Linux kernel only reporting 16M / 128M
Greetings,
My flashing issues are now gone and will adress this later on.
Anyhow, I noticed that linux kernel only reports 16M total memory while the board got 128M. Was just wondering where to start looking? Everything works fine inside u-boot so its not passed correctly or something, not sure how the linux kernel detects that.
Any thoughts are helpful.
Best wishes
Kristoffer
Dear Kristoffer Ericson,
Quoted 2 lines · In message <20100609110742.GA1124@boggieman> you wrote:
My flashing issues are now gone and will adress this later on.
So the cause of the problems was the missing enabling of Vpp ?
Quoted 3 lines
Anyhow, I noticed that linux kernel only reports 16M total memory while the board got 128M. Was just wondering where to start looking? Everything works fine inside u-boot so its not passed correctly or something, not sure how the linux kernel detects that.
You RAM initialization in U-Boot seems to be broken. Check the number of rows/columns you program into your memory controller.
Best regards,
Wolfgang Denk
Signature · 4 lines
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de Weekends were made for programming. - Karl Lehenbauer
Quoted 8 lines · Wolfgang Denk
Dear Kristoffer Ericson,
Quoted 2 lines · In message <20100609110742.GA1124@boggieman> you wrote:
My flashing issues are now gone and will adress this later on.
So the cause of the problems was the missing enabling of Vpp ?
So it seems, works fine now.
Quoted 7 lines
Quoted 3 lines
Anyhow, I noticed that linux kernel only reports 16M total memory while the board got 128M. Was just wondering where to start looking? Everything works fine inside u-boot so its not passed correctly or something, not sure how the linux kernel detects that.
You RAM initialization in U-Boot seems to be broken. Check the number of rows/columns you program into your memory controller.
Hmm, will do that. However it seems to work fine in u-boot, I can see and access all memory. Also, the bootargs are not getting passed to the kernel, so might be same for memory tag?
Quoted 9 lines
Best regards,
Wolfgang Denk
Signature · 4 lines
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de Weekends were made for programming. - Karl Lehenbauer
Quoted 6 lines · Wolfgang Denk
Dear Kristoffer Ericson,
Quoted 2 lines · In message <20100609110742.GA1124@boggieman> you wrote:
My flashing issues are now gone and will adress this later on.
Quoted 8 lines
So the cause of the problems was the missing enabling of Vpp ?
Quoted 3 lines
Anyhow, I noticed that linux kernel only reports 16M total memory while the board got 128M. Was just wondering where to start looking? Everything works fine inside u-boot so its not passed correctly or something, not sure how the linux kernel detects that.
You RAM initialization in U-Boot seems to be broken. Check the number of rows/columns you program into your memory controller.
It works now, had missed exporting the bootparams adress in my board init. :)
Quoted 10 lines
Best regards,
Wolfgang Denk
Signature · 4 lines
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de Weekends were made for programming. - Karl Lehenbauer