Skip to contentSkip to conversation

x86: xsaveopt kernel enabling patches - v2

PATCH In review Suresh Siddha 1 participant 12 messages Jul 19, 2010 – Jul 20, 2010 x86

lore
Share & tools
lore
#0 lore raw

cover x86: xsaveopt kernel enabling patches - v2

AVX Programming Reference (June, 2010 version) located at
http://software.intel.com/en-us/avx/ refers to the optimized extended state save instruction "xsaveopt".

xsaveopt is similar to xsave and incorporates optimizations specifically targeted for speeding up context switch save, like:
a. if a state is in an INIT state, the instruction may clear the corresponding
bit in the xheader.bv with out writing the actual state in to the memory.
b. if the state hasn't been modified since the last xrstor, the instruction
may not write out the state to the save area.

Following patches enable the use of xsaveopt for context switch save/restore of the extended state.

changes in v2:
Split the cpu feature detection bits in to multiple patches along with the misc changes in the init_scattered_cpuid_features() -- Requested by hpa.

#1 lore raw

PATCH 1/5 x86: track the offset, size of features state in the xsave layout

Subleaves of the cpuid vector 0xd provides the offset and size of different feature state that are managed by the xsave/xrstor. Track this for the upcoming usage during signal handling.

---
 arch/x86/kernel/xsave.c |   29 +++++++++++++++++++++++++++++
 1 file changed, 29 insertions(+)
arch/x86/kernel/xsave.c +29 -0
Index: tip-linux-2.6/arch/x86/kernel/xsave.c
===================================================================
@@ -21,6 +21,8 @@ struct _fpx_sw_bytes fx_sw_reserved;
 struct _fpx_sw_bytes fx_sw_reserved_ia32;
 #endif
 
+static unsigned int *xstate_offsets, *xstate_sizes, xstate_features;
+
 /*
  * Check for the presence of extended state information in the
  * user fpstate pointer in the sigcontext.
@@ -294,12 +296,39 @@ void __cpuinit xsave_init(void)
 }
 
 /*
+ * Record the offsets and sizes of different state managed by the xsave
+ * memory layout.
+ */
+static void setup_xstate_features(void)
+{
+	int eax, ebx, ecx, edx, leaf = 0x2;
+
+	xstate_features = fls64(pcntxt_mask);
+	xstate_offsets = alloc_bootmem(xstate_features * sizeof(int));
+	xstate_sizes = alloc_bootmem(xstate_features * sizeof(int));
+
+	do {
+		cpuid_count(0xd, leaf, &eax, &ebx, &ecx, &edx);
+
+		if (eax == 0)
+			break;
+
+		xstate_offsets[leaf] = ebx;
+		xstate_sizes[leaf] = eax;
+
+		leaf++;
+	} while (1);
+}
+
+/*
  * setup the xstate image representing the init state
  */
 static void __init setup_xstate_init(void)
 {
 	init_xstate_buf = alloc_bootmem(xstate_size);
 	init_xstate_buf->i387.mxcsr = MXCSR_DEFAULT;
+
+	setup_xstate_features();
 }
 
 /*
#2 lore raw

[tip:x86/xsave] x86, xsave: Track the offset, size of state in the xsave layout

Commit-ID:  a1488f8bf4d72ad724700f6e982469a1240e4264
Gitweb:     http://git.kernel.org/tip/a1488f8bf4d72ad724700f6e982469a1240e4264
Author:     Suresh Siddha <[email protected]>
AuthorDate: Mon, 19 Jul 2010 16:05:48 -0700
Committer:  H. Peter Anvin <[email protected]>
CommitDate: Mon, 19 Jul 2010 17:51:17 -0700

x86, xsave: Track the offset, size of state in the xsave layout

Subleaves of the cpuid vector 0xd provides the offset and size of different feature state that are managed by the xsave/xrstor. Track this for the upcoming usage during signal handling.

LKML-Reference: <[email protected]>

---
 arch/x86/kernel/xsave.c |   29 +++++++++++++++++++++++++++++
 1 files changed, 29 insertions(+), 0 deletions(-)
arch/x86/kernel/xsave.c +29 -0
index 9801498..4993caa 100644
@@ -21,6 +21,8 @@ struct _fpx_sw_bytes fx_sw_reserved;
 struct _fpx_sw_bytes fx_sw_reserved_ia32;
 #endif
 
+static unsigned int *xstate_offsets, *xstate_sizes, xstate_features;
+
 /*
  * Check for the presence of extended state information in the
  * user fpstate pointer in the sigcontext.
@@ -302,12 +304,39 @@ void __cpuinit xsave_init(void)
 }
 
