omap mux updates for 2.6.36 merge window

index 8b3d269..76b5bf7 100644
@@ -43,6 +43,7 @@
 
 #define OMAP_MUX_BASE_OFFSET		0x30	/* Offset from CTRL_BASE */
 #define OMAP_MUX_BASE_SZ		0x5ca
+#define MUXABLE_GPIO_MODE3		BIT(0)
 
 struct omap_mux_entry {
 	struct omap_mux		mux;

@@ -51,6 +52,7 @@ struct omap_mux_entry {
 
 static unsigned long mux_phys;
 static void __iomem *mux_base;
+static u8 omap_mux_flags;
 
 u16 omap_mux_read(u16 reg)
 {

@@ -394,7 +396,10 @@ int __init omap_mux_init_gpio(int gpio, int val)
 
 			old_mode = omap_mux_read(m->reg_offset);
 			mux_mode = val & ~(OMAP_MUX_NR_MODES - 1);
-			mux_mode |= OMAP_MUX_MODE4;
+			if (omap_mux_flags & MUXABLE_GPIO_MODE3)
+				mux_mode |= OMAP_MUX_MODE3;
+			else
+				mux_mode |= OMAP_MUX_MODE4;
 			printk(KERN_DEBUG "mux: Setting signal "
 				"%s.gpio%i 0x%04x -> 0x%04x\n",
 				m->muxnames[0], gpio, old_mode, mux_mode);

@@ -1032,6 +1037,9 @@ int __init omap_mux_init(u32 mux_pbase, u32 mux_size,
 		return -ENODEV;
 	}
 
+	if (cpu_is_omap24xx())
+		omap_mux_flags = MUXABLE_GPIO_MODE3;
+
 	omap_mux_init_package(superset, package_subset, package_balls);
 	omap_mux_init_list(superset);
 	omap_mux_init_signals(board_mux);

index 480abc5..46315f2 100644
@@ -56,10 +56,12 @@
 
 /* Flags for omap_mux_init */
 #define OMAP_PACKAGE_MASK		0xffff
-#define OMAP_PACKAGE_CBP		4		/* 515-pin 0.40 0.50 */
-#define OMAP_PACKAGE_CUS		3		/* 423-pin 0.65 */
-#define OMAP_PACKAGE_CBB		2		/* 515-pin 0.40 0.50 */
-#define OMAP_PACKAGE_CBC		1		/* 515-pin 0.50 0.65 */
+#define OMAP_PACKAGE_CBP		6		/* 515-pin 0.40 0.50 */
+#define OMAP_PACKAGE_CUS		5		/* 423-pin 0.65 */
+#define OMAP_PACKAGE_CBB		4		/* 515-pin 0.40 0.50 */
+#define OMAP_PACKAGE_CBC		3		/* 515-pin 0.50 0.65 */
+#define OMAP_PACKAGE_ZAC		2		/* 24xx 447-pin POP */
+#define OMAP_PACKAGE_ZAF		1		/* 2420 447-pin SIP */
 
 
 #define OMAP_MUX_NR_MODES	8			/* Available modes */

index 76b5bf7..197e295 100644
@@ -372,7 +372,7 @@ int __init omap2_mux_init(void)
 
 /*----------------------------------------------------------------------------*/
 
-#ifdef CONFIG_ARCH_OMAP3
+#ifdef CONFIG_ARCH_OMAP2PLUS
 static LIST_HEAD(muxmodes);
 static DEFINE_MUTEX(muxmode_mutex);
 

index 46315f2..937a8ca 100644
@@ -104,7 +104,7 @@ struct omap_board_mux {
 	u16	value;
 };
 
-#if defined(CONFIG_OMAP_MUX) && defined(CONFIG_ARCH_OMAP3)
+#if defined(CONFIG_OMAP_MUX)
 
 /**
  * omap_mux_init_gpio - initialize a signal based on the GPIO number

index 2ff4dce..f64d7ee 100644
@@ -2032,19 +2032,19 @@ int __init omap3_mux_init(struct omap_board_mux *board_subset, int flags)
 	struct omap_ball *package_balls;
 
 	switch (flags & OMAP_PACKAGE_MASK) {
-	case (OMAP_PACKAGE_CBC):
+	case OMAP_PACKAGE_CBC:
 		package_subset = omap3_cbc_subset;
 		package_balls = omap3_cbc_ball;
 		break;
-	case (OMAP_PACKAGE_CBB):
+	case OMAP_PACKAGE_CBB:
 		package_subset = omap3_cbb_subset;
 		package_balls = omap3_cbb_ball;
 		break;
-	case (OMAP_PACKAGE_CUS):
+	case OMAP_PACKAGE_CUS:
 		package_subset = omap3_cus_subset;
 		package_balls = omap3_cus_ball;
 		break;
-	case (OMAP_PACKAGE_CBP):
+	case OMAP_PACKAGE_CBP:
 		package_subset = omap36xx_cbp_subset;
 		package_balls = omap36xx_cbp_ball;
 		break;

index 937a8ca..e14cd4d 100644
@@ -7,6 +7,7 @@
  * published by the Free Software Foundation.
  */
 
