomode,
-	.set_dmamode	= ali_set_dmamode,
+	.inherits		= &ata_bmdma32_port_ops,
+	.sff_exec_command	= ata_sff_exec_command_nopost,
+	.set_piomode		= ali_set_piomode,
+	.set_dmamode		= ali_set_dmamode,
 };
 
 /*
drivers/ata/pata_amd.c +25 -23

69 lines not on this page · raw message

drivers/ata/pata_artop.c +2 -0
index 4d066d6..6ed1de5 100644
@@ -313,6 +313,7 @@ static struct scsi_host_template artop_sht = {
 
 static struct ata_port_operations artop6210_ops = {
 	.inherits		= &ata_bmdma_port_ops,
+	.sff_exec_command	= ata_sff_exec_command_nopost,
 	.cable_detect		= ata_cable_40wire,
 	.set_piomode		= artop6210_set_piomode,
 	.set_dmamode		= artop6210_set_dmamode,
@@ -322,6 +323,7 @@ static struct ata_port_operations artop6210_ops = {
 
 static struct ata_port_operations artop6260_ops = {
 	.inherits		= &ata_bmdma_port_ops,
+	.sff_exec_command	= ata_sff_exec_command_nopost,
 	.cable_detect		= artop6260_cable_detect,
 	.set_piomode		= artop6260_set_piomode,
 	.set_dmamode		= artop6260_set_dmamode,
drivers/ata/pata_atiixp.c +8 -7
index cbaf2ed..017e6e1 100644
@@ -215,15 +215,16 @@ static struct scsi_host_template atiixp_sht = {
 };
 
 static struct ata_port_operations atiixp_port_ops = {
-	.inherits	= &ata_bmdma_port_ops,
+	.inherits		= &ata_bmdma_port_ops,
 
-	.qc_prep 	= ata_sff_dumb_qc_prep,
-	.bmdma_start 	= atiixp_bmdma_start,
-	.bmdma_stop	= atiixp_bmdma_stop,
+	.sff_exec_command	= ata_sff_exec_command_nopost,
+	.qc_prep 		= ata_sff_dumb_qc_prep,
+	.bmdma_start 		= atiixp_bmdma_start,
+	.bmdma_stop		= atiixp_bmdma_stop,
 
-	.cable_detect	= atiixp_cable_detect,
-	.set_piomode	= atiixp_set_piomode,
-	.set_dmamode	= atiixp_set_dmamode,
+	.cable_detect		= atiixp_cable_detect,
+	.set_piomode		= atiixp_set_piomode,
+	.set_dmamode		= atiixp_set_dmamode,
 };
 
 static int atiixp_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
drivers/ata/pata_atp867x.c +1 -0
index bb6e074..2559f0a 100644
@@ -277,6 +277,7 @@ static struct scsi_host_template atp867x_sht = {
 
 static struct ata_port_operations atp867x_ops = {
 	.inherits		= &ata_bmdma_port_ops,
+	.sff_exec_command	= ata_sff_exec_command_nopost,
 	.cable_detect		= atp867x_cable_detect,
 	.set_piomode		= atp867x_set_piomode,
 	.set_dmamode		= atp867x_set_dmamode,
drivers/ata/pata_cmd640.c +7 -6
index 45896b3..8abee7b 100644
@@ -170,13 +170,14 @@ static struct scsi_host_template cmd640_sht = {
 };
 
 static struct ata_port_operations cmd640_port_ops = {
-	.inherits	= &ata_bmdma_port_ops,
+	.inherits		= &ata_bmdma_port_ops,
 	/* In theory xfer_noirq is not needed once we kill the prefetcher */
-	.sff_data_xfer	= ata_sff_data_xfer_noirq,
-	.qc_issue	= cmd640_qc_issue,
-	.cable_detect	= ata_cable_40wire,
-	.set_piomode	= cmd640_set_piomode,
-	.port_start	= cmd640_port_start,
+	.sff_exec_command	= ata_sff_exec_command_nopost,
+	.sff_data_xfer		= ata_sff_data_xfer_noirq,
+	.qc_issue		= cmd640_qc_issue,
+	.cable_detect		= ata_cable_40wire,
+	.set_piomode		= cmd640_set_piomode,
+	.port_start		= cmd640_port_start,
 };
 
 static void cmd640_hardware_init(struct pci_dev *pdev)
drivers/ata/pata_cmd64x.c +12 -11
index 4c81a71..5a438c4 100644
@@ -269,26 +269,27 @@ static struct scsi_host_template cmd64x_sht = {
 };
 
 static const struct ata_port_operations cmd64x_base_ops = {
-	.inherits	= &ata_bmdma_port_ops,
-	.set_piomode	= cmd64x_set_piomode,
-	.set_dmamode	= cmd64x_set_dmamode,
+	.inherits		= &ata_bmdma_port_ops,
+	.sff_exec_command	= ata_sff_exec_command_nopost,
+	.set_piomode		= cmd64x_set_piomode,
+	.set_dmamode		= cmd64x_set_dmamode,
 };
 
 static struct ata_port_operations cmd64x_port_ops = {
-	.inherits	= &cmd64x_base_ops,
-	.cable_detect	= ata_cable_40wire,
+	.inherits		= &cmd64x_base_ops,
+	.cable_detect		= ata_cable_40wire,
 };
 
 static struct ata_port_operations cmd646r1_port_ops = {
-	.inherits	= &cmd64x_base_ops,
-	.bmdma_stop	= cmd646r1_bmdma_stop,
-	.cable_detect	= ata_cable_40wire,
+	.inherits		= &cmd64x_base_ops,
+	.bmdma_stop		= cmd646r1_bmdma_stop,
+	.cable_detect		= ata_cable_40wire,
 };
 
