sata_sil: freeze on modprobe
I'm testing sata_sil with this controller:
00:0b.0 RAID bus controller: Silicon Image, Inc. SiI 3114 [SATALink/SATARaid] Serial ATA Controller (rev 02) 00:0b.0 0104: 1095:3114 (rev 02)
with two different hard disks. On modprobe there's an EH situation which freezes the task for several minutes. The device
node is not even created. The module device count is incremented to 3.
an echo 1 >rescan triggers the same situation again.
I'm running on 2.6.34.
how can I help debugging?
sata_sil 0000:00:0b.0: version 2.4sata_sil 0000:00:0b.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 sata_sil 0000:00:0b.0: Applying R_ERR on DMA activate FIS errata fix scsi4 : sata_sil
scsi5 : sata_sil
scsi6 : sata_sil
scsi7 : sata_sil
ata5: SATA max UDMA/100 mmio m1024@0xfde00000 tf 0xfde00080 irq 16
ata6: SATA max UDMA/100 mmio m1024@0xfde00000 tf 0xfde000c0 irq 16
ata7: SATA max UDMA/100 mmio m1024@0xfde00000 tf 0xfde00280 irq 16
ata8: SATA max UDMA/100 mmio m1024@0xfde00000 tf 0xfde002c0 irq 16
ata5: SATA link down (SStatus 0 SControl 310)
ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata6.00: ATA-8: WDC WD2502ABYS-18B7A0, 02.03B04, max UDMA/133
ata6.00: 488281250 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata6.00: applying Seagate errata fix (mod15write workaround)
ata6.00: configured for UDMA/100
scsi 5:0:0:0: Direct-Access ATA WDC WD2502ABYS-1 02.0 PQ: 0 ANSI: 5
sd 5:0:0:0: Attached scsi generic sg2 type 0
sd 5:0:0:0: [sdc] 488281250 512-byte logical blocks: (250 GB/232 GiB)
sd 5:0:0:0: [sdc] Write Protect is off
sd 5:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 5:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdc:
ata7: SATA link down (SStatus 0 SControl 310)
ata8: SATA link down (SStatus 0 SControl 310)
ata6: drained 65536 bytes to clear DRQ.
ata6.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata6.00: failed command: READ DMA
ata6.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata6.00: status: { DRDY }
ata6: hard resetting link
ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 310) ata6.00: configured for UDMA/100
ata6.00: device reported invalid CHS sector 0
ata6: EH complete
ata6: drained 65536 bytes to clear DRQ.
ata6.00: limiting speed to UDMA/66:PIO4
ata6.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen ata6.00: failed command: READ DMA
ata6.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata6.00: status: { DRDY }
ata6: hard resetting link
ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 310) ata6.00: configured for UDMA/66
ata6.00: device reported invalid CHS sector 0
ata6: EH complete
ata6: drained 65536 bytes to clear DRQ.
ata6.00: limiting speed to UDMA/33:PIO4
ata6.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen ata6.00: failed command: READ DMA
ata6.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata6.00: status: { DRDY }
ata6: hard resetting link
ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 310) ata6.00: configured for UDMA/33
ata6.00: device reported invalid CHS sector 0
ata6: EH complete
ata6: drained 65536 bytes to clear DRQ.
ata6.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen ata6.00: failed command: READ DMA
ata6.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata6.00: status: { DRDY }
ata6: hard resetting link
ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 310) ata6.00: configured for UDMA/33
ata6.00: device reported invalid CHS sector 0
ata6: EH complete
ata6: drained 65536 bytes to clear DRQ.
ata6.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen ata6.00: failed command: READ DMA
ata6.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata6.00: status: { DRDY }
ata6: hard resetting link
ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 310) ata6.00: configured for UDMA/33
ata6.00: device reported invalid CHS sector 0
ata6: EH complete
ata6: drained 65536 bytes to clear DRQ.
ata6.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen ata6.00: failed command: READ DMA
ata6.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata6.00: status: { DRDY }
ata6: hard resetting link
ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 310) ata6.00: configured for UDMA/33
ata6.00: device reported invalid CHS sector 0 sd 5:0:0:0: [sdc] Result: hostbyte=0x00 driverbyte=0x08 sd 5:0:0:0: [sdc] Sense Key : 0xb [current] [descriptor] Descriptor sense data with sense descriptors (in hex):
72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
00 00 00 00 sd 5:0:0:0: [sdc] ASC=0x0 ASCQ=0x0
sd 5:0:0:0: [sdc] CDB: cdb[0]=0x28: 28 00 00 00 00 00 00 00 08 00end_request: I/O error, dev sdc, sector 0
Buffer I/O error on device sdc, logical block 0
Buffer I/O error on device sdc, logical block 1
Buffer I/O error on device sdc, logical block 2
Buffer I/O error on device sdc, logical block 3
ata6: EH complete
ata6: drained 65536 bytes to clear DRQ.