+#include "mux2420.h"
 #include "mux34xx.h"
 
 #define OMAP_MUX_TERMINATOR	0xffff

@@ -173,6 +174,13 @@ void omap_mux_write(u16 val, u16 mux_offset);
 void omap_mux_write_array(struct omap_board_mux *board_mux);
 
 /**
+ * omap2420_mux_init() - initialize mux system with board specific set
+ * @board_mux:		Board specific mux table
+ * @flags:		OMAP package type used for the board
+ */
+int omap2420_mux_init(struct omap_board_mux *board_mux, int flags);
+
+/**
  * omap3_mux_init() - initialize mux system with board specific set
  * @board_mux:		Board specific mux table
  * @flags:		OMAP package type used for the board

688 lines not on this page · raw message

282 lines not on this page · raw message

index e14cd4d..a8e040c 100644
@@ -8,6 +8,7 @@
  */
 
 #include "mux2420.h"
+#include "mux2430.h"
 #include "mux34xx.h"
 
 #define OMAP_MUX_TERMINATOR	0xffff

@@ -181,6 +182,13 @@ void omap_mux_write_array(struct omap_board_mux *board_mux);
 int omap2420_mux_init(struct omap_board_mux *board_mux, int flags);
 
 /**
+ * omap2430_mux_init() - initialize mux system with board specific set
+ * @board_mux:		Board specific mux table
+ * @flags:		OMAP package type used for the board
+ */
+int omap2430_mux_init(struct omap_board_mux *board_mux, int flags);
+
+/**
  * omap3_mux_init() - initialize mux system with board specific set
  * @board_mux:		Board specific mux table
  * @flags:		OMAP package type used for the board

791 lines not on this page · raw message

370 lines not on this page · raw message

index 54a231c..8c58f51 100644
@@ -42,6 +42,8 @@
 #include <plat/dma.h>
 #include <plat/gpmc.h>
 
+#include "mux.h"
+
 #define H4_FLASH_CS	0
 #define H4_SMC91X_CS	1
 

@@ -338,8 +340,18 @@ static struct i2c_board_info __initdata h4_i2c_board_info[] = {
 	},
 };
 
+#ifdef CONFIG_OMAP_MUX
+static struct omap_board_mux board_mux[] __initdata = {
+	{ .reg_offset = OMAP_MUX_TERMINATOR },
+};
+#else
+#define board_mux	NULL
+#endif
+
 static void __init omap_h4_init(void)
 {
+	omap2420_mux_init(board_mux, OMAP_PACKAGE_ZAF);
+
 	/*
 	 * Make sure the serial ports are muxed on at this point.
 	 * You have to mux them off in device drivers later on

index 987b24d..b86a879 100644
@@ -42,6 +42,8 @@
 #include <plat/gpmc.h>
 #include <plat/control.h>
 
+#include "mux.h"
+
 /* LED & Switch macros */
 #define LED0_GPIO13		13
 #define LED1_GPIO14		14

@@ -309,10 +311,20 @@ static void __init apollon_usb_init(void)
 	omap2_usbfs_init(&apollon_usb_config);
 }
 
+#ifdef CONFIG_OMAP_MUX
+static struct omap_board_mux board_mux[] __initdata = {
+	{ .reg_offset = OMAP_MUX_TERMINATOR },
+};
+#else
+#define board_mux	NULL
+#endif
+
 static void __init omap_apollon_init(void)
 {
 	u32 v;
 
+	omap2420_mux_init(board_mux, OMAP_PACKAGE_ZAC);
+
 	apollon_led_init();
 	apollon_flash_init();
 	apollon_usb_init();

index 3ccc34e..5b9bbdc 100644
@@ -33,6 +33,8 @@
 #include <plat/mmc.h>
 #include <plat/serial.h>
 
+#include "mux.h"
+
 static int slot1_cover_open;
 static int slot2_cover_open;
 static struct device *mmc_device;

@@ -649,8 +651,17 @@ static void __init n8x0_init_irq(void)
 	omap_gpio_init();
 }
 
+#ifdef CONFIG_OMAP_MUX
+static struct omap_board_mux board_mux[] __initdata = {
+	{ .reg_offset = OMAP_MUX_TERMINATOR },
+};
+#else
+#define board_mux	NULL
+#endif
+
 static void __init n8x0_init_machine(void)
 {
+	omap2420_mux_init(board_mux, OMAP_PACKAGE_ZAC);
 	/* FIXME: add n810 spi devices */
 	spi_register_board_info(n800_spi_board_info,
 				ARRAY_SIZE(n800_spi_board_info));

index ec920c9..281aa13 100644
@@ -38,6 +38,7 @@
 #include <plat/usb.h>
 #include <plat/gpmc-smc91x.h>
 
