Skip to contentSkip to conversation

U-Boot 1.3.4 CONFIG_SILENT_CONSOLE Does Not Work?

U-Boot NB 3 participants 5 messages Sep 30, 2010 – Oct 2, 2010

lore
Share & tools
lore

NB

author
#0 lore raw

I'm using U-Boot 1.3.4. When building I've defined "CONFIG_SILENT_CONSOLE" and "CFG_DEVICE_NULLDEV". My board is an at91sam9261ek.

My U-Boot environment looks like this via "printenv":

bootargs=mem=64M console=ttyS0,115200 mtdparts=atmel_nand:4M(kernel)ro,-(rootfs) root=/dev/mtdblock1 rw rootfstype=jffs2
bootcmd=nand read 0x22200000 0x00000000 0x0019757C; bootm 0x22200000 bootdelay=1
baudrate=115200
silent=1

However when I boot my device I see u-boot spiting out the same stuff it does even if "silent" isn't selected, as well as linux but I'm focusing on getting u- boot working as the README / README.silent suggests first.

I know I've seen a few others on this group with the exact same problem as me, and the official response was "RTFM", but, unless I'm missing something hidden in the README's I need a little help, or there is a bug with u-boot.

Anyone can suggest something? Should "silent" be set to a specific variable? Is the stuff I see below normal for "silent", and it is working as it should?

This is what I get on the hyperterminal with the above configuration:

U-Boot 1.3.4 (Sep 30 2010 - 12:33:45)

DRAM:  64 MB
NAND:  256 MiB
DataFlash:AT45DB642
Nb pages:   8192
Page Size:   1056
Size= 8650752 bytes
Logical address: 0xC0000000
Area 0: C0000000 to C00041FF (RO) Bootstrap
Area 1: C0004200 to C00083FF      Environment
Area 2: C0008400 to C0041FFF (RO) U-Boot
Area 3: C0042000 to C0251FFF      Kernel
Area 4: C0252000 to C083FFFF      FS
In:    serial
Out:   serial
Err:   serial
Hit any key to stop autoboot:  0

NAND read: device 0 offset 0x0, size 0x19757c
1668476 bytes read: OK
## Booting kernel from Legacy Image at 22200000 ...

   Image Name:   Angstrom/2.6.30/at91sam9261ek
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1668412 Bytes =  1.6 MB

Load Address: 20008000
Entry Point: 20008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK

Starting kernel ...

Uncompressing Linux.............................................................
...............................................
[[[.SNIP.]]]

#1 lore raw

Dear NB,

Quoted 2 lines · In message <[email protected]> you wrote:

I'm using U-Boot 1.3.4. When building I've defined "CONFIG_SILENT_CONSOLE" and "CFG_DEVICE_NULLDEV". My board is an at91sam9261ek.

You are aware that U-Boot 1.3.4 is moe than 2 years old and as such hopelessly obsolete, aren't you? Don;t expect much help for ancient versions like this...

I can only comment on current code...

Quoted 1 line

Anyone can suggest something? Should "silent" be set to a specific variable?

No. The actual value of the "silent" environment variable is not checked, only if it exists or not.

Quoted 1 line

Is the stuff I see below normal for "silent", and it is working as it should?

No, you are not supposed to see that output.

Best regards,

Wolfgang Denk

Signature · 5 lines
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
Systems programmers are the high priests of a low cult.
                                                       -- R.S. Barton
author
#2 lore raw
Quoted 5 lines · Wolfgang Denk <wd <at> denx.de> writes:

You are aware that U-Boot 1.3.4 is moe than 2 years old and as such hopelessly obsolete, aren't you? Don;t expect much help for ancient versions like this...

I can only comment on current code...

Yeah. I've tried U-Boot 2010-06 but it doesn't have 9g10 support yet *which my custom board is using*, so I think I'm forced to use the linux4sam updated u-boot 1.3.4, or to port the patches myself; but my tests right now were just with uboot 1.3.4 and a 9261ek.

Basically I just wanted to know if I'm doing everything right and not missing a step, since others have posted with my same problems ~2 years ago when 1.3.4 was current, and it sounded like it was working from the replys.

I'm guessing now there is/was a bug but maybe it has already been fixed. When I get some free time I can re-build oe's uboot 2010-06 with SILENT support to see if it is working for a 9261ek.

If someone remembers anything about the "old" 1.3.4 + silent feature do mention it :)

Thanks

#3 lore raw
In reply to NB
Quoted 3 lines · On Thursday, September 30, 2010 16:05:49 NB wrote:

However when I boot my device I see u-boot spiting out the same stuff it does even if "silent" isn't selected, as well as linux but I'm focusing on getting u- boot working as the README / README.silent suggests first.

ive seen issues depending on the env location. if the env cannot be loaded early, the *default env* is consulted for its silent settings, and then things "work" once the saved env is relocated.

might also want to check CONSOLE_IS_IN_ENV is enabled.

otherwise, your options are:
- trace the code yourself
- upgrade, and then trace the code yourself
-mike
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 836 bytes
Desc: This is a digitally signed message part.
Url : http://lists.denx.de/pipermail/u-boot/attachments/20100930/eaee60a4/attachment.pgp

author
#4 lore raw
Quoted 5 lines · Mike Frysinger <vapier <at> gentoo.org> writes:

ive seen issues depending on the env location. if the env cannot be loaded early, the *default env* is consulted for its silent settings, and then "work" once the saved env is relocated.

might also want to check CONSOLE_IS_IN_ENV is enabled.

Yeah I think you are right. CONSOLE_IS_IN_ENV is enabled for me, but at91sam9261ek also has CONFIG_SKIP_LOWLEVEL_INIT and CONFIG_SKIP_RELOCATE_UBOOT, so that RELOCATE issue is probably what is hindering me.

I looked at the console_init function (part where it is doing if(getenv("silent") != NULL)... and that is always returning null, even if it is set dynamically and rebooted.

What I did was change the check so it looks at a jumper instead of the getenv("silent") since this is what I wanted it to do anyway and it seems to all work now :).

I do notice that U-Boot is silencing everything except the "uncompressing kernel.............................." but I see the file related to that and should be able to fix it.

Thanks for your help.