ata6.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen ata6.00: failed command: READ DMA
ata6.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata6.00: status: { DRDY }
ata6: hard resetting link
ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 310) ata6.00: configured for UDMA/33
ata6.00: device reported invalid CHS sector 0
ata6: EH complete
ata6: drained 65536 bytes to clear DRQ.
ata6.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen ata6.00: failed command: READ DMA
ata6.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata6.00: status: { DRDY }
ata6: hard resetting link
ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 310) ata6.00: configured for UDMA/33
ata6.00: device reported invalid CHS sector 0
ata6: EH complete
ata6: drained 65536 bytes to clear DRQ.
ata6.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen ata6.00: failed command: READ DMA
ata6.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata6.00: status: { DRDY }
ata6: hard resetting link
ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 310) ata6.00: configured for UDMA/33
ata6.00: device reported invalid CHS sector 0
ata6: EH complete
ata6: drained 65536 bytes to clear DRQ.
ata6.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen ata6.00: failed command: READ DMA
ata6.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata6.00: status: { DRDY }
ata6: hard resetting link
ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 310) ata6.00: configured for UDMA/33
ata6.00: device reported invalid CHS sector 0
ata6: EH complete
ata6: drained 65536 bytes to clear DRQ.
ata6.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen ata6.00: failed command: READ DMA
ata6.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata6.00: status: { DRDY }
ata6: hard resetting link
ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 310) ata6.00: configured for UDMA/33
ata6.00: device reported invalid CHS sector 0
ata6: EH complete
ata6: drained 65536 bytes to clear DRQ.
ata6.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen ata6.00: failed command: READ DMA
ata6.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata6.00: status: { DRDY }
ata6: hard resetting link
ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 310) ata6.00: configured for UDMA/33
ata6.00: device reported invalid CHS sector 0 sd 5:0:0:0: [sdc] Result: hostbyte=0x00 driverbyte=0x08 sd 5:0:0:0: [sdc] Sense Key : 0xb [current] [descriptor] Descriptor sense data with sense descriptors (in hex):
72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
00 00 00 00 sd 5:0:0:0: [sdc] ASC=0x0 ASCQ=0x0
sd 5:0:0:0: [sdc] CDB: cdb[0]=0x28: 28 00 00 00 00 00 00 00 08 00end_request: I/O error, dev sdc, sector 0
Buffer I/O error on device sdc, logical block 0
Buffer I/O error on device sdc, logical block 1
Buffer I/O error on device sdc, logical block 2
Buffer I/O error on device sdc, logical block 3
unable to read partition table
ata6: EH complete
sdc: detected capacity change from 0 to 250000000000
sd 5:0:0:0: [sdc] Attached SCSI disk
sdc: detected capacity change from 0 to 250000000000
Signature · 6 lines
Best regards, Alessandro Zummo, Tower Technologies - Torino, Italy http://www.towertech.it
Quoted 10 lines · Alessandro Zummo
I'm testing
sata_silwith this controller:00:0b.0 RAID bus controller: Silicon Image, Inc. SiI 3114 [SATALink/SATARaid] Serial ATA Controller (rev 02) 00:0b.0 0104: 1095:3114 (rev 02)
with two different hard disks. On modprobe there's an EH situation which freezes the task for several minutes. The device node is not even created. The module device count is incremented to 3.
Quoted 5 lines
an echo 1>rescan triggers the same situation again.
I'm running on 2.6.34.
how can I help debugging?
What does /proc/interrupts show after this? It seems like you might be missing interrupts somehow.
