Skip to contentSkip to conversation

omap mmc: extended to pass host capabilities from board file

PATCH In review Sukumar Ghorai 2 participants 4 messages Sep 15, 2010 – Oct 1, 2010

Subsystems (6)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 omap mmc: extended to pass host capabilities from board file

wires variable is renamed, extended and this single variable to be used to pass the platform capabilities, e.g DDR mode. Also removed the hardcoded value was using as bus-width.

---
 arch/arm/mach-omap2/board-2430sdp.c          |    3 ++-
 arch/arm/mach-omap2/board-3430sdp.c          |    5 +++--
 arch/arm/mach-omap2/board-4430sdp.c          |    4 ++--
 arch/arm/mach-omap2/board-cm-t35.c           |    5 +++--
 arch/arm/mach-omap2/board-devkit8000.c       |    3 ++-
 arch/arm/mach-omap2/board-igep0020.c         |    5 +++--
 arch/arm/mach-omap2/board-ldp.c              |    3 ++-
 arch/arm/mach-omap2/board-n8x0.c             |    2 +-
 arch/arm/mach-omap2/board-omap3beagle.c      |    3 ++-
 arch/arm/mach-omap2/board-omap3evm.c         |    3 ++-
 arch/arm/mach-omap2/board-omap3pandora.c     |    7 ++++---
 arch/arm/mach-omap2/board-omap3stalker.c     |    3 ++-
 arch/arm/mach-omap2/board-omap3touchbook.c   |    3 ++-
 arch/arm/mach-omap2/board-omap4panda.c       |    2 +-
 arch/arm/mach-omap2/board-overo.c            |    5 +++--
 arch/arm/mach-omap2/board-rx51-peripherals.c |    5 +++--
 arch/arm/mach-omap2/board-zoom-peripherals.c |    5 +++--
 arch/arm/mach-omap2/devices.c                |   16 +++++++++-------
 arch/arm/mach-omap2/hsmmc.c                  |   16 ++++++++++------
 arch/arm/mach-omap2/hsmmc.h                  |    3 ++-
 arch/arm/plat-omap/include/plat/mmc.h        |    7 +++----
 drivers/mmc/host/omap.c                      |    2 +-
 drivers/mmc/host/omap_hsmmc.c                |   18 ++----------------
 23 files changed, 67 insertions(+), 61 deletions(-)
arch/arm/mach-omap2/board-2430sdp.c +2 -1
index 8538e41..fc178a0 100644
@@ -19,6 +19,7 @@
 #include <linux/mtd/mtd.h>
 #include <linux/mtd/partitions.h>
 #include <linux/mtd/physmap.h>
+#include <linux/mmc/host.h>
 #include <linux/delay.h>
 #include <linux/i2c/twl.h>
 #include <linux/err.h>
@@ -190,7 +191,7 @@ static int __init omap2430_i2c_init(void)
 static struct omap2_hsmmc_info mmc[] __initdata = {
 	{
 		.mmc		= 1,
-		.wires		= 4,
+		.caps		= MMC_CAP_4_BIT_DATA,
 		.gpio_cd	= -EINVAL,
 		.gpio_wp	= -EINVAL,
 		.ext_clock	= 1,
arch/arm/mach-omap2/board-3430sdp.c +3 -2
index 67b95b5..3eb9839 100644
@@ -24,6 +24,7 @@
 #include <linux/regulator/machine.h>
 #include <linux/io.h>
 #include <linux/gpio.h>
+#include <linux/mmc/host.h>
 