 static struct ata_port_operations cmd648_port_ops = {
-	.inherits	= &cmd64x_base_ops,
-	.bmdma_stop	= cmd648_bmdma_stop,
-	.cable_detect	= cmd648_cable_detect,
+	.inherits		= &cmd64x_base_ops,
+	.bmdma_stop		= cmd648_bmdma_stop,
+	.cable_detect		= cmd648_cable_detect,
 };
 
 static int cmd64x_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
drivers/ata/pata_cs5520.c +1 -0
index 95ebdac..dab33ce 100644
@@ -110,6 +110,7 @@ static struct scsi_host_template cs5520_sht = {
 
 static struct ata_port_operations cs5520_port_ops = {
 	.inherits		= &ata_bmdma_port_ops,
+	.sff_exec_command	= ata_sff_exec_command_nopost,
 	.qc_prep		= ata_sff_dumb_qc_prep,
 	.cable_detect		= ata_cable_40wire,
 	.set_piomode		= cs5520_set_piomode,
drivers/ata/pata_cs5530.c +7 -6
index 738ad2e..5244053 100644
@@ -165,14 +165,15 @@ static struct scsi_host_template cs5530_sht = {
 };
 
 static struct ata_port_operations cs5530_port_ops = {
-	.inherits	= &ata_bmdma_port_ops,
+	.inherits		= &ata_bmdma_port_ops,
 
-	.qc_prep 	= ata_sff_dumb_qc_prep,
-	.qc_issue	= cs5530_qc_issue,
+	.sff_exec_command	= ata_sff_exec_command_nopost,
+	.qc_prep 		= ata_sff_dumb_qc_prep,
+	.qc_issue		= cs5530_qc_issue,
 
-	.cable_detect	= ata_cable_40wire,
-	.set_piomode	= cs5530_set_piomode,
-	.set_dmamode	= cs5530_set_dmamode,
+	.cable_detect		= ata_cable_40wire,
+	.set_piomode		= cs5530_set_piomode,
+	.set_dmamode		= cs5530_set_dmamode,
 };
 
 static const struct dmi_system_id palmax_dmi_table[] = {
drivers/ata/pata_cs5535.c +5 -4
index a02e645..0c470e7 100644
@@ -161,10 +161,11 @@ static struct scsi_host_template cs5535_sht = {
 };
 
 static struct ata_port_operations cs5535_port_ops = {
-	.inherits	= &ata_bmdma_port_ops,
-	.cable_detect	= cs5535_cable_detect,
-	.set_piomode	= cs5535_set_piomode,
-	.set_dmamode	= cs5535_set_dmamode,
+	.inherits		= &ata_bmdma_port_ops,
+	.sff_exec_command	= ata_sff_exec_command_nopost,
+	.cable_detect		= cs5535_cable_detect,
+	.set_piomode		= cs5535_set_piomode,
+	.set_dmamode		= cs5535_set_dmamode,
 };
 
 /**
drivers/ata/pata_cs5536.c +1 -0
index 914ae35..f354db9 100644
@@ -225,6 +225,7 @@ static struct scsi_host_template cs5536_sht = {
 
 static struct ata_port_operations cs5536_port_ops = {
 	.inherits		= &ata_bmdma32_port_ops,
+	.sff_exec_command	= ata_sff_exec_command_nopost,
 	.cable_detect		= cs5536_cable_detect,
 	.set_piomode		= cs5536_set_piomode,
 	.set_dmamode		= cs5536_set_dmamode,
drivers/ata/pata_efar.c +1 -0
index 3bac0e0..4289db0 100644
@@ -240,6 +240,7 @@ static struct scsi_host_template efar_sht = {
 
 static struct ata_port_operations efar_ops = {
 	.inherits		= &ata_bmdma_port_ops,
+	.sff_exec_command	= ata_sff_exec_command_nopost,
 	.cable_detect		= efar_cable_detect,
 	.set_piomode		= efar_set_piomode,
 	.set_dmamode		= efar_set_dmamode,
drivers/ata/pata_hpt366.c +6 -5
index af49bfb..66a7036 100644
@@ -270,11 +270,12 @@ static struct scsi_host_template hpt36x_sht = {
  */
 
 static struct ata_port_operations hpt366_port_ops = {
-	.inherits	= &ata_bmdma_port_ops,
-	.cable_detect	= hpt36x_cable_detect,
-	.mode_filter	= hpt366_filter,
-	.set_piomode	= hpt366_set_piomode,
-	.set_dmamode	= hpt366_set_dmamode,
+	.inherits		= &ata_bmdma_port_ops,
+	.sff_exec_command	= ata_sff_exec_command_nopost,
+	.cable_detect		= hpt36x_cable_detect,
+	.mode_filter		= hpt366_filter,
+	.set_piomode		= hpt366_set_piomode,
+	.set_dmamode		= hpt366_set_dmamode,
 };
 
 /**
drivers/ata/pata_hpt37x.c +19 -17
index 8839307..3cf48b8 100644
@@ -565,15 +565,16 @@ static struct scsi_host_template hpt37x_sht = {
  */
 
 static struct ata_port_operations hpt370_port_ops = {
-	.inherits	= &ata_bmdma_port_ops,
+	.inherits		= &ata_bmdma_port_ops,
 
-	.bmdma_stop	= hpt370_bmdma_stop,
+	.sff_exec_command	= ata_sff_exec_command_nopost,
+	.bmdma_stop		= hpt370_bmdma_stop,
 
-	.mode_filter	= hpt370_filter,
-	.cable_detect	= hpt37x_cable_detect,
-	.set_piomode	= hpt370_set_piomode,
-	.set_dmamode	= hpt370_set_dmamode,
-	.prereset	= hpt37x_pre_reset,
+	.mode_filter		= hpt370_filter,
+	.cable_detect		= hpt37x_cable_detect,
+	.set_piomode		= hpt370_set_piomode,
+	.set_dmamode		= hpt370_set_dmamode,
+	.prereset		= hpt37x_pre_reset,
 };
 