Quoted 18 lines
sata_sil0000:00:0b.0: version 2.4sata_sil0000:00:0b.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16sata_sil0000:00:0b.0: ApplyingR_ERRon DMA activate FIS errata fix scsi4 :sata_sil
scsi5 :sata_sil
scsi6 :sata_sil
scsi7 :sata_sil
ata5: SATA max UDMA/100 mmio m1024@0xfde00000 tf0xfde00080irq 16
ata6: SATA max UDMA/100 mmio m1024@0xfde00000 tf0xfde000c0irq 16
ata7: SATA max UDMA/100 mmio m1024@0xfde00000 tf0xfde00280irq 16
ata8: SATA max UDMA/100 mmio m1024@0xfde00000 tf0xfde002c0irq 16
ata5: SATA link down (SStatus 0 SControl 310)
ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 310) ata6.00: ATA-8: WDC WD2502ABYS-18B7A0, 02.03B04, max UDMA/133 ata6.00: 488281250 sectors, multi 16: LBA48 NCQ (depth 0/32) ata6.00: applying Seagate errata fix (mod15write workaround)
This drive isn't in the mod15write blacklist - did you use the slow_down module parameter?
Quoted 174 lines
ata6.00: configured for UDMA/100
scsi 5:0:0:0: Direct-Access ATA WDC WD2502ABYS-1 02.0 PQ: 0 ANSI: 5
sd 5:0:0:0: Attached scsi generic sg2 type 0
sd 5:0:0:0: [sdc] 488281250 512-byte logical blocks: (250 GB/232 GiB)
sd 5:0:0:0: [sdc] Write Protect is off
sd 5:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 5:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdc:
ata7: SATA link down (SStatus 0 SControl 310)
ata8: SATA link down (SStatus 0 SControl 310)
ata6: drained 65536 bytes to clear DRQ.
ata6.00: exception Emask0x0SAct0x0SErr0x0action0x6frozen
ata6.00: failed command: READ DMA
ata6.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 inres 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)ata6.00: status: { DRDY }
ata6: hard resetting link
ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 310) ata6.00: configured for UDMA/100
ata6.00: device reported invalid CHS sector 0
ata6: EH complete
ata6: drained 65536 bytes to clear DRQ.
ata6.00: limiting speed to UDMA/66:PIO4
ata6.00: exception Emask0x0SAct0x0SErr0x0action0x6frozen ata6.00: failed command: READ DMA
ata6.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 inres 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)ata6.00: status: { DRDY }
ata6: hard resetting link
ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 310) ata6.00: configured for UDMA/66
ata6.00: device reported invalid CHS sector 0
ata6: EH complete
ata6: drained 65536 bytes to clear DRQ.
ata6.00: limiting speed to UDMA/33:PIO4
ata6.00: exception Emask0x0SAct0x0SErr0x0action0x6frozen ata6.00: failed command: READ DMA
ata6.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 inres 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)ata6.00: status: { DRDY }
ata6: hard resetting link
ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 310) ata6.00: configured for UDMA/33
ata6.00: device reported invalid CHS sector 0
ata6: EH complete
ata6: drained 65536 bytes to clear DRQ.
ata6.00: exception Emask0x0SAct0x0SErr0x0action0x6frozen ata6.00: failed command: READ DMA
ata6.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 inres 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)ata6.00: status: { DRDY }
ata6: hard resetting link
ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 310) ata6.00: configured for UDMA/33
ata6.00: device reported invalid CHS sector 0
ata6: EH complete
ata6: drained 65536 bytes to clear DRQ.
ata6.00: exception Emask0x0SAct0x0SErr0x0action0x6frozen ata6.00: failed command: READ DMA
ata6.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 inres 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)ata6.00: status: { DRDY }
ata6: hard resetting link
ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 310) ata6.00: configured for UDMA/33
ata6.00: device reported invalid CHS sector 0
ata6: EH complete
ata6: drained 65536 bytes to clear DRQ.
ata6.00: exception Emask0x0SAct0x0SErr0x0action0x6frozen ata6.00: failed command: READ DMA
ata6.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 inres 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)ata6.00: status: { DRDY }
ata6: hard resetting link
ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 310) ata6.00: configured for UDMA/33
ata6.00: device reported invalid CHS sector 0 sd 5:0:0:0: [sdc] Result: hostbyte=0x00 driverbyte=0x08 sd 5:0:0:0: [sdc] Sense Key :0xb[current] [descriptor] Descriptor sense data with sense descriptors (in hex):72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00 00 00 00 00sd 5:0:0:0: [sdc] ASC=0x0 ASCQ=0x0
sd 5:0:0:0: [sdc] CDB: cdb[0]=0x28: 28 00 00 00 00 00 00 00 08 00end_request: I/O error, dev sdc, sector 0
Buffer I/O error on device sdc, logical block 0
Buffer I/O error on device sdc, logical block 1
Buffer I/O error on device sdc, logical block 2
Buffer I/O error on device sdc, logical block 3
ata6: EH complete
ata6: drained 65536 bytes to clear DRQ.