 #include <mach/hardware.h>
 #include <asm/mach-types.h>
@@ -353,12 +354,12 @@ static struct omap2_hsmmc_info mmc[] = {
 		/* 8 bits (default) requires S6.3 == ON,
 		 * so the SIM card isn't used; else 4 bits.
 		 */
-		.wires		= 8,
+		.caps		= MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA,
 		.gpio_wp	= 4,
 	},
 	{
 		.mmc		= 2,
-		.wires		= 8,
+		.caps		= MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA,
 		.gpio_wp	= 7,
 	},
 	{}	/* Terminator */
arch/arm/mach-omap2/board-4430sdp.c +2 -2
index 9447644..e379bef 100644
@@ -193,12 +193,12 @@ static struct omap_musb_board_data musb_board_data = {
 static struct omap2_hsmmc_info mmc[] = {
 	{
 		.mmc		= 1,
-		.wires		= 8,
+		.caps		= MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA,
 		.gpio_wp	= -EINVAL,
 	},
 	{
 		.mmc		= 2,
-		.wires		= 8,
+		.caps		=  MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA,
 		.gpio_cd	= -EINVAL,
 		.gpio_wp	= -EINVAL,
 		.nonremovable   = true,
arch/arm/mach-omap2/board-cm-t35.c +3 -2
index e10bc10..b72009a 100644
@@ -31,6 +31,7 @@
 #include <linux/i2c/at24.h>
 #include <linux/i2c/twl.h>
 #include <linux/regulator/machine.h>
+#include <linux/mmc/host.h>
 
 #include <linux/spi/spi.h>
 #include <linux/spi/tdo24m.h>
@@ -579,14 +580,14 @@ static struct twl4030_keypad_data cm_t35_kp_data = {
 static struct omap2_hsmmc_info mmc[] = {
 	{
 		.mmc		= 1,
-		.wires		= 4,
+		.caps		= MMC_CAP_4_BIT_DATA,
 		.gpio_cd	= -EINVAL,
 		.gpio_wp	= -EINVAL,
 
 	},
 	{
 		.mmc		= 2,
-		.wires		= 4,
+		.caps		= MMC_CAP_4_BIT_DATA,
 		.transceiver	= 1,
 		.gpio_cd	= -EINVAL,
 		.gpio_wp	= -EINVAL,
arch/arm/mach-omap2/board-devkit8000.c +2 -1
index a07086d..de5e2c2 100644
@@ -28,6 +28,7 @@
 #include <linux/mtd/mtd.h>
 #include <linux/mtd/partitions.h>
 #include <linux/mtd/nand.h>
+#include <linux/mmc/host.h>
 
 #include <linux/regulator/machine.h>
 #include <linux/i2c/twl.h>
@@ -105,7 +106,7 @@ static struct omap_nand_platform_data devkit8000_nand_data = {
 static struct omap2_hsmmc_info mmc[] = {
 	{
 		.mmc		= 1,
-		.wires		= 8,
+		.caps		= MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA,
 		.gpio_wp	= 29,
 	},
 	{}	/* Terminator */
arch/arm/mach-omap2/board-igep0020.c +3 -2
index 175f043..f3f0280 100644
@@ -20,6 +20,7 @@
 
 #include <linux/regulator/machine.h>
 #include <linux/i2c/twl.h>
+#include <linux/mmc/host.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
@@ -248,13 +249,13 @@ static struct regulator_init_data igep2_vmmc2 = {
 static struct omap2_hsmmc_info mmc[] = {
 	{
 		.mmc		= 1,
-		.wires		= 4,
+		.caps		= MMC_CAP_4_BIT_DATA,
 		.gpio_cd	= -EINVAL,
 		.gpio_wp	= -EINVAL,
 	},
 	{
 		.mmc		= 2,
-		.wires		= 4,
+		.caps		= MMC_CAP_4_BIT_DATA,
 		.gpio_cd	= -EINVAL,
 		.gpio_wp	= -EINVAL,
 	},
arch/arm/mach-omap2/board-ldp.c +2 -1
index 00d9b13..58698e3 100644
@@ -27,6 +27,7 @@
 #include <linux/i2c/twl.h>
 #include <linux/io.h>
 #include <linux/smsc911x.h>
+#include <linux/mmc/host.h>
 