 /*
+ * Record the offsets and sizes of different state managed by the xsave
+ * memory layout.
+ */
+static void setup_xstate_features(void)
+{
+	int eax, ebx, ecx, edx, leaf = 0x2;
+
+	xstate_features = fls64(pcntxt_mask);
+	xstate_offsets = alloc_bootmem(xstate_features * sizeof(int));
+	xstate_sizes = alloc_bootmem(xstate_features * sizeof(int));
+
+	do {
+		cpuid_count(0xd, leaf, &eax, &ebx, &ecx, &edx);
+
+		if (eax == 0)
+			break;
+
+		xstate_offsets[leaf] = ebx;
+		xstate_sizes[leaf] = eax;
+
+		leaf++;
+	} while (1);
+}
+
+/*
  * setup the xstate image representing the init state
  */
 static void __init setup_xstate_init(void)
 {
 	init_xstate_buf = alloc_bootmem(xstate_size);
 	init_xstate_buf->i387.mxcsr = MXCSR_DEFAULT;
+
+	setup_xstate_features();
 }
 
 /*
#3 lore raw

PATCH 2/5 x86: sync xsave memory layout with its header for user handling

In reply to Suresh Siddha

With xsaveopt, if a processor implementation discern that a processor state component is in its initialized state it may modify the corresponding bit in the xsave_hdr.xstate_bv as '0', with out modifying the corresponding memory layout. Hence wHile presenting the xstate information to the user, we always ensure that the memory layout of a feature will be in the init state if the corresponding header bit is zero. This ensures the consistency and avoids the condition of the user seeing some some stale state in the memory layout during signal handling, debugging etc.

---
 arch/x86/include/asm/i387.h  |   14 ++++++
 arch/x86/include/asm/xsave.h |   10 ++++
 arch/x86/kernel/i387.c       |   11 +++++
 arch/x86/kernel/xsave.c      |   89 ++++++++++++++++++++++++++++++++++++++++++-
 4 files changed, 123 insertions(+), 1 deletion(-)
arch/x86/kernel/xsave.c +88 -1
Index: tip-linux-2.6/arch/x86/kernel/xsave.c
===================================================================
@@ -24,6 +24,76 @@ struct _fpx_sw_bytes fx_sw_reserved_ia32
 static unsigned int *xstate_offsets, *xstate_sizes, xstate_features;
 
 /*
+ * If a processor implementation discern that a processor state component is
+ * in its initialized state it may modify the corresponding bit in the
+ * xsave_hdr.xstate_bv as '0', with out modifying the corresponding memory
+ * layout in the case of xsaveopt. While presenting the xstate information to
+ * the user, we always ensure that the memory layout of a feature will be in
+ * the init state if the corresponding header bit is zero. This is to ensure
+ * that the user doesn't see some stale state in the memory layout during
+ * signal handling, debugging etc.
+ */
+void __sanitize_i387_state(struct task_struct *tsk)
+{
+	u64 xstate_bv;
+	int feature_bit = 0x2;
+	struct i387_fxsave_struct *fx = &tsk->thread.fpu.state->fxsave;
+
+	if (!fx)
+		return;
+
+	BUG_ON(task_thread_info(tsk)->status & TS_USEDFPU);
+
+	xstate_bv = tsk->thread.fpu.state->xsave.xsave_hdr.xstate_bv;
+
+	/*
+	 * None of the feature bits are in init state. So nothing else
+	 * to do for us, as the memory layout is upto date.
+	 */
+	if ((xstate_bv & pcntxt_mask) == pcntxt_mask)
+		return;
+
+	/*
+	 * FP is in init state
+	 */
+	if (!(xstate_bv & XSTATE_FP)) {
+		fx->cwd = 0x37f;
+		fx->swd = 0;
+		fx->twd = 0;
+		fx->fop = 0;
+		fx->rip = 0;
+		fx->rdp = 0;
+		memset(&fx->st_space[0], 0, 128);
+	}
+
+	/*
+	 * SSE is in init state
+	 */
+	if (!(xstate_bv & XSTATE_SSE))
+		memset(&fx->xmm_space[0], 0, 256);
+
+	xstate_bv = (pcntxt_mask & ~xstate_bv) >> 2;
+
+	/*
+	 * Update all the other memory layouts for which the corresponding
+	 * header bit is in the init state.
+	 */
+	while (xstate_bv) {
+		if (xstate_bv & 0x1) {
+			int offset = xstate_offsets[feature_bit];
+			int size = xstate_sizes[feature_bit];
+
+			memcpy(((void *) fx) + offset,
+			       ((void *) init_xstate_buf) + offset,
+			       size);
+		}
+
+		xstate_bv >>= 1;
+		feature_bit++;
+	}
+}
+
+/*
  * Check for the presence of extended state information in the
  * user fpstate pointer in the sigcontext.
  */
@@ -104,6 +174,7 @@ int save_i387_xstate(void __user *buf)
 		task_thread_info(tsk)->status &= ~TS_USEDFPU;
 		stts();
 	} else {
+		sanitize_i387_state(tsk);
 		if (__copy_to_user(buf, &tsk->thread.fpu.state->fxsave,
 				   xstate_size))
 			return -1;
@@ -325,10 +396,26 @@ static void setup_xstate_features(void)
  */
 static void __init setup_xstate_init(void)
 {
+	setup_xstate_features();
+
+	/*
+	 * Setup init_xstate_buf to represent the init state of
+	 * all the features managed by the xsave
+	 */
 	init_xstate_buf = alloc_bootmem(xstate_size);
 	init_xstate_buf->i387.mxcsr = MXCSR_DEFAULT;
 