+#include "mux.h"
 #include "hsmmc.h"
 
 #define SDP2430_CS0_BASE	0x04000000

@@ -217,10 +218,20 @@ static struct omap_usb_config sdp2430_usb_config __initdata = {
 	.pins[0]	= 3,
 };
 
+#ifdef CONFIG_OMAP_MUX
+static struct omap_board_mux board_mux[] __initdata = {
+	{ .reg_offset = OMAP_MUX_TERMINATOR },
+};
+#else
+#define board_mux	NULL
+#endif
+
 static void __init omap_2430sdp_init(void)
 {
 	int ret;
 
+	omap2430_mux_init(board_mux, OMAP_PACKAGE_ZAC);
+
 	omap2430_i2c_init();
 
 	platform_add_devices(sdp2430_devices, ARRAY_SIZE(sdp2430_devices));

index a445519..a216d88 100644
@@ -30,7 +30,6 @@
 #include <asm/irq.h>
 
 #include <plat/control.h>
-#include <plat/mux.h>
 #include <plat/usb.h>
 #include <plat/board.h>
 

@@ -40,6 +39,8 @@
 #define INT_USB_IRQ_HGEN	INT_24XX_USB_IRQ_HGEN
 #define INT_USB_IRQ_OTG		INT_24XX_USB_IRQ_OTG
 
+#include "mux.h"
+
 #if defined(CONFIG_ARCH_OMAP2)
 
 #ifdef	CONFIG_USB_GADGET_OMAP

@@ -209,13 +210,13 @@ static u32 __init omap2_usb0_init(unsigned nwires, unsigned is_device)
 		return 0;
 
 	if (is_device)
-		omap_cfg_reg(J20_24XX_USB0_PUEN);
+		omap_mux_init_signal("usb0_puen", 0);
 
-	omap_cfg_reg(K18_24XX_USB0_DAT);
-	omap_cfg_reg(K19_24XX_USB0_TXEN);
-	omap_cfg_reg(J14_24XX_USB0_SE0);
+	omap_mux_init_signal("usb0_dat", 0);
+	omap_mux_init_signal("usb0_txen", 0);
+	omap_mux_init_signal("usb0_se0", 0);
 	if (nwires != 3)
-		omap_cfg_reg(J18_24XX_USB0_RCV);
+		omap_mux_init_signal("usb0_rcv", 0);
 
 	switch (nwires) {
 	case 3:

@@ -228,8 +229,8 @@ static u32 __init omap2_usb0_init(unsigned nwires, unsigned is_device)
 		break;
 	case 6:
 		syscon1 = 3;
-		omap_cfg_reg(J19_24XX_USB0_VP);
-		omap_cfg_reg(K20_24XX_USB0_VM);
+		omap_mux_init_signal("usb0_vp", 0);
+		omap_mux_init_signal("usb0_vm", 0);
 		omap2_usb_devconf_set(0, USB_UNIDIR);
 		break;
 	default:

@@ -289,12 +290,12 @@ static u32 __init omap2_usb2_init(unsigned nwires, unsigned alt_pingroup)
 	if (alt_pingroup || nwires == 0)
 		return 0;
 
-	omap_cfg_reg(Y11_24XX_USB2_DAT);
-	omap_cfg_reg(AA10_24XX_USB2_SE0);
+	omap_mux_init_signal("usb2_dat", 0);
+	omap_mux_init_signal("usb2_se0", 0);
 	if (nwires > 2)
-		omap_cfg_reg(AA12_24XX_USB2_TXEN);
+		omap_mux_init_signal("usb2_txen", 0);
 	if (nwires > 3)
-		omap_cfg_reg(AA6_24XX_USB2_RCV);
+		omap_mux_init_signal("usb2_rcv", 0);
 
 	switch (nwires) {
 	case 2:

@@ -313,11 +314,13 @@ static u32 __init omap2_usb2_init(unsigned nwires, unsigned alt_pingroup)
 		omap2_usb_devconf_set(2, USB_BIDIR);
 		break;
 	case 5:
-		omap_cfg_reg(AA4_24XX_USB2_TLLSE0);
-		/* NOTE: board-specific code must override this setting if
-		 * this TLL link is not using DP/DM.  Something must also
+		/* NOTE: board-specific code must mux this setting depending
+		 * on TLL link using DP/DM.  Something must also
 		 * set up OTG_SYSCON2.HMC_TLL{ATTACH,SPEED}
+		 * 2420: hdq_sio.usb2_tllse0 or vlynq_rx0.usb2_tllse0
+		 * 2430: hdq_sio.usb2_tllse0 or sdmmc2_dat0.usb2_tllse0
 		 */
+
 		syscon1 = 3;
 		omap2_usb2_enable_5pinunitll();
 		break;

index 096f2ed..405ff7a 100644
@@ -292,6 +292,18 @@ static void __init omap_fsample_init(void)
 	omap_cfg_reg(L3_1610_FLASH_CS2B_OE);
 	omap_cfg_reg(M8_1610_FLASH_CS2B_WE);
 