 /*
@@ -581,8 +582,8 @@ static struct ata_port_operations hpt370_port_ops = {
  */
 
 static struct ata_port_operations hpt370a_port_ops = {
-	.inherits	= &hpt370_port_ops,
-	.mode_filter	= hpt370a_filter,
+	.inherits		= &hpt370_port_ops,
+	.mode_filter		= hpt370a_filter,
 };
 
 /*
@@ -593,12 +594,13 @@ static struct ata_port_operations hpt370a_port_ops = {
 static struct ata_port_operations hpt372_port_ops = {
 	.inherits	= &ata_bmdma_port_ops,
 
-	.bmdma_stop	= hpt37x_bmdma_stop,
+	.sff_exec_command	= ata_sff_exec_command_nopost,
+	.bmdma_stop		= hpt37x_bmdma_stop,
 
-	.cable_detect	= hpt37x_cable_detect,
-	.set_piomode	= hpt372_set_piomode,
-	.set_dmamode	= hpt372_set_dmamode,
-	.prereset	= hpt37x_pre_reset,
+	.cable_detect		= hpt37x_cable_detect,
+	.set_piomode		= hpt372_set_piomode,
+	.set_dmamode		= hpt372_set_dmamode,
+	.prereset		= hpt37x_pre_reset,
 };
 
 /*
@@ -607,9 +609,9 @@ static struct ata_port_operations hpt372_port_ops = {
  */
 
 static struct ata_port_operations hpt374_fn1_port_ops = {
-	.inherits	= &hpt372_port_ops,
-	.cable_detect	= hpt374_fn1_cable_detect,
-	.prereset	= hpt37x_pre_reset,
+	.inherits		= &hpt372_port_ops,
+	.cable_detect		= hpt374_fn1_cable_detect,
+	.prereset		= hpt37x_pre_reset,
 };
 
 /**
drivers/ata/pata_hpt3x2n.c +9 -8
index 01457b2..c69c871 100644
@@ -332,17 +332,18 @@ static struct scsi_host_template hpt3x2n_sht = {
  */
 
 static struct ata_port_operations hpt3x2n_port_ops = {
-	.inherits	= &ata_bmdma_port_ops,
+	.inherits		= &ata_bmdma_port_ops,
 
-	.bmdma_stop	= hpt3x2n_bmdma_stop,
+	.sff_exec_command	= ata_sff_exec_command_nopost,
+	.bmdma_stop		= hpt3x2n_bmdma_stop,
 
-	.qc_defer	= hpt3x2n_qc_defer,
-	.qc_issue	= hpt3x2n_qc_issue,
+	.qc_defer		= hpt3x2n_qc_defer,
+	.qc_issue		= hpt3x2n_qc_issue,
 
-	.cable_detect	= hpt3x2n_cable_detect,
-	.set_piomode	= hpt3x2n_set_piomode,
-	.set_dmamode	= hpt3x2n_set_dmamode,
-	.prereset	= hpt3x2n_pre_reset,
+	.cable_detect		= hpt3x2n_cable_detect,
+	.set_piomode		= hpt3x2n_set_piomode,
+	.set_dmamode		= hpt3x2n_set_dmamode,
+	.prereset		= hpt3x2n_pre_reset,
 };
 
 /**
drivers/ata/pata_isapnp.c +3 -2
index 4bceb88..35df122 100644
@@ -24,8 +24,9 @@ static struct scsi_host_template isapnp_sht = {
 };
 
 static struct ata_port_operations isapnp_port_ops = {
-	.inherits	= &ata_sff_port_ops,
-	.cable_detect	= ata_cable_40wire,
+	.inherits		= &ata_sff_port_ops,
+	.sff_exec_command	= ata_sff_exec_command_nopost,
+	.cable_detect		= ata_cable_40wire,
 };
 
 static struct ata_port_operations isapnp_noalt_port_ops = {
drivers/ata/pata_it8213.c +1 -0
index f971f0d..daace8f 100644
@@ -235,6 +235,7 @@ static struct scsi_host_template it8213_sht = {
 
 static struct ata_port_operations it8213_ops = {
 	.inherits		= &ata_bmdma_port_ops,
+	.sff_exec_command	= ata_sff_exec_command_nopost,
 	.cable_detect		= it8213_cable_detect,
 	.set_piomode		= it8213_set_piomode,
 	.set_dmamode		= it8213_set_dmamode,
drivers/ata/pata_it821x.c +22 -20

57 lines not on this page · raw message

drivers/ata/pata_jmicron.c +1 -0
index 565e01e..a28382b 100644
@@ -113,6 +113,7 @@ static struct scsi_host_template jmicron_sht = {
 
 static struct ata_port_operations jmicron_ops = {
 	.inherits		= &ata_bmdma_port_ops,
+	.sff_exec_command	= ata_sff_exec_command_nopost,
 	.prereset		= jmicron_pre_reset,
 };
 
drivers/ata/pata_legacy.c +3 -2
index 9df1ff7..76b31c7 100644
@@ -218,8 +218,9 @@ static struct scsi_host_template legacy_sht = {
 };
 
 static const struct ata_port_operations legacy_base_port_ops = {
-	.inherits	= &ata_sff_port_ops,
-	.cable_detect	= ata_cable_40wire,
+	.inherits		= &ata_sff_port_ops,
+	.sff_exec_command	= ata_sff_exec_command_nopost,
+	.cable_detect		= ata_cable_40wire,
 };
 
