ppc4xx: Enable booting with Option E on 460EX/EXr/GT

PATCH New Stefan Roese 1 participant 2 messages Jun 10, 2010 – Jul 1, 2010 PowerPC

Share & tools

Stefan Roese

author

2010-06-10 09:27 UTC #0 lore raw

PATCH 1/1 ppc4xx: Enable booting with Option E on 460EX/EXr/GT

This patch enables booting with option E on the PPC460EX/EXr/GT. When booting with Option E, the PLL is in bypass, CPR0_PLLC[ENG]=0. The Software Boot Configuration Procedure is needed to engage the PLL and perform a chip reset.

Signed-off-by Stefan Roese <[email protected]>

---
 arch/powerpc/cpu/ppc4xx/cpu_init.c |   49 ++++++++++++++++++++++++++++-------
 include/ppc440.h                   |    7 +++++
 2 files changed, 46 insertions(+), 10 deletions(-)

arch/powerpc/cpu/ppc4xx/cpu_init.c +39 ~~-10~~

index 8a6e545..c04eede 100644
@@ -36,6 +36,26 @@ DECLARE_GLOBAL_DATA_PTR;
 #define CONFIG_SYS_PLL_RECONFIG	0
 #endif
 
+#if defined(CONFIG_440EPX) || \
+    defined(CONFIG_460EX) || defined(CONFIG_460GT)
+static void reset_with_rli(void)
+{
+	u32 reg;
+
+	/*
+	 * Set reload inhibit so configuration will persist across
+	 * processor resets
+	 */
+	mfcpr(CPR0_ICFG, reg);
+	reg |= CPR0_ICFG_RLI_MASK;
+	mtcpr(CPR0_ICFG, reg);
+
+	/* Reset processor if configuration changed */
+	__asm__ __volatile__ ("sync; isync");
+	mtspr(SPRN_DBCR0, 0x20000000);
+}
+#endif
+
 void reconfigure_pll(u32 new_cpu_freq)
 {
 #if defined(CONFIG_440EPX)

@@ -166,19 +186,28 @@ void reconfigure_pll(u32 new_cpu_freq)
 		}
 	}
 
-	if (reset_needed) {
+	/* Now reset the CPU if needed */
+	if (reset_needed)
+		reset_with_rli();
+#endif
+
+#if defined(CONFIG_460EX) || defined(CONFIG_460GT)
+	u32 reg;
+
+	/*
+	 * See "9.2.1.1 Booting with Option E" in the 460EX/GT
+	 * users manual
+	 */
+	mfcpr(CPR0_PLLC, reg);
+	if ((reg & (CPR0_PLLC_RST | CPR0_PLLC_ENG)) == CPR0_PLLC_RST) {
 		/*
-		 * Set reload inhibit so configuration will persist across
-		 * processor resets
+		 * Set engage bit
 		 */
-		mfcpr(CPR0_ICFG, reg);
-		reg &= ~CPR0_ICFG_RLI_MASK;
-		reg |= 1 << 31;
-		mtcpr(CPR0_ICFG, reg);
+		reg = (reg & ~CPR0_PLLC_RST) | CPR0_PLLC_ENG;
+		mtcpr(CPR0_PLLC, reg);
 
-		/* Reset processor if configuration changed */
-		__asm__ __volatile__ ("sync; isync");
-		mtspr(SPRN_DBCR0, 0x20000000);
+		/* Now reset the CPU */
+		reset_with_rli();
 	}
 #endif
 }

include/ppc440.h +7 -0

index 5f87d2c..c807dda 100644
@@ -1719,6 +1719,13 @@
 #define CPR0_PERD_PERDV0_MASK	0x07000000
 #endif
 
+#if defined(CONFIG_460EX) || defined(CONFIG_460GT)
+#define CPR0_ICFG_RLI_MASK	0x80000000
+
+#define CPR0_PLLC_RST		0x80000000
+#define CPR0_PLLC_ENG		0x40000000
+#endif
+
 /*-----------------------------------------------------------------------------
 | PCI Internal Registers et. al. (accessed via plb)
 +----------------------------------------------------------------------------*/

Signature · 1 line

1.7.1

Stefan Roese

author

2010-07-01 08:28 UTC #1 lore raw

PATCH 1/1 ppc4xx: Enable booting with Option E on 460EX/EXr/GT

Quoted 4 lines · On Thursday 10 June 2010 11:27:23 Stefan Roese wrote:

This patch enables booting with option E on the PPC460EX/EXr/GT. When booting with Option E, the PLL is in bypass, CPR0_PLLC[ENG]=0. The Software Boot Configuration Procedure is needed to engage the PLL and perform a chip reset.

Applied to u-boot-ppc4xx/master. Thanks.

Cheers,
Stefan

--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-0 Fax: (+49)-8142-66989-80 Email: office at denx.de