+	/* Mux pins for keypad */
+	omap_cfg_reg(E2_7XX_KBR0);
+	omap_cfg_reg(J7_7XX_KBR1);
+	omap_cfg_reg(E1_7XX_KBR2);
+	omap_cfg_reg(F3_7XX_KBR3);
+	omap_cfg_reg(D2_7XX_KBR4);
+	omap_cfg_reg(C2_7XX_KBC0);
+	omap_cfg_reg(D3_7XX_KBC1);
+	omap_cfg_reg(E4_7XX_KBC2);
+	omap_cfg_reg(F4_7XX_KBC3);
+	omap_cfg_reg(E3_7XX_KBC4);
+
 	platform_add_devices(devices, ARRAY_SIZE(devices));
 
 	omap_board_config = fsample_config;

index 5f30188..ee46974 100644
@@ -437,6 +437,19 @@ static void __init h2_init(void)
 	/* omap_cfg_reg(U19_ARMIO1); */		/* CD */
 	omap_cfg_reg(BALLOUT_V8_ARMIO3);	/* WP */
 
+	/* Mux pins for keypad */
+	omap_cfg_reg(F18_1610_KBC0);
+	omap_cfg_reg(D20_1610_KBC1);
+	omap_cfg_reg(D19_1610_KBC2);
+	omap_cfg_reg(E18_1610_KBC3);
+	omap_cfg_reg(C21_1610_KBC4);
+	omap_cfg_reg(G18_1610_KBR0);
+	omap_cfg_reg(F19_1610_KBR1);
+	omap_cfg_reg(H14_1610_KBR2);
+	omap_cfg_reg(E20_1610_KBR3);
+	omap_cfg_reg(E19_1610_KBR4);
+	omap_cfg_reg(N19_1610_KBR5);
+
 	/* Irda */
 #if defined(CONFIG_OMAP_IR) || defined(CONFIG_OMAP_IR_MODULE)
 	omap_writel(omap_readl(FUNC_MUX_CTRL_A) | 7, FUNC_MUX_CTRL_A);

index 0be1d3b..a228e9d 100644
@@ -397,6 +397,19 @@ static void __init h3_init(void)
 	/* GPIO10 pullup/down register, Enable pullup on GPIO10 */
 	omap_cfg_reg(V2_1710_GPIO10);
 
+	/* Mux pins for keypad */
+	omap_cfg_reg(F18_1610_KBC0);
+	omap_cfg_reg(D20_1610_KBC1);
+	omap_cfg_reg(D19_1610_KBC2);
+	omap_cfg_reg(E18_1610_KBC3);
+	omap_cfg_reg(C21_1610_KBC4);
+	omap_cfg_reg(G18_1610_KBR0);
+	omap_cfg_reg(F19_1610_KBR1);
+	omap_cfg_reg(H14_1610_KBR2);
+	omap_cfg_reg(E20_1610_KBR3);
+	omap_cfg_reg(E19_1610_KBR4);
+	omap_cfg_reg(N19_1610_KBR5);
+
 	platform_add_devices(devices, ARRAY_SIZE(devices));
 	spi_register_board_info(h3_spi_board_info,
 				ARRAY_SIZE(h3_spi_board_info));

index e854d57..5069034 100644
@@ -260,6 +260,18 @@ static void __init omap_perseus2_init(void)
 	omap_cfg_reg(L3_1610_FLASH_CS2B_OE);
 	omap_cfg_reg(M8_1610_FLASH_CS2B_WE);
 
+	/* Mux pins for keypad */
+	omap_cfg_reg(E2_7XX_KBR0);
+	omap_cfg_reg(J7_7XX_KBR1);
+	omap_cfg_reg(E1_7XX_KBR2);
+	omap_cfg_reg(F3_7XX_KBR3);
+	omap_cfg_reg(D2_7XX_KBR4);
+	omap_cfg_reg(C2_7XX_KBC0);
+	omap_cfg_reg(D3_7XX_KBC1);
+	omap_cfg_reg(E4_7XX_KBC2);
+	omap_cfg_reg(F4_7XX_KBC3);
+	omap_cfg_reg(E3_7XX_KBC4);
+
 	platform_add_devices(devices, ARRAY_SIZE(devices));
 
 	omap_board_config = perseus2_config;

index 8c58f51..cdcd4fb 100644
@@ -363,11 +363,28 @@ static void __init omap_h4_init(void)
 #endif
 