-	setup_xstate_features();
+	clts();
+	/*
+	 * Init all the features state with header_bv being 0x0
+	 */
+	xrstor_state(init_xstate_buf, -1);
+	/*
+	 * Dump the init state again. This is to identify the init state
+	 * of any feature which is not represented by all zero's.
+	 */
+	xsave_state(init_xstate_buf, -1);
+	stts();
 }
 
 /*
arch/x86/kernel/i387.c +11 -0
Index: tip-linux-2.6/arch/x86/kernel/i387.c
===================================================================
@@ -190,6 +190,8 @@ int xfpregs_get(struct task_struct *targ
 	if (ret)
 		return ret;
 
+	sanitize_i387_state(target);
+
 	return user_regset_copyout(&pos, &count, &kbuf, &ubuf,
 				   &target->thread.fpu.state->fxsave, 0, -1);
 }
@@ -207,6 +209,8 @@ int xfpregs_set(struct task_struct *targ
 	if (ret)
 		return ret;
 
+	sanitize_i387_state(target);
+
 	ret = user_regset_copyin(&pos, &count, &kbuf, &ubuf,
 				 &target->thread.fpu.state->fxsave, 0, -1);
 
@@ -446,6 +450,8 @@ int fpregs_get(struct task_struct *targe
 					   -1);
 	}
 
+	sanitize_i387_state(target);
+
 	if (kbuf && pos == 0 && count == sizeof(env)) {
 		convert_from_fxsr(kbuf, target);
 		return 0;
@@ -467,6 +473,8 @@ int fpregs_set(struct task_struct *targe
 	if (ret)
 		return ret;
 
+	sanitize_i387_state(target);
+
 	if (!HAVE_HWFP)
 		return fpregs_soft_set(target, regset, pos, count, kbuf, ubuf);
 
@@ -533,6 +541,9 @@ static int save_i387_xsave(void __user *
 	struct _fpstate_ia32 __user *fx = buf;
 	int err = 0;
 
+
+	sanitize_i387_state(tsk);
+
 	/*
 	 * For legacy compatible, we always set FP/SSE bits in the bit
 	 * vector while saving the state to the user context.
arch/x86/include/asm/i387.h +14 -0
Index: tip-linux-2.6/arch/x86/include/asm/i387.h
===================================================================
@@ -58,11 +58,25 @@ extern int restore_i387_xstate_ia32(void
 
 #define X87_FSW_ES (1 << 7)	/* Exception Summary */
 
+static __always_inline __pure bool use_xsaveopt(void)
+{
+	return 0;
+}
+
 static __always_inline __pure bool use_xsave(void)
 {
 	return static_cpu_has(X86_FEATURE_XSAVE);
 }
 
+extern void __sanitize_i387_state(struct task_struct *);
+
+static inline void sanitize_i387_state(struct task_struct *tsk)
+{
+	if (!use_xsaveopt())
+		return;
+	__sanitize_i387_state(tsk);
+}
+
 #ifdef CONFIG_X86_64
 
 /* Ignore delayed exceptions from user space */
arch/x86/include/asm/xsave.h +10 -0
Index: tip-linux-2.6/arch/x86/include/asm/xsave.h
===================================================================
@@ -121,6 +121,16 @@ static inline void xrstor_state(struct x
 		     :   "memory");
 }
 
+static inline void xsave_state(struct xsave_struct *fx, u64 mask)
+{
+	u32 lmask = mask;
+	u32 hmask = mask >> 32;
+
+	asm volatile(".byte " REX_PREFIX "0x0f,0xae,0x27\n\t"
+		     : : "D" (fx), "m" (*fx), "a" (lmask), "d" (hmask)
+		     :   "memory");
+}
+
 static inline void fpu_xsave(struct fpu *fpu)
 {
 	/* This, however, we can work around by forcing the compiler to select
#4 lore raw

[tip:x86/xsave] x86, xsave: Sync xsave memory layout with its header for user handling

Commit-ID:  29104e101d710dd152f807978884643a52eca8b7
Gitweb:     http://git.kernel.org/tip/29104e101d710dd152f807978884643a52eca8b7
Author:     Suresh Siddha <[email protected]>
AuthorDate: Mon, 19 Jul 2010 16:05:49 -0700
Committer:  H. Peter Anvin <[email protected]>
CommitDate: Mon, 19 Jul 2010 17:51:30 -0700

x86, xsave: Sync xsave memory layout with its header for user handling

With xsaveopt, if a processor implementation discern that a processor state component is in its initialized state it may modify the corresponding bit in the xsave_hdr.xstate_bv as '0', with out modifying the corresponding memory layout. Hence wHile presenting the xstate information to the user, we always ensure that the memory layout of a feature will be in the init state if the corresponding header bit is zero. This ensures the consistency and avoids the condition of the user seeing some some stale state in the memory layout during signal handling, debugging etc.