 /*
drivers/ata/pata_marvell.c +1 -0
index e8ca02e..8da0c82 100644
@@ -102,6 +102,7 @@ static struct scsi_host_template marvell_sht = {
 
 static struct ata_port_operations marvell_ops = {
 	.inherits		= &ata_bmdma_port_ops,
+	.sff_exec_command	= ata_sff_exec_command_nopost,
 	.cable_detect		= marvell_cable_detect,
 	.prereset		= marvell_pre_reset,
 };
drivers/ata/pata_mpiix.c +7 -6
index b21f002..2be0ccd 100644
@@ -141,12 +141,13 @@ static struct scsi_host_template mpiix_sht = {
 };
 
 static struct ata_port_operations mpiix_port_ops = {
-	.inherits	= &ata_sff_port_ops,
-	.qc_issue	= mpiix_qc_issue,
-	.cable_detect	= ata_cable_40wire,
-	.set_piomode	= mpiix_set_piomode,
-	.prereset	= mpiix_pre_reset,
-	.sff_data_xfer	= ata_sff_data_xfer32,
+	.inherits		= &ata_sff_port_ops,
+	.sff_exec_command	= ata_sff_exec_command_nopost,
+	.qc_issue		= mpiix_qc_issue,
+	.cable_detect		= ata_cable_40wire,
+	.set_piomode		= mpiix_set_piomode,
+	.prereset		= mpiix_pre_reset,
+	.sff_data_xfer		= ata_sff_data_xfer32,
 };
 
 static int mpiix_init_one(struct pci_dev *dev, const struct pci_device_id *id)
drivers/ata/pata_netcell.c +4 -3
index 94f979a..5fea4d7 100644
@@ -35,9 +35,10 @@ static struct scsi_host_template netcell_sht = {
 };
 
 static struct ata_port_operations netcell_ops = {
-	.inherits	= &ata_bmdma_port_ops,
-	.cable_detect	= ata_cable_80wire,
-	.read_id	= netcell_read_id,
+	.inherits	= 	&ata_bmdma_port_ops,
+	.sff_exec_command = 	ata_sff_exec_command_nopost,
+	.cable_detect	= 	ata_cable_80wire,
+	.read_id	= 	netcell_read_id,
 };
 
 
drivers/ata/pata_ns87410.c +6 -5
index 2110863..205c3d2 100644
@@ -133,11 +133,12 @@ static struct scsi_host_template ns87410_sht = {
 };
 
 static struct ata_port_operations ns87410_port_ops = {
-	.inherits	= &ata_sff_port_ops,
-	.qc_issue	= ns87410_qc_issue,
-	.cable_detect	= ata_cable_40wire,
-	.set_piomode	= ns87410_set_piomode,
-	.prereset	= ns87410_pre_reset,
+	.inherits		= &ata_sff_port_ops,
+	.sff_exec_command	= ata_sff_exec_command_nopost,
+	.qc_issue		= ns87410_qc_issue,
+	.cable_detect		= ata_cable_40wire,
+	.set_piomode		= ns87410_set_piomode,
+	.prereset		= ns87410_pre_reset,
 };
 
 static int ns87410_init_one(struct pci_dev *dev, const struct pci_device_id *id)
drivers/ata/pata_ns87415.c +1 -0
index 830431f..ed46f57 100644
@@ -302,6 +302,7 @@ static u8 ns87560_bmdma_status(struct ata_port *ap)
 static struct ata_port_operations ns87415_pata_ops = {
 	.inherits		= &ata_bmdma_port_ops,
 
+	.sff_exec_command	= ata_sff_exec_command_nopost,
 	.check_atapi_dma	= ns87415_check_atapi_dma,
 	.bmdma_setup		= ns87415_bmdma_setup,
 	.bmdma_start		= ns87415_bmdma_start,
drivers/ata/pata_oldpiix.c +1 -0
index 5f6aba7..1fd531a 100644
@@ -210,6 +210,7 @@ static struct scsi_host_template oldpiix_sht = {
 
 static struct ata_port_operations oldpiix_pata_ops = {
 	.inherits		= &ata_bmdma_port_ops,
+	.sff_exec_command	= ata_sff_exec_command_nopost,
 	.qc_issue		= oldpiix_qc_issue,
 	.cable_detect		= ata_cable_40wire,
 	.set_piomode		= oldpiix_set_piomode,
drivers/ata/pata_opti.c +5 -4
index 00c5a02..f2dedbb 100644
@@ -153,10 +153,11 @@ static struct scsi_host_template opti_sht = {
 };
 
 static struct ata_port_operations opti_port_ops = {
-	.inherits	= &ata_sff_port_ops,
-	.cable_detect	= ata_cable_40wire,
-	.set_piomode	= opti_set_piomode,
-	.prereset	= opti_pre_reset,
+	.inherits		= &ata_sff_port_ops,
+	.sff_exec_command	= ata_sff_exec_command_nopost,
+	.cable_detect		= ata_cable_40wire,
+	.set_piomode		= opti_set_piomode,
+	.prereset		= opti_pre_reset,
 };
 
 static int opti_init_one(struct pci_dev *dev, const struct pci_device_id *id)
drivers/ata/pata_optidma.c +10 -9
index 76b7d12..58d32f2 100644
@@ -338,18 +338,19 @@ static struct scsi_host_template optidma_sht = {
 };
 
 static struct ata_port_operations optidma_port_ops = {
-	.inherits	= &ata_bmdma_port_ops,
-	.cable_detect	= ata_cable_40wire,
-	.set_piomode	= optidma_set_pio_mode,
-	.set_dmamode	= optidma_set_dma_mode,
-	.set_mode	= optidma_set_mode,
-	.prereset	= optidma_pre_reset,
+	.inherits		= &ata_bmdma_port_ops,
+	.sff_exec_command	= ata_sff_exec_command_nopost,
+	.cable_detect		= ata_cable_40wire,
+	.set_piomode		= optidma_set_pio_mode,
+	.set_dmamode		= optidma_set_dma_mode,
+	.set_mode		= optidma_set_mode,
+	.prereset		= optidma_pre_reset,
 };
 
 static struct ata_port_operations optiplus_port_ops = {
-	.inherits	= &optidma_port_ops,
-	.set_piomode	= optiplus_set_pio_mode,
-	.set_dmamode	= optiplus_set_dma_mode,
+	.inherits		= &optidma_port_ops,
+	.set_piomode		= optiplus_set_pio_mode,
+	.set_dmamode		= optiplus_set_dma_mode,
 };
 
