iw: fix makefile for cqm
RFC PATCH 1/3 iw: fix makefile for cqm
Signed-off-by Bruno Randolf <[email protected]>
--- Makefile | 2 +- 1 files changed, 1 insertions(+), 1 deletions(-)
Makefile +1 -1
@@ -17,7 +17,7 @@ CFLAGS += -Wall -Wundef -Wstrict-prototypes -Wno-trigraphs -fno-strict-aliasing OBJS = iw.o genl.o event.o info.o phy.o \ interface.o ibss.o station.o survey.o util.o \ mesh.o mpath.o scan.o reg.o version.o \ - reason.o status.o connect.o link.o offch.o ps.o cqm.c + reason.o status.o connect.o link.o offch.o ps.o cqm.o OBJS += sections.o ALL = iw
RFC PATCH 2/3 iw: sync nl80211.h with wireless-testing
adding AP isolate, set channel and antenna settings
Signed-off-by Bruno Randolf <[email protected]>
--- nl80211.h | 38 ++++++++++++++++++++++++++++++++++++++ 1 files changed, 38 insertions(+), 0 deletions(-)
nl80211.h +38 -0
@@ -52,6 +52,8 @@* %NL80211_ATTR_WIPHY_CHANNEL_TYPE, %NL80211_ATTR_WIPHY_RETRY_SHORT, * %NL80211_ATTR_WIPHY_RETRY_LONG, %NL80211_ATTR_WIPHY_FRAG_THRESHOLD, * and/or %NL80211_ATTR_WIPHY_RTS_THRESHOLD. +* However, for setting the channel, see %NL80211_CMD_SET_CHANNEL +* instead, the support here is for backward compatibility only. * @NL80211_CMD_NEW_WIPHY: Newly created wiphy, response to get request * or rename notification. Has attributes %NL80211_ATTR_WIPHY and * %NL80211_ATTR_WIPHY_NAME.
@@ -329,6 +331,18 @@* @NL80211_CMD_NOTIFY_CQM: Connection quality monitor notification. This * command is used as an event to indicate the that a trigger level was * reached. +* @NL80211_CMD_SET_CHANNEL: Set the channel (using %NL80211_ATTR_WIPHY_FREQ +* and %NL80211_ATTR_WIPHY_CHANNEL_TYPE) the given interface (identifed +* by %NL80211_ATTR_IFINDEX) shall operate on. +* In case multiple channels are supported by the device, the mechanism +* with which it switches channels is implementation-defined. +* When a monitor interface is given, it can only switch channel while +* no other interfaces are operating to avoid disturbing the operation +* of any other interfaces, and other interfaces will again take +* precedence when they are used. +* +* @NL80211_CMD_SET_ANTENNA: Set a bitmap of antennas to use. +* @NL80211_CMD_GET_ANTENNA: Get antenna configuration from driver. * * @NL80211_CMD_MAX: highest used command number * @__NL80211_CMD_AFTER_LAST: internal use
@@ -428,6 +442,11 @@ enum nl80211_commands {NL80211_CMD_SET_CQM ,NL80211_CMD_NOTIFY_CQM , +NL80211_CMD_SET_CHANNEL , + +NL80211_CMD_SET_ANTENNA , +NL80211_CMD_GET_ANTENNA , +/* add new commands above here */ /* used to define NL80211_CMD_MAX below */
@@ -703,6 +722,18 @@ enum nl80211_commands {* @NL80211_ATTR_CQM: connection quality monitor configuration in a * nested attribute with %NL80211_ATTR_CQM_* sub-attributes. * +* @NL80211_ATTR_LOCAL_STATE_CHANGE: Flag attribute to indicate that a command +* is requesting a local authentication/association state change without +* invoking actual management frame exchange. This can be used with +* NL80211_CMD_AUTHENTICATE, NL80211_CMD_DEAUTHENTICATE, +* NL80211_CMD_DISASSOCIATE. +* +* @NL80211_ATTR_AP_ISOLATE: (AP mode) Do not forward traffic between stations +* connected to this BSS. +* +* @NL80211_ATTR_ANTENNA_TX: Bitmap of antennas to use for transmitting. +* @NL80211_ATTR_ANTENNA_RX: Bitmap of antennas to use for receiving. +* * @NL80211_ATTR_MAX: highest attribute number currently defined * @__NL80211_ATTR_AFTER_LAST: internal use */
@@ -856,6 +887,13 @@ enum nl80211_attrs {NL80211_ATTR_CQM , +NL80211_ATTR_LOCAL_STATE_CHANGE , + +NL80211_ATTR_AP_ISOLATE , + +NL80211_ATTR_ANTENNA_TX , +NL80211_ATTR_ANTENNA_RX , +/* add attributes here, update the policy in nl80211.c */ __NL80211_ATTR_AFTER_LAST,
RFC PATCH 3/3 iw: Add antenna set/get
In reply to Bruno RandolfAdd commands to set and get the antenna configuration. The antenna configuration is defined as a bitmap of 8 antennas. When multiple antennas are selected the driver may use diversity. Also the driver may reject antenna configurations it cannot support.
Signed-off-by Bruno Randolf <[email protected]>
--- Makefile | 2 + antenna.c | 92 +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ 2 files changed, 93 insertions(+), 1 deletions(-) create mode 100644 antenna.c
Makefile +1 -1
@@ -17,7 +17,7 @@ CFLAGS += -Wall -Wundef -Wstrict-prototypes -Wno-trigraphs -fno-strict-aliasing OBJS = iw.o genl.o event.o info.o phy.o \ interface.o ibss.o station.o survey.o util.o \ mesh.o mpath.o scan.o reg.o version.o \ - reason.o status.o connect.o link.o offch.o ps.o cqm.o + reason.o status.o connect.o link.o offch.o ps.o cqm.o antenna.o OBJS += sections.o ALL = iw
antenna.c new file +92 -0
92 lines not on this page · raw message