iw antenna command
cover iw antenna command
here the iw part. the option parsing is more flexible now and i added a possibility to use
iw phy0 anenna set X
to set both RX and TX antennas
+ one small fix for the channel command name
bruno
---
Bruno Randolf (3):
iw: add channel command name
iw: sync nl80211.h with wireless-testing
iw: Add antenna set/get
Makefile | 2 + antenna.c | 88 +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ nl80211.h | 12 ++++++++ util.c | 3 ++ 4 files changed, 104 insertions(+), 1 deletions(-) create mode 100644 antenna.c
Signature · 1 line
Signature
PATCH 1/3 iw: add channel command name
--- util.c | 1 + 1 files changed, 1 insertions(+), 0 deletions(-)
util.c +1 -0
@@ -165,6 +165,7 @@ static const char *commands[NL80211_CMD_MAX + 1] = { [NL80211_CMD_SET_TX_BITRATE_MASK] = "set_tx_bitrate_mask", [NL80211_CMD_REGISTER_ACTION] = "register_action", [NL80211_CMD_ACTION] = "action", + [NL80211_CMD_SET_CHANNEL] = "set_channel", };static char cmdbuf[100 ];
PATCH 2/3 iw: sync nl80211.h with wireless-testing
In reply to Bruno Randolfadding antenna settings
--- nl80211.h | 12 ++++++++++++ 1 files changed, 12 insertions(+), 0 deletions(-)
nl80211.h +12 -0
@@ -341,6 +341,9 @@* of any other interfaces, and other interfaces will again take * precedence when they are used. * +* @NL80211_CMD_SET_ANTENNA: Set a bitmap of antennas to use. +* @NL80211_CMD_GET_ANTENNA: Get antenna configuration from driver. +* * @NL80211_CMD_MAX: highest used command number * @__NL80211_CMD_AFTER_LAST: internal use */
@@ -441,6 +444,9 @@ enum nl80211_commands {NL80211_CMD_SET_CHANNEL , +NL80211_CMD_SET_ANTENNA , + NL80211_CMD_GET_ANTENNA, +/* add new commands above here */ /* used to define NL80211_CMD_MAX below */
@@ -725,6 +731,9 @@ enum nl80211_commands {* @NL80211_ATTR_AP_ISOLATE: (AP mode) Do not forward traffic between stations * connected to this BSS. * +* @NL80211_ATTR_ANTENNA_TX: Bitmap of antennas to use for transmitting. +* @NL80211_ATTR_ANTENNA_RX: Bitmap of antennas to use for receiving. +* * @NL80211_ATTR_MAX: highest attribute number currently defined * @__NL80211_ATTR_AFTER_LAST: internal use */
@@ -882,6 +891,9 @@ enum nl80211_attrs {NL80211_ATTR_AP_ISOLATE , +NL80211_ATTR_ANTENNA_TX , +NL80211_ATTR_ANTENNA_RX , +/* add attributes here, update the policy in nl80211.c */ __NL80211_ATTR_AFTER_LAST,
PATCH 3/3 iw: Add antenna set/get
In reply to Bruno RandolfAdd commands to set and get the antenna configuration. The antenna configuration is defined as a bitmap of 8 antennas. When multiple antennas are selected the driver may use diversity. Also the driver may reject antenna configurations it cannot support.
--- Makefile | 2 + antenna.c | 88 +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ util.c | 2 + 3 files changed, 91 insertions(+), 1 deletions(-) create mode 100644 antenna.c
Makefile +1 -1
@@ -17,7 +17,7 @@ CFLAGS += -Wall -Wundef -Wstrict-prototypes -Wno-trigraphs -fno-strict-aliasing OBJS = iw.o genl.o event.o info.o phy.o \ interface.o ibss.o station.o survey.o util.o \ mesh.o mpath.o scan.o reg.o version.o \ - reason.o status.o connect.o link.o offch.o ps.o cqm.o + reason.o status.o connect.o link.o offch.o ps.o cqm.o antenna.o OBJS += sections.o ALL = iw
antenna.c new file +88 -0
88 lines not on this page · raw message
util.c +2 -0
@@ -166,6 +166,8 @@ static const char *commands[NL80211_CMD_MAX + 1] = { [NL80211_CMD_REGISTER_ACTION] = "register_action", [NL80211_CMD_ACTION] = "action", [NL80211_CMD_SET_CHANNEL] = "set_channel", + [NL80211_CMD_SET_ANTENNA] = "antenna_set", + [NL80211_CMD_GET_ANTENNA] = "antenna_get", };static char cmdbuf[100 ];