 #include <mach/hardware.h>
 #include <asm/mach-types.h>
@@ -362,7 +363,7 @@ static int __init omap_i2c_init(void)
 static struct omap2_hsmmc_info mmc[] __initdata = {
 	{
 		.mmc		= 1,
-		.wires		= 4,
+		.caps		= MMC_CAP_4_BIT_DATA,
 		.gpio_cd	= -EINVAL,
 		.gpio_wp	= -EINVAL,
 	},
arch/arm/mach-omap2/board-n8x0.c +1 -1
index a3e2b49..64ef167 100644
@@ -487,7 +487,7 @@ static struct omap_mmc_platform_data mmc1_data = {
 	.max_freq			= 24000000,
 	.dma_mask			= 0xffffffff,
 	.slots[0] = {
-		.wires			= 4,
+		.caps			= MMC_CAP_4_BIT_DATA,
 		.set_power		= n8x0_mmc_set_power,
 		.set_bus_mode		= n8x0_mmc_set_bus_mode,
 		.get_cover_state	= n8x0_mmc_get_cover_state,
arch/arm/mach-omap2/board-omap3beagle.c +2 -1
index 87969c7..51493f5 100644
@@ -27,6 +27,7 @@
 #include <linux/mtd/mtd.h>
 #include <linux/mtd/partitions.h>
 #include <linux/mtd/nand.h>
+#include <linux/mmc/host.h>
 
 #include <linux/regulator/machine.h>
 #include <linux/i2c/twl.h>
@@ -166,7 +167,7 @@ static void __init beagle_display_init(void)
 static struct omap2_hsmmc_info mmc[] = {
 	{
 		.mmc		= 1,
-		.wires		= 8,
+		.caps		= MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA,
 		.gpio_wp	= 29,
 	},
 	{}	/* Terminator */
arch/arm/mach-omap2/board-omap3evm.c +2 -1
index f76d9c0..523ba55 100644
@@ -31,6 +31,7 @@
 #include <linux/smsc911x.h>
 
 #include <linux/regulator/machine.h>
+#include <linux/mmc/host.h>
 
 #include <mach/hardware.h>
 #include <asm/mach-types.h>
@@ -370,7 +371,7 @@ static struct regulator_init_data omap3evm_vsim = {
 static struct omap2_hsmmc_info mmc[] = {
 	{
 		.mmc		= 1,
-		.wires		= 4,
+		.caps		= MMC_CAP_4_BIT_DATA,
 		.gpio_cd	= -EINVAL,
 		.gpio_wp	= 63,
 	},
arch/arm/mach-omap2/board-omap3pandora.c +4 -3
index dd3af2b..2d2e6fc 100644
@@ -32,6 +32,7 @@
 #include <linux/input.h>
 #include <linux/input/matrix_keypad.h>
 #include <linux/gpio_keys.h>
+#include <linux/mmc/host.h>
 #include <linux/mmc/card.h>
 
 #include <asm/mach-types.h>
@@ -276,14 +277,14 @@ static void pandora_wl1251_init_card(struct mmc_card *card)
 static struct omap2_hsmmc_info omap3pandora_mmc[] = {
 	{
 		.mmc		= 1,
-		.wires		= 4,
+		.caps		= MMC_CAP_4_BIT_DATA,
 		.gpio_cd	= -EINVAL,
 		.gpio_wp	= 126,
 		.ext_clock	= 0,
 	},
 	{
 		.mmc		= 2,
-		.wires		= 4,
+		.caps		= MMC_CAP_4_BIT_DATA,
 		.gpio_cd	= -EINVAL,
 		.gpio_wp	= 127,
 		.ext_clock	= 1,
@@ -291,7 +292,7 @@ static struct omap2_hsmmc_info omap3pandora_mmc[] = {
 	},
 	{
 		.mmc		= 3,
-		.wires		= 4,
+		.caps		= MMC_CAP_4_BIT_DATA,
 		.gpio_cd	= -EINVAL,
 		.gpio_wp	= -EINVAL,
 		.init_card	= pandora_wl1251_init_card,
arch/arm/mach-omap2/board-omap3stalker.c +2 -1
index bcd01d2..c1b881d 100644
@@ -26,6 +26,7 @@
 
 #include <linux/regulator/machine.h>
 #include <linux/i2c/twl.h>
+#include <linux/mmc/host.h>
 