 /**
drivers/ata/pata_pcmcia.c +10 -9
index ac8d78d..ea73245 100644
@@ -154,18 +154,19 @@ static struct scsi_host_template pcmcia_sht = {
 };
 
 static struct ata_port_operations pcmcia_port_ops = {
-	.inherits	= &ata_sff_port_ops,
-	.sff_data_xfer	= ata_sff_data_xfer_noirq,
-	.cable_detect	= ata_cable_40wire,
-	.set_mode	= pcmcia_set_mode,
+	.inherits		= &ata_sff_port_ops,
+	.sff_exec_command	= ata_sff_exec_command_nopost,
+	.sff_data_xfer		= ata_sff_data_xfer_noirq,
+	.cable_detect		= ata_cable_40wire,
+	.set_mode		= pcmcia_set_mode,
 };
 
 static struct ata_port_operations pcmcia_8bit_port_ops = {
-	.inherits	= &ata_sff_port_ops,
-	.sff_data_xfer	= ata_data_xfer_8bit,
-	.cable_detect	= ata_cable_40wire,
-	.set_mode	= pcmcia_set_mode_8bit,
-	.drain_fifo	= pcmcia_8bit_drain_fifo,
+	.inherits		= &ata_sff_port_ops,
+	.sff_data_xfer		= ata_data_xfer_8bit,
+	.cable_detect		= ata_cable_40wire,
+	.set_mode		= pcmcia_set_mode_8bit,
+	.drain_fifo		= pcmcia_8bit_drain_fifo,
 };
 
 
drivers/ata/pata_pdc202xx_old.c +1 -0
index 9ac0897..0731e90 100644
@@ -277,6 +277,7 @@ static struct scsi_host_template pdc202xx_sht = {
 static struct ata_port_operations pdc2024x_port_ops = {
 	.inherits		= &ata_bmdma_port_ops,
 
+	.sff_exec_command	= ata_sff_exec_command_nopost,
 	.cable_detect		= ata_cable_40wire,
 	.set_piomode		= pdc202xx_set_piomode,
 	.set_dmamode		= pdc202xx_set_dmamode,
drivers/ata/pata_piccolo.c +5 -4
index 9816154..05c85a8 100644
@@ -68,10 +68,11 @@ static struct scsi_host_template tosh_sht = {
 };
 
 static struct ata_port_operations tosh_port_ops = {
-	.inherits	= &ata_bmdma_port_ops,
-	.cable_detect	= ata_cable_unknown,
-	.set_piomode	= tosh_set_piomode,
-	.set_dmamode	= tosh_set_dmamode
+	.inherits		= &ata_bmdma_port_ops,
+	.sff_exec_command	= ata_sff_exec_command_nopost,
+	.cable_detect		= ata_cable_unknown,
+	.set_piomode		= tosh_set_piomode,
+	.set_dmamode		= tosh_set_dmamode
 };
 
 /**
drivers/ata/pata_qdi.c +8 -7
index 45879dc..c9a468c 100644
@@ -158,16 +158,17 @@ static struct scsi_host_template qdi_sht = {
 };
 
 static struct ata_port_operations qdi6500_port_ops = {
-	.inherits	= &ata_sff_port_ops,
-	.qc_issue	= qdi_qc_issue,
-	.sff_data_xfer	= qdi_data_xfer,
-	.cable_detect	= ata_cable_40wire,
-	.set_piomode	= qdi6500_set_piomode,
+	.inherits	= 	&ata_sff_port_ops,
+	.sff_exec_command	= ata_sff_exec_command_nopost,
+	.qc_issue	= 	qdi_qc_issue,
+	.sff_data_xfer	= 	qdi_data_xfer,
+	.cable_detect	= 	ata_cable_40wire,
+	.set_piomode	= 	qdi6500_set_piomode,
 };
 
 static struct ata_port_operations qdi6580_port_ops = {
-	.inherits	= &qdi6500_port_ops,
-	.set_piomode	= qdi6580_set_piomode,
+	.inherits	= 	&qdi6500_port_ops,
+	.set_piomode	= 	qdi6580_set_piomode,
 };
 
 /**
drivers/ata/pata_radisys.c +1 -0
index fc96022..c376682 100644
@@ -189,6 +189,7 @@ static struct scsi_host_template radisys_sht = {
 
 static struct ata_port_operations radisys_pata_ops = {
 	.inherits		= &ata_bmdma_port_ops,
+	.sff_exec_command	= ata_sff_exec_command_nopost,
 	.qc_issue		= radisys_qc_issue,
 	.cable_detect		= ata_cable_unknown,
 	.set_piomode		= radisys_set_piomode,
drivers/ata/pata_rdc.c +1 -0
index 37092cf..0f5de69 100644
@@ -275,6 +275,7 @@ static void rdc_set_dmamode(struct ata_port *ap, struct ata_device *adev)
 
