Fix hang trying to protect flash sectors
cover Fix hang trying to protect flash sectors
Our hardware has part of the flash mapped in two address ranges. The CONFIG_SYS_MONITOR_BASE is in the upper 'boot' area, whereas the CONFIG_SYS_FLASH_BANKS_LIST has the full flash available at a lower address.
This all works fine until the code in cfi_flash.c:flash_init(), which uses flash_get_info() to find the flash_info_t associated with the monitor and environment. These are not in the probed flash range, so flash_get_info() returns NULL. This is not checked and is passed directly to flash_protect(). Since flash_protect() was not checking for this NULL pointer either, random memory would be clobbered causing the device to lock up.
This patch changes flash_protect() to check for the NULL, and the error goes unreported.
Mark Tomlinson (1):
flash: Check info pointer in flash_protect().
common/flash.c | 10 +++++++--- 1 files changed, 7 insertions(+), 3 deletions(-)
NOTICE: This message contains privileged and confidential information intended only for the use of the addressee named above. If you are not the intended recipient of this message you are hereby notified that you must not disseminate, copy or take any action in reliance on it. If you have received this message in error please notify Allied Telesis Labs Ltd immediately.
Any views expressed in this message are those of the individual sender, except where the sender has the authority to issue and specifically states them to be the views of Allied Telesis Labs.
PATCH 1/1 flash: Check info pointer in flash_protect().
Some calls to flash_protect() do not check that info is not NULL. This change prevents this from causing random memory to be stomped on.
--- common/flash.c | 10 +++++++--- 1 files changed, 7 insertions(+), 3 deletions(-)
common/flash.c +7 -3
@@ -43,15 +43,19 @@ extern flash_info_t flash_info[]; /* info for FLASH chips */void flash_protect (int flag,ulong from,ulong to,flash_info_t *info) { -ulong b_end = info->start[0 ] + info->size -1 ;/* bank end address */ -short s_end = info->sector_count -1 ;/* index of last sector */ +ulong b_end;/* bank end address */ +short s_end;/* index of last sector */ int i;/* Do nothing if input data is bad. */ -if (info->sector_count ==0 || info->size ==0 || to < from) { +if (!info || info->sector_count ==0 || info->size ==0 || + to < from) {return ; } + b_end = info->start[0 ] + info->size -1 ; + s_end = info->sector_count -1 ; + debug ("flash_protect %s: from 0x%08lX to 0x%08lX\n", (flag & FLAG_PROTECT_SET) ? "ON" : (flag & FLAG_PROTECT_CLEAR) ? "OFF" : "???",
Signature · 14 lines
1.6.3 NOTICE: This message contains privileged and confidential information intended only for the use of the addressee named above. If you are not the intended recipient of this message you are hereby notified that you must not disseminate, copy or take any action in reliance on it. If you have received this message in error please notify Allied Telesis Labs Ltd immediately. Any views expressed in this message are those of the individual sender, except where the sender has the authority to issue and specifically states them to be the views of Allied Telesis Labs.
PATCH 1/1 flash: Check info pointer in flash_protect().
Quoted 4 lines · On Tuesday 18 May 2010 01:26:35 Mark Tomlinson wrote:
Some calls to
flash_protect()do not check that info is not NULL. This change prevents this from causing random memory to be stomped on.
---
any patches need a s-o-b tag before they'll be accepted
Quoted 1 line
NOTICE: This message contains privileged and confidential
this junk has no business being on an open source mailing list
-mike
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 836 bytes
Desc: This is a digitally signed message part.
Url : http://lists.denx.de/pipermail/u-boot/attachments/20100519/9283fcc0/attachment.pgp
PATCH 1/1 flash: Check info pointer in flash_protect().
In reply to Mark TomlinsonDear Mark Tomlinson,
Quoted 3 lines · In message <1274160395-9308-2-git-send-email-mark.tomlinson@alliedtelesis.co.nz…
Some calls to
flash_protect()do not check that info is not NULL. This change prevents this from causing random memory to be stomped on.
When exactly would that be the case?
Quoted 3 lines
NOTICE: This message contains privileged and confidential information intended only for the use of the addressee named above. If you are not the intended recipient of
...