 #include <mach/hardware.h>
 #include <asm/mach-types.h>
@@ -275,7 +276,7 @@ static struct regulator_init_data omap3stalker_vsim = {
 static struct omap2_hsmmc_info mmc[] = {
 	{
 	 .mmc		= 1,
-	 .wires		= 4,
+	 .caps		= MMC_CAP_4_BIT_DATA,
 	 .gpio_cd	= -EINVAL,
 	 .gpio_wp	= 23,
 	 },
arch/arm/mach-omap2/board-omap3touchbook.c +2 -1
index 663c62d..9ab18fd 100644
@@ -27,6 +27,7 @@
 #include <linux/mtd/mtd.h>
 #include <linux/mtd/partitions.h>
 #include <linux/mtd/nand.h>
+#include <linux/mmc/host.h>
 
 #include <plat/mcspi.h>
 #include <linux/spi/spi.h>
@@ -108,7 +109,7 @@ static struct omap_nand_platform_data omap3touchbook_nand_data = {
 static struct omap2_hsmmc_info mmc[] = {
 	{
 		.mmc		= 1,
-		.wires		= 8,
+		.caps		= MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA,
 		.gpio_wp	= 29,
 	},
 	{}	/* Terminator */
arch/arm/mach-omap2/board-omap4panda.c +1 -1
index c03d1d5..81e756d 100644
@@ -56,7 +56,7 @@ static struct omap_musb_board_data musb_board_data = {
 static struct omap2_hsmmc_info mmc[] = {
 	{
 		.mmc		= 1,
-		.wires		= 8,
+		.caps		= MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA,
 		.gpio_wp	= -EINVAL,
 	},
 	{}	/* Terminator */
arch/arm/mach-omap2/board-overo.c +3 -2
index 4c48436..93441e5 100644
@@ -32,6 +32,7 @@
 #include <linux/mtd/mtd.h>
 #include <linux/mtd/nand.h>
 #include <linux/mtd/partitions.h>
+#include <linux/mmc/host.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
@@ -303,13 +304,13 @@ static void __init overo_flash_init(void)
 static struct omap2_hsmmc_info mmc[] = {
 	{
 		.mmc		= 1,
-		.wires		= 4,
+		.caps		= MMC_CAP_4_BIT_DATA,
 		.gpio_cd	= -EINVAL,
 		.gpio_wp	= -EINVAL,
 	},
 	{
 		.mmc		= 2,
-		.wires		= 4,
+		.caps		= MMC_CAP_4_BIT_DATA,
 		.gpio_cd	= -EINVAL,
 		.gpio_wp	= -EINVAL,
 		.transceiver	= true,
arch/arm/mach-omap2/board-rx51-peripherals.c +3 -2
index 9a5eb87..a3dbaa7 100644
@@ -302,7 +302,7 @@ static struct omap2_hsmmc_info mmc[] __initdata = {
 	{
 		.name		= "external",
 		.mmc		= 1,
-		.wires		= 4,
+		.caps		= MMC_CAP_4_BIT_DATA,
 		.cover_only	= true,
 		.gpio_cd	= 160,
 		.gpio_wp	= -EINVAL,
@@ -311,7 +311,8 @@ static struct omap2_hsmmc_info mmc[] __initdata = {
 	{
 		.name		= "internal",
 		.mmc		= 2,
-		.wires		= 8, /* See also rx51_mmc2_remux */
+		.caps		= MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA,
+						/* See also rx51_mmc2_remux */
 		.gpio_cd	= -EINVAL,
 		.gpio_wp	= -EINVAL,
 		.nonremovable	= true,
arch/arm/mach-omap2/board-zoom-peripherals.c +3 -2
index 6b39849..e5eac46 100644
@@ -16,6 +16,7 @@
 #include <linux/gpio.h>
 #include <linux/i2c/twl.h>
 #include <linux/regulator/machine.h>
+#include <linux/mmc/host.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
@@ -155,14 +156,14 @@ static struct omap2_hsmmc_info mmc[] __initdata = {
 	{
 		.name		= "external",
 		.mmc		= 1,
-		.wires		= 4,
+		.caps		= MMC_CAP_4_BIT_DATA,
 		.gpio_wp	= -EINVAL,
 		.power_saving	= true,
 	},
 	{
 		.name		= "internal",
