Skip to contentSkip to conversation

PROBLEM: additional serial ports on MS9830 board do not work (IRQ problems)

DISCUSSION Jan Kandziora 2 participants 3 messages Sep 5, 2010 – Sep 6, 2010

lore
Share & tools
lore
#0 lore raw

Hello,

Summary:        additional serial ports on MS9830 board do not work
Keywords:       serial
Kernel version: 2.6.35.4

I have problems with the IRQs of a MS9830 Mini ITX board. The board has 1 serial port on a DB9 connector and 4 additional ones on internal connectors, which can also be powered. The computer has a touchscreen controller connected to one of those internal ports.

The internal ports seem to be special as they don't work correctly. Depending on BIOS settings, I either don't get any IRQs from them or I get IRQs but the serial driver doesn't claim them.

To make the bug hunt simpler, I disabled all ports but one of the internal ones, which I've set to 0x3F8/IRQ4. Then I open the port with "od /dev/ttyS0" and touch the screen. After some seconds I get

<3>irq 4: nobody cared (try booting with the "irqpoll" option) <4>Pid: 3923, comm: exe Not tainted 2.6.35.4 #1
<4>Call Trace:
<4> [<c103a950>] __report_bad_irq+0x2e/0x6f
<4> [<c103aa81>] note_interrupt+0xf0/0x147
<4> [<c103b042>] handle_level_irq+0x6d/0x99
<4> [<c1003b32>] handle_irq+0x1a/0x20
<4> [<c1003883>] do_IRQ+0x33/0x75
<4> [<c1002b69>] common_interrupt+0x29/0x30
<4> [<c101d8c8>] ? __do_softirq+0x34/0xca
<4> [<c101d983>] do_softirq+0x25/0x2a
<4> [<c101da43>] irq_exit+0x28/0x57
<4> [<c10038b0>] do_IRQ+0x60/0x75
<4> [<c1002b69>] common_interrupt+0x29/0x30
<4> [<c103007b>] ? timecompare_offset+0x9c/0x2c6
<4> [<c103a3ec>] ? __setup_irq+0x1d8/0x259
<4> [<c103a510>] request_threaded_irq+0xa3/0xd0
<4> [<c119f173>] ? serial8250_interrupt+0x0/0xb2
<4> [<c119ec07>] serial8250_startup+0x3f5/0x53d
<4> [<c119bfa9>] uart_startup+0x6e/0x101
<4> [<c119ca89>] uart_open+0xff/0x2ac
<4> [<c114fee7>] ? tty_init_dev+0xb7/0xf0
<4> [<c11501ab>] tty_open+0x28b/0x354
<4> [<c106336e>] chrdev_open+0xc0/0xd7
<4> [<c1060141>] __dentry_open+0xd1/0x1a7
<4> [<c10602ad>] nameidata_to_filp+0x29/0x3d
<4> [<c10632ae>] ? chrdev_open+0x0/0xd7
<4> [<c1068a92>] do_last+0x3d1/0x4d1
<4> [<c106a13f>] do_filp_open+0x17c/0x41e
<4> [<c10124c0>] ? do_page_fault+0x2a1/0x2cf
<4> [<c105ff43>] do_sys_open+0x48/0x116
<4> [<c1060053>] sys_open+0x1e/0x26
<4> [<c1002650>] sysenter_do_call+0x12/0x26 <3>handlers:
<3>[<c119f173>] (serial8250_interrupt+0x0/0xb2) <0>Disabling IRQ #4
<4>ttyS0: 1 input overrun(s)
<6>usb 4-1: new full speed USB device using uhci_hcd and address 2 <4>ttyS0: 10 input overrun(s)

in dmesg and some data from the touch controller. But it's very jumpy without interrupts, hardly useable.

I tried the suggested option "irqpoll", but then the computer just freezes when I do "od /dev/ttyS0" and touch the screen. No kernel panic, just a hard freeze. I tried "acpi=noirq", "acpi=off" and disabling the APIC in the BIOS setup, too. None of these made the serial irq work.

Can you give me any useful pointers what to try next? Kernel configuration is attached.

Kind regards

Jan

#1 lore raw
Quoted 4 lines

I tried the suggested option "irqpoll", but then the computer just freezes when I do "od /dev/ttyS0" and touch the screen. No kernel panic, just a hard freeze. I tried "acpi=noirq", "acpi=off" and disabling the APIC in the BIOS setup, too. None of these made the serial irq work.

I suspect you need a BIOS which has correct tables for IRQ routing.

Quoted 2 lines

Can you give me any useful pointers what to try next? Kernel configuration is attached.

Vendor for BIOS update would be the obvious starting point.