Such terms are obviously unacceptable for any code that is supposed to go into mainline.
Best regards,
Wolfgang Denk
Signature · 5 lines
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
The C-shell doesn't parse. It adhoculates.
- Casper.Dik at Holland.Sun.COM in <[email protected]>cover Fix hang trying to protect flash sectors
In reply to Mark TomlinsonHi Mark,
Quoted 4 lines · On Tuesday 18 May 2010 07:26:34 Mark Tomlinson wrote:
Our hardware has part of the flash mapped in two address ranges. The
CONFIG_SYS_MONITOR_BASEis in the upper 'boot' area, whereas theCONFIG_SYS_FLASH_BANKS_LISThas the full flash available at a lower address.
Just to be sure: You have 2 FLASH chips? Mapped at which addresses? And where does CONFIG_SYS_MONITOR_BASE point to?
Quoted 4 lines
This all works fine until the code in cfi_flash.c:flash_init(), which uses
flash_get_info()to find theflash_info_tassociated with the monitor and environment. These are not in the probed flash range, soflash_get_info()returns NULL.
You mean that "flash_get_info(CONFIG_SYS_MONITOR_BASE)" returns NULL? Please explain again, why is this the case?
Quoted 7 lines
This is not checked and is passed
directly toflash_protect(). Sinceflash_protect()was not checking for this NULL pointer either, random memory would be clobbered causing the device to lock up.This patch changes
flash_protect()to check for the NULL, and the error goes unreported.
I would prefer to fix the real problem, that flash_get_info() returns NULL, instead.
Cheers,
Stefan
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-0 Fax: (+49)-8142-66989-80 Email: office at denx.de
cover Fix hang trying to protect flash sectors
Yes we do have 2 flash chips. Here's the mapping:
#define CONFIG_SYS_FLASH_BASE 0xf8000000 /* 2 chips*16M */
#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */
and in our config.mk file:
TEXT_BASE = 0xfff40000
This is the same flash chip as that at 0xf8000000, but remapped at reset by a CPLD to the high memory area too.
The conditional code in cfi_flash.c:
#if (CONFIG_SYS_MONITOR_BASE >= CONFIG_SYS_FLASH_BASE) && \
(!defined(CONFIG_MONITOR_IS_IN_RAM))
is therefore included since 0xfff40000 is greater than 0xf8000000, but flash_get_info(0xfff40000) returns NULL (as expected).
I understand that not passing NULL to flash_protect() would be a better idea, and there's nothing wrong with doing both. I was going to fix it in cfi_flash.c, but noticed that many other areas of code (in different flash.c files) do the same thing. In our own build, I have just removed the code that tries to protect the monitor area, and will use an auto-protect area instead to do the same job.
- Mark
Quoted 1 line
Quoted 1 line
Quoted 1 line
Stefan Roese <[email protected]> 5/18/2010 8:20 PM >>>
Hi Mark,
Quoted 4 lines · On Tuesday 18 May 2010 07:26:34 Mark Tomlinson wrote:
Our hardware has part of the flash mapped in two address ranges. The
CONFIG_SYS_MONITOR_BASEis in the upper 'boot' area, whereas theCONFIG_SYS_FLASH_BANKS_LISThas the full flash available at a lower address.
Just to be sure: You have 2 FLASH chips? Mapped at which addresses? And where does CONFIG_SYS_MONITOR_BASE point to?
Quoted 4 lines
This all works fine until the code in cfi_flash.c:flash_init(), which uses
flash_get_info()to find theflash_info_tassociated with the monitor and environment. These are not in the probed flash range, soflash_get_info()returns NULL.
You mean that "flash_get_info(CONFIG_SYS_MONITOR_BASE)" returns NULL? Please explain again, why is this the case?
Quoted 7 lines
This is not checked and is passed
directly toflash_protect(). Sinceflash_protect()was not checking for this NULL pointer either, random memory would be clobbered causing the device to lock up.This patch changes
flash_protect()to check for the NULL, and the error goes unreported.
I would prefer to fix the real problem, that flash_get_info() returns NULL, instead.