 		.mmc		= 2,
-		.wires		= 8,
+		.caps		= MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA,
 		.gpio_cd	= -EINVAL,
 		.gpio_wp	= -EINVAL,
 		.nonremovable	= true,
arch/arm/mach-omap2/devices.c +9 -7
index 2dbb265..9390750 100644
@@ -624,7 +624,7 @@ static inline void omap2_mmc_mux(struct omap_mmc_platform_data *mmc_controller,
 		omap_mux_init_signal("sdmmc_dat0", 0);
 		omap_mux_init_signal("sdmmc_dat_dir0", 0);
 		omap_mux_init_signal("sdmmc_cmd_dir", 0);
-		if (mmc_controller->slots[0].wires == 4) {
+		if (mmc_controller->slots[0].caps & MMC_CAP_4_BIT_DATA) {
 			omap_mux_init_signal("sdmmc_dat1", 0);
 			omap_mux_init_signal("sdmmc_dat2", 0);
 			omap_mux_init_signal("sdmmc_dat3", 0);
@@ -652,8 +652,8 @@ static inline void omap2_mmc_mux(struct omap_mmc_platform_data *mmc_controller,
 				OMAP_PIN_INPUT_PULLUP);
 			omap_mux_init_signal("sdmmc1_dat0",
 				OMAP_PIN_INPUT_PULLUP);
-			if (mmc_controller->slots[0].wires == 4 ||
-				mmc_controller->slots[0].wires == 8) {
+			if (mmc_controller->slots[0].caps &
+				(MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA)) {
 				omap_mux_init_signal("sdmmc1_dat1",
 					OMAP_PIN_INPUT_PULLUP);
 				omap_mux_init_signal("sdmmc1_dat2",
@@ -661,7 +661,8 @@ static inline void omap2_mmc_mux(struct omap_mmc_platform_data *mmc_controller,
 				omap_mux_init_signal("sdmmc1_dat3",
 					OMAP_PIN_INPUT_PULLUP);
 			}
-			if (mmc_controller->slots[0].wires == 8) {
+			if (mmc_controller->slots[0].caps &
+						MMC_CAP_8_BIT_DATA) {
 				omap_mux_init_signal("sdmmc1_dat4",
 					OMAP_PIN_INPUT_PULLUP);
 				omap_mux_init_signal("sdmmc1_dat5",
@@ -685,8 +686,8 @@ static inline void omap2_mmc_mux(struct omap_mmc_platform_data *mmc_controller,
 			 * For 8 wire configurations, Lines DAT4, 5, 6 and 7 need to be muxed
 			 * in the board-*.c files
 			 */
-			if (mmc_controller->slots[0].wires == 4 ||
-				mmc_controller->slots[0].wires == 8) {
+			if (mmc_controller->slots[0].caps &
+				(MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA)) {
 				omap_mux_init_signal("sdmmc2_dat1",
 					OMAP_PIN_INPUT_PULLUP);
 				omap_mux_init_signal("sdmmc2_dat2",
@@ -694,7 +695,8 @@ static inline void omap2_mmc_mux(struct omap_mmc_platform_data *mmc_controller,
 				omap_mux_init_signal("sdmmc2_dat3",
 					OMAP_PIN_INPUT_PULLUP);
 			}
-			if (mmc_controller->slots[0].wires == 8) {
+			if (mmc_controller->slots[0].caps &
+							MMC_CAP_8_BIT_DATA) {
 				omap_mux_init_signal("sdmmc2_dat4.sdmmc2_dat4",
 					OMAP_PIN_INPUT_PULLUP);
 				omap_mux_init_signal("sdmmc2_dat5.sdmmc2_dat5",
arch/arm/mach-omap2/hsmmc.c +10 -6
index c8f647b..87ce6ff 100644
@@ -258,7 +258,7 @@ void __init omap2_hsmmc_init(struct omap2_hsmmc_info *controllers)
 				"mmc%islot%i", c->mmc, 1);
 		mmc->slots[0].name = hc->name;
 		mmc->nr_slots = 1;
-		mmc->slots[0].wires = c->wires;
+		mmc->slots[0].caps = c->caps;
 		mmc->slots[0].internal_clock = !c->ext_clock;
 		mmc->dma_mask = 0xffffffff;
 