 static struct ata_port_operations rdc_pata_ops = {
 	.inherits		= &ata_bmdma32_port_ops,
+	.sff_exec_command	= ata_sff_exec_command_nopost,
 	.cable_detect		= rdc_pata_cable_detect,
 	.set_piomode		= rdc_set_piomode,
 	.set_dmamode		= rdc_set_dmamode,
drivers/ata/pata_rz1000.c +4 -3
index 4a454a8..5f83a76 100644
@@ -55,9 +55,10 @@ static struct scsi_host_template rz1000_sht = {
 };
 
 static struct ata_port_operations rz1000_port_ops = {
-	.inherits	= &ata_sff_port_ops,
-	.cable_detect	= ata_cable_40wire,
-	.set_mode	= rz1000_set_mode,
+	.inherits		= &ata_sff_port_ops,
+	.cable_detect		= ata_cable_40wire,
+	.set_mode		= rz1000_set_mode,
+	.sff_exec_command	= ata_sff_exec_command_nopost,
 };
 
 static int rz1000_fifo_disable(struct pci_dev *pdev)
drivers/ata/pata_sc1200.c +8 -7
index dfecc6f..2cc3463 100644
@@ -208,13 +208,14 @@ static struct scsi_host_template sc1200_sht = {
 };
 
 static struct ata_port_operations sc1200_port_ops = {
-	.inherits	= &ata_bmdma_port_ops,
-	.qc_prep 	= ata_sff_dumb_qc_prep,
-	.qc_issue	= sc1200_qc_issue,
-	.qc_defer	= sc1200_qc_defer,
-	.cable_detect	= ata_cable_40wire,
-	.set_piomode	= sc1200_set_piomode,
-	.set_dmamode	= sc1200_set_dmamode,
+	.inherits		= &ata_bmdma_port_ops,
+	.sff_exec_command	= ata_sff_exec_command_nopost,
+	.qc_prep 		= ata_sff_dumb_qc_prep,
+	.qc_issue		= sc1200_qc_issue,
+	.qc_defer		= sc1200_qc_defer,
+	.cable_detect		= ata_cable_40wire,
+	.set_piomode		= sc1200_set_piomode,
+	.set_dmamode		= sc1200_set_dmamode,
 };
 
 /**
drivers/ata/pata_sch.c +1 -0
index 99cceb4..9a0c0e3 100644
@@ -77,6 +77,7 @@ static struct scsi_host_template sch_sht = {
 
 static struct ata_port_operations sch_pata_ops = {
 	.inherits		= &ata_bmdma_port_ops,
+	.sff_exec_command	= ata_sff_exec_command_nopost,
 	.cable_detect		= ata_cable_unknown,
 	.set_piomode		= sch_set_piomode,
 	.set_dmamode		= sch_set_dmamode,
drivers/ata/pata_serverworks.c +6 -5
index 9524d54..8745349 100644
@@ -301,11 +301,12 @@ static struct scsi_host_template serverworks_sht = {
 };
 
 static struct ata_port_operations serverworks_osb4_port_ops = {
-	.inherits	= &ata_bmdma_port_ops,
-	.cable_detect	= serverworks_cable_detect,
-	.mode_filter	= serverworks_osb4_filter,
-	.set_piomode	= serverworks_set_piomode,
-	.set_dmamode	= serverworks_set_dmamode,
+	.inherits		= &ata_bmdma_port_ops,
+	.sff_exec_command	= ata_sff_exec_command_nopost,
+	.cable_detect		= serverworks_cable_detect,
+	.mode_filter		= serverworks_osb4_filter,
+	.set_piomode		= serverworks_set_piomode,
+	.set_dmamode		= serverworks_set_dmamode,
 };
 
 static struct ata_port_operations serverworks_csb_port_ops = {
drivers/ata/pata_sis.c +2 -0
index b670803..aca9064 100644
@@ -505,6 +505,7 @@ static struct scsi_host_template sis_sht = {
 
 static struct ata_port_operations sis_133_for_sata_ops = {
 	.inherits		= &ata_bmdma_port_ops,
+	.sff_exec_command	= ata_sff_exec_command_nopost,
 	.set_piomode		= sis_133_set_piomode,
 	.set_dmamode		= sis_133_set_dmamode,
 	.cable_detect		= sis_133_cable_detect,
@@ -512,6 +513,7 @@ static struct ata_port_operations sis_133_for_sata_ops = {
 
 static struct ata_port_operations sis_base_ops = {
 	.inherits		= &ata_bmdma_port_ops,
+	.sff_exec_command	= ata_sff_exec_command_nopost,
 	.prereset		= sis_pre_reset,
 };
 
drivers/ata/pata_triflex.c +7 -6
index 48f5060..61520dc 100644
@@ -179,12 +179,13 @@ static struct scsi_host_template triflex_sht = {
 };
 
 static struct ata_port_operations triflex_port_ops = {
-	.inherits	= &ata_bmdma_port_ops,
-	.bmdma_start 	= triflex_bmdma_start,
-	.bmdma_stop	= triflex_bmdma_stop,
-	.cable_detect	= ata_cable_40wire,
-	.set_piomode	= triflex_set_piomode,
-	.prereset	= triflex_prereset,
+	.inherits		= &ata_bmdma_port_ops,
+	.sff_exec_command	= ata_sff_exec_command_nopost,
+	.bmdma_start 		= triflex_bmdma_start,
+	.bmdma_stop		= triflex_bmdma_stop,
+	.cable_detect		= ata_cable_40wire,
+	.set_piomode		= triflex_set_piomode,
+	.prereset		= triflex_prereset,
 };
 
 static int triflex_init_one(struct pci_dev *dev, const struct pci_device_id *id)
drivers/ata/pata_via.c +9 -8
index 87fb89e..bd65791 100644
@@ -440,14 +440,15 @@ static struct scsi_host_template via_sht = {
 };
 