LKML-Reference: <[email protected]>

---
 arch/x86/include/asm/i387.h  |   14 +++++++
 arch/x86/include/asm/xsave.h |   10 +++++
 arch/x86/kernel/i387.c       |   11 +++++
 arch/x86/kernel/xsave.c      |   89 +++++++++++++++++++++++++++++++++++++++++-
 4 files changed, 123 insertions(+), 1 deletions(-)
arch/x86/include/asm/i387.h +14 -0
index c991b3a..bb370fd 100644
@@ -58,11 +58,25 @@ extern int restore_i387_xstate_ia32(void __user *buf);
 
 #define X87_FSW_ES (1 << 7)	/* Exception Summary */
 
+static __always_inline __pure bool use_xsaveopt(void)
+{
+	return 0;
+}
+
 static __always_inline __pure bool use_xsave(void)
 {
 	return static_cpu_has(X86_FEATURE_XSAVE);
 }
 
+extern void __sanitize_i387_state(struct task_struct *);
+
+static inline void sanitize_i387_state(struct task_struct *tsk)
+{
+	if (!use_xsaveopt())
+		return;
+	__sanitize_i387_state(tsk);
+}
+
 #ifdef CONFIG_X86_64
 
 /* Ignore delayed exceptions from user space */
arch/x86/include/asm/xsave.h +10 -0
index 2c4390c..0c72adc 100644
@@ -111,6 +111,16 @@ static inline void xrstor_state(struct xsave_struct *fx, u64 mask)
 		     :   "memory");
 }
 
+static inline void xsave_state(struct xsave_struct *fx, u64 mask)
+{
+	u32 lmask = mask;
+	u32 hmask = mask >> 32;
+
+	asm volatile(".byte " REX_PREFIX "0x0f,0xae,0x27\n\t"
+		     : : "D" (fx), "m" (*fx), "a" (lmask), "d" (hmask)
+		     :   "memory");
+}
+
 static inline void fpu_xsave(struct fpu *fpu)
 {
 	/* This, however, we can work around by forcing the compiler to select
arch/x86/kernel/i387.c +11 -0
index 86cef6b..6106af9 100644
@@ -190,6 +190,8 @@ int xfpregs_get(struct task_struct *target, const struct user_regset *regset,
 	if (ret)
 		return ret;
 
+	sanitize_i387_state(target);
+
 	return user_regset_copyout(&pos, &count, &kbuf, &ubuf,
 				   &target->thread.fpu.state->fxsave, 0, -1);
 }
@@ -207,6 +209,8 @@ int xfpregs_set(struct task_struct *target, const struct user_regset *regset,
 	if (ret)
 		return ret;
 
+	sanitize_i387_state(target);
+
 	ret = user_regset_copyin(&pos, &count, &kbuf, &ubuf,
 				 &target->thread.fpu.state->fxsave, 0, -1);
 
@@ -446,6 +450,8 @@ int fpregs_get(struct task_struct *target, const struct user_regset *regset,
 					   -1);
 	}
 
+	sanitize_i387_state(target);
+
 	if (kbuf && pos == 0 && count == sizeof(env)) {
 		convert_from_fxsr(kbuf, target);
 		return 0;
@@ -467,6 +473,8 @@ int fpregs_set(struct task_struct *target, const struct user_regset *regset,
 	if (ret)
 		return ret;
 
+	sanitize_i387_state(target);
+
 	if (!HAVE_HWFP)
 		return fpregs_soft_set(target, regset, pos, count, kbuf, ubuf);
 
@@ -533,6 +541,9 @@ static int save_i387_xsave(void __user *buf)
 	struct _fpstate_ia32 __user *fx = buf;
 	int err = 0;
 
+
+	sanitize_i387_state(tsk);
+
 	/*
 	 * For legacy compatible, we always set FP/SSE bits in the bit
 	 * vector while saving the state to the user context.
arch/x86/kernel/xsave.c +88 -1

110 lines not on this page · raw message

#5 lore raw

PATCH 3/5 x86: extend init_scattered_cpuid_features() to consider cpuid subleaves

In reply to Suresh Siddha

cpuid features (like xsaveopt) are enumerated using cpuid subleaves.

Extend init_scattered_cpuid_features() to take subleaf into account.