@@ -316,16 +316,20 @@ void __init omap2_hsmmc_init(struct omap2_hsmmc_info *controllers)
 			}
 
 			/* Omap3630 HSMMC1 supports only 4-bit */
-			if (cpu_is_omap3630() && c->wires > 4) {
-				c->wires = 4;
-				mmc->slots[0].wires = c->wires;
+			if (cpu_is_omap3630() &&
+					(c->caps & MMC_CAP_8_BIT_DATA)) {
+				c->caps &= ~MMC_CAP_8_BIT_DATA;
+				c->caps |= MMC_CAP_4_BIT_DATA;
+				mmc->slots[0].caps = c->caps;
 			}
 			break;
 		case 2:
 			if (c->ext_clock)
 				c->transceiver = 1;
-			if (c->transceiver && c->wires > 4)
-				c->wires = 4;
+			if (c->transceiver && (c->caps & MMC_CAP_8_BIT_DATA)) {
+				c->caps &= ~MMC_CAP_8_BIT_DATA;
+				c->caps |= MMC_CAP_4_BIT_DATA;
+			}
 			/* FALLTHROUGH */
 		case 3:
 			if (mmc->slots[0].features & HSMMC_HAS_PBIAS) {
arch/arm/mach-omap2/hsmmc.h +2 -1
index 1fe6f01..281e972 100644
@@ -10,7 +10,8 @@ struct mmc_card;
 
 struct omap2_hsmmc_info {
 	u8	mmc;		/* controller 1/2/3 */
-	u8	wires;		/* 1/4/8 wires */
+	u32	caps;		/* 4/8 wires and any additional host
+				 * capabilities OR'd (ref. linux/mmc/host.h) */
 	bool	transceiver;	/* MMC-2 option */
 	bool	ext_clock;	/* use external pin for input clock */
 	bool	cover_only;	/* No card detect - just cover switch */
arch/arm/plat-omap/include/plat/mmc.h +3 -4
index 9b89ec6..4f819fc 100644
@@ -73,10 +73,9 @@ struct omap_mmc_platform_data {
 
 	struct omap_mmc_slot_data {
 
-		/* 4 wire signaling is optional, and is used for SD/SDIO/HSMMC;
-		 * 8 wire signaling is also optional, and is used with HSMMC
-		 */
-		u8 wires;
+		/* 4/8 wires and any additional host capabilities
+		 * need to OR'd all capabilities (ref. linux/mmc/host.h) */
+		u32 caps;
 
 		/*
 		 * nomux means "standard" muxing is wrong on this board, and
drivers/mmc/host/omap.c +1 -1
index d98ddcf..a9d62cf 100644
@@ -1317,7 +1317,7 @@ static int __init mmc_omap_new_slot(struct mmc_omap_host *host, int id)
 	host->slots[id] = slot;
 
 	mmc->caps = 0;
-	if (host->pdata->slots[id].wires >= 4)
+	if (host->pdata->slots[id].caps & MMC_CAP_8_BIT_DATA)
 		mmc->caps |= MMC_CAP_4_BIT_DATA;
 
 	mmc->ops = &mmc_omap_ops;
drivers/mmc/host/omap_hsmmc.c +2 -16
index 1c359f0..fe1d391 100644
@@ -2124,23 +2124,9 @@ static int __init omap_hsmmc_probe(struct platform_device *pdev)
 	mmc->caps |= MMC_CAP_MMC_HIGHSPEED | MMC_CAP_SD_HIGHSPEED |
 		     MMC_CAP_WAIT_WHILE_BUSY | MMC_CAP_ERASE;
 
-	switch (mmc_slot(host).wires) {
-	case 8:
-		mmc->caps |= MMC_CAP_8_BIT_DATA;
-		/* Fall through */
-	case 4:
+	mmc->caps |= mmc_slot(host).caps;
+	if (mmc->caps & MMC_CAP_8_BIT_DATA)
 		mmc->caps |= MMC_CAP_4_BIT_DATA;
-		break;
-	case 1:
-		/* Nothing to crib here */
-	case 0:
-		/* Assuming nothing was given by board, Core use's 1-Bit */
-		break;
-	default:
-		/* Completely unexpected.. Core goes with 1-Bit Width */
-		dev_crit(mmc_dev(host->mmc), "Invalid width %d\n used!"
-			"using 1 instead\n", mmc_slot(host).wires);
-	}
 
 	if (mmc_slot(host).nonremovable)
 		mmc->caps |= MMC_CAP_NONREMOVABLE;
maintainer
#1 lore raw
Quoted 3 lines · Sukumar Ghorai

wires variable is renamed, extended and this single variable to be used to pass the platform capabilities, e.g DDR mode. Also removed the hardcoded value was using as bus-width.