 static struct ata_port_operations via_port_ops = {
-	.inherits	= &ata_bmdma_port_ops,
-	.cable_detect	= via_cable_detect,
-	.set_piomode	= via_set_piomode,
-	.set_dmamode	= via_set_dmamode,
-	.prereset	= via_pre_reset,
-	.sff_tf_load	= via_tf_load,
-	.port_start	= via_port_start,
-	.mode_filter	= via_mode_filter,
+	.inherits		= &ata_bmdma_port_ops,
+	.sff_exec_command	= ata_sff_exec_command_nopost,
+	.cable_detect		= via_cable_detect,
+	.set_piomode		= via_set_piomode,
+	.set_dmamode		= via_set_dmamode,
+	.prereset		= via_pre_reset,
+	.sff_tf_load		= via_tf_load,
+	.port_start		= via_port_start,
+	.mode_filter		= via_mode_filter,
 };
 
 static struct ata_port_operations via_port_ops_noirq = {
drivers/ata/pata_winbond.c +5 -4
index 6d8619b..066deea 100644
@@ -126,10 +126,11 @@ static struct scsi_host_template winbond_sht = {
 };
 
 static struct ata_port_operations winbond_port_ops = {
-	.inherits	= &ata_sff_port_ops,
-	.sff_data_xfer	= winbond_data_xfer,
-	.cable_detect	= ata_cable_40wire,
-	.set_piomode	= winbond_set_piomode,
+	.inherits	= 	&ata_sff_port_ops,
+	.sff_exec_command	= ata_sff_exec_command_nopost,
+	.sff_data_xfer	= 	winbond_data_xfer,
+	.cable_detect	= 	ata_cable_40wire,
+	.set_piomode	= 	winbond_set_piomode,
 };
 
 /**
include/linux/libata.h +2 -0
index 242eb26..c4811d9 100644
@@ -1592,6 +1592,8 @@ extern void ata_sff_tf_load(struct ata_port *ap, const struct ata_taskfile *tf);
 extern void ata_sff_tf_read(struct ata_port *ap, struct ata_taskfile *tf);
 extern void ata_sff_exec_command(struct ata_port *ap,
 				 const struct ata_taskfile *tf);
+extern void ata_sff_exec_command_nopost(struct ata_port *ap,
+				 const struct ata_taskfile *tf);
 extern unsigned int ata_sff_data_xfer(struct ata_device *dev,
 			unsigned char *buf, unsigned int buflen, int rw);
 extern unsigned int ata_sff_data_xfer32(struct ata_device *dev,
#6 lore raw

Re: [PATCH 2/3] libata: Remove excess command issue delays

Quoted 14 lines · Alan Cox

/**
+ * ata_sff_exec_command_nopost - issue ATA command to host controller
+ * @ap: port to which command is being issued
+ * @tf: ATA taskfile register set
+ *
+ * Issues ATA command, with proper synchronization with interrupt
+ * handler / other threads. This version of the helper does not protect
+ * against any delayed writes done by the underlying fabric, it must
+ * therefore not be used for MMIO devices unless the device handles
+ * the 400nS command delay stall internally.
+ *
+ * LOCKING:
+ * spin_lock_irqsave(host lock)
+ */

drivers/ata/libata-sff.c void ata_sff_exec_command(struct ata_port *ap, const struct ata_taskfile *tf) · line 702

Quoted 7 lines
drivers/ata/libata-sff.c +7 -0
+void ata_sff_exec_command_nopost(struct ata_port *ap,
+                                        const struct ata_taskfile *tf)
+{
+	DPRINTK("ata%u: cmd 0x%X\n", ap->print_id, tf->command);
+	iowrite8(tf->command, ap->ioaddr.command_addr);
+}
+EXPORT_SYMBOL_GPL(ata_sff_exec_command_nopost);

where did the 400ns delay go, for the 'nopost' version?

#7 lore raw

Re: [PATCH 2/3] libata: Remove excess command issue delays

Quoted 16 lines · On Fri, 14 May 2010 22:24:37 -0400 Jeff Garzik <[email protected]> wrote:
Quoted 15 lines · Alan Cox

/**
+ * ata_sff_exec_command_nopost - issue ATA command to host controller
+ * @ap: port to which command is being issued
+ * @tf: ATA taskfile register set
+ *
+ * Issues ATA command, with proper synchronization with interrupt
+ * handler / other threads. This version of the helper does not protect
+ * against any delayed writes done by the underlying fabric, it must
+ * therefore not be used for MMIO devices unless the device handles
+ * the 400nS command delay stall internally.
+ *
+ * LOCKING:
+ * spin_lock_irqsave(host lock)
+ */
+void ata_sff_exec_command_nopost(struct ata_port *ap,

Quoted 8 lines

drivers/ata/libata-sff.c void ata_sff_exec_command(struct ata_port *ap, const struct ata_taskfile *tf) · line 702

Quoted 6 lines
drivers/ata/libata-sff.c +6 -0
+                                        const struct ata_taskfile *tf)
+{
+	DPRINTK("ata%u: cmd 0x%X\n", ap->print_id, tf->command);
+	iowrite8(tf->command, ap->ioaddr.command_addr);
+}
+EXPORT_SYMBOL_GPL(ata_sff_exec_command_nopost);

where did the 400ns delay go, for the 'nopost' version?

Good question. It should indeed have an ndelay(400) after the iowrite8 I'll go fix that.