 #if defined(CONFIG_KEYBOARD_OMAP) || defined(CONFIG_KEYBOARD_OMAP_MODULE)
+	omap_mux_init_gpio(88, OMAP_PULL_ENA | OMAP_PULL_UP);
+	omap_mux_init_gpio(89, OMAP_PULL_ENA | OMAP_PULL_UP);
+	omap_mux_init_gpio(124, OMAP_PULL_ENA | OMAP_PULL_UP);
+	omap_mux_init_signal("mcbsp2_dr.gpio_11", OMAP_PULL_ENA | OMAP_PULL_UP);
 	if (omap_has_menelaus()) {
+		omap_mux_init_signal("sdrc_a14.gpio0",
+			OMAP_PULL_ENA | OMAP_PULL_UP);
+		omap_mux_init_signal("vlynq_rx0.gpio_15", 0);
+		omap_mux_init_signal("gpio_98", 0);
 		row_gpios[5] = 0;
 		col_gpios[2] = 15;
 		col_gpios[6] = 18;
+	} else {
+		omap_mux_init_signal("gpio_96", OMAP_PULL_ENA | OMAP_PULL_UP);
+		omap_mux_init_signal("gpio_100", 0);
+		omap_mux_init_signal("gpio_98", 0);
 	}
+	omap_mux_init_signal("gpio_90", 0);
+	omap_mux_init_signal("gpio_91", 0);
+	omap_mux_init_signal("gpio_36", 0);
+	omap_mux_init_signal("mcbsp2_clkx.gpio_12", 0);
+	omap_mux_init_signal("gpio_97", 0);
 #endif
 
 	i2c_register_board_info(1, h4_i2c_board_info,

80 lines not on this page · raw message

index b86a879..bc67026 100644
@@ -332,6 +332,9 @@ static void __init omap_apollon_init(void)
 	/* REVISIT: where's the correct place */
 	omap_cfg_reg(W19_24XX_SYS_NIRQ);
 
+	/* LCD PWR_EN */
+	omap_mux_init_signal("mcbsp2_dr.gpio_11", OMAP_PULL_ENA | OMAP_PULL_UP);
+
 	/* Use Interal loop-back in MMC/SDIO Module Input Clock selection */
 	v = omap_ctrl_readl(OMAP2_CONTROL_DEVCONF0);
 	v |= (1 << 24);

index 2be94eb..10459d8 100644
@@ -25,7 +25,6 @@
 #include <linux/platform_device.h>
 
 #include <mach/gpio.h>
-#include <plat/mux.h>
 
 #include "omapfb.h"
 

@@ -34,8 +33,6 @@
 static int apollon_panel_init(struct lcd_panel *panel,
 				struct omapfb_device *fbdev)
 {
-	/* configure LCD PWR_EN */
-	omap_cfg_reg(M21_242X_GPIO11);
 	return 0;
 }
 

index 281aa13..71bf509 100644
@@ -31,7 +31,6 @@
 #include <asm/mach/map.h>
 
 #include <mach/gpio.h>
-#include <plat/mux.h>
 #include <plat/board.h>
 #include <plat/common.h>
 #include <plat/gpmc.h>

@@ -238,7 +237,10 @@ static void __init omap_2430sdp_init(void)
 	omap_serial_init();
 	omap2_hsmmc_init(mmc);
 	omap2_usbfs_init(&sdp2430_usb_config);
+
+	omap_mux_init_signal("usb0hs_stp", OMAP_PULL_ENA | OMAP_PULL_UP);
 	usb_musb_init(&musb_board_data);
+
 	board_smc91x_init();
 
 	/* Turn off secondary LCD backlight */

index e06d65e..5f04d3f 100644
@@ -194,10 +194,6 @@ int __init musb_platform_init(struct musb *musb, void *board_data)
 	u32 l;
 	struct omap_musb_board_data *data = board_data;
 
-#if defined(CONFIG_ARCH_OMAP2430)
-	omap_cfg_reg(AE5_2430_USB0HS_STP);
-#endif
-
 	/* We require some kind of external transceiver, hooked
 	 * up through ULPI.  TWL4030-family PMICs include one,
 	 * which needs a driver, drivers aren't always needed.

index 281aa13..71bf509 100644
@@ -31,7 +31,6 @@
 #include <asm/mach/map.h>
 
 #include <mach/gpio.h>
-#include <plat/mux.h>
 #include <plat/board.h>
 #include <plat/common.h>
 #include <plat/gpmc.h>

@@ -238,7 +237,10 @@ static void __init omap_2430sdp_init(void)
 	omap_serial_init();
 	omap2_hsmmc_init(mmc);
 	omap2_usbfs_init(&sdp2430_usb_config);
+
+	omap_mux_init_signal("usb0hs_stp", OMAP_PULL_ENA | OMAP_PULL_UP);
 	usb_musb_init(&musb_board_data);
+
 	board_smc91x_init();
 
 	/* Turn off secondary LCD backlight */

index bc67026..8cea623 100644
@@ -35,7 +35,6 @@
 
 #include <mach/gpio.h>
 #include <plat/led.h>
-#include <plat/mux.h>
 #include <plat/usb.h>
 #include <plat/board.h>
 #include <plat/common.h>