---
 arch/x86/kernel/cpu/addon_cpuid_features.c |   25 +++++++++++++------------
 1 file changed, 13 insertions(+), 12 deletions(-)
arch/x86/kernel/cpu/addon_cpuid_features.c +13 -12
Index: tip-linux-2.6/arch/x86/kernel/cpu/addon_cpuid_features.c
===================================================================
@@ -14,6 +14,7 @@ struct cpuid_bit {
 	u8 reg;
 	u8 bit;
 	u32 level;
+	u32 sub_leaf;
 };
 
 enum cpuid_regs {
@@ -30,16 +31,16 @@ void __cpuinit init_scattered_cpuid_feat
 	const struct cpuid_bit *cb;
 
 	static const struct cpuid_bit __cpuinitconst cpuid_bits[] = {
-		{ X86_FEATURE_IDA,   		CR_EAX, 1, 0x00000006 },
-		{ X86_FEATURE_ARAT,  		CR_EAX, 2, 0x00000006 },
-		{ X86_FEATURE_APERFMPERF,	CR_ECX, 0, 0x00000006 },
-		{ X86_FEATURE_EPB,		CR_ECX, 3, 0x00000006 },
-		{ X86_FEATURE_CPB,   		CR_EDX, 9, 0x80000007 },
-		{ X86_FEATURE_NPT,   		CR_EDX, 0, 0x8000000a },
-		{ X86_FEATURE_LBRV,  		CR_EDX, 1, 0x8000000a },
-		{ X86_FEATURE_SVML,  		CR_EDX, 2, 0x8000000a },
-		{ X86_FEATURE_NRIPS, 		CR_EDX, 3, 0x8000000a },
-		{ 0, 0, 0, 0 }
+		{ X86_FEATURE_IDA,		CR_EAX, 1, 0x00000006, 0 },
+		{ X86_FEATURE_ARAT,		CR_EAX, 2, 0x00000006, 0 },
+		{ X86_FEATURE_APERFMPERF,	CR_ECX, 0, 0x00000006, 0 },
+		{ X86_FEATURE_EPB,		CR_ECX, 3, 0x00000006, 0 },
+		{ X86_FEATURE_CPB,		CR_EDX, 9, 0x80000007, 0 },
+		{ X86_FEATURE_NPT,		CR_EDX, 0, 0x8000000a, 0 },
+		{ X86_FEATURE_LBRV,		CR_EDX, 1, 0x8000000a, 0 },
+		{ X86_FEATURE_SVML,		CR_EDX, 2, 0x8000000a, 0 },
+		{ X86_FEATURE_NRIPS,		CR_EDX, 3, 0x8000000a, 0 },
+		{ 0, 0, 0, 0, 0 }
 	};
 
 	for (cb = cpuid_bits; cb->feature; cb++) {
@@ -50,8 +51,8 @@ void __cpuinit init_scattered_cpuid_feat
 		    max_level > (cb->level | 0xffff))
 			continue;
 
-		cpuid(cb->level, &regs[CR_EAX], &regs[CR_EBX],
-			&regs[CR_ECX], &regs[CR_EDX]);
+		cpuid_count(cb->level, cb->sub_leaf, &regs[CR_EAX],
+			    &regs[CR_EBX], &regs[CR_ECX], &regs[CR_EDX]);
 
 		if (regs[cb->reg] & (1 << cb->bit))
 			set_cpu_cap(c, cb->feature);
#6 lore raw

[tip:x86/cpu] x86, cpu: Make init_scattered_cpuid_features() consider cpuid subleaves

Commit-ID:  edb18f8ab02843453306601c4aa697f9691129cd
Gitweb:     http://git.kernel.org/tip/edb18f8ab02843453306601c4aa697f9691129cd
Author:     Suresh Siddha <[email protected]>
AuthorDate: Mon, 19 Jul 2010 16:05:50 -0700
Committer:  H. Peter Anvin <[email protected]>
CommitDate: Mon, 19 Jul 2010 16:47:59 -0700

x86, cpu: Make init_scattered_cpuid_features() consider cpuid subleaves

Some cpuid features (like xsaveopt) are enumerated using cpuid subleaves.

Extend init_scattered_cpuid_features() to take subleaf into account.

LKML-Reference: <[email protected]>

---
 arch/x86/kernel/cpu/addon_cpuid_features.c |   25 +++++++++++++------------
 1 files changed, 13 insertions(+), 12 deletions(-)
arch/x86/kernel/cpu/addon_cpuid_features.c +13 -12
index 7369b4c..03cf24a 100644
@@ -14,6 +14,7 @@ struct cpuid_bit {
 	u8 reg;
 	u8 bit;
 	u32 level;
+	u32 sub_leaf;
 };
 
 enum cpuid_regs {
@@ -30,16 +31,16 @@ void __cpuinit init_scattered_cpuid_features(struct cpuinfo_x86 *c)
 	const struct cpuid_bit *cb;
 