Cheers,
Stefan
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-0 Fax: (+49)-8142-66989-80 Email: office at denx.de
NOTICE: This message contains privileged and confidential information intended only for the use of the addressee named above. If you are not the intended recipient of this message you are hereby notified that you must not disseminate, copy or take any action in reliance on it. If you have received this message in error please notify Allied Telesis Labs Ltd immediately.
Any views expressed in this message are those of the individual sender, except where the sender has the authority to issue and specifically states them to be the views of Allied Telesis Labs.
cover Fix hang trying to protect flash sectors
Mark,
Quoted 3 lines · On Tuesday 18 May 2010 22:10:51 mark tomlinson wrote:
Yes we do have 2 flash chips. Here's the mapping:
#define
CONFIG_SYS_FLASH_BASE0xf8000000/* 2 chips*16M */
Hmmm. 2 * 16MByte, thats 32MByte == 0x2000000. So you should have one chip at base address 0xff000000 and one at 0xfe000000. Why 0xf8000000?
Quoted 7 lines
#define
CONFIG_SYS_MONITOR_BASETEXT_BASE/* start of monitor */and in our config.mk file:
TEXT_BASE=0xfff40000This is the same flash chip as that at
0xf8000000, but remapped at reset
by
Quoted 1 line
a CPLD to the high memory area too.
This seems wrong. See my comments above.
Quoted 5 lines
The conditional code in
cfi_flash.c:
#if (CONFIG_SYS_MONITOR_BASE>=CONFIG_SYS_FLASH_BASE) && \
(!defined(CONFIG_MONITOR_IS_IN_RAM))
is therefore included since0xfff40000is greater than0xf8000000, butflash_get_info(0xfff40000)returns NULL (as expected).
I don't see why flash_get_info(0xfff40000) should return NULL. It should return the pointer to the 16MB FLASH chip starting at 0xff000000.
Quoted 2 lines
I understand that not passing NULL to
flash_protect()would be a better idea, and there's nothing wrong with doing both.
Agreed in general. But we have to keep the code compact. And unnecessary checks do increase the code size (at least a small bit).
Quoted 5 lines
I was going to fix it in
cfi_flash.c, but noticed that many other areas of code (in differentflash.cfiles) do the same thing. In our own build, I have just removed the code that tries to protect the monitor area, and will use an auto-protect area instead to do the same job.
"auto-protect area"? Please explain what you mean with this? Perhaps this is an interesting "feature" for mainline as well.
Cheers,
Stefan
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-0 Fax: (+49)-8142-66989-80 Email: office at denx.de
cover Fix hang trying to protect flash sectors
Sorry, no. The flash chips are 0xf8000000-0xf9ffffff (32MB). (Actually we have twice this area reserved for 64MB flash in the future). The flash chip from 0xf8000000 is also mirrored at 0xfff00000 at boot time. I don't know if you consider this a hardware bug to not have all the flash at the very top of memory, but that is the way our product has been designed. Here's a memory map of the high memory area:
f8000000-fbffffff 64M Flash
fe000000-fe0fffff 1M Battery-backed RAM
ff000000-ff00ffff 64K On-board logic
ff700000-ff7fffff 1M CCSR
fff00000-ffffffff 1M Flash (mirror of f8000000).
So we have CONFIG_SYS_FLASH_BASE pointing to the entire Flash, and CONFIG_SYS_MONITOR_BASE pointing to the mirrored section which contains u-boot.
The auto protect was already there; nothing new. See CONFIG_SYS_FLASH_AUTOPROTECT_LIST in cfi_flash.c.
Quoted 1 line
Quoted 1 line
Quoted 1 line
Stefan Roese <[email protected]> 5/19/2010 9:44 PM >>>
Mark,
Quoted 3 lines · On Tuesday 18 May 2010 22:10:51 mark tomlinson wrote:
Yes we do have 2 flash chips. Here's the mapping:
#define
CONFIG_SYS_FLASH_BASE0xf8000000/* 2 chips*16M */
Hmmm. 2 * 16MByte, thats 32MByte == 0x2000000. So you should have one chip at base address 0xff000000 and one at 0xfe000000. Why 0xf8000000?