#8 lore raw

Re: [PATCH 2/3] libata: Remove excess command issue delays

Quoted 28 lines · Alan Cox
Quoted 16 lines · On Fri, 14 May 2010 22:24:37 -0400 Jeff Garzik<[email protected]> wrote:
Quoted 15 lines · Alan Cox
   /**

+ * ata_sff_exec_command_nopost - issue ATA command to host controller
+ * @ap: port to which command is being issued
+ * @tf: ATA taskfile register set
+ *
+ * Issues ATA command, with proper synchronization with interrupt
+ * handler / other threads. This version of the helper does not protect
+ * against any delayed writes done by the underlying fabric, it must
+ * therefore not be used for MMIO devices unless the device handles
+ * the 400nS command delay stall internally.
+ *
+ * LOCKING:
+ * spin_lock_irqsave(host lock)
+ */
+void ata_sff_exec_command_nopost(struct ata_port *ap,

Quoted 8 lines

drivers/ata/libata-sff.c void ata_sff_exec_command(struct ata_port *ap, const struct ata_taskfile *tf) · line 702

Quoted 6 lines
drivers/ata/libata-sff.c +6 -0
+                                        const struct ata_taskfile *tf)
+{
+	DPRINTK("ata%u: cmd 0x%X\n", ap->print_id, tf->command);
+	iowrite8(tf->command, ap->ioaddr.command_addr);
+}
+EXPORT_SYMBOL_GPL(ata_sff_exec_command_nopost);

where did the 400ns delay go, for the 'nopost' version?

Quoted 2 lines

Good question. It should indeed have an ndelay(400) after the iowrite8 I'll go fix that.

No complaints if I go ahead and add that myself?

I'd like to go ahead and get it in.

Jeff

#9 lore raw

Re: [PATCH 2/3] libata: Remove excess command issue delays

In reply to Alan Cox
Quoted 28 lines · Alan Cox
Quoted 16 lines · On Fri, 14 May 2010 22:24:37 -0400 Jeff Garzik<[email protected]> wrote:
Quoted 15 lines · Alan Cox
   /**

+ * ata_sff_exec_command_nopost - issue ATA command to host controller
+ * @ap: port to which command is being issued
+ * @tf: ATA taskfile register set
+ *
+ * Issues ATA command, with proper synchronization with interrupt
+ * handler / other threads. This version of the helper does not protect
+ * against any delayed writes done by the underlying fabric, it must
+ * therefore not be used for MMIO devices unless the device handles
+ * the 400nS command delay stall internally.
+ *
+ * LOCKING:
+ * spin_lock_irqsave(host lock)
+ */
+void ata_sff_exec_command_nopost(struct ata_port *ap,

Quoted 8 lines

drivers/ata/libata-sff.c void ata_sff_exec_command(struct ata_port *ap, const struct ata_taskfile *tf) · line 702

Quoted 6 lines
drivers/ata/libata-sff.c +6 -0
+                                        const struct ata_taskfile *tf)
+{
+	DPRINTK("ata%u: cmd 0x%X\n", ap->print_id, tf->command);
+	iowrite8(tf->command, ap->ioaddr.command_addr);
+}
+EXPORT_SYMBOL_GPL(ata_sff_exec_command_nopost);

where did the 400ns delay go, for the 'nopost' version?

Quoted 2 lines

Good question. It should indeed have an ndelay(400) after the iowrite8 I'll go fix that.

Ping...

author
#10 lore raw

PATCH 3/3 libata: Make sil680 do its own exec_command posting

In reply to Alan Cox

Use our own mmio area to avoid PCI posting. This avoids the rather slow paranoid implementation in the default handler.

---

 drivers/ata/pata_sil680.c |   30 ++++++++++++++++++++++++++----
 1 files changed, 26 insertions(+), 4 deletions(-)
drivers/ata/pata_sil680.c +26 -4
index c6c589c..43faf10 100644
@@ -190,15 +190,37 @@ static void sil680_set_dmamode(struct ata_port *ap, struct ata_device *adev)
 	pci_write_config_word(pdev, ua, ultra);
 }
 
+/**
+ *	sil680_sff_exec_command - issue ATA command to host controller
+ *	@ap: port to which command is being issued
+ *	@tf: ATA taskfile register set
+ *
+ *	Issues ATA command, with proper synchronization with interrupt
+ *	handler / other threads. Use our MMIO space for PCI posting to avoid
+ *	a hideously slow cycle all the way to the device.
+ *
+ *	LOCKING:
+ *	spin_lock_irqsave(host lock)
+ */
+void sil680_sff_exec_command(struct ata_port *ap,
+					const struct ata_taskfile *tf)
+{
+	DPRINTK("ata%u: cmd 0x%X\n", ap->print_id, tf->command);
+	iowrite8(tf->command, ap->ioaddr.command_addr);
+	ioread8(ap->ioaddr.bmdma_addr + ATA_DMA_CMD);
+}
+
 static struct scsi_host_template sil680_sht = {
 	ATA_BMDMA_SHT(DRV_NAME),
 };
 
+
 static struct ata_port_operations sil680_port_ops = {
-	.inherits	= &ata_bmdma32_port_ops,
-	.cable_detect	= sil680_cable_detect,
-	.set_piomode	= sil680_set_piomode,
-	.set_dmamode	= sil680_set_dmamode,
+	.inherits		= &ata_bmdma32_port_ops,
+	.sff_exec_command	= sil680_sff_exec_command,
+	.cable_detect		= sil680_cable_detect,
+	.set_piomode		= sil680_set_piomode,
+	.set_dmamode		= sil680_set_dmamode,
 };
 
 /**
Applied
#11 lore raw

Re: [PATCH 3/3] libata: Make sil680 do its own exec_command posting

Quoted 8 lines · Alan Cox

Use our own mmio area to avoid PCI posting. This avoids the rather slow paranoid implementation in the default handler.

---

  drivers/ata/pata_sil680.c |   30 ++++++++++++++++++++++++++----
  1 files changed, 26 insertions(+), 4 deletions(-)

applied