 	static const struct cpuid_bit __cpuinitconst cpuid_bits[] = {
-		{ X86_FEATURE_IDA,   		CR_EAX, 1, 0x00000006 },
-		{ X86_FEATURE_ARAT,  		CR_EAX, 2, 0x00000006 },
-		{ X86_FEATURE_APERFMPERF,	CR_ECX, 0, 0x00000006 },
-		{ X86_FEATURE_EPB,		CR_ECX, 3, 0x00000006 },
-		{ X86_FEATURE_CPB,   		CR_EDX, 9, 0x80000007 },
-		{ X86_FEATURE_NPT,   		CR_EDX, 0, 0x8000000a },
-		{ X86_FEATURE_LBRV,  		CR_EDX, 1, 0x8000000a },
-		{ X86_FEATURE_SVML,  		CR_EDX, 2, 0x8000000a },
-		{ X86_FEATURE_NRIPS, 		CR_EDX, 3, 0x8000000a },
-		{ 0, 0, 0, 0 }
+		{ X86_FEATURE_IDA,		CR_EAX, 1, 0x00000006, 0 },
+		{ X86_FEATURE_ARAT,		CR_EAX, 2, 0x00000006, 0 },
+		{ X86_FEATURE_APERFMPERF,	CR_ECX, 0, 0x00000006, 0 },
+		{ X86_FEATURE_EPB,		CR_ECX, 3, 0x00000006, 0 },
+		{ X86_FEATURE_CPB,		CR_EDX, 9, 0x80000007, 0 },
+		{ X86_FEATURE_NPT,		CR_EDX, 0, 0x8000000a, 0 },
+		{ X86_FEATURE_LBRV,		CR_EDX, 1, 0x8000000a, 0 },
+		{ X86_FEATURE_SVML,		CR_EDX, 2, 0x8000000a, 0 },
+		{ X86_FEATURE_NRIPS,		CR_EDX, 3, 0x8000000a, 0 },
+		{ 0, 0, 0, 0, 0 }
 	};
 
 	for (cb = cpuid_bits; cb->feature; cb++) {
@@ -50,8 +51,8 @@ void __cpuinit init_scattered_cpuid_features(struct cpuinfo_x86 *c)
 		    max_level > (cb->level | 0xffff))
 			continue;
 
-		cpuid(cb->level, &regs[CR_EAX], &regs[CR_EBX],
-			&regs[CR_ECX], &regs[CR_EDX]);
+		cpuid_count(cb->level, cb->sub_leaf, &regs[CR_EAX],
+			    &regs[CR_EBX], &regs[CR_ECX], &regs[CR_EDX]);
 
 		if (regs[cb->reg] & (1 << cb->bit))
 			set_cpu_cap(c, cb->feature);
#7 lore raw

PATCH 4/5 x86: Add xsaveopt cpufeature

In reply to Suresh Siddha

Add cpu feature bit support for the XSAVEOPT instruction.

---
 arch/x86/include/asm/cpufeature.h |    1 +
 1 file changed, 1 insertion(+)
arch/x86/include/asm/cpufeature.h +1 -0
Index: tip-linux-2.6/arch/x86/include/asm/cpufeature.h
===================================================================
@@ -165,6 +165,7 @@
 #define X86_FEATURE_ARAT	(7*32+ 1) /* Always Running APIC Timer */
 #define X86_FEATURE_CPB		(7*32+ 2) /* AMD Core Performance Boost */
 #define X86_FEATURE_EPB		(7*32+ 3) /* IA32_ENERGY_PERF_BIAS support */
+#define X86_FEATURE_XSAVEOPT	(7*32+4) /* "xsaveopt" Optimized Xsave */
 
 /* Virtualization flags: Linux defined, word 8 */
 #define X86_FEATURE_TPR_SHADOW  (8*32+ 0) /* Intel TPR Shadow */
#8 lore raw

[tip:x86/cpu] x86, cpu: Add xsaveopt cpufeature

Commit-ID:  40e1d7a4ffee5cb17f5c36f4c3c4a011ab103ebe
Gitweb:     http://git.kernel.org/tip/40e1d7a4ffee5cb17f5c36f4c3c4a011ab103ebe
Author:     Suresh Siddha <[email protected]>
AuthorDate: Mon, 19 Jul 2010 16:05:51 -0700
Committer:  H. Peter Anvin <[email protected]>
CommitDate: Mon, 19 Jul 2010 16:48:06 -0700

x86, cpu: Add xsaveopt cpufeature

Add cpu feature bit support for the XSAVEOPT instruction.