@@ -246,7 +245,7 @@ static inline void __init apollon_init_smc91x(void)
 	apollon_smc91x_resources[0].end   = base + 0x30f;
 	udelay(100);
 
-	omap_cfg_reg(W4__24XX_GPIO74);
+	omap_mux_init_gpio(74, 0);
 	if (gpio_request(APOLLON_ETHR_GPIO_IRQ, "SMC91x irq") < 0) {
 		printk(KERN_ERR "Failed to request GPIO%d for smc91x IRQ\n",
 			APOLLON_ETHR_GPIO_IRQ);

@@ -288,15 +287,15 @@ static void __init omap_apollon_init_irq(void)
 static void __init apollon_led_init(void)
 {
 	/* LED0 - AA10 */
-	omap_cfg_reg(AA10_242X_GPIO13);
+	omap_mux_init_signal("vlynq_clk.gpio_13", 0);
 	gpio_request(LED0_GPIO13, "LED0");
 	gpio_direction_output(LED0_GPIO13, 0);
 	/* LED1  - AA6 */
-	omap_cfg_reg(AA6_242X_GPIO14);
+	omap_mux_init_signal("vlynq_rx1.gpio_14", 0);
 	gpio_request(LED1_GPIO14, "LED1");
 	gpio_direction_output(LED1_GPIO14, 0);
 	/* LED2  - AA4 */
-	omap_cfg_reg(AA4_242X_GPIO15);
+	omap_mux_init_signal("vlynq_rx0.gpio_15", 0);
 	gpio_request(LED2_GPIO15, "LED2");
 	gpio_direction_output(LED2_GPIO15, 0);
 }

@@ -305,7 +304,7 @@ static void __init apollon_usb_init(void)
 {
 	/* USB device */
 	/* DEVICE_SUSPEND */
-	omap_cfg_reg(P21_242X_GPIO12);
+	omap_mux_init_signal("mcbsp2_clkx.gpio_12", 0);
 	gpio_request(12, "USB suspend");
 	gpio_direction_output(12, 0);
 	omap2_usbfs_init(&apollon_usb_config);

@@ -330,7 +329,7 @@ static void __init omap_apollon_init(void)
 	apollon_usb_init();
 
 	/* REVISIT: where's the correct place */
-	omap_cfg_reg(W19_24XX_SYS_NIRQ);
+	omap_mux_init_signal("sys_nirq", OMAP_PULL_ENA | OMAP_PULL_UP);
 
 	/* LCD PWR_EN */
 	omap_mux_init_signal("mcbsp2_dr.gpio_11", OMAP_PULL_ENA | OMAP_PULL_UP);

index cdcd4fb..2d9ff0f 100644
@@ -33,7 +33,6 @@
 
 #include <plat/control.h>
 #include <mach/gpio.h>
-#include <plat/mux.h>
 #include <plat/usb.h>
 #include <plat/board.h>
 #include <plat/common.h>

@@ -248,7 +247,7 @@ static inline void __init h4_init_debug(void)
 
 	udelay(100);
 
-	omap_cfg_reg(M15_24XX_GPIO92);
+	omap_mux_init_gpio(92, 0);
 	if (debug_card_init(cs_mem_base, H4_ETHR_GPIO_IRQ) < 0)
 		gpmc_cs_free(eth_cs);
 

@@ -358,8 +357,8 @@ static void __init omap_h4_init(void)
 	 * if not needed.
 	 */
 #if defined(CONFIG_OMAP_IR) || defined(CONFIG_OMAP_IR_MODULE)
-	omap_cfg_reg(K15_24XX_UART3_TX);
-	omap_cfg_reg(K14_24XX_UART3_RX);
+	omap_mux_init_signal("uart3_tx_irtx.uart3_tx_irtx", 0);
+	omap_mux_init_signal("uart3_rx_irrx.uart3_rx_irrx", 0);
 #endif
 
 #if defined(CONFIG_KEYBOARD_OMAP) || defined(CONFIG_KEYBOARD_OMAP_MODULE)

index 03e6c9e..3ae9d0a 100644
@@ -25,7 +25,6 @@
 #include <plat/control.h>
 #include <plat/tc.h>
 #include <plat/board.h>
-#include <plat/mux.h>
 #include <mach/gpio.h>
 #include <plat/mmc.h>
 #include <plat/dma.h>