Quoted 7 lines
#define
CONFIG_SYS_MONITOR_BASETEXT_BASE/* start of monitor */and in our config.mk file:
TEXT_BASE=0xfff40000This is the same flash chip as that at
0xf8000000, but remapped at reset
by
Quoted 1 line
a CPLD to the high memory area too.
This seems wrong. See my comments above.
Quoted 5 lines
The conditional code in
cfi_flash.c:
#if (CONFIG_SYS_MONITOR_BASE>=CONFIG_SYS_FLASH_BASE) && \
(!defined(CONFIG_MONITOR_IS_IN_RAM))
is therefore included since0xfff40000is greater than0xf8000000, butflash_get_info(0xfff40000)returns NULL (as expected).
I don't see why flash_get_info(0xfff40000) should return NULL. It should return the pointer to the 16MB FLASH chip starting at 0xff000000.
Quoted 2 lines
I understand that not passing NULL to
flash_protect()would be a better idea, and there's nothing wrong with doing both.
Agreed in general. But we have to keep the code compact. And unnecessary checks do increase the code size (at least a small bit).
Quoted 5 lines
I was going to fix it in
cfi_flash.c, but noticed that many other areas of code (in differentflash.cfiles) do the same thing. In our own build, I have just removed the code that tries to protect the monitor area, and will use an auto-protect area instead to do the same job.
"auto-protect area"? Please explain what you mean with this? Perhaps this is an interesting "feature" for mainline as well.
Cheers,
Stefan
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-0 Fax: (+49)-8142-66989-80 Email: office at denx.de
NOTICE: This message contains privileged and confidential information intended only for the use of the addressee named above. If you are not the intended recipient of this message you are hereby notified that you must not disseminate, copy or take any action in reliance on it. If you have received this message in error please notify Allied Telesis Labs Ltd immediately.
Any views expressed in this message are those of the individual sender, except where the sender has the authority to issue and specifically states them to be the views of Allied Telesis Labs.
cover Fix hang trying to protect flash sectors
Dear "mark tomlinson",
Please restrict your line length to some 70 characters or so, and stop posting HTML!
Quoted 7 lines · In message <[email protected]> you wrote:
Sorry, no. The flash chips are 0xf8000000-0xf9ffffff (32MB). (Actually we
have twice this area reserved for 64MB flash in the future). The flash chip from0xf8000000is also mirrored at0xfff00000at boot time. I do
n't know if you consider this a hardware bug to not have all the flash at
the very top of memory, but that is the way our product has been desig
ned. Here's a memory map of the high memory area:
It's not a hardware bug, but a configuration error.
Quoted 5 lines
f8000000-fbffffff 64M Flash
fe000000-fe0fffff 1M Battery-backed RAM
ff000000-ff00ffff 64K On-board logic
ff700000-ff7fffff 1M CCSR
fff00000-ffffffff 1M Flash (mirror off8000000).
This makes no sense. Fix your memory map, and map the flash (all of it) to the end of the address space.
Quoted 2 lines
So we have
CONFIG_SYS_FLASH_BASEpointing to the entire Flash, and CONFIG_SYS_MONITOR_BASEpointing to the mirrored section which contains u-boot.
As I mentioned above: misconigured.
Quoted 2 lines
NOTICE: This message contains privileged and confidential information intended only for the use of the addressee
...
And please stop posting these silly disclaimers.
Best regards,
Wolfgang Denk
Signature · 5 lines
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de Insufficient facts always invite danger. -- Spock, "Space Seed", stardate 3141.9
cover Fix hang trying to protect flash sectors
Disclaimer: I'm workmate of Mark's
Quoted 11 lines · Wolfgang Denk <wd <at> denx.de> writes:
It's not a hardware bug, but a configuration error.
Quoted 5 lines
f8000000-fbffffff 64M Flash
fe000000-fe0fffff 1M Battery-backed RAM
ff000000-ff00ffff 64K On-board logic
ff700000-ff7fffff 1M CCSR
fff00000-ffffffff 1M Flash (mirror off8000000).This makes no sense. Fix your memory map, and map the flash (all of it) to the end of the address space.