LKML-Reference: <[email protected]>

---
 arch/x86/include/asm/cpufeature.h |    1 +
 1 files changed, 1 insertions(+), 0 deletions(-)
arch/x86/include/asm/cpufeature.h +1 -0
index 3ec9275..d5ea3e3 100644
@@ -165,6 +165,7 @@
 #define X86_FEATURE_ARAT	(7*32+ 1) /* Always Running APIC Timer */
 #define X86_FEATURE_CPB		(7*32+ 2) /* AMD Core Performance Boost */
 #define X86_FEATURE_EPB		(7*32+ 3) /* IA32_ENERGY_PERF_BIAS support */
+#define X86_FEATURE_XSAVEOPT	(7*32+4) /* "xsaveopt" Optimized Xsave */
 
 /* Virtualization flags: Linux defined, word 8 */
 #define X86_FEATURE_TPR_SHADOW  (8*32+ 0) /* Intel TPR Shadow */
#9 lore raw

PATCH 5/5 x86: use xsaveopt in context-switch path when supported

In reply to Suresh Siddha

xsaveopt is a more optimized form of xsave specifically designed for the context switch usage. xsaveopt doesn't save the state that's not modified from the prior xrstor. And if a specific feature state gets modified to the init state, then xsaveopt just updates the header bit in the xsave memory layout without updating the corresponding memory layout.

---
 arch/x86/include/asm/i387.h                |    2 +-
 arch/x86/include/asm/xsave.h               |    9 ++++++---
 arch/x86/kernel/cpu/addon_cpuid_features.c |    1 +
 arch/x86/kernel/cpu/common.c               |    8 ++++++++
 4 files changed, 16 insertions(+), 4 deletions(-)
arch/x86/include/asm/xsave.h +6 -3
Index: tip-linux-2.6/arch/x86/include/asm/xsave.h
===================================================================
@@ -135,8 +135,11 @@ static inline void fpu_xsave(struct fpu 
 {
 	/* This, however, we can work around by forcing the compiler to select
 	   an addressing mode that doesn't require extended registers. */
-	__asm__ __volatile__(".byte " REX_PREFIX "0x0f,0xae,0x27"
-			     : : "D" (&(fpu->state->xsave)),
-				 "a" (-1), "d"(-1) : "memory");
+	alternative_input(
+		".byte " REX_PREFIX "0x0f,0xae,0x27",
+		".byte " REX_PREFIX "0x0f,0xae,0x37",
+		X86_FEATURE_XSAVEOPT,
+		[fx] "D" (&fpu->state->xsave), "a" (-1), "d" (-1) :
+		"memory");
 }
 #endif
arch/x86/kernel/cpu/common.c +8 -0
Index: tip-linux-2.6/arch/x86/kernel/cpu/common.c
===================================================================
@@ -140,10 +140,18 @@ EXPORT_PER_CPU_SYMBOL_GPL(gdt_page);
 static int __init x86_xsave_setup(char *s)
 {
 	setup_clear_cpu_cap(X86_FEATURE_XSAVE);
+	setup_clear_cpu_cap(X86_FEATURE_XSAVEOPT);
 	return 1;
 }
 __setup("noxsave", x86_xsave_setup);
 
+static int __init x86_xsaveopt_setup(char *s)
+{
+	setup_clear_cpu_cap(X86_FEATURE_XSAVEOPT);
+	return 1;
+}
+__setup("noxsaveopt", x86_xsaveopt_setup);
+
 #ifdef CONFIG_X86_32
 static int cachesize_override __cpuinitdata = -1;
 static int disable_x86_serial_nr __cpuinitdata = 1;
arch/x86/include/asm/i387.h +1 -1
Index: tip-linux-2.6/arch/x86/include/asm/i387.h
===================================================================
@@ -60,7 +60,7 @@ extern int restore_i387_xstate_ia32(void
 
 static __always_inline __pure bool use_xsaveopt(void)
 {
-	return 0;
+	return static_cpu_has(X86_FEATURE_XSAVEOPT);
 }
 
 static __always_inline __pure bool use_xsave(void)
arch/x86/kernel/cpu/addon_cpuid_features.c +1 -0
Index: tip-linux-2.6/arch/x86/kernel/cpu/addon_cpuid_features.c
===================================================================
@@ -35,6 +35,7 @@ void __cpuinit init_scattered_cpuid_feat
 		{ X86_FEATURE_ARAT,		CR_EAX, 2, 0x00000006, 0 },
 		{ X86_FEATURE_APERFMPERF,	CR_ECX, 0, 0x00000006, 0 },
 		{ X86_FEATURE_EPB,		CR_ECX, 3, 0x00000006, 0 },
+		{ X86_FEATURE_XSAVEOPT,		CR_EAX,	0, 0x0000000d, 1 },
 		{ X86_FEATURE_CPB,		CR_EDX, 9, 0x80000007, 0 },
 		{ X86_FEATURE_NPT,		CR_EDX, 0, 0x8000000a, 0 },
 		{ X86_FEATURE_LBRV,		CR_EDX, 1, 0x8000000a, 0 },
#10 lore raw

[tip:x86/cpu] x86, cpu: Enumerate xsaveopt

Commit-ID:  5734f62b6601d88fd8ec720cb56b93fd3a030557
Gitweb:     http://git.kernel.org/tip/5734f62b6601d88fd8ec720cb56b93fd3a030557
Author:     Suresh Siddha <[email protected]>
AuthorDate: Mon, 19 Jul 2010 16:05:52 -0700
Committer:  H. Peter Anvin <[email protected]>
CommitDate: Mon, 19 Jul 2010 16:50:40 -0700

x86, cpu: Enumerate xsaveopt

Enumerate the xsaveopt feature.