This looks like a nice clean-up, I'll queue this via the omap patches.

Regards,

Tony

maintainer
#2 lore raw

PATCH 1/1 omap: Keep nwires for omap1 and 2420 MMC controller (Re: [PATCH] omap mmc: extended to pass host capabilities from board file)

Quoted 7 lines · Tony Lindgren
Quoted 3 lines · Sukumar Ghorai

wires variable is renamed, extended and this single variable to be used to pass the platform capabilities, e.g DDR mode. Also removed the hardcoded value was using as bus-width.

This looks like a nice clean-up, I'll queue this via the omap patches.

And of course this patch breaks all of mach-omap1 and omap2420.

Sukumar, your patch modified also drivers/mmc/host/omap.c and board-n8x0.c to use caps instead of nwires. When you do things like that you absolutely _must_test_your_changes_ before sending out any patches.

Planning on merging the following fix.

Tony

From: Tony Lindgren <[email protected]>
Date: Thu, 30 Sep 2010 10:25:46 -0700
Subject: [PATCH] Subject: [PATCH] omap: Keep nwires for omap1 and 2420 MMC controller

A patch from Sukumar Ghorai <[email protected]> changed the nwires to use caps instead. However, nwires is still needed for the earlier controller.

arch/arm/mach-omap2/board-n8x0.c +1 -1
index abd7e77..6bd9d9a 100644
@@ -488,7 +488,7 @@ static struct omap_mmc_platform_data mmc1_data = {
 	.max_freq			= 24000000,
 	.dma_mask			= 0xffffffff,
 	.slots[0] = {
-		.caps			= MMC_CAP_4_BIT_DATA,
+		.wires			= 4,
 		.set_power		= n8x0_mmc_set_power,
 		.set_bus_mode		= n8x0_mmc_set_bus_mode,
 		.get_cover_state	= n8x0_mmc_get_cover_state,
arch/arm/plat-omap/include/plat/mmc.h +10 -3
index 4f819fc..bc85010 100644
@@ -73,9 +73,16 @@ struct omap_mmc_platform_data {
 
 	struct omap_mmc_slot_data {
 
-		/* 4/8 wires and any additional host capabilities
-		 * need to OR'd all capabilities (ref. linux/mmc/host.h) */
-		u32 caps;
+		/*
+		 * 4/8 wires and any additional host capabilities
+		 * need to OR'd all capabilities (ref. linux/mmc/host.h)
+		 */
+#if defined(CONFIG_ARCH_OMAP1) || defined(CONFIG_ARCH_OMAP2420)
+		u8  wires;	/* Used for the MMC driver on omap1 and 2420 */
+#endif
+#ifdef CONFIG_ARCH_OMAP2PLUS
+		u32 caps;	/* Used for the MMC driver on 2430 and later */
+#endif
 
 		/*
 		 * nomux means "standard" muxing is wrong on this board, and
drivers/mmc/host/omap.c +1 -1
index a9d62cf..d98ddcf 100644
@@ -1317,7 +1317,7 @@ static int __init mmc_omap_new_slot(struct mmc_omap_host *host, int id)
 	host->slots[id] = slot;
 
 	mmc->caps = 0;
-	if (host->pdata->slots[id].caps & MMC_CAP_8_BIT_DATA)
+	if (host->pdata->slots[id].wires >= 4)
 		mmc->caps |= MMC_CAP_4_BIT_DATA;
 
 	mmc->ops = &mmc_omap_ops;
author Acked-by on v1 1/1
#3 lore raw

RE: [PATCH] omap: Keep nwires for omap1 and 2420 MMC controller (Re: [PATCH] omap mmc: extended to pass host capabilities from board file)