While it would be possible to shuffle the memory map around there is one problem with the hardware design that I don't think can be overcome (I'd love to be proven wrong). The boot chip select is mapped to the _bottom_ of the first flash chip. It was done this way so that we could expand the flash in the future as a rolling production change (we're now shipping units with 64MB fitted). i.e. we knew we could rely on a fixed base address so thats where we pointed the boot chip select.
I think in hindsight we could have modified our flash detection code to start at the top and jump backwards looking for extra chips. Unfortunately we're not able to change the hardware design for this product but we can take this into account on future designs.
Quoted 6 lines
Quoted 2 lines
NOTICE: This message contains privileged and confidential information intended only for the use of the addressee
...
And please stop posting these silly disclaimers.
Corporate overlords have been flogged :). General response has been to go sign up to gmail. Trust me it annoys us as much as it annoys you.
- C
cover Fix hang trying to protect flash sectors
Dear Chris Packham,
Quoted 8 lines · In message <[email protected]> you wrote:
While it would be possible to shuffle the memory map around there is one problem with the hardware design that I don't think can be overcome (I'd love to be proven wrong). The boot chip select is mapped to the _bottom_ of the first flash chip. It was done this way so that we could expand the flash in the future as a rolling production change (we're now shipping units with 64MB fitted). i.e. we knew we could rely on a fixed base address so thats where we pointed the boot chip select.
I don't see why this should be relevant. Usually you can set up nearly any memory map in software, independent of the CPU state at boot time.
Which exact processor family are we talking about?
Quoted 2 lines
I think in hindsight we could have modified our flash detection code to start at the top and jump backwards looking for extra chips. Unfortunately
What do you mean by "our flash detection code"? Are you using any private code for that? Why? U-Boot already has all the needed stuff, just use it.
Quoted 2 lines
we're not able to change the hardware design for this product but we can take this into account on future designs.
I'm not convinced that any hardware changes would be needed.
Best regards,
Wolfgang Denk
Signature · 4 lines
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de Don't panic.
cover Fix hang trying to protect flash sectors
Hi Wolfgang,
Quoted 12 lines · Wolfgang Denk
Dear Chris Packham,
Quoted 8 lines · In message <[email protected]> you wrote:
While it would be possible to shuffle the memory map around there is one problem with the hardware design that I don't think can be overcome (I'd love to be proven wrong). The boot chip select is mapped to the _bottom_ of the first flash chip. It was done this way so that we could expand the flash in the future as a rolling production change (we're now shipping units with 64MB fitted). i.e. we knew we could rely on a fixed base address so thats where we pointed the boot chip select.
Quoted 4 lines
I don't see why this should be relevant. Usually you can set up nearly any memory map in software, independent of the CPU state at boot time.
Which exact processor family are we talking about?
Freescale MPC8541. CS0 is mapped by an external CPLD to either the bottom block of flash _or_ to a plug in card which has physical EPROMs which we use when we're bringing the board up. On newer designs we actually use pre-programmed flash chips in the factory and JTAG in circuit debuggers for development.
Quoted 7 lines
Quoted 2 lines
I think in hindsight we could have modified our flash detection code to start at the top and jump backwards looking for extra chips. Unfortunately
What do you mean by "our flash detection code"? Are you using any private code for that? Why? U-Boot already has all the needed stuff, just use it.
This design was originally done for a proprietary boot loader before we saw the light and switched to u-boot. That was what I meant by "our flash detection code".
Recently we've just switched to using the CFI driver in the latest u-boot version. Prior to this (based on version 1.1.4) we still had our own board/.../flash.c.
Quoted 4 lines
Quoted 2 lines
we're not able to change the hardware design for this product but we can take this into account on future designs.
I'm not convinced that any hardware changes would be needed.
I think we'd need 2 different boot loaders configurations, one for running from EPROM, one for running from flash.
If we ignore the EPROM it wouldn't be too hard to re-define the memory map such that we have flash arranged with the boot loader and environment in the bottom 1MB of the first flash chip with the file system in the top 31MB and optionally the second flash chip. The plug in EPROM card is still very useful when you accidentally brick your board so we'd still want to have that, which could be done easily with the existing configuration.
I'll look into shuffling the memory map around. It'd also be a good opportunity to start using the mtd maps in Linux.
- C