@@ -672,19 +671,19 @@ static inline void omap2_mmc_mux(struct omap_mmc_platform_data *mmc_controller,
 					OMAP_PIN_INPUT_PULLUP);
 
 	if (cpu_is_omap2420() && controller_nr == 0) {
-		omap_cfg_reg(H18_24XX_MMC_CMD);
-		omap_cfg_reg(H15_24XX_MMC_CLKI);
-		omap_cfg_reg(G19_24XX_MMC_CLKO);
-		omap_cfg_reg(F20_24XX_MMC_DAT0);
-		omap_cfg_reg(F19_24XX_MMC_DAT_DIR0);
-		omap_cfg_reg(G18_24XX_MMC_CMD_DIR);
+		omap_mux_init_signal("sdmmc_cmd", 0);
+		omap_mux_init_signal("sdmmc_clki", 0);
+		omap_mux_init_signal("sdmmc_clko", 0);
+		omap_mux_init_signal("sdmmc_dat0", 0);
+		omap_mux_init_signal("sdmmc_dat_dir0", 0);
+		omap_mux_init_signal("sdmmc_cmd_dir", 0);
 		if (mmc_controller->slots[0].wires == 4) {
-			omap_cfg_reg(H14_24XX_MMC_DAT1);
-			omap_cfg_reg(E19_24XX_MMC_DAT2);
-			omap_cfg_reg(D19_24XX_MMC_DAT3);
-			omap_cfg_reg(E20_24XX_MMC_DAT_DIR1);
-			omap_cfg_reg(F18_24XX_MMC_DAT_DIR2);
-			omap_cfg_reg(E18_24XX_MMC_DAT_DIR3);
+			omap_mux_init_signal("sdmmc_dat1", 0);
+			omap_mux_init_signal("sdmmc_dat2", 0);
+			omap_mux_init_signal("sdmmc_dat3", 0);
+			omap_mux_init_signal("sdmmc_dat_dir1", 0);
+			omap_mux_init_signal("sdmmc_dat_dir2", 0);
+			omap_mux_init_signal("sdmmc_dat_dir3", 0);
 		}
 
 		/*

index 7951ae1..79c478c 100644
@@ -21,32 +21,19 @@
 
 #include <plat/cpu.h>
 #include <plat/i2c.h>
-#include <plat/mux.h>
 
 #include "mux.h"
 
 void __init omap2_i2c_mux_pins(int bus_id)
 {
-	if (cpu_is_omap24xx()) {
-		const int omap24xx_pins[][2] = {
-			{ M19_24XX_I2C1_SCL, L15_24XX_I2C1_SDA },
-			{ J15_24XX_I2C2_SCL, H19_24XX_I2C2_SDA },
-		};
-		int scl, sda;
-
-		scl = omap24xx_pins[bus_id - 1][0];
-		sda = omap24xx_pins[bus_id - 1][1];
-		omap_cfg_reg(sda);
-		omap_cfg_reg(scl);
-	}
+	char mux_name[sizeof("i2c2_scl.i2c2_scl")];
 
 	/* First I2C bus is not muxable */
-	if (cpu_is_omap34xx() && bus_id > 1) {
-		char mux_name[sizeof("i2c2_scl.i2c2_scl")];
+	if (bus_id == 1)
+		return;
 
-		sprintf(mux_name, "i2c%i_scl.i2c%i_scl", bus_id, bus_id);
-		omap_mux_init_signal(mux_name, OMAP_PIN_INPUT);
-		sprintf(mux_name, "i2c%i_sda.i2c%i_sda", bus_id, bus_id);
-		omap_mux_init_signal(mux_name, OMAP_PIN_INPUT);
-	}
+	sprintf(mux_name, "i2c%i_scl.i2c%i_scl", bus_id, bus_id);
+	omap_mux_init_signal(mux_name, OMAP_PIN_INPUT);
+	sprintf(mux_name, "i2c%i_sda.i2c%i_sda", bus_id, bus_id);
+	omap_mux_init_signal(mux_name, OMAP_PIN_INPUT);
 }

index c293370..87aa4c9 100644
@@ -20,17 +20,18 @@
 
 #include <mach/irqs.h>
 #include <plat/dma.h>
-#include <plat/mux.h>
 #include <plat/cpu.h>
 #include <plat/mcbsp.h>
 
+#include "mux.h"
+
 static void omap2_mcbsp2_mux_setup(void)
 {
-	omap_cfg_reg(Y15_24XX_MCBSP2_CLKX);
-	omap_cfg_reg(R14_24XX_MCBSP2_FSX);
-	omap_cfg_reg(W15_24XX_MCBSP2_DR);
-	omap_cfg_reg(V15_24XX_MCBSP2_DX);
-	omap_cfg_reg(V14_24XX_GPIO117);
+	omap_mux_init_signal("eac_ac_sclk.mcbsp2_clkx", OMAP_PULL_ENA);
+	omap_mux_init_signal("eac_ac_fs.mcbsp2_fsx", OMAP_PULL_ENA);
+	omap_mux_init_signal("eac_ac_din.mcbsp2_dr", OMAP_PULL_ENA);
+	omap_mux_init_signal("eac_ac_dout.mcbsp2_dx", OMAP_PULL_ENA);
+	omap_mux_init_gpio(117, OMAP_PULL_ENA);
 	/*
 	 * TODO: Need to add MUX settings for OMAP 2430 SDP
 	 */

index 10a2013..64a0112 100644
@@ -17,8 +17,8 @@
 #include <linux/usb/musb.h>
 
 #include <plat/gpmc.h>
-#include <plat/mux.h>
 
+#include "mux.h"
 
 static u8		async_cs, sync_cs;
 static unsigned		refclk_psec;

