Skip to contentSkip to conversation

(qcserial.c) Enable Diagnostics Monitor and GPS ports on Gobi 2000

PATCH New Matthias G. Eckermann 1 participant 1 message Sep 24, 2010

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 (qcserial.c) Enable Diagnostics Monitor and GPS ports on Gobi 2000

Hello all,

this patch to qcserial.c enables the Diagnostics Monitor and NMEA GPS ports on Qualcomm Gobi 2000 devices.

A Gobi 2000 device will provide 3 serial ports:

        # /dev/ttyUSB0 -> Diagnostics
        # /dev/ttyUSB1 -> 3G Modem
        # /dev/ttyUSB2 -> NMEA GPS port

* The Diagnostics Monitor uses Qualcomm's DM protocol; I used libqcdm (ModemManager) to talk to it, found it working, but at least DM commands 12 and 64 are not implemented on my device (Gobi 2000 built into Thinkpad x100e).

* Functionality of the 3G Modem port remains unchanged.

* The GPS port and how to enable it has been confirmed now in the Gobi 3000 source code at:
https://www.codeaurora.org/patches/quic/gobi/
Enable/disable GPS via:

        echo "\$GPS_START" > /dev/ttyUSB2
        # use GPS
        echo "\$GPS_STOP"  > /dev/ttyUSB2

---

drivers/usb/serial/qcserial.c +30 -1
index 2846ad8..1fac621 100644
@@ -150,21 +150,50 @@ static int qcprobe(struct usb_serial *serial, const struct usb_device_id *id)
 		break;
 
 	case 3:
 	case 4:
 		/* Composite mode */
-		if (ifnum == 2) {
+		/* ifnum == 0 is a broadband network adapter */
+		if (ifnum == 1) {
+			/* 
+			 * Diagnostics Monitor (serial line 9600 8N1)
+			 * Qualcomm DM protocol
+			 * use "libqcdm" (ModemManager) for communication
+			 */
+			dbg("Diagnostics Monitor found");
+			retval = usb_set_interface(serial->dev, ifnum, 0);
+			if (retval < 0) {
+				dev_err(&serial->dev->dev,
+					"Could not set interface, error %d\n",
+					retval);
+				retval = -ENODEV;
+			}
+		} else if (ifnum == 2) {
 			dbg("Modem port found");
 			retval = usb_set_interface(serial->dev, ifnum, 0);
 			if (retval < 0) {
 				dev_err(&serial->dev->dev,
 					"Could not set interface, error %d\n",
 					retval);
 				retval = -ENODEV;
 				kfree(data);
 			}
 			return retval;
+		} else if (ifnum==3) {
+			/* 
+			 * NMEA (serial line 9600 8N1)
+			 * # echo "\$GPS_START" > /dev/ttyUSBx
+			 * # echo "\$GPS_STOP"  > /dev/ttyUSBx
+			 */
+			dbg("NMEA GPS interface found");
+			retval = usb_set_interface(serial->dev, ifnum, 0);
+			if (retval < 0) {
+				dev_err(&serial->dev->dev,
+					"Could not set interface, error %d\n",
+					retval);
+				retval = -ENODEV;
+			}
 		}
 		break;
 
 	default:
 		dev_err(&serial->dev->dev,
Signature · 3 lines
Voluminous documentation is  part of the problem 
not part of the solution           (Tom DeMarco)
No documentation though is not a solution either