#2 lore raw

Am Montag, 6. September 2010 schrieb Alan Cox:

Quoted 8 lines

I suspect you need a BIOS which has correct tables for IRQ routing.

Quoted 2 lines

Can you give me any useful pointers what to try next? Kernel configuration is attached.

Vendor for BIOS update would be the obvious starting point.

Ok, done. Now I have V3.2 instead of V3.0 and things have changed some way: if I enable only the first of the internal ports as 0x3f8/4, no tty shows up at all. If I enable the DB9 port as 0x2f8/3 and the first internal port as 0x3f8/4, only the DB9 port shows up as ttyS1. Other permutations bring other oddities with some enabled ttys showing up, some not. (And the BIOS update broke LVDS. Hardware vendors make me sick...)

Aside from that, I noticed no difference. I filed a bug report at the manufacturer of that POS PC the board is inside but I doubt there will be any reaction, at least not in time.

Is there some tweaking I can try from within Linux? Some things I tried are:
==================
If I enable the DB9-Port as 0x3f8/4 and the first of the internal ports as 0x3e8/11, I get the following:

<6>serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A <6>serial8250: ttyS2 at I/O 0x3e8 (irq = 4) is a 16550A <6>00:06: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A <6>00:08: ttyS2 at I/O 0x3e8 (irq = 11) is a 16550A

No other tty messages. I can receive is some data from ttyS2, but it is broken. At the same time ttyS0, the DB9 port, works without problems. That's the same as before the BIOS update.

==================
If I enable the DB9-Port as 0x3f8/4 and the first of the internal ports as 0x3e8/4, I get the following:

<6>serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A <6>serial8250: ttyS2 at I/O 0x3e8 (irq = 4) is a 16550A <6>00:06: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A <6>00:08: ttyS2 at I/O 0x3e8 (irq = 4) is a 16550A

and later, when /dev/ttyS2 is accessed, again:

<3>irq 4: nobody cared (try booting with the "irqpoll" option) <4>Pid: 3798, comm: X Not tainted 2.6.35.4 #1 <4>Call Trace:
<4> [<c103a950>] __report_bad_irq+0x2e/0x6f
<4> [<c103aa81>] note_interrupt+0xf0/0x147
<4> [<c103b042>] handle_level_irq+0x6d/0x99
<4> [<c1003b32>] handle_irq+0x1a/0x20
<4> [<c1003883>] do_IRQ+0x33/0x75
<4> [<c1002b69>] common_interrupt+0x29/0x30
<4> [<c101d8c8>] ? __do_softirq+0x34/0xca
<4> [<c101d983>] do_softirq+0x25/0x2a
<4> [<c101da43>] irq_exit+0x28/0x57
<4> [<c10038b0>] do_IRQ+0x60/0x75
<4> [<c1002b69>] common_interrupt+0x29/0x30
<4> [<c103007b>] ? timecompare_offset+0x9c/0x2c6
<4> [<c103a3ec>] ? __setup_irq+0x1d8/0x259
<4> [<c103a510>] request_threaded_irq+0xa3/0xd0
<4> [<c119f173>] ? serial8250_interrupt+0x0/0xb2
<4> [<c119ec07>] serial8250_startup+0x3f5/0x53d
<4> [<c119bfa9>] uart_startup+0x6e/0x101
<4> [<c119ca89>] uart_open+0xff/0x2ac
<4> [<c114fee7>] ? tty_init_dev+0xb7/0xf0
<4> [<c11501ab>] tty_open+0x28b/0x354
<4> [<c106336e>] chrdev_open+0xc0/0xd7
<4> [<c1060141>] __dentry_open+0xd1/0x1a7
<4> [<c10602ad>] nameidata_to_filp+0x29/0x3d
<4> [<c10632ae>] ? chrdev_open+0x0/0xd7
<4> [<c1068a92>] do_last+0x3d1/0x4d1
<4> [<c106a34f>] do_filp_open+0x38c/0x41e
<4> [<c10124c0>] ? do_page_fault+0x2a1/0x2cf
<4> [<c105ff43>] do_sys_open+0x48/0x116
<4> [<c1060053>] sys_open+0x1e/0x26
<4> [<c1002650>] sysenter_do_call+0x12/0x26
<4> [<c1300000>] ? dump_stack+0x40/0x60
<3>handlers:
<3>[<c119f173>] (serial8250_interrupt+0x0/0xb2) <0>Disabling IRQ #4

==================
If I enable the DB9-Port as 0x3f8/4 and the second of the internal ports as 0x2f8/3, I get the following:

<6>serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A <6>serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A <6>00:06: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A <6>00:08: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A

and later, when /dev/ttyS1 is accessed, and I touch the screen:

<4>ttyS1: 1 input overrun(s)

and no data at all.

Kind regards

Jan