@@ -325,17 +325,17 @@ tusb6010_setup_interface(struct musb_hdrc_platform_data *data,
 	else {
 		/* assume OMAP 2420 ES2.0 and later */
 		if (dmachan & (1 << 0))
-			omap_cfg_reg(AA10_242X_DMAREQ0);
+			omap_mux_init_signal("sys_ndmareq0", 0);
 		if (dmachan & (1 << 1))
-			omap_cfg_reg(AA6_242X_DMAREQ1);
+			omap_mux_init_signal("sys_ndmareq1", 0);
 		if (dmachan & (1 << 2))
-			omap_cfg_reg(E4_242X_DMAREQ2);
+			omap_mux_init_signal("sys_ndmareq2", 0);
 		if (dmachan & (1 << 3))
-			omap_cfg_reg(G4_242X_DMAREQ3);
+			omap_mux_init_signal("sys_ndmareq3", 0);
 		if (dmachan & (1 << 4))
-			omap_cfg_reg(D3_242X_DMAREQ4);
+			omap_mux_init_signal("sys_ndmareq4", 0);
 		if (dmachan & (1 << 5))
-			omap_cfg_reg(E3_242X_DMAREQ5);
+			omap_mux_init_signal("sys_ndmareq5", 0);
 	}
 
 	/* so far so good ... register the device */

index 504d2bd..f267dc0 100644
@@ -18,7 +18,6 @@
 #include <plat/common.h>
 #include <plat/board.h>
 #include <plat/gpmc-smc91x.h>
-#include <plat/mux.h>
 #include <plat/usb.h>
 
 #include <mach/board-zoom.h>

index 16cc068..9a7f790 100644
@@ -26,7 +26,6 @@
 #include <asm/mach/map.h>
 
 #include <mach/gpio.h>
-#include <plat/mux.h>
 #include <plat/usb.h>
 #include <plat/board.h>
 #include <plat/common.h>

index abdf321..5ddf156 100644
@@ -25,7 +25,6 @@
 #include <linux/mmc/host.h>
 
 #include <plat/mcspi.h>
-#include <plat/mux.h>
 #include <plat/board.h>
 #include <plat/common.h>
 #include <plat/dma.h>

index b743a4f..5a1005b 100644
@@ -16,7 +16,6 @@
 #include <linux/mm.h>
 
 #include <asm/mach-types.h>
-#include <plat/mux.h>
 #include <plat/display.h>
 #include <plat/vram.h>
 #include <plat/mcspi.h>

index 3cfb425..b12d715 100644
@@ -28,7 +28,6 @@
 
 #include <asm/mach/map.h>
 
-#include <plat/mux.h>
 #include <plat/sram.h>
 #include <plat/sdrc.h>
 #include <plat/gpmc.h>

@@ -324,7 +323,6 @@ void __init omap2_init_common_hw(struct omap_sdrc_params *sdrc_cs0,
 		omap2430_hwmod_init();
 	else if (cpu_is_omap34xx())
 		omap3xxx_hwmod_init();
-	omap2_mux_init();
 	/* The OPP tables have to be registered before a clk init */
 	omap_pm_if_early_init(mpu_opps, dsp_opps, l3_opps);
 

313 lines not on this page · raw message

index e321281..6aeedea 100644
@@ -39,7 +39,6 @@
 #include <plat/clock.h>
 #include <plat/sram.h>
 #include <plat/control.h>
-#include <plat/mux.h>
 #include <plat/dma.h>
 #include <plat/board.h>
 

index d72d1ac..b11bf38 100644
@@ -23,7 +23,6 @@
 #include <linux/dma-mapping.h>
 
 #include <asm/io.h>
-#include <plat/mux.h>
 
 #include <mach/hardware.h>
 #include <mach/irqs.h>

index 96f6787..33a5cde 100644
@@ -28,7 +28,6 @@
 
 #include <mach/hardware.h>
 #include <mach/irqs.h>
-#include <plat/mux.h>
 #include <plat/usb.h>
 
 #ifdef CONFIG_USB_MUSB_SOC

243 lines not on this page · raw message

index 0670363..0d4aa0d 100644
@@ -54,7 +54,7 @@ int __init_or_module omap_cfg_reg(const unsigned long index)
 {
 	struct pin_config *reg;
 
-	if (cpu_is_omap34xx() || cpu_is_omap44xx()) {
+	if (!cpu_class_is_omap1()) {
 		printk(KERN_ERR "mux: Broken omap_cfg_reg(%lu) entry\n",
 				index);
 		WARN_ON(1);