Quoted 94 lines

-----Original Message-----
From: Tony Lindgren [mailto:[email protected]]
Sent: Friday, October 01, 2010 12:08 AM
To: Ghorai, Sukumar
Cc: [email protected]; [email protected]
Subject: [PATCH] omap: Keep nwires for omap1 and 2420 MMC controller (Re:
[PATCH] omap mmc: extended to pass host capabilities from board file)

Quoted 2 lines · Tony Lindgren
Quoted 1 line · Sukumar Ghorai

wires variable is renamed, extended and this single variable to be

used to

Quoted 1 line
Quoted 1 line

pass the platform capabilities, e.g DDR mode. Also removed the

hardcoded

Quoted 4 lines
Quoted 1 line

value was using as bus-width.

This looks like a nice clean-up, I'll queue this via the omap patches.

And of course this patch breaks all of mach-omap1 and omap2420.

Sukumar, your patch modified also drivers/mmc/host/omap.c and board-n8x0.c to use caps instead of nwires. When you do things like that you absolutely _must_test_your_changes_ before sending out any patches.

Planning on merging the following fix.

Tony

From: Tony Lindgren <[email protected]>
Date: Thu, 30 Sep 2010 10:25:46 -0700
Subject: [PATCH] Subject: [PATCH] omap: Keep nwires for omap1 and 2420 MMC controller

A patch from Sukumar Ghorai <[email protected]> changed the nwires to use caps instead. However, nwires is still needed for the earlier controller.

arch/arm/mach-omap2/board- renamed from arch/arm/mach-omap2/board-n8x0.c +0 -0

n8x0.c
index abd7e77..6bd9d9a 100644

arch/arm/mach-omap2/board-n8x0.c +1 -1
@@ -488,7 +488,7 @@ static struct omap_mmc_platform_data mmc1_data = {
 	.max_freq			= 24000000,
 	.dma_mask			= 0xffffffff,
 	.slots[0] = {
-		.caps			= MMC_CAP_4_BIT_DATA,
+		.wires			= 4,
 		.set_power		= n8x0_mmc_set_power,
 		.set_bus_mode		= n8x0_mmc_set_bus_mode,
 		.get_cover_state	= n8x0_mmc_get_cover_state,
arch/arm/plat- renamed from arch/arm/plat-omap/include/plat/mmc.h +0 -0

omap/include/plat/mmc.h
index 4f819fc..bc85010 100644

arch/arm/plat-omap/include/plat/mmc.h +10 -3
@@ -73,9 +73,16 @@ struct omap_mmc_platform_data {
 
 	struct omap_mmc_slot_data {
 
-		/* 4/8 wires and any additional host capabilities
-		 * need to OR'd all capabilities (ref. linux/mmc/host.h) */
-		u32 caps;
+		/*
+		 * 4/8 wires and any additional host capabilities
+		 * need to OR'd all capabilities (ref. linux/mmc/host.h)
+		 */
+#if defined(CONFIG_ARCH_OMAP1) || defined(CONFIG_ARCH_OMAP2420)
+		u8  wires;	/* Used for the MMC driver on omap1 and 2420 */
+#endif
+#ifdef CONFIG_ARCH_OMAP2PLUS
+		u32 caps;	/* Used for the MMC driver on 2430 and later */
+#endif
 
 		/*
 		 * nomux means "standard" muxing is wrong on this board, and
drivers/mmc/host/omap.c +1 -1
index a9d62cf..d98ddcf 100644
@@ -1317,7 +1317,7 @@ static int __init mmc_omap_new_slot(struct
 mmc_omap_host *host, int id)
 	host->slots[id] = slot;
 
 	mmc->caps = 0;
-	if (host->pdata->slots[id].caps & MMC_CAP_8_BIT_DATA)
+	if (host->pdata->slots[id].wires >= 4)
 		mmc->caps |= MMC_CAP_4_BIT_DATA;
 
Quoted 1 line

mmc->ops = &mmc_omap_ops;

[Ghorai] thanks.. I am agreeing with you;