LKML-Reference: <[email protected]>

---
 arch/x86/kernel/cpu/addon_cpuid_features.c |    1 +
 1 files changed, 1 insertions(+), 0 deletions(-)
arch/x86/kernel/cpu/addon_cpuid_features.c +1 -0
index 03cf24a..41eebcd 100644
@@ -35,6 +35,7 @@ void __cpuinit init_scattered_cpuid_features(struct cpuinfo_x86 *c)
 		{ X86_FEATURE_ARAT,		CR_EAX, 2, 0x00000006, 0 },
 		{ X86_FEATURE_APERFMPERF,	CR_ECX, 0, 0x00000006, 0 },
 		{ X86_FEATURE_EPB,		CR_ECX, 3, 0x00000006, 0 },
+		{ X86_FEATURE_XSAVEOPT,		CR_EAX,	0, 0x0000000d, 1 },
 		{ X86_FEATURE_CPB,		CR_EDX, 9, 0x80000007, 0 },
 		{ X86_FEATURE_NPT,		CR_EDX, 0, 0x8000000a, 0 },
 		{ X86_FEATURE_LBRV,		CR_EDX, 1, 0x8000000a, 0 },
#11 lore raw

[tip:x86/xsave] x86, xsave: Use xsaveopt in context-switch path when supported

In reply to Suresh Siddha
Commit-ID:  6bad06b768920e278c7cedfdda56a0b4c6a35ee9
Gitweb:     http://git.kernel.org/tip/6bad06b768920e278c7cedfdda56a0b4c6a35ee9
Author:     Suresh Siddha <[email protected]>
AuthorDate: Mon, 19 Jul 2010 16:05:52 -0700
Committer:  H. Peter Anvin <[email protected]>
CommitDate: Mon, 19 Jul 2010 17:52:24 -0700

x86, xsave: Use xsaveopt in context-switch path when supported

xsaveopt is a more optimized form of xsave specifically designed for the context switch usage. xsaveopt doesn't save the state that's not modified from the prior xrstor. And if a specific feature state gets modified to the init state, then xsaveopt just updates the header bit in the xsave memory layout without updating the corresponding memory layout.

LKML-Reference: <[email protected]>

---
 arch/x86/include/asm/i387.h  |    2 +-
 arch/x86/include/asm/xsave.h |    9 ++++++---
 arch/x86/kernel/cpu/common.c |    8 ++++++++
 3 files changed, 15 insertions(+), 4 deletions(-)
arch/x86/include/asm/i387.h +1 -1
index bb370fd..59bd93a 100644
@@ -60,7 +60,7 @@ extern int restore_i387_xstate_ia32(void __user *buf);
 
 static __always_inline __pure bool use_xsaveopt(void)
 {
-	return 0;
+	return static_cpu_has(X86_FEATURE_XSAVEOPT);
 }
 
 static __always_inline __pure bool use_xsave(void)
arch/x86/include/asm/xsave.h +6 -3
index 0c72adc..ec86c5f 100644
@@ -125,8 +125,11 @@ static inline void fpu_xsave(struct fpu *fpu)
 {
 	/* This, however, we can work around by forcing the compiler to select
 	   an addressing mode that doesn't require extended registers. */
-	__asm__ __volatile__(".byte " REX_PREFIX "0x0f,0xae,0x27"
-			     : : "D" (&(fpu->state->xsave)),
-				 "a" (-1), "d"(-1) : "memory");
+	alternative_input(
+		".byte " REX_PREFIX "0x0f,0xae,0x27",
+		".byte " REX_PREFIX "0x0f,0xae,0x37",
+		X86_FEATURE_XSAVEOPT,
+		[fx] "D" (&fpu->state->xsave), "a" (-1), "d" (-1) :
+		"memory");
 }
 #endif
arch/x86/kernel/cpu/common.c +8 -0
index c735830..3f715ef 100644
@@ -140,10 +140,18 @@ EXPORT_PER_CPU_SYMBOL_GPL(gdt_page);
 static int __init x86_xsave_setup(char *s)
 {
 	setup_clear_cpu_cap(X86_FEATURE_XSAVE);
+	setup_clear_cpu_cap(X86_FEATURE_XSAVEOPT);
 	return 1;
 }
 __setup("noxsave", x86_xsave_setup);
 
+static int __init x86_xsaveopt_setup(char *s)
+{
+	setup_clear_cpu_cap(X86_FEATURE_XSAVEOPT);
+	return 1;
+}
+__setup("noxsaveopt", x86_xsaveopt_setup);
+
 #ifdef CONFIG_X86_32
 static int cachesize_override __cpuinitdata = -1;
 static int disable_x86_serial_nr __cpuinitdata = 1;