ata6.00: exception Emask0x0SAct0x0SErr0x0action0x6frozen ata6.00: failed command: READ DMA
ata6.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 inres 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)ata6.00: status: { DRDY }
ata6: hard resetting link
ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 310) ata6.00: configured for UDMA/33
ata6.00: device reported invalid CHS sector 0
ata6: EH complete
ata6: drained 65536 bytes to clear DRQ.
ata6.00: exception Emask0x0SAct0x0SErr0x0action0x6frozen ata6.00: failed command: READ DMA
ata6.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 inres 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)ata6.00: status: { DRDY }
ata6: hard resetting link
ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 310) ata6.00: configured for UDMA/33
ata6.00: device reported invalid CHS sector 0
ata6: EH complete
ata6: drained 65536 bytes to clear DRQ.
ata6.00: exception Emask0x0SAct0x0SErr0x0action0x6frozen ata6.00: failed command: READ DMA
ata6.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 inres 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)ata6.00: status: { DRDY }
ata6: hard resetting link
ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 310) ata6.00: configured for UDMA/33
ata6.00: device reported invalid CHS sector 0
ata6: EH complete
ata6: drained 65536 bytes to clear DRQ.
ata6.00: exception Emask0x0SAct0x0SErr0x0action0x6frozen ata6.00: failed command: READ DMA
ata6.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 inres 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)ata6.00: status: { DRDY }
ata6: hard resetting link
ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 310) ata6.00: configured for UDMA/33
ata6.00: device reported invalid CHS sector 0
ata6: EH complete
ata6: drained 65536 bytes to clear DRQ.
ata6.00: exception Emask0x0SAct0x0SErr0x0action0x6frozen ata6.00: failed command: READ DMA
ata6.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 inres 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)ata6.00: status: { DRDY }
ata6: hard resetting link
ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 310) ata6.00: configured for UDMA/33
ata6.00: device reported invalid CHS sector 0
ata6: EH complete
ata6: drained 65536 bytes to clear DRQ.
ata6.00: exception Emask0x0SAct0x0SErr0x0action0x6frozen ata6.00: failed command: READ DMA
ata6.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 inres 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)ata6.00: status: { DRDY }
ata6: hard resetting link
ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 310) ata6.00: configured for UDMA/33
ata6.00: device reported invalid CHS sector 0 sd 5:0:0:0: [sdc] Result: hostbyte=0x00 driverbyte=0x08 sd 5:0:0:0: [sdc] Sense Key :0xb[current] [descriptor] Descriptor sense data with sense descriptors (in hex):72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00 00 00 00 00sd 5:0:0:0: [sdc] ASC=0x0 ASCQ=0x0
sd 5:0:0:0: [sdc] CDB: cdb[0]=0x28: 28 00 00 00 00 00 00 00 08 00end_request: I/O error, dev sdc, sector 0
Buffer I/O error on device sdc, logical block 0
Buffer I/O error on device sdc, logical block 1
Buffer I/O error on device sdc, logical block 2
Buffer I/O error on device sdc, logical block 3
unable to read partition table
ata6: EH complete
sdc: detected capacity change from 0 to 250000000000
sd 5:0:0:0: [sdc] Attached SCSI disk
sdc: detected capacity change from 0 to 250000000000
Quoted 4 lines · On Fri, 28 May 2010 17:55:43 -0600 Robert Hancock <[email protected]> wrote:
Quoted 1 line
how can I help debugging?
What does
/proc/interruptsshow after this? It seems like you might be missing interrupts somehow.
I think you've got it, IRQs are not flowing.
16: 6 IO-APIC-fasteoi sata_sil
I'll check the BIOS and twiggle around with
the slots.
Quoted 5 lines
Quoted 2 lines
ata6.00: 488281250 sectors, multi 16: LBA48 NCQ (depth 0/32) ata6.00: applying Seagate errata fix (mod15write workaround)
This drive isn't in the mod15write blacklist - did you use the
slow_downmodule parameter?
yes, i tried both with and without.
ty.
Signature · 6 lines
Best regards, Alessandro Zummo, Tower Technologies - Torino, Italy http://www.towertech.it